brondell P700BB Le manuel du propriétaire

Owner's Manual

PRO SANITIZING

AIR PURIFIER

WITH AG+ TECHNOLOGY

BY AURABEAT

MODELS P700BB/P7004C/APP60/CANP700BB

2

Read this Owner’s Manual for correct

installation, use, and maintenance of this

product. After reading and completing

installation, keep this manual in a place that

is easily accessible.

SAFETY INFORMATION

3 Important Safeguards

PRODUCT FEATURES

6 Main Features

7 Control Panel Detail

8 Five-Stage Puriﬁcation

OPERATION

9 Preparing for First Use

10 Product Operation

MAINTENANCE

12 Filter Life and Cleaning Schedule

13 Cleaning the Air Sensor

14 Replacing the Filters

TECHNICAL INFORMATION

15 Troubleshooting

17 Product Speciﬁcations

18 Warranty

19 Contact Information

TRANSLATIONS

20 Spanish

38 French

BRONDELL PRO SANITIZING AIR PURIFIER WITH

AG+ TECHNOLOGY BY AURABEAT OWNER’S MANUAL

Contents

3

DANGER: If not observed, serious injury or even death may occur as a result.

• Do not use a damaged power plug or plug

into a loose electric outlet.

• Please connect the power plug to a

grounded electrical outlet rated for 120 V ~

60 Hz.

• Do not move the product by pulling on the

power cord.

• Do not handle the product or power plug

with wet hands.

• Do not forcefully bend the power cord or

place heavy objects on it to prevent it from

being damaged or deformed.

• Do not connect and pull out the power plug

or cord repeatedly.

• If the electric outlet is wet, carefully unplug

the product and let the electric outlet dry

completely before subsequent use.

• Unplug the product before cleaning,

repairing, inspecting, or replacing parts.

• Remove any dust or water from the power

plug prior to plugging in.

• Do not plug the product into an electrical

outlet or power strip that is being used by

too many other products. Use an electrical

outlet adequate for the wattage of the

product.

• Unplug the product if it is not going to be

used for a long time.

• If the power cord is damaged – do not

operate the product and do not attempt to

repair, modify, or replace the cord yourself.

Contact the Brondell Service Center toll

free at 888-542-3355 or email us through our

website.

• Do not insert any wires or sharp objects into

any product gaps. This may result in electric

shock, ﬁre, or product damage.

• If the product produces a strange noise,

a burning smell, or emits smoke, unplug it

immediately from the electrical outlet and

contact Brondell. Failure to do so may result

in electric shock or ﬁre.

• Do not place an electronic or gas heater

near the product or place near heating

vent. This may result in ﬁre or product

deformation. Do not place any containers

ﬁlled with water or other liquids, food,

metallic objects, or any ﬂammable material

on top of the product. If foreign material

enters the product, this may result in

electric shock or ﬁre.

• Do not use the product in locations exposed

to excessive moisture or rain and do not

splash water onto the product. Never place

the product in or near water.

• Do not use the product in areas where

ﬂammable gases or combustible materials

are used or stored.

• Do not spray any ﬂammable materials such

as insecticides or air fragrances near or into

the air inlet.

• Do not disassemble, repair, or modify the

product yourself. If repair is needed please

contact the Brondell Service Center toll

free at 888-542-3355 or email us through our

website.

• Clean the exterior with a damp cloth. Do not

clean the product using benzene, thinner, or

abrasives.

• Do not use the product in a factory or

industrial setting where machine oil may be

present in the air.

SAFETY INFORMATION

Important Safeguards

READ ALL INSTRUCTIONS BEFORE USING

BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION

TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.

4

WARNING: To reduce the risk of ﬁre, electric shock or injury, read

and understand this user guide before operating this product.

• Do not insert ﬁngers or foreign objects into

the air inlet or air outlet.

• Do not let children play with the product or

climb on it. Children should be supervised

to ensure that they do not play with the

product.

• When removing the front cover, exercise

caution that no clothing or body parts

become stuck in the top vent of the product.

• This product can be used by children, age

8 years and up, and persons with reduced

physical or mental capabilities if they have

been given supervision or instruction

concerning use of the product in a safe way

and understand the hazards involved.

• Cleaning and user maintenance shall not be

performed by children without supervision.

• Do not run cord under carpeting. Do not

cover cord with throw rugs, runners, or

similar coverings. Do not route cord under

furniture or appliances. Arrange cord away

from trac area and where it will not be

tripped over.

• Lack of proper cleaning and maintenance

may result in ﬁre, electric shock, or injury.

• Unplug or disconnect the product from the

power supply before servicing.

• This product has a polarized plug (one

blade is wider than the other). To reduce

the risk of electric shock, this plug is

intended to ﬁt in a polarized outlet only

one way. If the plug does not ﬁt fully in the

outlet, reverse the plug. If it still does not

ﬁt, contact a qualiﬁed electrician. Do not

attempt to defeat this safety feature.

SAFETY INFORMATION

Important Safeguards

READ ALL INSTRUCTIONS BEFORE USING

BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION

TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.

5

CAUTION: If not observed, minor physical injury

or property damage may occur as a result.

• Do not install the product on a sloped or

uneven surface.

• Do not apply force or impact to the product.

• Install the product so that no obstacles

block the circulation of air around the

product.

• Install the product away from strong

artiﬁcial lighting or direct sunlight. Do not

install the product in a location exposed to

direct sunlight.

• Replace the ﬁlters according to the ﬁlter

replacement cycle.

SAFETY INFORMATION

Important Safeguards

READ ALL INSTRUCTIONS BEFORE USING

BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION

TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.

6

PRODUCT FEATURES

Main Features

Control Panel

Allows user to

control all functions

of the air puriﬁer

Power Cord Port

Port to insert the

power cord

Air Outlet

Clean, ﬁltered air

is expelled from

the unit

Air Quality Indicator

Color spectrum

indicates the air quality

Front Panel

Remove this to

change the ﬁlters

Air Intake Grille

Air in the room is taken

into the unit through

the vent holes in the

front panel

Handle

Allows the user to

carry the air puriﬁer

from room to room

as needed

Air Quality Sensor

Measures the air

quality

7

Timer

Touch to activate the Timer.

User can set the unit to stay

on for 1 to 12 hours.

PRODUCT FEATURES

Control Panel Detail

Power Button

Touch to turn

power on/o.

Sleep Mode

Touch to engage

Sleep Mode.

UV

Touch to turn

UV on/o.

Digital Display

Displays PM2.5 level,

timer hours, fan speed,

ﬁlter usage.

Filter Check Indicator

The red ﬁlter check icon

will appear when it is

time to check the health

of the ﬁlters.

Child Lock

Touch to lock/

unlock all control

panel buttons.

Plasma

Touch to turn the

Plasma function

on/o.

Air Speed Selector

The unit powers on in Auto Mode

(P0). Touch to select between

three air speed modes: LOW

(P1), MEDIUM (P2), HIGH (P3). To

reselect Auto Mode, touch the

button a fourth time.

8

PRODUCT FEATURES

Five-Stage Air Puriﬁcation

STAGES 13: FILTER PURIFICATION

1. Pre-Filter

Prevents large particles such as dander,

hair and lint from passing through the

system.

2. High Eciency AG+ Air Filter

This HEPA Grade eectively ﬁlters small

particles such as dust, smoke, pollen and

mold, allergens and harmful PM2.5 as small

as 0.01 microns, which includes viruses and

bacteria.

3. Nanocrystalline Air Filter

Natural nanocrystalline minerals absorb

harmful gases, formaldehyde, benzene,

ammonia, VOCs and other odor-rich

pollutants between 0.4 – 0.62 nanometers.

STAGE 4: UV DISINFECTION

UV lamp helps to sanitize the air and

the insides of the unit.

STAGE 5: PLASMA SANITIZATION

Generates positive and negative

ions that, when released into the air,

change the air’s energy, eectively

destroying microorganisms.

1

2

3

9

1. Remove the front panel by pulling it away

from the base unit.

2. Remove all the plastic packaging from

the ﬁlters.

3. Put the ﬁlters back in the unit in the

following order:

a) Nanocrystalline Filter

b) High Eciency AG+ Air Filter

Note: Make sure the cloth tabs on both ﬁlters

that indicate “Front” are facing outward.

4. Re-attach the front panel by inserting the

tabs on the bottom of the front panel into

the slots at the bottom base of the unit.

Push the top of the panel towards the unit;

a magnetic closure ensures the front panel

clicks securely into place.

Note: If the unit is plugged in, it will chime and

the Power button will begin blinking red when

the front panel is secured into place.

OPERATION

Preparing for First Use

Be sure to remove all plastic packaging from the ﬁlters before use.

Step 1

Step 4

Step 3

ab

10

Turning the Brondell Pro Sanitizing Air

Puriﬁer On

1. Insert the power cord into the power cord

port on the back of the unit and plug the

unit into the nearest power outlet.

2. Touch the red blinking Power

button on the top of the control

panel to turn the unit on. The unit

will chime and the control panel

will illuminate.

The unit will start in Auto Mode and begin to

sense the air quality in the room. Once the

air quality has been determined, the PM2.5

value will display on the control panel and

the unit will regulate to an appropriate fan

speed.

The airﬂow is adjusted according to PM2.5.

Auto Mode is set as follows:

3. To turn the Brondell Pro Sanitizing Air

Puriﬁer o, press the Power button.

The unit will chime and power o.

Selecting the Operating Mode

Air Speed – Touch the Speed

button to toggle between 3 fan

speeds: P1 (LOW), P2 (MEDIUM),

and P3 (HIGH). Touch the Speed

button a fourth time for Auto

Mode (P0).

Sleep Mode – Touch the Sleep

button to enter Sleep Mode.

Fan speed will power down to

the lowest level, the air quality

indicator light will turn o, and all

lights on the control panel will turn o

except for the Sleep button. Touch the

Sleep button again to disengage

Sleep Mode.

UV – Touch the UV button to

activate UV sanitization. The UV

light inside the machine will turn

on. To turn o UV sanitization,

touch the UV icon.

Plasma – Touch the Plasma

button to initiate the unique

Plasma generation. The unit will

emit positive and negative ions

into the air, creating enough

energy to disturb bonds and destroy

microorganisms. These negative ions will

remove smoke, dust, and odors from the air

while improving air quality and health.

OPERATION

Product Operation

Place the air puriﬁer on a ﬂat, solid surface. Do not block the Air Outlet with

objects, and remove any heat sources and/or open ﬂames near the unit.

PM2.5

Value

Air

Quality

Level

Air

Quality

Light

Color

Airﬂow

Level

10-79 Good Green 1

80-199 Fair Blue 2

200-500 Bad Red 3

11

OPERATION

Product Operation (Cont’d)

Place the air puriﬁer on a ﬂat, solid surface. Do not block the Air Outlet with

objects, and remove any heat sources and/or open ﬂames near the unit.

Setting the Timer

1. Touch the clock icon to initiate

a timer duration between 1 and

12 hours.

2. Continue to touch the clock icon

until you reach the timer duration desired.

3. To disengage the Timer before the end of

the set duration, touch the clock icon until

the Control Panel displays 0.

Setting the Child Lock

1. Touch the lock icon to engage

the Child Lock. When Child Lock

is on, all other buttons will chime

twice when touched and will not

respond to touch commands.

2. Touch and hold the lock icon for 3 seconds

to disengage the Child Lock.

Note: Icon names will only be displayed when

its function is activated. In Sleep mode, only

Sleep will be displayed even if other functions

are activated.

12

MAINTENANCE

Filter Life and Cleaning Schedule

To check the number of hours your ﬁlter set has been in use at any time, touch and hold the lock

icon for 3 seconds while Child Lock is not in use. The Air Quality Sensor display will show the

amount of hours the current ﬁlter set has been active.

The Filter Check Indicator light on the Brondell Pro Sanitizing Air Puriﬁer is programmed to

illuminate every 2000 hours the unit is in use, however, ﬁlters lasts 8-12 months and should be

replaced at least once annually. If the ﬁlters are cleaned properly and on schedule, the Filter

Check Indicator light could go on 3 or more times before you actually have to replace ﬁlters.

Regular cleaning when air quality is extremely poor is needed.

Proper care and maintenance of the Brondell Pro Sanitizing Air Puriﬁer is critical to performance.

The following chart shows recommended cleaning intervals for each part of the unit.

Part Time Method

External body As needed Wipe with clean damp cloth.

Air Intake Every two months Clean with soft brush or cloth.

Air Outlet Every two months Clean with soft brush or cloth.

Air Sensor Every two months First, wipe with a damp cotton swab.

Then wipe dry with a dry cotton swab.

Woven Pre-Filter Every two to

four weeks

Vacuum or rinse thoroughly in warm water.

Do not use heat to dry the woven pre-ﬁlter.

Nanocrystalline

Filter Every two months Expose to sunlight for one to three hours.

High Eciency

AG+ Filter Every two months

Check the ﬁlter color. If the ﬁlter is light

grey, you can reuse another 2000 hours.

If the ﬁlter is dark or black, it is time to

replace it.

UV Light Bulbs Every twelve months Check the UV bulbs to ensure they are

functioning. Follow instructions on page 14.

Filter life may vary according to usage and environment.

Filters sealed in original packaging, unopened, have a shelf life of 5 years.

Replacement ﬁlters are available for purchase at brondell.com.

Cleaning the unit while it is plugged in may result in electric shock, electric spark

and serious injury. Unplug the unit before cleaning or performing maintenance.

13

1. Remove the Air Sensor Cover by pinching

the tab towards the cover to release it.

2. Clean the Air Inlets (a) and Outlet Vents (b)

with a small brush or cotton swab.

3. Wet a cotton swab lightly and clean the

Lens (a), Dust Inlet (b), and Dust Outlet (c).

After cleaning, use a dry cotton swab to

remove any moisture.

4. Re-attach the Air Sensor Cover.

Note: Without regular cleaning of the Air

Sensor, the Brondell Pro Sanitizing Air Puriﬁer

will decline in performance.

MAINTENANCE

Cleaning the Air Sensor

Step 1

Step 2

Step 3

b

a

c

a

b

14

1. Ensure the Brondell Pro Sanitizing Air Puriﬁer is

powered o.

2. Remove the front panel by grasping the

top sides of the panel and pulling it away from the unit.

3. Remove the existing ﬁlters.

4. Remove all plastic packaging from the replacement

ﬁlters. With the front tabs facing out, install ﬁlters in

the following order:

a) Insert the Nanocrystalline ﬁlter by

laying its bottom edges ﬂush against

the ﬁlter cabinet then pushing the ﬁlter ﬁrmly in

place.

b) Insert the High Eciency AG+ Air Filter, with the

front tabs and the woven pre-ﬁlter facing out in the

same manner.

5. Re-attach the front panel by inserting the tabs on the

bottom of the front panel into the slots at the bottom

base of the unit. Push the top of the panel towards the

unit. A magnetic closure ensures the front panel clicks

securely into place.

6. Touch and hold the clock icon for 3 seconds to reset

the Filter Check Indicator light.

Check the Status of the UV Light Bulbs

While replacing the ﬁlters, you may check to ensure all of

the UV Light Bulbs are functioning.

After removing the existing ﬁlters (step 3), re-attach

the front panel and power the unit on. At the bottom of

the front panel the blue UV light from 5 UV bulbs will

emanate through the grille. If all bulbs are functioning,

power the unit o and continue to step 4 of the ﬁlter

replacement process.

If a bulb is out, please call the Service Center at

888-542-3355 or email us at support@brondell.com.

MAINTENANCE

Replacing the Filters

Be sure to remove all plastic packaging from the ﬁlters before use.

Step 5

Step 6

Step 2

Step 4

WARNING:

UV light is harmful to your eyes. Always place

the front panel on the unit before checking the

UV light bulbs and do not look directly at the bulbs

for an extended period of time.

ab

15

If the Brondell Pro Sanitizing Air Puriﬁer appears to be operating abnormally, please

review the troubleshooting tips before calling the Brondell Service Center as most issues

are easily resolved with a few simple steps. If you are unable to resolve the issue after

checking the following items, please call the Service Center at 888-542-3355, Mon-Fri,

9am-5pm PST (English and Spanish spoken), or email us at support@brondell.com.

TECHNICAL INFORMATION

Troubleshooting

Problem Possible Cause(s) Solution(s)

Unit will not

power on

or

The Control

Panel does not

display any

icons

1. The front panel is not

installed correctly.

2. Power cord is not inserted

correctly into the unit’s

cable port.

3. Power cord is not properly

inserted into the electrical

outlet.

4. Power cord or plug is

damaged.

1. Remove the front panel and

attach it to the unit again.

2. Ensure that the power cord is

properly inserted into the cable

port on the back of the unit.

3. Unplug the unit and plug it

back into the electrical outlet.

4. Contact Brondell Customer

Service.

Fan is not

working

1. Unit is not switched on.

2. Motor requires servicing.

1. Ensure that the power cord is

properly inserted into the cable

port and properly plugged into

the outlet. Touch the Power

button.

2. Contact Brondell Customer

Service.

Fan does not

automatically

adjust when the

unit is in Auto

Mode

1. Auto Mode is not selected.

2. Air Sensor is dirty.

3. Air Sensor is broken or

malfunctioning.

1. Touch the Speed button until

the display shows “P0”.

2. Follow the steps on page 13

to clean the Air Sensor.

3. Contact Brondell Customer

Service.

When in Auto

Mode, the

Air Sensor or

PM2.5 indicator

is always red or

high

1. The unit may be impacted by

moisture, oil residue, smoke,

fumes, or aerosolized spray.

2. The Air Sensor is dirty.

3. Power cord is not properly

inserted into the electrical

outlet.

4. Power cord or plug is

damaged.

1. Move the unit to another

location.

2. Follow the steps on page 13

to clean the Air Sensor.

3. Unplug the unit and plug it

back into the electrical outlet.

4. Contact Brondell Customer

Service.

16

TECHNICAL INFORMATION

Troubleshooting (Cont’d)

Problem Possible Cause(s) Solution(s)

Poor

performance,

or not purifying

at optimum

capacity

or

Unit is running

unusually loud

1. Pre-ﬁlter needs cleaning.

2. One or more ﬁlters is due for

replacement.

3. Plastic packaging on ﬁlters

was not removed.

4. Clearance around the

puriﬁer is not adequate for

air ventilation.

5. Missing ﬁlters or the ﬁlters

were installed in the wrong

order.

6. Recommended room size

has been exceeded.

7. Blockage at Air Inlet or Air

Outlet.

1. Vacuum the pre-ﬁlter. Review

the cleaning schedule for all

ﬁlters on page 12.

2. Replace the ﬁlters.

3. Remove the plastic packaging

and put the ﬁlters back in.

4. Ensure that there is clearance

of 20 inches on each side and

4 inches behind in the front of

the unit.

5. Ensure the ﬁlters are installed

in the correct order and facing

the proper direction. See step

4 on page 14 of this manual.

6. Coverage area is 413 sq ft at 4

air changes per hour and 827

sq ft at 2 air changes per hour.

Move the unit to a smaller room

or purchase an additional unit to

cover a larger area.

7. Contact Brondell Customer

Service.

Unpleasant

odor cannot be

eliminated

1. Filters need cleaning.

2. Filters need replacement.

1. The Nanocrystalline ﬁlter

can be reused after exposure

to sunlight. Review the

cleaning process for all ﬁlters

on page 12.

2. Replace the ﬁlters.

A red

rectangular

icon has

appeared on

the control

panel near

the PM2.5 air

quality display

1. The small red rectangular

icon is the Filter Check

Indicator light.

1. Power o the machine and

check the health of the ﬁlters.

Refer to the maintenance

schedule on page 12. To reset

the Filter Check Indicator, turn

the machine on and touch

and hold the Clock icon for 3

seconds.

If the Brondell Pro Sanitizing Air Puriﬁer appears to be operating abnormally, please

review the troubleshooting tips before calling the Brondell Service Center as most issues

are easily resolved with a few simple steps. If you are unable to resolve the issue after

checking the following items, please call the Service Center at 888-542-3355, Mon-Fri,

9am-5pm PST (English and Spanish spoken), or email us at support@brondell.com.

17

TECHNICAL INFORMATION

Product Speciﬁcations

Types Speciﬁcations

Product Name Brondell Pro Sanitizing Air Puriﬁer

with AG+ Technology by Aurabeat

Model P700BB/P7004C/APP60

Voltage 120 V

Frequency 60 Hz

Power 95W

Filtration Grade H12

Room Coverage

1655 sq ft at 1 air exchange per hour

827 sq ft at 2 air exchanges per hour

538 sq ft at 3 air exchanges per hour

413 sq ft at 4 air exchanges per hour

Casing Material High Quality ABS

Airﬂow 247.2 ft3/min (CFM)

Dimensions 24.7 in x 15.4 in x 8.3 in

Weight 19.2 lbs.

Sensor Type PM2.5 Sensor

Max. Noise ≤62 dB

EPA Establishment Number: 98565-CHN-1

18

Brondell products are backed by some of the most comprehensive warranties in the industry. Brondell

warrants that the Brondell Pro Sanitizing Air Puriﬁer with AG+ Technology by Aurabeat shall be free from

defects in material and workmanship under normal use and service.

Residential & Commercial Warranty for Brondell Pro Sanitizing Air Puriﬁer with AG+ Technology by Aurabeat

– 3-year limited warranty.

Includes Base Model numbers: P700BB, P7004C, and APP60

100% Coverage of defects or malfunctions of all electronic parts and labor for the entire product excluding

consumable ﬁlters for the ﬁrst three years from original date of purchase.

Exclusions and Limitations

1. BRONDELL warrants its products to be free from manufacturing defects under normal use and service. This

warranty is extended only to the ORIGINAL PURCHASER.

2. BRONDELL’s obligations under this warranty are limited to repairs or replacement, at BRONDELL’s option,

of products or parts found to be defective, provided that such products were properly installed and used in

accordance with instructions. BRONDELL reserves the right to make such inspections as may be necessary

in order to determine the cause of the defect. BRONDELL will not charge for labor or parts in connection

with warranty repairs for the ﬁrst three years from the date of purchase on all products except those that

may be subject to heavy commercial use limitations.

3. BRONDELL is not responsible for the cost of removal, return (shipping) and/or reinstallation of products.

This warranty does NOT apply to:

• Damage or loss which occurs during shipment.

• Damage or loss sustained through any natural or man-made causes beyond the control of BRONDELL,

including but not limited to ﬁre, earthquake, ﬂoods, etc.

• Damage or loss resulting from negligent or improper installation including installation of a unit in a harsh or

excessively hazardous environment.

• Damage or loss resulting from removal, improper repair, modiﬁcation of the product, or improper

maintenance including damage caused by improper cleaning and exchanging of ﬁlters

• Damage or loss resulting from acts which are not the fault of BRONDELL or which the Product is not

speciﬁed to tolerate.

• Normal wear and tear usage on the appliance or damages and wear to the ﬁlter during use or maintenance.

4. This warranty gives you speciﬁc legal rights. You may have other rights which vary from state to state.

THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY BRONDELL. REPAIR OR REPLACEMENT AS

PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE PURCHASER.

BRONDELL SHALL NOT BE RESPONSIBLE FOR LOSS OF USE OF THE PRODUCT OR FOR OTHER

INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY THE PURCHASER OR

FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL OR COSTS OF REPAIRS BY OTHERS,

OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED ABOVE. EXCEPT TO THE EXTENT PROHIBITED

BY APPLICABLE LAW, ANY IMPLIED WARRANTIES, INCLUDING THAT OF MERCHANTABILITY, ARE

EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS,

SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.

How to Obtain Service

To obtain repair service under this warranty, you must contact an authorized Brondell Service Center to obtain

an RMA (Return Merchandise Authorization) number. Proof of purchase in the form of a copy of the original

receipt must accompany the returned unit for the warranty to be valid. Take or ship the unit pre-paid to the

closest Brondell authorized service center along with the RMA number and proof of purchase. To obtain an

RMA number, contact the Brondell Service Center at 1-888-542-3355 or by email support@brondell.com.

TECHNICAL INFORMATION

Warranty

19

Brondell, Inc.

PO Box 470085

San Francisco, CA

94147-0085

support@brondell.com

www.brondell.com

For questions, contact:

Brondell Customer Service: 1-888-542-3355

Monday – Friday, 9am – 5pm PST

Manufactured by

Brondell, Inc.

PO Box 470085

San Francisco, CA

94147-0085

Research and Development

in Hong Kong

Made in China

Please retain receipt records

for any warranty claims.

Replacement Filter:

PP-41 Pro AG+ Replacement Filter Pack

20

Lea este manual del propietario para conocer

la instalación, el uso y el mantenimiento

apropiados para este producto. Después de

leer y completar la instalación, guarde este

manual en un lugar fácilmente accesible.

INFORMACIÓN DE SEGURIDAD

21 Salvaguardias importantes

CARACTERÍSTICAS DEL PRODUCTO

24 Características principales

25 Detalle del panel de control

26 Puriﬁcación de aire en cinco etapas

FUNCIONAMIENTO

27 Preparación para el primer uso

28 Funcionamiento del producto

MANTENIMIENTO

30 Vida útil del ﬁltro y plan de limpieza

31 Limpieza del sensor de aire

32 Reemplazo de los ﬁltros

INFORMACIÓN TÉCNICA

33 Solución de problemas

35 Especiﬁcaciones del producto

36 Garantía

37 Información de contacto

TRADUCCIONES

2 Inglés

38 Francés

MANUAL DEL PROPIETARIO DEL BRONDELL PRO SANITIZING

AIR PURIFIER CON TECNOLOGÍA AG+ DE AURABEAT

Índice

La page charge ...

brondell P700BB Le manuel du propriétaire

Ce manuel convient également à

brondell P700BB Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents