VTech DS6611-3 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur
BC
DS6611
DS6611-2
DS6611-3
DECT 6.0 cordless telephone
with BLUETOOTH® wireless technology
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
latest VTech product news.
User’s manual
Congratulations
on purchasing your new VTech product.
Before using this telephone, please read
Important safety instructions.
This manual has all the feature
operations and troubleshooting
necessary to install and operate your
new VTech telephone. Please review
this manual thoroughly to ensure
proper installation and operation of
this innovative and feature rich VTech
product.
For support, shopping, and everything
new at VTech, visit our website at
www.vtechphones.com.
In Canada, please visit
www.vtechcanada.com.
The ENERGY STAR® program
(www.energystar.gov)
recognizes and encourages
the use of products that
save energy and help
protect our environment.
We are proud to mark this
product with the ENERGY
STAR® label indicating it
meets the latest energy
efficiency guidelines.
Telephones identified with
this logo have reduced
noise and interference
when used with most T-coil
equipped hearing aids
and cochlear implants.
The TIA-1083 Compliant
Logo is a trademark of
the Telecommunications
Industry Association. Used
under license.
Important safety
instructions
When using your telephone equipment,
basic safety precautions should always
be followed to reduce the risk of fire,
electric shock and injury, including the
following:
Read and understand all instructions.
Follow all warnings and instructions
marked on the product.
Unplug this product from the wall
outlet before cleaning. Do not use
liquid or aerosol cleaners. Use a
damp cloth for cleaning.
Do not use this product near water
such as near a bath tub, wash bowl,
kitchen sink, laundry tub or swimming
pool, or in a wet basement or shower.
Do not place this product on an
unstable table, shelf, stand or other
unstable surfaces.
Slots and openings in the back or
bottom of the telephone base and
handset are provided for ventilation.
To protect them from overheating,
these openings must not be blocked
by placing the product on a soft
surface such as a bed, sofa or
rug. This product should never be
placed near or over a radiator or heat
register. This product should not be
placed in any area where proper
ventilation is not provided.
This product should be operated
only from the type of power source
indicated on the marking label. If
you are not sure of the type of power
supply in your home or office, consult
your dealer or local power company.
Do not allow anything to rest on
the power cord. Do not install this
product where the cord may be
walked on.
1.
2.
3.
4.
5.
6.
7.
8.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
Never push objects of any kind into
this product through the slots in the
telephone base or handset because
they may touch dangerous voltage
points or create a short circuit. Never
spill liquid of any kind on the product.
To reduce the risk of electric shock,
do not disassemble this product,
but take it to an authorized service
facility. Opening or removing parts of
the telephone base or handset other
than specified access doors may
expose you to dangerous voltages or
other risks. Incorrect reassembling
can cause electric shock when the
product is subsequently used.
Do not overload wall outlets and
extension cords.
Unplug this product from the wall
outlet and refer servicing to an
authorized service facility under the
following conditions:
When the power supply cord or
plug is damaged or frayed.
If liquid has been spilled onto the
product.
If the product has been exposed
to rain or water.
If the product does not operate
normally by following the
operating instructions. Adjust only
those controls that are covered
by the operation instructions.
Improper adjustment of other
controls may result in damage and
often requires extensive work by
an authorized technician to restore
the product to normal operation.
If the product has been dropped
and the telephone base and/or
handset has been damaged.
If the product exhibits a distinct
change in performance.
9.
10.
11.
12.
Avoid using a telephone (other than
cordless) during an electrical storm.
There is a remote risk of electric
shock from lightning.
Do not use the telephone to report
a gas leak in the vicinity of the
leak. Under certain circumstances,
a spark may be created when the
adapter is plugged into the power
outlet, or when the handset is
replaced in its cradle. This is a
common event associated with the
closing of any electrical circuit. The
user should not plug the phone
into a power outlet, and should
not put a charged handset into
the cradle, if the phone is located
in an environment containing
concentrations of flammable or
flame-supporting gases, unless there
is adequate ventilation. A spark in
such an environment could create a
fire or explosion. Such environments
might include: medical use of
oxygen without adequate ventilation;
industrial gases (cleaning solvents;
gasoline vapors; etc.); a leak of
natural gas; etc.
Only put the handset of your
telephone next to your ear when it is
in normal talk mode.
The power adapters are intended to
be correctly oriented in a vertical or
floor mount position. The prongs are
not designed to hold the plug in place
if it is plugged into a ceiling,
under-the-table or cabinet outlet.
SAVE THESE INSTRUCTIONS
Battery
CAUTION: Use Only Supplied
Battery.
Do not dispose of the battery in a fire.
Check with local waste management
codes for special disposal instructions.
13.
14.
15.
16.
Do not open or mutilate the battery.
Released electrolyte is corrosive and
may cause burns or injury to the eyes
or skin. The electrolyte may be toxic if
swallowed.
Exercise care in handling batteries in
order not to create a short circuit with
conductive materials.
Charge the battery provided with this
product only in accordance with the
instructions and limitations specified
in this manual.
Precautions for users of
implanted cardiac pacemakers
Cardiac pacemakers (applies only to
digital cordless telephones):
Wireless Technology Research, LLC
(WTR), an independent research entity,
led a multidisciplinary evaluation of the
interference between portable wireless
telephones and implanted cardiac
pacemakers. Supported by the U.S.
Food and Drug Administration, WTR
recommends to physicians that:
Pacemaker patients
Should keep wireless telephones at
least six inches from the pacemaker.
Should NOT place wireless telephones
directly over the pacemaker, such as in
a breast pocket, when it is turned ON.
Should use the wireless telephone at
the ear opposite the pacemaker.
WTR’s evaluation did not identify any
risk to bystanders with pacemakers
from other persons using wireless
telephones.
About cordless telephones
Privacy: The same features that make
a cordless telephone convenient
create some limitations. Telephone
calls are transmitted between the
telephone base and the cordless
handset by radio waves, so there is a
possibility that the cordless telephone
conversations could be intercepted
by radio receiving equipment within
range of the cordless handset. For
this reason, you should not think of
cordless telephone conversations as
being as private as those on corded
telephones.
Electrical power: The telephone
base of this cordless telephone must
be connected to a working electrical
outlet. The electrical outlet should not
be controlled by a wall switch. Calls
cannot be made from the cordless
handset if the telephone base is
unplugged, switched off or if the
electrical power is interrupted.
Potential TV interference: Some
cordless telephones operate
at frequencies that may cause
interference to televisions and
VCRs. To minimize or prevent
such interference, do not place
the telephone base of the cordless
telephone near or on top of a TV or
VCR. If interference is experienced,
moving the cordless telephone farther
away from the TV or VCR often
reduces or eliminates the interference.
Rechargeable batteries: Exercise
care in handling batteries in order
not to create a short circuit with
conducting material such as rings,
bracelets and keys. The battery or
conductor may overheat and cause
harm. Observe proper polarity
between the battery and the battery
charger.
Nickel-metal hydride rechargeable
batteries: Dispose of these batteries
in a safe manner. Do not burn or
puncture the battery. Like other
batteries of this type, if burned or
punctured, they could release caustic
material which could cause injury.
