VTech CS6529 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur

Ce manuel convient également à

Telephone base
3
1
2
4
5
7
9
6
8
1 – X/DELETE
Press to delete the message currently playing.
When the phone is not in use, press twice to
delete all previously reviewed messages.
2 – /SKIP
Press to skip to the next message.
3 – Message window
Shows the number of messages, and other
information of the answering system or
telephone base.
4 – /PLAY/STOP
Press to play messages.
Press to stop message playback.
5 – VOL+ / VOL-
Press to adjust the volume during message
playback.
When the phone is not in use, press to adjust the
telephone base ringer volume.
6 – /REPEAT
Press to repeat the playing message.
Press twice to play the previous message.
7 –
Page all system handsets.
8 – light
Steady on in red when the line is in use or when
a handset is being registered.
Flashes in red when there is an incoming call or
when handsets are being deregistered.
Refer to the Bluetooth section for the IN USE light
indications when pairing and using a Bluetooth
headset.
9 – ANS ON/OFF
Press to turn the answering system on or off.
Handset
1
7
2
3
4
6
5
8
9
10
11
1 – /
Review the directory when the phone is not
in use.
Scroll up while in a menu, or in the directory,
caller ID log or redial list.
Move the cursor to the right when entering
numbers or names.
Increase the listening volume during a call or
message playback.
/
Review the caller ID log when the telephone is
not in use.
Scroll down while in a menu, or in the
directory, caller ID log or redial list.
Move the cursor to the left when entering
numbers or names.
Decrease the listening volume during a call or
message playback.
2 –
Show the menu.
While in a menu, press to select an item, or save
an entry or setting.
3 –
Hang up a call.
Return to the previous menu.
Press and hold to exit menu display without
making changes.
Delete digits while predialing.
Silence the handset ringer temporarily while the
phone is ringing.
Press and hold to erase the missed call indicator
while the handset is not in use.
4 –
Press and hold to turn on or off the quiet mode.
Press repeatedly to show other dialing options
when reviewing a caller ID log entry.
5 –
Press to start an intercom conversation or
transfer a call (for multi-handset models only).
6 –
Mute the microphone during a call.
Silence the handset ringer temporarily while the
phone is ringing.
Delete the displayed entry while reviewing the
directory, caller ID log, or redial list.
Delete digits or characters when entering
numbers or names.
7 – light
On when the handset is charging.
8 –
Review the last 10 numbers dialed.
Press and hold to insert a dialing pause while
dialing or entering numbers into the directory.
9 –
Make or answer a call.
Answer an incoming call when you receive a
call waiting alert.
10 – Dialing keys
Press repeatedly to add or remove 1 in front of
the caller ID log entry before dialing or saving
it to the directory.
Press and hold to set or dial your voicemail
number.
Switch to tone dialing temporarily during a call.
Press to add a space when entering names.
11 –
Make or answer a call using the handset
speakerphone.
During a call, press to switch between the
speakerphone and the handset earpiece.
Display icons
The battery icon flashes when the
battery is low and needs charging.
The battery icon animates when the
battery is charging.
The battery icon becomes solid
when the battery is fully charged.
The handset ringer is turned off.
There are new voicemail received
from your telephone service
provider.
NEW The entry you are reviewing is new
in the caller ID log.
ANS ON The answering system is turned on.
10/16
MSG #MSG # The message number currently
playing and the total number of
messages.
Use the handset menu
1. Press MENU when the phone is not in use.
2. Press q or p until the screen displays the
desired feature menu.
3. Press SELECT.
Press CANCEL to return to the previous menu.
Press and hold CANCEL to exit completely.
Make a call
Press or , and then dial the telephone
number.
Answer a call
Press , or any dialing keys.
End a call
Press OFF or put the handset back in the
telephone base or charger.
Speakerphone
During a call, press on the handset to switch
between speakerphone and handset earpiece.
Volume
During a call, press p/VOLUME/q to adjust
the listening volume.
Mute
The mute function allows you to hear the other party
but the other party cannot hear you.
1. During a call, press MUTE. The handset displays
Muted.
2. Press MUTE again to resume the conversation.
The handset displays Microphone on briefly.
Join a call in progress (for two-handset
models only)
You can use up to two handsets at a time on an
outside call.
When a handset is already on a call, press
or on another handset to join the call.
To exit the call, press OFF on the handset or
place it in the telephone base or charger. The
call continues until all handsets hang up.
Call waiting
When you subscribe to call waiting service from
your telephone service provider, you hear an
alert tone if there is an incoming call while you are
already on a call.
Press FLASH to put the current call on hold and
take the new call.
Press FLASH at any time to switch back and
forth between calls.
Find handset
Use this feature to find the system handset.
To start paging:
Press FIND HANDSET on the telephone base
when not in use. All idle handsets ring and
display ** Paging **.
To end paging:
Press FIND HANDSET at the telephone base.
-OR-
Press , , OFF or any dialing keys on the
handset.
-OR-
Place the handset in the telephone base or
charger.
NOTE: Do not press and hold FIND HS
for more than 4 seconds. It may lead to
handset deregistration.
Bluetooth®
Your telephone system is enhanced with
Bluetooth feature. You can pair a Bluetooth
headset to your telephone system and answer
calls with your Bluetooth headset.
NOTES:
Before you begin, make sure that your
Bluetooth enabled headset is not connected
to any other Bluetooth device. If you have
trouble pairing your Bluetooth headset to
your telephone system, try turning off the
Bluetooth feature of the nearby devices
that your Bluetooth headset has previously
paired.
Bluetooth wireless technology operates within
a short range (a maximum of approximately
15 feet) from the telephone base. Keep
connected headset within this range.
For more details about the Bluetooth feature,
read the online Complete user’s manual.
Pair and connect a Bluetooth headset
1. Set your Bluetooth headset to pairing mode.
Refer to your Bluetooth headset user’s manual
to learn how.
2. Press or on the handset.
3. Press and hold FIND HANDSET on the
telephone base for 4 seconds.
The telephone then enters pairing mode.
The IN USE LED flashes in purple and red
alternately.
To cancel pairing, press FIND HANDSET on
the telephone base.
4. When successfully paired and connected to the
Bluetoooth headset, the IN USE LED becomes
steady on in purple.
5. Press OFF on the handset or place the handset
in the telephone base or charger after pairing.
The IN USE LED becomes steady on in blue.
Bluetooth headset connection status:
Pairing - while pairing to a Bluetooth headset,
the IN USE LED flashes in purple and red
alternately.
Connected - when successfully paired and
connected to a Bluetooth headset, the IN USE
LED becomes steady on in blue when the
telephone is not in use.
NOTE: When there is an incoming call, you hear
a ringing tone on your Bluetooth headset and
the IN USE LED flashes in red. You can answer
the incoming call with your Bluetooth headset.
Bluetooth headset in use - when the
connected Bluetooth headset is in use, the IN
USE LED flashes in purple and blue alternately.
Both telephone and Bluetooth headset are
in use - when both the telephone and the
connected Bluetooth headset are in use, the IN
USE LED becomes steady on in purple.
No connection - the IN USE LED turns off.
Remove paired Bluetooth headset
1. Press or on the handset.
2. Press and hold FIND HANDSET on the
telephone base for 4 seconds. The paired
Bluetooth headset will be removed.
NOTES:
You can use your connected Bluetooth
headset to answer calls or end the call.
If you fail to connect your Bluetooth headset
to the telephone, re-try the pairing steps
above.
To pair another Bluetooth headset to the
telephone, perform the pairing steps above
and the current paired headset will be
replaced by the new Bluetooth headset.
While on a call using your Bluetooth headset,
keep your headset closer to the telephone
base (within 15 feet) and make sure that
there are no physical obstacles such as large
furniture or thick wall in between.
The Bluetooth® word mark and logos are owned by Bluetooth
SIG, Inc. and any use of such marks by Advanced American
Telephones and its parent, VTech Holdings Limited, is under
license. VTech Holdings Limited is a member of Bluetooth
SIG, Inc. Other trademarks and trade names are those of their
respective owners.
When using your telephone equipment, basic safety
precautions should always be followed to reduce the risk of
fire, electric shock and injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the
product.
3. Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth
for cleaning.
4. CAUTION: Do not install the telephone base at a height
above 2 meters.
5. Do not use this product near water such as near a bath tub,
wash bowl, kitchen sink, laundry tub or a swimming pool,
or in a wet basement or shower.
6. Do not place this product on an unstable table, shelf,
stand or other unstable surfaces.
7. Avoid placing the telephone system in places with extreme
temperature, direct sunlight, or other electrical devices.
Protect your phone from moisture, dust, corrosive liquids
and fumes.
8. Slots and openings in the back or bottom of the telephone
base and handset are provided for ventilation. To protect
them from overheating, these openings must not be
blocked by placing the product on a soft surface such as
a bed, sofa or rug. This product should never be placed
near or over a radiator or heat register. This product should
not be placed in any area where proper ventilation is not
provided.
9. This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supply in your home or
office, consult your dealer or local power company.
10. Do not allow anything to rest on the power cord. Do not
install this product where the cord may be walked on.
11. Never push objects of any kind into this product through
the slots in the telephone base or handset because they
may touch dangerous voltage points or create a short
circuit. Never spill liquid of any kind on the product.
12. To reduce the risk of electric shock, do not disassemble
this product, but take it to an authorized service facility.
Opening or removing parts of the telephone base or
handset other than specified access doors may expose
you to dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when the product
is subsequently used.
13. Do not overload wall outlets and extension cords.
14. Unplug this product from the wall outlet and refer
servicing to an authorized service facility under the
following conditions:
When the power supply cord or plug is damaged or
frayed.
• If liquid has been spilled onto the product.
• If the product has been exposed to rain or water.
If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operation instructions. Improper
adjustment of other controls may result in damage
and often requires extensive work by an authorized
technician to restore the product to normal operation.
If the product has been dropped and the telephone
base and/or handset has been damaged.
If the product exhibits a distinct change in performance.
15. Avoid using a telephone (other than cordless) during an
electrical storm. There is a remote risk of electric shock
from lightning.
16. Do not use the telephone to report a gas leak in the
vicinity of the leak. Under certain circumstances, a spark
may be created when the adapter is plugged into the
power outlet, or when the handset is replaced in its
cradle. This is a common event associated with the
closing of any electrical circuit. The user should not
plug the phone into a power outlet, and should not
put a charged handset into the cradle, if the phone is
located in an environment containing concentrations
of flammable or flame-supporting gases, unless there
is adequate ventilation. A spark in such an environment
could create a fire or explosion. Such environments
might include: medical use of oxygen without adequate
ventilation; industrial gases (cleaning solvents; gasoline
vapors; etc.); a leak of natural gas; etc.
17. Only put the handset of your telephone next to your ear
when it is in normal talk mode.
18. The power adapter is intended to be correctly oriented
in a vertical or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
19. For pluggable equipment, the socket-outlet shall
be installed near the equipment and shall be easily
accessible.
20. CAUTION: Use only the batteries indicated
in this manual. There may be a risk of
explosion if a wrong type of battery is used for the
handset. Use only the supplied rechargeable batteries
or replacement batteries for the handset. Do not
dispose of batteries in a fire. They may explode.
Disposed of used batteries according to the instruction.
Do not use the battery in following conditions:
»High or low extreme temperature during use,
storage or transportation.
»Replacement of a battery with an incorrect type
that can defeat a safeguard.
»Disposal of a battery into fire or a hot oven, or
mechanically crushing or cutting of a battery, that
can result in an explosion.
»Leaving a battery in an extremely high
temperature surrounding environment that can
result in an explosion or the leakage of flammable
liquid or gas.
»A battery subjected to extremely low air pressure
that can result in an explosion or the leakage of
flammable liquid or gas.
21. Use only the adapter included with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
22. The applied nameplate is located at the bottom or near
of the product.
SAVE THESE INSTRUCTIONS
Battery
Use only the battery provided or equivalent. To order a
replacement, visit our website at
www.vtechphones.com or call 1 (800) 595-9511. In
Canada, go to phones.vtechcanada.com or call
1 (800) 267-7377.
Do not dispose of the battery in a fire. Check with
local waste management codes for special disposal
instructions.
Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause burns or injury
to the eyes or skin. The electrolyte may be toxic if
swallowed.
Exercise care in handling batteries in order not to create
a short circuit with conductive materials.
Charge the battery provided with this product only
in accordance with the instructions and limitations
specified in this manual.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless
telephones):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless telephones and
implanted cardiac pacemakers. Supported by the U.S. Food
and Drug Administration, WTR recommends to physicians
that:
Pacemaker patients
Should keep wireless telephones at least six inches from
the pacemaker.
Should NOT place wireless telephones directly over
the pacemaker, such as in a breast pocket, when it is
turned ON.
Should use the wireless telephone at the ear opposite
the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless telephones.
About cordless telephones
Privacy: The same features that make a cordless
telephone convenient create some limitations.
Telephone calls are transmitted between the telephone
base and the cordless handset by radio waves, so
there is a possibility that the cordless telephone
conversations could be intercepted by radio receiving
equipment within range of the cordless handset. For
this reason, you should not think of cordless telephone
conversations as being as private as those on corded
telephones.
Electrical power: The telephone base of this cordless
telephone must be connected to a working electrical
outlet. The electrical outlet should not be controlled by
a wall switch. Calls cannot be made from the cordless
handset if the telephone base is unplugged, switched
off or if the electrical power is interrupted.
Potential TV interference: Some cordless telephones
operate at frequencies that may cause interference
to televisions and VCRs. To minimize or prevent such
interference, do not place the telephone base of the
cordless telephone near or on top of a TV or VCR.
If interference is experienced, moving the cordless
telephone farther away from the TV or VCR often
reduces or eliminates the interference.
Rechargeable batteries: Exercise care in handling
batteries in order not to create a short circuit with
conducting material such as rings, bracelets and keys.
The battery or conductor may overheat and cause harm.
Observe proper polarity between the battery and the
battery charger.
Nickel-metal hydride rechargeable batteries: Dispose
of these batteries in a safe manner. Do not burn or
puncture the battery. Like other batteries of this type,
if burned or punctured, they could release caustic
material which could cause injury.
Go to www.vtechphones.com (US) to register your
product for enhanced warranty support and latest
VTech product news.
Go to phones.vtechcanada.com (Canada) for the latest
VTech product news.
Specifications are subject to change without notice.
© 2023 VTech Communications, Inc. |
© 2023 VTech Technologies Canada Ltd.
All rights reserved. 12/23.
CS6529-X_BT_HS59VSD-BS56VSD_US-CAN_ACIB_V1_231214
BT_HS59VSD-BS56VSD
What’s in the box Setup
Overview
After the telephone is installed or power returns
following a power outage and battery depletion,
the handset will prompt you to set the date and
time.
Date and time
When the handset prompts, follow the steps below
to set the date and time.
1. Use the dialing keys (0-9) to enter the month
(MM), date (DD) and year (YY). Then press
SELECT.
2. Use the dialing keys (0-9) to enter the hour
(HH) and minute (MM). Then press q or p to
choose AM or PM.
3. Press SELECT to save.
NOTE: If you have skipped the prompt,
you can set up again by pressing MENU.
Scroll to choose Set date/time and press
SELECT. Then, follow the steps above.
Change LCD language settings
You can select English, French, or Spanish to be
used in all screen displays:
1. Press MENU when the handset is not in use.
2. Press q or p to scroll to Settings and then
press SELECT.
3. Press SELECT to choose LCD language.
4. Press q or p to choose English, Français or
Español, and then press SELECT twice to save.
NOTE: If you accidentally set the LCD
language to Spanish or French, press
MENU and then enter *364# to change
the handset LCD language back to
English while the handset is not in use.
Important safety instructions
Redial list
Each handset stores the last 10 telephone numbers
dialed. When there are already 10 entries, the
oldest entry is deleted to make room for the new
entry.
Review and dial a redial list entry
1. Press REDIAL when the handset is not in use.
2. Press q, p or REDIAL repeatedly until the
desired entry displays.
3. Press or to dial.
Delete a redial list entry
When the desired redial entry displays, press
DELETE.
Transfer a call
While on an outside call, you can transfer the call
from one handset to another.
1. Press MENU on your handset during a call.
2. Press q or p to scroll to Transfer, and then
press SELECT.
3. If you have three or more handsets, use the
dialing keys to enter a destination handset
number.
4. To answer the intercom call, press , or any
dialing key on the destination handset.
Intercom
Use the intercom features for conversations
between two handsets.
1. Press INT on your handset when not in use.
If you have three or more handsets, use the
dialing keys to enter a destination handset
number.
2. To answer the intercom call, press , , INT
or any dialing key on the destination handset.
3. To end the intercom call, press OFF or place the
handset back in the telephone base or charger.
Answer an incoming call during an intercom
call
If you receive an incoming call during an intercom
call, there is an alert tone.
To answer the outside call, press . The
intercom call ends automatically.
To end the intercom call without answering
the outside call, press OFF. The telephone
continues to ring.
Call transfer using intercom
While on an outside call, you can use the intercom
feature to transfer the call from one handset to
another.
1. Press INT on your handset during a call. The
current call is put on hold.
If you have three or more handsets, use the
dialing keys to enter a destination handset
number.
2. To answer the intercom call on the destination
handset, press , , INT or any dialing key on
the destination handset. You can now have a
private conservation before transferring the call.
3. From this intercom call, you have the following
options:
You can let the destination handset join
you on the outside call in a three-way
conversation. Press and hold INT on the
originating handset.
You can transfer the call. Press OFF, or place
your handset back in the telephone base
or charger. The destination handset is then
connected to the outside call.
You can press INT to switch between the
outside call (Outside call displays) and the
intercom call (Intercom displays).
The destination handset can end the
intercom call by pressing OFF, or by placing
the handset back in the telephone base or
charger. The outside call continues with the
original system handset.
Directory
The directory can store up to 50 entries, which are
shared by all handsets. Each entry may consist of a
telephone number up to 30 digits, and a name up
to 15 characters.
Add a directory entry
1. Enter the number when the phone is not in use.
Press MENU, then go to Step 3.
-OR-
Press MENU when the phone is not in use.
Scroll to Directory and then press SELECT. Press
SELECT again to choose Add contact.
2. Use the dialing keys to enter the number.
-OR-
Copy a number from the redial list by pressing
REDIAL and then press q, p or REDIAL
repeatedly to select a number. Press SELECT to
copy the number.
3. Press SELECT to move on to enter the name.
4. Use the dialing keys to enter the name.
Additional key presses show other characters of
that particular key.
5. Press SELECT to save.
While entering names and numbers, you can:
Press DELETE to backspace and erase a digit or
character.
Press and hold DELETE to erase the entire entry.
Press q or p to move the cursor to the left or
right.
Press and hold PAUSE to insert a dialing pause
(for entering numbers only).
Press 0 to add a space (for entering names
only).
Review a directory entry
Entries are sorted alphabetically.
1. Press when the phone is not in use.
2. Scroll to browse through the directory, or use
the dialing keys to start a name search.
-OR-
1. Press MENU when the phone is not in use.
2. Scroll to Directory, and then press SELECT.
3. Scroll to Review, and then press SELECT.
4. Scroll to browse through the directory.
Delete a directory entry
1. When the desired entry displays, press DELETE.
2. When the handset displays Delete contact?,
press SELECT.
Edit a directory entry
1. Search for or review the directory entries (see
Review a directory entry).
2. When the desired entry displays, press SELECT.
3. Use the dialing keys to edit the number, then
press SELECT.
4. Use the dialing keys to edit the name, then
press SELECT.
Dial a directory entry
1. Search for or review the directory entries (see
Review a directory entry).
2. When the desired entry appears, press or
to dial.
Speed dial
You can copy up to 9 directory entries into the
speed dial locations (0 and 2-9) so that you can dial
these numbers using fewer keys than usual.
The speed dial memory locations are stored in the
telephone base and are shared by all handsets.
Changes made to the speed dial entries on one
handset apply to all.
Assign a speed dial entry
1. Press MENU when the phone is not in use.
2. Scroll to Directory, and then press SELECT.
3. Scroll to Speed dial, and then press SELECT.
4. Press q or p or the dialing keys (0 or 2-9) to
choose the desired speed dial location.
5. Press SELECT. The screen displays Copy from
DIR... and then the first entry in the directory.
6. Scroll to browse to the desired entry.
-OR-
Use the alphabetical search to find the desired
entry.
7. Press SELECT to save. You hear a confirmation.
The name (up to 12 characters) appears in the
selected speed dial location.
NOTES:
If the directory is empty, when you press
SELECT in Step 5, the screen displays
Directory empty.
If the speed dial location you selected
is occupied, the new directory entry
you selected replaces the old one. Take
caution not to replace entries you do
not wish to delete from the speed dial
locations.
Reassign a speed dial entry
1. Press MENU when the phone is not in use.
2. Scroll to Directory, and then press SELECT.
3. Scroll to Speed dial, and then press SELECT.
4. Press q or p or the dialing keys (0 or 2-9) to
choose the speed dial location you want to
reassign.
5. Press SELECT twice. The screen displays
Reassign SD.
6. Press SELECT. The screen displays Copy from
DIR... and then the first entry of the directory.
7. Scroll to browse to the desired entry.
-OR-
Use the alphabetical search to find the desired
entry.
8. Press SELECT to save. You hear a confirmation.
The name (up to 12 characters) appears in the
selected speed dial location.
Dial a speed dial number
Press and hold a dialing key (0 or 2-9) to dial the
number stored in the corresponding speed dial
location.
When the speed dial location is empty, the screen
displays the speed dial list. See Assign a speed dial
entry to add a new entry.
Delete a speed dial entry
1. Press MENU when the phone is not in use.
2. Scroll to Directory, and then press SELECT.
3. Scroll to Speed dial, and then press SELECT.
4. Press q or p or the dialing keys (0 or 2-9) to
choose the desired speed dial location, then
press DELETE. The screen displays Clear SD #X?.
5. Press SELECT to confirm. You hear a confirmation
tone.
NOTE:
Deleting the speed dial entries does not
affect the entries in the directory.
CS6529
CS6529-14
CS6529-15
CS6529-16
CS6529-17
CS6529-19
CS6529-2
CS6529-25
CS6529-26
CS6529-3
CS6529-4
CS6529-4B
CS6529-5
Abridged user’s manual
Scan the QR code for
support information
(US)
(CA)
Your telephone package contains the following
items. Save your sales receipt and original packaging
in case it is necessary to ship your telephone for
warranty service.
Abridged
user’s
manual
1 set for CS6529-2/
CS6529-25/CS6529-26 |
2 sets for CS6529-3 |
3 sets for CS6529-4/
CS6529-4B
4 sets for CS6529-5
1 set for CS6529/
CS6529-14/CS6529-15/
CS6529-16/CS6529-17/
CS6529-19 |
2 sets for CS6529-2/
CS6529-25/CS6529-26 |
3 sets for CS6529-3 |
4 sets for CS6529-4/
CS6529-4B
5 sets for CS6529-5
Install and Connect | Mount (optional)
Install the battery
Connect and charge
Connect the telephone base
If you subscribe to digital subscriber line (DSL)
high-speed Internet service through your
telephone line, make sure you connect a DSL
filter (not included) to the telephone wall jack.
Mount (optional)
a
Remove the telephone line cord
from the telephone wall jack, and the
telephone base power adapter from
the electrical outlet (if necessary).
c
b
Position the telephone base against the wall
mount bracket with the extended tabs marked B
on top. Insert the extended tabs marked B on the
wall mount bracket into the slots marked B on the
back of the telephone base. Push the telephone
base down until it clicks securely.
d
12
3
1
2
CHARGE light
remains on
when charging.
2
3
1
Telephone operations
The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by
Advanced American Telephones and its parent, VTech Holdings Limited, is under license. VTech Holdings
Limited is a member of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective
owners.
Caller ID
If you subscribe to caller ID service, information
about each caller appears after the first or
second ring. If you answer a call before the caller
information appears on the screen, it will not be
saved in the caller ID log.
The caller ID log stores up to 50 entries. Each entry
has up to 24 digits for the phone number and 15
characters for the name.
If the telephone number has more that 15 digits,
only the last 15 digits appear. If the name has more
than 15 characters, only the first 15 characters are
shown and saved in the caller ID log.
Review a caller ID log entry
1. Press CID when the phone is not in use.
2. Scroll to browse through the caller ID log.
-OR-
1. Press MENU when the phone is not in use.
2. Scroll to Caller ID log, and then press SELECT.
3. Press SELECT to choose Review.
4. Scroll to browse through the caller ID log.
Press # or 1 repeatedly if you need to add or
remove 1 in front of the phone number.
Missed call indicator
When there are calls that have not been reviewed
in the caller ID log, the handset displays XX missed
calls.
Each time you review a caller ID log entry marked
NEW, the number of missed calls decreases by
one.
When you have reviewed all the missed calls, the
missed call indicator no longer displays.
If you do not want to review the missed calls
one by one, press and hold CANCEL on the idle
handset to erase the missed call indicator. All the
entries are then considered old.
Dial a caller ID log entry
1. Search for or review the caller ID log entries
(see Review a caller ID log entry).
2. When the desired entry appears, press or
to dial.
Save a caller ID log entry to the directory
1. Search for or review the caller ID log entries
(see Review a caller ID log entry).
2. When the desired caller ID log entry displays,
press SELECT.
3. Use the dialing keys to edit the number, if
necessary. Then press SELECT.
4. Use the dialing keys to edit the name, if
necessary. Then press SELECT.
Delete the caller ID log entries
1. Search for or review the caller ID log entries
(see Review a caller ID log entry).
2. When the desired caller ID log entry displays,
press DELETE.
To delete all caller ID log entries:
1. Press MENU when the phone is not in use.
2. Scroll to Caller ID log and then press SELECT.
3. Scroll to Del all calls and then press SELECT.
4. Press SELECT to confirm.
Sound settings
Key tone
You can turn the key tone on or off.
1. Press MENU when the handset is not in use.
2. Scroll to Settings and then press SELECT.
3. Scroll to choose Key tone, then press SELECT.
4. Press q or p to choose Key tone:On or Key
tone:Off, then press SELECT to save.
Ringer tone
You can choose from different ringer tones for
each handset.
1. Press MENU when the handset is not in use.
2. Scroll to Ringers and then press SELECT.
3. Scroll to choose Ringer tone, then press
SELECT.
4. Press q or p to sample each ringer tone, then
press SELECT to save.
NOTE: If you turn off the ringer volume,
you will not hear ringer tone samples.
Ringer volume
You can adjust the handset ringer volume level, or
turn the ringer off.
1. Press MENU when the handset is not in use.
2. Scroll to Ringers and then press SELECT.
3. Press SELECT again to choose Ringer volume.
4. Press q or p to sample each volume level,
then press SELECT to save.
NOTES:
If you turn off the volume, the handset
will be silenced and display icon.
When the ringer volume is set to Off,
the handset still rings when you press
FIND HANDSET at the telephone base.
Temporary ringer silencing
When the telephone is ringing, you can temporarily
silence the ringer without disconnecting the call. The
next call rings normally at the preset volume.
To silence the handset ringer:
Press OFF or MUTE on the handset. The handset
displays and Ringer muted briefly.
Quiet mode
You can turn on the quiet mode for a period of
time. During this period, all tones (except paging
tone) and call screening are muted.
1. Press and hold on the handset when it
is not in use.
2. Use the dialing keys (0-9) to enter the duration,
and then press SELECT to save.
To turn off the quiet mode, press and hold
on the handset when it is not in use.
About the built-in answering
system and voicemail service
For message recording, your telephone has a
built-in answering system, and it also supports
voicemail service offered by your telephone
service provider (subscription is required, and fee
may apply).
The main differences between them are:
Category Built-in
answering
system
Voicemail from
telephone
service
Storage Messages are
stored in the
telephone base.
Messages are
stored in a
server or system
provided by
your telephone
service
provider.
Your messages
will not be
deleted
automatically.
You have to
delete your
messages
manually.
Your messages
may be
automatically
deleted after a
period of time.
Contact your
telephone
service
provider for
more details.
Display
new
message
When you
received new
messages,
the handset
displays XX new
messages, and
the message
window on the
telephone base
flashes.
When you
received new
messages,
the handset
displays and
New voicemail.
Method
to retrieve
messages
To retrieve
messages:
Press on
the telephone
base; or
Press MENU on
the handset,
and then select
Play messages;
or
Access
remotely with
an access code.
To retrieve
messages, you
need an access
number and/
or a passcode
provided by
your telephone
service
provider.
New message indication
When there are new messages in the built-in
answering system, the handset displays XX new
messages, and the message window on the
telephone base flashes.
Message
window
display
Description
0No messages.
0 (flashing) After a power failutre, the number
in the message window flashes to
indicate that the date and time
need to be set.
1-99 Total number of old messages
and memos recorded.
The current message number
during old message playback.
0-99
(flashing)
Total number of new
messages and memos. The
number flashes when there
are new messages that have
not been reviewed.
Current message number
during new message
playback.
After a power failure, the
number in the message
window flashes.
Indicate that the date and time
need to be set.
1-99 & F
(alternating)
Memory is full. Messages must be
deleted before new messages
can be recorded.
1- 8The telephone base speaker
volume level while adjusting.
0- 6The telephone base ringer level
while adjusting.
Message
window
display
Description
-- The answering system is being
programmed by a system
handset.
The answering system is
answering a call or recording a
memo or announcement.
The answering system is being
accessed remotely.
The directory or caller ID log
is being accessed by a system
handset.
Turn on/ off the answering
system
The answering system must be turned on to
answer and record messages.
When the answering system is turned on, the
ANS ON/OFF light on the telephone base turns
on and ANS ON displays on the handset.
Press ANS ON/OFF on the base to turn the
answering system on or off. - OR -
1. Press MENU when the handset is not in use.
2. Press q or p to choose Answering sys and
then press SELECT.
3. Press q or p to choose Answer on/off and
then press SELECT.
4. Press q or p to choose Answer:On or
Answer:Off, then press SELECT to save.
Answering system settings
Set your built-in answering system
The answering system can record and store
up to 99 messages. Each message can be
up to 3 minutes in length. The total storage
capacity for the announcement, messages and
memos is approximately 14 minutes. The actual
recording time depends on individual message
characteristics. Messages remain available for
replay until you delete them.
If the answering system has less than 3 minutes of
recording time left, “Less than 3 minutes to record
is announced before the message playback and
Rec mem low appears on the handset screen.
If the memory is full, the answering system
announces, “Memory is full.” The number of
messages and F flash, alternatively, in the message
window, and Rec mem full appears on the handset
screen. You must delete some messages before
recording new ones.
Your answering system allows you to set your
announcement, to save and delete messages,
activate call screening, to set number of rings
before pick up, and to access remotely.
Voice language
NOTE: This feature is available in Canada
version only.
The voice prompt language is preset to English.
You can select English or French to be used for the
voice prompts in your answering system.
1. Press MENU when the handset is not in use.
2. Press q or p to choose Answering sys and
then press SELECT.
3. Press q or p to choose Ans sys setup and then
press SELECT.
4. Press q or p to choose Voice language and
then press SELECT.
5. Press q or p to choose English or Français and
then press SELECT.
Announcement
Your outgoing announcement plays when calls are
answered by the answering system. The telephone
has a default outgoing announcement, “Hello,
please leave a message after the tone.” You can
use this announcement, or record your own.
Record a new outgoing announcement:
The announcement can be up to 90 seconds in
length.
1. Press MENU when the handset is not in use.
2. Press q or p to choose Answering sys and
then press SELECT.
3. Press SELECT to choose Announcement.
4. The screen displays Play [2] Del [3] Rec [7] and
it announces,To play, press 2. To record, press
7.” Press 7 to record.
5. The handset announces,Record after the tone.
Press 5 when you are done.” and it displays
Recording... Stop [5].
6. After the tone, speak towards the handset
microphone.
7. Press 5 when finished. The handset plays back
the recorded announcement. Press 5 or OFF to
stop the playback at any time.
To listen to the recorded announcement again,
wait after playback has completed, then press
2.
NOTE: Announcements shorter than two
seconds will not be recorded.
Play your announcement:
1. Press MENU when the handset is not in use.
2. Press q or p to choose Answering sys and
then press SELECT.
3. Press SELECT to choose Announcement.
4. The screen displays Play [2] Del [3] Rec [7] and
it announces,To play, press 2. To record, press
7.” Press 2 to play the current announcement.
Options during playback:
1. Press VOL q or VOL p to adjust the listening
volume.
2. Press 5 or OFF to stop at any time.
Delete your announcement:
1. Press MENU when the handset is not in use.
2. Press q or p to choose Answering sys and
then press SELECT.
3. Press SELECT to choose Announcement.
4. The screen displays Play [2] Del [3] Rec [7] and
it announces,To play, press 2. To record, press
7.” Press 3 or DELETE to delete your recorded
announcement. The handset displays Annc
deleted and announces “Announcement
deleted.
NOTE: After you deleted your own recorded
announcement, the answering system
answers calls with the default announcement.
Set number of rings
You can set the answering system to answer an
incoming call after two, three, four, five or six
rings; or toll saver.
If you choose toll saver, the answering system
answers a call after two rings when you have new
messages, or after four rings when you have no
new messages. This enables you to check for new
messages and avoid paying unnecessary long
distance charges if you are calling from outside
your local area.
1. Press MENU when the handset is not in use.
2. Press q or p to choose Answering sys and
then press SELECT.
3. Press q or p to choose Ans sys setup and then
press SELECT.
4. Press q or p to choose # of rings and then
press SELECT.
5. Press q or p to choose from 6, 5, 4, 3, 2, or Toll
saver, then press SELECT to save.
Turn on or off the message alert tone
When the message alert tone is set to On, and
there is at least one new message, the telephone
base beeps every 10 seconds. The tone stops
when all new messages have been reviewed.
1. Press MENU when the handset is not in use.
2. Press q or p to choose Answering sys and
then press SELECT.
3. Press q or p to choose Ans sys setup and then
press SELECT.
4. Press q or p to choose Msg alert tone and
then press SELECT.
5. Press q or p to choose Tone:On or Tone:Off,
then press SELECT to save.
NOTE: The message alert tone beeps only if
all the following conditions are met.
- Anwering system is on.
- Messsage alert tone setting is on.
- There are new messages.
Playback messages
You can listen to messages at the telephone base
or on a cordless handset. When playback begins,
the total number of messages is annouced. Before
each message, you hear the day and time of the
recording. After the last message, you hear, “End
of messages.” Make sure you set the date and
time correctly. Refer to Set date and time for more
details.
To listen to messages at the base:
Press /PLAY when the phone is not in use.
When you have no message in the answering
system, the telephone base announces, “You
have no message.
Options during playback
Press pVOL + or qVOL - to adjust the listening
volume.
Press /SKIP to skip to the next message.
Press /REPEAT to repeat the playing
message. Press /REPEAT twice to listen to the
previous message.
Press X/DELETE to delete the playing message.
The telephone base advances to the next
message.
Press /STOP to stop the playback.
To listen to messages with the handset:
1. Press MENU when the handset is not in use. The
handset displays Play messages.
2. Press SELECT. If you have either new or old
messages, the messages play automatically.
The system announces the number of
messages, and then begins playback. The
message sequence is shown on the handset’s
screen.
3. Press OFF to stop the playback.
Options during playback
Press q/VOLUME or p/VOLUME to adjust the
listening volume.
Press 6 to skip to the next message.
Press 4 to repeat the playing message. Press 4
twice to listen to the previous message.
Press 3 or MUTE/DELETE to delete the playing
message. The telephone base advances to the
next message.
Press OFF to stop the playback.
Delete all messages
Using the base
1. Press X/DELETE when the telephone is not in
use. The telephone announces - To delete all old
messages, press DELETE again.
2. Press X/DELETE again. All previously reviewed
messages are erased and the telephone
announces - All old messages deleted.
Using the handset
1. Press MENU when the handset is not in use.
2. Press q or p to choose Answering sys and
then press SELECT.
3. Press q or p to choose Delete all old and then
press SELECT.
4. Press SELECT to confirm. The handset displays
Deleting... and then No old messages. It
returns to the previous menu, and you hear a
confirmtion tone.
Answering system remote access
You can reach your answering system remotely by
dialing your home telephone number from any
touch-tone telephone.
1. Dial your telephone number from any touch-
tone telephone.
2. Once the system plays your announcement,
enter the two-digit remote access code (19 is
the default code).
The system automatically announces the
number of new or old messages (if any), and
then begins to play them.
You can also enter the following remote commands.
Command Description
1Play all messages.
2Play only new messages.
3Delete the current message (during
playback).
33 Delete all old messages.
4Repeat the current message (during
playback).
5Stop.
*5 Hear a list of remote commands.
6Skip to the next message (during
playback).
*7 Record a new announcement.
8 End the call.
0 Turn the answering system on or off.
3. Hang up or press 8 to end the call.
NOTES:
If you do not press any key after you
enter the remote access code, all new
messages play. If there are no new
messages, all old messages play.
Once the new messages have played,
the telephone announces the help
menu options. If you do not press any
key within 20 seconds, the remote
access call automatically disconnects.
When the answering system is turned
off, the telephone answers after 10
rings, and announces, “Please enter
your remote access code.
When the memory is full, the answering
system answers incoming calls after 10
rings and announces, “Memory is full.
Enter your remote access code.
Change remote access code
1. Press MENU when the handset is not in use.
2. Press q or p to choose Answering sys and
then press SELECT.
3. Press q or p to choose Ans sys setup and then
press SELECT.
4. Press q or p to choose Remote code and then
press SELECT.
5. Use the dialing keys to enter a two-digit
number.
-OR-
Press q or p to scroll to a desired two-digit
number.
6. Press SELECT to confirm.
Call intercept while using answering system
When a caller is leaving a message on your
answering system, you can stop recording and talk
to the caller by pressing or on the handset.
Recording memo
Memos are your own recorded messages used
as reminders for yourself or others using the
same answering system. You can record your
own memos using a system handset. Playback
and delete them in the same way as incoming
messages.
1. Press MENU when the handset is not in use.
2. Press q or p to choose Answering sys and
then press SELECT.
3. Press q or p to choose Record memo and
then press SELECT. The handset displays
Recording... Stop [5] and announces, “Record
after the tone. Press 5 when you are done.
4. Speak towards the handset microphone. Press 5
or OFF when you finish recording. The handset
announces “Recorded.
NOTES:
If you record a memo when the
answering system memory is full, the
system announces, “Memory is full.
Each memo can be up to three minutes
in length. Memos shorter than two
second are not recorded.
When the answering system has less
than three minutes of recording time
left, the handset announces, “Less than
three minutes to record,” and displays
Rec mem low.
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures corporelles
ou d’électrocution, suivez toujours ces mesures préventives de
base lorsque vous utilisez votre téléphone :
1. Lisez et comprenez bien toutes les instructions.
2. Observez toutes les instructions et mises en garde inscrites
sur l’appareil.
3. Débranchez ce téléphone de la prise murale avant de le
nettoyer. N’utilisez pas de nettoyeurs liquides ni en aérosol.
N’utilisez qu’un chiffon doux et légèrement humecté.
4. ATTENTION: Ne pas installer le socle téléphonique à une
hauteur supérieure à 2 mètres.
5. N’utilisez pas ce produit près de l’eau, tel que près d’un
bain, d’un lavabo, d’un évier de cuisine, d’un bac de lavage
ou d’une piscine, ou dans un sous-sol humide ou sous la
douche.
6. Ne déposez pas ce téléphone sur un chariot, support
ou table chancelants. L’appareil pourrait tomber et être
sérieusement endommagé.
7. Évitez d’installer le système téléphonique dans les endroits
soumis à une température extrême, à la lumière directe du
soleil ou à proximité immédiate d’autres appareils électriques
ou électroniques. Protégez votre téléphone contre les
sources d’humidité, la poussière, les vapeurs et les liquides
corrosifs.
8. Le boîtier de l’appareil est doté de fentes et d’ouvertures
d’aération situées à l’arrière ou en dessous. Afin d’emcher
la surchauffe, ces ouvertures ne doivent pas être obstres
en plaçant l’appareil sur un lit, divan, tapis ou autre surface
similaires. Ne placez pas cet appareil à proximité d’un
élément de chauffage ni d’une plinthe électrique. De plus,
ne l’installez pas dans une unité murale ou un cabinet fermé
qui ne possède pas d’aération aquate.
9. Ne faites fonctionner cet appareil qu’avec le type
d’alimentation indiqué sur les étiquettes de l’appareil. Si
vous ne connaissez pas le voltage de votre maison, consultez
votre marchand ou votre fournisseur d’électricité.
10. Ne déposez rien sur le cordon d’alimentation. Installez cet
appareil dans un endroit sécuritaire, là où personne ne
pourra trébucher sur la ligne d’alimentation ni le cordon
téléphonique modulaire.
11. N’insérez jamais d’objets à travers les fentes et ouvertures
de cet appareil, car ils pourraient toucher à des points
de tension dangereux ou court-circuiter des pièces, ce
qui constituerait un risque d’incendie ou d’électrocution.
N’échappez pas de liquides dans l’appareil.
12. Afin de réduire les risques d’électrocution, ne démontez
pas l’appareil, mais apportez-le plutôt à un centre de service
qualifié s’il doit être réparé. En enlevant le couvercle,
vous vous exposez à des tensions dangereuses ou autres
dangers similaires. Un remontage inadéquat peut être à
l’origine d’une électrocution lors d’une utilisation ultérieure
de l’appareil. Débranchez l’appareil avant de procéder au
nettoyage. Utilisez un chiffon humide et doux.
13. Ne surchargez pas les prises de courant et les rallonges.
14. Débranchez cet appareil de la prise de courant et
communiquez avec le département de service à la clientèle
de VTech dans les cas suivants :
Lorsque le cordon d’alimentation est endommagé ou
écorché.
Si du liquide a été échappé dans l’appareil.
Si l’appareil a été exposé à une source d’humidité telle
que la pluie ou l’eau.
Si le produit ne fonctionne pas normalement en
respectant les instructions de fonctionnement. Réglez
uniquement les commandes indiquées dans le les
instructions de fonctionnement. Les réglages incorrects
des autres commandes pourraient provoquer un
dommage qui pourrait exiger un travail exhaustif
de la part d’un technicien autorisé afin de rétablir le
fonctionnement normal de l’appareil.
Si le produit a été échappé et que le socle et/ou le
combiné a été endommagé.
Si le produit affiche une nette diminution de sa
performance.
15. Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant
un orage. Les éclairs peuvent être à l’origine d’une
électrocution.
16. N’utilisez pas le téléphone pour rapporter une fuite de
gaz à proximité de la fuite. En certaines circonstances, une
flammèche pourrait être provoquée lorsque l’adaptateur
est branché à une prise de courant, ou lorsque le combiné
est déposé sur le socle. Ceci est un événement commun
associé à la fermeture d’un circuit électrique. L’utilisateur
ne devrait pas brancher le téléphone à une prise de
courant, et ne devrait pas déposer le combiné chargé sur
le socle, si le téphone se trouve à proximité d’un endroit
comportant des concentrations de gaz inflammables, à
moins que la ventilation soit aquate. Une flammèche
dans un tel endroit pourrait provoquer un incendie ou une
explosion. De tels environnements peuvent comprendre:
des endroits où l’on utilise de l’oxygène médical sans
ventilation adéquate; des gaz industriels (dissolvants de
nettoyage, des vapeurs d’essence, etc.); une fuite de gaz
naturel, etc.
17. Ne placez que le combiné de votre téléphone près de votre
oreille lorsqu’en mode de conversation.
18. Ces adaptateurs ont été conçus pour être orientés en
position verticale ou montés au sol. Les broches ne sont
pas conçues pour maintenir l’adaptateur en place si celui-ci
est barnché dans une prise au plafond ou sous une table/
armoire.
19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le
socle de prise de courant doit etre installe a proximite du
materiel et doit etre aisement accessible.
20. MISE EN GARDE: Il peut y avoir un risque
d’explosion si vous utilisez le mauvais type de piles pour le
téléphone. N’utilisez que les piles rechargeable inclus ou les
piles de rechange. N’incinérez pas les piles. Celles-ci
risqueraient d’exploser. Mettre au rebut les batteries
usagées conformément aux instructions du fabricant.
Débrancher les lignes téléphoniques avant le
remplacement des piles.
Évite d’utiliser la batterie dans les conditions suivantes:
des températures extrêmes faibles ou élevées
auxquelles une batterie peut être soumise pendant
l’utilisation, le stockage ou le transport.
remplacement d’une batterie par un type incorrect
pouvant supprimer une protection.
mise au rebut d’une batterie dans un feu ou dans un
four chaud, ou écrasement mécanique ou coupure
d’une batterie, susceptible de provoquer une
explosion.
maintien d’une batterie dans un environnement
à très haute temrature pouvant provoquer
une explosion ou la fuite de liquide ou de gaz
inflammables.
batterie soumise à une pression de l’air
extrêmement faible pouvant provoquer une
explosion ou la fuite de liquide ou de gaz
inflammables.
21. N’utilisez que les adaptateurs inclus avec ce produit.
L’utilisation d’un adaptateur dont la polarité ou la tension
serait inadéquate risque d’endommager sérieusement le
produit et mettre votre sécurité en péril.
22. La plaque signalétique appliquée est située au bas ou à
proximité du produit.
CONSERVEZ CES INSTRUCTIONS
Pile
N’utilisez que la pile incluse ou l’équivalent.
Ne jetez pas la pile au feu. Vérifiez les instructions
spécifiques de mise aux rebus auprès des autorités locales.
N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en
échapperait est corrosif et pourrait causer des brûlures ou
des blessures aux yeux ou à la peau. L’électrolyte est toxique
si avalé.
Soyez prudents lorsque vous manipulez les piles afin
d’éviter les courts-circuits provoqués par des matériaux
conducteurs.
Rechargez la pile incluse avec cet appareil, selon les
instructions et limites spécifiées dans ce guide d’utilisation.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (s’applique uniquement aux
téléphones numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une
firme de recherche inpendante, a mené une évaluation
pluridisciplinaire des interférences entre les téléphones sans
fil portatifs et les stimulateurs cardiaques implantés dans
l’organisme. Appuyée par l’Administration des aliments et
drogues (FDA) des États-Unis, la firme WTR recommande aux
médecins :
Avis aux détenteurs de stimulateurs cardiaques
Ils doivent tenir le téphone sans fil à une distance d’au
moins six pouces du stimulateur cardiaque.
Ils ne doivent PAS placer le téphone sans fil directement
sur le stimulateur cardiaque, tel que dans une poche de
chemise, lorsque celui-ci est en marche.
Ils doivent utiliser le téléphone sans fil en l’appuyant
sur l’oreille qui se trouve dans la direction opposée au
stimulateur cardiaque.
L’étude effecte par l’organisme WRS n’a pas identifié de
risque pour les détenteurs de simulateurs cardiaques causés
par les gens qui utilisent un téphone sans fil à proximité de
ceux-ci.
À propos des téléphones sans fil
Confidentialité : Les mêmes caractéristiques qui constituent
des avantages pour les téléphones sans fil affichent également
des restrictions. Les appels téléphoniques sont transmis entre
le combiné sans fil et le socle par le biais d’ondes radio ; il y a
donc la possibilité que vos conversations téléphoniques sans fil
soient interceptées par des équipements de réception radio se
trouvant dans la pore du combiné sans fil. Pour cette raison,
vous ne devez pas percevoir les communications téléphoniques
sans fil comme étant aussi confidentielles que celles des
téléphones à cordons.
Alimentation électrique : Le socle de ce téléphone sans fil
doit être branché à une prise électrique fonctionnelle. La prise
électrique ne doit pas être contrôlée par un interrupteur mural.
Les appels ne pourront pas être effects du combiné sans fil
si le socle est débranché ou mis hors tension ou si le courant est
coupé.
Possibilité d’interférences aux téléviseurs : Certains téléphones
sans fil fonctionnent sur des fréquences pouvant causer
des interrences aux téléviseurs et aux magnétoscopes.
Pour réduire ou prévenir de telles interrences, ne placez
pas le socle du téléphone sans fil près ou sur un téléviseur
ou magnétoscope. S’il y a présence de parasites, il est
conseillé d’éloigner le téléphone sans fil du téléviseur ou du
magnétoscope afin de réduire possiblement les interférences.
Piles rechargeables : Manipulez les piles avec soin afin de ne
pas les court-circuiter avec des bagues, bracelets ou clés. Les
piles ou le conducteur peut surchauffer et causer des blessures.
Respectez la polarité adéquate entre la pile et le chargeur.
Les bloc-piles rechargeables à l’hydrure métallique de nickel :
Jetez ces blocs-piles de manière écologique et sécuritaire. Ne
les incirez pas et ne les percez pas. Tel que les autres piles de
ce type, elles pourraient dégager une matière toxique qui peut
causer
des blessures corporelles si elles sont brûlées ou percées.
The RBRC SEAL
The RBRC seal on the nickel-metal hydride
battery indicates that VTech Communications,
Inc. is voluntarily participating in an industry
program to collect and recycle these batteries at
the end of their useful lives, when taken out of
service within the United States and Canada.
The program provides a convenient alternative
to placing used nickel-metal hydride batteries into the trash or
municipal waste, which may be illegal in your area.
VTech’s participation makes it easy for you to drop off the spent
battery at local retailers participating in the RBRC program or at
authorized VTech product service centers. Please call
1 (800) 8 BATTERY® for information on Ni-MH battery recycling
and disposal bans/restrictions in your area. VTech’s involvement
in this program is part of its commitment to protecting our
environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks
of Call2recycle, Inc.
FCC, ACTA and IC regulations
FCC Part 15
NOTE: This equipment has been tested and found to comply
with the requirements for a Class B digital device under Part 15
of the Federal Communications Commission (FCC) rules. These
requirements are intended to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
WARNING: Changes or modifications to this equipment not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation. Privacy of communications may not be
ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the
amount of radio frequency energy that can be safely absorbed
by a user or bystander according to the intended usage of the
product. This product has been tested and found to comply
with the FCC criteria. The handset may be safely held against
the ear of the user. The telephone base shall be installed and
used such that parts of the user’s body other than the hands are
maintained at a distance of approximately 20 cm (8 inches) or
more.
This Class B digital apparatus complies with Canadian
requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and
with technical requirements adopted by the Administrative
Council for Terminal Attachments (ACTA). The label on the back
or bottom of this equipment contains, among other things,
a product identifier in the format US:AAAEQ##TXXXX. This
identifier must be provided to your telephone service provider
upon request.
The plug and jack used to connect this equipment to premises
wiring and the telephone network must comply with applicable
Part 68 rules and technical requirements adopted by ACTA. A
compliant telephone cord and modular plug is provided with
this product. It is designed to be connected to a compatible
modular jack that is also compliant. An RJ11 jack should normally
be used for connecting to a single line and an RJ14 jack for two
lines. See the installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine
how many devices you may connect to your telephone line
and still have them ring when you are called. The REN for this
product is encoded as the 6th and 7th characters following the
US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In
most, but not all areas, the sum of all RENs should be five (5.0)
or less. For more information, please contact your telephone
service provider.
This equipment must not be used with Party Lines. If you have
specially wired alarm dialing equipment connected to your
telephone line, ensure the connection of this equipment does
not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone
service provider or a qualified installer.
If this equipment is malfunctioning, it must be unplugged
from the modular jack until the problem has been corrected.
Replacement to this telephone equipment can only be made
by the manufacturer or its authorized agents. For replacement
procedures, follow the instructions outlined under the Limited
warranty.
If this equipment is causing harm to the telephone network,
the telephone service provider may temporarily discontinue
your telephone service. The telephone service provider is
required to notify you before interrupting service. If advance
notice is not practical, you will be notified as soon as possible.
You will be given the opportunity to correct the problem and
the telephone service provider is required to inform you of
your right to file a complaint with the FCC. Your telephone
service provider may make changes in its facilities, equipment,
operation, or procedures that could affect the proper
functioning of this product. The telephone service provider is
required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it
is hearing aid compatible.
If this product has memory dialing locations, you may choose to
store emergency telephone numbers (e.g., police, fire, medical)
in these locations. If you do store or test emergency numbers,
please:
Remain on the line and briefly explain the reason for the call
before hanging up.
Perform such activities in off-peak hours, such as early morning
or late evening.
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including
interference that may cause undesired operation of the device.
Privacy of communications may not be ensured when using this
telephone.
The term ‘’IC:‘’ before the certification/registration number only
signifies that the Industry Canada technical specifications were
met.
The Ringer Equivalence Number (REN) for this terminal
equipment is 1.0. The REN indicates the maximum number of
devices allowed to be connected to a telephone interface. The
termination of an interface may consist of any combination of
devices subject only to the requirement that the sum of the
RENs of all the devices not exceed five.
This product meets the applicable Innovation, Science and
Economic Development Canada technical specifications.
California energy commission
battery charging testing
instructions
This telephone is set up to comply with the energy-conserving
standards right out of the box. These instructions are intended for
California Energy Commission (CEC) compliance testing only. When
the CEC battery charging testing mode is activated, all telephone
functions, except battery charging, will be disabled.
To activate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power
outlet. Make sure all handsets are plugged with charged
batteries before proceeding.
2. While you press and hold FIND HANDSET, plug the
telephone base power adapter back to the power outlet.
3. After about 20 seconds, when the IN USE light starts flashing,
release FIND HANDSET and then press it again within 2
seconds.
When the phone successfully enters the CEC battery charging
testing mode, the IN USE light turns off and all handsets
display 1.PRESS FIND HS ON BASE 4 SEC and 2.THEN PRESS #
ON HANDSET alternately.
When the phone fails to enter this mode, repeat Step 1 through
Step 3 above.
To deactivate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power
outlet, and then plug it back in. Then the telephone base is
powered up as normal.
2. Place the handset in the telephone base to register it back. It
displays Registering...
The handset show Registered and you hear a beep when the
registration process completes. The registration process takes
about 90 seconds to complete.
Limited Warranty
What does this limited warranty cover?
The manufacturer of this VTech product, VTech Communications,
Inc. (“VTech”), warrants to the holder of a valid proof of purchase
(“Consumer” or “you”) that the Product and all accessories
provided by VTech in sales package (“Product”) are free from
material defects in material and workmanship, pursuant to
the following terms and conditions, when installed and used
normally and in accordance with operating instructions. This
limited warranty extends only to the Consumer for Products
purchased and used in the United States of America and Canada.
What will VTech Communications do if the Product is not free
from material defects in materials and workmanship during the
limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service
representative will replace at VTech’s option, without charge,
a Materially Defective Product. If we choose to replace the
Product, we may replace it with a new or refurbished Product
of the same or similar design. VTech will return replacement
products to you in working condition. VTech will retain defective
parts, modules, or equipment. Replacement of the Product, at
VTech’s option, is your exclusive remedy. You should expect the
replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the product extends for ONE (1)
YEAR from date of purchase (90 days on products purchased as
Refurbished*). This limited warranty also applies to replacement
Products for a period of either (a) 90 days from the date the
replacement Product is shipped to you or (b) the time remaining
on the original one-year limited warranty (90-day limited
warranty on products that are purchased as Refurbished*),
whichever is longer.
*Refurbished products purchased from our online store carry a
90-day replacement warranty.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident,
shipping or other physical damage, improper installation,
abnormal operation or handling, neglect, inundation, fire,
water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or
modification by anyone other than an authorized service
representative of VTech; or
3. Product to the extent that the problem experienced is
caused by signal conditions, network reliability or cable or
antenna systems; or
4. Product to the extent that the problem is caused by use
with non-VTech electrical accessories; or
5. Product whose warranty/quality stickers, Product serial
number plates or electronic serial numbers have been
removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair
from outside the United States, or used for commercial
or institutional purposes (including but not limited to
Products used for rental purposes); or
7. Product returned without valid proof of purchase (see 2
below); or
8. Charges for installation or set up, adjustment of customer
controls, and installation or repair of systems outside the
unit.
How do you get warranty service?
To obtain warranty service in the United States of America, please
visit our website at www.vtechphones.com or call
1 (800) 595-9511 for instructions regarding where to return the
Product. In Canada, go to phones.vtechcanada.com or dial
1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual
- a check of the Product’s controls and features may save you a
service call.
Except as provided by applicable law, you assume the risk of loss
or damage during transit and transportation and are responsible
for delivery or handling charges incurred in the transport of
Product(s) to the service location. VTech will return replaced
product under this limited warranty to you, transportation,
delivery or handling charges prepaid. VTech assumes no risk for
damage or loss of the Product in transit.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including
the Product to the VTech service location along with a
description of the malfunction or difficulty;
2. Include “valid proof of purchase” (sales receipt) identifying
the Product purchased (Product model) and the date of
purchase or receipt; and
3. Provide your name, complete and correct mailing address,
and telephone number.
Other limitations
This warranty is the complete and exclusive agreement
between you and VTech. It supersedes all other written or oral
communications related to this product. VTech provides no other
warranties for this product. The warranty exclusively describes all
of VTech’s responsibilities regarding the product.
There are no other expressed warranties. No one is authorized to
make modifications to this warranty and you should not rely on
any such modification.
State Law Rights: This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
Limitations: Implied warranties, including those of fitness for a
particular purpose and merchantability (an unwritten warranty
that the product is fit for ordinary use) are limited to one year
from date of purchase. Some states do not allow limitations on
how long an implied warranty lasts, so the above limitation may
not apply to you.
In no event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages (including, but not
limited to lost profits or revenue, inability to use the product, or
other associated equipment, the cost of substitute equipment,
and claims by third parties) resulting from the use of this product.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion
may not apply to you.
Please retain your original sales receipt as proof of purchase
Disclaimer and Limitation of
Liability
VTech Communications, Inc. and its suppliers assume no
responsibility for any damage or loss resulting from the use of
this user’s manual. VTech Communications, Inc. and its suppliers
assume no responsibility for any loss or claims by third parties
that may arise through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR
97223, United States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada
Technical specifications
Frequency
control
Crystal controlled PLL synthesizer
Transmit
frequency
Handset: 1921.536-1928.448 MHz
Telephone Base: 1921.536-1928.448 MHz
Channels DECT channel: 5
Nominal
effective
range
Maximum power allowed by FCC and
IC. Actual operating range may vary
according to environmental conditions
at the time of use.
Power
requirement
Handset: 2.4V Ni-MH battery
Telephone base: 6V DC @ 0.4A
Charger: 6V DC @ 0.4A
Memory Directory: 50 memory locations;
up to 30 digits and 15 characters
Caller ID log: 50 memory locations;
up to 24 digits and 15 characters
Telephones identified with this logo have
reduced noise and interference when
used with most T-coil equipped hearing
aids and cochlear implants. The TIA-1083
Compliant Logo is a trademark of the
Telecommunications Industry Association.
Used under license.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
Turn on or off the call screening
Use this feature to choose whether incoming
messages can be heard over the telephone base
when they are being recorded. If you turn call
screening on, you hear the incoming message.
1. Press MENU when the handset is not in use.
2. Press q or p to choose Answering sys and then
press SELECT.
3. Press q or p to choose Ans sys setup and then
press SELECT.
4. Press SELECT again to choose Call screening.
5. Press q or p to choose Screening:On or
Screening:Off, then press SELECT to save.
Screen a call with answering system
Screen calls at the cordless handset:
If the answering system is on and a call is being
answered by the answering system, the handset
shows To screen call, press [SELECT].
Press SELECT to screen the call on your handset.
The handset shows Screening....
Option while a message is being recorded
Press q/VOLUME or p/VOLUME on the
handset to adjust the call screening volume.
Screen calls at the base:
If the answering system and call screening are on,
the announcement and the incoming message
broadcast at the telephone base when a call is
answered by the answering system.
Option while a message is being recorded
Press qVOL - or pVOL + on the telephone base
to adjust the call screening volume.
Press /PLAY to temporarily turn on the
screening if the call screening is set to off.
Retrieve voicemail from
telephone service
Voicemail is a feature available from most
telephone service providers. It may be included
with your telephone service, or may be optional.
Fees may apply.
Retrieve voicemail
When you received a voicemail, the handset
displays and New voicemail. To retrieve, you
typically dial an access number provided by your
telephone service provider, and then enter a security
code. Contact your telephone service provider
for instructions on how to configure the voicemail
settings and listen to messages.
NOTE: After you have listened to all new
voicemail messages, the indicators on the
handset turn off automatically.
Set your voicemail number
You can save your access number on each handset
for easy access to your voicemail.
After you saved the voicemail number, you can
press and hold to retrieve voicemail.
1. Press MENU when the phone is not in use.
2. Scroll to Settings and then press SELECT.
3. Scroll to Voicemail # and then press SELECT.
4. Use the dialing keys to enter the voicemail
number (up to 30 digits).
5. Press SELECT to save.
Clear the new voicemail indicators
If you have retrieved your voicemail while away from
home, and the handset still displays the new voicemail
indicators, use this feature to turn off the indicators.
NOTE: This feature turns off the indicators
only, it does not delete your voicemail
messages.
1. Press MENU when the phone is not in use.
2. Scroll to Settings and then press SELECT.
3. Scroll to Clr voicemail and then press SELECT.
4. Press SELECT again to confirm. You hear a
confirmation tone.
ECO mode
This power conserving technology reduces power
consumption for optimal battery performance. The
ECO mode activates automatically whenever the
handset is synchronized with the telephone base.
General product care
Taking care of your telephone
Your cordless telephone contains sophisticated
electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original
packing materials to protect your telephone if you
ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do
not use the handset outdoors in the rain, or handle
it with wet hands. Do not install the telephone base
near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment. For your
own safety, take caution when using electrical
appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that
should retain its luster for many years. Clean it
only with a dry non-abrasive cloth. Do not use
dampened cloth or cleaning solvents of any kind.
Need help?
For operations and guides to help you using your
telephone, and for the latest information and
supports, go and check the online help topics and
online FAQs.
Use your smartphone or mobile device to access our
online help.
• Go to https://help.vtechphones.com/cs6529 (US);
OR https://phones.vtechcanada.com/en/support/
general/manuals?model=cs6529 (Canada)
• Scan the QR code on the right.
Launch the camera app or QR code
scanner app on your smartphone or
tablet. Hold the device’s camera up
to the QR code and frame it. Tap the
notification to trigger the redirection
of the online help.
- If the QR code is not clearly
displayed, adjust your camera’s focus
by moving your device closer or
further away until it is clear.
You can also call our Customer
Support at 1 (800) 595-9511 [in US] or
1 (800) 267-7377 [in Canada] for help.
Recycle this product
when you are done
with it
Scan the QR code on the right or visit
www.vtechphones.com/recycle.
(For the US only)
CS6529 (US)
CS6529 (CA)
  • Page 1 1
  • Page 2 2

VTech CS6529 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues