Briggs & Stratton Elite 3300 MAX PSI Manuel utilisateur

Not for

Reproduction

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

MILWAUKEE, WISCONSIN, U.S.A.

Manual No. 318555 Rev. B

Pressure Washer

Operator’s Manual

This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA)

standard PW101-2010 (Testing and Rating Performance of Pressure Washers).

Not for

Reproduction

2 BRIGGSandSTRATTON.COM

Thank you for purchasing this quality-built Briggs & Stratton® pressure washer. We are pleased that you’ve

placed your condence in the Briggs & Stratton brand. When operated and maintained according to the

instructions in this manual, your Briggs & Stratton pressure washer will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with pressure

washers and how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this

pressure washer could be used for, it is important that you read and understand these instructions thoroughly

before attempting to start or operate this equipment. Save these original instructions for future reference.

This pressure washer requires nal assembly before use. Refer to the Assembly section of this manual for

instructions on nal assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to nd Briggs & Stratton support and service for your pressure washer. Consult your

Yellow Pages. There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality

service. You can also contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet

at BRIGGSandSTRATTON.COM.

Pressure Washer Engine

Model Number _____________________ Model Number ______________________

Revision __________________________ Type Number _______________________

Serial Number ______________________ Code Number _______________________

Date Purchased ___________________

Table of Contents

Operator Safety....................... 3

Assembly............................ 6

Features and Controls ................ 11

Operation........................... 12

Maintenance ........................ 16

Troubleshooting ..................... 23

Warranty ........................... 24

Product Specications ................ 26

Common Service Parts ............... 26

BRIGGS & STRATTON POWER PRODUCTS is a registered

trademark of Briggs & Stratton Corporation

Milwaukee, WI, USA

Not for

Reproduction

3

Operator Safety

Equipment Description

Read this manual carefully and become

familiar with your pressure washer. Know

its applications, its limitations, and any

hazards involved.

This pressure washer operates at 3,300 PSI

(227.5 BAR) and a ow rate of 3.2 gallons

(12.1 liters) per minute. This high quality residential

system features 10” (25.4 cm) wheels, axial cam pump

with stainless steel pistons, automatic cool down

system, cleaning tank system, quick connect spray

tips, heavy duty 50’ (15.24 m) hose, and more.

Every eort has been made to ensure that information

in this manual is accurate and current. However, we

reserve the right to change, alter, or otherwise improve

the product and this document at any time without prior

notice.

The Emission Control System for this pressure washer

is warranted for standards set by the Environmental

Protection Agency and the California Air Resources

Board.

This spark ignition system complies with the Canadian

standard ICES-002.

Important Safety Information

Safety Symbols and Meanings

The safety alert symbol indicates a potential

personal injury hazard. A signal word (DANGER,

WARNING, or CAUTION) is used with the alert symbol

to designate a degree or level of hazard seriousness.

A safety symbol may be used to represent the type of

hazard. The signal word NOTICE is used to address

practices not related to personal injury.

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not

avoided, could result in minor or moderate injury.

NOTICE address practices not related to personal

injury.

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Slippery Surface

Fall

Kickback

Flying Objects

Fluid Injection

Operator’s Manual

Chemical Burn

Projectile

WARNING Chemical Burn Hazard.

Chemicals could cause burns resulting in

death or serious injury.

• DO NOT use caustic liquid with pressure washer.

• Use ONLY pressure washer safe detergents/soaps.

Follow all manufacturers instructions.

WARNING POISONOUS GAS HAZARD.

Engine exhaust contains carbon monoxide,

a poisonous gas that could kill you in

minutes. You CANNOT smell it, see it, or

taste it. Even if you do not smell exhaust fumes, you

could still be exposed to carbon monoxide gas.

Some chemicals or detergents could be harmful if

inhaled or ingested, resulting in death, serious

injury, nausea, fainting or poisoning.

• Operate this product ONLY outside far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for hours,

even after this product has shut o.

• ALWAYS place this product downwind and point the

engine exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this

product, get to fresh air RIGHT AWAY. See a doctor. You

may have carbon monoxide poisoning.

• Use a respirator or mask whenever there is a chance

that vapors may be inhaled when using chemicals.

• Read all instructions with mask so you are certain the

mask will provide the necessary protection against

inhaling harmful vapors when using chemicals.

Not for

Reproduction

4 BRIGGSandSTRATTON.COM

WARNING The engine exhaust from this

product contains chemicals known to the State of

California to cause cancer, birth defects, or other

reproductive harm.

WARNING This product contains lead and lead

compounds, known to the State of California to

cause birth defects or other reproductive harm.

Wash your hands after handling this product.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage

fuel tank causing a re, resulting in

death or serious injury.

Contact with muer area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (1.5 m) of clearance on all sides of

pressure washer including overhead.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

dened in Section 4442, maintained in eective working

order. Other states or federal jurisdictions may have

similar laws.

Contact the original equipment manufacturer, retailer,

or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

• Replacement parts must be the same and installed in the

same position as the original parts.

WARNING Risk of electrocution.

Contact with power source could cause

electric shock or burn resulting in death or

serious injury.

• NEVER spray near power source.

WARNING Use of pressure washer could

create puddles and slippery

surfaces causing you to fall

resulting in death or serious injury.

Kickback from spray gun could cause you to fall

resulting in death or serious injury.

• Operate pressure washer from a stable surface.

• The cleaning area should have adequate slopes and

drainage to reduce the possibility of a fall due to slippery

surfaces.

• Be extremely careful if you must use the pressure

washer from a ladder, scaolding, or any other similar

location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks

back.

WARNING Starter cord kickback (rapid

retraction) will pull hand and arm toward

engine faster than you can let go which

could cause broken bones, fractures,

bruises, or sprains resulting in serious injury.

• NEVER pull starter cord without rst relieving spray gun

pressure.

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run,

always point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks

back.

WARNING Fuel and its vapors are extremely

ammable and explosive which

could cause burns, re or explosion

resulting in death or serious injury.

WHEN ADDING OR DRAINING FUEL

• Turn pressure washer engine OFF and let it cool at least

2 minutes before removing fuel cap. Loosen cap slowly

to relieve pressure in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overll tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting

engine.

• Keep fuel away from sparks, open ames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap and ttings frequently for

cracks or leaks. Replace if necessary.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muer, fuel cap, and air cleaner are in

place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT operate this product inside any building,

carport, porch, mobile equipment, marine applications,

or enclosure.

• DO NOT tip engine or equipment at angle which causes

fuel to spill.

• DO NOT spray ammable liquids.

WHEN TRANSPORTING, MOVING OR REPAIRING

EQUIPMENT

• Transport/move/repair with fuel tank EMPTY or with fuel

shuto valve OFF (0).

• DO NOT tip engine or equipment at angle which causes

fuel to spill.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN

TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other

ignition source because they could ignite fuel vapors.

Not for

Reproduction

5

NOTICE High pressure spray could damage fragile

items including glass.

• DO NOT point spray gun at glass when using red (0°)

spray tip.

• NEVER aim spray gun at plants.

NOTICE Improper treatment of pressure washer

could damage it and shorten its life.

• If you have questions about intended use, ask dealer or

contact qualied service center.

• NEVER operate units with broken or missing parts, or

without protective housing or covers.

• DO NOT by-pass any safety device on this machine.

• DO NOT tamper with governed speed.

• DO NOT operate pressure washer above rated pressure.

• DO NOT modify pressure washer in any way.

• Before starting pressure washer in cold weather, check all

parts of the equipment to be sure ice has not formed there.

• NEVER move machine by pulling on hoses. Use handle

provided on unit.

• This equipment is designed to be used with Briggs &

Stratton Power Products authorized parts ONLY. If

equipment is used with parts that DO NOT comply with

minimum specications, user assumes all risks and

liabilities.

WARNING The high pressure stream of water

that this equipment produces could cut

through skin and its underlying tissues,

resulting in serious injury and possible

amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected, which

could result in serious injury.

• If cut by uid, call physician immediately. DO NOT treat

as a simple cut.

• DO NOT allow CHILDREN to operate pressure washer.

• NEVER repair high pressure hose. Replace it.

• NEVER repair leaking connections with sealant of any

kind. Replace o-ring or seal.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray

gun while system is pressurized.

• ALWAYS point spray gun in safe direction, press red

button and squeeze spray gun trigger to release high

pressure, every time you stop engine.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is

running.

• NEVER use a spray gun which does not have a trigger

lock or trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories

are correctly attached.

WARNING Unintentional sparking could cause

re or electric shock resulting in

death or serious injury.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING Starter and other rotating parts

could entangle hands, hair, clothing, or

accessories resulting in serious injury.

• NEVER operate pressure washer without protective

housing or covers.

• DO NOT wear loose clothing, jewelry or anything that

could be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

CAUTION

Excessively high operating speeds

could result in minor injury.

Excessively low speeds impose a heavy load.

• DO NOT tamper with governor spring, links or other

parts to increase engine speed. Pressure washer

supplies correct rated pressure and ow when running at

governed speed.

• DO NOT modify pressure washer in any way.

WARNING Risk of eye or bodily injury.

Spray could splash back or propel

objects resulting in serious injury.

• Always wear indirect vented (chemical splash) safety

goggles marked to comply with ANSI Z87.1 when using

or in vicinity of this equipment.

• NEVER substitute safety glasses or dry-condition

goggles for indirect vented safety goggles.

• Always wear protective clothing such as a long-sleeved

shirt, long pants and close-toed shoes.

• NEVER operate pressure washer when barefoot or

wearing sandals or shorts.

Not for

Reproduction

6 BRIGGSandSTRATTON.COM

Assembly

Read entire operator’s manual before you

attempt to assemble or operate your new

pressure washer.

Your pressure washer requires some assembly and is

ready for use after it has been properly serviced with

the recommended oil and fuel.

If you have any problems with the assembly of your

pressure washer, please call the pressure washer

helpline at (800) 743-4115. If calling for assistance,

please have the model, revision, and serial number from

the identication label available.

Unpack Pressure Washer

1. Remove the parts bag, accessories, and inserts

included with pressure washer.

2. Open carton completely by cutting each corner

from top to bottom.

3. Ensure you have all included items prior to

assembly.

Items in the carton include:

• Main Unit

• High Pressure Hose

• Spray Gun

• Nozzle Extension with Quick Connect Fitting

• Hose Wrap

• Wheels (2)

• Caster Wheels (2)

• Oil Bottle

• Oil Funnel

• Spray Gun Holder Wireform

• Battery Float Charger

• Operator’s Manual

• Owner’s Registration Card

• Multi–Colored Spray Tips (5)

• Handle Pin

• Axle Studs (2)

• Retaining Pins (2)

• Washers (4)

• Keys (2)

• Metal Spring Clips (2)

• Plastic Knobs (1)

• Screws (5)

• Hex Key Wrench

To prepare your pressure washer for operation,

you will need to perform these tasks:

1. Fill out and send in registration card.

2. Attach hose wrap, metal spring clips, spray gun

holder wireform and handle pin to main unit.

3. Install wheel kit on main unit.

4. Add oil to engine crankcase.

5. Add fuel to fuel tank.

6. Connect high pressure hose to spray gun and

pump.

7. Connect water supply to pump.

8. Attach nozzle extension to spray gun.

9. Select/attach quick connect spray tip to nozzle

extension.

Attach Accessory Holders

All assembly instructions in this section will be viewing

from engine end of unit.

1. Place hose wrap (A) over holes (B) on end of

main unit. Using provided hex key wrench, attach

hose wrap with three screws (C). Tighten by hand.

2. Insert spray gun holder wireform (D) through holes

on right side of unit frame. Hold wireform in place

and attach a plastic knob (E) from inside of unit.

Tighten by hand.

3. Using provided hex key wrench, attach metal

spring clips (F) to left side frame of unit with

screws (G). Tighten by hand.

E

D

C

A

B

G

F

Not for

Reproduction

7

Install Wheel Kit

NOTICE Wheel kit is not intended for over-the-road use.

Install the wheel kit as follows:

1. Lift corner of pressure washer and slide caster

wheels up into bottom of tubing on each

underside of pressure washer frame.

2. Using a 3/4” (19 mm) wrench, turn nut (A) under

collar of caster wheels to tighten.

3. Slide at washer (B), wheel (C) and another at

washer (B) over axle stud (D).

NOTICE Be sure to install wheel with raised hub inward.

4. Lift corner of pressure washer slightly and slide

axle stud through mounting bracket on pressure

washer frame.

5. Insert retaining pin (E) through hole on axle stud.

6. Repeat steps 3 through 5 to secure second wheel.

Moving Pressure Washer

The pressure washer is equipped with a handle

that locks into three dierent positions for your

convenience. With the handle in the upright position,

it makes it easy to push or pull your pressure washer

to the desired location. With the handle in the middle

position, you can tilt the pressure washer back. The

handle also folds down at for storage.

1. Screw handle pin (F) into bracket on left side of

frame (viewing pressure washer from engine end).

2. Pull handle pin out and lift handle to desired

position.

3. Release handle pin and make sure latch (G) locks

into place.

4. Place lock levers on caster wheels in the OFF (0)

postion to unlock wheels and move pressure washer

to desired location.

NOTICE Always face pressure washer and push or

pull to desired location. When moving pressure washer

on an incline, always make sure you are uphill from

pressure washer.

5. Place lock levers on caster wheels in the ON (I)

postion to lock wheels and keep pressure washer

from moving.

Attach Negative Battery Cable

Your unit is equipped with electric start capability but

can be started manually. If you choose not to use the

electric start feature, you do not need to connect the

negative battery cable.

The sealed battery on the pressure washer is pre–

installed except for the negative (black) battery cable.

To install:

1. Cut o tie wrap securing loose end of negative

(black) cable.

2. Using 8 mm wrenches, remove screw (H) and nut

(J) on negative battery terminal (—) (K).

3. Slide negative battery cable (L) over screw.

F

G

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds -

chemicals known to the State of California to cause

cancer and reproductive harm. Wash hands after

handling.

H

L

J

K

B

E

C

D

A

Not for

Reproduction

8 BRIGGSandSTRATTON.COM

4. Reattach screw and nut on negative terminal and

tighten.

5. Verify that connections to battery and pressure

washer are tight and secure.

NOTICE If your battery is discharged, charge prior

to use following the instructions in the section Battery

Charger.

Add Engine Oil

1. Place pressure washer on a at, level surface.

2. Clean area around oil ll and remove yellow oil ll

cap.

3. Using oil funnel, slowly pour contents of

provided oil into oil ll opening (A) to the point of

overowing at oil ll cap. DO NOT overll.

NOTICE Improper treatment of pressure washer

could damage it and shorten its life.

• DO NOT attempt to crank or start the engine before it has

been properly serviced with the recommended oil. This

may result in an engine failure.

4. Replace oil ll cap and fully tighten.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). For

high altitude use, see High Altitude.

• Gasoline with up to 10% ethanol (gasohol) is

acceptable.

NOTICE Use of unapproved fuels could damage

pressure washer and voids warranty.

• DO NOT use unapproved gasoline such as E15 and E85.

• DO NOT mix oil in gasoline or modify engine to run on

alternate fuels.

To protect the fuel system from gum formation, mix in a

fuel stabilizer when adding fuel. See Storage. All fuel is

not the same. If you experience starting or performance

problems after using fuel, switch to a dierent fuel

provider or change brands. This engine is certied to

operate on gasoline. The emission control system for this

engine is EM (Engine Modications).

1. Clean area around fuel ll cap, remove cap.

2. Slowly add unleaded gasoline (B) to fuel tank

(C). Be careful not to ll above the bae (D).

This allows adequate space for fuel expansion as

shown.

3. Install fuel cap and let any spilled fuel evaporate

before starting engine.

High Altitude

At altitudes over 5,000 ft. (1,524 m), a minimum

85 octane / 85 AKI (89 RON) gasoline is acceptable.

To remain emissions compliant, high altitude

adjustment is required. Operation without this

adjustment will cause decreased performance,

increased fuel consumption, and increased emissions.

See an Authorized Briggs & Stratton dealer for high

altitude adjustment information. Operation of the

engine at altitudes below 2,500 ft. (762 m) with the

high altitude kit is not recommended.

FUEL

TANK

D

C

B

A

WARNING Fuel and its vapors are extremely

ammable and explosive which could

cause burns, re or explosion

resulting in death or serious injury.

WHEN ADDING FUEL

• Turn pressure washer engine OFF and let it cool at least

2 minutes before removing fuel cap. Loosen cap slowly

to relieve pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overll tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting

engine.

• Keep fuel away from sparks, open ames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap and ttings frequently for

cracks or leaks. Replace if necessary.

• DO NOT light a cigarette or smoke.

Not for

Reproduction

9

Lubricate O-Rings

Lubrication of o-rings is extremely important for

installation and operation. The use of a lubricant

(petroleum or synthetic grease) during assembly helps

seat o-rings properly and provides an improved seal. It

also helps protect the o-ring from damage by abrasion,

pinching or cutting and extends the life of the o-ring.

NOTICE ALWAYS apply a small amount of lubricant

on o-rings prior to assembling the garden hose to the

pump inlet (A), high pressure hose to pump outlet (B),

high pressure hose (C), nozzle extension (D), and

spray gun (E).

Lubricate all connections shown below, following

these instructions:

1. Inspect and clean connecting surfaces prior to

lubrication and assembly.

2. Use lubricants sparingly during assembly; a light

lm is all that is required.

3. Use a small brush or cotton swab to apply grease

directly to o-rings where they are not accessible

(QC tting, M22 tting).

Battery Charger

Use battery oat charger jack to keep the starting

battery charged and ready for use. Battery charging

should be done in a dry location, such as inside a

garage.

1. Plug charger into unit’s “Battery Float Charger”

jack, which is located next to the start switch. Plug

battery charger into a 120 Volt AC wall receptacle.

2. Unplug charger from unit and wall outlet when

pressure washer is being started and while it is in

operation.

3. Keep this charger plugged in when pressure

washer is not in use to prolong battery life. The

charger has a built in oat equalizer and will not

overcharge the battery, even when plugged in for

an extended period of time.

NOTICE See Battery Maintenance for additional

information.

B

E

C

A

D

Not for

Reproduction

10 BRIGGSandSTRATTON.COM

Connect Hose and Water Supply to Pump

NOTICE DO NOT run the pump without the water

supply connected and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

NOTICE Remove and discard the shipping caps from

the pump’s high pressure outlet and water inlet before

attaching hoses.

1. Uncoil high pressure hose and attach quick

connect end of hose to base of spray gun. Pull

down on collar of quick connect, slide onto spray

gun and let go of collar. Tug on hose to be sure of

tight connection.

2. Similarly, attach other end of high pressure hose

to high pressure outlet (A) on pump. Pull down

on collar of quick connect, slide onto pump and

let go of collar. Pull on hose to be sure of tight

connection.

3. Before connecting garden hose to water inlet,

inspect inlet screen (B). Clean screen if it contains

debris or have it replaced if damaged. DO NOT

run pressure washer if inlet screen is damaged.

4. Run water through your garden hose for

30 seconds to clean out any debris.

NOTICE DO NOT siphon standing water for the water

supply. Use ONLY cold water (less than 100°F (38°C)).

NOTICE Using a One Way Valve (vacuum breaker

or check valve) at pump inlet could cause pump or

inlet connector damage.

• There MUST be at least 10 ft. (3 m) of unrestricted garden

hose between the pressure washer inlet and any device,

such as a vacuum breaker or check valve.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

5. Connect the garden hose (not to exceed 50 ft.

(15 m) in length) to the water inlet. Tighten by

hand.

6. Turn ON the water, press red button (C) on the

gun and squeeze the trigger to purge the pump

system of air and impurities.

Checklist Before Starting Engine

Review the unit’s assembly to ensure you have

performed all of the following.

1. Be sure to read Operator Safety and Operation

sections before using pressure washer.

2. Make sure handle is in place and secure.

3. Check that oil has been added to proper level in

the engine crankcase.

4. Add proper fuel to fuel tank.

5. Check for properly tightened hose connections.

6. Check to make sure there are no kinks, cuts, or

damage to high pressure hose.

7. Provide a proper water supply at an adequate

ow.

B

C

A

WARNING The high pressure stream of water

that this equipment produces could cut

through skin and its underlying tissues,

resulting in serious injury and possible

amputation.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray

gun while system is pressurized.

• Always be certain spray gun, nozzles and accessories

are correctly attached.

WARNING Risk of eye injury.

Spray could splash back or propel objects

resulting in serious injury.

• Always wear indirect vented (chemical splash) safety

goggles marked to comply with ANSI Z87.1 when using

or in vicinity of this equipment.

• NEVER substitute safety glasses or dry-condition

goggles for indirect vented safety goggles.

Not for

Reproduction

11

Features and Controls

Read this Operator’s Manual and safety rules before operating your pressure washer.

Compare the illustrations with your pressure washer, to familiarize yourself with the locations of various

controls and adjustments. Save this manual for future reference.

A - Spray Gun — Controls the application of water

onto cleaning surface with trigger device. Includes

trigger lock.

B - High Pressure Hose — Connect one end to water

pump and the other end to spray gun.

C - Nozzle Extension with Quick Connect — Allows

you to switch between ve dierent spray tips.

D - Spark Arrester Muer — Exhaust muer lowers

engine noise and is equipped with a spark arrester

screen.

E - Water Inlet — Connection for garden hose.

F - Pressure Control Knob — Varies pressure of high

pressure spray.

G - Pump — Develops high pressure.

H - Automatic Cool Down System — Cycles water

through pump when water reaches 125°-155°F

(51°-68°C). Warm water will discharge from pump

onto ground. This system prevents internal pump

damage.

J - Air Filter — Protects engine by ltering dust and

debris out of intake air.

K - Recoil Starter — Used for starting the engine

manually.

L - High Pressure Outlet — Connection for high

pressure hose.

M - Throttle Lever — Sets engine in starting mode

for electric or manual starting and stops a running

engine.

N - Quick Connect Spray Tips — Detergent, 0°, 15°,

25° and 40°: for various high pressure cleaning

applications.

P - Battery Float Charger Jack — Use battery oat

charger jack to keep the starting battery charged

and ready for use.

R - Start Switch — Turn key to start (

) position to

start the engine.

S - Fuel Valve — Used to turn fuel supply on and o

to engine.

T - Choke Lever — Prepares a cold engine for starting.

U - Fuel Tank — Fill tank with regular unleaded fuel.

Always leave room for fuel expansion.

V - Cleaning Tanks – Use to hold up to 1 gallon

(3.8 liters) of pressure washer safe detergent in

each tank.

Items Not Shown:

Identication Label — Provides model and serial

number of pressure washer. Please have these readily

available if calling for assistance.

Oil Drain — Drain engine oil here.

Oil Fill — Check and add engine oil here.

A

D

B

K

M

R

L

F

J

V

E

U

C

T

P

H

,

G

S

N

Not for

Reproduction

12 BRIGGSandSTRATTON.COM

Operation

If you have any problems operating your pressure

washer, please call the pressure washer helpline at

(800) 743-4115.

Pressure Washer Location

Carbon Monoxide Poisoning

Risk of Fire Clearances

How to Start Your Pressure Washer

To start your pressure washer for the rst time,

follow these instructions step-by-step. This starting

information also applies if you have let the pressure

washer sit idle for at least a day.

1. Place pressure washer near an outside water

source capable of supplying water at a ow rate

greater than 4.2 gallons (16 liters) per minute and

no less than 20 PSI (1.4 BAR) at pressure washer

end of garden hose. DO NOT siphon supply water.

2. Check that high pressure hose is tightly connected

to spray gun and pump. See Assembly section.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure

washer pump.

NOTICE DO NOT run the pump without the water

supply connected and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

5. Turn ON water, point gun in a safe direction, press

red button and squeeze trigger to purge pump

system of air and impurities.

6. Attach nozzle extension to spray gun. Tighten by

hand.

7. Choose spray tip you want to use, pull back on

collar of nozzle extension, insert spray tip and

release collar. Tug on spray tip to make sure it is

securely in place. See How to Use Spray Tips.

8. Turn fuel valve (A) to ON (I) position. The fuel

valve handle should be vertical (pointing toward

the ground) for fuel to ow.

9. Move throttle control lever (B) to FAST ( )

position, shown on engine as a rabbit.

A

Exhaust Port

Pointed away

from occupied

spaces

B

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel tank

causing a re, resulting in death or serious

injury.

• Keep at least 5 ft. (1.5 m) clearance on all sides of

pressure washer including overhead.

WARNING POISONOUS GAS HAZARD.

Engine exhaust contains carbon monoxide,

a poisonous gas that could kill you in

minutes. You CANNOT smell it, see it, or

taste it. Even if you do not smell exhaust fumes, you

could still be exposed to carbon monoxide gas.

• Operate this product ONLY outside far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for hours,

even after this product has shut o.

• ALWAYS place this product downwind and point the

engine exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this

product, get to fresh air RIGHT AWAY. See a doctor. You

may have carbon monoxide poisoning.

Not for

Reproduction

13

10. Move choke lever (A) to CHOKE ( ) position.

NOTICE For a warm engine, be sure the choke lever

is in the RUN ( ) position.

NOTICE Before starting the pressure washer, be sure

you are wearing safety goggles as described below.

11A. For electric starting, turn and hold key in start

switch to start ( ) position until pressure washer

starts. To prolong the life of starter components,

DO NOT hold key in start ( ) position for more

than 5 seconds, and pause for at least 1 minute

between starting attempts.

• If engine starts, proceed to step 14.

• If engine fails to start, proceed to step 12.

NOTICE If battery is discharged, use manual starting

instructions.

11B. For manual starting, position yourself as

recommended below, grasp recoil handle and pull

slowly until you feel some resistance. Then pull

rapidly to start engine. Return starter grip handle

slowly. DO NOT let rope “snap back” against starter.

• If engine starts, proceed to step 14.

• If engine fails to start, proceed to step 12.

NOTICE After each starting attempt, where engine

fails to run, always point gun in safe direction, press

red button and squeeze spray gun trigger to release

high pressure.

12. Move choke lever half way, pull recoil handle

twice or turn and hold key in start switch to

start (

) position as described in step 11A.

• If engine fails to start, repeat steps 10 thru 11.

13. If engine fails to start after six pulls, move choke

lever to RUN ( ) position, and repeat step 11.

14. When engine starts, slowly move choke lever to

RUN ( ) position, as engine warms. If engine

falters, move choke lever to CHOKE ( )

position, then to RUN ( ) position.

NOTICE Always keep the throttle control lever in the

FAST ( ) position when operating the pressure

washer.

A

WARNING Risk of eye injury.

Spray could splash back or propel objects

resulting in serious injury.

• Always wear indirect vented (chemical splash) safety

goggles marked to comply with ANSI Z87.1 when using

or in vicinity of this equipment.

• NEVER substitute safety glasses or dry-condition

goggles for indirect vented safety goggles.

WARNING Starter cord kickback (rapid

retraction) will pull hand and arm toward

engine faster than you can let go which

could cause broken bones, fractures,

bruises, or sprains resulting in serious injury.

• NEVER pull starter cord without rst relieving spray gun

pressure.

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run,

always point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING The high pressure stream of water

that this equipment produces could cut

through skin and its underlying tissues,

resulting in serious injury and possible

amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected, which

could result in serious injury.

• DO NOT allow CHILDREN to operate pressure washer.

• Keep high pressure hose connected to pump and spray

gun while system is pressurized.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is

running.

• NEVER use a spray gun which does not have a trigger

lock or trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories

are correctly attached.

Not for

Reproduction

14 BRIGGSandSTRATTON.COM

How to Stop Your Pressure Washer

1. Release spray gun trigger and let engine idle for

two minutes.

2. Move throttle to SLOW ( ) position, then

STOP ( ) position.

3. Turn fuel valve to OFF (0) position.

How to Store Accessories

The unit is equipped with multiple places to store your

spray gun, nozzle extension, high pressure hose and

spray tips.

1. Place spray gun into spray gun holder wireform as

shown.

2. Place nozzle extension into metal spring clips on

side of unit as shown.

3. Coil high pressure hose onto hose wrap.

4. Insert multi–colored spray tips in spaces provided

on side panel.

How to Use Spray Tips

The quick–connect on the nozzle extension allows you

to switch between ve dierent quick connect spray

tips. Spray tips can be changed while pressure washer

is running once spray gun trigger lock is engaged. The

spray tips vary the spray pattern as shown.

Follow these instructions to change spray tips:

1. Pull back collar on quick–connect and pull current

spray tip o. Store spray tips in holder provided on

the side panel.

2. Select desired spray tip:

• For gentle rinse, select white 40° or green 25°

spray tip.

• To scour surface, select yellow 15° or red 0° spray tip.

• To apply detergent, select black spray tip.

White 40° Green 25°Black Yellow 15° Red 0°

Low

Pressure

Use to apply

detergent

High

Pressure

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage

fuel tank causing a re, resulting in

death or serious injury.

Contact with muer area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (1.5 m) of clearance on all sides of

pressure washer including overhead.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

dened in Section 4442, maintained in eective working

order. Other states or federal jurisdictions may have

similar laws.

Contact the original equipment manufacturer, retailer,

or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

• Replacement parts must be the same and installed in the

same position as the original parts.

WARNING The high pressure stream of water

that this equipment produces could cut

through skin and its underlying tissues,

resulting in serious injury and possible

amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected, which

could result in serious injury.

• Keep high pressure hose connected to pump and spray

gun while system is pressurized.

• ALWAYS point spray gun in safe direction, press red

button and squeeze spray gun trigger to release high

pressure, every time you stop engine.

WARNING The high pressure stream of water

that this equipment produces could cut

through skin and its underlying tissues,

resulting in serious injury and possible

amputation.

• NEVER exchange spray tips without the trigger lock

being engaged on the spray gun.

• DO NOT twist spray tips while spraying.

Not for

Reproduction

15

3. Pull back on collar, insert new spray tip and

release collar. Tug on spray tip to make sure it is

securely in place.

Usage Tips

• For most eective cleaning, keep spray tip from

8 to 24 inches (20 to 61 cm) away from cleaning

surface.

• If you get spray tip too close, especially using a

high pressure spray tip, you may damage surface

being cleaned.

• DO NOT get closer than 6 inches (15 cm) when

cleaning tires.

Applying Detergent

To apply detergent, follow these steps:

1. Review use of spray tips.

2. Prepare detergent solution as required by job.

3. Make sure detergent shut-o valves on cleaning

tanks are in OFF (0) position.

4. Pour detergent solution into one of the cleaning tanks.

NOTICE Each cleaning tank holds up to 1 gallon

(3.8 liters).

5. Fill other cleaning tank with a dierent prepared

solution, as desired.

6. Make sure black detergent spray tip is installed.

NOTICE Detergent cannot be applied with the high

pressure spray tips (White, Green, Yellow or Red).

7. Make sure garden hose is connected to water

inlet. Check that high pressure hose is connected

to spray gun and pump. Turn on water.

NOTICE You must attach all hoses before you start

engine.

• Starting the engine without all the hoses connected and

without the water turned ON could damage the pump.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

8. Start engine following instructions How to Start

Your Pressure Washer.

9. Rotate detergent shut-o valve on desired

cleaning tank to ON (I) position.

10. Apply detergent to a dry surface, starting at lower

portion of area to be washed and work upward,

using long, even, overlapping strokes.

11. Allow detergent to “soak in” for 3-5 minutes

before washing and rinsing. Reapply as needed

to prevent surface from drying. DO NOT allow

detergent to dry on (prevents streaking).

Pressure Washer Rinsing

For Rinsing:

1. Turn detergent shut-o valves to OFF (0) position.

2. Remove black detergent spray tip from nozzle

extension.

3. Select and install desired high pressure spray tip

following instructions How to Use Spray Tips.

4. Keep the spray gun a safe distance from the area

you plan to spray.

5. Increase (decrease) spray pressure by turning

pressure control knob (A) counterclockwise

(clockwise). Use lower pressure to wash items

such as a car or boat. Use higher pressure to strip

paint and degrease driveways.

6. Apply a high pressure spray to a small area and

then check surface for damage. If no damage

is found, you can assume it is okay to continue

rinsing.

7. Start at top of area to be rinsed, working down

with same overlapping strokes as you used for

cleaning.

Automatic Cool Down System (Thermal

Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the

spray gun, circulating water in the pump can reach

temperatures above 125°-155°F (51°-68°C). The

system engages to cool the pump by discharging the

warm water onto the ground.

ON (I)

Position

OFF (0)

Position

CAUTION Mixing detergents could result in

bodily injury.

• DO NOT open both detergent shut-o valves at same

time.

A

WARNING Chemical Burn Hazard.

Chemicals could cause burns resulting in

death or serious injury.

• DO NOT use caustic liquid with pressure washer.

• Use ONLY pressure washer safe detergents/soaps.

Follow all manufacturers instructions.

WARNING Kickback from spray gun could

cause you to fall resulting in death or

serious injury.

• Operate pressure washer from a stable surface.

• Be extremely careful if you must use the pressure washer

from a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

Not for

Reproduction

16 BRIGGSandSTRATTON.COM

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever

occurs rst. More frequent service is required when

operating in adverse conditions noted below.

1

Clean if clogged. Replace if perforated or torn.

2

Service more often under dirty or dusty conditions.

3

Change pump oil after the rst (50) operating hours and then every

200 hours or 3 months thereafter.

General Recommendations

Regular maintenance will improve the performance

and extend the life of the pressure washer. See any

qualied dealer for service.

The pressure washer’s warranty does not cover

items that have been subjected to operator abuse or

negligence. To receive full value from the warranty,

the operator must maintain the pressure washer as

instructed in this manual, including proper storage as

detailed in Winter Storage and Long Term Storage.

NOTICE Should you have questions about replacing

components on your pressure washer, please call

(800) 743-4115 for assistance.

Some adjustments will need to be made periodically to

properly maintain your pressure washer.

All service and adjustments should be made at least

once each season. A new spark plug and clean

air lter assure proper fuel-air mixture and help

your engine run better and last longer. Follow the

requirements in the Maintenance Schedule chart.

Emissions Control

Maintenance, replacement, or repair of the

emissions control devices and systems may

be performed by any non-road engine repair

establishment or individual. However, to obtain

”no charge” emissions control service, the work must

be performed by a factory authorized dealer. See the

Emissions Warranty.

Before Each Use

1. Check engine oil level.

2. Clean debris.

3. Check water inlet screen for damage.

4. Check high pressure hose for leaks.

5. Check detergent siphoning tubes and tank for

damage.

6. Check spray gun and nozzle extension for leaks.

7. Rinse out garden hose to ush out debris.

Battery Maintenance

Other than oat charging, described elsewhere, no

maintenance is required for the starting battery. Keep

the battery and terminals clean and dry.

NOTICE Battery charging should be performed in a

dry location, such as inside a garage.

Fuel Valve Maintenance

The fuel valve is equipped with a fuel sediment cup,

screen, and o-ring that need to be cleaned.

1. Move fuel valve to OFF (0) position.

2. Remove sediment cup (A) from fuel valve.

Remove o-ring (B) and screen (C) from fuel valve.

3. Wash sediment cup, o-ring, and screen in a

nonammable solvent. Dry them thoroughly.

4. Place screen and o-ring into fuel valve. Install

sediment cup and tighten securely.

5. Move fuel valve to ON (I) position, and check for

leaks. Replace fuel valve if there is any leakage.

A

B

C

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds -

chemicals known to the State of California to cause

cancer and reproductive harm. Wash hands after

handling.

First 5 Hours

• Change engine oil

Every 8 Hours or Daily

• Check/clean water inlet screen

1

• Check high pressure hose

• Check detergent siphoning tube/tank

• Check spray gun and assembly for leaks

• Clean debris

• Check engine oil level

Every 25 Hours or Yearly

• Service engine air cleaner

2

Every 50 Hours or Yearly

• Change engine oil

2

Every 100 Hours or Yearly

• Service spark plug

• Inspect muer and spark arrester

• Clean cooling system

2

Every 200 Hours or 3 Months

• Change pump oil

3

Not for

Reproduction

17

Pressure Washer Maintenance

Clean Debris

Daily or before use, clean accumulated debris from

pressure washer. Keep linkage, spring and controls

clean. Keep area around and behind muer free from

any combustible debris. Inspect cooling air slots and

openings on the pressure washer. These openings

must be kept clean and unobstructed.

Pressure washer parts should be kept clean to reduce

the risk of overheating and ignition of accumulated

debris.

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE Improper treatment of pressure washer

could damage it and shorten its life.

• DO NOT insert any objects through cooling slots.

• Use a soft bristle brush to loosen caked on dirt,

oil, etc.

• Use a vacuum cleaner to pick up loose dirt and

debris.

Check and Clean Inlet Screen

Examine the screen on the pump’s water inlet. Clean

it if the screen is clogged or replace it if screen is

damaged.

Check High Pressure Hose

The high pressure hose can develop leaks from wear,

kinking, or abuse. Inspect the hose each time before

using them. Check for cuts, leaks, abrasions or bulging

of cover, damage or movement of couplings. If any of

these conditions exist, replace the hose immediately.

Check Detergent Siphoning Tube

Examine the detergent tanks and detergent siphoning

tubes and clean if clogged. The tubes should t

tightly on the barbed tting of the pump and detergent

shut-o valves. Examine the tubes for leaks or tears.

Replace the tanks or tubes if either is damaged.

Detergent Siphoning Check Ball

Occasionally check ball in detergent siphoning

system may become stuck from storage, dried soap,

or minerals in water. The check ball can be freed by

performing the following:

NOTICE Before performing this procedure, be sure

you are wearing safety goggles as described below.

1. Shut o engine and turn o water supply.

2. ALWAYS point spray gun in a safe direction,

press red button and squeeze spray gun trigger to

release retained high water pressure.

3. Remove detergent siphoning hose from barbed

tting on pump.

4. Using a rm, blunt object 7/64” in diameter or

smaller, by at least 1” long, such as an Allen

wrench, slowly insert the object into the barbed

tting until you meet resistance. This resistance is

the check ball.

5. Slowly push down until you feel the ball move

slightly, push no more than 1/8”. Slight pressure

may be required to free the ball.

6. Repeat steps 4 and 5 if necessary.

7. Reinstall detergent siphoning hose onto barb

tting.

8. Treat with PumpSaver as described in Protecting

the Pump during storage to prevent reoccurrence.

Check Spray Gun

Examine the hose connection to the spray gun and

make sure it is secure. Test the trigger by pressing the

red button and making sure the trigger “springs back”

into place when you release it. You should not be able

to press the trigger without pressing the red button.

Replace spray gun immediately if it fails any of these

tests.

WARNING

The high pressure stream of water that

this equipment produces could cut through

skin and its underlying tissues, resulting in

serious injury and possible amputation.

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST equal or exceed

maximum pressure rating of unit.

WARNING The high pressure stream of water

that this equipment produces could cut

through skin and its underlying tissues,

resulting in serious injury and possible

amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected, which

could result in serious injury.

• Keep high pressure hose connected to pump and spray

gun while system is pressurized.

• ALWAYS point spray gun in safe direction, press red

button and squeeze spray gun trigger to release high

pressure, every time you stop engine.

WARNING Risk of eye injury.

Spray could splash back or propel objects

resulting in serious injury.

• Always wear indirect vented (chemical splash) safety

goggles marked to comply with ANSI Z87.1 when using

or in vicinity of this equipment.

• NEVER substitute safety glasses or dry-condition

goggles for indirect vented safety goggles.

Not for

Reproduction

18 BRIGGSandSTRATTON.COM

Spray Tip Maintenance

A pulsing sensation felt while squeezing the spray gun

trigger may be caused by excessive pump pressure.

The principal cause of excessive pump pressure is a

spray tip clogged or restricted with foreign materials,

such as dirt, etc. To correct the problem, immediately

clean the spray tip following these instructions:

1. Shut o engine and turn o water supply.

2. ALWAYS point spray gun in a safe direction,

press red button and squeeze spray gun trigger to

release retained high water pressure.

3. Remove spray tip from end of nozzle extension.

4. Use a small paper clip to free any foreign material

clogging or restricting spray tip (A).

5. Remove nozzle extension from spray gun.

6. Using a garden hose, remove additional debris

by back ushing water through nozzle extension.

Back ush between 30 to 60 seconds.

7. Reinstall spray tip into nozzle extension.

8. Reconnect nozzle extension to spray gun.

9. Make sure garden hose is connected to water

inlet. Check that high pressure hose is connected

to spray gun and pump. Turn on water.

10. Start engine following instructions How to Start

Your Pressure Washer.

11. Test pressure washer by operating with each

quick connect spray tip.

O-Ring Maintenance

Purchase an O-Ring/Maintenance Kit, model 705001,

by contacting the nearest authorized service center.

It is not included with the pressure washer. This kit

includes replacement o-rings, rubber washer and water

inlet lter. Refer to the instruction sheet provided in the

kit to service your unit’s o-rings.

Pump Oil Maintenance

Changing Pump Oil

NOTICE When changing pump oil, use only high

quality SAE 30 weight oil. Use no special additives.

Change pump oil as follows:

1. Clean area around brass oil drain plug at bottom

of pump.

2. Remove oil drain plug. Drain oil completely into an

approved container.

3. When oil has completely drained, install oil drain

plug and tighten rmly.

4. Clean area around pump oil dipstick. Remove

dipstick and ll pump with recommended oil

(approximately 12 oz. (0.35 liters)) to FULL mark

on dipstick.

5. Install pump oil dipstick.

6. Wipe up any spilled oil.

Engine Maintenance

Oil

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certied oils for best performance. Other high-quality

detergent oils are acceptable if classied for service SF,

SG, SH, SJ or higher. DO NOT use special additives.

Outdoor temperatures determine the proper oil

viscosity for the engine. Use the chart to select the

best viscosity for the outdoor temperature range

expected.

A

WARNING The high pressure stream of water

that this equipment produces could cut

through skin and its underlying tissues,

resulting in serious injury and possible

amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected, which

could result in serious injury.

• Keep high pressure hose connected to pump and spray

gun while system is pressurized.

• ALWAYS point spray gun in safe direction, press red

button and squeeze spray gun trigger to release high

pressure, every time you stop engine.

WARNING The high pressure stream of water that

this equipment produces could cut through

skin and its underlying tissues, resulting in

serious injury and possible amputation.

• NEVER repair leaking connections with sealant of any

kind. Replace o-ring or seal.

WARNING Unintentional sparking could cause

re or electric shock resulting in

death or serious injury.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Not for

Reproduction

19

* Below 40°F (4°C) the use of SAE 30 will result in hard

starting.

** Above 80°F (27°C) the use of 10W30 may cause

increased oil consumption. Check oil level more frequently.

Checking Oil Level

Oil level should be checked prior to each use or

at least every 8 hours of operation. Keep oil level

maintained.

1. Make sure pressure washer is on a level surface.

2. Clean area around oil ll and remove oil ll cap.

3. Verify oil is at the point of overowing at oil ll

opening.

4. Replace and tighten oil ll cap.

Adding Engine Oil

1. Make sure pressure washer is on a level surface.

2. Check oil level as described in Checking Oil

Level.

3. If needed, slowly pour oil into oil ll opening to the

point of overowing at oil ll.

4. Replace and tighten oil ll cap.

Changing Engine Oil

If you are using your pressure washer under extremely

dirty or dusty conditions, or in extremely hot weather,

change the oil more often.

KEEP OUT OF REACH OF CHILDREN.

DON’T POLLUTE. CONSERVE

RESOURCES. RETURN USED OIL TO

COLLECTION CENTERS.

Change engine oil when engine is cold, as follows:

1. Make sure unit is on a level surface.

2. Disconnect the spark plug wire from the spark

plug and place the wire where it cannot contact

spark plug.

3. Clean area around oil drain plug (A). The oil drain

plug is located at base of engine.

4. Remove oil drain plug and drain oil completely

into a suitable container.

5. Reinstall oil drain plug and tighten securely.

Remove oil ll cap.

6. Using oil funnel, slowly pour oil (about 20 oz.

(0.6 liters)) into oil ll opening (B) to the point of

overowing at oil ll cap. DO NOT overll.

7. Reinstall oil ll cap. Finger tighten cap securely.

8. Wipe up any spilled oil.

9. Reconnect spark plug wire to spark plug.

Service Air Cleaner

Your engine will not run properly and may be damaged

if you run it with a dirty air cleaner. Replace more often

if operating under dirty or dusty conditions.

To service the air cleaner, follow these steps:

1. Loosen screws (C) and remove air cleaner

cover (D).

2. Carefully remove cartridge (E) from base (F).

3. Install clean (or new) air cleaner assembly inside

cover. Dispose of old lter properly.

4. Assemble air cleaner cover onto base and tighten

screws.

C

D

E

F

B

A

CAUTION Avoid prolonged or repeated skin

contact with used motor oil.

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Not for

Reproduction

20 BRIGGSandSTRATTON.COM

Service Spark Plug

Changing the spark plug will help your engine to start

easier and run better.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Replace spark plug if electrodes are pitted,

burned or porcelain is cracked. Use the

recommended replacement plug. See

Specications.

4. Check electrode gap with wire feeler gauge and

reset spark plug gap to recommended gap if

necessary (see Specications).

5. Install spark plug and tighten rmly.

Inspect Muer and Spark Arrester

Inspect the muer for cracks, corrosion, or other

damage. Remove the spark arrester, if equipped, and

inspect for damage or carbon blockage. If replacement

parts are required, make sure to use only original

equipment replacement parts.

Clean and inspect the spark arrester as follows:

1. To remove muer heat shield (A) from

muer (B), remove four screws that connect

guard to muer bracket.

2. Remove four screws that attach spark arrester

screen (C).

3. Inspect screen and obtain a replacement if torn,

perforated or otherwise damaged. DO NOT use a

defective screen. If screen is not damaged, clean

it with commercial solvent.

4. Reattach screen and muer guard.

Air Cooling System

Over time debris may accumulate in cylinder cooling

ns and cannot be observed without partial engine

disassembly. For this reason, we recommend you have

a qualied service dealer clean the cooling system per

recommended intervals (see Maintenance Schedule in

beginning of Maintenance section). Equally important

is to keep top of engine free from debris. See Clean

Debris.

Carburetor Adjustment

The carburetor on this engine is low emission. It is

equipped with a non-adjustable idle mixture valve.

Top speed has been set at the factory. If adjustment is

required, see an authorized service dealer.

A

B

C

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage

fuel tank causing a re, resulting in

death or serious injury.

Contact with muer area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (1.5 m) of clearance on all sides of

pressure washer including overhead.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

dened in Section 4442, maintained in eective working

order. Other states or federal jurisdictions may have

similar laws.

Contact the original equipment manufacturer, retailer,

or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

• Replacement parts must be the same and installed in the

same position as the original parts.

CAUTION

Excessively high operating speeds

could result in minor injury.

Excessively low speeds impose a heavy load.

• DO NOT tamper with governor spring, links or other parts to

increase engine speed. Pressure washer supplies correct

rated pressure and ow when running at governed speed.

• DO NOT modify pressure washer in any way.

La page charge ...

Briggs & Stratton Elite 3300 MAX PSI Manuel utilisateur

Ce manuel convient également à

Briggs & Stratton Elite 3300 MAX PSI Manuel utilisateur

dans d''autres langues

Autres documents