StarTech RKCONS1716K 16-Port VGA Rackmount LCD Console Mode d'emploi

Marque
StarTech
Modèle
RKCONS1716K 16-Port VGA Rackmount LCD Console
Catégorie
Consoles en rack
Taper
Mode d'emploi
Quick-Start Guide
Product Design
Actual product may vary from photos
Front View
1Handle 5Mounting Bracket (pre installed)
2Port Selection Buttons/
LEDs
6Keyboard LEDs
3Current Port 7Display Menu Buttons
4Rail(s) 8Release Switch
Rear View
Package Contents
• LCD Rackmount Console x 1
• KVM Cables x 16
• M5 Cage Nuts x 8
• M5 Screws x 8
• Regional Power Cords (NA, JP, EU, UK, ANZ) x 5
• Mounting Rails x 2
• Quick-Start Guide x 1
SKU #: RKCONS1716K
16-Port VGA Rackmount LCD Console | 17 in | 1U
For the latest information, specications, and support visit www.startech.com/RKCONS1716K.
Requirements
• 1U of Rack Space
• Grounding Wire
• Power Source
• Up to 16 Computers or Servers
• Phillips Type Screwdriver
Requirements are subject to change. For the latest requirements,
please visit www.StarTech.com/RKCONS1716K.
Installation
• Caution! Double pole / neutral fuse. Disconnect mains before
servicing.
• Always ground the unit before connecting/disconnecting the
Power Cord.
Mounting the LCD Rackmount Console
Note: It’s easier to install the LCD Rackmount Console if another
person helps you with the installation.
Warning: Use caution and proper lifting techniques when
installing the LCD Rackmount Console.
1. Based on the mounting depth of the server rack that you are
using, select the appropriate length of Mounting Rails.
2. Decide where in the server rack you want to install the LCD
Rackmount Console.
3. Insert the M5 Cage Nuts (two per Mounting Post) into the
square Mounting Holes on the Mounting Posts.
4. Align the rear Mounting Bracket Rails with the M5 Cage Nuts
on the corresponding Mounting Post.
5. Insert an M5 Screw (two per Mounting Post) through the rear
Mounting Bracket Rail and into the M5 Cage Nut. Do not
tighten the M5 Screws.
6. With assistance, slide the LCD Rackmount Console into the
server rack guiding the rear Mounting Bracket Rails into the
Rail Assembly.
7. Insert a M5 Screw (two per Mounting Post) through the front
Mounting Bracket Rail into the M5 Cage Nut.
8. Use a Phillips Type Screwdriver to tighten the M5 Screws.
9. Ensure that the rear Rails are properly aligned.
10. Use a Phillips Type Screwdriver to tighten the M5 Screws.
Grounding the LCD Console
Notes: Grounding wires are typically green or green with a yellow
stripe, and should be at least 18 AWG.
Grounding is recommended in all environments and essential in
environments with high levels of electromagnetic interference
(EMI), or frequent electrical surges.
1. Using a Phillips Head Screwdriver, loosen the Grounding
Connection Screw.
2. Attach the Grounding Wire to the shaft of the Grounding
Connection Screw.
3. Tighten the Grounding Connection Screw, making sure not to
over-tighten.
4. Attach the other end of the Grounding Wire (not connected
to the LCD Rackmount Console) to a proper earth-ground
connection.
Connect the Console
Important Considerations
• If you’re installing the Console in a closed or multi-unit rack
assembly, ensure that the environmental conditions are within
the unit’s maximum and minimum specications.
7
2
36
4
5
4
5
1
8
12
3
456
789
Manual Revision: 03/10/2022
1Power Connection Port 6Daisy Chain Port (not supported)
2Power Switch 7USB-A Ports
3Ground Connection Screw 8Console Monitor Port
4Console Mouse Port 9Host Port
5Console Keyboard Port
For manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Quick Start Guide
Safety Measures
• Wiring terminations should not be made with the product and/or electric lines under power.
• Product installation and/or mounting should be completed by a certied professional.
• Please note that the included power cables are for use with this product only and cannot be
used with other electrical devices.
Mesures de sécurité
• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit et/ou les câbles
électriques sont sous tension.
• L’installation et/ou le montage du produit doit être réalisé par un professionnel certié et
dans le respect des normes locales et du code de construction local.
• Veuillez noter que les câbles d’alimentation inclus sont destinés à être utilisés avec ce produit
uniquement et ne peuvent pas être utilisés avec d’autres appareils électriques.
安全対策
• 電源が入っている状態の製品または電線の終端処理を行わないでください。
• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に従い、有資
格の専門業者が行うようにしてください。
• 本製品に付属しております電源ケーブルは、本製品にのみ使用が可能で他の電気機器
には使用できませんのでご注意ください。
Misure di sicurezza
• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le linee elettriche
sotto tensione.
• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un tecnico
professionale certicato che conosca le linee guida locali sulle norme edilizie e sulla sicurezza.
• Si prega di notare che i cavi di alimentazione inclusi sono da utilizzare solo con questo
prodotto e non possono essere usati con altri dispositivi elettrici.
Säkerhetsåtgärder
• Montering av kabelavslutningar får inte göras när produkten och/eller elledningarna är
strömförda.
• Installation och/eller montering får endast göras av behöriga yrkespersoner och enligt
gällande lokala förordningar för säkerhet och byggnormer.
• Observera att de medföljande strömkablarna endast är avsedda för den här produkten och
inte kan användas med andra elektriska apparater.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and
on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Changes or
modications not expressly approved by StarTech.com could void the user’s authority to operate
the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected
names and/or symbols of third-party companies not related in any way to StarTech.com.
Where they occur these references are for illustrative purposes only and do not represent an
endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of their
respective holders.
Warranty Information
This product is backed by a two-year warranty. StarTech.com warrants its products against defects
in materials and workmanship for the periods noted, following the initial date of purchase. During
this period, the products may be returned for repair, or replacement with equivalent products at
our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its
products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers,
directors, employees or agents) for any damages (whether direct or indirect, special, punitive,
incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss,
arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If
such laws apply, the limitations or exclusions contained in this statement may not apply to you.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT
Hoofddorp
The Netherlands
• Consider your airow requirement when selecting a location for
installation.
• The Console should be installed with a balanced mechanical
load.
• It’s recommended that the Console be connected to a power
source with overcurrent protection and supply wiring.
• The Console should be grounded appropriately.
• Installation depth:
1. Connect a Grounding Wire to the Ground Connection Screw
on the LCD Rackmount Console and to the earth-ground
connection.
2. Connect one of the KVM Cables to a Computer or Server
and the other one to the Host Ports on the LCD Rackmount
Console. You can connect up to 16 computers or servers.
3. Connect the appropriate Power Cord for your region to the
Power Connection Port on the LCD Rackmount Console and to
a Power Source.
4. Open the LCD Rackmount Console. For more information about
how to do this, see the “Open the Console” topic.
5. Use the Power Switch to turn on the LCD Rackmount Console.
Note: The LCD Rackmount Console makes two beeping sounds
and the LED ashes three times when turned on.
6. Turn on the connected Computers or Servers.
7. On the Login screen on the LCD Rackmount Console, do one of
the following:
• If you’re using the console for the rst time or you haven’t
set a username and password, leave the text elds blank and
press Enter.
• If you have set a username and password, enter the
information in the corresponding text elds and press Enter.
8. Connect an optional monitor, keyboard, or mouse, connect the
peripherals to the corresponding ports on the console.
Disconnect the Console
1. Power o the connected Computer, Server or KVM.
2. Close the LCD Rackmount Console. For more information about
how to do this, see the “Close the console” section.
3. Use the Power Switch to turn o the LCD Rackmount Console.
Operation
Open the Console
1. Move the Release Switch to the unlocked position.
2. Use the Handle to pull the LCD Rackmount Console out
towards you until you hear the LCD Rackmount Console click
into place.
3. Pull the Display up and position it at the desired angle.
4. Disconnect the Power Cord from the Power Connection Port
on the LCD Rackmount Console.
Note: Always disconnect the Power Cord before disconnecting the
Grounding Wire.
5. Disconnect the KVM Cable connected to a Computer, Server or
KVM.
6. (Optional) Disconnect the Grounding Wire connected to the
Ground Connection Screw on the LCD Rackmount Console.
Close the Console
1. Lower the Display until it’s ush against the Keyboard.
2. Slide the Release Switches on the LCD Rackmount Console
forward and push the LCD Rackmount Console in towards the
rear of the rack.
3. Release the Switches and continue pushing the LCD Rackmount
Console the rest of the way into the rack.
  • Page 1 1
  • Page 2 2

StarTech RKCONS1716K 16-Port VGA Rackmount LCD Console Mode d'emploi

Marque
StarTech
Modèle
RKCONS1716K 16-Port VGA Rackmount LCD Console
Catégorie
Consoles en rack
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents