Hestan KWD30 Manuel utilisateur

INDOOR COOKING

Warming Drawer

KWD

Use and Care Manual

Installation Instructions

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING

PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of

this or any other appliance.

Installation and service must be performed by a qualified installer or service agency.

DO NOT REPAIR, REPLACE OR REMOVE ANY PART OF THE APPLIANCE UNLESS

SPECIFICALLY RECOMMENDED IN THE MANUALS. IMPROPER INSTALLATION,

SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER

TO THIS MANUAL FOR GUIDANCE. ALL OTHER SERVICING SHOULD BE DONE BY A

HESTAN AUTHORIZED SERVICE TECHNICIAN.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY

BEFORE INSTALLING OR USING YOUR APPLIANCE TO REDUCE

THE RISK OF FIRE, BURN HAZARD, OR OTHER INJURY. KEEP

THIS MANUAL FOR FUTURE REFERENCE.

SAFETY DEFINITIONS

THIS INDICATES THAT DEATH OR SERIOUS INJURY MAY OCCUR

AS A RESULT OF NOT OBSERVING THIS WARNING

THIS INDICATES THAT MINOR OR MODERATE INJURY MAY

OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.

THIS INDICATES THAT DAMAGE TO THE APPLIANCE OR

PROPERTY MAY OCCUR AS A RESULT OF NOT OBSERVING THIS

WARNING.

CAUTION

NOTICE

INSTALLER: LEAVE THIS MANUAL WITH THE OWNER OF THE APPLIANCE.

HOMEOWNER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

Message from Hestan:

Hestan’s award-winning culinary innovations and purpose-built features

reinvented the restaurant kitchen and redefined culinary experience in

some of America’s most acclaimed restaurants. Hestan now takes this

performance from the back of the house and puts it front and center in

yours. Thoughtfully designed and meticulously built, Hestan will serve you

beautifully for years to come.

Hestan is the only residential brand born from the dreams and demands of

professional chefs. From ranges to refrigeration, every detail is designed

to deliver the performance and reliability expected in a restaurant – now

available for you.

We appreciate you choosing Hestan, and we promise to deliver the very best

to you.

Welcome to Hestan

1

EN

ELECTRICAL SHOCK HAZARD

Disconnect power before installing or servicing appliance. Be sure the

knob is in the OFF position before plugging the appliance in.

Failure to do so can result in death or electrical shock.

ELECTRICAL GROUNDING

• This appliance must be grounded. Grounding reduces the risk of

electric shock in the event of a short circuit.

ELECTRICAL SUPPLY

This appliance is designed to use a grounded receptacle, 120 VAC Single Phase, 60 Hz, with a

current rating as shown in the model number listing on page 6.

Have the installer show you where the electric circuit breaker is located so you know how to

shut off the power to this appliance.

TABLE OF CONTENTS

3 SAFETY PRECAUTIONS - BEFORE YOU BEGIN

6 MODEL NUMBERS

6 RATING LABEL

6 REGULATORY / CODE REQUIREMENTS

7 USING THE WARMING DRAWER

11 CLEANING AND MAINTENANCE

14 TROUBLESHOOTING

15 INSTALLATION

20 PARTS / SERVICE

20 LIMITED WARRANTY

When properly cared for, your Hestan appliance will provide safe, reliable service for many years.

When using this appliance, basic safety practices must be followed as outlined below.

IMPORTANT: Save these instructions for the local Utility Inspector’s use.

INSTALLER: Please leave these Installation Instructions with the owner.

OWNER: Please retain these Installation Instructions for future reference.

This oven is NOT designed for installation in manufactured (mobile) homes or recreational park

trailers. Do NOT install this oven outdoors.

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

3

EN

GENERAL APPLIANCE SAFETY PRECAUTIONS

Please read all instructions before using this appliance.

When properly cared for, your new Warming Drawer has been designed to be a safe, reliable

appliance. Read all instructions carefully before using this it. These precautions will reduce the

risk of burns, electric shock, fire, and injury to persons. When using kitchen appliances, basic

safety precautions must be followed, including the following:

TECHNICAL SAFETY

Do not repair or replace any part of the warming drawer unless specifically recommended. Refer

service to an authorized servicer.

Do not operate this appliance if it is not working properly or if it has been damaged, until an

authorized servicer has examined it.

Install or locate this appliance only in accordance with the Installation Instructions. Do not

cover or block any openings on this appliance.

Use this warming drawer only as described in this manual. If you have any questions, contact

Hestan Customer care.

Use this appliance only for its intended use as described in this manual. Do not use corrosive

chemicals, vapors, or nonfood products in this appliance. This type of warming drawer is

specifically designed to heat or cook. It is not designed for industrial or laboratory use. The use

of corrosive chemicals in heating or cleaning will damage the appliance.

CHILD SAFETY

CAUTION

IT IS THE RESPONSIBILITY OF THE PARENTS OR GUARDIANS TO ENSURE CHILDREN

ARE INSTRUCTED IN THE SAFE USE OF THIS APPLIANCE. Do not allow children to use this

appliance without adult supervision. Do not allow children to play in or around the appliance,

even when not in use. Items of interest to children should not be stored in or on the appliance

or in cabinets above the appliance. Children climbing on the appliance could be seriously

injured.

FOOD SAFETY

If food will be held for more than one hour, it must be held at 140°F [60°C] or above. (MED)

GENERAL SAFETY

When using electrical appliances, basic safety precautions should always be followed including

the following:

• Do not touch hot surfaces. Use handles or knobs.

• To protect against electrical shock do not immerse cord or plug in water or other liquid.

• Close supervision is necessary when any appliance is used by or near children.

• Unplug from outlet or turn breaker off before cleaning. Allow to cool before removing or

replacing parts.

• Do not operate any appliance with a damaged cord or plug or after the appliance

malfunctions or has been damaged in any manner. Return appliance to the nearest

authorized service facility for examination, repair, or adjustment.

• The use of accessory attachments not recommended by Hestan may cause injuries.

• Do not use outdoors.

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

(CONT.)

4

EN

• Do not let cord hang over edge of table or counter, or touch hot surfaces.

• Extreme caution must be used when moving anything containing hot oil or other hot

liquids.

• Always turn the knob to OFF, then plug cord into the wall outlet. To disconnect, turn the

knob to OFF, then remove plug from wall outlet.

• Do not use appliance for other than intended use.

• The inside of the appliance can reach temperatures of 195°F [90°C] depending on the

selected temperature and the time of operation. If necessary use gloves to remove things

from the drawer.

• Do not lean or sit on the warming drawer when opened, this could cause damage to the

telescopic guide. The maximum carrying weight of the warming drawer is 80 lbs. (36 kg).

• Do not keep plastic containers or any flammable objects in the appliance. Such objects pose

a risk of catching fire once the warming drawer is turned on.

• In the event that personal clothing or hair catches fire, DROP AND ROLL IMMEDIATELY to

extinguish flames.

Save these Instructions.

SAFETY DURING CLEANING

Never use a vacuum cleaner. The vacuum could create pressure on the components causing a

short circuit. The vacuum may also damage the surface and the components of the appliance:

damages for which Hestan will not be liable.

Follow suggestions listed under “Cleaning and Maintenance” in this manual.

Never use sharp metal objects or abrasive scrubbing pads, as they can damage the surface of the

appliance. If necessary, use standard non-abrasive utensils made of wood or plastic.

REPAIRS:

Maintenance work and/or repairs must be performed exclusively by qualified personnel.

Incorrect installation and maintenance can cause personal injury to the consumer for which

Hestan will not be liable.

During the warranty period, the appliance may only be serviced by technicians authorized by

Hestan or the warranty will be void.

Before beginning maintenance, installation, or repair work disconnect the appliance from the

electrical outlet. The appliance is disconnected only if either:

1. The circuit is turned off (Breaker OFF or the electrical fuse is removed), OR

2. The cord of the appliance is removed from the electrical outlet.

Hestan will not be liable for damage caused by a failure to follow current regulations or the use

of non-original replacement parts.

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

(CONT.)

5

EN

RATING LABEL

The rating label contains important information about your Hestan appliance such as the

model and serial number, electrical rating and the minimum installation clearances.

The rating label is located on the bottom of the drawer.

If service is necessary, contact Hestan Customer Care with the model and serial number

information shown on the label.

MODEL NUMBERS

MODEL NO. DESCRIPTION

CIRCUIT BREAKER

REQ’D

KWD 30 30” Warming Drawer 15 Amp

KDO30

HESTAN COMMERCIAL CORP.

ANAHEIM, CA - USA

TYPICAL RATING LABEL

REGULATORY / CODE REQUIREMENTS

Installation of this cooking appliance must be made in accordance with local codes. In the

absence of local codes, this unit should be installed in accordance with the National Electrical

Code and local codes.

This appliance must be electrically grounded in accordance with local codes or in the absence

of local codes with the National Electrical Code

ANSI/NFPA 70

, or Canadian Electrical code

CSA C22.1

.

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

(CONT.)

6

EN

OPENING THE PUSH-TO-OPEN DRAWER

To open the drawer, press the front of the drawer and release it.

It will open a short distance. Grasp the drawer pull it towards you until it is opened completely.

CLOSING THE DRAWER

To close the drawer, gently push the drawer back, pushing the front until it has completely gone

back.

OPENING THE SOFT CLOSING DRAWER

To open the drawer grasp the handle and pull the drawer.

CLOSING THE DRAWER

To close the drawer, gently push the drawer back, until the soft closing system engage.

BEFORE YOU BEGIN

Before using the appliance for the first time:

1. Gently clean it with a moist cloth and dry it completely as described under “Cleaning and

Maintenance”.

2. Set the control knob to MAX, and let the warming drawer warm for at least two hours. Be

sure that the kitchen is kept well ventilated during the heating period.

• The metal parts have been specially treated with a protective coating that can sometimes

cause odors the first time the drawer is heated. These odors will quickly dissipate and

should not be considered a defect of the appliance.

HEATING SYSTEM

The appliance is equipped with a hot air ventilating system. A fan distributes heat in the

warming drawer to obtain a uniform temperature.

• The thermostat allows the user to control and set the appliance at the desired temperature.

• The circulation of the air heats the drawer in a rapid and uniform way.

• With the protective measures in place it is not possible to accidentally touch the heating

element or the fan.

USING THE WARMING DRAWER

7

EN

CONTROLS AND INDICATORS

A single knob (Mode Selector) controls the warming drawer.

It has positions for OFF, Proofing, and Defrost, plus a continuous range from WARM to MAX.

This manual will use MED to designate a setting halfway between WARM and MAX.

The interior lights come on when the drawer is opened.

The panel indicator light comes on when the knob is in warming mode. (From WARM to MAX.)

OPERATION

Open the drawer. Turn the knob to set the desired function or temperature.

To turn off the appliance, turn the knob to the OFF position.

HEATING TIME

The warming time is influenced by:

• Amount of dishes or food in the drawer

• The arrangement of items in the drawer

• The temperate set.

In general, the more dishes or items in the drawer and the higher the set temperature, the longer

it will take to reach the set temperature.

DISH WARMING

• Dishes for 6 persons, set temperature to MIN or greater.

• Warming time 30-35 minutes

With experience you will learn the optimal temperature setting for your needs.

DEFROSTING

The defrosting function only uses forced ventilation without any active heating element.

Procedure

• Place items to defrosted, turn the knob to the defrost setting.

Mode Selector Function

Off

Proofing

Defrost

Warming

77-95°F [25-35°C]

Fan, no heat

105 - 195°F [40-90°C]

WARM > MAX

None

USING THE WARMING DRAWER

(CONT.)

8

EN

PROOFING

The proofing function maintains the drawer temperature between 77 and 95°F [25-35°C].

Procedure

1. Preheat the drawer for 5 minutes by turning the knob to proofing.

2. Place the dough, wrapped in a slightly damp cloth, in the middle of the drawer.

FOOD WARMING

Food recommended for warming: meat, chicken, fish, sauces, vegetables, side dishes and soups.

• To avoid spills, do not overfill the dishes.

• Arrange the dishes in the drawer and close it carefully so that any liquids do not spill.

• It is advisable not to warm food for more than an hour to prevent it from losing nutritional

value.

• If food will be held for more than one hour, it must be held at 140°F [60°C] or above. (MED)

Cover moist food and liquids with a lid or heat-resistant cling film. This will prevent the

moisture from escaping, condensation from forming and moisture settling on the outside the

dishes.

Do not cover roast or fried dishes which need to stay crisp. Keep these dishes hot at high

temperatures.

PROCEDURE

1. Place the dishes in the drawer.

2. Switch the drawer turning the thermostat knob to between MIN/MED (105/140°F -

40/60°C), depending on the temperature required, and preheat the drawer for 10 minutes.

3. Put the food in the preheated dishes.

4. Close the drawer again.

SWITCHING OFF

Turn the knob to OFF. Take the dishes out of the drawer using a cloth or oven gloves.

NOTE: Never transfer hot dishes directly from the hot stove top to the glass base of the heating

drawer. This could damage the glass drawer base.

SLOW COOKING

Slow cooking is ideal for cooking tender meat which needs to be medium rare or rare. This

cooking method means the meat will always be pink inside. This does not, however, mean that

the meat is raw or undercooked.

• This cooking method not only keeps the juices inside, but it also makes it easy to keep the

meat hot.

• Suitable dishes to use: glass, porcelain or ceramic with a lid.

PROCEDURE

1. Preheat the warming drawer with the chosen dish to the maximum temperature for 15

minutes.

2. Heat some butter or oil in a pan. Brown the meat well for the time indicated in the table,

then place it immediately in the preheated pan and cover with the lid.

3. Set the thermostat between MED/MAX (140/195°F ) [60/90°C] for the time required to

finish the cooking.

USING THE WARMING DRAWER

(CONT.)

9

EN

WARNINGS FOR SLOW COOKING

Only use fresh meat in perfect condition.

Trim off any excess fat.

The pieces of meat do not necessarily have to be turned.

Once cooked, the meat can be carved immediately; it does not have to rest.

Meat that is slow cooked is not as hot as meat cooked in the traditional way, so it is advisable to

put the plates in the warming drawer on the left-hand side for the last 20-30 minutes as well.

Serve the meat with piping hot sauces.

If you want to keep the meat hot after cooking, turn the knob to between WARM and MED

(105-140°F / 40-60°C). Smaller pieces of meat can be kept hot for 45 minutes and larger pieces

for two hours.

APPLICATIONS

Slow cooking is suitable for all tender cuts of beef, pork, veal, lamb, game and poultry. The

initial browning times and the subsequent cooking times depend on the size of the slices of

meat.

The browning time is for meat placed in a preheated pan with butter or oil.

DISH EXAMPLE INITIAL BROWNING LEVEL

Small slices of meat

Strips about 1 - 2 minutes MED

Small steaks or medallions about 1 - 2 minutes per side MED

Medium size slices of meat

Tenderloin about 4 - 5 minutes per side MAX

Lean roast about 10 - 15 minutes per side MAX

Large slices of meat

Tenderloin (from 2 Lb [900g]) about 6 - 8 minutes per side MAX

Roast beef about 8 - 10 minutes per side MAX

Vegetables about 30 minutes per side MED

NOTE: There are 2 settings: MAX and MED. Guidelines for cooking times are 4 to 5 hours for

MAX and 8 to 10 hours for MED. Smaller quantities of food may require less time, while larger

quantities may require more time.

USING THE WARMING DRAWER

(CONT.)

10

EN

CLEANING AND MAINTENANCE

DRAWER SLIDES

The drawer slides allow you to fully extend the drawer for cleaning. The drawer can be

removed for cleaning or to replace the interior lights.

NOTE: Load capacity for the drawer is 80 lbs (36 kg).

Remove all items from inside the warming drawer, and allow the warming drawer to cool

completely before attempting to remove the drawer.

To Remove:

1. Open drawer to its fully open position.

2. Locate the black tabs on both sides of the drawer.

3. Press the tab down on the right side of the

drawer and lift tab up on the left side of the

drawer at the same time. Then pull drawer out

another inch to disengage latch.

4. Hold the drawer by the sides (not by the front).

Pull it slowly all the way out.

TO REPLACE:

1. Align the drawer rails with the receiving slides.

2. Push drawer in all the way.

3. Gently open and close the drawer to ensure it is seated

properly on the slides.

11

EN

CLEANING AND MAINTENANCE

(CONT.)

CLEANING

The only recommended maintenance for the Warming Drawer is cleaning.

Before you begin cleaning, turn the appliance OFF and disconnect the appliance from the outlet.

Allow the appliance to cool before cleaning it.

NOTICE

Do not use harsh detergents or abrasive products and/or scrubbing pads and sponges and sharp

objects as they can stain and damage the appearance of the appliance.

Never use a vacuum cleaner on the internal parts of the appliance.

FRONT SURFACE AND CONTROL PANEL

The use of a moist cloth is often sufficient when cleaning the appliance. If needed, add a few

drops of detergent in the water. Dry the appliance with a dry cloth. The steel front of the

appliance can be cleaned with products specifically designed for steel.

Such products prevent the formation of dirt on the surface of the drawer. Apply a minimal

amount of the product on a soft and apply it to the surface of the appliance.

INSIDE SPACE

To clean the inside space use a moist cloth. In the event the appliance requires further cleaning

add drops of detergent to the water. Dry the surface with a dry cloth. Make sure to avoid water

draining into the ventilation holes. Only use the appliance after the drawer is completely dry.

REPLACING A WARMING DRAWER LIGHT BULB

The Warming Drawer is equipped with two halogen lights, located on the right side of the unit.

ELECTRICAL SHOCK HAZARD - Make sure the power has been shut off to the Warming

Drawer. The light socket is energized when the door is open. Failure to shut off the power when

replacing a light bulb could result in electric shock or burns.

Make sure the glass lens is cool to the touch. Use care when handling the lens, it is fragile and

can break if dropped.

Use only 20 watt, 12 Volt, halogen “Bi-Pin” bulbs suitable for appliance use. This type of bulb

may be available at hardware stores & home centers, or specialty lighting stores. Call Hestan

Customer Care for more information.

12

EN

TO REPLACE A LIGHT BULB

1. MAKE SURE POWER IS OFF! Unplug the unit or turn off power at the breaker.

2. Remove the lens retaining screw. Use a small flat-blade screwdriver to carefully pry off

the glass lens and set aside. Reach into the lamp housing and pull out the old light bulb as

shown in the image below.

3. Before installation, it is very important to clean the new bulb carefully with a clean, soft

cloth or tissue paper. Grease, fingerprints, or oils in your skin can leave a residue on the

glass surface of the bulb which will create a hot-spot. The bulb will eventually crack at this

hot-spot.

4. While still using a cloth or tissue paper, insert the new bulb in the lamp housing. Push the

bulb fully into the socket.

5. Re-install the glass lens taking note of the cutaway in the glass which aligns with the bulb

socket.

6. Restore the power and check if the new bulb is working. If the drawer was removed,

re-install it.

Retaining

screw

LIGHT BULBSOCKET

CLEANING AND MAINTENANCE

(CONT.)

13

EN

TROUBLESHOOTING

Repairs must only be performed by specialized and qualified personnel. Any repair work not

performed by professional personnel may cause damage to the appliance for which Hestan will

not be liable.

The following problems can be checked by the consumer without the assistance of the Service

Department.

THE DRAWER IS NOT HOT ENOUGH

Make sure that:

• The appliance is turned on;

• The correct temperature has been set;

• The opening of the ventilation fan is not blocked by plates or other large obstructions;

• The drawers have had sufficient time to heat up.

THE DRAWER DOES NOT GET WARM

Is it turned on? Is it turned on to DEFROST by mistake?

Can you hear the fan running?

• If the fan is running then the heating system should be working, except in DEFROST mode.

If the fan does not run, open the drawer and see if the interior lights come on. If neither light

comes on, check that the unit is plugged in and the breaker hasn’t tripped.

• If the light comes on but the fan doesn’t run, call Hestan Customer Care.

14

EN

INSTALLATION

APPLIANCE INSTALLATION

IMPORTANT: Save these instructions for the local electrical inspector use.

INSTALLER: Please leave this manual with owner for future reference.

OWNER: Please keep this manual for future reference.

If the information in this manual is not followed exactly, a fire or explosion may result causing

property damage, personal injury or death.

Please read these instructions COMPLETELY AND CAREFULLY. They will save you time and

effort and help to ensure optimum drawer performance.

Be sure to observe all CAUTIONS and WARNINGS. These installation instructions are intended

for use by a qualified installer.

• Assure that electrical installation is adequate and in conformance with National Electrical

Code, ANSI/ NFPA 70 - latest edition**, or Canadian Electrical Code, part 1 C22.1 (latest

edition)*** and all local codes and ordinances.

These shall be carefully followed at all times.

TOOLS YOU WILL NEED

• The following tools are needed to install your new warming drawer:

• Tape measure and straightedge or ruler

• Pencil

• Phillips screwdriver

• Level

• Wire cutters and wire stripper

• Hand or saber saw

• 1” (2,5cm) Hole saw

• Drill and drill bit

• Safety gloves and goggles

• Volt meter (0-250VAC)

PACKAGING

Remove all tape and packaging before using the warming drawer.

Destroy the packaging after unpacking the drawer following the rules in force in your locale.

Never allow children to play with packaging material.

POWER REQUIREMENTS

The warming drawer must be supplied with the proper voltage and frequency. The drawer

is manufactured to be connected to a three-wire, single phase, 120 Volt, 60 Hz AC electrical

supply.

POWER REQUIREMENT

Voltage 120 Volts, 60 Hz

Current 9.2 Amperes

Consumption 1100 Watts

15

EN

INSTALLATION

(CONT.)

CHOOSING DRAWER LOCATION

Carefully select the location where the warming drawer will be placed.

• It should be located for convenient use in the kitchen.

• Make sure that electrical power can be provided to the location selected. The receptacle

should be accessible after the drawer is installed, so that the drawer can be unplugged and

plugged in after installation. The cord is about 47” [120 cm] long.

PREPARATION

1. See drawings on following page for clearance and cutout dimensions

2. The warming drawer support surface must be a minimum 3/4” (2cm) thick plywood

platform. It must support 100 pounds.

3. The platform must be solid, level and flush with the bottom of the cabinet cut out.

4. The cabinet must be secure against tipping when the drawer is opened. Install anti-tip

brackets as needed.

5. For best performance results make sure the platform is level before placing the warming

drawer. There is no way to level the warming drawer after it has been installed.

• If the installation is not level, the door may slide open or not seal tightly, allowing heat to

escape.

CAUTION

• Use extreme caution when moving or installing the drawer. It is very heavy.

NOTICE

• DO NOT LIFT THE WARMING DRAWER BY THE DRAWER HANDLE.

• Be very careful when moving or installing the warming drawer to avoid damage to the frame

or damage to the cabinets.

• If installing the warming drawer below another product, refer to that product’s literature

for any installation requirements.

16

EN

PLACING THE DRAWER

• Unit is heavy and requires at least two people or

proper equipment to move.

Verify there is room to run the cord before placing the

drawer without pinching it.

1. If the plug will not be accessible after placing the

unit, turn power OFF at the service panel. Lock

service panel to prevent power from being turned

ON accidentally.

2. Run the cord through to the socket.

• If the plug will be accessible after placing the unit,

then run the cord through but don’t plug it in yet.

• If the plug will not be accessible after placing the

drawer, then plug it in.

INSTALLATION

(CONT.)

CABINET CUTOUT DIMENSIONS

28-7/16"

[ 722 cm]

9-1/4"

[ 235 cm]

Electrical

Location

24"

[ 610 cm]

OVERALL DIMENSIONS

10-3/8"

[ 264 cm]

29-5/8” to 29-7/8"

[ 754 to 758 cm]

23"

[ 581 cm]

8-1/4"

[ 208,5 cm]

9-1/16"

[ 230 cm]

23"

[ 583 cm]

[ 750 cm]

29-1/2"

[ 707 cm]

27-7/8"

10-3/8"

[ 264 cm]

29-5/8"

[ 754 cm]

23-3/4"

[ 601 cm]

9-1/16"

[ 230 cm]

23"

[ 583 cm]

[ 750 cm]

29-1/2"

[ 707 cm]

27-7/8"

10-3/8"

[ 264 cm]

24-3/4"

[ 631 cm]

29-7/8"

[ 758 cm]

9-1/16"

[ 230 cm]

23"

[ 583 cm]

[ 750 cm]

29-1/2"

[ 707 cm]

27-7/8"

17

EN

INSTALLATION

(CONT.)

3. Position the drawer so that it is directly centered and slide the warming drawer assembly

into cutout until it is flush with cabinet.

4. Securely fasten drawer to cabinet using the screws provided.

• Failure to secure the warming drawer could result in the drawer moving or tipping during

use and causing damage to the drawer or cabinets or personal injury.

5. Turn the power back on or plug the drawer in.

6. Turn the warming drawer to MAX. Observe that the light comes on. Close the drawer for

approximately 1 minute, then check for warmth.

7. Verify that the drawer is warming up, then turn the knob OFF.

• Make sure that the customer knows how to disconnect the power to the warming drawer

at the circuit breaker or fuse box in case of an emergency.

18

EN

La page charge ...

Hestan KWD30 Manuel utilisateur

Hestan KWD30 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents