RPMA1, -B1, -C1 Installation Instructions
2
DISCLAIMER
CSAV, Inc., and its affiliated corporations and subsidiaries
(collectively, "CSAV"), intend to make this manual accurate and
complete. However, CSAV makes no claim that the information
contained herein covers all details, conditions or variations, nor
does it provide for every possible contingency in connection
with the installation or use of this product. The information
contained in this document is subject to change without notice
or obligation of any kind. CSAV makes no representation of
warranty, expressed or implied, regarding the information
contained herein. CSAV assumes no responsibility for
accuracy, completeness or sufficiency of the information
contained in this document.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the RPMA1 does not exceed
50 lbs (22.68 kg).
Measurements: [Millimeters]
Inches
DIMENSIONS
Installation Instructions RPMA1, -B1, -C1
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
RPMA1, -B1, -C1 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
5/32"
(Provided)
R (4)
S (1)
5/32" U (4) V (4)
T (8)
O (1)
3/32"
Q (1)
A (4)
10-24 x 1/4"
(NOT USED) D (4)
M5 x 12mm G (4)
M2.5 x 10mm K (4)
M5 x 12mm M (4)
M4
B (4)
M3 x 10mm E (4)
M6 x 12mm H (4)
M3 x 10mm L (4)
M6 x 12mm N (4)
M6
C (4)
M4 x 10mm F (4)
1/4-20 x 1/2" J (4)
M4 x 10mm P (4)
Installation Instructions RPMA1, -B1, -C1
5
ASSEMBLY AND INSTALLATION
Installing Ceiling Plate and Disassembling
RPMA1
WARNING: IMPROPER INSTALLATION CAN RESULT IN
SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! Structural members MUST be capable of
supporting five times the combined weight of all equipment
being mounted.
1. Install ceiling plate and extension accessories following
installation instruction provided by manufacturer.
2. Insert key into lock and turn to unlock the projector from
RPM head. (See Figure 1)
3. Moving locking lever to "Unlocked" position. (See Figure 1)
4. Remove the RPM head from RPMA1 top. (See Figure 1)
Figure 1
5. Remove and keep four Phillips screws from top of RPMA1.
(See Figure 2)
Figure 2
6. Pull RPMA1 bottom away from RPMA1 top.
Attaching Projector Security Legs
1. Attach the projector security legs (R) to the projector, using
the correct size screws and washers for your specific
projector. (See Figure 3)
Figure 3
2. Add washers (U) to the projector security legs (R). Add
spacers (T) as necessary to level the projector security legs
(R). (See Figure 4)
Figure 4
Attaching Projector to RPMA1 Bottom
1. Align projector and RPMA1 bottom so that the projector is
oriented correctly.
x
2
3
4
x 4
5
x 4
(M) or (N) x 4
(R) x 4
Projector
(U) x 4
(T) x 4
2
RPMA1, -B1, -C1 Installation Instructions
6
2. Remove the paper backing from the adhesive washers (V)
and attach projector to RPMA1 bottom using adhesive
washers (V) and thumbnuts (P) over the security legs (R).
(See Figure 5)
Figure 5
NOTE: An optional SLB bracket may be purchased and used
to attach projector to RPMA1. (See Figure 5)
3. Attach RPMA1 bottom to RPMA1 top using four Phillips
screws removed in Step 5 of Installing Ceiling Plate and
Disassembling RPMA1. (See Figure 6)
Figure 6
Figure 7
4. Move locking lever to "Locked" position. (See Figure 7)
5. Insert key into lock and turn to secure projector to mount.
(See Figure 7)
Attaching RPMA1 to Threaded Pipe
WARNING: IMPROPER INSTALLATION CAN LEAD TO
PROJECTOR FALLING RESULTING IN SERIOUS
PERSONAL INJURY OR DAMAGE TO EQUIPMENT. DO
NOT substitute hardware. Use only the hardware provided by
the manufacturer.
1. Align RPMA1 with end of NTP pipe. (See Figure 8)
2. Thread RPMA1 up onto pipe by turning counterclockwise
until hand tight. (See Figure 8)
Figure 8
(P) x 4 (V) x 4
Security
Legs (R)
Projector
RPMA1
Bottom
Attachment areas if using an
optional SLB bracket.
x 4
3
4
5
1
2
Installation Instructions RPMA1, -B1, -C1
7
Rough Alignment of RPMA1
1. Turn RPMA1 clockwise or counterclockwise until the front of
the RPMA1 and projector is facing target. (See Figure 9)
Figure 9
2. Secure set screw and security Phillips screw under set
screw. (See Figure 9)
Adjustments
The RPMA1 can be adjusted for rotation (yaw), vertical
elevation (pitch), and horizontal tilt (roll).
Figure 10
YAW Adjustment
1. Loosen YAW adjustment locking screw using a #2 Phillips
screwdriver. (See Figure 10)
2. Turn YAW micro-adjustment screw right or left using a #2
Phillips screwdriver until image is properly aligned on target.
3. Tighten YAW adjustment locking screw using a #2 Phillips
screwdriver.
PITCH Adjustment
1. Loosen PITCH adjustment locking screw using a #2 Phillips
screwdriver. (See Figure 11)
2. Turn PITCH micro-adjustment screw right or left using a #2
Phillips screwdriver until image is properly aligned on target.
3. Tighten PITCH adjustment locking screw using a #2 Phillips
screwdriver.
Figure 11
ROLL Adjustment
1. Loosen ROLL adjustment locking screw using a #2 Phillips
screwdriver. (See Figure 12)
2. Turn ROLL micro-adjustment screw right or left using a #2
Phillips screwdriver until image is properly aligned on target.
3. Tighten ROLL adjustment locking screw using a #2 Phillips
screwdriver.
Figure 12
1
Secure set screw,
then Phillips screw
from under set screw.
2
1
3
2
1
2
3
2
1
3
RPMA1, -B1, -C1 Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
P+86-755-8996 9226 ; 8996 9236 ; 8996 9220
F+86-755-8996 9217
8802-000254
2007 Chief Manufacturing
www.chiefmfg.com
04/07
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief RPMB1 Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief RPMB1 Installation guide