Aerohive AP370 Manuel utilisateur

Catégorie
Antennes réseau
Taper
Manuel utilisateur

Ce manuel convient également à

Aerohive QuickStart for the AP370 and AP390
This guide explains how to install an Aerohive AP370 or AP390 access point so it can make a network
connection to HiveManager. The instructions in this document apply to both models. To register, get
the latest product documentation, (including translations of select documents), see compliance
information, and download software updates, visit www.aerohive.com/support.
©
2013 Aerohive Networks, Inc.
Aerohive
®
is a U.S. registered trademark of Aerohive Networks, Inc.
P/N 330102-01 Rev. A
You can mount the AP370 or AP390 on a dust-free surface, on a wall, or to the tracks of a
dropped ceiling grid that will support its weight (AP370: 1 lb or .45 kg; AP390: 20 oz or .57 kg). The
wall and ceiling mounting options are explained below and on the next panel.
Mounting the AP370 and AP390
Cut a small hole in the ceiling tile to accommodate the cables. Connect the cables and,
for optimal reception, align external antennas for the AP390 as shown below.
The status LED on the top of the device displays the following activity states:
• Dark: Power is off, or the indicator has been disabled.
• Amber (fl ashing): The device is performing a fi rmware upgrade. Do not power off the device
during this process.
• Amber (solid): This indicates that the CAPWAP connection has not been successfully
established, or the device is booting or shutting down.
• White: The device is powered on and operating properly, and has made a successful
CAPWAP connection through the ETH0 interface.
Status LED
You can mount the AP370 or AP390 to the tracks of a dropped ceiling grid using the
mounting tabs and clips on the back of the device. The tabs slip over the edge of the
ceiling track and the clips click into place to secure the device.
The ceiling mounting options are shown below. The mounting hardware on the device
allows you to mount it diagonally, or square to the track.
Ceiling Mount
To mount the device on a ceiling track in either the diagonal or square position, hold the device
so that you are touching the appropriate tabs (as shown in the previous illustrations). Hold the
device upside down and press it gently against the ceiling track. Use your fi ngers to guide one
of the tabs over the edge of the track. Then rotate the device counter-clockwise (facing the
device) until the clips click into place.
To remove the device, press the clips toward the device until they disengage from the track,
then rotate the device gently and pull it away from the track.
The illustrations below show how to install the device on a ceiling track in the diagonal position.
To mount the device the square position, use the square-mount tabs and clips and follow the
same steps.
Use your fi ngertips to align the tabs
with the track.
1
2
Rotate the device until the
clips click into place.
You can secure the AP using a Kensington lock, or you can use the security bracket and screw
that ships with the device to secure it to a ceiling track or to a wall, as shown in the illustrations
below. To use a Kensington lock, loop the lock cable around a secure object, insert the T-bar
component of the lock into the lock slot on the AP and then turn the key to engage the lock.
To secure the AP to a ceiling track or a wall using the security bracket and screw, you will need
a spanner bit for size #6 security screws, and a driver handle that will accept the bit. Bits are
available from Aerohive in sets of three (AH-ACC-SEC-BIT-300-100-3PK). To use the security screw,
refer to the illustrations below. If you use a slotted screw, you will need a fl at-blade screwdriver.
Aerohive recommends the following Kensington lock models:
NOTE: This list to be completed after PVT phase.
Locking the Device
Diagonal mount
lock slot
Square mount
lock slot
5GHz(0)
Kensington
lock slot
Guide security bracket along the
lock slot until the screw holes align
and the end of the bracket slips
under the clip.
Clip
Security
bracket
Security
screw
Aligning AP390 External Antennas
Diagonal
mount clip
Diagonal
mount clip
Diagonal mount tab
(under fingertip)
CLICK!
CLICK!
Diagonal mount
tab (under
fingertip)
Note: For a square mount,
rotate in the opposite
direction.
Ceiling track
Diagonal installation
Square installation
You can attach the AP to any surface that supports its weight
(less than x lb or .xx kg for either device), and to which you can
install M4 mounting screws. There are four wall mount slots on
the back of the device. Measure the distances between the
centers of these slots and drill corresponding holes in the wall, or
use the template in the Aerohive Hardware Reference Guide at
www.aerohive.com/support/tech-docs-and-online-training to
mark the drill holes. Install size M4 screws. If you are connecting
to cables from inside the wall, drill a hole in the wall so that you
can pass the cables through to the AP. Finally, connect the
cables to the device.
Wall Mount
Wall mount slots
Diagonal
mount clip
and tab
Square
mount clip
and tab
Diagonal
mount clip
and tab
Tab
Clip
Square
mount clip
and tab
After you power on the AP, it automatically tries to get network settings and contact HiveManager.
This process takes about fi ve minutes. When you see the AP listed on the All Devices page in the
Monitor section of the HiveManager GUI, the initial setup is complete and you can begin managing
the AP using HiveManager.
If the AP does not appear after about ten minutes, see the Aerohive product documentation and
computer-based training modules to learn what you can do to help establish the connection. These
resources are available for free at www.aerohive.com/support/tech-docs-and-online-training.
Switch
DHCP
server
Firewall
Internet
Some other network devices (They
might all be incorporated in the same
device, such as a router or firewall.)
1
Ethernet
cable
2
ETH0
Connect a standard
RJ45 Ethernet cable
from ETH0 on the AP to
a switch.
3
For AP390 models, attach external antennas
to the 5 GHz and 2.4 GHz connectors.
AP370
Connecting the Device
If the switch provides
PoE, cabling the AP to the
switch will cause the AP to
power on in a few seconds.
If the switch does not provide PoE,
use the AC/DC power adaptor, power
supply, or PoE injector (all available
as accessories).
AP370 Kit Contents
• AP370 device with USB
slot cover installed
• 2 security screws
• 2 slotted screws
• 1 security bracket
• QuickStart Guide
AP390 Kit Contents
• AP390 device with USB slot
cover installed
• 2 security screws
• 2 slotted screws
• 1 security bracket
• QuickStart Guide
(Antennas must be ordered
separately)
Optional Accessories
You can order the following accessories for AP370 and AP390 devices:
NOTE: This list to be completed after PVT phase.
PoE injector and AC power adapter - (12Vdc, 2A or 55Vdc, 0.6A/PoE)
Optional mounting brackets for non-standard ceiling tracks:
15/16" recessed
3/8" fl ushed and recessed
9/16" fl ushed and recessed,
Plenum and suspend mount kits
45°
90° to wall
straight
straight
straight
45°
straight
90° to
ceiling
Ceiling
mount
Wall
mount
45°
45°
WARNING: FOR INDOOR USE ONLY. The AP370 and AP390 devices, DC power
adapter and all connected cables are designed for indoor use only.
© 2011 Aerohive Networks, Inc. All rights reserved. 330033-13 Rev. B
AerohiveHiveAPComplianceInformation
Federal Communication Commission Interference
Statement
Aerohive products (FCC models, AH-AP-110-N-FCC, AH-AP-120-N-FCC,
AH-AP-121-N-FCC , AH-AP-141-N-FCC, AH-AP-170-N-FCC, AH-AP-320-N-FCC,
AH-AP-330-N-FCC, AH-AP-340-N-FCC , AH-AP-350-N-FCC, AP370/AP390,
AH-BR100-N-FCC, AH-BR200-WP-N-FCC comply with part 15 of the FCC Rules
when operating under the following restrictions: (1) they do not cause harmful
interference, and (2) they must accept any RF interference received, including
interference that might cause an unwanted impact on their operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
In compliance with FCC Part 15 regulations, the HiveAP automatically
discontinues transmission if there is no valid information to transmit or if there
is an operational failure.
Important: FCC Regulatory Warning Notices
HiveAP 110, 120, 320, 330, 340, 350, AP370/AP390 and BR100 devices are
restricted to indoor use due to their operation in 5GHz frequencies, which are
shared by mobile satellite systems and government radar systems. The FCC
requires that these products only be used indoors to reduce the potential for
harmful interference with co-channel radar that might be operating in the
5.25-5.35 or 5.47-5.725 GHz frequency ranges in the same area. The conflicting
activity of radar stations and these devices can cause interference or damage to
each other. In addition, these devices have a radar detection function that
might interrupt normal operations when they detect a radar signal. To reduce
the risk of interference even further, installing these devices away from
windows is recommended.
HiveAP devices operating within the 5.15-5.25 GHz frequency range are
restricted to indoor environments.
The FCC region code is set in the device during the manufacturing process, the
option to set it to any region other than FCC is disabled, and the country code
selection function has been completely removed from all U.S. models. It is
impossible for the end user to change the region to anything other than FCC.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 2
FP between the radiator and
y
our body if using AP170 directional antenna (part number AH-ACC-170-ANT-18)
the distance is 65cm. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
The availability of some specific channel and/or operational frequency bands
are country dependent and are firmware programmed at the factory to match
the intended destination. The firmware setting is not accessible by end user.
Only attach antennas that are certified for use with this device. Replacing
antennas with unauthorized, high-gain antennas greatly increases the risk of
interference and invalidates the FCC certification.
Industry Canada
Note: The term "IC" before the radio certification number signifies that Industry
Canada technical specifications were met.
Products that show an Industry Canada identifier on the product label (IC
HiveAP 120, 121, 141, 170,320, 330, 340, 350, AP370/AP390, BR100, BR200 and
BR200-WP) can be operated in Canada under the following restrictions:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
IC Radiation Exposure Statement
Radiation Exposure Statement: This equipment complies with IC radiation
exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 2 cm between
the radiator and your body, if using AP170 directional antenna (part number
AH-ACC-170-ANT-18) the distance is 65cm.
For the models using “detachable Antenna”
The HiveAP 170/350/AP3$30 has been designed to operate with an antenna
having a Dipole maximum gain dBi. Antenna having a higher
gain is strictly
prohibited per regu
lations of Industry Canada. The required antenna impedance
is 50 ohms.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to other
users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (E.I.R.P) is not more than that necessary for
successful communication.
This radio transmitter (IC: $$3;/ Model: $3$3)
has been approved by Industry Canada to operate with the antenna types listed
below with the maximum permissible gain and required antenna impedance for
each antenna type indicated. Antenna types not included in this list, having a
gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
: Dipole/
4dBi
For the m
odels supporting 5GHz frequencies
Caution: The device for the band 5150-5250 MHz is only for indoor usage to
reduce potential for harmful interference to co-channel mobile satellite
systems.
High power radars are allocated as primary users (meaning they have priority) of
5250-5350 MHz and 5650-5850 MHz and these radars could cause interference
and/or damage to LE-LAN devices.
The band from 5600-5650 MHz will be disabled by the proprietary software
during the manufacturing and which cannot be changed by the end user.
Pour le modèle à l'aide antanna Détachables
Note: Le terme “IC” précédant le numéro de certification radio signifie que les
spécifications techniques de l’Industrie du Canada ont été respectées.
CAN ICES-3 (B)/NMB-3(B)
For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
Selection of other channels is not possible. Pour les produits disponibles aux
États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités.
Sélection d'autres canaux n'est pas possible.
Aerohive HiveAP Compliance Information 2
© 2011 Aerohive Networks, Inc. All rights reserved. 330033-13 Rev. B
Les produits indiquant un identifiant d’Industrie du Canada sur leur étiquette
(IC: $$3;) peuvent être exploités au Canada dans le
cadre des
restrictions suivantes:
Ce dispositif est co
nforme à la norme CNR-210 d'Industrie Canada applicable
aux appareils radio exempts de licence. Son fonctionnement est sujet aux
deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y
compris un brouillage susceptible de provoquer un fonctionnement
indésirable.
NOTE IMPORTANTE:
Déclaration d'exposition aux radiations: Cet équipement est conforme
aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé
avec un minimum de 2 cm de distance entre la
source de rayonnement
et votre cor
ps.
Ce dispositif a été conçu pour fonctionner avec une P
CB dipole antenne ayant un
gain maximal de dB [4
]. Une antenne à gain plus élevé est strictement interdite
par l
es règlements d'Industrie Canada. L'impédance d'antenne requise est de
50
ohms.
Conformément à la réglementation d'Industrie Canada, le présent émetteur
radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou
inférieur) approuvé pourl'émetteur par Industrie Canada. Dans le but de réduire
les risques de brouillage radioélectriqueà l'intention des autres utilisateurs, il
faut choisir le type d'antenne et son gain de sorte que lapuissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire
àl'établissement d'une communication satisfaisante.
Le présent émetteur radio (IC: $$3;/ Modèle: $3$3
) a été approuvé par Industrie Canada pour fonctionner avec les types
d'antenne énumérés ci-dessous et ayant un gain admissible maximal et
l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus
dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont
strictement interdits pour l'exploitation de l'émetteur.
Approved antenna(s) list
HiveAP 141/AP390:
Type Gain Brand Manufacturer
Dipole 4dBi Master Wave 98152MRSX007
Dipole 3dBi Master Wave 98152URSX002
HiveAP 121
Type Gain Brand Manufacturer
PCB Dipole 3dBi Master Wave 98P33MIPF006
PCB Dipole 3dBi Master Wave 98P33MIPF007
PCB Dipole 6dBi Master Wave 98P93UIPF000
PCB Dipole 6dBi Master Wave 98P93UIPF001
Le point d’accès HiveAP170 a été conçu pour fonctionner avec une Dipole
antenne ayant un gain maximal de dBi 4. Une antenne à gain plus élevé est
strictement interdite par les règlements d'Industrie Canada. L'impédance
d'antenne requise est de 50 ohms.
Conformément à la réglementation d'Industrie Canada, le présent émetteur
radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou
inférieur) approuvé pourl'émetteur par Industrie Canada. Dans le but de réduire
les risques de brouillage radioélectriqueà l'intention des autres utilisateurs, il
faut choisir le type d'antenne et son gain de sorte que lapuissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire
àl'établissement d'une communication satisfaisante.
Le présent émetteur radio (IC: $$3; / Model: $3$3) a été
approuvé par Industrie Canada pour fonctionner avec les types d'antenne
énumérés ci-dessous et ayant un gain admissible maximal et l'impédance
requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette
liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement
interdits pour l'exploitation de l'émetteur.
Avertissement: Le dispositif fonctionnant dans la bande 5150-5250 MHz les
risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant
les mêmes canaux.
Pour le modèle de fréquences 5GHz
Les utilisateurs de radars de haute puissance sont désignés utilisateurs
principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz et
5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des
dommages aux dispositifs LAN-EL.
La bande de frequence de 5600-5650MHz devra etre desactivee par logiciel lors
de la conception et ne devra comporter aucune possibilite de modification par
l'utilisateur final.
Wi-Fi Certification
The Wi-Fi CERTIFIED™ Logo is a certification mark of the Wi-Fi Alliance
®
. The
HiveAP 20, 100, 300 series have been certified for WPA™, WPA2™, WMM
®
(Wi-Fi
Multimedia™), WMM Power Save, IEEE 802.11d, IEEE 802.11h, and the following
types of EAP (Extensible Authentication Protocol):
EAP-TLS • EAP-SIM
EAP-TTLS/MSCHAPv2 • EAP-AKA
PEAPv0/EAP-MSCHAPv2 • EAP-FAST
PEAPv1/EAP-GTC
The HiveAP 100 and 300 series have also been certified for short guard interval
and 40-MHz operation in the 5-GHz band.
EC Conformance Declaration
Marking by the above symbol indicates compliance with the Essential
Requirements of the R&TTE Directive of the European Union (1999/5/EC). The
HiveAP 110, 120, 320, and 340 platforms meet the following conformance
standards:
EN 60950-1 (IEC 60950-1) 2
nd
edition - Product Safety
EN 301 893 - Technical requirements for 5 GHz radio equipment
EN 300 328 - Technical requirements for 2.4 GHz radio equipment
EN 301 489-1 / EN 301 489-17 - EMC requirements for radio equipment
The HiveAP 170, 330, and 350 platforms comply with the essential requirements
of the R&TTE Directive 1999/5/EC. The following test methods have been
applied to prove presumption of conformity with the essential requirements of
the R&TTE Directive 1999/5/EC:
EN 60950-1:2006+A11:2009+A1:2010
Safety of Information Technology Equipment
EN 50385: 2002
Generic standard to demonstrate the compliance of electronic and
electrical apparatus with the basic restrictions related to human exposure
to electromagnetic fields (0 Hz - 300 GHz)
EN 300 328 V1.7.1: 2006
Electromagnetic compatibility and Radio spectrum Matters (ERM);
Wideband Transmission systems; Data transmission equipment operating in
the 2.4 GHz ISM band and using spread spectrum modulation techniques;
Harmonized EN covering essential requirements under article 3.2 of the
R&TTE Directive
EN 301 893 V1.5.1: 2008
Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN;
Harmonized EN covering essential requirements of article 3.2 of the R&TTE
Directive
EN 301 489-1 V1.8.1: 2008
Electromagnetic Compatibility and Radio Spectrum Matters (ERM);
Electromagnetic Compatibility (EMC) standard for radio equipment and
services; Part 1: Common technical requirements
EN 301 489-17 V2.1.1: 2009
Electromagnetic Compatibility and Radio spectrum Matters (ERM);
Electromagnetic Compatibility (EMC) standard for radio equipment and
services; Part 17: Specific conditions for 2.4 GHz wideband transmission
systems and 5 GHz high performance RLAN equipment
The HiveAP 170, 330, and 350 are 5 GHz wideband transmission systems
(transceivers), intended for use in all EU member states and EFTA countries,
except in France and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum
authorities in order to obtain authorization to use this equipment for setting up
Aerohive HiveAP Compliance Information 3
© 2011 Aerohive Networks, Inc. All rights reserved. 330033-13 Rev. B
outdoor radio links and/or for supplying public access to telecommunications
and/or network services.
These devices may not be used for setting up outdoor radio links in France and in
some areas the RF output power may be limited to 10 mW EIRP in the frequency
range of 2454–2483.5 MHz For detailed information the end-user should contact
the national spectrum authority in France.
Declarations of conformity, compliance statements, and other regulatory
documentation are available at www.aerohive.com/support
.
WEEE and RoHS Compliance
Aerohive Networks products have been reviewed, analyzed and found to be in
compliance with the European Union (EU) directive for Waste Electrical and
Electronic Equipment (WEEE) and with the EU directive for the Restriction of
Hazardous Substances (RoHS).
WEEE Collection Programs in the U.S. and EU
At end of life, customers are requested to contact Aerohive to make
arrangements for WEEE collection of their products. The Aerohive collection
center in the U.S. is at the following address:
Aerohive Inc.
330 Gibraltar Drive
Sunnyvale, CA 94089
Telephone: 408-510-6100
Contact: Technical Support, weee@aerohive.com
Aerohive, in association with M-Cubed LLC, also has a collection center at the
following address in Germany, a member state of the European Union:
EXTRABYTE - M Cubed LLC
Klopstock Strasse #8
33613 BIELEFELD
Telephone: 49-521-882245
Contact: Mr. Andreas Budde
Countries of Operation and Conditions
of Use in the European Community
HiveAPs are intended to be operated in all countries of the European
Community. Requirements for indoor vs. outdoor operation, license
requirements and allowed channels of operation apply in some countries as
described below.
Before operating a HiveAP, the admin or installer must properly enter the
current country code as described in Aerohive product documentation.
Note to U.S. model owners: To comply with U.S. FCC regulations, the
country selection function has been completely removed from all U.S.
models. The above function is for non-U.S. models only.
HiveAPs automatically limit the allowable channels determined by the
current country of operation. Incorrectly entering the country of operation
might result in illegal operation and cause harmful interference to other
systems. The admin is obligated to ensure HiveAPs are operating according
to the channel limitations, indoor/outdoor restrictions and license
requirements for each European Community country as described in this
section.
HiveAPs can be operated indoors or outdoors in all countries of the
European Community using the 2.4 GHz band: Channels 1-13, except where
noted below:
In Italy and Luxembourg, you must apply for a license from the national
spectrum authority to operate a HiveAP outside your own premises and
for public use or service.
In Belgium outdoor operation is only permitted using the 2.46 to 2.4835
GHz band: Channel 13.
In France outdoor operation is limited to the 2.454 to 2.4835 GHz band
(channels 8 to 13) at a maximum of 10 mW EIRP (effective isotropic
radiated power).
In Norway, the 2.4 GHz band cannot be used outdoors within a 20-km
radius of the center of Ny-Ålesund.
In Russia, the 2.4 GHz band is for indoor use only.
Because radar systems use some bands in the 5 GHz spectrum, WLAN
devices operating in these bands must use DFS (Dynamic Frequency
Selection) to detect radar activity and switch channels automatically to
avoid interfering with radar operations. For the ETSI region, the HiveAP
300 series is certified for the latest ETSI EN 301 893 v1.5.1 DFS
requirements and can use DFS channels 52 to 140 (5.26 GHz to 5.32 GHz,
and 5.5 GHz to 5.7 GHz). To comply with ETSI regulations when deploying a
HiveAP 300 series device outdoors, set the 5 GHz radio to operate on the
DFS channels and enable DFS. When deploying a HiveAP 300 series device
indoors, then the 5 GHz radio can also use channels 36 to 48 as well as the
DFS channels. The maximum transmit power for channels from 36 to 48 are
17dBm in the ETSI region. Because this maximum is enforced by HiveOS,
the HiveAP automatically limits the power to 17 dBm even if the setting is
greater than that.
The availability of some specific channels and/or operational frequency
bands are country dependent and are firmware programmed at installation
to match the intended destination. The firmware setting is accessible by
the end user. Some national restrictio
ns are noted below
:
In Italy and Luxembourg, you must apply for a license from the national
spectrum authority to operate a HiveAP outside your own premises and
for public use or service in the 5.15 to 5.35 GHz band (channels 36 to 64)
and 5.47 to 5.725 GHz band (channels 100 to 140).
In Russia, you can only use the 5.15 to 5.35 GHz band at 100 mW (20
dBm) indoors, in closed industrial and warehouse areas, and on board
aircraft for local network and crew communications during all stages of
a flight and for public WLAN access only at an altitude of 3000 meters or
higher. You can only use the 5.65 to 5.825 GHz band with 100 mW EIRP
on board aircraft at an altitude of 3000 meters or higher.
Aerohive HiveAP Compliance Information 4
© 2011 Aerohive Networks, Inc. All rights reserved. 330033-13 Rev. B
Declaration of Conformity in Languages
of the European Community
Czech Aerohive tímto prohlašuje, že tento Radio LAN device
je ve shodě se základními požadavky a dalšími
příslušnými ustanoveními směrnice 1999/5/ES.
Danish Undertegnede Aerohive erklærer herved, at følgende
udstyr Radio LAN device overholder de væsentlige krav
og øvrige relevante krav i direktiv 1999/5/EF.
Dutch Hierbij verklaart Aerohive dat het toestel Radio LAN
device in overeenstemming is met de essentiële eisen
en de andere relevante bepalingen van richtlijn
1999/5/EG.
English Hereby, Aerohive, declares that this Radio LAN device
is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
Estonian
Käesolevaga kinnitab Aerohive seadme Radio LAN
device vastavust direktiivi 1999/5/EÜ põhinõuetele ja
nimetatud direktiivist tulenevatele teistele
asjakohastele sätetele.
Finnish Valmistaja Aerohive vakuuttaa täten että Radio LAN
device tyyppinen laite on direktiivin 1999/5/EY
oleellisten vaatimusten ja sitä koskevien direktiivin
muiden ehtojen mukainen.
French Par la présente Aerohive déclare que cet appareil Radio
LAN device est conforme aux exigences essentielles et
aux autres dispositions relatives à la directive
1999/5/CE.
German Hiermit erklärt Aerohive, dass sich dieses Radio LAN
device in Übereinstimmung mit den grundlegenden
Anforderungen und den anderen relevanten
Vorschriften der Richtlinie 1999/5/EG befindet".
(BMWi)
Gree
k
Hungarian Alulírott, Aerohive nyilatkozom, hogy a Radio LAN
device megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb
elõírásainak.
Italian Con la presente Aerohive dichiara che questo Radio LAN
device è conforme ai requisiti essenziali ed alle altre
disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.
Latvian
Ar šo Aerohive deklarē, ka Radio LAN device atbilst
Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar
to saistītajiem noteikumiem.
Lithuanian
Š
iuo Aerohive deklaruoja, kad šis Radio LAN device
atitinka esminius reikalavimus ir kitas 1999/5/EB
Direktyvos nuostatas.
Maltese Hawnhekk, Aerohive, jiddikjara li dan Radio LAN device
jikkonforma mal-ħtiġijiet essenzjali u ma
provvedimenti oħrajn relevanti li hemm fid-Dirrettiva
1999/5/EC.
Polish Niniejszym Aerohive oświadcza, że Radio LAN device
jest zgodne z zasadniczymi wymogami oraz pozostałymi
stosownymi postanowieniami Dyrektywy 1999/5/EC.
Portuguese Aerohive declara que este Radio LAN device está
conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.
Slovenian
Aerohive izjavlja, da je ta Radio LAN device v skladu z
bistvenimi zahtevami in ostalimi relevantnimi določili
direktive 1999/5/ES.
Spanish
Por medio de la presente Aerohive declara que el Radio
LAN device cumple con los requisitos esenciales y
cualesquiera otras disposiciones aplicables o exigibles
de la Directiva 1999/5/CE.
Swedish
Härmed intygar Aerohive att denna Radio LAN device
står I överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som
framgår av direktiv 1999/5/EG.
HiveAP Safety Compliance
Power Cord Safety
Please read the following safety information carefully before installing a
HiveAP.
Warning: Installation and removal of HiveAPs must be carried out by qualified
personnel only.
HiveAPs must be connected to an earthed (grounded) outlet to comply
with international safety standards.
Do not connect HiveAPs to an A.C. outlet (power supply) without an earth
(ground) connection.
The appliance coupler (the connector to the unit and not the wall plug)
must have a configuration for mating with an EN 60320/IEC 320 appliance
inlet.
The socket outlet must be near the HiveAP and easily accessible. You can
only remove power from a HiveAP by disconnecting the power cord from
the outlet.
HiveAPs operate under SELV (Safety Extra Low Voltage) conditions
according to IEC 60950. The conditions are only maintained if the
equipment to which they are connected also operates under SELV
conditions.
A HiveAP receiving power through its PoE (Power over Ethernet) interface
must be in the same building as the equipment from which it receives
power.
France and Peru only:
HiveAPs cannot be powered from IT* supplies. If your supplies are of IT type,
then a HiveAP must be powered by 230 V (2P+T) via an isolation transformer
ratio 1:1, with the secondary connection point labelled Neutral, connected
directly to earth (ground). *Impédance à la terre
Important! Before making connections, make sure you have the correct cord
set. Check it (read the label on the cable) against the description in this section.
Power Cord Set
U.S.A.
and Canada
The cord set must be UL/CSA/NRTL approved and
certified.
Minimum specifications for the flexible cord:
- No. 18 AWG not longer than 2 meters, or 16 AWG
- Type SV or SJ
- 3-conductor
The cord set must have a rated current capacity of at
least 10 A.
The attachment plug must be an earth-grounding type
with NEMA 5-15P (15 A, 125 V) or NEMA 6-15 (15 A, 250
V) configuration.
Denmar
The supply plug must comply with Section 107-2-D1,
Standard DK2-1a or DK2-5a.
Switzerland
The supply plug must comply with SEV/ASE 1011.
U.K.
The supply plug must comply with BS1363 (3-pin 13 A)
and be fitted with a 5 A fuse that complies with BS1362.
The
mains
cord must be <HAR> or <BASEC> marked and
be of type HO3VVF3GO.75 (minimum).
Aerohive HiveAP Compliance Information 5
© 2011 Aerohive Networks, Inc. All rights reserved. 330033-13 Rev. B
Europe The supply plug must comply with CEE7/7 ("SCHUKO").
The mains cord must be <HAR> or <BASEC> marked and
be of
type
HO3VVF3GO.75 (minimum).
IEC-320 receptacle.
Veuillez lire attentivement les informations de sécurité relatives à l'installation
d'un point d'accès HiveAP.
Avertissement: L'installation et la dépose de points d'accès HiveAP doivent être
effectuées uniquement par un personnel qualifié.
Les points d'accès HiveAP doivent être connectés sur le secteur par une
prise électrique munie de terre (masse) afin de respecter les standards
internationaux de sécurité.
Ne jamais connecter des points d'accès HiveAP à une alimentation
électrique non-pourvue de terre (masse).
Le boitier d'alimentation (connecté directement au point d'accès) doit être
compatible avec une entrée électrique de type EN 60320/IEC 320.
La prise secteur doit se trouver à proximité du point d'accès HiveAP et
facilement accessible. Vous ne pouvez mettre hors tension un point d'accès
HiveAP qu'en débranchant son alimentation électrique au niveau de cette
prise.
Pour des raisons de sécurité, le point d'accès HiveAP fonctionne à une
tension extrêmement basse, conformément à la norme IEC 60950. Les
conditions de sécurité sont valables uniquement si l'équipement auquel le
point d'accès HiveAP est raccordé fonctionne également selon cette
norme.
Un point d'accès HiveAP alimenté par son interface réseau Ethernet en
mode POE (Power over Ethernet) doit être physiquement dans le même
bâtiment que l'équipement réseau qui lui fournit l'électricité.
France et Pérou uniquement:
Un point d'accès HiveAP ne peut pas être alimenté par un dispositif à impédance
à la terre. Si vos alimentations sont du type impédance à la terre, alors le point
d'accès HiveAP doit être alimenté par une tension de 230 V (2P+T) via un
transformateur d'isolement à rapport 1:1, avec le neutre connecté directement
à la terre (masse).
Cordon électrique - Il doit être agréé dans le pays d'utilisation
Etats-Unis
et Canada
Le cordon doit avoir reçu l'homologation des UL et un
certificat de la CSA.
Les spécifications minimales pour un cable flexible
- AWG No. 18, ou AWG No. 16 pour un cable de longueur
inférieure à 2 mètres.
- Type SV ou SJ
- 3 conducteurs
Le cordon doit être en mesure d'acheminer un courant
nominal d'au moins 10 A.
La prise femelle de branchement doit être du type à mise à
la terre (mise à la masse) et respecter la configuration
NEMA 5-15P (15 A, 125 V) ou NEMA 6-15P (15 A, 250 V).
Danemar
k
La prise mâle d'alimentation doit respecter la section 107-2
D1 de la norme DK2 1a ou DK2 5a.
Suisse La prise mâle d'alimentation doit respecter la norme
SEV/ASE 1011.
Europe La prise secteur doit être conforme aux normes CEE 7/7
("SCHUKO").
LE cordon secteur doit porter la mention <HAR> ou <BASEC>
et doit être de type HO3VVF3GO.75 (minimum).
Bitte unbedingt vor dem Einbauen des HiveAP die folgenden
Sicherheitsanweisungen durchlesen.
Warnung: Die Installation und der Ausbau des Geräts darf nur durch
Fachpersonal erfolgen.
Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose
angeschlossen werden.
Das Gerät muß an eine geerdete Steckdose angeschlossen werden, welche
die internationalen Sicherheitsnormen erfüllt.
Der Gerätestecker (der Anschluß an das Gerät, nicht der
Wandsteckdosenstecker) muß einen gemäß EN 60320/IEC 320
konfigurierten Geräteeingang haben.
Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein.
Die Stromversorgung des Geräts kann nur durch Herausziehen des
Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.
Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen
(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind nur
gegeben, wenn auch die an das Get angeschlossenen Geräte unter
SELV-Bedingungen betrieben werden.
Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft
werden:
U.S.A.
und
Kanada
Der Cord muß das UL gepruft und war das CSA beglaubigt.
Das Minimum spezifikation fur der Cord sind:
- Nu. 18 AWG - nicht mehr als 2 meter, oder 16 AWG.
- Der typ SV oder SJ
- 3-Leiter
Der Cord muß haben eine strombelastbarkeit aus wenigstens 10
A.
Dieser Stromstecker muß hat einer erdschluss mit der typ NEMA
5-15P (15A, 125V) oder NEMA 6-15P (15A, 250V) konfiguration.
Danemar
k
Dieser Stromstecker muß die ebene 107-2-D1, der standard
DK2-1a oder DK2-5a Bestimmungen einhalten.
Schweiz
Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen
einhalten.
Europe
Europe Das Netzkabel muß vom Typ HO3VVF3GO.75
(Mindestanforderung) sein und die Aufschrift <HAR> oder
<BASEC> tragen.
Der Netzstecker muß die Norm CEE 7/7 erfüllen ("SCHUKO").
HiveAP 170 Professional Installation Requirement
Please be advised that due to the unique function supplied by this product, the
device is intended for use with Aerohive software and licensed third-party
software only. The product will be distributed through controlled distribution
channels, installed by trained professionals, and will not be sold directly to the
general public through retail stores.
1. Installation personal
This product is designed for a specific application and must be installed by
qualified personnel with RF and related rule knowledge. The general user
shall not attempt to install or change the device settings.
2. Installation location
To meet regulatory RF exposure requirements, the product shall be
installed at a location where the radiating antenna in normal operating
conditions can be kept at least 20cm from people.
3. External antenna
Use only antennas which have been approved by Aerohive Networks, Inc.
Non-approved antennas may produce unwanted spurious or excessive RF
transmission, which is prohibited, and may violate the FCC/IC limit.
4. Installation procedure
Please refer to installation manual for details.
5. Warning
Please carefully select the installation position and make sure that the
final power output does not exceed the allowed limit. Violation of this
limit could lead to serious federal penalties.
Aerohive HiveAP Compliance Information 6
© 2011 Aerohive Networks, Inc. All rights reserved. 330033-13 Rev. B
HiveAP 170 Instructions d'installation professionnelle
Veuillez noter que l'appareil etant dedie a une fonction unique, il doit etre
utilise avec Aerohive logiciel proprietaire. Ce produit sera propose par un
reseau de distribution controle et installe par des professionels; il ne sera pas
propose au grand public par le reseau de la grande distribution.
1. Installation
Ce produit est destine a un usage specifique et doit etre installe par un
personnel qualifie maitrisant les radiofrequences et les regles s'y
rapportant. L'installation et les reglages ne doivent pas etre modifies par
l'utilisateur final.
2. Emplacement d'installation
En usage normal, afin de respecter les exigences reglementaires
concernant l'exposition aux radiofrequences, ce produit doit etre installe
de facon a respecter une distance de 40 cm entre l'antenne emettrice et
les personnes.
3. Antenn externe.
Utiliser uniiquement les antennes approuvees par le fabricant. L'utilisation
d'autres antennes peut conduire a un niveau de rayonnement essentiel ou
non essentiel depassant les niveaux limites definis par FCC/IC, ce qui est
interdit.
4. Procedure d'installation
Consulter le manuel d'installation.
5. Avertissement
Choisir avec soin la position d'installation et s'assurer que la puissance de
sortie ne depasse pas les limites en vigueur. La violation de cette regle
peut conduire a de serieuses penalites federales.
Korean ;
당해
무선설비는
전파혼신
가능성이
있으므로
인명안전과
관련된
서비스는
없음
Liability Disclaimer
Installation of Aerohive equipment must comply with local and national
electrical codes and with other regulations governing this type of installation.
Aerohive Networks, its channel partners, resellers, and distributors assume no
liability for personal injury, property damage, or violation of government
regulations that might arise from failing to comply with the instructions
provided and appropriate electrical codes.
Country Certification Statements
The following HiveAPs have been certified by the specified regulatory agencies
and authorities:
HiveAP 170
UAE: Telecommunication Regulatory Authority (TRA)
Registration Number: ER0077814/11
Dealer number: DA0070080/11
HiveAP 330
UAE: Telecommunication Regulatory Authority (TRA)
Registration Number: ER0072051/11
Dealer number: DA0070080/11
Mexico: Cofetel Cert. Number: NYCE/CT/0928/12/TS
China: SRRC: CMIIT: 2011AJ7102
Hong Kong: OFTA: Certificate No: HK0011200428
Chile Certificate: ORD No. 2129/DFRS04348/F-50
Saudi Arabia: Product Conformity Programme (PCP)
Registration Number: KSA R-103282
Communications &and Information Technology Commission (CITC)
Number: 20111024001
HiveAP 350
UAE: Telecommunication Regulatory Authority (TRA)
Registration Number: ER0081235/12
Dealer number: DA0070080/11
Mexico: Cofetel Cert. Number: NYCE/CT0929/12/TS
China: SRRC: CMIIT: 2011AJ7101
Saudi Arabia: Product Conformity Programme (PCP)
Registration Number: KSA R-103282
Communications &and Information Technology Commission (CITC)
Number: 20111024002
BR100:
UAE: Telecommunication Regulatory Authority (TRA)
Registration Number: ER0070180/11
Dealer number: DA0070080/11
Singapore: Complies with IDA Standards (DA…….)
Registration Number: N1671-12
BR200-WP:
UAE: Telecommunication Regulatory Authority (TRA)
Registration Number: ER0091469/12
Dealer number: DA0070080/11
Singapore: Complies with IDA Standards (DA…….)
Registration Number: N1672-12
Hong Kong: OFTA: Certificate No: HKTA0011200429
Saudi Arabia: Product Conformity Programme (PCP)
Registration Number: KSA R-103282
Communications &and Information Technology Commission (CITC)
Number: 20120902005
HiveAP 340
Saudi Arabia: Product Conformity Programme (PCP)
Registration Number: KSA R-103282
Communications & and Information Technology Commission (CITC)
Number: 14408
HiveAP 320
Mexico: Cofetel Certification Number: RCPAEHI10-1206
NYCE/NOM Certification Number: 1002CE11218
Singapore: Complies with IDA Standards (DA…..)
Registration Number: N1678-12
HiveAP 120
UAE: Telecommunication Regulatory Authority (TRA)
Registration Number: ER0070180/11
Dealer number: DA0070080/11
Malaysia: SIRIM Type Approval Code: RAVG/92M/1010/S (10-1784)
Singapore: Complies with IDA Standards (DA103787)
Registration Number: G1901-10
China: SRRC: CMIIT: 2011AJ6593
HiveAP 121
UAE: Telecommunication Regulatory Authority (TRA)
Registration Number: ER0090750/12
Dealer number: DA0070080/11
Hong Kong: OFTA: Certificate No: HK0011200429
Singapore: Complies with IDA Standards (DA103787)
Saudi Arabia: Product Conformity Programme (PCP)
Registration Number: KSA R-103282
Communications &and Information Technology Commission (CITC)
Number: 20120902007
HiveAP 141
UAE: Telecommunication Regulatory Authority (TRA)
Registration Number: ER0090748/12
Dealer number: DA0070080/11
Hong Kong: OFTA: Certificate No: HKT0011200510
Singapore: Complies with IDA Standards (DA103787)
Saudi Arabia: Product Conformity Programme (PCP)
Registration Number: KSA R-103282
Communications &and Information Technology Commission (CITC)
Number: 20120902006
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Aerohive AP370 Manuel utilisateur

Catégorie
Antennes réseau
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues