DeWalt DXCMV5048055 Manuel utilisateur

DXCMV5048055

Two Stage, Belt Drive, Electric Air Compressors

Compresseurs d’air électriques à un étage à entraînement par courroie

Compresores eléctricos de aire, de una sola etapa y accionamiento por correa

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y

PÓLIZA DE GARANTÍA. ADVERNTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-888-895-4549 • www.DEWALT.com

MAT Industries, LLC, Long Grove, IL 60047

2018 DEWALT

2

English

Air Compressor

A. Pump Air Intake Filter

B. Auto(-)/Off(O) Switch

C. Air Tank Pressure Gauge

D. Regulated Pressure Gauge

E. Pressure Regulator

F. Air Outlet

G. Safety Valve

H. Air Tank Drain Valve

I. Pump Oil Fill Plug

J. Pump Oil Drain Plug

K. Check Valve

L. Quick Connect (2)

Pump Specications

2 Cylinder

Two Stage

Oil Lubricated

Cast iron crankcase, cylinder, and head

Weight: 128 lbs. (58 kg.)

Oil Capacity: 49 oz. (1449 mL)

Specications

MODEL DXCMV5048055

WEIGHT 523 lbs. (237 kg)

HEIGHT 76.5”

WIDTH 31.5”

AIR TANK CAPACITY 80 gallons (302,8 liters)

APPROX. BLOW OFF PRESSURE

200 psi

FIG. 1

A

I

J

B

G

E

C

D

L/F

K

F

H

3

English

Hot Surfaces

FIG. 2

Denitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and pay atten-

tion to these symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY D

e

WALT TOOL, CALL US TOLL FREE AT:

1-888-895-4549

Important Safety Instructions

WARNING: Do not operate this unit until you read this

instruction manual for safety, operation and maintenance

instructions.

WARNING: CONTAINS LEAD. May be harmful if eaten or

chewed. May generate dust containing lead. Wash hands after

use. Keep out of reach of children.

WARNING: This product can expose you to chemicals

including Lead, which is known to the State of California to cause

cancer and birth defects or other reproductive harm. For more

information go to www.P65Warnings.ca.gov.

OUTLET TUBES

COMPRESSOR CYLINDER

& HEAD

PUMP

CRANKCASE

4

English

• Restricting any of the com-

pressor ventilation openings

will cause serious overheat-

ing and could cause fire.

• Never place objects against

or on top of compressor.

• Operate compressor in an

open area at least 12”

(30.5 cm) away from any wall

or obstruction that would

restrict the flow of fresh air to

the ventilation openings.

• Operate compressor in a

clean, dry well ventilated

area. Do not operate unit in

any confined area. Store

indoors.

• Unattended operation of this

product could result in per-

sonal injury or property dam-

age. To reduce the risk of

fire, do no allow the com-

pressor to operator unat-

tended

• Always remain in attendance

with the product when it is

operating.

• Always turn off and discon-

nect electrical supply from

unit when not in use.

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air directly

from your compressor is not

safe for breathing. The air

stream may contain carbon

monoxide, toxic vapors,

or solid particles from the

air tank. Breathing these

contaminants can cause

serious injury or death.

• Never use air obtained directly

from the compressor to supply

air for human consumption.

The compressor is not

equipped with suitable filters

and in-line safety equipment

for human consumption.

SAVE THESE INSTRUCTIONS

DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

• It is normal for electrical con-

tacts within the motor and

pressure switch to spark.

• Always operate the compres-

sor in a well ventilated area

free of combustible materials,

gasoline, or solvent vapors.

• If electrical sparks from com-

pressor come into contact

with flammable vapors, they

may ignite, causing fire or

explosion.

• If spraying flammable materi-

als, locate compressor at

least 20' (6.1m) away from

spray area. An additional

length of air hose may be

required.

• Store flammable materials in

a secure location away from

compressor.

5

English

• Exposure to chemicals

in dust created by

power sanding, sawing,

grinding, drilling and other

construction activities may

be harmful.

• Sprayed materials such as

paint, paint solvents, paint

remover, insecticides, weed

killers, may contain harmful

vapors and poisons.

• Work in an area with good

cross ventilation. Read and

follow the safety instructions

provided on the label or

safety data sheets for the

materials you are spraying.

Always use certified safety

equipment: NIOSH/OSHA

respiratory protection or

properly fit ting face mask

designed for use with your

specific application.

DANGER: RISK OF BURSTING

Air Tank: On February 26, 2002, the U.S. Consumer Product Safety

Commission published Release # 02-108 concerning air compres-

sor tank safety:

Air compressor receiver tanks do not have an infinite life. Tank life is

dependent upon several factors, some of which include operating

conditions, ambient conditions, proper installations, field modifica-

tions, and the level of maintenance. The exact effect of these fac-

tors on air receiver life is difficult to predict.

If proper maintenance procedures are not followed, internal corro-

sion to the inner wall of the air receiver tank can cause the air tank

to unexpectedly rupture allowing pressurized air to suddenly and

forcefully escape, posing risk of injury to consumers.

Your compressor air tank must be removed from service by the end

of the year shown on your tank warning label.

The following conditions could lead to a weakening of the air tank,

and result in a violent air tank explosion:

WHAT CAN HAPPEN HOW TO PREVENT IT

• Failure to properly drain

condensed water from air

tank, causing rust and thinning

of the steel air tank.

• Drain air tank daily or after each

use. If air tank develops a leak,

replace it immediately with

a new air tank or replace the

entire compressor.

• Modifications or attempted

repairs to the air tank.

• Never drill into, weld or make

any modifications to the air

tank or its attachments. Never

attempt to repair a damaged or

leaking air tank. Replace with a

new air tank.

• Unauthorized modifications to

the safety valve, or any other

components which control air

tank pressure.

• The air tank is designed

to withstand specific

operating pressures. Never

make adjustments or parts

substitutions to alter the factory

set operating pressures.

Attachments & Accessories:

• Exceeding the pressure rating

of air tools, spray guns, air

operated accessories, tires

and other inflatables can

cause them to explode or

fly apart, and could result in

serious injury.

• Follow the equipment

manufacturers

recommendation and never

exceed the maximum allowable

pressure rating of attachments.

Never use compressor to

inflate small low pressure

objects such as children’s toys,

footballs, basketballs, etc.

6

English

Tires:

• Over inflation of tires could

result in serious injury and

property damage.

• Use a tire pressure gauge to

check the tires pressure before

each use and while inflating

tires; see the tire sidewall for

the correct tire pressure.

NOTE: Air tanks, compressors

and similar equipment used to

inflate tires can fill small tires

very rapidly. Adjust pressure

regulator on air supply to no

more than the rating of the

tire pressure. Add air in small

increments and frequently use

the tire gauge to prevent over

inflation.

DANGER: RISK OF INJURY OR PROP ER TY DAMAGE WHEN

TRANSPORTING OR STORING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Oil can leak or spill and could

result in fire or breathing

hazard; serious injury or

death can result. Oil leaks will

damage carpet, paint or other

surfaces in vehicles or trailers.

• Always place compressor

on a protective mat when

transporting to protect against

damage to vehicle from leaks.

Remove compressor from

vehicle immediately upon

arrival at your destination.

Always keep compressor level

and never lie on its side.

WARNING: RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air stream

can cause soft tissue damage

to exposed skin and can

propel dirt, chips, loose

particles and small objects

at high speed, resulting in

property damage or personal

injury.

• Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

• Never point any nozzle or

sprayer toward any part of

the body or at other people or

animals.

• Always turn the compressor

off and bleed pressure from

the air hose and air tank before

attempting maintenance,

attaching tools or accessories.

7

English

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Touching exposed metal such

as the compressor head or

outlet tubes, can result in

serious burns.

• Never touch any exposed

metal parts on compressor

during or immediately after

operation. Compressor will

remain hot for several minutes

after operation

• Do not reach around

protective shrouds or attempt

maintenance until unit has

been allowed to cool.

WARNING: RISK OF ELECTRICAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Your compressor is powered

by electricity. Like any other

electrically powered device,

if it is not used properly it

may cause electric shock.

• Never operate the compres-

sor outdoors when it is rain-

ing or in wet conditions.

• Never operate compres-

sor with protective covers

removed or damaged.

• Repairs attempted by

unqualified personnel can

result in serious injury or

death by electrocution.

• Any electrical wiring or

repairs required on this

product should be per-

formed by authorized ser-

vice center personnel in

accordance with national

and local electrical codes.

