Dometic PerfectView CAM50 Mode d'emploi

CAM50

Rear View Video Camera

Installation and Operating Manual. . . . . . . . 9

Rückfahrvideokamera

Montage- und Bedienungsanleitung . . . . .23

Caméra vidéo de recul

Instructions de montage

et de service . . . . . . . . . . . . . . . . . . . . . . . . .37

Cámara de vídeo de marcha atrás

Instrucciones de montaje y de uso . . . . . . .52

Câmara de marcha-atrás

Instruções de montagem e manual de

instruções . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Videocamera per la retromarcia

Istruzioni di montaggio e d’uso . . . . . . . . . 81

Achteruitrijvideocamera

Montagehandleiding en

gebruiksaanwijzing . . . . . . . . . . . . . . . . . . .95

Bakvideokamera

Monterings- og betjeningsvejledning . . .109

Backningsvideokamera

Monterings- och bruksanvisning . . . . . . .122

Ryggevideokamera

Monterings- og bruksanvisning . . . . . . . .135

Peruutusvideokamera

Asennus- ja käyttöohje . . . . . . . . . . . . . . . 148

Видеокамера заднего вида

Инструкция по монтажу

и эксплуатации . . . . . . . . . . . . . . . . . . . . . 162

Kamera cofania

Instrukcja montażu i obsługi. . . . . . . . . . . 177

Cúvacia kamera

Návod na montáž a uvedenie

do prevádzky. . . . . . . . . . . . . . . . . . . . . . . 191

Couvací kamera

Návod k montáži a obsluze . . . . . . . . . . . 204

Tolatókamera

Szerelési és használati útmutató . . . . . . . 218

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

DRIVING SUPPORT

PERFECTVIEW

CAM50-IO-16S.book Seite 1 Donnerstag, 1. September 2016 3:16 15

CAM50-IO-16S.book Seite 2 Donnerstag, 1. September 2016 3:16 15

CAM50

3

1 2 3

4

9

6

8

5

7

10 11

12

1

CAM50-IO-16S.book Seite 3 Donnerstag, 1. September 2016 3:16 15

CAM50

4

2

3

4

5

6

7

CAM50-IO-16S.book Seite 4 Donnerstag, 1. September 2016 3:16 15

CAM50

5

1

3

2

5

6

4

8

3

2

1

9

CAM50-IO-16S.book Seite 5 Donnerstag, 1. September 2016 3:16 15

CAM50

6

90°

0

a

b

c

d

e

CAM50-IO-16S.book Seite 6 Donnerstag, 1. September 2016 3:16 15

CAM50

7

f

~50°

g

A B

h

i

A

B

j

CAM50-IO-16S.book Seite 7 Donnerstag, 1. September 2016 3:16 15

CAM50

8

k

CAM50-IO-16S.book Seite 8 Donnerstag, 1. September 2016 3:16 15

EN

CAM50

9

Please read this instruction manual carefully before installation and first

use, and store it in a safe place. If you pass on the product to another

person, hand over this instruction manual along with it.

Contents

1 Explanation of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

5 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

6 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

7 Notes on the electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

8 Mounting the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

9 Cleaning and caring for the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

10 Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

11 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

12 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

CAM50-IO-16S.book Seite 9 Donnerstag, 1. September 2016 3:16 15

EN

Explanation of symbols CAM50

10

1 Explanation of symbols

!

A

I

2 Safety and installation instructions

Please observe the prescribed safety instructions and stipulations from the

vehicle manufacturer and service workshops.

The manufacturer accepts no liability for damage in the following cases:

• Faulty assembly or connection

• Damage to the product resulting from mechanical influences and excess voltage

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in the operating manual

Please observe the following instructions:

• To prevent short circuits, always disconnect the negative terminal of the vehicle’s

electrical system before working on it.

If the vehicle has an additional battery, its negative terminal should also be

disconnected.

• Insufficient supply line connections could result in short circuits which

–Cause cable fires

– Trigger the airbags

– Damage electronic control devices

– Cause electric functions to fail (indicators, brake light, horn, ignition, lights)

WARNING!

Safety instruction: Failure to observe this instruction can cause fatal or

serious injury.

CAUTION!

Safety instruction: Failure to observe this instruction can lead to injury.

NOTICE!

Failure to observe this instruction can cause material damage and impair

the function of the product.

NOTE

Supplementary information for operating the product.

CAM50-IO-16S.book Seite 10 Donnerstag, 1. September 2016 3:16 15

EN

CAM50 Safety and installation instructions

11

• When working on the following lines, only use insulated cable lugs, plugs and

tab sleeves:

– 30 (direct supply from positive battery terminal)

– 15 (connected positive terminal, behind the battery)

– 31 (return line from the battery, earth)

– 58 (reversing light)

Do not use porcelain wire connectors.

• Use a crimping tool (fig. 1 10, page 3) to connect the cables.

• When connecting to supply line 31 (earth), screw the cable

– To the vehicle’s earth bolt with a cable lug and a gear disc or

– To the sheet metal body work with a cable lug and a self-tapping screw.

Ensure that there is a good earth connection.

When the negative terminal of the battery is disconnected, all data stored in the

volatile memories will be lost.

• The following data must be set again, depending on the vehicle equipment

options:

–Radio code

– Vehicle clock

–Timer

– On-board computer

– Seat position

You can find instructions for making these settings in the appropriate operating

instructions.

Observe the following installation instructions:

• Secure the parts of the camera installed in the vehicle in such a way that they

cannot become loose under any circumstances (sudden braking, accidents) and

cause injuries to the occupants of the vehicle.

• Secure any parts of the system covered by the bodywork in such a manner that

they cannot be come loose or damage other parts and cables and impair vehicle

functions (steering, pedals, etc.).

• To prevent damage, when drilling ensure that there is sufficient room for the drill

head to come out on the other side (fig. 2, page 4).

• Deburr all drill holes and treat them with a rust-protection agent.

• Always follow the safety instructions of the vehicle manufacturer.

Some work (e.g. on retention systems such as the AIRBAG etc.) may only be

performed by qualified specialists.

CAM50-IO-16S.book Seite 11 Donnerstag, 1. September 2016 3:16 15

EN

Safety and installation instructions CAM50

12

Observe the following instructions when working with electrical parts:

• When testing the voltage in electrical cables, only use a diode test lamp

(fig. 1 8, page 3) or a voltmeter (fig. 1 9, page 3).

Test lamps with an illuminant (fig. 1 12, page 3) take up voltages which are too

high and which can damage the vehicle’s electronic system.

• When making electrical connections, ensure that

– They are not kinked or twisted

– They do not rub on edges

– They are not laid in sharp edged ducts without protection

(see fig. 3, page 4)

• Insulate all connections.

• Secure the cables against mechanical wear with cable binders or insulating tape,

for example to existing cables.

The camera is watertight. However, the sealings on the camera cannot withstand a

high-pressure cleaner (fig. 4, page 4). Therefore, you should observe the following

instructions when handling the camera:

• People (including children) whose physical, sensory or mental capacities or

whose lack of experience or knowledge prevent them from using this product

safely should not use it without the supervision or instruction of a responsible

person.

• Do not open the camera, as this impairs the sealing and the function of the

camera (fig. 5, page 4).

• Do not pull at the cables, as this impairs the sealing and the function of the camera

(fig. 6, page 4).

• The camera is not suitable for submerged operation (fig. 7, page 4).

CAM50-IO-16S.book Seite 12 Donnerstag, 1. September 2016 3:16 15

EN

CAM50 Scope of delivery

13

3Scope of delivery

4Accessories

Available as accessory (not included in scope of delivery):

5 Intended use

The CAM50C and CAM50CW colour cameras are primarily intended for use in

vehicles. They can be used in rear view video systems to observe the space directly

beside or behind the vehicle from the driver’s seat when manoeuvring or parking, for

example.

!

No. in

fig. 8, page 5

Quantity Description Ref. no.

11Camera

2 1 Camera bracket 9102200066

3 1 Camera guard 9102200067

42Side covers

5 1 Extension cable 9102200030

– 1 Fastening material

Description Ref. no.

Extension cable 5 m RV-805 9600000206

Extension cable 10 m RV-810 9600000207

Extension cable 20 m RV-820 9600000208

Spiral cable for trailer operation RV-150-SPK 9600000209

WARNING!

Risk of injury!

Since rear view systems are designed merely as an additional aid for

reversing, it does not relieve you of the duty to take proper care

when reversing.

CAM50-IO-16S.book Seite 13 Donnerstag, 1. September 2016 3:16 15

EN

Technical description CAM50

14

6 Technical description

The camera with integrated microphone, which is encased in aluminium housing,

transmits image and sound to a monitor via a cable. The built-in infrared LEDs

improve night vision.

The camera transmits the image as if you are looking in the rear mirror.

The camera consists of the following main elements:

7 Notes on the electrical connections

7.1 Laying cables

A

Please observe the following instructions:

• As far as possible, use original openings or alternative openings for the

connecting cable duct, e.g. the paneling edges, ventilation grilles or blank

panels. If no openings are available, you must drill holes for the cables. Check

beforehand that there is sufficient room for the drill head to come out on the other

side.

No. in

fig. 9, page 5

Description

1 6-pin connection cable

2 Infrared LEDs

3 Microphone (back side)

NOTICE! Risk of damage!

• To prevent damage, when drilling ensure that there is sufficient

space on the other side for the drill head to come out.

• Cables and connections which are not properly installed will cause

malfunctions or damage to components. Correct installation of

cables and connections is the basic prerequisite for lasting and

trouble-free operation of the retrofitted components.

• The cables may not be exposed for long periods to solvents such as

benzine, as the solvents can damage the cable.

CAM50-IO-16S.book Seite 14 Donnerstag, 1. September 2016 3:16 15

EN

CAM50 Notes on the electrical connections

15

• Wherever possible lay cables inside the vehicle, as they are better protected

inside than outside the vehicle.

If you do need to lay a cable outside the vehicle, ensure that it is well secured

(use additional cable ties, insulating tape, etc.).

• To prevent damage to the cables, when laying them ensure that there is sufficient

distance to hot or moving vehicle components (exhaust pipes, drive shafts, light

systems, fans, heater etc.). Use corrugated piping or other protective materials to

protect against mechanical wear.

• Screw on the plug connections of the connecting cables to protect against water

penetration (fig. h, page 7).

• When laying electric connections, ensure that

– They are not kinked or twisted

– They do not rub on edges

– They are not laid in sharp edged ducts without protection (fig. 3, page 4)

• Attach the cables securely in the vehicles to prevent tripping hazards. Use cable

binders, insulating tape or glue the cables in place.

• Protect every through-hole made in the bodywork against water penetration,

e.g. by using a cable with a sealant and by spraying the cable and the cable

sleeve with sealant.

I

NOTE

Do not start sealing the through-holes until all installation work has been

finished for the camera, and the required cable lengths have been

established.

CAM50-IO-16S.book Seite 15 Donnerstag, 1. September 2016 3:16 15

EN

Mounting the camera CAM50

16

8Mounting the camera

8.1 Tools required

For installation and assembly you will require the following tools:

• Drill bit set (fig. 1 1, page 3)

• Drill (fig. 1 2, page 3)

• Screwdriver (fig. 1 3, page 3)

• Set of ring or open-ended spanners (fig. 1 4, page 3)

• Measuring ruler (fig. 1 5, page 3)

• Hammer (fig. 1 6, page 3)

• Centre punch (fig. 1 7, page 3)

To make and test the electrical connection, the following tools are required:

• Diode test lamp (fig. 1 8, page 3) or voltmeter (fig. 1 9, page 3)

• Insulating tape (fig. 1 11, page 3)

• Cable bushing sleeves, if necessary

To fasten the cables you may require additional cable binders.

8.2 Mounting the camera

!

I

CAUTION!

Select a location for the camera and attach it so securely that it cannot

under any circumstances fall off and injure bystanders (e.g. by being

knocked off by branches brushing over the roof of the vehicle).

NOTE

If installing the camera alters the vehicle height or length specified in the

vehicle documents, your vehicle must be inspected by the appropriate

authorities.

Make sure that you are in possession of documents verifying that your

vehicle has passed this inspection.

CAM50-IO-16S.book Seite 16 Donnerstag, 1. September 2016 3:16 15

EN

CAM50 Mounting the camera

17

Observe the following installation instructions:

• To provide a suitable viewing angle, the camera must be attached at a height of

at least 2 m.

Ensure that you have a firm place from which to work when mounting the camera.

• Ensure that the installation location of the camera is sufficiently firm (e.g. to

prevent the camera from being knocked down by branches that may brush over

the roof of the vehicle).

• Mount the camera bracket horizontally and in the middle of the rear of the vehicle

(fig. 0, page 6).

• The most secure type of attachment is with screws fitted through the body.

Please observe the following instructions:

– There must be sufficient space for the mounting procedure behind the

chosen installation location.

– Suitable measures must be taken to prevent water penetrating through any

holes made (e.g. by using screws and sealant and/or spraying the outer

attachment parts with a sealant).

– The location on the body where you wish to attach the camera must be rigid

enough to allow the camera to be tightly fastened.

• Check beforehand that there is sufficient room for the drill head to come out on

the other side (fig. 2, page 4).

• If you are not sure about the location you have chosen, consult the vehicle

manufacturer or dealer.

I

When mounting the camera, proceed as follows:

➤ Hold the camera on the chosen location and mark at least two different points for

the drill holes (fig. a, page 6).

➤ Using a hammer and centre punch, gently pre-punch the previously marked

points to prevent the drill head from slipping off.

NOTE

We recommend greasing the threads of the bolts to prevent corrosion.

CAM50-IO-16S.book Seite 17 Donnerstag, 1. September 2016 3:16 15

EN

Mounting the camera CAM50

18

If you want to screw on the camera with self-tapping screws

(fig. b, page 6)

A

➤ Drill Ø 2 mm holes at the points you have just marked.

➤ Deburr all drill holes and apply rust-protection.

➤ Screw the camera bracket on with the 3 x 10 mm self-tapping screws.

If you would like to attach the camera with threaded screws fitted through

the construction (fig. c, page 6)

A

➤ Drill Ø 3.5 mm holes at the points you have just marked.

➤ Deburr all drill holes and apply rust-protection.

➤ Screw the camera bracket on with the M3 x 20 mm threaded screws.

Depending on the thickness of the construction, you may require longer

threaded screws.

NOTICE! Risk of damage!

The holder may only be attached to steel panels with a minimum

thickness of 1.5 mm using self-tapping screws.

NOTICE! Risk of damage!

Ensure that that nuts cannot be pulled through the body shell when they

are tightened.

Use larger washers or metal plates if necessary.

CAM50-IO-16S.book Seite 18 Donnerstag, 1. September 2016 3:16 15

EN

CAM50 Mounting the camera

19

Creating a through-hole for the camera connection cable

(fig. d, page 6)

I

A

➤ Drill a hole of Ø 16 mm near the camera.

➤ Deburr all drill holes that have been made in the sheet metal and apply

rust-protection.

➤ Place cable sleeves in all sharp edged ducts.

Mounting the camera

A

➤ Push the camera into the camera bracket.

➤ Attach the camera loosely with the two screws M3 x 6 mm in the slots (fig. e,

page 6).

➤ Align the camera provisorily so that the lens is at an angle of approx. 50° to the

perpendicular axis of the vehicle (fig. f, page 7).

A

➤ Push the camera guard over the camera (fig. g, page 7)

NOTE

If possible, use available openings – such as ventilation grilles – to feed

the connection cables through. If there are no existing openings, you

must drill a hole with a 16 mm diameter.

NOTICE! Risk of damage!

Ensure that there is sufficient space on the other side for the drill head to

come out

NOTICE! Risk of damage!

Only use the screws supplied to mount the camera in the camera

bracket. Longer screws will damage the camera.

NOTICE! Risk of damage!

Never mount the camera without the camera guard.

CAM50-IO-16S.book Seite 19 Donnerstag, 1. September 2016 3:16 15

EN

Mounting the camera CAM50

20

Connecting the camera

I

➤ Guide the camera cable into the vehicle interior.

➤ Insert the plug of the camera cable into the socket of the extension cable.

➤ Screw on the plug connections of the connecting cables to protect against water

penetration (fig. h, page 7).

Aligning the camera

I

➤ Use the monitor image to align the camera:

The monitor image should show the bottom edge of the rear or the bumper of

your vehicle (A). The middle of the bumper should be in the middle of the

screen. (fig. j, page 7).

➤ Check the function of the camera after you have connected it to a monitor.

Fastening the camera

➤ Thighten the two screws in the slots of the camera bracket.

➤ Mount the side covers with the two screws M3 x 8 mm in the middle drill holes

(fig. k, page 8).

NOTE

• Lay the camera cable so that should you need to remove the camera,

you can access the plug connection between the camera and the

extension cable easily. This considerably eases dismantling work.

• To minimise corrosion in the plug, apply a small amount of grease –

such as pin grease – inside the plug.

• Additional extension cables are available on request (see chapter

“Accessories” on page 13).

NOTE

If necessary before aligning the camera connect the camera to a monitor

and to a power supply (see connecting diagram, fig. i, page 7

CAM50-IO-16S.book Seite 20 Donnerstag, 1. September 2016 3:16 15

La page charge ...

Dometic PerfectView CAM50 Mode d'emploi

Ce manuel convient également à

Dometic PerfectView CAM50 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents