Aruba 360 Series Guide d'installation

Marque: Aruba

Modèle: 360 Series

Catégorie: Points d'accès WLAN

Taper: Guide d'installation

Aruba 360 Series Outdoor Access Points

Installation Guide

Rev02 | February 2017 1

The Aruba 360 Series outdoor wireless access points support IEEE 802.11ac standards for high-

performance WLAN, and are equipped with two radios, which provide network access and monitor

the network simultaneously. Multiple-in, Multiple-out (MIMO) technology allows these access points

to deliver high-performance 802.11n 2.4 GHz and 802.11ac 5 GHz functionality, while also supporting

802.11a/b/g wireless services.

The 360 Series outdoor wireless access points provide the following capabilities:

 IEEE 802.11a/b/g/n/ac operation as a wireless access point

 IEEE 802.11a/b/g/n/ac operation as a wireless air monitor

 IEEE 802.11a/b/g/n/ac spectrum monitor

 Compatible with IEEE 802.3af PoE

 Integrated Bluetooth Low Energy (BLE) Radio

Package Contents

 360 Series access point

 Cable Gland x 1

 USB Console Cable x 1

 Copper Lug x 1

 M4x6 Screw x1

CAUTION

This device must be professionally installed and serviced by a trained ACMP or similar Aruba-certified

technician. Aruba access points are classified as radio transmission devices, and are subject to government

regulations of the host country. The network administrator(s) is/are responsible for ensuring that configuration

and operation of this equipment is in compliance with their country’s regulations. For complete list of

approved channels in your country of the AP-365 and AP-367 access points, refer to the Aruba Downloadable

Regulatory Table at support.arubanetworks.com.

Mounting kits for use with the 360 Series access points are sold separately. Contact your Aruba sales

representative for details.

Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton,

including the original packing materials. Use these materials to repack and return the unit to the supplier if

needed.

2 Aruba 360 Series Outdoor Access Points | Installation Guide

Hardware Overview

Figure 1 360 Series Access Point

LED

The 360 Series access point is equipped with one LED that indicates the system status of the device.

This LED can be configured via ArubaOS or Aruba Instant software into three separate modes:

 Normal mode (by default): See Table 1 and Table 2

 Off mode: LED is off

 Blink mode: LED blinks green (synchronized)

USB Console Port

The USB Micro-B console port allows you to connect the AP to a terminal or a laptop for direct local

management. Use the included USB console cable to connect the AP. You can download the

Table 1 360 Series LED Status during Boot Up

LED Color/State Meaning

System LED Off No power to AP

Red Initial power-up

Green - Flashing AP booting

Green - Steady AP ready and 1000Mbps Ethernet link established. The LED

turns off after 1200 seconds

Green - Yellow, 6 seconds

period

AP ready and 10/100Mbps Ethernet link established. The LED

turns off after 1200 seconds

Table 2 360 Series LED Status during Operation

LED Color/State Meaning

System LED Solid Red General fault

One blink off every 3

seconds

Radio 0 fault (5 GHz)

Two quick blink off 0.5

seconds apart cycled every

3 seconds

Radio 1 fault (2.4GHz)

Grounding Point

Ethernet Port

Air Vent

USB Console Port, Reset

button and LED

Aruba 360 Series Outdoor Access Points | Installation Guide 3

necessary driver for USB-UART adapter from support.arubanetworks.com under the Tools &

Resources tab.

Use the following setting to access the terminal:

Reset Button

To reset the 360 Series access points to factory default settings, press and hold down the reset

button using a small, narrow object such as a paper clip while the device is powered on.

Ethernet Ports

360 Series access point is equipped with one 10/100/1000Base-T auto-sensing MDI/MDX Ethernet

port. This port supports wired-network connectivity, in addition to Power over Ethernet (PoE) from

IEEE 802.3af compliant power sources.This device accepts 57V DC (802.3af) nominal as a standard

powered device (PD) from power sourcing equipment, including PoE midspan injector or a PoE-

sourcing network infrastructure.

The port has an RJ-45 female connectors with the pin-out shown in Figure 2.

Figure 2 Gigabit Ethernet Port Pin-Out

Grounding Point

Always remember to protect the access point by installing grounding lines. The ground connection

must be complete before connecting power to the access point enclosure.

Before You Begin

Table 3 Console Settings

Baud Rate Data Bits Parity Stop Bits Flow Control

9600 8 None 1 None

1000Base-T Gigabit

Ethernet Port

RJ-45 Female

Pin-Out

Signal Name

BI_DC+

BI_DC-

BI_DD+

BI_DD-

BI_DA+

BI_DA-

BI_DB+

BI_DB-

Function

Bi-directional pair +C, POE Positive

Bi-directional pair -C, POE Positive

Bi-directional pair +D, POE Negative

Bi-directional pair -D, POE Negative

Bi-directional pair +A, POE Negative

Bi-directional pair -A, POE Negative

Bi-directional pair +B, POE Positive

Bi-directional pair -B, POE Positive

CAUTION

FCC Statement: Improper termination of access points installed in the United States configured to non-US

model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or

intentional violation may result in a requirement by the FCC for immediate termination of operation and may

be subject to forfeiture (47 CFR 1.80).

4 Aruba 360 Series Outdoor Access Points | Installation Guide

Pre-Installation Network Requirements

After WLAN planning is complete and the appropriate products and their placement have been

determined, the Aruba controller(s) must be installed and initial setup performed before the Aruba

access points are deployed.

For initial setup of the controller, refer to the Quick Start Guide for the software version installed on

your controller.

Pre-Installation Checklist

Before installing your 360 Series access points, be sure that you have the items listed below:

 Cat5E UTP or better cable of required length

 802.3af-compliant PoE source

For 360 Series access points running ArubaOS only:

 Aruba Mobility Controller provisioned on the network:

 Layer 2/3 network connectivity to your access points

 One of the following network services:

 Aruba Discovery Protocol (ADP)

 DNS server with an “A” record

 DHCP Server with vendor-specific options

Verifying Pre-Installation Connectivity

Before installing access points in a network environment, make sure that they are able to locate and

connect to the controllerafter power on.

Specifically, you must verify the following conditions:

 When connected to the network, each access point is assigned a valid IP address.

CAUTION

EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User

Guide/Aruba Instant User Guide for details on restrictions.

Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous

referrer au ArubaOS User Guide/Aruba Instant User Guide pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich

Einschränkungen finden Sie im ArubaOS User Guide/Aruba Instant User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide/

Aruba Instant User Guide per avere informazioni detagliate sulle restrizioni.

Aruba Networks, Inc. in compliance with governmental requirements, has designed the 360 Series access

points so that only authorized network administrators can change the settings. For more information about

access point configuration, refer to the Quick Start Guide and ArubaOS User Guide/Aruba Instant User Guide.

The instructions for this section are applicable to the 360 Series access points running ArubaOS only.

Aruba 360 Series Outdoor Access Points | Installation Guide 5

 Access points are able to locate the controller.

Refer to the Quick Start Guide for instructions on locating and connecting to the controller.

Outdoor Planning and Deployment Considerations

Prior to deploying an outdoor wireless network, the environment must be evaluated to plan for a

successful Aruba WLAN deployment. Successfully evaluating the environment enables the proper

selection of Aruba routers and antennas and assists in the determination of their placement for

optimal RF coverage. This process is considered WLAN or RF planning and Aruba’s system engineers

can assist in the outdoor planning process.

For WLAN systems being installed outdoors in the USA, the following requirements must be met.

1. Systems must be professionally installed by a qualified engineer familiar with WLAN, including

Aruba trained partners and resellers.

2. Operation in the 5600-5650-MHz band is prohibited.

3. When within 35 km distance of a TDWR, the center frequency of the WLAN must be separated

from the TDWR center frequency by 30 MHz.

a. If the radar is operating from 5600-5610 MHz, disable the use of channel 116 (5580 MHz).

b. If the radar is operating from 5630-5650 MHz, disable the use of channel 132 (5660 MHz).

For TWDR locations in the US please refer to www.wispa.org/tdwr-locations-and-frequencies.

Identifying Specific Installation Locations

You can mount the 360 Series access point on a wall or pole. Use the access point placement map

generated by Aruba’s RF Plan software application to determine the proper installation location(s).

Each location should be as close as possible to the center of the intended coverage area and should

be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/

interference sources will impact RF propagation and should have been accounted for during the

planning phase and adjusted for in RF plan.

Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field during the

installation phase is critical. Make sure that these sources are taken into consideration when you

attach an AP to its fixed location. Examples of sources that degrade RF performance include:

 Cement and brick

 Objects that contain water

 Metal

 Microwave ovens

 Wireless phones and headsets

Installing the Access Point

Using the Mounting Kits

The 360 Series can be installed on a wall or attached to a pole by using applicable mounting kits. The

AP-365 access point is equipped with built-in omni-directional antennas which are optimized for

horizontal mounted orientation of the AP-365 access point. The AP-367 access point is equipped with

Service to all Aruba products should be performed by an AMCP certified technician or similar.

6 Aruba 360 Series Outdoor Access Points | Installation Guide

built-in directional antennas which are optimized for vertical mounted orientation of the AP-367

access point.

Grounding the AP

The grounding must be completed before powering up the access point. The grounding wire should

be #8 AWG.

1. Peel the cover of one end of the grounding wire and place the bare grounding wire into the

included copper lug, and press firmly with the crimping pliers.

2. Fasten the copper lug to the grounding hole on the AP with the included M4 x6 screw.

Connecting the Ethernet Cable

To connect the Ethernet cable to the access point, perform the following steps using the cable gland

that ships with your access point.

Table 4 Applicable Mounting Kits for 360 Series

Part Number Description

Applicable for

AP-365?

Applicable for

AP-367?

AP-270-MNT-V1 Long mount kit for wall and vertical pole

mounting, 300 mm from vertical mounting

asset.

Yes No

AP-270-MNT-V2 Short mount kit for wall and vertical pole

mounting, 75 mm from vertical mounting asset.

Yes No

AP-270-MNT-H1 Hanging mount kit for hanging from inclined or

horizontal structure.

Yes Yes

AP-270-MNT-H2 Flush mount kit for wall and ceiling mounting. Yes Yes

The 360 Series access point does not ship with any mounting kits. These mounting kits are available as

accessories and must be ordered separately.

For installation instructions on AP-270-MNT-V1, AP-270-MNT-V2, AP-270-MNT-H1 and AP-270-MNT-H2, please

refer to the AP-270-MNT-V1 Installation Guide, AP-270-MNT-V2 Installation Guide, AP-270-MNT-H1 Installation

Guide and AP-270-MNT-H2 Installation Guide respectively.

WARNING

Failure to use the included Ethernet cable gland can lead to connectivity and POE issues.

The cable is not included and must be purchased separately. Purchase a suitable UV-resistant, outdoor rated,

CAT 5E or better RJ45 cable for use with the access point.

Aruba 360 Series Outdoor Access Points | Installation Guide 7

Figure 3 Installing the Cable Gland

1. Slide the sealing nut over the cable (without the RJ45 connector attached to the end).

2. Slide the clamping ring over the cable.

3. Using a crimping tool, attach the shielded RJ45 connector to the end of the cable.

4. Remove the weatherproof cap on the Ethernet port.

5. Insert the RJ45 connector to the Ethernet port.

6. Screw the clamping ring onto the Ethernet port.

7. Screw the sealing nut onto the clamping ring.

Verifying Post-Installation Connectivity

The integrated LED on the AP can be used to verify that the access point is receiving power and

initializing successfully (see Table 1 and Table 2). Refer to the Quick Start Guide for further details on

verifying post-installation network connectivity.

Configuring the Access Point

Access Point Provisioning/Reprovisioning

Provisioning parameters are unique to each access point. These local access point parameters are

initially configured on the controller which are then pushed out to the AP and stored on the AP itself.

Aruba recommends that provisioning settings be configured via the ArubaOS Web UI only. Refer to

the ArubaOS User Guide for complete details.

Access Point Configuration

Configuration parameters are network or controller specific and are configured and stored on the

controller. Network configuration settings are pushed out to the AP(s) but remain stored on the

controller.

Configuration settings can be configured via the ArubaOS Web UI or ArubaOS CLI. Refer to the

ArubaOS User Guide for complete details.

Sealing Nut

Clamping Ring

CAT 5E or Better Cable

Seals

The seals inside the clamping ring by factory default is applicable for cables with 5-8.5 mm diameter. In the

cable gland kit, another seals is provided for use with the cables with 7-10 mm diameter.

The instructions for this section are applicable to the 360 Series access points running ArubaOS only.

8 Aruba 360 Series Outdoor Access Points | Installation Guide

Electrical and Environmental Specifications

For additional specifications on this product, please refer to the product data sheet at

www.arubanetworks.com.

Electrical

 Ethernet:

 One 10/100/1000 Base-T auto-sensing Ethernet interface (RJ-45)

 Power:

 Maximum (worst-case) power consumption: 12.95W (802.3af PoE)

 Power over Ethernet (PoE): 802.3af complaint source

 Connect only to IEC 60950-1 or IEC 60601-1 3rd edition products and power sources.

Environmental

 Operating:

 Temperature: -40°C to +50°C (-40°F to +122°F)

 Humidity: 5% to 93% non-condensing

 Storage and transport

 Temperature: -40°C to +70°C (-40°F to +158°F)

Regulatory Information

The following regulatory model names apply to the 360 Series access points:

 AP-365: APEX0365

 AP-367: APEX0367

FCC

This device is electronically labeled.

To view the FCC ID for controller-managed access points:

1. Log into the controller WebUI

2. Navigate to Maintenance > Controller > About

To view the FCC ID for Instant access points:

1. Log into the virtual controller WebUI

2. Navigate to Maintenance > About

CAUTION

All Aruba access points should be professionally installed by an Aruba Certified Mobility Professional (ACMP).

The installer is responsible for ensuring that grounding is available and meets applicable national and electrical

codes.

CAUTION

Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier

doit s'assurer que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes

électriques nationaux en vigueur.

CAUTION

RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This

equipment must be installed and operated in accordance with provided instructions and the antenna(s) used

for this transmitter must be installed to provide a separation distance of at least 20cm from all persions and

must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and

installers must be provided with antenna installation instructions and transmitter operating conditions for

satisfying RF exposure compliance.

Aruba 360 Series Outdoor Access Points | Installation Guide 9

FCC Class B Part 15

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio or TV technician for help.

Industry Canada

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Déclaration d’Industrie Canada

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio

exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit

pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

CAUTION

Déclaration sur les limites d'exposition aux radiofréquences :cet équipement est conforme aux limites

d'exposition aux rayonnements radioélectriques spécifiées par la FCC. Il doit être installé et utilisé à une

distance minimale de 20 cm par rapport à votre corps pour les fréquences de 2,4 et 5 GHz. Cet émetteur-

récepteur ne doit pas être utilisé ou situé à proximité d'autres antennes ou émetteurs-récepteurs.

CAUTION

The device could automatically discontinue transmission in case of absence of information to transmit, or

operational failure. Note that this is not intended to prohibit transmission of control or signaling information

or the use of repetitive codes where required by the technology.

CAUTION

Any changes or modifications not expressly approved by the grantee of this device could void the user’s

authority to operate this equipment.

CAUTION

Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la

conformité est susceptible d'annuler son droit d'utilisation.

CAUTION

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20 cm between the radiator and your

body.

CAUTION

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement

non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la

source de rayonnement et votre corps.

10 Aruba 360 Series Outdoor Access Points | Installation Guide

EU Regulatory Conformance

Aruba Networks Inc., hereby declares that the 360 Series Wireless Access Points are in

compliance with directives listed below

 EMC Directive 2014

 Low Voltage Directive 2014

 R&TTE Directive 1999

 REACH Regulation (EC) No.: 1907/2006

 RoHS Directive 2011

 WEEE Directive 2012

A Declaration of Conformity for these directives is available for viewing at www.arubanetworks.com.

EMC Class B Warning

이 기기는 가정용 (B 급 ) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며 , 모든 지역에서 사용할 수 있습니다 .

RF Warning

해당무선설비는 전파혼신의 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다

Medical

1. Equipment not suitable for use in the presence of flammable mixtures.

2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is

responsible for the resulting medical system complies with the requirements of IEC 60601-1 3rd edition.

3. Wipe with a dry cloth, no additional maintenance required.

4. No serviceable parts, the unit must be sent back to the manufacturer for repair.

5. No modifications are allowed without Aruba approval.

第十二條

　　經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計

之特性及功能。

第十四條

　　低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時

方得繼續使用。

CAUTION

(i) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-

5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and

non-point-to-point operation as appropriate; and

(ii) Users should also be advised that high power radars are allocated as primary users (i.e. priority users) of the

bands 5650-5850MHz and that these radars could cause interference and/or damage to LE-LAN devices.

CAUTION

(i) pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis (pour les dispositifs

utilisant la bande de 5 725 à 5 850 MHz) doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation

point à point et l'exploitation non point à point, selon le cas;

(ii) Les utilisateurs devraient aussi être avisés, d’une part, que les utilisateurs de radars de haute puissance

sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) des bandes de 5 650 à 5 850 MHz et, d’autre

part, que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs de RL-EL.

CAUTION

This radio transmitter (IC: 4675A-APEX0365367) has been approved by Industry Canada to operate with the

antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this

list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with

this device.

CAUTION

Le présent émetteur radio (IC: 4675A-APEX0365367) a été approuvé par Industrie Canada pour fonctionner

avec les types d'antenne énumérés ci dessous et ayant un gain admissible maximal. Les types d'antenne non

inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour

l'exploitation de l'émetteur.

Aruba 360 Series Outdoor Access Points | Installation Guide 11

　　前項合法通信，指依電信法規定作業之無線電通信。

　　低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾

。

Proper Disposal of Aruba Equipment

Dispose of Aruba products per local regulation. For the most current information about Global

Environmental Compliance and Aruba products, see our website at www.arubanetworks.com.

Waste of Electrical and Electronic Equipment

Aruba products at end of life are subject to separate collection and treatment in the

EU Member States, Norway, and Switzerland and therefore are marked with the

symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of

life of these products in these countries shall comply with the applicable national

laws of countries implementing Directive 2002/96EC on Waste of Electrical and

Electronic Equipment (WEEE).

India RoHS

This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling)

Rules, governed by the Ministry of Environment & Forests, Government of India.

European Union RoHS

Aruba products also comply with the EU Restriction of Hazardous Substances

Directive 2011/65/EC (RoHS). EU RoHS restricts the use of specific hazardous

materials in the manufacture of electrical and electronic equipment. Specifically,

restricted materials under the RoHS Directive are Lead (including Solder used in

printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba

products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in

printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at

the left indicating conformance to this directive.

China RoHS

Aruba products also comply with China environmental declaration requirements and

are labeled with the “EFUP 10” label shown at the left.

Expected Service Life 10 years. For additional compliance information, refer to the label on the side of this device.

ᴹᴹ∂ᴹᇣ⢙䍘༠᰾

Hazardous Materials Declaration

䜘Ԧ਽〠

(Parts)

ᴹ∂ᴹᇣ⢙䍘ᡆݳ㍐˄Hazardous Substance˅

䫵

˄Pb˅

⊎

˄Hg˅

䭹

˄Cd˅

ޝԧ䬜

˄Cr

ཊⓤ㚄㤟

˄PBB˅

ཊⓤҼ㤟䟊

˄PBDE˅

⭥䐟⁑ඇ

(circuit modules)

XOOOO O

⭥㔶৺⭥㔶㓴Ԧ

(Cables & Cable A

ssemblies)

OOOOO O

䠁኎䜘Ԧ

(Metal Parts)

OOOOO O

ກᯉ઼㚊ਸ⢙䜘Ԧ

(

Plastic and Polymeric Parts)

OOOOO O

O: 㺘⽪䈕ᴹ∂ᴹᇣ⢙䍘൘䈕䜘Ԧᡰᴹ൷䍘ᶀᯉѝⲴਜ਼䟿൷൘ SJ/T11363-2006 ḷ߶㿴ᇊⲴ䲀䟿㾱≲

ԕлǄ

Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts

is below the relevant threshold of the SJ/T11363-2006 standard.

X: 㺘⽪䈕ᴹ∂ᴹᇣ⢙䍘㠣ቁ൘䈕䜘ԦⲴḀа൷䍘ᶀᯉѝⲴਜ਼䟿䎵ࠪ SJ/T11363-2006 ḷ߶㿴ᇊⲴ䲀

䟿㾱≲ǄIndicates that the concentration of the hazardous substance of at least one of all homogeneous

materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.

ሩ䬰୞ѻᰕⲴᡰ୞ӗ૱ˈᵜ㺘ᱮ⽪׋ᓄ䬮Ⲵ⭥ᆀؑ᚟ӗ૱ਟ㜭वਜ਼䘉Ӌ⢙䍘Ǆ

This table shows where these substances may be found in the supply chain of

electronic information

products, as

of the date of sal

e of the enclosed product.

↔ḷᘇѪ䪸ሩᡰ⎹৺ӗ૱Ⲵ⧟؍֯⭘ᵏḷᘇ. ḀӋ䴦䜘ԦՊᴹањн਼Ⲵ⧟؍֯⭘ᵏ

(

ֻྲ,⭥⊐অݳ⁑ඇ)䍤൘ަӗ૱к.

↔⧟؍֯⭘ᵏ䲀ਚ䘲⭘Ҿӗ૱ᱟ൘ӗ૱᡻޼ѝᡰ㿴ᇊⲴᶑԦлᐕ֌.

The Environment

Friendly Use Period (EFUP) for all enclosed products and their parts are

per the symbol shown here. The Environment

Friendly Use Period is valid only when the

product is operated under the conditions defined in the product manual.

www.arubanetworks.com

3333 Scott Blvd

Santa Clara, CA 95054

12 Aruba 360 Series Outdoor Access Points | Installation Guide

Contacting Support

Open Source Code

This product includes code licensed under the GNU General Public License, the GNU Lesser General Public

License, and/or certain other open source licenses. A complete machine-readable copy of the source code

corresponding to such code is available upon request. This offer is valid to anyone in receipt of this information

and shall expire three years following the date of the final distribution of this product version by Hewlett Packard

Enterprise Company. To obtain such source code, send a check or money order in the amount of US $10.00 to:

Hewlett Packard Enterprise Company

Attn: General Counsel

3000 Hanover Street

Palo Alto, CA 94304

USA

Warranty

This hardware product is protected by an Aruba warranty. For details, see Aruba Networks standard warranty

terms and conditions.

Main Site arubanetworks.com

Support Site support.arubanetworks.com

Airheads Social Forums and Knowledge

Base

community.arubanetworks.com

North American Telephone 1-800-943-4526 (Toll Free)

1-408-754-1200

International Telephones arubanetworks.com/support-services/contact-support/

Software Licensing Site hpe.com/networking/support

End-of-life Information arubanetworks.com/support-services/end-of-life

Security Incident

Response Team (SIRT)

Site: arubanetworks.com/support-service/security-bulletins/

Email: [email protected]

Aruba 360 Series Guide d'installation

Marque: Aruba

Modèle: 360 Series

Catégorie: Points d'accès WLAN

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Aruba 360 Series Installation guide

Aruba 360 Series Guide d'installation

Aruba 360 Series Guide d'installation

dans d''autres langues

Documents connexes

Autres documents