• Electrical Grounding:

Failure to provide adequate

grounding to this product

could result in serious injury

or death from electrocu-

tion. Refer to Grounding

Instructions paragraph in

the Installation section.

• Make certain that the elec-

trical circuit to which the

compressor is connected

provides proper electrical

grounding, correct voltage

and adequate fuse protection.

8

English

WARNING: RISK FROM MOVING PARTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Moving parts such as the

pulley, flywheel, and belt can

cause serious injury if they

come into contact with you or

your clothing.

• Never operate the compressor

with guards or covers which are

damaged or removed.

• Keep your hair, clothing and

gloves away from moving parts.

Loose clothes, jewelry or long

hair can be caught in moving

parts.

• Air vents may cover moving

parts and should be avoided as

well.

• Attempting to operate

compressor with damaged or

missing parts or attempting

to repair compressor with

protective shrouds removed

can expose you to moving

parts and can result in serious

injury.

• Any repairs required on this

product should be performed

by a D

eWALT factory service

center or a D

eWALT authorized

service center.

WARNING: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafe op er a tion of your air

compressor could lead to se ri-

ous in ju ry or death to you or

others.

• Review and understand all

instructions and warnings in

this manual.

• Be come fa mil iar with the op er-

a tion and con trols of the air

compressor.

• Keep operating area clear of all

persons, pets, and obstacles.

• Keep chil dren away from the air

compressor at all times.

• Do not operate the product

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

• Never defeat the safety fea tures

of this prod uct.

• Equip area of operation with a

fire extinguisher.

• Do not op er ate machine with

missing, broken, or un au tho-

rized parts.

• Never stand on the

compressor.

9

English

WARNING: RISK OF

INJURY FROM LIFTING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Serious injury can result from

attempting to lift too heavy an

object.

• The compressor is too heavy

to be lifted by one person.

Obtain assistance from others

before lifting.

CAUTION: RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Under some conditions and

duration of use, noise from

this product may contribute to

hearing loss.

• Always wear certified safety

equipment: ANSI S12.6

(S3.19) hearing protection.

SAVE THESE INSTRUCTIONS FOR FUTURE

USE

Know Your Air Compressor

READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE

OPERATING YOUR UNIT. Compare the illustrations with your

unit to familiarize yourself with the location of various controls

and adjustments. Save this manual for future reference.

FEATURES

AUTO (-) / OFF (O) SWITCH

Place this switch (B) in the AUTO (-) position to

provide automatic power to the pressure switch

and OFF(O) to remove power at the end of each

use. NOTE: ALWAYS ensure the switch (B) is in the

OFF (O) position before removing or replacing

pressure switch cover.

PRESSURE SWITCH

The pressure switch (B) automatically starts the motor when the air

tank pressure drops below the factory set cut-in pressure. It stops

the motor when the air tank pressure reaches the factory set cut-out

pressure.

SAFETY VALVE

This valve (G) is designed to prevent system

G

failures by relieving pressure from the system

when the compressed air reaches a predeter-

mined level. The valve is preset by the manu-

facturer and must not be removed or modified

in any way.

CHECK VALVE

When the air compressor is operating, the

check valve (K) is open, allowing compressed

air to enter the air tank. When the air compressor

B

K

10

English

reaches cut-out pressure, the check valve closes, allowing air

pressure to remain inside the air tank.

AIR INTAKE FILTER

The filter (A) is designed to clean air entering the

A

pump. To ensure the pump continually receives a

clean, cool, and dry air supply the filter must always

be clean and the filter intake must be free from

obstructions.

AIR TANK DRAIN VALVE

The drain valve (H) is located at the base of

the air tank and is used to drain

condensation at the end of each use. See

Draining Air Tank under Maintenance.

REGULATED PRESSURE GAUGE

The regulated pressure gauge (D) indicates the

G C

E

D L

air pressure available at the outlet side of the

regulator. This pressure is controlled by the

regulator and is always less or equal to the air

tank pressure.

TANK PRESSURE GAUGE

The tank pressure gauge (C) indicates the

reserve air pressure in the tank.

UNIVERSAL QUICK CONNECT BODY

The universal quick connect body (L) accepts the three most popular

styles of quick connect plugs: Industrial, automotive, and ARO. One

hand push-to-connect operation makes connections simple and easy.

REGULATOR

The regulator knob (E) controls the air pressure coming from the air

tank.

To Adjust Regulator:

1. Pull regulator knob (E) out.

2. Turn knob clockwise to increase regulated pressure and

counter-clockwise to decrease regulated pressure.

3. When desired pressure is shown on the regulated pressure

gauge push knob in to lock.

WARNING: Risk of Bursting. Too much air pressure causes

a hazardous risk of bursting. Check the manufacturer’s

maximum pressure rating for air tools and accessories. The

regulator outlet pressure must never exceed the maximum

pressure rating.

GLOBE VALVE/AIR DISCHARGE VALVE: (sold separately, not

shown)

Opens and closes air distribution from compressor. See Air

Distribution System paragraph under Installation.

REGULATOR (sold separately, not shown):

An air pressure regulator or a separate air transformer which

combines the functions of air regulation and/or moisture and

dirt removal is recommended for most applications. See Air

Distribution System paragraph under Installation.

AIR COMPRESSOR PUMP

The pump compresses air into the air tank. Working air is not available

until the compressor has raised the air tank pressure above that

required at the air outlet.

MOTOR OVERLOAD PROTECTOR

The motor has a thermal overload protector.

M

If the motor overheats for any reason, the

overload protector will shut off the motor. The

motor must be allowed to cool down before

H

11

English

restarting. To restart:

1. Set the Auto/Off switch to OFF (O).

2. Allow the motor to cool.

3. Depress the red reset button (M) on the motor.

4. Set the Auto/Off switch to AUTO (-).

INSTALLATION

Assembly (Fig. 1)

Unpack the air compressor. Inspect the unit for damage. If the

unit has been damaged in transit, contact the carrier and

complete a damage claim. Do this immediately because there

are time limitations to damage claims.

The carton should contain:

• air compressor

• operator and parts manuals

Check the compressor’s serial label to ensure that you have

received the model ordered, and that it has the required pressure

rating for its intended use.

INSTALLING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in

hand when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 psi.

2. Apply sealant tape to hose threads.

3. Assemble hose to air outlet (F). IMPORTANT: Do not assemble

splitters directly to the air outlet (F).

NOTE: Assembling quick connect bodies (L) to air outlet (F)

and quick connect plugs to hose ends make connecting and

disconnecting hoses simple and easy. Quick connect bodies

and plugs are available for purchase from your local dealer or

authorized service center.

DISCONNECTING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in

hand when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 psi.

2. Remove hose from air outlet (F).

Lubrication and Oil

AIR COMPRESSOR

The air compressor pump was filled WITH oil at the manufacturer.

Check air compressor pump oil level before operating unit. See

Compressor Pump Oil under Maintenance.

Compatibility

Air tools and accessories that are run off the compressor must be

compatible with petroleum based products. If you suspect that a

material is not compatible with petroleum products, an air line filter

for removal of moisture and oil vapor in compressed air is required.

NOTE: Always use an air line filter to remove moisture and oil vapor

when spraying paint.

Location

• Locate the air compressor in a clean, dry, and well ventilated

area.

• Located the air compressor at least 12” (30.5 cm) away from

the wall or other obstructions that will interfere with the flow of

air.

• Locate the air compressor as close to the main power supply

as possible to avoid using long lengths of electrical wiring.

NOTE: Long lengths of electrical wiring could cause power loss

to the motor.

12

English

• The air filter must be kept clear of obstructions which could

reduce air flow to the air compressor.

HUMID AREAS

In frequently humid areas, moisture may form in the pump and

produce sludge in the oil, causing running parts to wear out

prematurely. Excessive moisture is especially likely to occur if

the unit is located in an unheated area that is subject to large

temperature changes. Two signs of excessive humidity are external

condensation on the pump when it cools down and a “milky”

appearance in compressor oil. You may be able to prevent

moisture from forming in the pump by increasing ventilation or

operating for longer intervals.

NOISE CONSIDERATIONS

Consult local officials for information regarding acceptable

noise levels in your area. To reduce excessive noise, use

vibration mounts or silencers, relocate the unit or construct total

enclosures or baffle walls. Contact a D

e

WALT service center or

call 1-888-895

-

4549 for assistance.

Anchoring of the Air Compressor

WARNING: Risk of bursting. Excessive vibration can weaken

the air tank and cause an explosion. The compressor must be

properly mounted.

The air compressor MUST be bolted to a level, solid concrete

surface. Use 3/8” lag screws, vibration pads and concrete

anchors. If help is needed anchoring the air compressor consult

a licensed contractor.

1. Place the air compressor on a level, solid concrete surface.

Make sure the concrete is in good condition with no cracks

or damage.

2. Mark the surface

3/8" Lag

Screw

(not supplied)

Vibration

pad

(not

supplied)

Concrete Anchor

(not supplied)

Surface Line

Shim Under

Vibration pad

(not supplied)

using the holes in

the air compressor

feet as a template.

3. Drill holes in the

surface for the

concrete anchors.

Install concrete

anchors.

4. Line-up holes in

surface with holes in

air compressor feet.

5. Place the vibration pads (not supplied) between the floor and

air compressor feet, see figure. If needed use shims to level

the unit.

6. Place the 3/8” lag screws through the air compressor feet,

vibration pads and into the anchors.

7. Torque 3/8” lag screws to 7-10 ft.-lbs (9.5-13.5 Nm).

Wiring Instructions

WARNING: Improper electrical installation of this product

may void its warranty and your fire insurance. Have circuit wiring

performed by qualified personnel such as a licensed electrician

who is familiar with the current national electrical code and any

prevailing local electrical codes.

WARNING: Risk of electrical shock. Improper electrical

grounding can result in electrical shock. The wiring should be

done by a qualified electrician.

A qualified electrician needs to knows the following before wiring:

1. The amperage rating of the electrical box should be adequate.

13

English

Refer to the Specifications, in the parts manual, for this

information.

2. The supply line should have the same electrical characteristics

(voltage, cycle, phase) as the motor. Refer to the motor

nameplate, on side of motor, for this information.

NOTE: The wiring used must be rated for the motor nameplate

voltage, plus or minus 10%. Refer to local codes for recommended

wire sizes, correct wire size, and maximum wire run; undersize wire

causes high amp draw and overheating to the motor.

WARNING: Risk of electrical shock. Electrical wiring must

be located away from hot surfaces such as manifold assembly,

compressor outlet tubes, heads, or cylinders.

Grounding Instructions

This product should be connected to a metallic, permanent wiring

system, of and equipment-grounding terminal or lead on the

product.

Voltage and Circuit Protection

Refer to the Voltage and Minimum Branch Circuit Requirements

under Specifications.

CAUTION: Certain air compressors can be operated on a

15 amp circuit if the following conditions are met.

• Voltage supply to circuit must comply with the National

Electrical Code.

• Circuit is not used to supply any other electrical needs.

• Extension cords comply with specifications.

• Circuit is equipped with a 15 amp circuit breaker or 15 amp

time delay fuse. NOTE: If compressor is connected to a cir-

cuit protected by fuses, use only time delay fuses. Time delay

fuses should be marked “D” in Canada and “T” in the U.S.

If any of the above conditions cannot be met, or if operation of the

compressor repeatedly causes interruption of the power, it may be

necessary to operate it from a 20 amp circuit. It is not necessary to

change the cord set.

Main power disconnect switch

Install a main power disconnect switch in the line from the panel

to the compressor. The main power disconnect switch must be

located near the compressor, for ease of use and safety. When

turned OFF, the main power disconnect switch shuts off all power

to the compressor. When it is turned ON, the compressor will

start and stop automatically, controlled by the pressure switch.

Air Distribution System

WARNING: Risk of bursting. Plastic or PVC pipe is not

designed for use with compressed air. Regardless of its indicated

pressure rating, plastic pipe can burst from air pressure. Use only

metal pipe for air distribution lines.

INSTALLING AND DISCONNECTING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip. Ensure

regulated pressure gauge reads 0 psi.

The next figure represents a typical air distribution system.

The following are tips to remember when setting up the air

compressor’s air distribution system.

NOTE: Compressed air from oil lube air compressors will contain

wa ter condensation and oil mist. Several drains, traps and filters

will be needed to supply air without water (including aerosols) or oil

to spray equipment, air tools and accessories requiring filtered air.

Always read the in struc tions for the air tools and accessories being

used.

14

English

• Use pipe that is the same size as the air tank outlet. Piping that

is too small will restrict the flow of air.

• If piping is over 100’ (30.5m) long, use the next larger size.

• Bury underground lines below the frost line and avoid pockets

where condensation can gather and freeze. Apply pressure

before underground lines are covered to make sure all pipe

joints are free of leaks.

• A flexible coupling is recommended to be installed between

the globe valve/air discharge outlet and main air distribution

line to allow for vibration.

• A separate regulator is recommended to control the air

pressure. Air pressure from the tank is usually too high for

individual air driven tools.

• DO NOT install lubricators between the tank and any spray

equipment, air tool or accessory requiring oil-free filtered air.

• Drain all traps, filters and dirt legs daily.

SPR AY

GUN

AIR

TOOL

DRAIN

LEGS

FI LTER /

MOISTURE

TRAP

DIRT

LEGS

DRAIN

VALVES

DRAIN

VALVE

LUBRIC ATOR

REGUL ATOR

GLOBE VALVE /

AIR DISCHARGE

VALVE

MAIN DISTRIBUTION AIR LINES

Slope pipe in di rection of air o w.

Water condensate ows along

bottom of pipe to drain legs,

preventing it f rom entering feeder

lines.

REGUL ATOR

BALL

FI LTER

FLEXIBLE

COUPLING

DRAIN

VALVE

TYPICAL

COMPRESSED AIR

DISTRIBUTION

SYSTEM

AIR FLOW

FEEDER LINES SLOPE

WITH AIR FLOW

AIR USAGE

LINES

AIR

COMPRESSOR

FI LTER /

MOISTURE

TRAP

FOR BEST PERFORMANCE

the distance between the

comp ressor and the

moistu re trap should be as

long as possible

DRAIN

VALVES

5 MICRON

FI LTER

.01 MICRON

FI LTER

RISK OF BURSTING. ALWAYS USE

METAL PIPING AND FITTINGS.

How to Use Your Unit (Fig 3)

How to Stop:

Set the Auto/Off switch to “Off”.

Before Starting

WARNING: Do not operate this unit until you read this instruction

15

English

manual for safety, operation and maintenance instructions.

Break-in Procedure

NOTICE: Risk of property damage. Serious damage may result if

the following break-in instructions are not closely followed.

This procedure is required before the air compressor is put into

service and when the check valve or a complete compressor pump

has been replaced.

1. Make sure the Auto/Off switch is in the “Off” position.

2. Check oil level in pump. See Oil paragraph in the Maintenance

section for instructions.

3. Recheck all wiring. Make sure wires are secure at all terminals

connections. Make sure all contacts move freely and are not

obstructed.

4. Open the drain valve (counterclockwise) fully to permit air to

escape and prevent air pressure build up in the air tank during

the break-in period.

5. Move the Auto/Off switch to “Auto” position. The compressor

will start.

6. Run the compressor for 30 minutes. Make sure the drain valve

and all air lines are open so there is only a minimal air pressure

build-up in tank.

NOTE: After about 30 minutes, If the unit does not operate

properly, SHUT DOWN IMMEDIATELY, and contact Product

Service.

7. Check all air line fittings and connections/piping for air leaks

by applying a soap solution. Correct if necessary. NOTE: Minor

leaks can cause the air compressor to overwork, resulting in

premature breakdown or inadequate performance.

8. Check for excessive vibration. Readjust or shim air compressor

feet, if necessary.

9. After 30 minutes, turn the Auto/Off switch to the “Off” position.

10. Close the drain valve.

11. Turn the Auto/Off switch to the “Auto” position. The air receiver

will fill to “cut-out” pressure and the motor will stop.

The compressor is now ready for use.

Before Each Start-Up

1. Place Auto/Off switch to “Off”.

2. Close the drain valve.

3. Visually inspect air lines and fittings for leaks.

4. Check safety valve. See To Check Safety Valve under

Maintenance.

5. Pull the regulator knob out and turn counterclockwise to set

the outlet pressure to zero.

6. Attach hose and accessories.

WARNING: Risk of unsafe operation. Firmly grasp air hose

in hand when installing or disconnecting to prevent hose whip.

WARNING: Risk of unsafe operation. Do not use damaged or

worn accessories.

