Modern Forms PD-26316 Rollins Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
263-Mini Pendant
PD-26316
HARDWARE
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2022
CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning.
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chiffon humide.
Wire Connector
Qty:3+1Extra
A
C
Mounting Screw
Qty:1Extra
Wire Connector
Qty:2+1Extra
B
2
INSTALLATION INSTRUCTIONS
263-Mini Pendant
PD-26316
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Live)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2
Wiring
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2022
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture,
including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area.
Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the canopy screw (B) from the xture, and remove the ceiling plate.
4. Secure the ceiling plate to the junction box using the screws provided with the
junction box.
Note:
(i) It is recommended to use only original junction box screws or
replacements provided by junction box manufacturer.
(ii) The side of the ceiling plate marked “GND” must face out towards the installer.
5. Screw in the alabaster shade clockwise, and be careful not to touch the LED
module.
6. Choose number of down rods suitable for your application. Thread the xture
wires through the rods, swivel and canopy. Attach the canopy, rods, swivel
and xture body. Ensure all connections are tightened. Note: Due to limited
space within the canopy, shorten the cable as necessary to make the
installation easier. Make sure to identify and label all the wiring
properly (Fig. 3) before any trimming/shortening.
7. The swivel B can be adjusted about 15° in any direction. Adjust the swivel B to
keep it vertical with the rods and the xture.
CONNECTING THE WIRES (Fig. 2 / Fig. 3/ Fig. 4)
8. Connect the driver’s output wires to center cable as shown in Fig. 3, red to the
center, and black to the bare, make sure that wire connectors (B) are secured.
Then tuck them inside the canopy.
9. Connect the driver’s input wires to junction box wires as shown in Fig. 2, make sure
that all wire connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect the xture’s ground wire to it.
Otherwise, connect the xture’s ground wire directly to the back plate using the screw provided. After wires are connected, tuck them
carefully inside the junction box.
10. Secure the xture by mounting the canopy to the ring of the backplate. Turn androtate the canopy stops. Fasten the canopy to the
Ceiling plate using the canopy screw (B).
11. For slope ceiling application, rotate swivel at the top of the stem to ensure luminaries is aiming down (Fig. 4).
Ceiling Plate Dimensions
Ø4
5/8“
1
3/4“
1
3/8“
Fig.3 Driver Wiring
White - Neutral
Black - live
Red +
Black -
Center +
Bare -
Driver
Input
Output
Canopy
Fig.1
Junction Box
Wire Connector
A
Ceiling Plate
Canopy
Swivel A
C
Ground Wire
Fixture Body
Black Wire
White Wire
Canopy Screw
3x12"Rods
1x6"Rods
B
Junction Box
Screw
Wire Connector
Alabaster shade
Swivel B
Rotate swivel to
hang vertically
Fig.4
-
1
-
2
Modern Forms PD-26316 Rollins Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms WS-96318 Ezra Mode d'emploi
-
-
-
-
-
-
-
-
-
