VTech DS6611 Manuel utilisateur

Marque: VTech

Modèle: DS6611

Catégorie: Téléphones

Taper: Manuel utilisateur

DS6611

DS6611-2

DS6611-3

DECT 6.0 cordless telephone with

BLUETOOTH® wireless technology

Go to www.vtechphones.com (US)

to register your product for enhanced

warranty support and latest VTech

product news.

Go to phones.vtechcanada.com (CA) for

latest VTech product news.

Abridged user’s manual

Scan the QR code for

support information

DS6611-X (CA)

DS6611-X (US)

Important safety

instructions

When using your telephone equipment, basic safety precautions

should always be followed to reduce the risk of ﬁre, electric shock

and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth for

cleaning.

4. CAUTION: Do not install the telephone base at a height

above 2 meters.

5. Do not use this product near water such as near a bath tub,

wash bowl, kitchen sink, laundry tub or a swimming pool, nor in

a wet basement or shower.

6. Do not place this product on an unstable table, shelf, stand or

other unstable surfaces.

7. Avoid placing the telephone system in places with extreme

temperature, direct sunlight, or other electrical devices. Protect

your phone from moisture, dust, corrosive liquids and fumes.

8. Slots and openings in the back or bottom of the telephone base

and handset are provided for ventilation. To protect them from

overheating, these openings must not be blocked by placing

the product on a soft surface such as a bed, sofa or rug. This

product should never be placed near or over a radiator or heat

proper ventilation is not provided.

9. This product should be operated only from the type of power

source indicated on the marking label. If you are not sure of

the type of power supply in your home or ofﬁce, consult your

dealer or local power company.

10. Do not allow anything to rest on the power cord. Do not install

this product where the cord may be walked on.

11. Never push objects of any kind into this product through the

slots in the telephone base or handset because they may touch

dangerous voltage points or create a short circuit. Never spill

liquid of any kind on the product.

12. To reduce the risk of electric shock, do not disassemble this

product, but take it to an authorized service facility. Opening

or removing parts of the telephone base or handset other than

speciﬁed access doors may expose you to dangerous voltages

or other risks. Incorrect reassembling can cause electric shock

when the product is subsequently used.

13. Do not overload wall outlets and extension cords.

14. Unplug this product from the wall outlet and refer servicing to

an authorized service facility under the following conditions:

• When the power supply cord or plug is damaged or

frayed.

• If liquid has been spilled onto the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operation instructions. Improper

adjustment of other controls may result in damage and

often requires extensive work by an authorized technician

to restore the product to normal operation.

• If the product has been dropped and the telephone base

and/or handset has been damaged.

• If the product exhibits a distinct change in performance.

15. Avoid using a telephone (other than cordless) during an

electrical storm. There is a remote risk of electric shock from

lightning.

16. Do not use the telephone to report a gas leak in the vicinity of

the leak. Under certain circumstances, a spark may be created

when the adapter is plugged into the power outlet, or

when the handset is replaced in its cradle. This is a common

event associated with the closing of any electrical circuit.

The user should not plug the phone into a power outlet,

and should not put a charged handset into the cradle, if the

phone is located in an environment containing concentrations

of ﬂammable or ﬂame-supporting gases, unless there is

adequate ventilation. A spark in such an environment could

create a ﬁre or explosion. Such environments might include:

medical use of oxygen without adequate ventilation;

industrial gases (cleaning solvents; gasoline vapors; etc.); a

leak of natural gas; etc.

17. Only put the handset of your telephone next to your ear when

it is in normal talk mode.

18. The power adapter is intended to be correctly oriented in a

vertical or ﬂoor mount position. The prongs are not designed to

hold the plug in place if it is plugged into a ceiling, under-the-

table or cabinet outlet.

19. For pluggable equipment, the socket-outlet shall be installed

near the equipment and shall be easily accessible.

20. CAUTION: Use only the batteries indicated in this

manual. There may be a risk of explosion if a wrong type of

battery is used. Use only the supplied rechargeable batteries or

replacement batteries (BT183342/BT283342).Do not dispose of

batteries in a ﬁre. They may explode. Dispose of used battery

according to the instruction. Disconnect the telephone line

from the equipment before open the battery door.

• Do not use the battery in following conditions:

» High or low extreme temperature during use, storage

or transportation.

» Replacement of a battery with an incorrect type that can

defeat a safeguard.

» Disposal of a battery into ﬁre or a hot oven, or

mechanically crushing or cutting of a battery, that can

result in an explosion.

» Leaving a battery in an extremely high temperature

surrounding environment that can result in an explosion

or the leakage of ﬂammable liquid or gas.

» A battery subjected to extremely low air pressure that

can result in an explosion or the leakage of ﬂammable

liquid or gas.

21. Use only the adapter included with this product. Incorrect

adapter polarity or voltage can seriously damage the product.

22. The applied nameplate is located at the bottom or near of the

product. SAVE THESE INSTRUCTIONS

Battery

• Use only the batteries provided or equivalent. To order a

replacement, visit our website at www.vtechphones.com or

call 1 (800) 595-9511. In Canada, go to

phones.vtechcanada.com or call 1 (800) 267-7377.

• Do not dispose of the battery in a ﬁre. Check with local waste

management codes for special disposal instructions.

• Do not open or mutilate the battery. Released electrolyte is

corrosive and may cause burns or injury to the eyes or skin. The

electrolyte may be toxic if swallowed.

• Exercise care in handling batteries in order not to create a short

circuit with conductive materials.

• Charge the battery provided with this product only in

accordance with the instructions and limitations speciﬁed in

this manual.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless telephones):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless telephones and

implanted cardiac pacemakers. Supported by the U.S. Food and

Drug Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless telephones at least six inches from the

pacemaker.

• Should NOT place wireless telephones directly over the

pacemaker, such as in a breast pocket, when it is turned ON.

• Should use the wireless telephone at the ear opposite the

pacemaker.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless telephones.

About cordless telephones

• Privacy: The same features that make a cordless telephone

convenient create some limitations. Telephone calls are

transmitted between the telephone base and the cordless

handset by radio waves, so there is a possibility that the

cordless telephone conversations could be intercepted

by radio receiving equipment within range of the cordless

handset. For this reason, you should not think of cordless

telephone conversations as being as private as those on

corded telephones.

• Electrical power: The telephone base of this cordless

telephone must be connected to a working electrical outlet.

The electrical outlet should not be controlled by a wall

switch. Calls cannot be made from the cordless handset if the

telephone base is unplugged, switched off or if the electrical

power is interrupted.

• Potential TV interference: Some cordless telephones operate

at frequencies that may cause interference to televisions and

VCRs. To minimize or prevent such interference, do not place

the telephone base of the cordless telephone near or on top

of a TV or VCR. If interference is experienced, moving the

cordless telephone farther away from the TV or VCR often

reduces or eliminates the interference.

• Rechargeable batteries: Exercise care in handling batteries

in order not to create a short circuit with conducting material

such as rings, bracelets and keys. The battery or conductor may

overheat and cause harm. Observe proper polarity between

the battery and the battery charger.

• Nickel-metal hydride rechargeable batteries: Dispose of

these batteries in a safe manner. Do not burn or puncture

the battery. Like other batteries of this type, if burned or

punctured, they could release caustic material which could

cause injury.

What’s in the box

Your product package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

Handset overview

1 – Handset earpiece

2 – LCD display

3 – MENU/SELECT

• Show the menu.

• While in a menu, press to select an item, or

save an entry or setting.

4 – OFF/CANCEL

• Hang up a call.

• Silence the ringer temporarily while the

handset is ringing.

•

Press and hold to erase the missed call

indicator while the phone is not in use.

•

Press to return to the previous menu; or press

and hold to return to idle mode, without

making changes.

5 –

• Press repeatedly to show other dialing

options when reviewing a caller ID log entry.

6 – MUTE/DELETE

• Mute the microphone during a call.

• Delete digits or characters while using the

dialing keys.

• Silence the ringer temporarily while the

handset is ringing.

7 – REDIAL/PAUSE

• Press repeatedly to review the redial list.

• Press and hold to insert a dialing pause while

entering a number.

8 – Microphone

9 –

• Make or answer a call using the handset

speakerphone.

• During a call, press to switch between the

speakerphone and the handset.

10 –

• Press to add a space when entering names.

11 –

• While you have set the dial mode to pulse

and on a call, press to switch to tone dialing

temporarily.

12 – 1

• Press repeatedly to add or remove 1 in front

of the caller ID log entry before dialing or

saving it to the phonebook.

• Press and hold to set or dial your voicemail

number.

13 – /HOME/FLASH

• Make or answer a home call.

• Answer an incoming home call when you hear

a call waiting alert.

14 – /CELL

• Make or answer a cell call.

• Answer an incoming cell call when you hear a

call waiting alert.

15 – VOLUME/ /

• Review the phonebook when the phone is

not in use.

• Increase the listening volume during a call.

• Scroll up while in a menu, or in the

phonebook, caller ID log, or redial list.

• Move the cursor to the right when entering

numbers or names.

VOLUME/ /CID

• Review the caller ID log when the phone is not

in use.

• Decrease the listening volume during a call.

• Scroll down while in a menu, or in the

phonebook, caller ID log, or redial list.

• Move the cursor to the left when entering

numbers or names.

16 – CHARGE light

• On when the handset is charging.

Telephone base overview

1 – IN USE light

• Flashes when there is an incoming call, or another

telephone sharing the same line is in use.

• On when the handset is in use.

2 – CELL 1 and CELL 2/HEADSET lights

• On when the telephone base is paired and

connected with a Bluetooth device.

• Flashes when the telephone base is in

discoverable mode.

3 – /FIND HANDSET

• Press to page all system handsets.

4 – CELL 1 and CELL 2/HEADSET

• Press to connect the paired cell phones or

headset.

• Press and hold to add or replace a cell phone

or a headset.

5 – Charging pole

Charger overview

1 – Charging pole

Display icons overview

The battery icon flashes when the

battery is low and needs charging.

The battery icon animates when the

battery is charging.

The battery icon becomes solid

when the battery is fully charged.

ECO The ECO mode activates

automatically to reduce power

consumption when the handset is

within range from the telephone

base.

There are new voicemail received

from your telephone service

provider.

On when the home line is in use or

there is an incoming home call.

Flashes when there is an incoming

home waiting call.

There are Bluetooth devices

connected on the cell devices list.

On when the cell line is in use or

there is an incoming cell call.

Flashes when there is an incoming

cell waiting call.

NEW There are new caller ID log entries.

The handset ringer is off.

Connect

You can choose to connect the telephone base for

desktop usage or wall mounting.

NOTE

• If you subscribe to digital subscriber line (DSL)

high-speed Internet service through your telephone

line, make sure you install a DSL ﬁlter (not included)

between the telephone line cord and telephone

wall jack. Contact your DSL service provider for more

information.

• Use only the adapters provided.

• Even if you do not subscribe to any conventional

telephone service, you can pair a Bluetooth enabled

cell phone to your telephone base (see Bluetooth),

and use the cell line alone without plugging in a

telephone line cord.

TIP

• If you subscribe to digital subscriber line (DSL)

high-speed Internet service through your telephone

line, make sure you install a DSL ﬁlter (not included)

between the telephone line cord and telephone

wall jack. Contact your DSL service provider for more

information.

Connect the telephone base

Connect the charger

Mount the telephone base

The telephone comes ready for tabletop use.

If you have already installed the telephone for

tabletop use, unplug the telephone line cord

from the telephone wall jack, and unplug the

telephone base power adapter from the wall

outlet before mounting your telephone on a wall.

Follow the steps below to mount your telephone

on a wall.

1. Route the telephone line cord through the

rectangular hole on the wall mount bracket.

Then plug the two ends of the telephone

line cord into the telephone base and the

wall outlet as shown.

2. Align the holes on the bracket with the

standard wall plate and slide the bracket

down until it clicks securely in place.

3. Align the grooves on the telephone base

with the tabs on the wall mount bracket, and

then slide it down until it clicks securely in

place.

4. Connect the power adapter to the

telephone base and an electrical outlet not

controlled by a wall switch.

Install and charge the

battery

Install the battery

Install the battery as shown below.

NOTE

• Use only supplied battery.

• If the handset will not be used for a long time,

disconnect and remove the battery to prevent

possible leakage.

Charge the battery

Place the handset in the telephone base or the

charger to charge.

Once you have installed the battery, the handset

LCD display indicates the battery status (see the

table below).

NOTE

• For best performance, keep the handset in the

telephone base or charger when not in use.

• The battery is fully charged after 12 hours of

continuous charging.

Battery

indicators

Battery status Action

The screen

is blank, or

shows Put in

charger and

ﬂashes.

The battery

has no charge

or very little

charge. The

handset cannot

be used.

Charge without

interruption (at

least 30 minutes).

The screen

shows Low

battery and

ﬂashes.

The battery has

enough charge

to be used for a

short time.

Charge without

interruption (at

least 30 minutes).

The screen

shows

HANDSET X.

The battery is

charged. To keep the

battery charged,

place it in the

telephone base

or charger when

not in use.

Before use

After you install your telephone or power returns

following a power outage, the handset or

telephone will prompt you to set the date and time.

Set date and time

1. Use the dialing keys (0-9) to enter the month

(MM), date (DD) and year (YY). Then press

SELECT.

2. Use the dialing keys (0-9) to enter the hour

(HH) and minute (MM). Then press or

to choose AM or PM.

3. Press SELECT to save.

Check for a dial tone:

Press /HOME. If you hear a dial tone, the

installation is successful.

If you do not hear a dial tone:

• Make sure the installation procedures

described above are properly done.

• It may be a wiring problem. If you have

changed your telephone service to digital

service from a cable company or a VoIP

service provider, the telephone line may

need to be rewired to allow all existing

telephone jacks to work. Contact your cable/

VoIP service provider for more information.

Operating range

This cordless telephone operates with the

maximum power allowed by the Federal

Communications Commission (FCC). Even so, this

handset and telephone base can communicate

over only a certain distance - which can vary with

the locations of the telephone base and handset,

the weather, and the layout of your home or

ofﬁce.

When the handset is out of range, the handset

displays Out of range or and no pwr at base

alternately.

If there is a call while the handset is out of range,

it may not ring, or if it does ring, the call may

not connect well when you press /HOME or

/CELL. Move closer to the telephone base,

and then press /HOME or /CELL to answer

the call. If the handset moves out of range

during a telephone conversation, there may be

interference. To improve reception, move closer

to the telephone base.

Bluetooth

To use a Bluetooth enabled cell phone or headset

with your DS6611, you must ﬁrst pair and connect

your Bluetooth cell phone or headset with the

telephone base.

Bluetooth wireless technology operates within

a short range (a maximum of approximately 30

feet). When you pair a Bluetooth cell phone to

the telephone base, place your Bluetooth cell

phone closer to the telephone base to maintain

sufﬁcient signal strength.

NOTE

For optimal performance, keep your cell phone

within 15 feet of the telephone base while using

the cell line.

Pair and connect your Bluetooth enabled

cell phone

1. Choose a slot to pair the cell phone.

Press and hold CELL 1 or

CELL 2/HEADSET on the telephone

base until you hear a conﬁrmation tone,

and the CELL 1 or CELL 2/HEADSET light

ﬂashes.

2. Turn on the Bluetooth feature of your

cell phone. Once your cell phone ﬁnds

your VTech phone (VTech DS6611), press

appropriate key on your cell phone to

continue the pairing process.

• Your cell phone may prompt you to enter

the PIN of the telephone base.

The default PIN of the telephone base is

0000.

When the cell phone is connected to the

telephone base, the corresponding

status icon ( 1 or 2) displays. The

corresponding device light ( CELL 1 or

CELL 2/HEADSET) turns on.

If the pairing fails, turn off the Bluetooth feature

on your cell phone and on the DS6611 by

pressing CELL 1 or CELL 2/HEADSET. Then

repeat the steps above to pair and connect

again. In some cases, it may take you a few

attempts to complete the pairing process.

Pair and connect your Bluetooth enabled

headset

1. Press MENU on the phone when it is not in use.

2. Press or to scroll to Bluetooth, and then

press SELECT.

3. Press or to scroll to Add BT headset, and

then press SELECT. The screen displays Search

headset...

4. Set your headset to discoverable mode.

Once your handset ﬁnds your headset, press

SELECT.

• Enter the PIN of your headset if required.

The PIN for most Bluetooth devices is

0000 (refer to the user’s manual of your

headset), and then press SELECT.

When the headset is successfully paired and

connected to the telephone base, the 2 icon

displays. The CELL 2/HEADSET light turns on.

VTech Connect to CellTM application

This application helps you integrate

your Android phones with your DS6611.

For more information and application

download, scan the QR code on the

right, or go to

https://www.vtechphones.com/app_connect_to_cell.

Download contacts from your Bluetooth

cell phone

1. Press MENU when the phone is not in use.

2. Scroll to Bluetooth, and then press SELECT.

3. Scroll to Download PB, and then press

SELECT.

4. Scroll to select the desired cell phone, and

then press SELECT.

• For certain cell phones, you may need to press a

key on your cell phone to conﬁrm the phonebook

download.

• The performance of phonebook download feature

depends on the compatibility of your Bluetooth

cell phone. Refer to the user’s manual of your cell

phone for more information about how that device

uses Bluetooth connectivity.

• Certain cell phones do not support SIM card

download. If this is the case, transfer the contacts from

your SIM card to your cell phone memory ﬁrst. Then

download from your cell phone memory. For more

information on how to transfer contacts from your

SIM card to your cell phone memory, see the user’s

manual of your cell phone.

• For Android cell phones, you may also

download your cell phone contacts to

your DS6611 via the

VTech Contact Share application.

Scan the QR code on the right, or

go to

www.vtechphones.com/apps/contact_share for

application download.

Using the handset menu

1. Press MENU when the phone is not in use.

2. Press

until the screen displays the

desired feature menu.

3. Press SELECT to enter that menu.

• To return to the previous menu, press CANCEL.

• To return to idle mode, press and hold CANCEL.

Conﬁgure your

telephone

Set language

The LCD language is preset to English. You can

select English, French or Spanish to be used in all

screen displays.

1. Press MENU when the handset is not in use.

2. Scroll to Settings, and then press SELECT

twice.

3. Scroll to choose English, Français or Español.

4. Press SELECT to save.

Set date and time

1. Press MENU when the handset is not

in use.

2. Scroll to Set date/time, and then press

SELECT.

3. Use the dialing keys (0-9) to enter the month

(MM), date (DD) and year (YY). Then press

SELECT.

4. Use the dialing keys (0-9) to enter the hour

(HH) and minute (MM). Then press or

to choose AM or PM.

5. Press SELECT to save.

Temporary tone dialing

If you have pulse (rotary) service only, you can

switch from pulse to tone dialing temporarily

during a call.

1. During a call, press .

2. Use the dialing keys to enter the relevant

number. The telephone sends touch-tone

signals. It automatically returns to pulse

dialing mode after you end the call.

1 set for

DS6611;

2 sets for

DS6611-2;

3 sets for

DS6611-3

Abridged user’s

manual

1 set for DS6611-2;

2 sets for DS6611-3

THIS SIDE UP

CHARGE light

remains on when

charging.

Speciﬁcations are subject to change without notice.

Transmit

frequency

DECT frequency:

1921.536-1928.448 MHz

Bluetooth frequency:

2402.000-2480.000 MHz

Channels DECT: 5

Bluetooth: 79

Nominal effective

range

Maximum power allowed by FCC and IC. Actual operating range may vary

according to environmental conditions at the time of use.

Power

requirement

Handset: 2.4V Ni-MH battery

Telephone base: 6V DC @ 0.4A

Charger: 6V DC @ 0.4A

Memory Phonebook:

1000 memory locations (shared between home and cell lines);

up to 30 digits and 15 characters

Caller ID log:

50 memory locations;

up to 24 digits and 15 characters

Telephones identiﬁed with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of

the Telecommunications Industry Association. Used under license.

Compatible with

Hearing Ai

d T-Coil

TIA-1083

Technical speciﬁcations

The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any

use of such marks by VTech Holdings Limited is under license. VTech Holdings

Limited is a member of Bluetooth SIG, Inc. Other trademarks and trade names are

those of their respective owners.

Frequently asked

questions

The following are the questions most frequently asked

about the cordless telephone. If you cannot ﬁnd the

answer to your question, visit our website at

www.vtechphones.com or call 1 (800) 595-9511 for

customer service. In Canada, go to

phones.vtechcanada.com or call 1 (800) 267-7377.

My telephone

does not work

at all.

Make sure the telephone base is

installed properly, and battery is

installed and charged correctly. For

optimum daily performance, return

the handset to the telephone base

after use.

The display

shows No line. I

cannot hear the

dial tone.

Disconnect the telephone line

cord from your telephone and

connect it to another telephone.

If there is no dial tone on that

other telephone either, then

the telephone line cord may be

defective. Try installing a new

telephone line cord.

If changing telephone line cord

does not help, the wall jack (or

the wiring to this wall jack) may be

defective. Contact your telephone

service provider.

You may be using a new cable or

VoIP service, the existing telephone

jacks in your home may no longer

work. Contact your service provider

for solutions.

The display

shows To

...see manual

alternately. The

handset does not

work at all.

The handset is deregistered from

the telephone base.

Place the handset in the telephone

base to register it back. The

handset shows Registered and you

hear a beep when the registration

process completes. This process

takes about

90 seconds to complete.

I cannot add

and connect my

cell phone or

headset to the

telephone base.

Make sure you have cellular

coverage and the Bluetooth

function of your cell phone or

headset is turned on. See the

user’s manual of your cell phone or

headset for more information.

Make sure that the telephone base

is in discoverable mode.

Carefully follow the pairing

instructions in this manual. Make

sure that your Bluetooth cell phone

or headset is not connected to

any other Bluetooth device, and is

connected to the telephone base

and active on the device list.

Turn off your cell phone or headset,

and then turn it on again.

The cell phone

reception in my

house is poor

and I cannot

connect it to my

DS6611.

If there is a location in your house

with better reception, you can

leave your cell phone at that

location while you use the DS6611

cell line. In order for this to work,

the telephone base must be within

30 feet of the cell phone.

I accidentally set

my LCD language

to Spanish or

French, and I

don’t know how

to change it back

to English.

While the handset is not in use,

press MENU and then enter 364

to change the handset LCD

language back to English.

Need help?

For operations and guides to help you using

your telephone, and for latest information

and supports, go and check the online help

topics and online FAQs.

Use your smartphone or mobile device to

access our online help.

• Go to

https://help.vtechphones.com/ds6611;

• Scan the QR code on the right. Launch

the camera app or QR code scanner app

on your smartphone or tablet. Hold the

device’s camera up to the QR code and

frame it. Tap the notiﬁcation to trigger the

redirection of the online help.

- If the QR code is not clearly displayed,

adjust your camera’s focus by moving

your device closer or further away until

it is clear.

You can also call our Customer Support at 1

(800) 595-9511 [in US] or

1 (800) 267-7377 [in Canada] for help.

For C-UL compliance

only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de blessures

corporelles ou d’électrocution, suivez toujours ces mesures

préventives de base lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les instructions.

2. Observez toutes les instructions et mises en garde

inscrites sur l’appareil.

3. Débranchez ce téléphone de la prise murale avant de

le nettoyer. N’utilisez pas de nettoyeurs liquides ni en

aérosol. N’utilisez qu’un chiffon doux et légèrement

humecté.

4. ATTENTION: Ne pas installer le socle téléphonique à

une hauteur supérieure à 2 mètres.

5. N’utilisez pas ce produit près de l’eau, tel que près d’un

bain, d’un lavabo, d’un évier de cuisine, d’un bac de

lavage ou d’une piscine, ou dans un sous-sol humide ou

sous la douche.

6. Ne déposez pas ce téléphone sur un chariot, support

ou table chancelants. L’appareil pourrait tomber et être

sérieusement endommagé.

7. Évitez d’installer le système téléphonique dans les

endroits soumis à une température extrême, à la lumière

directe du soleil ou à proximité immédiate d’autres

appareils électriques ou électroniques. Protégez votre

téléphone contre les sources d’humidité, la poussière,

les vapeurs et les liquides corrosifs.

8. Le boîtier de l’appareil est doté de fentes et

d’ouvertures d’aération situées à l’arrière ou en dessous.

Aﬁn d’empêcher la surchauffe, ces ouvertures ne

doivent pas être obstruées en plaçant l’appareil

sur un lit, divan, tapis ou autre surface similaires. Ne

placez pas cet appareil à proximité d’un élément de

chauffage ni d’une plinthe électrique. De plus, ne

l’installez pas dans une unité murale ou un cabinet

fermé qui ne possède pas d’aération adéquate.

9. Ne faites fonctionner cet appareil qu’avec le type

d’alimentation indiqué sur les étiquettes de l’appareil.

Si vous ne connaissez pas le voltage de votre maison,

consultez votre marchand ou votre fournisseur

d’électricité.

10. Ne déposez rien sur le cordon d’alimentation. Installez

cet appareil dans un endroit sécuritaire, là où personne

ne pourra trébucher sur la ligne d’alimentation ni le

cordon téléphonique modulaire.

11. N’insérez jamais d’objets à travers les fentes et

ouvertures de cet appareil, car ils pourraient toucher

à des points de tension dangereux ou court-circuiter

des pièces, ce qui constituerait un risque d’incendie

ou d’électrocution. N’échappez pas de liquides dans

l’appareil.

12. Aﬁn de réduire les risques d’électrocution, ne

démontez pas l’appareil, mais apportez-le plutôt

à un centre de service qualiﬁé s’il doit être réparé.

En enlevant le couvercle, vous vous exposez à des

tensions dangereuses ou autres dangers similaires.

Un remontage inadéquat peut être à l’origine d’une

électrocution lors d’une utilisation ultérieure de

l’appareil. Débranchez l’appareil avant de procéder au

nettoyage. Utilisez un chiffon humide et doux.

13. Ne surchargez pas les prises de courant et les rallonges.

14. Débranchez cet appareil de la prise de courant et

communiquez avec le département de service à la

clientèle de VTech dans les cas suivants :

• Lorsque le cordon d’alimentation est endommagé

ou écorché.

• Si du liquide a été échappé dans l’appareil.

• Si l’appareil a été exposé à une source d’humidité

telle que la pluie ou l’eau.

• Si le produit ne fonctionne pas normalement en

respectant les instructions de fonctionnement.

Réglez uniquement les commandes indiquées dans

le les instructions de fonctionnement. Les réglages

incorrects des autres commandes pourraient

provoquer un dommage qui pourrait exiger un

travail exhaustif de la part d’un technicien autorisé

aﬁn de rétablir le fonctionnement normal de

l’appareil.

• Si le produit a été échappé et que le socle et/ou le

combiné a été endommagé.

• Si le produit afﬁche une nette diminution de sa

performance.

15. Évitez d’utiliser un téléphone (autre qu’un sans ﬁl)

pendant un orage. Les éclairs peuvent être à l’origine

d’une électrocution.

16. N’utilisez pas le téléphone pour rapporter une fuite de

gaz à proximité de la fuite. En certaines circonstances,

une ﬂammèche pourrait être provoquée lorsque

l’adaptateur est branché à une prise de courant, ou

lorsque le combiné est déposé sur le socle. Ceci

est un événement commun associé à la fermeture

d’un circuit électrique. L’utilisateur ne devrait pas

brancher le téléphone à une prise de courant, et ne

devrait pas déposer le combiné chargé sur le socle,

si le téléphone se trouve à proximité d’un endroit

comportant des concentrations de gaz inﬂammables, à

moins que la ventilation soit adéquate. Une ﬂammèche

dans un tel endroit pourrait provoquer un incendie

ou une explosion. De tels environnements peuvent

comprendre: des endroits où l’on utilise de l’oxygène

médical sans ventilation adéquate; des gaz industriels

(dissolvants de nettoyage, des vapeurs d’essence,

etc.); une fuite de gaz naturel, etc.

17. Ne placez que le combiné de votre téléphone près de

votre oreille lorsqu’en mode de conversation.

18. Ces adaptateurs ont été conçus pour être orientés en

position verticale ou montés au sol. Les broches ne sont

pas conçues pour maintenir l’adaptateur en place si

celui-ci est barnché dans une prise au plafond ou sous

une table/ armoire.

19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT,

le socle de prise de courant doit etre installe a proximite

du materiel et doit etre aisement accessible.

20. MISE EN GARDE: Il peut y avoir un risque

d’explosion si vous utilisez le mauvais type de

piles pour le téléphone. N’utilisez que les piles

rechargeable inclus ou les piles de rechange

(BT183342/BT283342). N’incinérez pas les piles.

Celles-ci risqueraient d’exploser. Mettre au rebut les

batteries usagées conformément aux instructions du

fabricant. Débrancher les lignes téléphoniques avant le

remplacement des piles.

• Évite d’utiliser la batterie dans les conditions

suivantes:

» des températures extrêmes faibles ou élevées

auxquelles une batterie peut être soumise

pendant l’utilisation, le stockage ou le transport;

» Remplacement d’une batterie par un type

incorrect pouvant supprimer une protection;

» mise au rebut d’une batterie dans un feu ou

dans un four chaud, ou écrasement mécanique

ou coupure d’une batterie, susceptible de

provoquer une explosion;

» maintien d’une batterie dans un environnement

à très haute température pouvant provoquer

une explosion ou la fuite de liquide ou de gaz

inﬂammables;

» batterie soumise à une pression de l’air

extrêmement faible pouvant provoquer une

explosion ou la fuite de liquide ou de gaz

inﬂammables.

21. N’utilisez que les adaptateurs inclus avec ce produit.

L’utilisation d’un adaptateur dont la polarité ou la

tension serait inadéquate risque d’endommager

sérieusement le produit et mettre votre sécurité en

péril.

22. La plaque signalétique appliquée est située au bas ou à

proximité du produit.

CONSERVEZ CES INSTRUCTIONS

Pile

• N’utilisez que la pile incluse ou l’équivalent.

• Ne jetez pas la pile au feu. Vériﬁez les instructions

spéciﬁques de mise aux rebus auprès des autorités

locales.

• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte

qui s’en échapperait est corrosif et pourrait causer

des brûlures ou des blessures aux yeux ou à la peau.

L’électrolyte est toxique si avalé.

• Soyez prudents lorsque vous manipulez les piles aﬁn

d’éviter les courts-circuits provoqués par des matériaux

conducteurs.

• Rechargez la pile incluse avec cet appareil, selon

les instructions et limites spéciﬁées dans ce guide

d’utilisation.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (s’applique uniquement aux

téléphones numériques sans ﬁl) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’,

une ﬁrme de recherche indépendante, a mené une

évaluation pluridisciplinaire des interférences entre les

téléphones sans ﬁl portatifs et les stimulateurs cardiaques

implantés dans l’organisme. Appuyée par l’Administration

des aliments et drogues (FDA) des États-Unis, la ﬁrme WTR

recommande aux médecins :

Avis aux détenteurs de stimulateurs cardiaques

• Ils doivent tenir le téléphone sans ﬁl à une distance d’au

moins six pouces du stimulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl

directement sur le stimulateur cardiaque, tel que dans

une poche de chemise, lorsque celui-ci est en marche.

• Ils doivent utiliser le téléphone sans ﬁl en l’appuyant

sur l’oreille qui se trouve dans la direction opposée au

stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé

de risque pour les détenteurs de simulateurs cardiaques

causés par les gens qui utilisent un téléphone sans ﬁl à

proximité de ceux-ci.

À propos des téléphones sans ﬁl

Conﬁdentialité : Les mêmes caractéristiques qui constituent

des avantages pour les téléphones sans ﬁl afﬁchent

également des restrictions. Les appels téléphoniques

sont transmis entre le combiné sans ﬁl et le socle par

le biais d’ondes radio ; il y a donc la possibilité que vos

conversations téléphoniques sans ﬁl soient interceptées

par des équipements de réception radio se trouvant dans

la portée du combiné sans ﬁl. Pour cette raison, vous ne

devez pas percevoir les communications téléphoniques

sans ﬁl comme étant aussi conﬁdentielles que celles des

téléphones à cordons.

Alimentation électrique : Le socle de ce téléphone sans

ﬁl doit être branché à une prise électrique fonctionnelle.

La prise électrique ne doit pas être contrôlée par un

interrupteur mural. Les appels ne pourront pas être

effectués du combiné sans ﬁl si le socle est débranché ou

mis hors tension ou si le courant est coupé.

Possibilité d’interférences aux téléviseurs : Certains

téléphones sans ﬁl fonctionnent sur des fréquences

pouvant causer des interférences aux téléviseurs et aux

magnétoscopes. Pour réduire ou prévenir de telles

interférences, ne placez pas le socle du téléphone sans

ﬁl près ou sur un téléviseur ou magnétoscope. S’il y

a présence de parasites, il est conseillé d’éloigner le

téléphone sans ﬁl du téléviseur ou du magnétoscope aﬁn

de réduire possiblement les interférences.

Piles rechargeables : Manipulez les piles avec soin aﬁn de

ne pas les court-circuiter avec des bagues, bracelets ou

clés. Les piles ou le conducteur peut surchauffer et causer

des blessures. Respectez la polarité adéquate entre la pile

et le chargeur.

Les bloc-piles rechargeables à l’hydrure métallique de

nickel : Jetez ces blocs-piles de manière écologique et

sécuritaire. Ne les incinérez pas et ne les percez pas. Tel

que les autres piles de ce type, elles pourraient dégager

une matière toxique qui peut causer des blessures

corporelles si elles sont brûlées ou percées.

The RBRC seal

The RBRC seal on the Ni-MH battery indicates

that VTech Communications, Inc. is voluntarily

participating in an industry program to collect

and recycle these batteries at the end of their

useful lives, when taken out of service within

the United States and Canada.

The program provides a convenient alternative to placing

used Ni-MH batteries into the trash or municipal waste, which

may be illegal in your area.

VTech’s participation makes it easy for you to drop off the

spent battery at local retailers participating in the program or at

authorized VTech product service centers. Please call

1 (800) 8 BATTERY® for information on Ni-MH battery

recycling and disposal bans/restrictions in your area. VTech’s

involvement in this program is part of its commitment to

protecting our environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered

trademarks of Call2recycle, Inc.

FCC, ACTA and IC

regulations

FCC Part 15

NOTE: This equipment has been tested and found to

comply with the requirements for a Class B digital device

under Part 15 of the Federal Communications Commission

(FCC) rules. These requirements are intended to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

WARNING: Changes or modiﬁcations to this equipment

not expressly approved by the party responsible for

compliance could void the user’s authority to operate the

equipment.

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation. Privacy

of communications may not be ensured when using this

telephone.

To ensure safety of users, the FCC/ISEDC has established

criteria for the amount of radio frequency energy that

can be safely absorbed by a user or bystander according

to the intended usage of the product. This product has

been tested and found to comply with the FCC/ISEDC

criteria. The handset may be safely held against the ear of

the user. For body worn operation, this handset has been

tested and meets the FCC/ISEDC RF exposure guidelines

when used with the accessories supplied or designated

for this product. Use of other accessories may not ensure

compliance with FCC/ISEDC RF exposure guidelines. The

telephone base shall be installed and used such that parts

of the user’s body other than the hands are maintained at a

distance of approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian

requirement:

CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and

with technical requirements adopted by the Administrative

Council for Terminal Attachments (ACTA). The label

on the back or bottom of this equipment contains,

among other things, a product identiﬁer in the format

US:AAAEQ##TXXXX. This identiﬁer must be provided to

your telephone service provider upon request.

The plug and jack used to connect this equipment to

premises wiring and the telephone network must comply

with applicable Part 68 rules and technical requirements

adopted by ACTA. A compliant telephone cord and

modular plug is provided with this product. It is designed

to be connected to a compatible modular jack that is

also compliant. An RJ11 jack should normally be used for

connecting to a single line. See the installation instructions

in the user’s manual.

The Ringer Equivalence Number (REN) is used to

determine how many devices you may connect to your

telephone line and still have them ring when you are

called. The REN for this product is encoded as the 6th and

7th characters following the US: in the product identiﬁer

(e.g., if ## is 03, the REN is 0.3). In most, but not all areas,

the sum of all RENs should be ﬁve (5.0) or less. For more

information, please contact your telephone service

provider.

This equipment must not be used with Party Lines. If you

have specially wired alarm dialing equipment connected

to your telephone line, ensure the connection of this

equipment does not disable your alarm equipment. If you

have questions about what will disable alarm equipment,

consult your telephone service provider or a qualiﬁed

installer.

If this equipment is malfunctioning, it must be unplugged

from the modular jack until the problem has been

corrected. Replacement to this telephone equipment can

only be made by the manufacturer or its authorized agents.

For replacement procedures, follow the instructions

outlined under the Limited warranty.

If this equipment is causing harm to the telephone

network, the telephone service provider may temporarily

discontinue your telephone service. The telephone service

provider is required to notify you before interrupting

service. If advance notice is not practical, you will be

notiﬁed as soon as possible. You will be given the

opportunity to correct the problem and the telephone

service provider is required to inform you of your right

to ﬁle a complaint with the FCC. Your telephone service

provider may make changes in its facilities, equipment,

operation, or procedures that could affect the proper

functioning of this product. The telephone service

provider is required to notify you if such changes are

planned.

If this product is equipped with a corded or cordless

handset, it is hearing aid compatible.

If this product has memory dialing locations, you may

choose to store emergency telephone numbers (e.g.,

police, ﬁre, medical) in these locations. If you do store or

test emergency numbers, please:

Remain on the line and brieﬂy explain the reason for the

call before hanging up.

Perform such activities in off-peak hours, such as early

morning or late evening.

Industry Canada

This device contains licence-exempt transmitter(s)/

receiver(s) that comply with Innovation, Science and

Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including

interference that may cause undesired operation of the

device.

Privacy of communications may not be ensured when using

this telephone.

The term ‘’IC:‘’ before the certiﬁcation/registration

number only signiﬁes that the Industry Canada technical

speciﬁcations were met.

The Ringer Equivalence Number (REN) for this terminal

equipment is 0.1. The REN indicates the maximum number

of devices allowed to be connected to a telephone

interface. The termination of an interface may consist of any

combination of devices subject only to the requirement

that the sum of the RENs of all the devices not exceed ﬁve.

This product meets the applicable Innovation, Science and

Economic Development Canada technical speciﬁcations.

California Energy

Commission battery

charging testing

instructions

This telephone is set up to comply with the energy-conserving

standards right out of the box. These instructions are intended

for California Energy Commission (CEC) compliance testing

only. When the CEC battery charging testing mode is

activated, all telephone functions, except battery charging, will

be disabled.

To activate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the

power outlet. Make sure all handsets are plugged with

charged batteries before proceeding.

2. While you press and hold /FIND HANDSET, plug the

telephone base power adapter back to the power outlet.

3. After about 20 seconds, when the IN USE light starts

ﬂashing, release /FIND HANDSET and then press it

again within two seconds. The process takes up to one

minute to complete. When the phone successfully enters

the CEC battery charging testing mode, the IN USE light

turns off and all handsets display To register HS... and

...see manual alternately.

If the phone fails to enter this mode, repeat all the steps

mentioned above. The telephone base will be powered up

as normal if you fail to press /FIND HANDSET within two

seconds in Step 3.

To deactivate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from

the power outlet, and then plug it back in. Then the

telephone base is powered up as normal.

2. Place the handset in the telephone base to register

it back. The handset displays Registering.... If the

registration is successful, the handset screen displays

Registered and beeps. The handset is registered with

the telephone base.

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the

holder of a valid proof of purchase (“Consumer” or “you”)

that the Product and all accessories provided in the sales

package (“Product”) are free from defects in material

and workmanship, pursuant to the following terms and

conditions, when installed and used normally and in

accordance with the Product operating instructions. This

limited warranty extends only to the Consumer for Products

purchased and used in the United States of America and

Canada.

What will VTech do if the Product is not free from defects

in materials and workmanship during the limited warranty

period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service

representative will replace at VTech’s option, without charge,

a Materially Defective Product. If we replace the Product,

we may use new or refurbished replacement parts. If we

choose to replace the Product, we may replace it with a new

or refurbished Product of the same or similar design. We will

retain defective parts, modules, or equipment. Replacement

of the Product, at VTech’s option, is your exclusive remedy.

VTech will return the replacement Products to you in working

condition. You should expect the replacement to take

approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for

ONE (1) YEAR from the date of purchase. If VTech replaces a

Materially Defective Product under the terms of this limited

warranty, this limited warranty also applies to the replacement

Product for a period of either (a) 90 days from the date

the replacement Product is shipped to you or (b) the time

remaining on the original one-year warranty; whichever is

longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident,

shipping or other physical damage, improper

installation, abnormal operation or handling, neglect,

inundation, ﬁre, water or other liquid intrusion.

2. Product that has been subjected to contact with liquid,

water, rain, extreme humidity or heavy perspiration,

sand, dirt or the like; but then only to the extent the

damage was not caused by incorrectly securing

the waterproof handset’s protective elements, for

example, failing to properly close a seal), or such

protective elements are damaged or missing (e.g.

a cracked battery door), or subjecting a Product to

conditions beyond its stated speciﬁcations or limits

(e.g. 30 minutes in 1 meter of fresh water).

3. Product that has been damaged due to repair,

alteration or modiﬁcation by anyone other than an

authorized service representative of VTech;

4. Product to the extent that the problem experienced

is caused by signal conditions, network reliability, or

cable or antenna systems;

5. Product to the extent that the problem is caused by

use with non-VTech accessories;

6. Product whose warranty/quality stickers, product serial

number plates or electronic serial numbers have been

removed, altered or rendered illegible;

7. Product purchased, used, serviced, or shipped for

repair from outside the United States of America

or Canada, or used for commercial or institutional

purposes (including but not limited to Products used

for rental purposes);

8. Product returned without a valid proof of purchase

(see item 2 below); or

9. Charges for installation or set up, adjustment of

customer controls, and installation or repair of systems

outside the unit.

How do you get warranty service?

To obtain warranty service in the United States of America,

please visit our website at www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to

phones.vtechcanada.com or dial 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s

manual - a check of the Product’s controls and features may

save you a service call.

Except as provided by applicable law, you assume the risk

of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in

the transport of the Product(s) to the service location. VTech

will return replaced Product under this limited warranty.

Transportation, delivery or handling charges are prepaid.

VTech assumes no risk for damage or loss of the Product

in transit. If the Product failure is VTech assumes no risk for

damage or loss of the Product in transit. If the Product failure

is not covered by this limited warranty, or proof of purchase

does not meet the terms of this limited warranty, VTech will

notify you and will request that you authorize the cost of

replacement prior to any further replacement activity. You

must pay for the cost of replacement and return shipping

costs for the replacement of Products that are not covered by

this limited warranty.

What must you return with the Product to get warranty

service?

1. Return the entire original package and contents

including the Product to the VTech service location

along with a description of the malfunction or

difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model)

and the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement

between you and VTech. It supersedes all other written or

oral communications related to this Product. VTech

provides no other warranties for this Product. The warranty

exclusively describes all of VTech’s responsibilities regarding

the Product. There are no other express warranties. No one is

authorized to make modiﬁcations to this limited warranty and

you should not rely on any such modiﬁcation.

State/Provincial Law Rights: This warranty gives you speciﬁc

legal rights, and you may also have other rights, which vary

from state to state or province to province.

Limitations: Implied warranties, including those of ﬁtness

for a particular purpose and merchantability (an unwritten

warranty that the Product is ﬁt for ordinary use) are limited to

one year from the date of purchase. Some states/provinces

do not allow limitations on how long an implied warranty

lasts, so the above limitation may not apply to you. In no

event shall VTech be liable for any indirect, special, incidental,

consequential, or similar damages (including, but not limited

to lost proﬁts or revenue, inability to use the Product or other

associated equipment, the cost of substitute equipment,

and claims by third parties) resulting from the use of this

Product. Some states/provinces do not allow the exclusion

or limitation of incidental or consequential damages, so the

above limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof of

purchase

Disclaimer and Limitation

of Liability

VTech Communications, Inc. and its suppliers assume no

responsibility for any damage or loss resulting from the

use of this user’s manual. VTech Communications, Inc.

and its suppliers assume no responsibility for any loss or

claims by third parties that may arise through the use of

this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555

Tigard, OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377

in Canada

Telephone operation Make a home call

• Press /HOME or , and then dial the

telephone number.

-OR-

• Enter the telephone number on the handset

or base, and then press /HOME or to dial.

Make a cell call

• Press /CELL on the handset or base.

Enter the telephone number, and then press

/CELL to dial.

-OR-

• Enter the telephone number on the handset

or base, and then press /CELL to dial.

NOTE

• After ﬁrst pressing /CELL, you may need to choose

a cell device. Scroll to select the desired cell device

when necessary, and then press SELECT.

• While using the cell line, place your cell phone

closer to the base, and make sure that there are no

physical obstacles between the base and the cell

phone, such as large furniture or thick walls.

Answer a home/cell call

• Press /HOME, /CELL, , or any dialing key.

End a home/cell call

• Press OFF on the handset, or put the handset to

the base or charger.

Speakerphone

• During a call, press on the handset to switch

between speakerphone and normal handset use.

Volume

• During a call, press /VOLUME/ on the

handset to adjust the listening volume.

NOTE

The handset earpiece volume setting and speakerphone

volume setting are independent.

Mute

The mute function allows you to hear the other

party but the other party cannot hear you.

1. During a call, press MUTE on the handset or

telephone base. The screen displays Muted.

2. Press MUTE again to resume the conversation.

The screen displays Microphone ON.

Call waiting

When you subscribe to call waiting service from

your telephone service provider, you hear an

alert tone if there is an incoming call while you

are on another call.

Call waiting on the home line:

• Press FLASH to put the current call on hold

and take the new call.

• Press FLASH to switch back and forth

between calls.

Call waiting on the cell line:

• Press /CELL 1 or /CELL 2, to put the

current call on hold and take the new call.

• Press /CELL 1 or /CELL 2 to switch back

and forth between calls.

Find handset

Use this feature to ﬁnd all system handsets.

To start paging:

• Press /FIND HANDSET on the telephone

base. All idle handsets ring and display **

Paging **.

To end paging:

• Press /FIND HANDSET again on the

telephone base.

-OR-

• Press /HOME, /CELL, , CANCEL, or any

dialing key on the handset.

-OR-

• Place the handset in the telephone base or

charger.

NOTE

Do not press and hold /FIND HANDSET for

more than four seconds. It may lead to handset

deregistration.

Join a call in progress

You can use up to two system handsets at a

time on a home line call. You can buy additional

expansion handsets (DS6600) for this telephone

base. You can register up to ﬁve handsets to the

telephone base.

• When a handset is on a home call, press

/HOME or on another handset to join the

call.

• Press OFF to exit the call. The call continues

until all handsets hang up.

Intercom

Use the intercom features for conversations

between two devices.

1. Press MENU on your handset when not in use.

2. Press

to scroll to Intercom, and then

press SELECT. Use the dialing keys to enter a

destination device number.

3. To answer the intercom call, press /HOME,

/CELL, , or any dialing key on the

destination handset.

4. To end the intercom call, press OFF or place

the handset back in the telephone base or

charger.

Transfer a call

While on an outside call, you can use the

intercom feature to transfer the call from one

handset to another.

1. Press MENU on your handset during a call.

2. Press

to scroll to Intercom, and then

press SELECT. The current call is put on hold.

Use the dialing keys to enter a destination

device number.

3. To answer the intercom call, press /

HOME, /CELL, , or any dialing key on

the destination handset. You can now have

a private conservation before transferring

the call.

4. To transfer the call, press OFF on the

initiating handset or place the initiating

handset back in the telephone base or

charger.

5. To end the call, press OFF on the destination

handset or place the destination handset

back in the telephone base or charger.

Answer an incoming call during an intercom

call

If you receive an incoming call during an

intercom call, there is an alert tone.

• To answer a home call, press /HOME. The

intercom call ends automatically.

• To end the intercom call without answering

the outside call, press OFF. The intercom call

ends and the telephone continues to ring.

• To answer a cell call, press OFF to end the

intercom call. The telephone continues to

ring. Then press /CELL.

Redial list

Each handset stores the last 10 telephone

numbers dialed. When there are already 10

entries, the oldest entry is deleted to make room

for the new entry.

Review the redial list

1. Press REDIAL when the handset is not in use.

2. Press , , or REDIAL repeatedly until the

desired entry displays.

Dial a redial list entry

• Press /HOME, /CELL, or to dial.

Delete a redial list entry

When the desired redial entry displays, press

DELETE.

Phonebook

The phonebook can store up to 1000 entries,

which are shared by all handsets. Each entry may

consist of a telephone number up to

30 digits, and a name up to 15 characters.

Add a phonebook entry

1. Press MENU when the phone is not in use.

2. Scroll to Phonebook then press SELECT.

3. Press SELECT again to choose Add new

entry.

4. Enter the number.

• Use the dialing keys to enter the number

(up to 30 digits).

5. Press SELECT to move to the name.

6. Use the dialing keys to enter the name (up to 15

characters). Additional key presses show other

characters of that particular key.

7. Press SELECT to save.

While entering numbers and names, you can:

• Press DELETE to erase a digit or character.

• Press and hold DELETE to erase the entire

entry.

• Press or to move the cursor to the left or

right.

• Press and hold PAUSE to insert a dialing pause

(for entering phone numbers only).

• Press 0 to add a space (for entering names

only).

• Press to add ( appears) or to add

# ( appears)

(for entering phone numbers

only)

Review the phonebook

Entries are sorted alphabetically.

1. Press when the phone is not in use.

2. Scroll to browse through the phonebook, or

use the dialing keys to start a

name search (you can enter up to

3 characters for the search).

3. When the desired entry appears, press

or to dial.

Delete a phonebook entry

1. When the desired entry displays, press

DELETE.

2. When the screen displays Delete entry?,

press SELECT.

Delete all phonebook entries:

1. Press MENU when the phone is not in use.

2. Scroll to Phonebook, and then press SELECT.

3. Scroll to Delete all, and then press SELECT

4. When the screen displays Delete all?, press

SELECT.

Edit a phonebook entry

1. When the desired entry displays, press

SELECT.

2. Use the dialing keys to edit the number, and

then press SELECT.

3. Use the dialing keys to edit the name, and

then press SELECT to save.

Dial a phonebook entry

• When the desired entry appears, press

or to dial.

Caller ID

If you subscribe to caller ID service, information

about each caller appears after the ﬁrst or

second ring. If you answer a call before the caller

information appears on the screen, it will not be

saved in the caller ID log.

The caller ID log stores up to 50 entries. Each

entry has up to 24 digits for the phone number

and 15 characters for the name.

If the telephone number has more that

15 digits, only the last 15 digits appear. If the

name has more than 15 characters, only the

ﬁrst 15 characters are shown and saved in the

caller ID log.

Review a caller ID log entry

1. Press CID when the phone is not in use.

2. Scroll to browse through the caller ID log.

When the desired entry appears:

• Press repeatedly to show different

dialing options.

• Press 1 repeatedly if you need to add or

remove 1 in front of the phone number.

3. Press or to dial the displayed number.

Dial a caller ID log entry

• When the desired entry appears, press

or to dial.

Save a caller ID log entry to the phonebook

1. When the desired caller ID log entry

displays, press SELECT.

2. Scroll to To Phonebook then press SELECT.

3. Use the dialing keys to modify the number,

and then press SELECT.

4. Use the dialing keys to modify the name,

and then press SELECT to save.

Delete a caller ID log entry

• When the desired caller ID log entry displays,

press DELETE.

Delete all caller ID log entries

• Press MENU when the phone is not in use.

Scroll to Caller ID log and then press SELECT.

Scroll to Delete all and then press SELECT

twice.

Call block

If you subscribe to caller ID service, you can

set the telephone to block unknown calls and

certain undesired calls.

The call block list stores up to 20 entries.

Block unknown calls

1. Press MENU when the phone is not in use.

2. Scroll to Call block, and then press SELECT.

3. Scroll to Calls w/o num, and then press

SELECT.

4. Scroll to choose Not block or Block, and then

press SELECT.

Add a call block list entry

1. Press MENU when the phone is not in use.

2. Scroll to Call block, and then press SELECT.

3. Scroll to Block list, and then press SELECT.

4. Scroll to Add new entry, and then press

SELECT.

5. Enter the number.

• Use the dialing keys to enter the number

(up to 30 digits).

6. Press SELECT to move to the name.

7. Use the dialing keys to enter the name (up to 15

characters). Additional key presses show other

characters of that particular key.

8. Press SELECT to save.

Review call block list

1. Press MENU when the phone is not in use.

2. Scroll to Call block, and then press SELECT.

3. Scroll to Block list, and then press SELECT.

4. Press SELECT to choose Review.

Edit a call block list entry

1. When the desired entry displays, press

SELECT.

2. Use the dialing keys to edit the number, and

then press SELECT.

3. Use the dialing keys to edit the name, and

then press SELECT to save.

Save a caller ID log entry to call block list

1. When the desired caller ID log entry

displays, press SELECT.

2. Scroll to To Call block then press SELECT.

3. Use the dialing keys to modify the number,

and then press SELECT.

4. Use the dialing keys to modify the name,

and then press SELECT to save.

Delete a call block list entry

• When the desired call block list entry

displays, press DELETE.

Sound settings

Key tone

You can choose from different ringer tones.

1. Press MENU when the handset is not in use.

2. Scroll to Settings, and then press SELECT.

3. Scroll to choose Key tone, and then press

SELECT.

4. Scroll to choose On or Off, and then press

SELECT to save.

Ringer tone

You can choose from different ringer tones.

1. Press MENU when the handset is not in use.

2. Scroll to Ringers, and then press SELECT.

3. Scroll to choose Home ringtone or Cell

ringtone, and then press SELECT.

4. Scroll to sample each ringer tone, and then

press SELECT to save.

NOTE

If you turn off the ringer volume, you will not hear

ringer tone samples.

Ringer volume (handset)

You can adjust the ringer volume level, or turn

the ringer off.

1. Press MENU when the handset is not in use.

2. Scroll to Ringers, and then press SELECT.

3. Scroll to choose Home volume or Cell

volume, and then

press SELECT.

4. Scroll to adjust the volume, and then press

SELECT to save.

NOTE

If the handset ringer volume is set to off, that handset

is silenced for all incoming calls except paging tone.

Temporary ringer silencing

When the telephone is ringing, you can

temporarily silence the ringer of the handset

without disconnecting the call. The next call rings

normally at the preset volume.

• Press OFF or MUTE on the handset. The

handset displays .

Retrieve voicemail from

telephone service

Voicemail is a feature available from most

telephone service providers. It may be included

with your telephone service, or may be optional.

Fees may apply.

Retrieve voicemail

When you received a voicemail, the handset

displays and New voicemail. To retrieve, you

typically dial an access number provided by your

telephone service provider, and then enter a

security code. Contact your telephone service

provider for instructions on how to conﬁgure the

voicemail settings and listen to messages.

Turn off the new voicemail indicators

If you have retrieved your voicemail while away

from home, and the handset still displays the new

voicemail indicators, use this feature to turn off

the indicators.

NOTE

This feature turns off the indicators only, it does not

delete your voicemail messages.

1. Press MENU when the handset is not in use.

2. Scroll to Settings, and then press SELECT.

3. Scroll to Clr voicemail, and then press

SELECT.

Expand your telephone

system

You can add new handsets (DS6600), cordless

headsets or speakerphones to your telephone

system (purchased separately) to your telephone

system. Visit www.vtechphone.com for a list

of compatible devices. Your telephone base

supports a maximum of ﬁve devices.

For more details, refer to the user’s manual that

comes with your DS6600 new handset, cordless

headset or speakerphone respectively.

ECO mode

This power conserving technology reduces power

consumption for optimal battery performance. The ECO

mode activates automatically whenever the handset is

synchronized with the telephone base.

General product care

Taking care of your telephone

Your cordless telephone contains sophisticated

electronic parts, so it must be treated with care.

Avoid rough treatment

Place the handset down gently. Save the original

packing materials to protect your telephone if you ever

need to ship it.

Avoid water

Your telephone can be damaged if it gets wet. Do not

use the handset outdoors in the rain, or handle it with

wet hands. Do not install the telephone base near a

sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power surges

harmful to electronic equipment. For your own safety, take

caution when using electrical appliances during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that should

retain its luster for many years. Clean it only with a dry

non-abrasive cloth. Do not use dampened cloth or

cleaning solvents of any kind.

Handset control key panel:

DS6611-X (US) DS6611-X (CA)

VTech DS6611 Manuel utilisateur

Marque: VTech

Modèle: DS6611

Catégorie: Téléphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech DS6611 User manual

VTech DS6611 Manuel utilisateur

VTech DS6611 Manuel utilisateur

dans d''autres langues

Documents connexes