Simplicity 020541-00 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
Ce manuel convient également à
Not for
Reproduction
Pressure Washer
Operator’s Manual
This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA)
standard PW101-2010 (Testing and Rating Performance of Pressure Washers).
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
MILWAUKEE, WISCONSIN, U.S.A.
Manual No. 318559 Revision B
Not for
Reproduction
2 BRIGGSandSTRATTON.COM
Thank you for purchasing this quality-built Briggs & Stratton® pressure washer. We are pleased that you’ve
placed your condence in the Briggs & Stratton brand. When operated and maintained according to the
instructions in this manual, your Briggs & Stratton pressure washer will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with pressure
washers and how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this
pressure washer could be used for, it is important that you read and understand these instructions thoroughly
before attempting to start or operate this equipment. Save these original instructions for future reference.
This pressure washer requires nal assembly before use. Refer to the Assembly section of this manual for
instructions on nal assembly procedures. Follow the instructions completely.
Where to Find Us
You never have to look far to nd Briggs & Stratton support and service for your pressure washer. Consult your
Yellow Pages. There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality
service. You can also contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet
at BRIGGSandSTRATTON.COM.
Pressure Washer Engine
Model Number _____________________ Model Number ______________________
Revision __________________________ Type Number _______________________
Serial Number ______________________ Code Number _______________________
Date Purchased ___________________
Table of Contents
Operator Safety....................... 3
Assembly............................ 6
Features and Controls ................ 11
Operation........................... 12
Maintenance ........................ 16
Troubleshooting ..................... 23
Warranty ........................... 24
Product Specications ................ 26
Common Service Parts ............... 26
Copyright © 2015. Briggs & Stratton Power Products Group, LLC
Milwaukee, WI, USA. All rights reserved.
BRIGGS & STRATTON POWER PRODUCTS is a registered
trademark of Briggs & Stratton Corporation
Milwaukee, WI, USA
Not for
Reproduction
Operator Safety
Equipment Description
Read this manual carefully and become
familiar with your pressure washer. Know
its applications, its limitations, and any
hazards involved.
This pressure washer operates at a max of 3,100 PSI
(213.7 BAR) and a ow rate of up to 2.8 gallons
(10.6 liters) per minute. This high quality residential
system features 10” (25.4 cm) wheels, axial cam pump
with stainless steel pistons, automatic cool down
system, cleaning tank system, quick connect spray
tips, heavy duty 40’ (12.2 m) hose, and more.
Every eort has been made to ensure that information
in this manual is accurate and current. However, we
reserve the right to change, alter, or otherwise improve
the product and this document at any time without prior
notice.
The Emission Control System for this pressure washer
is warranted for standards set by the Environmental
Protection Agency and the California Air Resources
Board.
This spark ignition system complies with the Canadian
standard ICES-002.
Important Safety Information
Safety Symbols and Meanings
The safety alert symbol indicates a potential
personal injury hazard. A signal word (DANGER,
WARNING, or CAUTION) is used with the alert symbol
to designate a degree or level of hazard seriousness.
A safety symbol may be used to represent the type of
hazard. The signal word NOTICE is used to address
practices not related to personal injury.
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazard which, if not
avoided, could result in minor or moderate injury.
NOTICE address practices not related to personal
injury.
Fire
Explosion
Toxic Fumes
Hot Surface
Moving Parts
Electrical Shock
Slippery Surface
Fall
Kickback
Flying Objects
Fluid Injection
Operator’s Manual
Chemical Burn
Projectile
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting in
death or serious injury.
• DO NOT use caustic liquid with pressure washer.
• Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
WARNING POISONOUS GAS HAZARD.
Engine exhaust contains carbon monoxide,
a poisonous gas that could kill you in
minutes. You CANNOT smell it, see it, or
taste it. Even if you do not smell exhaust fumes, you
could still be exposed to carbon monoxide gas.
Some chemicals or detergents could be harmful if
inhaled or ingested, resulting in death, serious
injury, nausea, fainting or poisoning.
• Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut o.
• ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this
product, get to fresh air RIGHT AWAY. See a doctor. You
may have carbon monoxide poisoning.
• Use a respirator or mask whenever there is a chance
that vapors may be inhaled when using chemicals.
• Read all instructions with mask so you are certain the
mask will provide the necessary protection against
inhaling harmful vapors when using chemicals.
3
Not for
Reproduction
WARNING The engine exhaust from this
product contains chemicals known to the State of
California to cause cancer, birth defects, or other
reproductive harm.
WARNING This product contains lead and lead
compounds, known to the State of California to
cause birth defects or other reproductive harm.
Wash your hands after handling this product.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a re, resulting in
death or serious injury.
Contact with muer area could cause burns
resulting in serious injury.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 ft. (1.5 m) of clearance on all sides of
pressure washer including overhead.
• It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
dened in Section 4442, maintained in eective working
order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.
WARNING Risk of electrocution.
Contact with power source could cause
electric shock or burn resulting in death or
serious injury.
• NEVER spray near power source.
WARNING Use of pressure washer could
create puddles and slippery
surfaces causing you to fall
resulting in death or serious injury.
Kickback from spray gun could cause you to fall
resulting in death or serious injury.
• Operate pressure washer from a stable surface.
• The cleaning area should have adequate slopes and
drainage to reduce the possibility of a fall due to slippery
surfaces.
• Be extremely careful if you must use the pressure
washer from a ladder, scaolding, or any other similar
location.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
WARNING Starter cord kickback (rapid
retraction) will pull hand and arm toward
engine faster than you can let go which
could cause broken bones, fractures,
bruises, or sprains resulting in serious injury.
• NEVER pull starter cord without rst relieving spray gun
pressure.
• When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
• After each starting attempt, where engine fails to run,
always point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
4 BRIGGSandSTRATTON.COM
WARNING Fuel and its vapors are extremely
ammable and explosive which
could cause burns, re or explosion
resulting in death or serious injury.
WHEN ADDING OR DRAINING FUEL
• Turn pressure washer engine OFF and let it cool at least
2 minutes before removing fuel cap. Loosen cap slowly
to relieve pressure in tank.
• Fill or drain fuel tank outdoors.
• DO NOT overll tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before starting
engine.
• Keep fuel away from sparks, open ames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap and ttings frequently for
cracks or leaks. Replace if necessary.
• DO NOT light a cigarette or smoke.
WHEN STARTING EQUIPMENT
• Ensure spark plug, muer, fuel cap, and air cleaner are in
place.
• DO NOT crank engine with spark plug removed.
WHEN OPERATING EQUIPMENT
• DO NOT operate this product inside any building,
carport, porch, mobile equipment, marine applications,
or enclosure.
• DO NOT tip engine or equipment at angle which causes
fuel to spill.
• DO NOT spray ammable liquids.
WHEN TRANSPORTING, MOVING OR REPAIRING
EQUIPMENT
• Transport/move/repair with fuel tank EMPTY or with fuel
shuto valve OFF (0).
• DO NOT tip engine or equipment at angle which causes
fuel to spill.
• Disconnect spark plug wire.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN
TANK
• Store away from furnaces, stoves, water heaters, clothes
dryers, or other appliances that have pilot light or other
ignition source because they could ignite fuel vapors.
Not for
Reproduction
NOTICE High pressure spray could damage fragile
items including glass.
• DO NOT point spray gun at glass when using red (0°)
spray tip.
• NEVER aim spray gun at plants.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
• If you have questions about intended use, ask dealer or
contact qualied service center.
• NEVER operate units with broken or missing parts, or
without protective housing or covers.
• DO NOT by-pass any safety device on this machine.
• DO NOT tamper with governed speed.
• DO NOT operate pressure washer above rated pressure.
• DO NOT modify pressure washer in any way.
• Before starting pressure washer in cold weather, check all
parts of the equipment to be sure ice has not formed there.
• NEVER move machine by pulling on hoses. Use handle
provided on unit.
• This equipment is designed to be used with Briggs &
Stratton Power Products authorized parts ONLY. If
equipment is used with parts that DO NOT comply with
minimum specications, user assumes all risks and
liabilities.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• If cut by uid, call physician immediately. DO NOT treat
as a simple cut.
• DO NOT allow CHILDREN to operate pressure washer.
• NEVER repair high pressure hose. Replace it.
• NEVER repair leaking connections with sealant of any
kind. Replace o-ring or seal.
• NEVER connect high pressure hose to nozzle extension.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
• NEVER aim spray gun at people, animals, or plants.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while machine is
running.
• NEVER use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
• Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING Unintentional sparking could cause
re or electric shock resulting in
death or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
• Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
WARNING Starter and other rotating parts
could entangle hands, hair, clothing, or
accessories resulting in serious injury.
• NEVER operate pressure washer without protective
housing or covers.
• DO NOT wear loose clothing, jewelry or anything that
could be caught in the starter or other rotating parts.
• Tie up long hair and remove jewelry.
CAUTION
Excessively high operating speeds
could result in minor injury.
Excessively low speeds impose a heavy load.
• DO NOT tamper with governor spring, links or other
parts to increase engine speed. Pressure washer
supplies correct rated pressure and ow when running at
governed speed.
• DO NOT modify pressure washer in any way.
WARNING Risk of eye or bodily injury.
Spray could splash back or propel
objects resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
• Always wear protective clothing such as a long-sleeved
shirt, long pants and close-toed shoes.
• NEVER operate pressure washer when barefoot or
wearing sandals or shorts.
5
Not for
Reproduction
Assembly
Read entire operator’s manual before you
attempt to assemble or operate your new
pressure washer.
Your pressure washer requires some assembly and is
ready for use after it has been properly serviced with
the recommended oil and fuel.
If you have any problems with the assembly of your
pressure washer, please call the pressure washer
helpline at (800) 743-4115. If calling for assistance,
please have the model, revision, and serial number from
the identication label available.
Unpack Pressure Washer
1. Remove the parts bag, accessories, and inserts
included with pressure washer.
2. Open carton completely by cutting each corner
from top to bottom.
3. Ensure you have all included items prior to
assembly.
Items in the carton include:
• Main Unit
• High Pressure Hose
• Spray Gun
• Nozzle Extension with Quick Connect Fitting
• Hose Wrap
• Wheels (2)
• Caster Wheels (2)
• Oil Bottle
• Oil Funnel
• Spray Gun Holder Wireform
• Operator’s Manual
• Owner’s Registration Card
• Multi–Colored Spray Tips (4)
• Handle Pin
• Axle Studs (2)
• Retaining Pins (2)
• Flat Washers (4)
• Metal Spring Clips (2)
• Plastic Knob
• Screws (5)
• Hex Key Wrench
To prepare your pressure washer for operation,
you will need to perform these tasks:
1. Fill out and send in registration card.
2. Attach hose wrap, metal spring clips, spray gun
holder wireform and handle pin to main unit.
3. Install wheel kit on main unit.
4. Add oil to engine crankcase.
5. Add fuel to fuel tank.
6. Connect high pressure hose to spray gun and
pump.
7. Connect water supply to pump.
8. Attach nozzle extension to spray gun.
9. Select/attach quick connect spray tip to nozzle
extension.
Attach Accessory Holders
All assembly instructions in this section will be viewing
from engine end of unit.
1. Place hose wrap (A) over holes (B) on end of
main unit. Using provided hex key wrench, attach
hose wrap with three screws (C). Tighten by hand.
2. Insert spray gun holder wireform (D) through holes
on right side of unit frame. Hold wireform in place
and attach a plastic knob (E) from inside of unit.
Tighten by hand.
3. Using provided hex key wrench, attach metal
spring clips (F) to left side panel of unit with
screws (G). Tighten by hand.
E
D
C
A
B
F
G
6 BRIGGSandSTRATTON.COM
Not for
Reproduction
Install Wheel Kit
NOTICE Wheel kit is not intended for over-the-road
use.
Install the wheel kit as follows:
1. Lift corner of pressure washer and slide caster
wheels up into bottom of tubing on each
underside of pressure washer frame.
2. Using a 3/4” (19 mm) wrench, turn nut (A) under
collar of caster wheels to tighten.
3. Slide at washer (B), wheel (C) and another at
washer (B) over axle stud (D).
NOTICE Be sure to install wheel with raised hub
inboard.
4. Lift corner of pressure washer slightly and slide
axle stud through mounting bracket on pressure
washer frame.
5. Insert retaining pin (E) through hole on axle stud.
6. Repeat steps 3 through 5 to secure second wheel.
Moving Pressure Washer
The pressure washer is equipped with a handle
that locks into three dierent positions for your
convenience. With the handle in the upright position,
it makes it easy to push or pull your pressure washer
to the desired location. With the handle in the middle
position, you can tilt the pressure washer back. The
handle also folds down at for storage.
1. Screw handle pin (F) into bracket on left side of
frame (viewing pressure washer from engine end).
2. Pull handle pin out and lift handle to desired
position.
3. Release handle pin and make sure latch (G) locks
into place.
4. Place lock levers on caster wheels in the
OFF (0) position to unlock wheels and move
pressure washer to desired location.
NOTICE Always face pressure washer and push or
pull to desired location. When moving pressure washer
on an incline, always make sure you are uphill from
pressure washer.
5. Place lock levers on caster wheels in the ON (I)
position to lock wheels and keep pressure washer
from moving.
F
G
B
E
C
D
A
7
Not for
Reproduction
Add Engine Oil
1. Place pressure washer on a at, level surface.
2. Clean area around oil ll and remove yellow oil ll
cap.
3. Using oil funnel, slowly pour contents of provided
oil into oil ll opening to the point of overowing at
oil ll cap. DO NOT overll.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
• DO NOT attempt to crank or start the engine before it has
been properly serviced with the recommended oil. This
may result in an engine failure.
4. Replace oil ll cap and fully tighten.
Add Fuel
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). For
high altitude use, see High Altitude.
• Gasoline with up to 10% ethanol (gasohol) is
acceptable.
NOTICE Avoid pressure washer damage.
Failure to follow Operator’s Manual for fuel
recommendations voids warranty.
• DO NOT use unapproved gasoline such as E15 and E85.
• DO NOT mix oil in gasoline or modify engine to run on
alternate fuels.
To protect the fuel system from gum formation, mix in a
fuel stabilizer when adding fuel. See Storage. All fuel is
not the same. If you experience starting or performance
problems after using fuel, switch to a dierent fuel
provider or change brands. This engine is certied to
operate on gasoline. The emission control system for this
engine is EM (Engine Modications).
1. Clean area around fuel ll cap, remove cap.
2. Slowly add unleaded gasoline (A) to fuel tank
(B). Be careful not to ll above the bae (C).
This allows adequate space for fuel expansion as
shown.
3. Install fuel cap and let any spilled fuel evaporate
before starting engine.
High Altitude
At altitudes over 5,000 ft. (1,524 m), a minimum
85 octane / 85 AKI (89 RON) gasoline is acceptable.
To remain emissions compliant, high altitude
adjustment is required. Operation without this
adjustment will cause decreased performance,
increased fuel consumption, and increased emissions.
See an Authorized Briggs & Stratton dealer for high
altitude adjustment information. Operation of the
engine at altitudes below 2,500 ft. (762 m) with the
high altitude kit is not recommended.
FUEL
TANK
C
B
A
WARNING Fuel and its vapors are extremely
ammable and explosive which could
cause burns, re or explosion
resulting in death or serious injury.
WHEN ADDING FUEL
• Turn pressure washer engine OFF and let it cool at least
2 minutes before removing fuel cap. Loosen cap slowly
to relieve pressure in tank.
• Fill fuel tank outdoors.
• DO NOT overll tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before starting
engine.
• Keep fuel away from sparks, open ames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap and ttings frequently for
cracks or leaks. Replace if necessary.
• DO NOT light a cigarette or smoke.
8 BRIGGSandSTRATTON.COM
Not for
Reproduction
Lubricate O-Rings
Lubrication of o-rings is extremely important for
installation and operation. The use of a lubricant
(petroleum or synthetic grease) during assembly helps
seat o-rings properly and provides an improved seal. It
also helps protect the o-ring from damage by abrasion,
pinching or cutting and extends the life of the o-ring.
NOTICE ALWAYS apply a small amount of lubricant
on o-rings prior to assembling the garden hose to the
pump inlet (A), high pressure hose to pump outlet (B),
high pressure hose (C), nozzle extension (D), and
spray gun (E).
Lubricate all connections shown below, following
these instructions:
1. Inspect and clean connecting surfaces prior to
lubrication and assembly.
2. Use lubricants sparingly during assembly; a light
lm is all that is required.
3. Use a small brush or cotton swab to apply grease
directly to o-rings where they are not accessible
(QC tting, M22 tting).
E
A
C
D
B
9
Not for
Reproduction
Connect Hose and Water Supply to Pump
NOTICE DO NOT run the pump without the water
supply connected and turned on.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
NOTICE Remove and discard the shipping caps from
the pump’s high pressure outlet and water inlet before
attaching hoses.
1. Uncoil high pressure hose and attach quick
connect end of hose to base of spray gun. Pull
down on collar of quick connect, slide onto spray
gun and let go of collar. Tug on hose to be sure of
tight connection.
2. Similarly, attach other end of high pressure hose
to high pressure outlet (A) on pump. Pull down
on collar of quick connect, slide onto pump and
let go of collar. Pull on hose to be sure of tight
connection.
3. Before connecting garden hose to water inlet,
inspect inlet screen (B). Clean screen if it contains
debris or have it replaced if damaged. DO NOT
run pressure washer if inlet screen is damaged.
4. Run water through your garden hose for
30 seconds to clean out any debris.
NOTICE DO NOT siphon standing water for the water
supply. Use ONLY cold water (less than 100°F (38°C)).
NOTICE Using a One Way Valve (vacuum breaker
or check valve) at pump inlet could cause pump or
inlet connector damage.
• There MUST be at least 10 ft. (3 m) of unrestricted garden
hose between the pressure washer inlet and any device,
such as a vacuum breaker or check valve.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Connect the garden hose (not to exceed 50 ft.
(15 m) in length) to the water inlet. Tighten by
hand.
6. Turn ON the water, press red button (C) on the
gun and squeeze the trigger to purge the pump
system of air and impurities.
Checklist Before Starting Engine
Review the unit’s assembly to ensure you have
performed all of the following.
1. Be sure to read Operator Safety and Operation
sections before using pressure washer.
2. Make sure handle is in place and secure.
3. Check that oil has been added to proper level in
the engine crankcase.
4. Add proper fuel to fuel tank.
5. Check for properly tightened hose connections.
6. Check to make sure there are no kinks, cuts, or
damage to high pressure hose.
7. Provide a proper water supply at an adequate
ow.
B
C
A
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
• NEVER connect high pressure hose to nozzle extension.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
10 BRIGGSandSTRATTON.COM
Not for
Reproduction
Features and Controls
Read this Operator’s Manual and safety rules before operating your pressure washer.
Compare the illustrations with your pressure washer, to familiarize yourself with the locations of various
controls and adjustments. Save this manual for future reference.
A - Spray Gun — Controls the application of water
onto cleaning surface with trigger device. Includes
trigger lock.
B - High Pressure Hose — Connect one end to water
pump and the other end to spray gun.
C - Cleaning Tank – Use to hold up to 1 gallon
(3.8 liters) of pressure washer safe detergent.
D - Nozzle Extension with Quick Connect — Allows
you to switch between four dierent spray tips.
E - Spark Arrester Muer — Exhaust muer lowers
engine noise and is equipped with a spark arrester
screen.
F - Pump — Develops high pressure.
G - Automatic Cool Down System — Cycles water
through pump when water reaches 125°-155°F
(51°-68°C). Warm water will discharge from pump
onto ground. This system prevents internal pump
damage.
H - Air Filter — Protects engine by ltering dust and
debris out of intake air.
J - Recoil Starter — Used for starting the engine
manually.
K - High Pressure Outlet — Connection for high
pressure hose.
L - Water Inlet — Connection for garden hose.
M - Throttle Lever — Sets engine in starting mode
for electric or manual starting and stops a running
engine.
N - Quick Connect Spray Tips — Detergent, 0°,
15°, and 40°: for various high pressure cleaning
applications.
P - Fuel Valve — Used to turn fuel supply on and o
to engine.
R - Choke Lever — Prepares a cold engine for starting.
S - Fuel Tank — Fill tank with regular unleaded fuel.
Always leave room for fuel expansion.
Items Not Shown:
Identication Label — Provides model and serial
number of pressure washer. Please have these readily
available if calling for assistance.
Oil Drain — Drain engine oil here.
Oil Fill — Check and add engine oil here.
A
D
B
J
L
P
K
L
H
E
C
N
G
,
F
R
M
S
11
Not for
Reproduction
Operation
If you have any problems operating your pressure
washer, please call the pressure washer helpline at
(800) 743-4115.
Pressure Washer Location
Carbon Monoxide Poisoning
Risk of Fire Clearances
How to Start Your Pressure Washer
To start your pressure washer for the rst time, follow
these instructions step-by-step. This starting information
also applies if you have let the pressure washer sit idle
for at least a day.
1. Place pressure washer near an outside water
source capable of supplying water at a ow rate
greater than 3.8 gallons (14.4 liters) per minute
and no less than 20 PSI (1.4 BAR) at pressure
washer end of garden hose. DO NOT siphon
supply water.
2. Check that high pressure hose is tightly connected
to spray gun and pump. See Assembly section.
3. Make sure unit is in a level position.
4. Connect garden hose to water inlet on pressure
washer pump.
NOTICE DO NOT run the pump without the water
supply connected and turned on.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Turn ON water, point gun in a safe direction, press
red button and squeeze trigger to purge pump
system of air and impurities.
6. Attach nozzle extension to spray gun. Tighten by
hand.
7. Choose spray tip you want to use, pull back on
collar of nozzle extension, insert spray tip and
release collar. Tug on spray tip to make sure it is
securely in place. See How to Use Spray Tips.
8. Turn fuel valve (A) to ON (I) position. The fuel
valve handle should be vertical (pointing toward
the ground) for fuel to ow.
9. Move throttle control lever (B) to FAST ( )
position, shown on engine as a rabbit.
A
Exhaust Port
Pointed away from
occupied spaces
B
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank
causing a re, resulting in death or serious
injury.
• Keep at least 5 ft. (1.5 m) clearance on all sides of
pressure washer including overhead.
12 BRIGGSandSTRATTON.COM
WARNING POISONOUS GAS HAZARD.
Engine exhaust contains carbon monoxide,
a poisonous gas that could kill you in
minutes. You CANNOT smell it, see it, or
taste it. Even if you do not smell exhaust fumes, you
could still be exposed to carbon monoxide gas.
• Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut o.
• ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this
product, get to fresh air RIGHT AWAY. See a doctor. You
may have carbon monoxide poisoning.
Not for
Reproduction
10. Move choke lever (A) to CHOKE position.
NOTICE For a warm engine, be sure the choke lever
is in the RUN ( ) position.
NOTICE Before starting the pressure washer, be sure
you are wearing safety goggles as described below.
11. Position yourself as recommended below, grasp
recoil handle and pull slowly until you feel some
resistance. Then pull rapidly to start engine.
Return starter grip handle slowly. DO NOT let
rope “snap back” against starter.
• If engine starts, proceed to step 13.
• If engine fails to start, proceed to step 12.
NOTICE After each starting attempt, where engine
fails to run, always point gun in safe direction, press
red button and squeeze spray gun trigger to release
high pressure.
12. If engine fails to start after six pulls, move choke
lever to RUN (
) position, and repeat step 11.
13. When engine starts, slowly move choke lever to
RUN ( ) position, as engine warms. If engine
falters, move choke lever to CHOKE ( )
position, then to RUN ( ) position.
NOTICE Always keep the throttle control lever in the
FAST ( ) position when operating the pressure
washer.
A
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• DO NOT allow CHILDREN to operate pressure washer.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• NEVER aim spray gun at people, animals, or plants.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while machine is
running.
• NEVER use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
• Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a re, resulting in
death or serious injury.
Contact with muer area could cause burns
resulting in serious injury.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 ft. (1.5 m) of clearance on all sides of
pressure washer including overhead.
• It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
dened in Section 4442, maintained in eective working
order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.
13
WARNING Starter cord kickback (rapid
retraction) will pull hand and arm toward
engine faster than you can let go which
could cause broken bones, fractures,
bruises, or sprains resulting in serious injury.
• NEVER pull starter cord without rst relieving spray gun
pressure.
• When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
• After each starting attempt, where engine fails to run,
always point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
Not for
Reproduction
How to Stop Your Pressure Washer
1. Release spray gun trigger and let engine idle for
two minutes.
2. Move throttle to SLOW ( ) position, then
STOP ( ) position.
3. Turn fuel valve to OFF (0) position.
4. ALWAYS point spray gun in a safe direction,
press red button and squeeze spray gun trigger to
release retained high water pressure.
How to Store Accessories
The unit is equipped with multiple places to store your
spray gun, nozzle extension, high pressure hose and
spray tips.
1. Place spray gun into spray gun holder wireform as
shown.
2. Place nozzle extension into metal spring clips on
side of unit as shown.
3. Coil high pressure hose onto hose wrap.
4. Insert multi–colored spray tips in spaces provided
on side panel.
How to Use Spray Tips
The quick–connect on the nozzle extension allows you
to switch between four dierent quick connect spray
tips. Spray tips can be changed while pressure washer
is running once spray gun trigger lock is engaged. The
spray tips vary the spray pattern as shown.
Follow these instructions to change spray tips:
1. Pull back collar on quick–connect and pull current
spray tip o. Store spray tips in holder provided on
the side panel.
2. Select desired spray tip:
• For delicate rinse, for gentle cleaning of cars/
trucks, boats, RV’s, patio furniture, lawn
equipment, etc., select white 40° spray tip.
• For general rinsing, ideal for most all purpose
cleaning such as home siding, brick patios,
wood decks, driveways and sidewalks, garage
oors, etc., select yellow 15° spray tip.
• For maximum rinsing, for stubborn or hard to
reach surface such as second story surfaces,
paint removal, oil stains, rust removal or other
stubborn substances (tar, gum, grease, wax,
etc.), select red 0° spray tip.
• To apply detergent, applies project specic
cleaners to help break down stubborn dirt and
grime on a variety of surfaces, select black
detergent spray tip.
40° White
2600 PSI
2.8 GPM
15° Yellow
2900 PSI
2.6 GPM
0° Red
3100 PSI
2.4 GPM
Low Pressure
Black
Use to apply detergent
High Pressure
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
• NEVER exchange spray tips without the trigger lock
being engaged on the spray gun.
• DO NOT twist spray tips while spraying.
14 BRIGGSandSTRATTON.COM
Not for
Reproduction
3. Pull back on collar, insert new spray tip and
release collar. Tug on spray tip to make sure it is
securely in place.
Usage Tips
• For most eective cleaning, keep spray tip from
8 to 24 inches (20 to 61 cm) away from cleaning
surface.
• If you get spray tip too close, especially using a
high pressure spray tip, you may damage surface
being cleaned.
• DO NOT get closer than 6 inches (15 cm) when
cleaning tires.
Applying Detergent
To apply detergent, follow these steps:
1. Review use of spray tips.
2. Prepare detergent solution as required by job.
3. Pour detergent solution into cleaning tank.
NOTICE Cleaning tank holds up to 1 gallon (3.8 liters).
4. Make sure black detergent spray tip is installed.
NOTICE Detergent cannot be applied with the high
pressure spray tips (White, Yellow or Red).
5. Make sure garden hose is connected to water
inlet. Check that high pressure hose is connected
to spray gun and pump. Turn on water.
NOTICE You must attach all hoses before you start
engine.
• Starting the engine without all the hoses connected and
without the water turned ON could damage the pump.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
6. Start engine following instructions How to Start
Your Pressure Washer.
7. Rotate detergent shut-o valve on cleaning tank
to ON (I) position.
8. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward,
using long, even, overlapping strokes.
9. Allow detergent to “soak in” for 3-5 minutes
before washing and rinsing. Reapply as needed
to prevent surface from drying. DO NOT allow
detergent to dry on (prevents streaking).
Pressure Washer Rinsing
For Rinsing:
1. Turn detergent shut-o valve to OFF (0) position.
2. Remove black detergent spray tip from nozzle
extension.
3. Select and install desired high pressure spray tip
following instructions How to Use Spray Tips.
4. Keep the spray gun a safe distance from the area
you plan to spray.
5. Apply a high pressure spray to a small area and
then check surface for damage. If no damage
is found, you can assume it is okay to continue
rinsing.
6. Start at top of area to be rinsed, working down
with same overlapping strokes as you used for
cleaning.
Automatic Cool Down System (Thermal
Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the
spray gun, circulating water in the pump can reach
temperatures above 125°-155°F (51°-68°C). The
system engages to cool the pump by discharging the
warm water onto the ground.
ON (I) Position
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting in
death or serious injury.
• DO NOT use caustic liquid with pressure washer.
• Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
WARNING Kickback from spray gun could
cause you to fall resulting in death or
serious injury.
• Operate pressure washer from a stable surface.
• Be extremely careful if you must use the pressure
washer from a ladder, scaffolding, or any other similar
location.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
15
Not for
Reproduction
Maintenance
Maintenance Schedule
Follow the hourly or calendar intervals, whichever
occurs rst. More frequent service is required when
operating in adverse conditions noted below.
1
Clean if clogged. Replace if perforated or torn.
2
Service more often under dirty or dusty conditions.
General Recommendations
Regular maintenance will improve the performance
and extend the life of the pressure washer. See any
qualied dealer for service.
The pressure washer’s warranty does not cover
items that have been subjected to operator abuse or
negligence. To receive full value from the warranty,
the operator must maintain the pressure washer as
instructed in this manual, including proper storage as
detailed in Winter Storage and Long Term Storage.
NOTICE Should you have questions about replacing
components on your pressure washer, please call
(800) 743-4115 for assistance.
Some adjustments will need to be made periodically to
properly maintain your pressure washer.
All service and adjustments should be made at least
once each season. A new spark plug and clean air lter
assure proper fuel-air mixture and help your engine run
better and last longer. Follow the requirements in the
Maintenance Schedule chart above.
Pump Oil
DO NOT attempt any oil maintenance on this pump.
The pump is pre-lubricated and sealed from the
factory, requiring no additional maintenance for the life
of the pump.
Emissions Control
Maintenance, replacement, or repair of the
emissions control devices and systems may
be performed by any non-road engine repair
establishment or individual. However, to obtain
”no charge” emissions control service, the work must
be performed by a factory authorized dealer. See the
Emissions Warranty.
Before Each Use
1. Check engine oil level.
2. Clean debris.
3. Check water inlet screen for damage.
4. Check high pressure hose for leaks.
5. Check detergent siphoning tube and tank for
damage.
6. Check spray gun and nozzle extension for leaks.
7. Rinse out garden hose to ush out debris.
Fuel Valve Maintenance
The fuel valve is equipped with a fuel sediment cup,
screen, and o-ring that need to be cleaned.
1. Move fuel valve to OFF (0) position.
2. Remove sediment cup (A) from fuel valve.
Remove o-ring (B) and screen (C) from fuel valve.
3. Wash sediment cup, o-ring, and screen in a
nonammable solvent. Dry them thoroughly.
4. Place screen and o-ring into fuel valve. Install
sediment cup and tighten securely.
5. Move fuel valve to ON (I) position, and check for
leaks. Replace fuel valve if there is any leakage.
A
B
C
First 5 Hours
• Change engine oil
Every 8 Hours or Daily
• Check/clean water inlet screen
1
• Check high pressure hose
• Check detergent siphoning tube/tank
• Check spray gun and assembly for leaks
• Clean debris
• Check engine oil level
Every 25 Hours or Yearly
• Service engine air cleaner
2
Every 50 Hours or Yearly
• Change engine oil
2
Every 100 Hours or Yearly
• Service spark plug
• Inspect muer and spark arrester
• Clean cooling system
2
16 BRIGGSandSTRATTON.COM
Not for
Reproduction
Pressure Washer Maintenance
Clean Debris
Daily or before use, clean accumulated debris from
pressure washer. Keep linkage, spring and controls
clean. Keep area around and behind muer free from
any combustible debris. Inspect cooling air slots and
openings on the pressure washer. These openings
must be kept clean and unobstructed.
Pressure washer parts should be kept clean to reduce
the risk of overheating and ignition of accumulated
debris.
• Use a damp cloth to wipe exterior surfaces clean.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
• DO NOT insert any objects through cooling slots.
• Use a soft bristle brush to loosen caked on dirt,
oil, etc.
• Use a vacuum cleaner to pick up loose dirt and
debris.
Check and Clean Inlet Screen
Examine the screen on the pump’s water inlet. Clean
it if the screen is clogged or replace it if screen is
damaged.
Check High Pressure Hose
The high pressure hose can develop leaks from wear,
kinking, or abuse. Inspect the hose each time before
using them. Check for cuts, leaks, abrasions or bulging
of cover, damage or movement of couplings. If any of
these conditions exist, replace the hose immediately.
Check Detergent Siphoning Tube
Examine the detergent tank and detergent siphoning
tube and clean if clogged. The tube should t tightly on
the barbed tting of the pump and detergent shut-o
valve. Examine the tube for leaks or tears. Replace the
tank or tube if either is damaged.
Detergent Siphoning Check Ball
Occasionally check ball in detergent siphoning
system may become stuck from storage, dried soap,
or minerals in water. The check ball can be freed by
performing the following:
NOTICE Before performing this procedure, be sure
you are wearing safety goggles as described below.
1. Shut o engine and turn o water supply.
2. ALWAYS point spray gun in a safe direction,
press red button and squeeze spray gun trigger to
release retained high water pressure.
3. Remove detergent siphoning hose from barbed
tting on pump.
4. Using a rm, blunt object 7/64” in diameter or
smaller, by at least 1” long, such as an Allen
wrench, slowly insert the object into the barbed
tting until you meet resistance. This resistance is
the check ball.
5. Slowly push down until you feel the ball move
slightly, push no more than 1/8”. Slight pressure
may be required to free the ball.
6. Repeat steps 4 and 5 if necessary.
7. Reinstall detergent siphoning hose onto barb
tting.
8. Treat with PumpSaver as described in Protecting
the Pump during storage to prevent reoccurrence.
Check Spray Gun
Examine the hose connection to the spray gun and
make sure it is secure. Test the trigger by pressing the
red button and making sure the trigger “springs back”
into place when you release it. You should not be able
to press the trigger without pressing the red button.
Replace spray gun immediately if it fails any of these
tests.
WARNING
The high pressure stream of water that
this equipment produces could cut through
skin and its underlying tissues, resulting in
serious injury and possible amputation.
• NEVER repair high pressure hose. Replace it.
• Replacement hose rating MUST equal or exceed
maximum pressure rating of unit.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
17
Not for
Reproduction
Spray Tip Maintenance
A pulsing sensation felt while squeezing the spray gun
trigger may be caused by excessive pump pressure.
The principal cause of excessive pump pressure is a
spray tip clogged or restricted with foreign materials,
such as dirt, etc. To correct the problem, immediately
clean the spray tip following these instructions:
1. Shut o engine and turn o water supply.
2. ALWAYS point spray gun in a safe direction,
press red button and squeeze spray gun trigger to
release retained high water pressure.
3. Remove spray tip from end of nozzle extension.
4. Use a small paper clip to free any foreign material
clogging or restricting spray tip (A).
5. Remove nozzle extension from spray gun.
6. Using a garden hose, remove additional debris
by back ushing water through nozzle extension.
Back ush between 30 to 60 seconds.
7. Reinstall spray tip into nozzle extension.
8. Reconnect nozzle extension to spray gun.
9. Make sure garden hose is connected to water
inlet. Check that high pressure hose is connected
to spray gun and pump. Turn on water.
10. Start engine following instructions How to Start
Your Pressure Washer.
11. Test pressure washer by operating with each
quick connect spray tip.
O-Ring Maintenance
Purchase an O-Ring/Maintenance Kit, model 705001,
by contacting the nearest authorized service center.
It is not included with the pressure washer. This kit
includes replacement o-rings, rubber washer and water
inlet lter. Refer to the instruction sheet provided in the
kit to service your unit’s o-rings.
Engine Maintenance
Oil
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty
Certied oils for best performance. Other high-quality
detergent oils are acceptable if classied for service
SF, SG, SH, SJ or higher. DO NOT use special
additives.
Outdoor temperatures determine the proper oil
viscosity for the engine. Use the chart to select the
best viscosity for the outdoor temperature range
expected.
* Below 40°F (4°C) the use of SAE 30 will result in hard
starting.
** Above 80°F (27°C) the use of 10W30 may cause
increased oil consumption. Check oil level more frequently.
A
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
WARNING
The high pressure stream of water that
this equipment produces could cut through
skin and its underlying tissues, resulting in
serious injury and possible amputation.
• NEVER repair leaking connections with sealant of any
kind. Replace o-ring or seal.
WARNING Unintentional sparking could cause
re or electric shock resulting in
death or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
• Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
18 BRIGGSandSTRATTON.COM
Not for
Reproduction
Checking Oil Level
Oil level should be checked prior to each use or
at least every 8 hours of operation. Keep oil level
maintained.
1. Make sure pressure washer is on a level surface.
2. Clean area around oil ll and remove oil ll cap.
3. Verify oil is at the point of overowing at oil ll
opening.
4. Replace and tighten oil ll cap.
Adding Engine Oil
1. Make sure pressure washer is on a level surface.
2. Check oil level as described in Checking Oil
Level.
3. If needed, slowly pour oil into oil ll opening to the
point of overowing at oil ll.
4. Replace and tighten oil ll cap.
Changing Engine Oil
If you are using your pressure washer under extremely
dirty or dusty conditions, or in extremely hot weather,
change the oil more often.
KEEP OUT OF REACH OF CHILDREN.
DON’T POLLUTE. CONSERVE
RESOURCES. RETURN USED OIL TO
COLLECTION CENTERS.
Change oil while engine is still warm from
running, as follows:
1. Make sure unit is on a level surface.
2. Disconnect the spark plug wire from the spark
plug and place the wire where it cannot contact
spark plug.
3. Clean area around oil drain plug (A). The oil
drain plug is located at base of engine, opposite
carburetor.
4. Remove oil drain plug and drain oil completely
into a suitable container.
5. Reinstall oil drain plug and tighten securely.
Remove oil ll cap.
6. Using oil funnel, slowly pour oil (about 20 oz.
(0.6 liters)) into oil ll opening to the point of
overowing at oil ll cap. DO NOT overll.
7. Reinstall oil ll cap. Finger tighten cap securely.
8. Wipe up any spilled oil.
9. Reconnect spark plug wire to spark plug.
Service Air Cleaner
Your engine will not run properly and may be damaged
if you run it with a dirty air cleaner. Replace more often
if operating under dirty or dusty conditions.
To service the air cleaner, follow these steps:
1. Loosen screws (B) and remove air cleaner
cover (C).
2. Carefully remove cartridge (D) from base (E).
3. Install clean (or new) air cleaner assembly inside
cover. Dispose of old lter properly.
4. Assemble air cleaner cover onto base and tighten
screws.
Service Spark Plug
Changing the spark plug will help your engine to start
easier and run better.
1. Clean area around spark plug.
2. Remove and inspect spark plug.
3. Replace spark plug if electrodes are pitted,
burned or porcelain is cracked. Use the
recommended replacement plug. See
Specications.
4. Check electrode gap with wire feeler gauge and
reset spark plug gap to recommended gap if
necessary (see Specications).
5. Install spark plug and tighten rmly.
CAUTION Avoid prolonged or repeated skin
contact with used motor oil.
• Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
• Thoroughly wash exposed areas with soap and water.
B
C
D
E
A
19
Not for
Reproduction
Inspect Muer and Spark Arrester
The engine exhaust muer has a spark arrester
screen. Inspect the muer for cracks, corrosion,
or other damage. Inspect spark arrester screen for
damage or carbon blockage. Clean if carbon blockage
is found or replace if damaged. If replacement parts
are required, make sure to use only original equipment
replacement parts.
Clean or replace spark arrester as follows:
1. Remove four screws that connect heat shield (A)
to muer (B).
2. Remove four screws that attach spark arrester
screen (C).
3. Obtain a replacement screen if torn, perforated
or otherwise damaged. DO NOT use a defective
screen. If screen is not damaged, clean it with
commercial solvent.
4. Reattach screen and muer guard.
Air Cooling System
Over time debris may accumulate in cylinder cooling
ns and cannot be observed without partial engine
disassembly. For this reason, we recommend you have
a qualied service dealer clean the cooling system per
recommended intervals (see Maintenance Schedule in
beginning of Maintenance section). Equally important
is to keep top of engine free from debris. See Clean
Debris.
Carburetor Adjustment
The carburetor on this engine is low emission. It is
equipped with a non-adjustable idle mixture valve.
Top speed has been set at the factory. If adjustment is
required, see an authorized service dealer.
A
B
C
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a re, resulting in
death or serious injury.
Contact with muer area could cause burns
resulting in serious injury.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 ft. (1.5 m) of clearance on all sides of
pressure washer including overhead.
• It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
dened in Section 4442, maintained in eective working
order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.
CAUTION
Excessively high operating speeds
could result in minor injury.
Excessively low speeds impose a heavy load.
• DO NOT tamper with governor spring, links or other
parts to increase engine speed. Pressure washer
supplies correct rated pressure and ow when running at
governed speed.
• DO NOT modify pressure washer in any way.
20 BRIGGSandSTRATTON.COM
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
Simplicity 020541-00 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Simplicity 020541-00 User manual
- español: Simplicity 020541-00 Manual de usuario
Documents connexes
-
Simplicity 020542-00 Manuel utilisateur
-
Briggs & Stratton Elite 3300 MAX PSI Manuel utilisateur
-
-
-
-
-
-