Table of contents
What’s in the box.........................1
Overview ......................................2
Handset overview ...............................2
Telephone base overview ...................3
Charger overview ...............................4
Display icons overview .......................4
Handset and Telephone base
lights overview .................................4
Connect ........................................5
Connect the telephone base ...............5
Connect the charger ...........................5
Mount the telephone base ..................5
Install and charge the battery .............6
Charge the battery ..............................7
Before use ....................................8
Set date and time ...............................8
Check for a dial tone ...........................8
Operating range ..................................8
Bluetooth ......................................9
Glossary of terms ............................10
Bluetooth setup .................................11
VTech Connect to CellTM application ... 11
Add a Bluetooth enabled cell phone... 11
Add a Bluetooth enabled headset ....12
Auto connection ................................13
Connect a paired cell phone
or headset .....................................13
Disconnect a paired cell phone
or headset .....................................13
Review the cell devices list ...............13
Download phonebook .......................13
Configure your telephone ........15
Using the handset menu ...................15
Set language ....................................15
Set date and time .............................15
Home area code ...............................16
Dial mode .........................................16
Temporary tone dialing .....................16
Telephone Operations ..............17
Make a home call .............................17
Predial a home call ...........................17
Answer a home call ..........................17
End a home call ................................17
Make a cell call .................................18
Predial a cell call ...............................18
Answer a cell call ..............................18
End a cell call ...................................18
Answer a cell call while on
a home call ....................................18
Answer a home call while on
a cell call .......................................19
Speakerphone ..................................19
Volume ..............................................19
Mute ..................................................19
Join a call in progress (for multiple
handset models only) ....................19
Call waiting on the home line ............19
Call waiting on the cell line ...............20
Chain dialing .....................................20
Find handset .....................................20
Intercom ............................................21
Transfer a call ...................................21
Answer an incoming call during
an intercom call .............................22
Redial list ..................................22
Review a redial list entry ...................22
Dial a redial list entry ........................22
Delete a redial list entry ....................22
Phonebook .................................23
Add a phonebook entry ....................23
Review phonebook entries ...............24
Alphabetical search ..........................24
Delete a phonebook entry ................24
Delete all phonebook entries ............25
Edit a phonebook entry ....................25
Dial a phonebook entry ....................25
Caller ID ......................................25
Review the caller ID log ....................25
Memory match ..................................26
Missed call indicator .........................26
View dialing options ..........................26
Dial a caller ID log entry ...................27
Save a caller ID log entry to
the phonebook ..............................27
Delete the caller ID log entries .........27
Call block ...................................28
Block unknown calls .........................28
Add a call block list entry ..................28
Save a caller ID log entry to
call block list ..................................29
Review the call block list ...................29
Edit a call block list entry ..................29
Delete a call block list entry ..............29
Sound settings .........................30
Key tone ............................................30
Ringer tone .......................................30
Handset ringer volume .....................30
Temporary ringer silencing ...............30
Retrieve voicemail from
telephone service ...................31
Retrieve voicemail ............................31
Turn off the new
voicemail indicators .......................31
Cell phone voicemail ........................31
Expand your telephone system ...32
Add and register a handset ..............32
Deregister all devices .......................32
Screen messages ......................33
ECO mode ..................................34
General product care ................35
Frequently asked questions .....35
The RBRC® seal .........................38
FCC, ACTA and
IC regulations .........................39
California Energy Commission
battery charging
testing instructions ................41
For C-UL compliance only ........41
Limited Warranty .......................44
Technical Specifications ........... 46
1
What’s in the box
Your telephone package contains the
following items. Save your sales receipt
and original packaging in case it is
necessary to ship your telephone for
warranty service.
NOTE
To purchase replacement batteries or power
adapters, visit our website at
www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to
www.vtechcanada.com or dial
1 (800) 267-7377.
1 set for DS6611;
2 sets for DS6611-2;
3 sets for DS6611-3
Abridged user’s
manual
Quick start guide
1 set for DS6611-2;
2 sets for DS6611-3
1 set for DS6611/DS6611-2/DS6611-3
1 set for DS6611/DS6611-2/DS6611-3
Important Safety
Instructions
2
Overview
Handset overview
1 Handset earpiece
2 LCD display
3 MENU/SELECT
Show the menu.
While in a menu, press to select
an item, or save an entry or
setting.
4 OFF/CANCEL
Hang up a call.
Silence the ringer temporarily
while the handset is ringing.
Press and hold to erase the
missed call indicator while the
phone is not in use.
Press to return to the previous
menu; or press and hold to return
to idle mode, without making
changes.
5
Press repeatedly to show other
dialing options when reviewing a
caller ID log entry.
6 MUTE/DELETE
Mute the microphone during a
call.
Delete digits or characters while
using the dialing keys.
Silence the ringer temporarily
while the handset is ringing.
7 REDIAL/PAUSE
Press repeatedly to review the
redial list.
Press and hold to insert a dialing
pause while entering a number.
8 Microphone
9
Make or answer a call using the
handset speakerphone.
During a call, press to switch
between the speakerphone and
the handset.
10
Press to add a space when
entering names.
11
While you have set the dial mode
to pulse and on a call, press to
switch to tone dialing temporarily.
12 1
Press repeatedly to add or
remove 1 in front of the caller ID
log entry before dialing or saving
it to the phonebook.
Press and hold to set or dial your
voicemail number.
a
b
c
d
e
f
g
h
i
j
n
p
o
k
l
m
3
13 /HOME/FLASH
Make or answer a home call.
Answer an incoming home
call when you hear a call
waiting alert.
14 /CELL
Make or answer a cell call.
Answer an incoming cell call
when you hear a call waiting
alert.
15 VOLUME/ /
Review the phonebook when the
phone is not in use.
Increase the listening volume
during a call.
Scroll up while in a menu, or in
the phonebook, caller ID log, or
redial list.
Move the cursor to the right when
entering numbers or names.
VOLUME/ /CID
Review the caller ID log when the
phone is not in use.
Decrease the listening volume
during a call.
Scroll down while in a menu, or
in the phonebook, caller ID log,
or redial list.
Move the cursor to the left when
entering numbers or names.
16 CHARGE light
On when the handset is
charging.
Telephone base overview
1 IN USE light
Flashes when there is an incoming
call, or another telephone sharing
the same line is in use.
On when the handset is in use.
2 CELL 1 and
CELL 2/HEADSET lights
On when the telephone base
is paired and connected with a
Bluetooth device.
Flashes when the telephone
base is in discoverable mode.
3 /FIND HANDSET
Press to page all system
handsets.
4 CELL 1 and CELL 2/HEADSET
Press to connect the paired cell
phones or headset.
Press and hold to add or replace
a cell phone or a headset.
5 Charging pole
a
b
d
c
e
4
Charger overview
1 Charging pole
Display icons overview
The battery icon flashes
when the battery is low and
needs charging.
The battery icon animates
when the battery is charging.
The battery icon becomes
solid when the battery is fully
charged.
ECO The ECO mode activates
automatically to reduce
power consumption when
the handset is within range
from the telephone base.
There are new voicemail
received from your telephone
service provider.
On when the home line is in
use or there is an incoming
home call.
Flashes when there is an
incoming home waiting call.
1
2
There are Bluetooth devices
connected on the cell
devices list.
On when the cell line is in
use or there is an incoming
cell call.
Flashes when there is an
incoming cell waiting call.
NEW There are new caller ID log
entries.
The handset ringer is off.
Handset and Telephone base
lights overview
Handset lights
On when the handset
speakerphone is in use.
CHARGE On when the handset
is charging in the
telephone base or
handset charger.
Telephone base lights
IN USE On when the telephone
line is in use.
On when you are
registering a handset.
Flashes quickly when
there is an incoming call.
Flashes when another
telephone sharing the
same line is in use.
Flashes when you
are deregistering all
handsets.
1/ 2On when a Bluetooth
device is connected to
the base.
Flashes when the
telephone base is in
discoverable mode.
a
5
Connect
You can choose to connect the telephone
base for desktop usage or wall mounting.
NOTES
Use only the adapters provided.
Even if you do not subscribe to any
conventional telephone service, you can
pair a Bluetooth enabled cell phone to
your telephone base (see Bluetooth), and
use the cell line alone without plugging in
a telephone line cord.
Make sure the electrical outlets are not
controlled by wall switches.
The adapters are intended to be correctly
oriented in a vertical or floor mount
position. The prongs are not designed to
hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
TIP
If you subscribe to digital subscriber line
(DSL) high-speed Internet service through
your telephone line, make sure you install
a DSL filter (not included) between the
telephone line cord and telephone wall
jack. Contact your DSL service provider
for more information.
Connect the telephone base
Connect the charger
Mount the telephone base
The telephone comes ready for tabletop
use. If you have already installed the
telephone for tabletop use, unplug the
telephone line cord from the telephone
wall jack, and unplug the telephone base
power adapter from the wall outlet before
mounting your telephone on a wall.
Follow the steps below to mount your
telephone on a wall.
Route the telephone line cord
through the rectangular hole on the
wall mount bracket. Then plug the
two ends of the telephone line cord
into the telephone base and the wall
outlet as shown.
1.
6
Install and charge the battery
Install the battery as shown below.
NOTES
Use only supplied battery.
If the handset will not be used for a long
time, disconnect and remove the battery to
prevent possible leakage.
THIS SIDE UP
THIS SIDE UP
Connect the power adapter to the
telephone base and an electrical
outlet not controlled by a wall switch.
4.
3. Align the grooves on the telephone
base with the tabs on the wall mount
bracket, and then slide it down until it
clicks securely in place.
2 Align the holes on the bracket with
the standard wall plate and slide the
bracket down until it clicks securely in
place.
A
7
Charge the battery
Place the handset in the telephone base
or the charger to charge.
Once you have installed the battery,
the handset LCD display indicates the
battery status (see the table below).
NOTES
For best performance, keep the handset in
the telephone base or charger when not
in use.
The battery is fully charged after 12 hours
of continuous charging.
If you place the handset in the telephone
base or the charger without plugging
in the battery, the screen displays
No battery.
Battery
indicators
Battery
status
Action
The screen
is blank, or
shows Put
in charger
and
flashes.
The battery
has no
charge or
very little
charge. The
handset
cannot be
used.
Charge
without
interruption
(at least
30 minutes).
The screen
shows Low
battery and
flashes.
The battery
has enough
charge to be
used for a
short time.
Charge
without
interruption
(at least
30 minutes).
The screen
shows
HANDSET
X.
The battery
is charged. To keep
the battery
charged,
place it in the
telephone
base or
charger when
not in use.
When it is fully charged, you can expect
the following performance:
Operation Operating time
While in handset
use (talking*) Seven hours
While in
speakerphone
mode (talking*)
Three hours
While not in use
(standby**) Five days
* Operating times vary depending on your actual
use and the age of the battery.
** Handset is not charging or in use.
CHARGE light
remains on when
charging.
8
Before use
After you install your telephone or
power returns following a power outage,
the handset will prompt you to set the
date and time.
Set date and time
Use the dialing keys (0-9) to enter
the month (MM), date (DD) and year
(YY). Then press SELECT.
2. Use the dialing keys (0-9) to enter the
hour (HH) and minute (MM). Then
press or to choose AM or PM.
3. Press SELECT to save.
Check for dial tone
Press /HOME. If you hear a dial tone,
the installation is successful.
If you do not hear a dial tone:
Make sure the installation procedures
described above are properly done.
It may be a wiring problem. If you
have changed your telephone
service to digital service from a
cable company or a VoIP service
provider, the telephone line may need
to be rewired to allow all existing
telephone jacks to work. Contact your
cable/VoIP service provider for more
information.
1.
Operating range
This cordless telephone operates with
the maximum power allowed by the
Federal Communications Commission
(FCC). Even so, this handset and
telephone base can communicate over
only a certain distance - which can
vary with the locations of the telephone
base and handset, the weather, and the
layout of your home or office.
When the handset is out of range, the
handset displays Out of range or and
no pwr at base alternately.
If there is a call while the handset is out
of range, it may not ring, or if it does
ring, the call may not connect well when
you press /HOME or /CELL. Move
closer to the telephone base, and then
press /HOME or /CELL to answer
the call. If the handset moves out of
range during a telephone conversation,
there may be interference. To improve
reception, move closer to the telephone
base.
9
Bluetooth
Your new DS6611 telephone system
with Bluetooth wireless technology has
the following features:
Pair and connect up to a maximum
of two cell phones with the telephone
base to make and receive cell calls.
Only one cell phone can be active on
a call at a time.
Make and receive calls using your
cell phone plan while utilizing the
ease and comfort of your home
telephone system.
Receive phonebook entries from your
cell phone.
IMPORTANT INFORMATION
Refer to the user's manual of your
Bluetooth enabled cell phone for
more information about how that
device uses Bluetooth connectivity.
Bluetooth wireless technology
operates within a short range (a
maximum of approximately 30 feet)
from the telephone base. Keep
connected cell phones within this
range. For optimal performance,
keep your cell phone within 15 feet
of the telephone base while using the
DS6611 cell line.
If your cell phone has poor reception
in your home, the DS6611 cannot
improve the reception. However, if
there is a location in your house with
better reception, you can leave your
cell phone at that location while using
the DS6611 cell line.
If you experience poor sound quality,
place your cell phone closer to the
DS6611 to ensure strong Bluetooth
signal strength. Make sure there are
no physical obstacles between the
DS6611 and the cell phone, such as
large furniture or thick walls.
Charge your cell phone while it
is connected to the telephone
base. Your cell phone's battery will
discharge faster while it is connected
to the telephone base via Bluetooth
wireless technology.
Monitor your cell phone's usage
because minutes are deducted from
your cellular plan for the duration of
all cell calls.
Refer to Bluetooth setup to learn how
to set up and manage your Bluetooth
enabled devices. Refer to Telephone
operation on how to operate your
Bluetooth devices with your new
DS6611 telephone system with
Bluetooth wireless technology. Refer
to Troubleshooting if you experience
difculty using the telephone system.
DS6611 Cellular
signal
Less than 15 feet for
optimal performance
The Bluetooth® word mark and logos are
owned by Bluetooth SIG, Inc. and any use
of such marks by VTech Holdings Limited
is under license. VTech Holdings Limited
is a member of Bluetooth SIG, Inc. Other
trademarks and trade names are those of
their respective owners.
10
Glossary of terms
Below are some terms used in this
user’s manual to help you become
familiar with using your Bluetooth
enabled cell phone and your new DS6611
telephone system.
Bluetooth cell phone - refers to a
Bluetooth enabled cellular telephone.
Cell line - the telephone line associated
with your cell phone service. On your
DS6611 handset, press /CELL to use
the cell line.
Connected - when you pair a Bluetooth
cell phone to the DS6611, it is
automatically connected. When a cell
phone is connected, 1 and/or 2 displays
after on the handset and the
CELL 1 and/or CELL 2/HEADSET
light on the telephone base is on. If a
cell phone loses its connection to the
telephone base, it must be reconnected
before you can use the cell phone with
the DS6611.
Disconnected - when a cell phone is
disconnected, the on the handset
no longer displays and the CELL 1
and/or CELL 2/HEADSET light on
the telephone base is off.
Discoverable mode - before a
Bluetooth enabled device can be paired,
it must be set to this mode. When
pairing your cell phone, the telephone
base will be set to this mode. Depending
on the manufacturer, this mode is
sometimes referred to as Find Me or
Visibility.
Home line - your conventional
telephone land line. On your DS6611
handset, press /HOME/FLASH to use
the home line.
Paired device - once a Bluetooth
enabled cell phone has been paired
with the telephone base, it appears
on the cell devices list. A maximum of
two cell phones can be paired with the
telephone base.
Pairing - this refers to the process of
Bluetooth enabled cell phone registering
device information with each other.
The telephone base must be paired
with the Bluetooth enabled cell phone
before it can be used. Depending on the
manufacturer, this is also referred to as
Bonding.
PIN - by default, the PIN is 0000 for the
telephone base and for most Bluetooth
devices. PIN information must be
exchanged between Bluetooth devices
before they can be used. This is also
known as a Passkey or Passcode.
11
Bluetooth setup
To use a Bluetooth enabled cell phone
with your DS6611, you must first pair and
connect it with the telephone base. All
DS6611 handsets can be used to make or
answer on the cell phone line.
Bluetooth wireless technology operates
within a short range (30 feet). When
you pair a Bluetooth cell phone to the
telephone base, move closer to the
telephone base to maintain sufficient
signal strength. For optimal performance,
keep your cell phone within 15 feet of the
telephone base while using the cell line.
VTech Connect to CellTM
application
If you are using Bluetooth enabled
Android® phones (OS 2.3 or higher), you
can further extend the flexibility of your
telephone system with use of this
free application.
VTech Connect to Cell comprises
Caller ID manager and Alerts manager
that help you integrate your cell phone
with your new DS6611.
To learn more
or download this
application via Google
Play® Store, Scan the
QR code on the right, or
go to
http://www.vtechphones.com/app_connect_to_cell.
Android® and Google Play® are registered
trademarks of Google Inc.
Add a Bluetooth enabled cell
phone
Before you begin, make sure that
you have cellular coverage and your
Bluetooth enabled cell phone is not
connected to any other Bluetooth
devices. Refer to your cell phone user's
manual to learn how to search for or
add new Bluetooth devices.
All paired cell phones are shown on the
cell devices list.
Once you have paired and connected a
device with the telephone base, you do
not need to repeat the procedure again
unless you want to replace the existing
paired cell phone with a new one.
To pair and connect a cell phone:
Choose a slot to pair the cell phone.
Press and hold CELL 1 and/or
CELL 2/HEADSET on the
telephone base for about four
seconds until the CELL 1 and/or
CELL 2/HEADSET light flashes.
If there is already a cell phone in
the slot, the existing cell phone will
be erased from cell devices list.
Turn on the Bluetooth feature of
your cell phone. Once your cell
phone finds your VTech phone
(VTech DS6611), press the
appropriate key on your cell phone to
continue the pairing process.
Your cell phone may prompt you to
enter the PIN of the telephone base.
The default PIN of the telephone
base is 0000.
All cell phones that are connected to
the telephone base are disconnected
temporarily until the pairing process
is complete.
1.
2.
12
When the cell phone is successfully
paired and connected to the telephone
base, the corresponding status icon
(1 or 2) displays. The corresponding
device light ( CELL 1 and/or
CELL 2/HEADSET) turns on.
The pairing process may take up to one
minute. If the pairing process fails, turn
off the Bluetooth feature on your cell
phone and on the DS6611 by pressing
CELL 1/ CELL 2/HEADSET. Then
repeat the steps above to pair and
connect again. In some cases, it may
take you a few attempts to complete the
pairing process.
The steps for the pairing process may
vary for different cell phones. If this
happens, follow the prompts on your cell
phone and your DS6611 to complete the
pairing process.
If you have trouble pairing your cell
phone, it may not be compatible with
your DS6611. Check the Bluetooth
compatibility list at
www.vtechphones.com.
Add a Bluetooth enabled
headset
To pair and connect a headset:
Press MENU on the phone when it is
not in use.
Press or to highlight Bluetooth,
and then press SELECT.
Press or to highlight
Add BT headset, and then press
SELECT. The screen displays
Search headset...
If there is already a cell device in
the slot, the existing cell phone will
be erased from cell devices list..
4. Set your headset to discoverable
mode (refer to the users manual of
your headset on the Bluetooth feature
of your headset). Once your handset
finds your headset, press SELECT.
1.
2.
3.
Enter the PIN of your headset
if required. The PIN for most
Bluetooth devices is 0000 (refer
to the users manual of your
headset), then press SELECT.
5. When the headset is successfully
paired and connected to the
telephone base, the 2 icon displays.
The CELL 2/HEADSET device
light turns on.
The pairing process may take up to one
minute. If the pairing process fails, turn
off the Bluetooth feature on your headset
and on the DS6611 by pressing
CELL 2/HEADSET . Then repeat the
steps above to pair and connect again.
In some cases, it may take you a few
attempts to complete the pairing process.
When a connected headset is charging,
it may disconnect from the telephone
base and the CELL 2/HEADSET light on
the telephone base turns off. For some
headset models, you may need to turn
on the headset and reconnect it to the
telephone base again.
If you have trouble pairing your
headset, it may not be compatible
with your DS6611. Check the
Bluetooth compatibility list at
www.vtechphones.com.
13
Auto connection
A cell device may be disconnected from
the telephone base when:
The Bluetooth feature of your
connected cell device is turned off.
The power of your cell device is
turned off.
Your cell phone is not within range of
the telephone base.
When the Bluetooth feature or power on
the cell device is turned on, or it moves
within range of the base, the base will
try to reconnect to the cell device. If you
disconnect the cell device from the cell
devices list, the base will not attempt
to reconnect unless your cell device is
moved out of range and back in range
again.
Connect a paired cell phone or
headset
If you need to connect your paired cell
phone or headset to the telephone
base manually:
Press CELL 1 and/or
CELL 2/HEADSET on the
telephone base when it is not in
use. The CELL 1 and/or
CELL 2/HEADSET light flashes.
When the cell phone or headset is
connected to the telephone base, you
hear two beeps. The corresponding
status icon ( 1/2) displays.
The corresponding device light
( CELL 1 and/or
CELL 2/HEADSET ) turns on.
1.
2.
Disconnect a paired cell phone
or headset
If you need to disconnect a paired cell
phone or headset from the telephone
base, refer to the user’s manuals of your
cell phone or headset for instructions to
disconnect a Bluetooth device.
If you press and hold CELL 1 and/or
CELL 2/HEADSET on the telephone
base, the existing paired cell phone
in that slot will be erased. See Add a
Bluetooth enabled cell phone and
Add a Bluetooth enabled headset
on how to pair and connect a new cell
phone or headset.
Review the cell devices list
Press MENU on the handset when it
is not in use.
Press or to highlight Bluetooth,
and then press SELECT.
Press or to highlight Device list,
and then press SELECT.
Download phonebook
You can download phonebook entries
to your DS6611 telephone system via
Bluetooth wireless technology. Each
downloaded phonebook are stored in
the handset phonebook with up to
24 digits for each phone number and
15 characters for each name.
Before downloading the phonebook,
make sure the cell phone is paired and
connected to the DS6611. Make sure the
handset battery is charged for at least
10 minutes.
Place your cell phone next to the
telephone base while downloading.
1.
2.
3.
14
To download a cell phone phonebook:
Press MENU on the phone when it is
not in use.
Press or to highlight Bluetooth,
and then press SELECT.
Press or to highlight Download
PB, and then press SELECT. The
handset displays Select a device
briefly.
If there is no cell phone paired to
the system, the handset displays
Pair cell first and then returns to
the previous menu.
Press or to highlight a desired
device when necessary, and then
press SELECT.
If the selected device is not
available, the handset displays
DX not avail and then returns to
the previous menu.
During the download, the handset
flashes Downloading...
All other idle system handsets display
Downloading...
When the downloading process
completes or when the memory is
full, the handset displays Entries
added: XXX. Then the handset
returns to the Bluetooth menu.
Certain cell phones do not support SIM
card download. If this is the case, try
transferring the contacts from your SIM
card to your cell phone memory first,
and then download from your cell phone
memory. For more information on how to
transfer contacts from your SIM card to
your cell phone memory, see the user’s
manual of your cell phone.
When downloading the phonebook from
your Bluetooth enabled cell phone, some
data may not transfer. For example, if you
have home, mobile and work numbers for a
particular contact, the three categories may
not transfer to your DS6611.
For certain cell phones, you may need to
press a key on your cell phone to confirm
the phonebook download.
1.
2.
3.
4.
5.
For Android and
Blackberry cell
phones, you may also
download your cell
phone phonebook to
your DS6611 via the
VTech Contact Share
application. Scan the QR
code on the right, or go to
www.vtechphones.com/apps/contact_share
for application download.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53

VTech DS6611-3 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur

dans d''autres langues