Shopmaster S26-260L Manuel utilisateur

S26-260L

Sierra ingletadora

compuesta de 10

pulgadas

Scie à onglet

Combine 254 mm

Instruction Manual

Manuel d’utilisation

Manual de instrucciones

Français (24)

Español (47)

www.DeltaMachinery.com

To reduce risk of serious injury, thoroughly read and comply with all warnings and instructions in this manual and on

product. KEEP THIS MANUAL NEAR YOUR SAW FOR EASY REFERENCE AND TO INSTRUCT OTHERS

10-INCH COMPOUND MITER SAW

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ................................... 2

Safety logos ......................................................................... 2

GENERAL POWER TOOL SAFETY RULES ............................ 3

PROPOSITION 65 ...................................................................... 4

MITER SAW SAFETY RULES ................................................... 4

POWER CONNECTIONS .......................................................... 5

Double Insulation ................................................................. 5

Electrical Connection .......................................................... 6

Polarized Plugs .................................................................... 6

Extension Cords .................................................................. 6

FEATURES ................................................................................ 6

Product Specifications ........................................................6

Know Your Compound Miter Saw ...................................... 7

UNPACKING ............................................................................. 8

ASSEMBLY ................................................................................. 9

Saw Arm Lock Pin ............................................................... 9

Attaching Miter Lock Knob ................................................. 9

Mounting the Saw to a Stable Surface ............................. 10

Attach Horizontal Work Clamp ..........................................10

Install Dust Collection Bag ................................................ 11

Install Batteries for Laser ................................................... 11

PREPARING YOUR SAW FOR USE .......................................12

Install/Replace the Blade .................................................. 12

Align the Blade to the Table .............................................. 13

Using the Laser Guide ....................................................... 14

To Remove Your Mark ............................................... 14

To Cut on Your Mark .................................................. 14

To Cut without Removing Your Mark ......................... 14

Free Warning Label Replacement ............................. 14

OPERATION ............................................................................. 15

Applications ....................................................................... 15

Power Switch Lock............................................................15

Cross Cuts .........................................................................16

Bevel Cuts .................................................................. 16

Compound Miter Cuts ............................................... 16

TIPS FOR CUTTING AND SUPPORTING WORKPIECES ....17

Tips for Cutting Crown Molding ........................................ 17

Cutting Warped Material ................................................... 18

Clamping Wide Workpieces .............................................. 18

Supporting Long Workpieces............................................19

ADJUSTMENTS ....................................................................... 19

Arm Pivot ........................................................................... 19

Positive Stop Screw ..........................................................19

Bevel Pivot ........................................................................ 20

Laser Guide ....................................................................... 20

MAINTENANCE ......................................................................21

Keep Machine Clean ......................................................... 21

General Maintenance ........................................................ 21

Lubrication ......................................................................... 21

Brush Replacement ........................................................... 21

TROUBLESHOOTING ............................................................. 22

Failure to Start ...................................................................22

ACCESSORIES ........................................................................ 22

PARTS, SERVICES AND WARRANTY ASSISTANCE ........... 22

Three-Year Limited Warranty .............................................22

Replacement Parts ............................................................ 23

Service and Repairs .......................................................... 23

French ................................................................................24

Spanish .............................................................................. 47

IMPORTANT SAFETY INSTRUCTIONS

CAREFULLY READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS ON YOUR

PRODUCT AND IN THIS MANUAL. SAVE THIS MANUAL. MAKE SURE ALL USERS ARE

FAMILIAR WITH ITS WARNING AND INSTRUCTIONS WHEN USING THE TOOL. Improper operation, maintenance or

modification of tools or equipment could result in serious injury and/or property damage.

If you have any questions or concerns relative to the use of your tool or the contents of this manual, stop using the tool

and contact Delta Power Equipment Corporation Customer Care at 1-800-223-7278.

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may

result in property damage.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

SAFETY LOGOS

This manual contains information that is important for you to know and understand. This information relates to protecting

YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the

symbols below. Please read the manual and pay attention to these sections.

2

Additional information regarding the safe and proper operation of this tool is available from the following sources:

• Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851or online at www.powertoolinstitute.com

• National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201

• American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org - ANSI 01.1 Safety Requirements

for Woodworking Machines

• U.S. Department of Labor regulations www.osha.gov

GENERAL POWER TOOL SAFETY RULES

• READ INSTRUCTION MANUAL AND KNOW

YOUR TOOL. Read and familiarize yourself with

entire instruction manual. Learning the tool’s proper

applications, limitations, and specific potential

hazards will greatly minimize the possibility of

accidents and injury. Make sure all users are familiar

with its warnings and instructions before using tool.

• KEEP GUARDS IN PLACE and in working order.

• REMOVE ADJUSTING KEYS AND WRENCHES.

Form habit of checking to see that all adjusting keys

and wrenches are removed before starting tool.

• KEEP WORK AREA CLEAN AND WELL LIT. Cluttered

or poorly lit work areas, surfaces and benches can

lead to accidents.

• DO NOT USE OR STORE TOOL IN DANGEROUS

ENVIRONMENTS. Exposure to rain and damp or

wet locations can result in shock or electrocution,

or damage the tool. Do not operate electric tools

near flammable liquids or in gaseous or explosive

atmospheres. Motors and switches in these tools

may spark and ignite fumes.

• KEEP CHILDREN AND BYSTANDERS AWAY from

work area.

• LOCK TOOLS AND WORK AREA. Use padlocks, and

master switches, or remove and store starter keys to

prevent operation by children and other unauthorized

users.

• DO NOT FORCE TOOL OR WORKPIECE. Operate

tool at intended speed and feed rate for better and

safer operation.

• USE PROPER TOOL. Do not force tool to do a task

for which it was not designed.

• DO NOT ABUSE POWER CORDS. NEVER pull on

cord to disconnect from receptacle, crush cord, or

expose it to heat, oil or sharp objects.

• USE PROPER EXTENSION CORD. If you use an

extension cord, make sure it is in good condition and

heavy enough to carry the current your product will

draw. An undersized cord will cause a drop in line

voltage, resulting in loss of power and overheating.

See Extension Cord Chart for correct size depending

on cord length and data plate ampere rating. If in

doubt, use the next smaller gauge number. The

smaller the gauge number, the heavier the cord.

When working outside, make sure extension cord

is rated for outdoor use. Consult power connection

section of this manual for Extension Cord Chart and

power connection safety.

• SECURE WORKPIECE. Use clamps or a vise to hold

the work piece when practical. It is safer than using

your hands and frees both hands to operate tool.

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.

• DO NOT OVERREACH. Keep proper footing and

balance to maintain control.

• MAINTAIN TOOLS WITH CARE. Keep tools sharp

and clean for best and safest performance. Follow

instructions for lubricating and changing accessories.

• DISCONNECT TOOLS before servicing; when

changing accessories, such as blades, or adjusting the

laser calibration..

• TO REDUCE RISK OF ACCIDENTAL STARTING, make

sure power switches are in “OFF” position before

plugging tool in.

• DO NOT touch the plug’s metal prongs when

unplugging or plugging in the cord.

• USE RECOMMENDED ACCESSORIES. Consult

manual for recommended accessories. Use of

inappropriate accessories may cause personal injury or

property damage.

• NEVER STAND ON TOOL. Serious injury could occur if

the tool tips or if you unintentionally contact the cutting

surface.

• CHECK TOOLS FOR DAMAGE. Before using, and

after tool or accessory has been dropped or damaged,

check guards and affected parts for alignment of

moving parts, binding of moving parts, breakage

of parts, and any other condition that may affect its

operation to make sure tool will operate properly and

all parts will perform their intended function. Do not

use a damaged product. A guard or any other part that

is damaged should be properly repaired or replaced

using factory approved service parts.

• USE PROPER FEED DIRECTION. Feed work piece

against the direction of rotation of the tool’s blade,

cutter, or abrasive surface. Feeding in the other

direction may cause the work piece to be thrown at

high speed.

• NEVER LEAVE TOOL RUNNING UNATTENDED. TURN

POWER OFF. Do not leave tool until it comes to a

complete stop. In the event of a power failure, move

switch to “OFF” position.

• STAY ALERT; WATCH WHAT YOU ARE DOING, AND

USE COMMON SENSE. Do not use power tools

when tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating

power tools may result in injury.

• SERVICE PARTS. Use only identical replacement parts

when servicing your tool.

• WEAR PROPER APPAREL. Do not wear loose clothing,

gloves, neckties, rings, bracelets, or other jewelry

which may get caught in moving parts. Nonslip

protective footwear is recommended. Wear protective

hair covering to contain long hair.

3

• WEAR PROPER EYE PROTECTION. All persons

in work area should wear safety glasses with side

shields. Everyday eyeglasses with impact resistant

lenses are not safety glasses. Eye equipment should

comply with ANSI Z87.1 standards.

• HEARING PROTECTION. All people in work area

should wear proper hearing protection consistent with

noise levels and exposure. Hearing equipment should

comply with ANSI S3.19 standards.

• DUST PROTECTION. Use of power tools can

generate and/or disburse dust, which may cause

serious and permanent respiratory or other injury,

including silicosis (a serious lung disease), cancer,

and death. Direct articles away from face and body.

Always operate tool in well-ventilated area and

provide for proper dust removal. Use dust collection

system whenever possible. Avoid breathing dust and

avoid prolonged contact with dust. Allowing dust

to get into your mouth or eyes, or lay on your skin

may promote absorption of harmful chemicals. Use

properly fitting NIOSH/OSHA approved respiratory

protection appropriate for the dust exposure and

wash exposed areas with soap and water.

• Replace the warning labels if they become obscured

or removed.

• This machine is designed and intended for use by

properly trained and experienced personnel only.

If you are not familiar with the proper and safe

operation of this product, do not use until proper

training and knowledge have been obtained.

• KEEP GUARDS AND SAFETY DEVICES IN PLACE

and working properly.

Failure to follow these rules may result in serious personal injury.

• SEE GENERAL POWER TOOL SAFETY SECTION OF THIS MANUAL. Read entire instruction manual before operating

saw. Learning the saw’s proper applications, limitations, and specific potential hazards will greatly minimize the

possibility of accidents and injury. Make sure all users are familiar with its warnings and instructions before using saw.

• SEE POWER CONNECTION SECTION OF THIS MANUAL for instructions and warnings regarding power cord and

connections.

• FIRMLY CLAMP OR BOLT your machine to a

workbench or table at approximately hip height. The

saw can tip over if the saw head is released suddenly

and the saw is not secured to a work surface.

• KEEP HANDS AWAY FROM CUTTING AREA. Do not

reach underneath work or in blade cutting path with

your hands and fingers for any reason.

• ALWAYS SUPPORT LONG WORKPIECES while

cutting to minimize risk of blade pinching and

kickback.

• USE A CLAMP to secure the workpiece when

possible.

• NEVER START THE SAW with the blade touching

the workpiece. Allow motor to come up to full speed

before starting cut.

• NEVER cut more than one piece at a time. DO NOT

PLACE more than one workpiece on the saw table at

a time.

• MAKE SURE THE MITER TABLE AND BEVEL

ADJUSTMENTS ARE LOCKED IN POSITION

GENERAL POWER TOOL SAFETY RULES

CALIFORNIA PROPOSITION 65

4

MITER SAW SAFETY RULES

Some dust created by power sanding, sawing, grinding, drilling and other construction activities

contains chemicals known to the state of California to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and other masonry products, and

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to

these chemical: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that

are specially designed to filter out microscopic particles.

BEFORE OPERATING YOUR SAW. Lock the miter

table by securely tightening the miter lock levers.

Lock the saw arm by securely tightening the bevel

lock knob.

• NEVER USE A LENGTH STOP ON THE FREE SCRAP

END OF A CLAMPED WORKPIECE. NEVER hold

onto or bind the free scrap end of the workpiece in

any operation. If a work clamp and length stop are

used together, they must both be installed on the

same side of the saw table to prevent the saw blade

from contacting the cut off piece.

• NEVER PERFORM ANY OPERATION FREEHAND.

Always place the workpiece to be cut on the miter

table and position it firmly against the fence as a

backstop. Always use the fence.

• NEVER reach behind, under, or within three inches of

the moving blade and its cutting path with hands and

fingers for any reason.

• NEVER reach to pick up a workpiece, a piece of

scrap, or anything else that is in or near the cutting

path of the blade, while the saw is running or the

blade is turning.

• NEVER move the workpiece or make adjustment

to any cutting angle while the saw is running or the

blade is rotating.

• AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause your

hand to move into the blade. ALWAYS make sure you

have good balance. NEVER operate the miter saw on

the floor or in a crouched position.

• ALWAYS release the power switch and allow the

saw blade to stop rotating before raising it out of the

workpiece or changing settings.

• IF ANY PART OF THIS MITER SAW IS MISSING or

should break, bend, or fail in any way, or should any

electrical component fail to perform properly, shut off

the power switch, remove the miter saw plug from the

power source and have damaged, missing, or failed

parts replaced before resuming operation.

• ALWAYS STAY ALERT! Do not allow familiarity

(gained from frequent use of the saw) to cause

a careless mistake. ALWAYS REMEMBER that a

careless fraction of a second is sufficient to inflict

severe injury.

• IF THE POWER SUPPLY CORD IS DAMAGED, it

must be replaced by an authorized service center or

electrician.

• NEVER leave the saw unattended while connected to

a power source.

• ALWAYS carry the tool only by the base.

• AVOID direct eye exposure when using the laser

guide.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should

be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have

3-prong grounding type plugs. Before connecting the machine to the power line, make sure the switch (s) is in the

"OFF" position and be sure that the electric current is of the same characteristics as indicated on the machine. All line

connections should make good contact. Running on low voltage will damage the machine.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP OR

WET LOCATIONS.

Your machine is wired for 120 volts, 60 HZ alternating current. Before connecting the machine to the power source,

make sure the switch is in the "OFF" position.

DOUBLE INSULATION

The double insulated system is designed to protect the user from shock resulting from a break

in the tool’s internal insulation. However, it is important to observe normal safety precautions

to avoid electrical shock.

NOTE: Servicing of a tool with double insulation requires extreme care and knowledge of the system and should be

performed only by a qualified service technician. For service, we suggest you return the tool to the nearest authorized

service center for repair. Always use identical replacement parts when servicing.

NOTE: The manual cover illustrates the current production model. All other illustrations contained in the manual are

representative only and may not be exact depictions of the actual labeling or accessories included. They are intended for

illustrative purposes only.

5

MITER SAW SAFETY RULES

ELECTRICAL CONNECTION

This tool has a precision-built electric motor. It should be connected to a POWER SUPPLY THAT IS 120 VOLTS, 60 HZ,

AC ONLY (NORMAL HOUSEHOLD CURRENT).

Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power

and the motor will overheat. If the tool does not operate when plugged into an outlet, double-check the

power supply.

POLARIZED PLUGS

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug

will fit in a polarized plug only one way. If the plug does not fully fit in the outlet reverse the plug. If it still does not fit,

contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

EXTENSION CORDS

When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has

the capacity to handle the current the tool will draw. An undersized cord will cause a drop in line voltage, resulting in

overheating and loss of power. Use the chart to determine the minimum wire size required in an extension cord. Only

round jacketed cords listed by Underwriter’s Laboratories (UL) should be used. When working outdoors with a tool,

use an extension cord that is designed for outside use. This type of cord is designated with “WA” on the cord’s jacket.

Before using any extension cord, inspect it for loose or exposed wires and cut

or worn insulation.

Keep the extension cord clear of the work area. Position the

cord so that it will not get caught on lumber, tools or other

obstructions while you are working with a power tool. Failure to do so can

result in serious personal injury. Check extension cords before each use. If

damaged replace immediately. Never use tool with a damaged cord, since

touching the damaged area could cause electrical shock resulting in serious

injury.

**Ampere rating (on tool data label)

12A – 16A

Cord Length Wire Size

25' 14 AWG

50' 12 AWG

** Used on 12 guage - 20 am circuit

NOTE: AWG = American Wire Guage

PRODUCT SECIFICATIONS

POWER CONNECTIONS

6

FEATURES

Cutting Capacity

(maximum nominal

lumber sizes)

0º Miter/0º Bevel: 2"x6" or 4"x4"

45º Miter/0º Bevel: 2"x4"

0º Miter/45º Bevel: 2"x6"

45º Miter/45º Bevel: 2"x4"

Net Weight

31lbs

Input

120V~, 60hz, 15 Amps

Blade Arbor

5/8"

Blade Diameter

10"

No Load Speed

5,500 r/min (RPM)

KNOW YOUR COMPOUND MITER SAW

Refer to Figure 1.

Using this tool safely requires that you understand the

information provided in this operator’s manual, as well as

the project you are attempting. Before using this product,

familiarize yourself with all operating features and safety

rules.

A. 15-AMP MOTOR: This tool features a powerful

15-amp motor with all ball bearings and externally

accessible brushes for ease of servicing.

B. FENCE: The miter fence supports the workpiece when

making all cuts.

C. THROAT PLATE: The throat plate supports the

workpiece and provides a safe working surface.

D. MITER LOCK: The miter lock handle securely locks

the saw at desired miter angles.

E. MITER CONTROL ARM: Is mounted to the Work Table

and provides a stable connection in order to pivot the

Work Table at the desired miter angle.

F. MITER GAUGE WITH POSITIVE STOPS: Positive

stops have been provided at 0°, 15°, 22-1/2°, 31.6°,

and 45°. The positive stops have been provided on

both the left and right side of the miter table.

G. HORIZONTAL WORK CLAMP: The horizontal work

clamp helps to position and secure the workpiece to

the fence, ensuring safer operation and more accurate

cuts.

H. BASE: Supports the tool and features mounting holes.

I. MOUNTING HOLES: Enable you to securely mount

the tool to a stable surface.

J. BLADE WRENCH STORAGE: The included blade

wrench features a Phillips screwdriver at one end and

a hex key at the other. Use the hex key when installing

or removing blade and the Phillips screwdriver when

removing or loosening screws. When not in use, the

wrench can be stored in the base of the saw.

K. WORK TABLE: The die-cast aluminum work table

provides a level and sturdy work surface.

L. BEVEL LOCK: The bevel lock secures the saw at the

desired angle for bevel cuts. There are positive stop

screws on each side of the saw arm for making fine

adjustments at 0° and 45°.

M. DUST COLLECTION BAG: The included dust bag

attaches and detaches quickly with the integrated

clamp for easy cleaning.

7

FIGURE 1

A. Motor

B. Fence

C. Throat Plate

D. Miter Lock

E. Miter Control Arm

F. Miter Gauge with Positive Stops

G. Horizontal Work Clamp

H. Base

I. Mounting Holes

J. On-Board Wrench

K. Work Table

L. Bevel Lock

M. Dust Bag

N. Upper and Lower Blade Guards

O. Blade (not visible)

P. Trigger Switch

Q. Spindle Lock

R. Electric Brake (not shown)

S. Laser Guide (not shown)

FEATURES

A

K

B

G

L

CD

P M

H

I

QN

O

F

x4

E

J

N. UPPER AND LOWER BLADE GUARDS: The lower

blade guard is made of shock-resistant, see-through

plastic that provides protection from each side of the

blade. It automatically retracts over the upper blade

guard as the saw is lowered into the workpiece.

O. 10-INCH BLADE: A 10 in. blade is included with the

compound miter saw. It will cut materials up to 3-1/2

in. thick or 5-1/2 in. wide, depending upon the angle

at which the cut is being made.

P. POWER SWITCH: The saw blade is activated by

an easy-to-use switch. When not in use the saw

should be disconnected from the power supply and

switch locked in the off position using a padlock

(not included) inserted through the hole in the switch

trigger. A lock with a long shackle up to 5/16 in.

diameter may be used. The padlock and key should

be stored in separate locations.

Q. SPINDLE LOCK BUTTON: The spindle lock button

locks the spindle preventing the blade from rotating

while removing or installing the blade screw.

R. ELECTRIC BRAKE: An electric brake has been

provided to more quickly stop blade rotation after the

switch is released. (not shown)

S. LASER GUIDE: For more accurate cuts, a laser guide

is included with your miter saw. When used properly,

the laser guide makes accurate, precision cutting

simple and easy. (not shown)

8

Check shipping carton and machine for damage before unpacking. Carefully remove packaging materials, parts and

machine from shipping carton. Always check for and remove protective shipping materials around motor and moving

parts. Lay out all parts on a clean work surface.

Compare the items to inventory figures; verify that all items are accounted for before discarding the shipping carton.

Report any missing or damaged parts, please call Company’s Customer Care Center at 800-223-7278. Prior to tool

assembly and use, read this manual thoroughly to familiarize yourself with proper assembly, maintenance and safety

procedures.

If any parts are missing, do not attempt to plug in the power cord and turn the power on. The saw should only be

energized after all parts have been located and correctly assembled.

UNPACKING

CONTENTS DESCRIPTION (QTY)

A. SHOPMASTER S26-260L 10-inch compound miter

saw (1)

B. Dust collection bag (1)

C. Horizontal Work Clamp (1)

FEATURES

D. Miter Lock Knob (1)

E. Blade Wrench (1)

F. AAA Batteries (2)

G. Operator’s Manual (not shown) (1)

A F

E

D

C

B

9

SAW ARM LOCK PIN

1. The saw is shipped with the arm secured in the down

position as shown in Figure 2. To release the arm,

push it down, cut the plastic tie and release the lock

pin (A).

2. Lock pin (A) is for storage and transport only. Saw is

not to be locked in down position during cuts.

3. Inspect the tool carefully to make sure no damage

occurred during shipping.

4. Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

tool.

ASSEMBLY

• Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or

modification is misuse and could result in a hazardous condition.

• Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting.

• Do not start the miter saw without checking for interference between the blade and the miter fence. Damage could result

to the blade if it strikes the miter fence during operation of the saw.

• This saw can tip over if the saw head is released suddenly and the saw is not secured to a work surface. ALWAYS secure

this saw to a stable work surface before any use.

• If any parts are damaged or missing do not operate this tool until the parts are replaced. Please call Customer Care

Center at 800-223-7278, for instructions.

ATTACHING MITER LOCK KNOB

1. See Figure 3 and attach the miter lock

knob by screwing the end of the miter lock

handle (B) into the threaded hole (C) in the control

arm. Tighten by rotating the lock knob clockwise.

FIGURE 3

A

FIGURE 2

TIGHTEN

B

C

10

ATTACH HORIZONTAL WORK CLAMP

The horizontal work clamp secures the workpiece to the

fence to provide more stability and keeps the workpiece

from creeping toward the saw blade. To install the

horizontal work clamp, see Figure 5 and do the following:

1. Place the clamp shaft (B) in either hole (C) on the

miter table base.

2. Rotate the knob (D) on the clamp clockwise to move

it in or counterclockwise to move it out as needed.

ASSEMBLY

FIGURE 4

FIGURE 5

To ensure safe and accurate operation,

this saw should be mounted to a stable

and level surface such as a workbench. To mount the tool

to a stable surface, refer to Figure 4 and do the following:

1. Locate the four mounting holes in the base of the saw

(A).

2. Secure the tool to the mounting surface using 3/8”

diameter machine bolts, lock washers, and hex nuts

(not included). Make sure the bolts are long enough to

accommodate the saw base, lock washers, hex nuts,

and the thickness of the workbench.

3. Tighten all four bolts securely.

4. Check to make sure that the saw is secure before

operation.

MOUNTING THE SAW TO A

STABLE SURFACE

A

D

B

C

11

ASSEMBLY

INSTALL DUST COLLECTION BAG

The tool includes a dust collection bag that attaches

over the exhaust port on the upper blade guard.

See Figure 6, then:

1. Squeeze the two metal clips (A) at the mouth of the

bag.

2. Slide the clips over it the exhaust port (B) until the

metal ring in the bag locks between the grooves on

the exhaust port.

NOTE: To remove the dust bag for emptying, simply

reverse the above procedure.

FIGURE 7

FIGURE 6

INSTALL BATTERIES FOR LASER

1. The battery compartment (C) is located in the control

arm on the top of the saw handle.

2. Using the Phillips end of the supplied blade wrench,

remove the screw (D) securing the compartment

cover and lift off the cover.

3. Install two AAA batteries (supplied) as shown on the

diagram in the compartment.

4. Replace the cover and secure with the screw.

Laser radiation. Avoid direct eye

contact with light source.

B

A

D

C

12

PREPARING YOUR SAW FOR USE

FIGURE 8

FIGURE 9

Refer to Figure 9.

4. Press and hold the spindle lock button (E).

5. Carefully rotate the old blade until the spindle locks in

place.

6. Using the supplied blade wrench, remove the blade

bolt (D) by turning it clockwise.

NOTE: The blade bolt has left-hand threads.

7. Remove only the outer blade washer (F) and the

blade (G), leaving the inner blade washer on the

spindle.

If inner blade washer has been

removed, replace it before placing

blade on spindle. Failure to do so could cause an

accident since blade will not tighten properly.

8. Carefully fit saw blade inside the lower blade guard

and guide it onto spindle, ensuring the teeth of the

blade are facing down at the front of the saw.

9. Align the double “D” flats on the blade washer (F) with

the flats on the spindle and fit the washer onto the

spindle.

10. Lock the spindle by depressing the spindle lock

button (E). Replace blade bolt, remembering to thread

it counterclockwise. Tighten blade bolt securely.

Always install the blade with the blade

teeth and the arrow printed on the side

of the blade pointing down at the front of the saw. The

direction of blade rotation is also stamped with an arrow

on the upper blade guard.

11. Replace the blade bolt cover and tighten blade bolt

cover screw securely. Lower blade guard

12. Raise and lower the saw arm to ensure that the arm

and blade guard move freely.

Make sure the spindle lock button is not

engaged before reconnecting saw to

power source. Never engage spindle lock button when

blade is rotating.

NOTE: Some illustrations in this manual indicate only

portions of the saw. This is done in order to more clearly

show keys areas and components of the saw. Never

operate the saw without all guards securely in place and

in good operating condition.

INSTALL/REPLACE THE BLADE

A 10-inch blade is the maximum blade

capacity of the saw. Larger blades will

come in contact with the blade guards.

Refer to Figure 8.

1. Make sure the saw is unplugged.

2. Raise the saw arm to the full upright position.

3. Rotate lower blade guard (A) up. Slightly loosen the

blade bolt cover screw (B) until you can move the

blade bolt cover (C) up to expose the blade bolt. (D)

D

B

C

A

F

G

E

13

PREPARING YOUR SAW FOR USE

FIGURE 12

FIGURE 13

FIGURE 14

ALIGN THE BLADE TO THE

TABLE

Refer to Figure 12.

1. Unplug the saw.

2. Lower the saw arm all the way down to the transport

position and engage the lock pin to hold it in place.

3. Loosen the miter lock handle (A), and position the

table so that the miter scale indicator (B) reads 0°.

4. Tighten the miter lock handle so that the table will not

move.

5. Loosen bevel lock knob (C) and adjust the angle

of the saw arm so that the bevel scale indicator (D)

reads 0°. This positions the blade at 90° to table.

6. Securely tighten bevel lock knob.

Refer to Figure 13.

7. Place a combination square (E) against the table and

the face of the saw blade (F) square contacts the flat

part of the saw blade, not the blade teeth.

8. Rotate the blade by hand and check the blade-to-

table alignment at several points.

9. The edge of the square and the saw blade should be

parallel as shown in Figure 13.

10. If the top or bottom of the blade face is not flush with

the square, refer to Figure 14 below and perform the

following steps.

Refer to Figure 14.

11. Loosen bevel lock knob (G).

12. Adjust positive stop adjustment screw (H) to bring

saw blade into alignment with the square. See

“Positive Stop Screw” in the Adjustment section.

13. Retighten bevel lock knob. Recheck blade-to-table

alignment.

NOTE: The above procedure can be used to check

alignment of the blade to the miter table at both 0° and

45° angles.

NOTE: The saw has two scale indicators, one on the

bevel scale and one on the miter scale. After squaring

adjustments have been made, it may be necessary to

loosen the indicator screws and reset them to zero.

A

B

D

C

E F

H

G

14

PREPARING YOUR SAW FOR USE

USING THE LASER GUIDE

When the laser guide switch is turned on it projects a red

line onto the work surface enabling you to see your cut

before you make it. To ensure a true and straight cut:

1. Make sure the saw is unplugged.

2. Draw a line on the workpiece where you plan to cut.

3. Flip the laser switch (A) to the “ON” position.

4. The red line (B) indicates the path of the blade.

5. Align the laser line and the mark with the blade at the

uppermost position.

6. Once both lines are in alignment, do not move the

workpiece.

7. Plug the saw into the power source.

8. Make several practice cuts on different styles and

thickness of material.

9. Repeat the steps above as necessary.

TO REMOVE YOUR MARK:

Position the laser line near the left edge of your mark on

the work surface in order to cut through the mark.

TO CUT ON YOUR MARK:

Position the laser line near or over your mark on the work

surface in order to cut the mark.

TO CUT WITHOUT REMOVING YOUR

MARK:

Position the laser line near the right edge of your mark on

the work surface in order to leave the mark.

After you have become familiar with using the laser

guide, you will be able to remove, cut, or leave your mark

on the work surface. Practice will teach you the correct

position for aligning the laser line with your mark.

FIGURE 15

B

A

FREE WARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing,

call1-800-223-7278 for a free replacement.

• Avoid direct eye exposure to laser beam or reflection.

Intense or prolonged exposure to laser radiation

could permanently damage your eyes. Do not project

or reflect the laser into anyone’s eyes, including your

own.

• Caution -- use of controls or adjustments or

performance of procedures other than those

specified herein may result in hazardous radiation

exposure.

• Do not disassemble or modify the laser. There are no

user serviceable parts inside. Serious eye injury could

result.

• Use or modification of the laser guide for anything

other than its designed purpose may result in

hazardous radiation exposure.

EXAMPLE SERIAL NUMBER, FOR

REFERENCE ONLY

Model No.

S26-260L

10-In Miter Saw

LISTED

D

PEC

004575

5J65 E129484

14A0000012114O1CT

15

OPERATION

14A0000012114O1CT

Failure to heed this warning can result in serious personal injury.

•

Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient

to inflict serious personal injury.

•

Always wear eye protection with side shields and marked to comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes, resulting in possible serious personal injury.

•

Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of

attachments or accessories not recommended can result in serious personal injury.

•

Before starting any cutting operation, clamp or bolt the compound miter saw to a workbench. Never operate the

miter saw on the floor or in a crouched position.

•

Always tighten the miter lock handle and bevel lock knob securely before making a cut. Failure to do so could result

in movement of the control arm or miter table while making a cut.

•

Keep hands outside the no hands zone, at least 3 in. from blade. Never perform any cutting operation freehand

(without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists.

•

When using a work clamp or C-clamp to secure the workpiece, clamp workpiece on one side of the blade only. The

workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece. The workpiece

binding the blade will cause motor stalling and kickback. This situation could cause an accident resulting in possible

serious personal injury.

•

NEVER move the workpiece or make adjustment to any cutting angle while the saw is running and the blade is

rotating. Any slip can result in contact with the blade.

APPLICATIONS

You may use this tool for the following purposes:

•

Bevel cutting and compound cutting for crown moldings, etc.

•

Cross cutting wood and plastic

•

Cross cutting for moldings, door casings, picture frames, etc.

NOTE: The blade provided is acceptable for most cutting of lumber and moldings, but for fine joinery cuts or cutting

plastic, it is recommended that you use a specialty blade designed for these applications.

FIGURE 16

POWER SWITCH LOCK

To prevent any unauthorized person from operating this

saw, a padlock (not included) may be installed into the

lock hole located on the power switch, as shown in

Figure 16. Be sure padlock is fully closed and locked

before leaving saw unattended.

Always disconnect the power supply

before installing or removing a lock onto

the power switch. Failure to do so could cause the power

switch to engage by accident, resulting in serious injury.

16

OPERATION

CROSS CUTS

A cross cut is a cut made across the grain of the

workpiece. A straight cross cut means the miter scale

indicator is set at 0°. For a miter cross cut, the miter scale

indicator is set at an angle other than 0°.

Refer to Figure 17.

1. Disengage the lock pin (A) and lift saw arm to its full

height.

2. For a straight cross cut, skip to step 5.

3. To make a miter cross cut, loosen the miter lock

handle (B).

4. Rotate the control arm until the pointer aligns with the

desired angle on the miter scale (C) then tighten the

miter lock handle securely.

5. Place the workpiece flat on the table with one edge

securely against the fence. If the board is warped,

place the convex side against the fence. If the

concave edge of a board is placed against the fence,

the board could collapse on the blade at the end of

the cut, jamming the blade.

6. When cutting long pieces of lumber or molding,

support the opposite end of the stock with a roller

stand or with a work piece support that is level

with the table surface. See SUPPORTING LONG

WORKPIECES (Page 20).

7. Align cutting line on workpiece with edge of saw

blade or laser line.

8. Grasp the stock firmly with one hand and secure it

against the fence. Use the optional work clamp (D)

9. Before turning on the saw, practice the cut to ensure

no problems will occur when the cut is made.

10. Hold the saw handle firmly and squeeze the power

switch. Wait until the blade reaches maximum speed

before making cut.

11. Slowly lower the blade into and through the

workpiece.

12. Release the power switch and allow the blade to stop

rotating before raising the blade out of workpiece.

13. Wait until the electric brake stops blade from turning

before removing the workpiece from the table.

BEVEL CUTS

A bevel cut is made across the grain with the blade

angled to the workpiece. A straight bevel means the miter

scale indicator is set at 0° and the bevel scale indicator is

set at an angle other than 0°.

COMPOUND MITER CUTS

A compound miter cut is a cut made using a miter angle

and a bevel angle at the same time. Adjustments of miter

and bevel settings are interdependent. Each time you

adjust the miter setting you change the effect of the bevel

setting. Also, each time you adjust the bevel setting you

change the effect of the miter setting.

FIGURE 17

A

BD

C

17

TIPS FOR CUTTING AND SUPPORTING WORKPIECES

TIPS FOR CUTTING CROWN MOLDING

• The two edges of the molding that contact the ceiling and the wall are at angles that, when added together, equal exactly

90°. Most crown molding has a top rear angle (the section that fits flat against the ceiling) of 52° and a bottom rear angle

(the section that fits flat against the wall) of 38°.

• To accurately cut crown molding for a 90° inside or outside corner, lay the molding with its broad back surface flat on the

miter table and against the fence.

• The angles for crown moldings must be very precise. The bevel and miter angles are interdependent; changing one angle

changes the other angle as well.

• Since it is very easy for the work piece to shift, all settings should first be tested on scrap molding. Also most walls do not

have angles of exactly 90°; therefore, you will need to fine-tune your settings.

• When cutting crown molding the bevel angle should be set at 33.85°.

• The miter angle should be set at 31.62° either right or left, depending on the desired cut for the application. See the chart

below for correct angle settings and correct positioning of crown molding on the work table.

Bevel Angle Setting Type of Cut Steps

33.85° Left side, inside corner 1. Top edge of molding against fence

2. Miter table set right 31.62°

3. Save left end of cut

33.85° Right side, inside corner 1. Bottom edge of molding against fence

2. Miter table set left 31.62°

3. Save left end of cut

33.85° Left side, outside corner 1. Bottom edge of molding against fence

2. Miter table set left 31.62°

3. Save right end of cut

33.85° Right side, outside corner 1. Top edge of molding against fence

2. Miter table set right 31.62°

3. Save right end of cut

18

TIPS FOR CUTTING AND SUPPORTING WORKPIECES

CUTTING WARPED MATERIAL

When attempting to cut warped material, the CONVEX

face should be against the fence as shown in Figure 18.

CLAMPING WIDE WORKPIECES

When cutting wide work pieces, such as 2 in. x 6 in.,

clamp the workpiece to the work table using a C-clamp

as shown in Figure 20.

Keep clamps away from the path of the

blade and blade guard assembly.

To avoid a kickback and to avoid serious

personal injury, never position the

concave edge of bowed or warped material against the

fence.

FIGURE 18

FIGURE 19

FIGURE 20

X

Never position a piece of warped material with the

CONCAVE face or edge against the fence, as shown in

Figure 19. It will pinch the blade near the completion of

the cut.

19

TIPS FOR CUTTING AND SUPPORTING WORKPIECES

ADJUSTMENTS

SUPPORTING LONG WORKPIECES

Long workpieces need extra support. Supports should

be placed along the workpiece so it does not sag. The

support should let the workpiece lay flat on the base of

the saw and work table during the cutting operation as

shown in Figure 21. Use the optional work clamp or a

C-clamp to secure the workpiece to the miter saw table.

Keep clamps away from the path of the

blade and blade guard assembly.

Before performing any adjustment,

make sure the tool is unplugged from

the power supply. Failure to heed this warning could

result in serious personal injury.

Your compound miter saw has been properly adjusted

at the factory. Due to shipping or normal use, it may

be necessary to re-adjust some of the settings. Check

the following adjustments periodically to assure proper

accuracy and safe operation.

Check for interference between the

blade and the throat plate, before

plugging the saw into the power source.

ARM PIVOT

The arm of the saw should raise and lower completely

and freely. In the lowered position and with the lock

pin removed, the arm should rise to the up position by

itself. If the saw arm does not raise by itself or if there is

play in the pivot joints, it will need to be professionally

repaired at an AUTHORIZED SERVICE CENTER. Please

call Company’s Customer Care Center at 800-223-7278.

POSITIVE STOP SCREW

The position of the positive stop adjustment screw

was set at the factory and normally will not require

readjustment. If the blade is not square to the table, the

positive stop adjustment screw must be re-adjusted.

To adjust refer to Figure 22:

1. Unplug the saw.

2. Loosen the bevel lock knob (B) by turning it

counterclockwise.

3. Using the Phillips end of the blade wrench, adjust the

positive stop adjustment screw (A).

4. Square the blade to the miter table as described

in the section entitled, ALIGN THE BLADE TO THE

TABLE, found on page 14.

5. Retighten bevel lock knob. Recheck blade-to-table

alignment.

6. The saw has two scale indicators, one on the bevel

scale and one on the miter scale. After squaring

adjustments have been made, it may be necessary to

loosen the indicator screws and reset them to zero.

NOTE: Use this procedure to check that the blade is

square to the table at 0° and 45° angles.

FIGURE 21

FIGURE 22

A

B

45°0°

20

Laser radiation. Avoid direct eye contact

with light source.

BEVEL PIVOT

With the bevel lock knob loosened, the control arm of the

saw should tilt easily from 0° and 45°. If it does not or if

there is play in the pivot, the saw must be repaired by an

AUTHORIZED SERVICE CENTER.

LASER GUIDE

Refer to Figure 23.

1. Secure a piece of scrap material to the table surface

using the work clamp or a C-clamp.

2. Plug the saw into the power source and make a slight

cut to score the wood.

3. Release the power switch and make sure the blade

comes to a full stop, then raise the saw arm to the

upright position.

4. Unplug the saw. Do not remove the scrap piece.

5. Turn on the laser switch (A). If properly aligned, the

laser should align with the left edge of the partial cut

you just made. If the laser does not align with the

left edge of the cut you will need to adjust the laser

alignment.

6. To adjust the left to right laser offset refer to Figure

24 and follow these instructions: using a Phillips

head screwdriver loosen screw (B) and slide the

laser bracket to the desired position. Make sure to

re-tighten screw (B) after adjusting.

7. To adjust the left to right laser angle refer to Figure 25

and follow these instructions: using the included hex

wrench, turn screw (C) to the desired angle (parallel to

the blade).

8. Once adjusted recheck alignment of laser line to cut

made in scrap material.

FIGURE 23

FIGURE 25

FIGURE 24

A

C

B

ADJUSTMENTS

La page charge ...

Shopmaster S26-260L Manuel utilisateur

Shopmaster S26-260L Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents