Generac PowerPact Series G0069980 Manuel utilisateur

001036

Owner’s Manual

60 Hz Air-Cooled Generators

7.5 kW PowerPact™

SAVE THIS MANUAL FOR FUTURE REFERENCE

Para español , visita: http://www.generac.com/service-support/product-support-lookup

Pour le français, visiter : http://www.generac.com/service-support/product-support-lookup

Register your Generac product at:

WWW.GENERAC.COM

1-888-GENERAC

(888-436-3722)

(000209a)

WARNING

This product is not intended to be used in

a critical life support application. Failure to

adhere to this warning could result in

death or serious injury.

ii Owner’s Manual for 7.5 kW PowerPact™

Use this page to record important information about your generator set.

Record the information found on your unit data label on this

page. For the location of the unit data label, see Safety

Rules & General Information. The unit has a label plate

affixed to the inside partition, to the left of the control panel

console as shown in Figure 2-1. For directions on how to

open the top lid and remove the front panel, see Operation.

When contacting an independent authorized service dealer

about parts and service, always supply the complete model

number and serial number of the unit.

Operation and Maintenance: Proper maintenance and care

of the generator ensures a minimum number of problems

and keeps operating expenses at a minimum. It is the

operator’s responsibility to perform all safety checks, to

make sure that all maintenance for safe operation is

performed promptly. Generac recommends that the

equipment be checked periodically by an Independent

Authorized Service Dealer. Normal maintenance, service

and replacement of parts are the responsibility of the owner/

operator and, as such, are not considered defects in

materials or workmanship within the terms of the warranty.

Individual operating habits and usage may contribute to the

need for additional maintenance or service.

When the generator requires servicing or repairs, Generac

recommends contacting an Independent Authorized Service

Dealer for assistance. Authorized service technicians are

factory-trained and are capable of handling all service

needs.To locate the nearest independent authorized service

dealer, please visit the dealer locator at:

www.generac.com/Service/DealerLocator/.

Model:

Serial:

Prod Date Week:

Volts:

LPV Amps:

NG Amps:

Hz:

Phase:

Controller P/N:

(000005)

WARNING

California Proposition 65. This product contains or

emits chemicals known to the state of California to

cause cancer, birth defects, and other reproductive

harm.

(000004)

WARNING

California Proposition 65. Engine exhaust and some

of its constituents are known to the state of California

to cause cancer, birth defects, and other reproductive

harm.

Table of Contents

Owner’s Manual for 7.5 kW PowerPact™ iii

Section 1: Safety Rules & General

Information

Introduction ..........................................................1

Read This Manual Thoroughly ....................................1

How to Obtain Service .................................................1

Safety Rules .........................................................1

General Hazards .........................................................2

Exhaust Hazards .........................................................3

Electrical Hazards .......................................................3

Fire Hazards ................................................................3

Explosion Hazards ......................................................4

Section 2: General Information

The Generator ......................................................5

Protection Systems .............................................7

Emissions .............................................................7

Fuel Requirements ..............................................7

Battery Requirements .........................................7

Battery Charger ....................................................7

Engine Oil Requirements ....................................7

Section 3: Operation

Site Prep Verification ...........................................9

Controller Lid .......................................................9

Circuit Breaker .....................................................9

Control Panel .....................................................10

Alarm Response Procedures ............................11

Clearing an Alarm/Warning Condition .......................11

Setting the Exercise Timer ................................11

Battery Charger ..................................................11

Manual Transfer Operation ...............................11

Transfer to Generator Power Source ........................11

Transfer Back to Utility Power Source .......................12

Automatic Transfer Operation ..........................12

Automatic Sequence of Operation .................. 13

Utility Failure ..............................................................13

Cranking ....................................................................13

Cold Smart Start ........................................................13

Load Transfer ............................................................13

Shutting Generator Down While Under Load . 13

To turn the generator OFF (while running in AUTO and

online): ......................................................................13

To turn the generator back ON: .................................13

Section 4: Maintenance

Maintenance ....................................................... 15

Performing Scheduled Maintenance ............... 15

Clearing a Maintenance Due Condition ........... 15

Service Schedule ............................................... 16

Checking Engine Oil Level ............................... 18

Engine Oil Recommendations ...................................18

Changing the Oil ................................................ 19

Changing the Engine Air Cleaner .................... 19

Spark Plug .......................................................... 19

Valve Clearance Adjustment ............................ 20

Check Valve Clearance .............................................20

Adjust Valve Clearance .............................................20

Battery Maintenance ......................................... 21

Attention After Submersion ............................. 21

Corrosion Protection ........................................ 21

Remove From, and Return To Service Procedure

22

Remove From Service ...............................................22

Return to Service .......................................................22

Section 5: Troubleshooting

Section 6: Quick Reference Guide

Table of Contents

iv Owner’s Manual for 7.5 kW PowerPact™

This page intentionally left blank.

Safety Rules & General Information

Owner’s Manual for 7.5 kW PowerPact™ 1

Section 1: Safety Rules & General Information

Introduction

Thank you for purchasing this compact, high

performance, air-cooled, engine-driven generator. It is

designed to automatically supply electrical power to

operate critical loads during a utility power failure.

This unit is factory installed in an all-weather, metal

enclosure that is intended exclusively for outdoor

installation. This generator will operate using either vapor

withdrawn liquid propane (LP) or natural gas (NG).

NOTE: When sized properly, this generator is suitable for

supplying typical residential loads such as induction

motors (sump pumps, refrigerators, air conditioners,

furnaces, etc.), electronic components (computer,

monitor, TV, etc.), lighting loads and microwaves.

Read This Manual Thoroughly

If any portion of this manual is not understood, contact

the nearest Independent Authorized Service Dealer for

starting, operating and servicing procedures.

This manual must be used in conjunction with the

appropriate Installation Manual.

SAVE THESE INSTRUCTIONS: The manufacturer

suggests that this manual and the rules for safe operation

be copied and posted near the unit installation site.

Safety should be stressed to all operators and potential

operators of this equipment.

Throughout this publication and on tags and decals

affixed to the generator, DANGER, WARNING, and

CAUTION blocks are used to alert personnel to special

instructions about a particular operation that may be

hazardous if performed incorrectly or carelessly. Observe

them carefully. Their definitions are as follows:

NOTE: Notes provide additional information important to

a procedure or component.

These safety warnings cannot eliminate the hazards they

indicate. Observing safety precautions and strict

compliance with the special instructions while performing

the action or service are essential to preventing accidents.

The operator is responsible for proper and safe use of

the equipment. The manufacturer strongly recommends

that if the operator is also the owner, to read the Owner’s

Manual and thoroughly understand all instructions before

using this equipment. The manufacturer also strongly

recommends instructing other users to properly start and

operate the unit. This prepares them if they need to

operate the equipment in an emergency.

How to Obtain Service

When the generator requires servicing or repairs, Generac

recommends contacting an

Independent Authorized

Service Dealer

(IASD) for assistance. Service technicians

are factory-trained and are capable of handling all service

needs. For assistance locating a dealer, go to

www.generac.com/Service/DealerLocator/.

When contacting an IASD about parts and service, always

supply the complete model number and serial number of

the unit as given on its data decal, which is located on the

generator. Refer to

Figure 2-1

for decal location. Record

the model number and serial numbers in the spaces

provided on the inside front cover of this manual.

Safety Rules

Study these SAFETY RULES carefully before installing,

operating or servicing this equipment. Become familiar

with this Owner’s Manual and with the unit. The

generator can operate safely, efficiently and reliably only

if it is properly installed, operated and maintained. Many

accidents are caused by failing to follow simple and

fundamental rules or precautions.

The manufacturer cannot anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual and on tags and decals affixed to the unit are,

therefore, not all-inclusive. If using a procedure, work

method, or operating technique the manufacturer does not

specifically recommend, verify that it is safe for others.

Also, make sure the procedure, work method or operating

technique utilized does not render the generator unsafe.

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

(000001)

DANGER

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

(000002)

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

(000003)

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Safety Rules & General Information

2 Owner’s Manual for 7.5 kW PowerPact™

General Hazards

Inspect the generator regularly. Generac recommends

contacting the nearest Independent Authorized Service

Dealer for parts needing repair or replacement.

(000190)

DANGER

Loss of life. Property damage. Installation must always

comply with applicable codes, standards, laws and

regulations. Failure to do so will result in death

or serious injury.

Automatic start-up. Disconnect utility power and

render unit inoperable before working on unit.

Failure to do so will result in death or serious injury.

(000191)

DANGER

WARNING

This unit is not intended for use as a prime power

source. It is intended for use as an intermediate power

supply in the event of temporary power outage only.

See individual unit specifications for required

maintenance and run times pertaining to use.

(000247)

(000209a)

WARNING

This product is not intended to be used in

a critical life support application. Failure to

adhere to this warning could result in

death or serious injury.

(000187)

WARNING

(000130)

WARNING

Accidental Start-up. Disconnect the negative battery

cable, then the positive battery cable when working

on unit. Failure to do so could result in death

or serious injury.

(000182)

WARNING

(000155)

WARNING

Only a trained and licensed electrician should perform

wiring and connections to unit. Failure to follow proper

installation requirements could result in death, serious

injury, and damage to equipment or property.

(000115)

WARNING

Moving Parts. Do not wear jewelry when

starting or operating this product. Wearing

jewelry while starting or operating this product

could result in death or serious injury.

(000111)

WARNING

Moving Parts. Keep clothing, hair, and

appendages away from moving parts. Failure

to do so could result in death or serious injury.

(000108)

WARNING

Hot Surfaces. When operating machine, do not

touch hot surfaces. Keep machine away from

combustibles during use. Hot surfaces

could result in severe burns or fire.

(000146)

WARNING

Equipment and property damage. Do not alter

construction of, installation, or block ventilation for

generator. Failure to do so could result in unsafe

operation or damage to the generator.

WARNING

Risk of injury. Do not operate or service this

machine if not fully alert. Fatigue can impair the

ability to service this equipment and could result

in death or serious injury.

(000215)

WARNING

Injury and equipment damage. Do not use

generator as a step. Doing so could result in falling,

damaged parts, unsafe equipment operation,

and could result in death or serious injury.

(000216)

Safety Rules & General Information

Owner’s Manual for 7.5 kW PowerPact™ 3

Exhaust Hazards

•

Adequate, unobstructed flow of cooling and

ventilating air is critical to correct generator

operation. Do not alter the installation or permit

even partial blockage of ventilation provisions, as

this can seriously affect safe operation of the

generator. The generator must be installed and

operated outdoors only.

Electrical Hazards

Fire Hazards

Asphyxiation. Running engines produce

carbon monoxide, a colorless, odorless,

poisonous gas. Carbon monoxide, if not

avoided, will result in death or serious injury.

(000103)

DANGER

(000178a)

Asphyxiation. Always use a battery operated carbon

monoxide alarm indoors and installed according to

the manufacturer’s instructions. Failure to do so

could result in death or serious injury.

WARNING

(000144)

DANGER

Electrocution. Contact with bare wires,

terminals, and connections while generator

is running will result in death or serious injury.

(000150)

DANGER

Electrocution. Never connect this unit to the electrical

system of any building unless a licensed electrician

has installed an approved transfer switch. Failure to

do so will result in death or serious injury.

(000131a)

DANGER

Electrical backfeed. Use only approved switchgear to

isolate generator when electrical utility is the primary

power source. Failure to do so will result in death,

serious injury, and equipment damage.

(000152)

DANGER

Electrocution. Verify electrical system is

properly grounded before applying power.

Failure to do so will result in death or serious

injury.

(000188)

DANGER

Electrocution. Do not wear jewelry while

working on this equipment. Doing so will

result in death or serious injury.

(000104)

DANGER

Electrocution. Water contact with a power

source, if not avoided, will result in death

or serious injury.

(000144)

DANGER

Electrocution. Contact with bare wires,

terminals, and connections while generator

is running will result in death or serious injury.

(000145)

DANGER

Electrocution. In the event of electrical accident,

immediately shut power OFF. Use non-conductive

implements to free victim from live conductor. Apply

first aid and get medical help. Failure to do so will

result in death or serious injury.

WARNING

Fire hazard. Do not obstruct cooling and

ventilating airflow around the generator. Inadequate

ventilation could result in fire hazard, possible

equipment damage, death or serious injury.

(000217)

WARNING

Fire and explosion. Installation must comply

with all local, state, and national electrical

(000218)

building codes. Noncompliance could result in unsafe

operation, equipment damage, death or serious injury.

WARNING

Fire hazard. Use only fully-charged fire

(000219)

extinguishers rated “ABC” by the NFPA. Discharged or

improperly rated fire extinguishers will not extinguish

electrical fires in automatic standby generators.

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

Safety Rules & General Information

4 Owner’s Manual for 7.5 kW PowerPact™

Comply with regulations the Occupational Safety and

Health Administration (OSHA) has established. Also,

verify that the generator is installed in accordance with

the manufacturer’s instructions and recommendations.

Following proper installation, do nothing that might alter a

safe installation and render the unit in noncompliance

with the aforementioned codes, standards, laws and

regulations.

Explosion Hazards

WARNING

required safety equipment could result in

death or serious injury.

(000221)

Risk of electrocution. Refer to NFPA 70E for

safety equipment required when working with

with a live electrical system. Failure to use

(000147)

WARNING

Risk of Fire. Unit must be positioned in a

manner that prevents combustible material

accumulation underneath. Failure to do so

could result in death or serious injury.

(000192)

DANGER

(000151)

DANGER

Connection of fuel source must be done by a qualified

professional technician or contractor. Incorrect installation

of this unit will result in death, serious injury, and damage

to equipment and property damage.

(000174)

DANGER

Risk of fire. Allow fuel spills to completely dry

before starting engine. Failure to do so will

result in death or serious injury.

(000110)

WARNING

Risk of Fire. Hot surfaces could ignite

combustibles, resulting in fire. Fire could

result in death or serious injury.

General Information

Owner’s Manual for 7.5 kW PowerPact™ 5

Section 2: General Information

The Generator

Figure 2-1. GA-420 Engine 7.5 kW Unit

A. Controller Lid F. Control Panel K. Air Box

B. Top Lid G. Data Label L. Spark Plug

C. Customer Connection Box H. Battery Access Panel M. Exhaust Enclosure

D. Front Panel I. Oil Drain Hose N. Alternator

E. Circuit Breaker J. Oil Fill / Dipstick O. Starter Motor

001037

E

A

D

H

G

C

F

B

K

L

M

I

J

N

O

General Information

6 Owner’s Manual for 7.5 kW PowerPact™

Specifications

Generator

Engine

The specification sheet for your generator was included in the documentation provided with the unit at the time of

purchase. For additional copies, consult your local Independent Authorized Service Dealer for your specific generator

model.

Model 7.5 kW

Rated Voltage 240

Rated Maximum Load Current

(Amps) at 220 Volts (LP)*

31.25

Main Circuit Breaker 35 Amp

Phase 1

Rated AC Frequency 60 Hz

Battery Requirement Group U1, 12 Volts and 300 CCA Minimum (see Replacement Parts)

Enclosure Galvanneal Steel

Unit Weight 280 lb (127.3 kg)

Normal Operating Range

This unit is tested in accordance to UL 2200 standards with an operating temperature of -20 ºF (-29

ºC) to 122 ºF (50 ºC). For areas where temperatures fall below 32 ºF (0 ºC) a cold weather kit is

recommended. When operated above 77 ºF (25 ºC) there may be a decrease in engine power.

(Please reference the engine specifications section.)

These generators are rated in accordance with UL 2200, Safety Standard for Stationary Engine Generator Assemblies, and CSA-C22.2 No. 100-04

Standard for Motors and Generators.

* Natural Gas ratings will depend on specific fuel joules/Btu content. Typical derates are between 10-20% off the LP gas rating.

** Circuits to be moved must be protected by same size breaker. For example, a 15 amp circuit in the main panel must be a 15 amp circuit in the

transfer switch.

Model 7.5 kW

Type of Engine GA-420

Number of Cylinders 1

Displacement

25.6 in

3

(420 cc)

Cylinder Block Aluminum w/ cast iron sleeve

Recommended Spark Plug see Replacement Parts

Spark Plug Gap

0.030 in (0.76 mm)

Valve Clearance 0.002 - 0.004 in

(0.05 - 0.1 mm)

Starter 12 VDC

Oil Capacity

Approx. 1.2 qt (1.1 L)

Recommended Air Filter see Replacement Parts

Engine power is subject to and limited by such factors as fuel Btu/joules, ambient temperature and altitude. Engine power decreases about 3.5 percent

for each 1000 feet (304.8 meters) above sea level, and also will decrease about 1 percent for each 10 °F (6 ºC) above 60 ºF (15 ºC) ambient temperature.

General Information

Owner’s Manual for 7.5 kW PowerPact™ 7

Protection Systems

The generator may have to run for long periods of time

with no operator present to monitor the engine/generator

conditions. Therefore, the generator is equipped with a

number of systems to automatically shut down the unit to

protect it against potentially damaging conditions. Some

of these systems are as follows:

The control panel contains LEDs which alert the operator

when a fault condition occurs. The above list is not all

inclusive. For more information about alarms and control

panel operation, see Section 3 Operation.

Emissions

The United States Environmental Protection Agency (US

EPA) (and California Air Resources Board (CARB), for

engines/equipment certified to California standards)

requires that this engine/equipment complies with

exhaust and evaporative emissions standards. Locate

the emissions compliance decal on the engine to

determine applicable standards. For emissions warranty

information, please reference the included emissions

warranty. It is important to follow the maintenance

specifications in the manual to ensure that the engine

complies with the applicable emissions standards for the

duration of the product’s life.

This generator is certified to operate on Liquid Propane

Vapor fuel or pipeline Natural Gas.

The Emission Control System code is EM (Engine

Modification). The Emission Control System on this

generator consists of the following:

Fuel Requirements

The engine has been fitted with a dual fuel carburetion

system. The unit will run on natural gas or LP gas

(vapor), but it has been factory set to run on natural gas.

The fuel system will be configured for the available fuel

source during installation.

Recommended fuels should have a BTU content of at

least 1000 BTUs per cubic foot (37.26 megajoules per

cubic meter) for natural gas, or at least 2500 BTUs per

cubic foot (93.15 megajoules per cubic meter) for LP gas

(vapor).

NOTE: If converting to LP gas from natural gas, a

minimum LP tank size of 250 gallons (946 liters) is

recommended. See the Installation Manual for complete

procedures and details.

Battery Requirements

Group U1, 12V, minimum 300 CCA.

For proper battery maintenance procedures, see Section

4 Maintenance.

Battery Charger

The battery charger is integrated into the control panel

module in all models. It operates as a Smart Charger

which ensures output charging levels are safe and

continuously optimized to promote maximum battery life.

Engine Oil Requirements

For proper oil viscosity, see chart in Figure 4-2.

•Low Oil Level Sensor

•High Temperature

Sensor

•Overcrank Detection

•Overspeed Detection

•RPM Sensor

•Underspeed Detection

•Charger Problem

Detection

•Battery Problem

Detection

•Fuse Problem Detection

(missing or failed)

•Wiring Error Detection

System Components

Air Induction

- Airbox Assembly

- Air Cleaner

Fuel Metering

- Carburetor / Mixer Assembly

- Fuel Regulator

- Fuel Jet

Ignition

- Spark Plug

- Ignition Module

Exhaust

- Exhaust Manifold

- Muffler

- Muffler System

(000105)

DANGER

Explosion and Fire. Fuel and vapors are

extremely flammable and explosive. Add fuel

in a well ventilated area. Keep fire and spark

away. Failure to do so will result in death

or serious injury.

General Information

8 Owner’s Manual for 7.5 kW PowerPact™

Replacement Parts

Accessories

Performance enhancing accessories are available for air-cooled generators.

NOTE: Contact an Independent Authorized Service Dealer or visit www.generac.com for additional information on

replacement parts, accessories, and extended warranties.

Description 7.5 kW

U1 Exide Battery 0J5584

Spark Plug 0L3059

Air Filter 0E9371A

Control Panel Fuse (7.5 Amp) 0D7178T

Transfer Switch Fuses (5 Amp) 073590A

Accessory Description

Cold Weather Kit Recommended in areas where temperatures fall below 32 ºF (0 ºC).

Scheduled Maintenance Kit Includes all pieces necessary to perform maintenance on the generator along

with oil recommendations.

Mobile Link™ (USA only)

006463-0

Provides a personalized web portal that displays the generator status,

maintenance schedule, event history and much more. This portal is accessible

via computer, tablet or smart phone. Sends emails and/or text notifications the

moment there is any change in the generator’s status. Notification settings can

be customized to what type of alert is sent and how often. For more

information, visit www.MobileLinkGen.com.

Touch-Up Paint Kit Very important to maintain the look and integrity of the generator enclosure.

This kit includes touch-up paint and instructions.

Wireless Local Monitor

006664-0

Completely wireless and battery powered, the Wireless Local Monitor provides

you with instant status without ever leaving the house. Status lights (red, yellow

and green) alert owners when the generator needs attention. Magnetic backing

permits refrigerator mounting and gives a 600 feet (183 meters) line of sight

communication.

Extended Warranty Coverage

(Available only in the U.S. and

Canada)

Extend your generator warranty coverage by purchasing extended warranty

coverage. Covers both parts and labor. Extended coverage can be purchased

within 12 months of the end-users purchase date.

This extended coverage is applicable to registered units and end-user proof of

purchase must be available upon request.

Available for Generac

®

, Guardian

®

, Centurion

®

, and Synergy™ products. Not

available for EcoGen™ products or all international purchases.

Operation

Owner’s Manual for 7.5 kW PowerPact™ 9

Section 3: Operation

Site Prep Verification

It is important that the generator is installed in such a way

that the airflow into and out of the generator is not

impeded. Verify that all shrubs or tall grasses have been

removed within 3 ft (0.91 m) of the intake and discharge

louvers on the sides of the enclosure. It is also important

that the generator is not subject to water intrusion. Verify

that all potential sources such as water sprinklers, roof

run-off, rain gutter down spouts and sump pump

discharges are directed away from the generator

enclosure.

Turn the generator OFF before performing maintenance.

Remove 7.5 Amp fuse, T1 battery charge fuse, and

disconnect battery cables to prevent accidental start up.

Disconnect the NEGATIVE (–) cable first, then

disconnect the POSITIVE (+) cable. When connecting

the cables, connect the POSITIVE cable first, the

NEGATIVE cable last.

Controller Lid

To open or close the controller lid:

1. See view “A” in Figure 3-1. Lift lid from bottom to

open. Lid will lock in place when raised.

2. See view “B” in Figure 3-1. Pull raised lid up and

out sightly to unlock, then lower to close.

Figure 3-1. Open and Close Controller Lid

NOTE: Local codes may require this compartment to be

locked. A hasp is provided so the owner/operator can

secure the compartment with a padlock (C in Figure 3-1).

Check local codes for side compartment locking

requirements.

NOTE: All appropriate panels must be in place during

any operation of the generator. This includes operation

by a servicing technician while conducting

troubleshooting procedures.

Circuit Breaker

The Main Line Circuit Breaker (MLCB) is located under

the Controller Lid. Open the Controller Lid to access the

circuit breaker (A in Figure 3-2).

Figure 3-2. Control Panel and Circuit Breaker

Risk of fire. Keep air inlet and exhaust areas

WARNING

(000251)

free from leaves, grass, snow and other debris.

Failure to do so could result in death, serious injury,

property, and equipment damage.

Automatic start-up. Disconnect utility power and

render unit inoperable before working on unit.

Failure to do so will result in death or serious injury.

(000191)

DANGER

(000182)

WARNING

001705

A

B

C

001039

A

B

Operation

10 Owner’s Manual for 7.5 kW PowerPact™

Control Panel

The Control Panel is located under the Controller Lid.

Open the Controller Lid to access the control panel (B in

Figure 3-2).

The Auto/Off/Manual Interface located on the Control

Panel has the following features (see Figure 3-3):

• Alarm LEDs (A)

• Warning LEDs (B)

• Operation Mode Buttons and LEDs (C)

Figure 3-3. Generator Control Panel and LEDs

Using the Auto/Off/Manual Interface

NOTE: Loss of utility power will cause either the AUTO or OFF or MANUAL button to flash depending on which mode

the generator is in at the time of utility loss.

Using the LED Interface

The user interface includes seven (7) LEDs to indicate

generator alarms, warnings, and maintenance actions

due. See Figure 3-3 and the following table for details on

each indication.

The user interface also includes 3-mode LEDs to indicate

the current generator mode setting (AUTO, MANUAL, or

OFF). The active LED is also used to indicate whether

the utility voltage is present. The active LED will be solid

when utility is available. It will flash to indicate the loss of

utility power. For example; when the generator is in

AUTO and Utility is present, the green AUTO LED will be

solid ON. When the generator is in AUTO and utility is

lost, the AUTO LED will flash.

001052

A

B

C

Button Description of Operation

AUTO (GREEN)

Selecting this button activates fully automatic system operation. It also allows the unit to automatically

start and exercise the engine every seven days with the setting of the exercise timer (see

Setting

the Exercise Timer

).

MANUAL (BLUE)

This button will crank and start the generator. Transfer to standby power will not occur unless there is

a utility failure.

OFF (RED) This button shuts down the engine and also prevents automatic operation of the unit.

SET EXERCISE (GREY)

Used to establish generator exercise time. Hold the button for 3 seconds at the new exercise time

desired. NOTE: Exercise time can only be set at the time you wish exercise to actually take place.

LED Alarm Description (LED Flashing) Description (LED Solid)

Temperature Alarm (Flashing)

Low Oil Level Alarm (Solid) *

Temperature levels are excessive

—

Engine oil level is insufficient

Charger Warning (Flashing)

Battery Problem Warning (Solid) *

Charging problem exists

—

Battery problem exists

RPM Sensor Alarm — RPM sensor problem exists

Overcrank Alarm — Overcranking condition exists

Speed Alarm * Overspeed condition exists Underspeed condition exists

Break-in Maintenance Due (Flashing)

Regular Maintenance Due (Solid) *

20 hour break-in maintenance due

—

1 year / 100 hour maintenance due

* These LEDs are shared with two alarm conditions. Solid light indicates one alarm. Flashing light indicates the other alarm

condition.

Operation

Owner’s Manual for 7.5 kW PowerPact™ 11

Alarm Response Procedures

The generator is protected by a series of sensors that will

detect an Alarm/Warning condition and alert the owner/

operator of the condition via the Control Panel display.

When certain alarm conditions are detected, the

generator will shut down.

NOTE: Unless properly trained to clear and correct

Warning and Alarm conditions, contact the nearest

Independent Authorized Service Dealer or Trained

Technician.

Clearing an Alarm/Warning Condition

To clear an alarm or warning condition from the Control

Panel, press the OFF button. Press OFF button again.

The flashing or solid indicator LED will turn off.

NOTE: Clearing a code will not correct the problem. It

will simply turn off the LED indicating that told you that a

problem occurred. The problem indicated must be

diagnosed and corrected to prevent a re-occurring alarm

condition.

NOTE: Removing or failure of the 7.5 Amp ATO

®

fuse

will turn off all the panel LEDs. Replacement of the fuse

will initiate the LED self test.

Setting the Exercise Timer

This generator is equipped with an exercise timer. Once it

is set, the generator will start and exercise every seven

days, on the day of the week and at the time of day this

procedure was initiated. During this exercise period, the

unit runs for approximately 12 minutes and then shuts

down. Transfer of loads to the generator output does not

occur during the exercise cycle unless utility power is lost

.

1. Place the generator in the AUTO mode.

2. Hold the SET EXERCISE Button for 3 seconds.

The generator will start, run an exercise cycle and

confirm the setting.

3. The exercise time is now established. The

generator will exercise each week at this time.

To CHANGE the exercise time once it has been set, hold

the SET EXERCISE button on the generator for three (3)

seconds at the time you wish the new exercise time to

take place. The exercise timer does not correct for

daylight savings time.

NOTE: The exerciser will only work in the AUTO mode

and will default to exercise weekly at the time the Control

Panel was last powered ON unless this procedure is

performed. The exercise function will need to be reset

every time the 12 volt battery and T1 power to the

generator are disconnected and then reconnected, or

when the fuse is removed and T1 power is removed from

the generator, or both.

NOTE: If the unit is equipped with Mobile Link™, the

exercise time can be remotely set for any desired day or

time.

Battery Charger

NOTE: The battery charger is integrated into the control

panel.

The battery charger operates as a Smart Charger that:

• verifies output is continually optimized to promote

maximum battery life.

• verifies that charging levels are safe.

NOTE: Battery Problem LED is illuminated when the

battery needs service.

Manual Transfer Operation

Prior to automatic operation, manually exercise the

transfer switch to verify that there is no interference with

proper operation of the mechanism. Manual operation of

the transfer switch is required if electronic operation

should fail.

Transfer to Generator Power Source

1. Verify generator is in the OFF mode.

2. Set the main circuit breaker (Generator

Disconnect) to OFF or OPEN.

3. Turn off the utility power supply to the transfer

switch using the means provided (such as a utility

main line circuit breaker).

4. Use the manual transfer handle (A in Figure 3-4)

inside the transfer switch to move the main

contacts to the STANDBY position (loads

connected to the standby power source, B in

Figure 3-4).

LED

Condition

Action

2nd

Action

3rd

Action

Clear Alarm /

Warning or

Maintenance

LED Alarm(s)

press OFF

again

—

Clear

Maintenance

LED when

Alarm or

Warning LED is

also present

press OFF

again

press OFF

3rd time

(000132)

DANGER

Electrocution. Do not manually transfer under load.

Disconnect transfer switch from all power sources

prior to manual transfer. Failure to do so will result

in death or serious injury, and equipment damage.

Operation

12 Owner’s Manual for 7.5 kW PowerPact™

5. To crank and start the engine, press the control

panel MANUAL button.

6. Allow the engine to stabilize and warm up for a few

minutes.

7. Set the main circuit breaker (Generator

Disconnect) to ON or CLOSED. The standby

power source now powers the loads.

Figure 3-4. Manual Transfer Switch Operation

IMPORTANT NOTE: Actual switch operation may vary. Follow directions in the appropriate transfer switch manual.

Transfer Back to Utility Power Source

When utility power has been restored, transfer back to

utility source and shut down the generator. To manually

transfer back to utility power and shut down the

generator:

1. Set the Main Circuit Breaker (Generator

Disconnect) to OFF or OPEN.

2. Allow the engine to run for 2 minutes at no-load to

stabilize the internal temperatures.

3. Press the control panel OFF button. The engine

should shut down.

4. Verify that utility power supply to the transfer switch

is turned off.

5. Use the manual transfer handle inside the transfer

switch to move the main contacts back to the

UTILITY position (loads connected to the utility

power source, A in Figure 3-4).

6. Turn on the utility power supply to the transfer

switch using the means provided.

7. Press the control panel AUTO button.

Automatic Transfer Operation

To select automatic operation:

1. Make sure the transfer switch main contacts are

set to the UTILITY position (loads connected to the

utility power source).

2.

Verify that normal UTILITY power source voltage is

available to transfer switch terminal lugs N1 and N2.

3. Press the AUTO button on the control panel

interface.

4. Set the main circuit breaker (Generator

Disconnect) to the ON (Closed) position.

With these steps complete, the generator will start

automatically when utility source voltage drops below a

preset level. After the unit starts, loads are transferred to

the standby power source.

000947

A

B

MANUAL

• Will not transfer to generator if utility is present.

• Will transfer to generator if utility fails (below 65% of nominal for 10 consecutive seconds).

• Will transfer back when utility returns for 15 consecutive seconds. The engine will continue to

run until removed from the MANUAL mode.

AUTO

• Will start and run if utility fails (below 65% of nominal for 5 consecutive seconds).

• Will start a 6 second engine warm-up timer (or 30 seconds; refer to Cold Smart Start).

–Will not transfer if utility subsequently returns.

–Will transfer to generator if utility is not present.

• Will transfer back to utility once utility returns (above 80% of nominal) for 15 seconds.

• Will not transfer back to utility unless utility returns. The generator will shut down if the OFF

button is pressed or a shutdown alarm is present.

• Once utility power is returned, the generator will shut down after 1 minute cool-down time.

EXERCISE

• Will not exercise if generator is already running in either AUTO or MANUAL mode.

• During exercise, the control panel will only transfer if utility fails during exercise for 6 seconds

(or 30 seconds; refer to

Cold Smart Start) and will operate as normal in AUTO mode.

Operation

Owner’s Manual for 7.5 kW PowerPact™ 13

Automatic Sequence of Operation

Utility Failure

With the generator set to AUTO, when utility fails (below

65% of nominal) a 5 second line interrupt delay time is

started. If utility is still gone when the timer expires, the

engine will crank and start. Once started, a 6 second

engine warm-up timer will be initiated

(or a 30 second

warm-up timer; refer to

Cold Smart Start). When the warm-

up time expires, the control panel will transfer the load to

the generator. If the utility power is restored (above 80%

nominal) at any time from the initiation of the engine start

until the generator is ready to accept load (warm-up time

has not elapsed), the control panel will complete the start

cycle and run the generator through its normal cool down

cycle, however, the load will remain on the utility source.

Cranking

The system will control the cyclic cranking as follows:

• 5 cranking cycles as follows: 16 second crank,

seven (7) second rest, 16 second crank, seven (7)

second rest, followed by three (3) additional cycles

of seven (7) second cranks followed by seven (7)

second rests.

Cold Smart Start

The Cold Smart Start feature enables the generator to

monitor ambient temperature. The warm-up delay will be

adjusted based on prevailing conditions.

On a startup in AUTO mode, if the ambient temperature is

below a fixed temperature (based on model) the generator

will warm up for 30 seconds. This allows the engine to

warm before a load is applied. If the ambient temperature

is at or above the fixed temperature, the generator will

start up with the normal warm-up delay of 6 seconds.

Load Transfer

The transfer of load when the generator is running is

dependent upon the operating mode.

Shutting Generator Down While

Under Load

IMPORTANT NOTE: To turn the generator off during

utility outages to perform maintenance, or conserve fuel,

follow these steps:

To turn the generator OFF (while running in

AUTO and online):

1. Turn the main utility disconnect OFF.

2. Turn the main line circuit breaker (MLCB) on the

generator to OFF (OPEN).

3. Turn the generator OFF.

To turn the generator back ON:

1. Put the generator back into AUTO and allow to

start and warm-up for a few minutes.

2. Set the MLCB on the generator to ON.

The system will now be operating in automatic mode.

The main utility disconnect can be turned ON (CLOSED).

To shut the unit OFF, this complete process must be

repeated.

Operation

14 Owner’s Manual for 7.5 kW PowerPact™

This page intentionally left blank.

Maintenance

Owner’s Manual for 7.5 kW PowerPact™ 15

Section 4: Maintenance

Maintenance

Regular maintenance will improve performance and

extend engine/equipment life. Generac Power Systems,

Inc. recommends that all maintenance work be

performed by an Independent Authorized Service Dealer

(IASD). Regular maintenance, replacement or repair of

the emissions control devices and systems may be

performed by any repair shop or person of the owner’s

choosing. However, to obtain emissions control warranty

service free of charge, the work must be performed by an

IASD. See the emissions warranty.

Performing Scheduled

Maintenance

It is important to perform maintenance as specified in the

Service Schedule for proper generator operation and to

verify that the generator complies with the applicable

emission standards for the duration of its useful life.

Service and repairs may be performed by any qualified

service person or repair shop.

Additionally, emissions-critical maintenance must be

performed as scheduled in order for the Emissions

Warranty to be valid. Emissions-critical maintenance

consists of servicing the air filter and spark plugs in

accordance with the Service Schedule. The Control

Panel will prompt for break-in or regular maintenance,

when it is required, to be performed. Break-in

maintenance consists of the oil change, valve clearance

and tune-up. Regular maintenance includes the oil, tune-

up, air cleaner, spark plug and valve clearance.

NOTE: The control panel Maintenance Due light will

flash when the initial 20 hour break-in interval has been

reached. The same light will be lit solid when following

regular maintenance intervals are required (every 1 year/

100 hours).

Clearing a Maintenance Due

Condition

After performing maintenance, the Maintenance Due light

must be cleared. To reset the Maintenance Due light, the

generator must be in OFF mode. Set the Generator to

OFF and press the OFF button to reset Maintenance

Due. If an alarm condition exists, the alarm condition

must be cleared prior to resetting the Maintenance Due

light.

(000182)

WARNING

Maintenance

16 Owner’s Manual for 7.5 kW PowerPact™

Service Schedule

NOTE: Contact an Independent Authorized Service Dealer or visit www.generac.com for additional information on

replacement parts.

Table 4-1. Service Maintenance Schedule

System Component Procedure Frequency

X = Action

* = Notify dealer if repair is needed Inspect Change Clean

W = Weekly

M = Monthly

Y = Yearly

Fuel

Fuel lines and connections X M

Lubrication

Oil level X M or 24 hours of continuous operation

Oil X 6 M or 100 hours of operation **

Enclosure louvers X X W

Battery

Remove corrosion; ensure dryness X X Y

Clean and tighten battery terminals X X Y

Check charge state X X Y

Electrolyte level (unsealed batteries only)* X X Every 6 M

Engine and mounting

Air cleaner

XXX

3 M / 50 hours - clean

1 Y / 300 hours - replace

Spark plug

XX

6 M or 100 hours - inspect

1 Y or 300 hours - change

Valve clearance X 1 Y or 300 hours***

General condition

Vibration, noise, leakage * X M

Contact the nearest Independent Authorized Service Dealer for assistance if necessary.

* Contact the nearest Independent Authorized Service Dealer for assistance if necessary.

** Change oil after the first 20 hours of operation or 1 month. Continue to check at intervals of 100 hours or 6 months, whichever occurs first. Severe duty oil drain

intervals: In cold weather conditions (ambient below 40 ºF [4.4 ºC]) change engine oil every 6 months or 50 hours of operation to prevent accumulation of water in

the oil. If the unit will be operated continuously in hot ambient conditions (ambient above 85 ºF [29.4 ºC]) or operation in an extremely dusty or dirty environment

change the engine oil every 3 months or 50 hours of operation to prevent oil breakdown.

*** Check valve clearance after the first 20 hours of operation. Continue to check at intervals of 300 hours.

La page charge ...

Generac PowerPact Series G0069980 Manuel utilisateur

Generac PowerPact Series G0069980 Manuel utilisateur

dans d''autres langues

Documents connexes