VTech CS6529 Manuel utilisateur

Marque: VTech

Modèle: CS6529

Catégorie: Téléphones

Taper: Manuel utilisateur

CS6529/CS6529-14/

CS6529-15/CS6529-16/

CS6529-17/CS6529-19

CS6529-2/CS6529-25/

CS6529-26/CS6529-3

CS6529-4/CS6529-4B

DECT 6.0 cordless telephone

Introduction

To help protect the environment, this Abridged user’s manual provides you with

the basic installation and use instructions. A limited set of features are described in

abbreviated form.

Please refer to the online User’s manual for a full set of installation and operation

instructions at www.vtechphones.com.

Before using this VTech product, please read Important safety instructions on

pages 12 of this user’s manual.

Telephones identified with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of

the Telecommunications Industry Association. Used under license.

Abridged user’s manual

Compatible with

Hearing Aid T-Coil

TIA-1083

Go to www.vtechphones.com to register your product for enhanced warranty

support and latest VTech product news.

Parts checklist

Your telephone package contains the following items. Save your sales receipt and

original packaging in the event warranty service is necessary.

Telephone

line cord

Telephone base

power adapter

Handset

(1 for CS6529/CS6529-14/

CS6529-15/ CS6529-16/

CS6529-17/ CS6529-19/

(2 for CS6529-2/CS6529-25

CS6529-26)

(3 for CS6529-3)

(4 for CS6529-4/CS6529-4B)

Battery

(1 for CS6529/CS6529-14/

CS6529-15/ CS6529-16/

CS6529-17/ CS6529-19/

(2 for CS6529-2/CS6529-25

CS6529-26)

(3 for CS6529-3)

(4 for CS6529-4/CS6529-4B)

Battery compartment

cover

(1 for CS6529/CS6529-14/

CS6529-15/ CS6529-16/

CS6529-17/ CS6529-19/

(2 for CS6529-2/CS6529-25

CS6529-26)

(3 for CS6529-3)

(4 for CS6529-4/CS6529-4B)

Charger and

charger adapter

(1 for CS6529-2/CS6529-25

CS6529-26)

(2 for CS6529-3)

(3 for CS6529-4/CS6529-4B)

Wall mount

bracket

Telephone base

Telephone base and charger installation

Install the telephone base and charger as shown below.

Use only the power adapters and batteries supplied with this product. To order a

replacement, visit our website at www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.

•

Telephone base Charger

Electrical outlet

(not controlled

by a wall switch)

Telephone base

power adapter

Telephone line cord

Telephone wall jack

Charger

adapter

Electrical outlet

(not controlled

by a wall switch)

A DSL filter (not

included) is required

if you have DSL

high-speed Internet

service.

The DSL filter must

be plugged into the

telephone wall jack.

Abridged user’s manual

Quick start guide

Battery charging

Once you have installed the battery, the screen indicates the battery status (see

the table below). For best performance, keep the handset in the telephone base

or charger when not in use. The battery is fully charged after 11 hours of

continuous charging.

Battery indicators Battery status Action

The screen is blank, or

displays Put in charger

and flashes.

The battery has no or very little

charge. The handset cannot

be used.

Charge without interruption

(at least 30 minutes).

The screen displays

Low battery and flashes.

The battery has enough charge

to be used for a short time. Charge without interruption

(about 30 minutes).

The screen displays

HANDSET X.The battery is charged.

To keep the battery

charged, place it in the

telephone base or charger

when not in use.

Battery installation

Install the battery as shown below.

Plug the battery connector

securely into the socket.

1. Place the battery with the label

THIS SIDE UP facing up and

the wires inside the battery

compartment.

Slide the battery compartment cover

towards the center of the handset until

it clicks into place.

3. Place the handset in the telephone

base or charger to charge.

CHARGE light

remains on

when charging.

Wall mounting (optional)

To mount your telephone on a wall:

Route the telephone line cord through

the hole on the wall mount bracket

and plug it into the telephone wall

jack. Route the power cord out of the

telephone base and plug it into an

electrical outlet not controlled by a

wall switch.

3. Align the holes on the bracket with

the standard wall plate and slide the

bracket down until it locks securely.

Bundle the telephone line cord

and power adapter cord neatly

with twist ties.

Position the telephone base against

the wall mount bracket with the

extended tabs marked B on top.

Insert the extended tabs marked B

on the wall mount bracket into the

slots marked B on the back of the

telephone base. Push the telephone

base down until it clicks securely.

Remove the telephone line cord

from the telephone wall jack, and the

telephone base power adapter from

the electrical outlet (if necessary).

Handset overview CID/ /VOLUME

Review the caller ID log when

the phone is not in use.

Decrease the listening volume

during a call or message

playback.

Scroll down while in a menu,

or in the directory, caller ID log

or redial list.

Move the cursor to the left

when entering numbers or

names.

•

/FLASH

Make or answer a call.

Answer another incoming call

during a call.

•

MUTE/DELETE

Mute the microphone during

a call.

Delete digits or characters

while using the dialing keys.

Silence the ringer temporarily

while the handset is ringing.

Delete the displayed entry

while in the directory, caller ID

log or redial list.

•

CHARGE light

On when the handset is

charging.

•

/ /VOLUME

Review the directory when the

phone is not in use.

Increase the listening volume

during a call or message

playback.

Scroll up while in a menu, or

in the directory, caller ID log or

redial list.

Move the cursor to the right

when entering numbers or

names.

•

MENU/SELECT

Show the menu.

While in a menu, press to

select an item, or save an

entry or setting.

•

OFF/CANCEL

Hang up a call.

Silence the ringer temporarily

while the handset is ringing.

Press and hold to erase the

missed call indicator while the

phone is not in use.

Press to return to the previous

menu, or press and hold to

return to idle mode, without

making changes.

•

REDIAL/PAUSE

Press repeatedly to review the

redial list.

Press and hold to insert a

dialing pause while dialing or

entering a number.

•

QUIET#

Press and hold to set and turn

on the quiet mode, or turn it off.

Press repeatedly to show other

dialing options when reviewing

a caller ID log entry.

•

INT

Start an intercom conversation

or transfer a call (for

multi-handset models only).

•

Dialing keys

Enter numbers or characters.•

TONE

Switch to tone dialing

temporarily during a call.

•

Make or answer a call using the

handset speakerphone.

During a call, press to switch

between the speakerphone and

the handset.

•

Press repeatedly to add or

remove 1 in front of the caller

ID log entry before dialing or

saving it to the directory.

Press and hold to set or dial

your voicemail number.

•

Telephone base overview

X/DELETE

Delete the playing message.

Press twice to delete

all previously reviewed

messages when the phone is

not in use.

•

Message window

Shows the number of messages, and other

information of the answering system or

telephone base.

•

IN USE light

Flashes when there is an

incoming call, or another

telephone sharing the

same line is in use.

On when the handset is

in use, or the answering

system is answering a call.

•

FIND HANDSET

Press to page all system

handsets.

•

/SKIP

Skip to the next message.•

/ PLAY/STOP

Play or stop playing messages.

ANS ON/OFF

Turn the answering system

on or off.

•

/REPEAT

Press to repeat a message.

Press twice to play the

previous message.

•

VOL+ and VOL-

Adjust the volume during

message playback.

Adjust the telephone base

ringer volume when the

phone is not in use.

•

Using the menu

Press MENU when the handset is not in use.

Press or until the screen displays the desired feature menu.

Press SELECT.

To return to the previous menu, press CANCEL.

To return to idle mode, press and hold CANCEL.

Telephone settings

Default settings are indicated by asterisks (*).

Menu setting Description Options

LCD language Set the screen display language. English*

Français

Español

Voicemail # Set the speed dial voicemail number. Voicemail #

Clr voicemail Turn off the voicemail indicators (see the note

below). Reset VM Icon?

Key tone Set whether the handset beeps whenever a

key is pressed. Key tone:On*

Key tone:Off

Home area code Set the home area code so that the caller ID

log stores only seven digits for local

telephone numbers.

Home area code

_ _ _

Dial mode Set the telephone to be touch-tone or pulse

dialing. Touch-tone*

Pulse

The following are some of the telephone features you may wish to set. Refer to

Telephone settings in the online Complete user’s manual for complete instructions

on setting all telephone features.

Ringer volume (handset)

You can adjust the ringer volume level, or turn the ringer off.

Press MENU when the handset is not in use.

Scroll to Ringers and then press SELECT twice.

Press or to sample each volume level, then press SELECT to save.

When the ringer volume is set to Off, the handset still rings when you press

FIND HANDSET on the telephone base.

Set date and time

If you subscribe to caller ID service, the day, month and time are set automatically

with each incoming call. You can also set the date and time manually.

Press MENU when the handset is not in use.

Scroll to Set date/time and then press SELECT.

Use the dialing keys (0-9) to enter the month (MM), date (DD) and year (YY).

Then press SELECT.

Use the dialing keys (0-9) to enter the hour (HH) and minute (MM).

Then press or to choose AM or PM.

Press SELECT to save.

Telephone operation

Make a call

Press or and then dial the telephone number.

Answer a call

Press , or any dialing key.

End a call

Press OFF or put the handset to the telephone base or charger.

Speakerphone

During a call, press to switch between speakerphone

and normal handset use.

Volume

During a call, press VOLUME/ or VOLUME/ to adjust

the listening volume.

•

Use the Clr voicemail feature when the telephone indicates there is new voicemail but

there is none. For example, when you have accessed your voicemail while away from

home. The Clr voicemail feature only turns off the indicators; it does not delete your

voicemail messages. As long as you have new voicemail messages, your telephone

service provider continues to send the signal that turns on the indicators.

Mute

The mute function allows you to hear the other party but the other party cannot hear you.

During a call, press MUTE. The screen displays Muted.

Press MUTE again to resume the conversation. The screen displays

Microphone on briefly.

Call waiting

When you subscribe to call waiting service from your telephone service provider,

you hear an alert tone if there is an incoming call while you are already on a call.

Press FLASH to put the current call on hold and take the new call.

Press FLASH at any time to switch back and forth between calls.

Temporary ringer silencing

When the telephone is ringing, you can temporarily silence the ringer of that handset

without disconnecting the call. The next call rings normally at the preset volume.

Press OFF or MUTE, then displays and Ringer muted displays briefly.

Temporary tone dialing

If you have pulse (rotary) service only, you can switch from pulse to touch-tone

dialing temporarily during a call.

During a call, press TONE .

Use the dialing keys to enter the relevant number. The telephone sends

touch-tone signals.

The telephone automatically returns to pulse dialing mode after you end the call.

Find handset

Use this feature to find all system handsets.

To start paging:

Press FIND HANDSET on the telephone base. All idle

handsets ring and display ** Paging **.

To end paging:

Press FIND HANDSET on the telephone base.

Press , , OFF or any dialing key on a handset.

Place the handset in the telephone base or charger.

Do not press and hold FIND HANDSET for more than four seconds. It may lead to

handset deregistration.

Redial list

Each handset stores the last 10 telephone numbers dialed. When there are already

10 entries, the oldest entry is deleted to make room for the new entry.

To review and dial a number from the redial list:

Press REDIAL when the handset is not in use.

Press , or REDIAL repeatedly until the desired entry displays.

Press or to dial.

To delete a redial entry:

When the desired redial entry displays, press DELETE.

Chain dialing

Use this feature to initiate a dialing sequence from numbers stored in the directory,

caller ID log or redial list while you are on a call. Chain dialing can be useful if you

wish to access other numbers (such as bank account numbers or access codes)

from the directory, caller ID log or redial list.

To access a number in the directory, caller ID log or redial list while on a call:

To enter the directory, press MENU twice.

-OR-

To enter the caller ID log, press MENU then scroll to Caller ID log then

press SELECT.

-OR-

To enter the redial list, press REDIAL.

Scroll to the desired entry.

Press SELECT to dial the displayed number.

Join a call in progress

You can use up to two system handsets at a time on an outside call (for models with

two or more handsets).

When a handset is on a call, press or on another handset to join the call.

Press OFF or place the handset in the telephone base or charger to exit the

call. The call continues until all handsets hang up.

•

Intercom

Use the intercom features for conversations between two handsets.

Press INT on your handset when not in use. When you have three or more

handsets, use the dialing keys to enter a destination handset number.

To answer the intercom call, press , , INT or any dialing key on the

destination handset.

To end the intercom call, press OFF or place the handset back in the telephone

base or charger.

Answer an incoming call during an intercom call

If you receive an outside call during an intercom call, there is an alert tone.

To answer the outside call, press . The intercom call ends automatically.

To end the intercom call without answering the outside call, press OFF. The

intercom call ends and the telephone continues to ring.

Call transfer using intercom

Use the intercom feature to transfer an outside call to another system handset.

During a call, press INT. When you have three or more handsets, use the

dialing keys to enter a destination handset number.

To answer the intercom call, press , , INT or any dialing key on the

destination handset. The outside call is now on hold and both handsets display

Intercom. You can have a private conversation with the destination handset.

From this intercom call, you have the following options:

You can let the destination handset join you on the outside call in a

three-way conversation. Press and hold INT on the originating handset.

You can transfer the call. Press OFF, or place your handset back in the

telephone base or charger. Your handset screen displays Transferred. The

destination handset then automatically connects to the outside call.

You can press INT to switch between the outside call (Outside call displays)

and the intercom call (Intercom displays).

The destination handset can end the intercom call by pressing OFF, or by

placing the handset back in the telephone base or charger. The outside call

continues with the originating handset.

Directory

The directory can store up to 50 entries which are shared by all system handsets.

To add a directory entry:

Enter the number (up to 30 digits) when the handset is not in use then press

SELECT. Then go to Step 3.

-OR-

When the handset is not in use, press MENU then scroll to Directory, and then

press MENU twice.

2. Use the dialing keys to enter the number (up to 30 digits).

-OR-

Copy a number from the redial list by pressing REDIAL and then press , or

REDIAL repeatedly to select a number. Press SELECT to copy the number.

Press SELECT to move on to enter the name.

Use the dialing keys to enter the name (up to 15 characters). Additional key

presses show other characters of that particular key.

Press SELECT to store the entry.

While entering names and numbers, you can:

Press DELETE to backspace and erase a digit or character.

Press and hold DELETE to erase the entire entry.

Press or to move the cursor to the left or right.

Press and hold PAUSE to insert a dialing pause (for entering numbers only).

Press 0 to add a space (for entering names only).

To review and dial a number from the directory:

Entries are sorted alphabetically.

Press when the handset is not in use.

Scroll to browse through the directory, or use the dialing keys to start a

name search.

When the desired entry appears, press or to dial.

To edit a directory entry:

When the desired entry displays, press SELECT.

Use the dialing keys to edit the number, then press SELECT.

Use the dialing keys to edit the name, then press SELECT to confirm.

To delete a directory entry:

When the desired entry displays, press DELETE.

When the screen displays Delete contact?, press SELECT.

•

Speed dial

You can copy up to 9 directory entries into the speed dial locations (0 and 2-9) so

that you can dial these numbers using fewer keys than usual.

To assign a speed dial entry:

Press MENU when the handset is not in use.

Scroll to Directory, then press SELECT.

Scroll to Speed dial, then press SELECT.

Scroll to a desired speed dial location, then press SELECT.

Scroll to a desired directory entry, then press SELECT to save.

To dial a speed dial entry:

Press and hold a dialing key (0 or 2-9) to dial the number stored in the

corresponding location.

To delete a speed dial entry:

Press MENU when the handset is not in use.

Scroll to Directory, then press SELECT.

Scroll to Speed dial, then press SELECT.

Scroll to a desired speed dial location, then press DELETE. The screen

displays Clear SD #X? Press SELECT to confirm.

Caller ID

This product supports caller ID services provided by most telephone service

providers. Depending on your service subscription, you may see the caller’s name,

number, date and time of calls that are sent by your telephone service provider after

the first or second ring.

Caller ID log

The caller ID log stores up to 50 entries. If you answer a call before the caller ID

information displays, it will not be saved in the caller ID log.

The handset displays XX missed calls when you have incoming calls that

have not been answered.

If you want to erase the missed call indicator, press and hold CANCEL on the

idle handset.

To review and dial a number in the caller ID log:

Press CID when the handset is not in use.

Scroll to browse through the caller ID log. When the desired entry appears:

Press # repeatedly to show different dialing options.

Press 1 repeatedly if you need to add or remove 1 in front of the

telephone number.

Press or to dial.

To save a caller ID log entry to the directory:

When the desired caller ID log entry displays, press SELECT.

Use the dialing keys to modify the number, if necessary. Then press SELECT.

Use the dialing keys to modify the name, if necessary. Then press SELECT.

To delete caller ID log entries:

Delete an entry: When the desired caller ID log entry displays, press DELETE.

Delete all entries: Press MENU when the handset is not in use. Scroll

to Caller ID log and then press SELECT. Scroll to Del all calls then press

SELECT twice.

About answering system and voicemail

Your telephone has separate indicators for two different types of voice messages:

those left on the built-in answering system and those left at your telephone service

provider’s voicemail. Each alerts you to new messages differently.

If and XX new messages display on the handsets and the message

window on the telephone base flashes, there are messages recorded on

the built-in answering system. It can record and store up to 99 messages,

depending on the length of each message. Each message can be up to

3 minutes in length. The total storage capacity for the announcement,

messages and memos is approximately 14 minutes.

If and New voicemail display on the handsets, your telephone service

provider is indicating that it has new voicemail for you. Contact your telephone

service provider for more information on how to access your voicemail.

•

Answering system settings

Default settings are indicated by asterisks (*).

Menu setting Description Options

Call screening Set whether you hear the callers while they

are leaving messages to you. Screening: On*

Screening: Off

# of rings Set the number of times the telephone rings

before the answering system answers. 3*; 2; Toll saver;

6; 5; 4;

Remote code Set a two-digit security code to access the

answering system remotely from any touch-

tone telephone.

19*

Msg alert tone Set whether the telephone beeps every

10 seconds to alert you of new messages. Tone: On

Tone: Off*

Recording time Set the recording time for each incoming

message. 3 minutes*

2 minutes

1 minute

Set number of rings

You can set the answering system to answer an incoming call after 2, 3, 4, 5 or 6

rings; or toll saver. If you choose toll saver, the answering system answers a call

after 2 rings when you have new messages, or after 4 rings when you have no

new messages.

Press MENU when the handset is not in use.

Scroll to Answering sys and then press SELECT.

Scroll to Ans sys setup and then press SELECT.

Scroll to # of rings and then press SELECT.

Press or to choose 6, 5, 4, 3, 2 or Toll saver and then press

SELECT to save.

Record your own announcement

You can use the preset announcement to answer calls, or replace it with your own

recorded announcement. The announcement can be up to 90 seconds in length.

Press MENU when the handset is not in use.

Scroll to Answering Sys then press SELECT twice.

The handset announces, “To play, press 2. To record, press 7.”

Then press 7 to record.

The handset announces, “Record after the tone. Press 5 when you are done.”

After the tone, speak towards the handset microphone.

Press 5 when done.

Answering system operation

Turn the answering system on or off

The answering system must be turned on to answer and record messages.

Press ANS ON/OFF on the telephone base to turn the built-in answering

system on or off.

Message playback at the telephone base

Press /PLAY when the phone is not in use.

Options during playback:

Press VOL+ or VOL- to adjust the speaker volume.

Press /SKIP to skip to the next message.

Press /REPEAT to repeat the message currently playing. Press /REPEAT

twice to listen to the previous message.

Press X/DELETE to delete the current message. The system advances to the

next message.

Press /STOP to stop.

Delete all messages at the telephone base

Press X/DELETE twice when the phone is not in use.

Call intercept

If you want to talk to the person whose message is being recorded, press or

on the handset.

Access the answering system remotely

Dial your telephone number from any touch-tone telephone.

When the system plays the announcement, enter the two-digit remote code.

The preset code is 19.

Enter one of the following remote commands.

•

Command Description

1Play all messages.

2Play only new messages.

3Delete the current message (during playback).

33 Delete all old messages.

4Repeat the current message (during playback).

5Stop.

*5 Hear a list of remote commands.

6Skip to the next message (during playback).

*7 Record a new announcement.

8End the call.

0Turn the answering system on or off.

4. Hang up or press 8 to end the call.

Expand your telephone system

You can add new handsets (CS6509/CS6509-14/CS6509-15/CS6509-16,

purchased separately) to your telephone base. Your telephone base supports a

maximum of five handsets.

For more details, refer to the user’s manual that comes with your CS6509/

CS6509-14/CS6509-15/CS6509-16 new handset.

Troubleshooting

If you have difficulty with your telephone, please try the suggestions below.

For customer service, visit our website at www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

My telephone does not work at all.

Make sure the battery is installed and charged correctly. For optimum daily performance,

return the handset to the telephone base or charger after use.

Make sure the power adapter is securely plugged into an outlet not controlled by a

wall switch.

Make sure the telephone line cord is plugged firmly into the telephone base and the

wall jack.

Unplug the electrical power to the telephone base. Wait for approximately 15 seconds,

then plug it back in. Allow up to one minute for the cordless handset and telephone base

to synchronize.

Charge the battery in the handset for up to 11 hours.

If the battery is completely depleted, charge the handset for at least 30 minutes before use.

Remove the battery and then install it again. If that still does not work, it may be necessary

to purchase a new battery.

Disconnect the telephone base from the telephone wall jack and plug in a working

telephone. If the other telephone does not work, the problem is probably in the wiring or the

telephone service. Contact your telephone service provider.

I cannot dial out.

Try all the above suggestions.

Make sure there is a dial tone before dialing. It is normal if the handset takes a second or

two to synchronize with the telephone base before producing a dial tone. Wait an extra

second before dialing.

If other telephones in your home are having the same problem, the problem is in the wiring

or telephone service. Contact your telephone service provider (charges may apply).

Eliminate any background noise. Mute the cordless handset before dialing, or dial from

another room in your home with less background noise.

The display shows To register HS and See manual alternately. The handset

does not work at all.

The handset is deregistered from the telephone base. Place the handset in the telephone

base to register it back. The handset shows Registered and you hear a beep when the

registration process completes. This process takes about 90 seconds to complete.

The answering system does not answer after the correct number of rings.

Make sure the answering system is on. When the answering system is on, the

ANS ON/OFF light on the telephone base should be lit and ANS ON should display on

the handsets.

If toll saver is selected, the number of rings changes to two when there are new

messages waiting.

If the memory is full or if the answering system is off, the answering system answers after

10 rings.

In some cases, the answering system is affected by the ringing system used by your

telephone service provider.

If you subscribe to voicemail service, change the number of rings so that your answering

system answers before your voicemail answers. To determine how many rings activate

your voicemail, please contact your telephone service provider.

If there is a fax machine connected to the same telephone line, try disconnecting the

fax machine. If that solves the problem, consult your fax machine documentation for

information on compatibility with answering systems.

The answering system does not record messages.

Make sure the answering system is on.

When the answering machine memory is full, it does not record new messages until some

old messages are deleted.

If you subscribe to voicemail service, change the number of rings so that your answering

system answers before your voicemail answers. To determine how many rings activate

your voicemail, please contact your telephone service provider.

If there is a fax machine connected to the same telephone line, try disconnecting the

fax machine. If that solves the problem, consult your fax machine documentation for

information on compatibility with answering systems.

The messages on the answering system are incomplete.

If a caller leaves a very long message, part of it may be lost when the answering system

disconnects the call after the preset recording time.

If the memory on the answering system becomes full during a message, the answering

system stops recording and disconnects the call.

If the caller’s voice is very soft, the answering system may stop recording and disconnect

the call.

I have accidentally set my LCD language to Spanish or French, and I don’t

know how to change it back to English.

While the phone is in idle mode or on a call, press MENU once then enter the code 364#.

Common cure for electronic equipment.

If the telephone is not responding normally, put the cordless handset in the telephone base.

If it does not respond, try the following (in the order listed):

1. Disconnect the power to the telephone base.

2. Disconnect the battery on the cordless handset.

3. Wait a few minutes before connecting power to the telephone base.

4. Install the battery again and place the cordless handset in the

telephone base.

5. Wait for the cordless handset to synchronize with the telephone base.

Allow up to one minute for this to take place.

•

Important safety instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk

of fire, electric shock and injury, including the following:

Read and understand all instructions.

Follow all warnings and instructions marked on the product.

Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a

damp cloth for cleaning.

Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or a

swimming pool, or in a wet basement or shower.

Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

Avoid placing the telephone system in places with extreme temperature, direct sunlight, or other electrical

devices. Protect your phone from moisture, dust, corrosive liquids and fumes.

Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation.

To protect them from overheating, these openings must not be blocked by placing the product on a soft

surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat

This product should be operated only from the type of power source indicated on the marking label.

If you are not sure of the type of power supply in your home or office, consult your dealer or local

power company.

Do not allow anything to rest on the power cord. Do not install this product where the cord may be

walked on.

Never push objects of any kind into this product through the slots in the telephone base or handset

because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind

on the product.

To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service

facility. Opening or removing parts of the telephone base or handset other than specified access doors

may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock

when the product is subsequently used.

Do not overload wall outlets and extension cords.

Unplug this product from the wall outlet and refer servicing to an authorized service facility under the

following conditions:

When the power supply cord or plug is damaged or frayed.

If liquid has been spilled onto the product.

If the product has been exposed to rain or water.

If the product does not operate normally by following the operating instructions. Adjust only those

controls that are covered by the operation instructions. Improper adjustment of other controls may

result in damage and often requires extensive work by an authorized technician to restore the

product to normal operation.

If the product has been dropped and the telephone base and/or handset has been damaged.

If the product exhibits a distinct change in performance.

14. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric

shock from lightning.

15. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a

spark may be created when the adapter is plugged into the power outlet, or when the handset is replaced

in its cradle. This is a common event associated with the closing of any electrical circuit. The user should

not plug the phone into a power outlet, and should not put a charged handset into the cradle, if the

phone is located in an environment containing concentrations of flammable or flame-supporting gases,

unless there is adequate ventilation. A spark in such an environment could create a fire or explosion.

Such environments might include: medical use of oxygen without adequate ventilation; industrial gases

(cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.

16. Only put the handset of your telephone next to your ear when it is in normal talk mode.

17. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs

are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

SAVE THESE INSTRUCTIONS

Battery

CAUTION: Use Only Supplied Battery.

Do not dispose of the battery in a fire. Check with local waste management codes for special disposal

instructions.

Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or injury to the

eyes or skin. The electrolyte may be toxic if swallowed.

Exercise care in handling batteries in order not to create a short circuit with conductive materials.

Charge the battery provided with or identified for use with this product only in accordance with the

instructions and limitations specified in this manual.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless telephones):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation

of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by

the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

Should keep wireless telephones at least six inches from the pacemaker.

Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when

it is turned ON.

Should use the wireless telephone at the ear opposite the pacemaker.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using

wireless telephones.

About cordless telephones

Privacy: The same features that make a cordless telephone convenient create some limitations.

Telephone calls are transmitted between the telephone base and the cordless handset by radio

waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio

receiving equipment within range of the cordless handset. For this reason, you should not think of

cordless telephone conversations as being as private as those on corded telephones.

Electrical power: The telephone base of this cordless telephone must be connected to a working

electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made

from the cordless handset if the telephone base is unplugged, switched off or if the electrical power

is interrupted.

Potential TV interference: Some cordless telephones operate at frequencies that may cause

interference to televisions and VCRs. To minimize or prevent such interference, do not place the

telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced,

moving the cordless telephone farther away from the TV or VCR often reduces or eliminates

the interference.

Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with

conducting material such as rings, bracelets, and keys. The battery or conductor may overheat and

cause harm. Observe proper polarity between the battery and the battery charger.

Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not

burn or puncture the battery. Like other batteries of this type, if burned or punctured, they could release

caustic material which could cause injury.

10.

11.

12.

13.

•

Operating range

This cordless telephone operates with the maximum power allowed by the Federal Communications

Commission (FCC). Even so, this handset and telephone base can communicate over only a certain distance

- which can vary with the locations of the telephone base and handset, the weather, and the layout of your

home or office.

When the handset is out of range, the handset displays Out of range or no pwr at base.

If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect well

when you press . Move closer to the telephone base, then press to answer the call.

If the handset moves out of range during a telephone conversation, there may be interference. To improve

reception, move closer to the telephone base.

ECO mode

This power conserving technology reduces power consumption for optimal battery performance, according to

the distance between the telephone base and the handset. When the telephone base communicates with the

handset, ECO mode will be activated automatically.

Maintenance

Taking care of your telephone

Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.

Avoid rough treatment

Place the handset down gently. Save the original packing materials to protect your telephone if you ever need

to ship it.

Avoid water

Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with

wet hands. Do not install the telephone base near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety,

take caution when using electrical appliances during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a

soft cloth slightly dampened with water or mild soap. Do not use excess water or cleaning solvents of any kind.

The RBRC® seal

The RBRC® seal on the nickel-metal hydride battery indicates that

VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these

batteries at the end of their useful lives, when taken out of service within the United States and Canada.

The RBRC® program provides a convenient alternative to placing used nickel-metal hydride batteries into the

trash or municipal waste, which may be illegal in your area.

VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers participating

in the RBRC® program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for

information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this

program is part of its commitment to protecting our environment and conserving natural resources.

RBRC® and

1 (800) 8 BATTERY®

are registered trademarks of Rechargeable Battery Recycling

Corporation.

Remember that electrical appliances can cause serious injury if used when you are wet or standing in

water. If the telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE

POWER CORD AND TELEPHONE LINE CORD FROM THE WALL. Then remove the telephone by the

unplugged cords.

FCC, ACTA and IC regulations

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device

under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended

to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this equipment not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation. Privacy of communications may not be ensured

when using this telephone.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can

be safely absorbed by a user or bystander according to the intended usage of the product. This product has

been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the

user. The telephone base shall be installed and used such that parts of the user’s body other than the hands

are maintained at a distance of approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the

Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment

contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be

provided to your telephone service provider upon request.

The plug and jack used to connect this equipment to premises wiring and the telephone network must comply

with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and

modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is

also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two

lines. See the installation instructions in the user’s manual.

•

The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your

telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th

and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but

not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your

telephone service provider.

This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment

connected to your telephone line, ensure the connection of this equipment does not disable your alarm

equipment. If you have questions about what will disable alarm equipment, consult your telephone service

provider or a qualified installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been

corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized

agents. For repair procedures, follow the instructions outlined under the Limited warranty.

If this equipment is causing harm to the telephone network, the telephone service provider may temporarily

discontinue your telephone service. The telephone service provider is required to notify you before

interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be

given the opportunity to correct the problem and the telephone service provider is required to inform you of

your right to file a complaint with the FCC. Your telephone service provider may make changes in its facilities,

equipment, operation, or procedures that could affect the proper functioning of this product. The telephone

service provider is required to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset, it is hearing aid compatible.

If this product has memory dialing locations, you may choose to store emergency telephone numbers

(e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:

Remain on the line and briefly explain the reason for the call before hanging up.

Perform such activities in off-peak hours, such as early morning or late evening.

Industry Canada

Operation is subject to the following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired

operation.

Privacy of communications may not be ensured when using this phone.

The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical

specifications were met.

The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of

the maximum number of devices allowed to be connected to a telephone interface. The termination on an

interface may consist of any combination of devices subject only to the requirement that the sum of the RENs

of all the devices does not exceed five.

This product meets the applicable Industry Canada technical specifications.

For C-UL compliance only

Mesures de sécurité importantes

Afin de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez toujours ces

mesures préventives de base lorsque vous utilisez votre téléphone :

Lisez et comprenez bien toutes les instructions.

Observez toutes les instructions et mises en garde inscrites sur l’appareil.

Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas de nettoyeurs liquides ni

en aérosol. N’utilisez qu’un chiffon doux et légèrement humecté.

N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier de cuisine, d’un bac

de lavage ou d’une piscine, ou dans un sous-sol humide ou sous la douche.

Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil pourrait tomber et

être sérieusement endommagé.

Évitez d’installer le système téléphonique dans les endroits soumis à une température extrême, à la lumière

directe du soleil ou à proximité immédiate d’autres appareils électriques ou électroniques. Protégez votre

téléphone contre les sources d’humidité, la poussière, les vapeurs et les liquides corrosifs.

Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière ou en dessous. Afin

d’empêcher la surchauffe, ces ouvertures ne doivent pas être obstruées en plaçant l’appareil sur un lit, divan,

tapis ou autre surface similaires. Ne placez pas cet appareil à proximité d’un élément de chauffage ni d’une

plinthe électrique. De plus, ne l’installez pas dans une unité murale ou un cabinet fermé qui ne possède pas

d’aération adéquate.

Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les étiquettes de l’appareil.

Si vous ne connaissez pas le voltage de votre maison, consultez votre marchand ou votre fournisseur

d’électricité.

Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit sécuritaire, là où

personne ne pourra trébucher sur la ligne d’alimentation ni le cordon téléphonique modulaire.

N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils pourraient toucher à

des points de tension dangereux ou court-circuiter des pièces, ce qui constituerait un risque d’incendie ou

d’électrocution. N’échappez pas de liquides dans l’appareil.

Afin de réduire les risques d’électrocution, ne démontez pas l’appareil, mais apportez-le plutôt à un

centre de service qualifié s’il doit être réparé. En enlevant le couvercle, vous vous exposez à des

tensions dangereuses ou autres dangers similaires. Un remontage inadéquat peut être à l’origine d’une

électrocution lors d’une utilisation ultérieure de l’appareil. Débranchez l’appareil avant de procéder au

nettoyage. Utilisez un chiffon humide et doux.

Ne surchargez pas les prises de courant et les rallonges.

Débranchez cet appareil de la prise de courant et communiquez avec le département de service à la

clientèle de VTech dans les cas suivants:

Lorsque le cordon d’alimentation est endommagé ou écorché.

Si du liquide a été échappé dans l’appareil.

Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.

Si le produit ne fonctionne pas normalement en respectant les instructions de fonctionnement. Réglez

uniquement les commandes indiquées dans le les instructions de fonctionnement. Les réglages

incorrects des autres commandes pourraient provoquer un dommage qui pourrait exiger un travail

exhaustif de la part d’un technicien autorisé afin de rétablir le fonctionnement normal de l’appareil.

Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.

Si le produit affiche une nette diminution de sa performance.

14. Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant un orage. Les éclairs peuvent être à l’origine

d’une électrocution.

15. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite. En certaines

circonstances, une flammèche pourrait être provoquée lorsque l’adaptateur est branché à une prise de

courant, ou lorsque le combiné est déposé sur le socle. Ceci est un événement commun associé à la

fermeture d’un circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à une prise de courant,

et ne devrait pas déposer le combiné chargé sur le socle, si le téléphone se trouve à proximité d’un

endroit comportant des concentrations de gaz inflammables, à moins que la ventilation soit adéquate. Une

flammèche dans un tel endroit pourrait provoquer un incendie ou une explosion. De tels environnements

peuvent comprendre: des endroits où l’on utilise de l’oxygène médical sans ventilation adéquate; des gaz

industriels (dissolvants de nettoyage, des vapeurs d’essence, etc.); une fuite de gaz naturel, etc.

10.

11.

12.

13.

•

16. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode de conversation.

17. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au sol. Les broches ne sont

pas conçues pour maintenir l’adaptateur en place si celui-ci est barnché dans une prise au plafond ou sous

une table/ armoire.

CONSERVEZ CES INSTRUCTIONS

Pile

MISE EN GARDE : N’utilisez que la pile incluse.

Ne jetez pas la pile au feu. Vérifiez les instructions spécifiques de mise aux rebus auprès des autorités

locales.

N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif et pourrait causer

des brûlures ou des blessures aux yeux ou à la peau. L’électrolyte est toxique si avalé.

Soyez prudents lorsque vous manipulez les piles afin d’éviter les courts-circuits provoqués par des

matériaux conducteurs. .

Rechargez la pile incluse ou identifiée pour fonctionner avec cet appareil, selon les instructions et limites

spécifiées dans ce guide d’utilisation.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans fil) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené

une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs

cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des

États-Unis, la firme WTR recommande aux médecins :

Avis aux détenteurs de stimulateurs cardiaques

Ils doivent tenir le téléphone sans fil à une distance d’au moins six pouces du stimulateur cardiaque.

Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une

poche de chemise, lorsque celui-ci est en marche.

Ils doivent utiliser le téléphone sans fil en l’appuyant sur l’oreille qui se trouve dans la direction opposée

au stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs

cardiaques causés par les gens qui utilisent un téléphone sans fil à proximité de ceux-ci.

À propos des téléphones sans l

Condentialité : Les mêmes caractéristiques qui constituent des avantages pour les téléphones sans

fil affichent également des restrictions. Les appels téléphoniques sont transmis entre le combiné sans

fil et le socle par le biais d’ondes radio ; il y a donc la possibilité que vos conversations téléphoniques

sans fil soient interceptées par des équipements de réception radio se trouvant dans la portée du

combiné sans fil. Pour cette raison, vous ne devez pas percevoir les communications téléphoniques

sans fil comme étant aussi confidentielles que celles des téléphones à cordons.

Alimentation électrique : Le socle de ce téléphone sans fil doit être branché à une prise électrique

fonctionnelle. La prise électrique ne doit pas être contrôlée par un interrupteur mural. Les appels ne

pourront pas être effectués du combiné sans fil si le socle est débranché ou mis hors tension ou si le

courant est coupé.

Possibilité d’interférences aux téléviseurs : Certains téléphones sans fil fonctionnent sur des

fréquences pouvant causer des interférences aux téléviseurs et aux magnétoscopes. Pour réduire ou

prévenir de telles interférences, ne placez pas le socle du téléphone sans fil près ou sur un téléviseur

ou magnétoscope. S’il y a présence de parasites, il est conseillé d’éloigner le téléphone sans fil du

téléviseur ou du magnétoscope afin de réduire possiblement les interférences.

Piles rechargeables : Manipulez les piles avec soin afin de ne pas les court-circuiter avec des bagues,

bracelets ou clés. Les piles ou le conducteur peut surchauffer et causer des blessures. Respectez la

polarité adéquate entre la pile et le chargeur.

Les bloc-piles rechargeables à l’hydrure métallique de nickel : Jetez ces blocs-piles de manière

écologique et sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les autres piles de ce type,

elles pourraient dégager une matière toxique qui peut causer des blessures corporelles si elles sont

brûlées ou percées.

•

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or

“you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects

in material and workmanship, pursuant to the following terms and conditions, when installed and used

normally and in accordance with the Product operating instructions. This limited warranty extends only to the

Consumer for Products purchased and used in the United States of America and Canada.

What will VTech do if the Product is not free from defects in materials and workmanship during the

limited warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service representative will repair or replace at

VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new

or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or

refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment.

Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the

repaired or replacement Products to you in working condition. You should expect the repair or replacement

to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech

repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited

warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date

the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year

warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper

installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration or modification by anyone other than an

authorized service representative of VTech; or

3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or

cable or antenna systems; or

4. Product to the extent that the problem is caused by use with non-VTech accessories; or

5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have

been removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or

Canada, or used for commercial or institutional purposes (including but not limited to Products used for

rental purposes); or

7. Product returned without a valid proof of purchase (see item 2 below); or

8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems

outside the unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and

features may save you a service call.

Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and

are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location.

VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling

charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure

is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty,

VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity.

You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by

this limited warranty.

What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech service location along

with a description of the malfunction or difficulty; and

2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and

the date of purchase or receipt; and

3. Provide your name, complete and correct mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other

written or oral communications related to this Product. VTech provides no other warranties for this Product.

The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other

express warranties. No one is authorized to make modifications to this limited warranty and you should not

rely on any such modification.

State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights,

which vary from state to state or province to province.

Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an

unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase.

Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation

may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential,

or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other

associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use

of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof of purchase.

Technical specications

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Handset: 1921.536-1928.448 MHz

Telephone base: 1921.536-1928.448MHz

Channels 5

Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary

according to environmental conditions at the time of use.

Power requirements Handset: 2.4V Ni-MH battery

Telephone base: DC 6V @ 400mA

Charger: DC 6V @ 400mA

Memory Handset directory:

50 memory locations; up to 30 digits and 15 characters

Handset caller ID log:

50 memory locations; up to 24 digits and 15 characters

Designed to fit your home.

And your life.

VTech Communications, Inc.

A member of THE VTECH GROUP OF COMPANIES.

VTech is a registered trademark of VTech Holdings Limited.

Specifications are subject to change without notice.

Document order number: 91-007080-070-100

VTech CS6529 Manuel utilisateur

Marque: VTech

Modèle: CS6529

Catégorie: Téléphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech CS6529 User manual

VTech CS6529 Manuel utilisateur

VTech CS6529 Manuel utilisateur

dans d''autres langues

Documents connexes