NOTE: A regulator MUST be installed when using accessories

rated at less than 135 psi.

NOTE: The hose or accessory will require a quick connect plug if

the air outlet is equipped with a quick connect socket.

WARNING: Risk of bursting. Too much air pressure causes a

hazardous risk of bursting. Check the manufacturer’s maximum

pressure rating for air tools and accessories. The regulator outlet

pressure must never exceed the maximum pressure rating.

CAUTION: Risk of unsafe operation. Compressed air from the

16

English

unit may contain wa ter condensation and oil mist. Do not spray

un fil tered air at an item that could be damaged by moisture.

Some air tools and accessories may require filtered air. Read the

in struc tions for the air tools and accessories.

How to Start

1. Turn the Auto/Off switch to “Auto” and allow tank pressure to

build. Motor will stop when tank pressure reaches “cut-out”

pressure.

2. Pull the regulator knob out and turn clockwise to increase pres-

sure. When the desired pressure is reached push knob in to

lock in place.

IMPORTANT: When using regulator and other accessories refer to

the manufacturers instructions.

WARNING: Risk of bursting. If any unusual noise or vibration

is noticed, stop the compressor immediately and have it checked

by a trained service technician.

The compressor is ready for use.

Shut-down (Fig. 1)

1. Move Auto/Off switch to the OFF position. NOTE: If finished

using compressor, follow Steps 2 - 6.

2. Pull the regulator knob out and turn counterclockwise until fully

closed. Ensure regulated pressure gauge reads 0 psi. Push

knob in to lock in place.

3. Remove hose and accessory.

WARNING: Risk of unsafe operation. Firmly grasp air hose in

hand when installing or disconnecting to prevent hose whip.

4. Drain the air tank,

see Draining Air Tank under Maintenance

.

Ensure air tank pressure gauge reads 0 psi.

WARNING: Risk of bursting. Drain air tank daily. Water will

condense in air tank. If not drained, water will corrode and

weaken the air tank causing a risk of air tank rupture.

5. Allow the compressor to cool down.

6. Wipe air compressor clean and store in a safe, non-freezing

area.

OPEN

CLOSE

FIG. 3

OFF

AUTO

17

English

MAINTENANCE

Maintenance Chart

Procedure

Daily

Weekly

Monthly

or every

50 Hours

1 year

or 200

Hours

See tank

warning

label

Check safety valve

X

Inspect air filter

X

+

Drain air tank

X

Check pump oil level

X

Change pump oil

X

**

+

Oil leak inspection

X

Inspect drive belt

X

Check drive belt tension

X

Check pulley/flywheel alignment

X

Check for unusual noise/vibration

X

Check for air leaks

X*

Clean compressor exterior

X

Remove tank from service

X

++

* To check for air leaks apply a solution of soapy water around joints.

While compressor is pumping to pressure and after pressure cuts out,

look for air bubbles to form.

** The pump oil must be changed after the first 20 hours or operation.

Thereafter, when using full

synth

etic non-detergent air compressor

oil, change oil every 200 hours of operation or once a year, whichever

comes first.

+ Perform more frequent in dusty or humid conditions.

++

For more information, call 1-888-895-4549 .

WARNING: Risk of unsafe operation. Unit cycles automati-

cally when power is on. When performing maintenance, you may

be exposed to voltage sources, compressed air, or moving parts.

Personal injuries can occur. Before performing any maintenance

or repair, disconnect power source from the compressor and

bleed off all air pressure.

To ensure efficient operation and longer life of the air compressor

outfit, a routine maintenance schedule should be prepared and fol-

lowed. The following routine maintenance schedule is geared to an

outfit in a normal working environment operating on a daily basis.

If necessary, the schedule should be modified to suit the condi-

tions under which your compressor is used. The modifications will

depend upon the hours of operation and the working environment.

Compressor outfits in an extremely dirty and/or hostile environment

will require a greater frequency of all maintenance checks.

NOTE: See Operation section for the location of controls.

Checking Safety Valve (Fig. 1)

WARNING: Hot surfaces. Risk of burn. Tubes, pump head,

and surrounding parts are very hot, do not touch (see the Hot

Surfaces identified in Fig. 2). Allow compressor to cool prior to

servicing.

WARNING: Risk of bursting. If the safety valve does not work

properly, over-pressurization may occur, causing air tank rupture or

an explosion.

WARNING: Risk from flying objects. Always wear certified

safety equipment: ANSI Z87.1 eye protection (CAN/CSA Z94.3)

with side shields.

Before starting compressor, pull the ring on the safety valve to

make sure that the safety valve operates freely. If the valve is stuck

or does not operate smoothly, it must be replaced with the same

18

English

type of valve.

Checking Air Filter (Fig. 1)

WARNING: Hot surfaces. Risk of burn. Tubes, pump head,

and surrounding parts are very hot, do not touch (see the Hot

Surfaces identified in Fig. 2). Allow compressor to cool prior to

servicing.

A dirty air filter will not allow the compressor to operate at full

capacity. Keep the air filter clean at all times.

1. Ensure Auto/Off switch (B) is in the OFF Position.

2. Allow unit to cool.

3. Remove the wing nut (N).

4. Remove the outer metal cover

N

O

P

(O).

5. Check the filter element (P) if it is

dirty or filled with paint, replace

it.

6. Place the outer metal cover back

over the filter element.

7. Secure with the wing nut.

CAUTION: Risk of unsafe operation. Do not operate without air

filter.

Draining Air Tank (Fig. 3)

WARNING: Risk of unsafe operation. Air tanks contain high

pressure air. Keep face and other body parts away from outlet

of drain. Use eye protection [ANSI Z87.1 (CAN/CSA Z94.3)] when

draining as debris can be kicked up into face.

WARNING: Risk from noise. Use ear protection (ANSI S12.6

(S3.19) as air flow noise is loud when draining.

NOTE: All compressed air systems generate condensation that accu-

mulates in any drain point (e.g., tanks, filter, aftercoolers, dryers). This

condensate contains lubricating oil and/or substances which may be

regulated and must be disposed of in accordance with local, state,

and federal laws and regulations.

1. Set the Auto/Off switch to “Off”.

2. Pull the regulator knob out and turn counterclockwise to set

the outlet pressure to zero.

3. Remove the air tool or accessory.

4. Pull ring on safety valve allowing air to bleed from the tank until

tank pressure is approximately 20 psi. Release safety valve

ring.

5. Drain water from air tank by opening drain valve (counterclock-

wise) on bottom of tank.

WARNING: Risk of bursting. Water will condense in the air

tank. If not drained, water will corrode and weaken the air tank

causing a risk of air tank rupture.

NOTICE: Risk of property damage. Drain water from air tank may

contain oil and rust which can cause stains.

6. After the water has been drained, close the drain valve (clock-

wise). The air compressor can now be stored.

NOTE: If drain valve is plugged, release all air pressure. The valve

can then be removed, cleaned, then reinstalled.

Compressor Pump Oil (Fig. 4)

NOTICE: Risk of property damage. Use air compressor oil only.

Multi-weight automotive engine oils like 10W30 should not be used

in air compressors. They leave carbon deposits on critical compo-

nents, thus reducing performance and compressor life.

NOTE: Use full synthetic non-detergent air compressor oil.

19

English

NOTE: Crankcase oil capacity is approximately 49 fluid ounces

(1449 ml).

Checking

1. The oil level should be to the middle of the sight glass (S).

2. If needed remove oil fill plug (Q) and slowly add oil until it

reaches the middle of the sight glass.

Changing

WARNING: Drain tank to release air pressure before removing

the oil fill cap or oil drain plug.

1. Remove the oil fill plug (Q).

2. Remove the oil drain plug (R) and drain oil into a suitable con-

tainer.

3. Replace the oil drain plug (R) and tighten securely

4. Slowly add compressor oil until it reaches the middle of the

sight glass (S). NOTE: When filling the crankcase, the oil

flows very slowly into the pump. If the oil is added too quickly,

it will overflow and appear to be full.

CAUTION: Overfilling with oil will cause premature compres-

sor failure. Do not overfill.

5. Replace oil fill plug (Q) and tighten securely.

T = Full

U = Add

R = Oil drain plug

S = Oil level sight glass

Q = Oil fill plug

Fig. 4

R

Q

S

U

T

Belt Replacement

WARNING: This unit starts automatically. ALWAYS shut off

the main power disconnect, and bleed all pressure from

the system before servicing the compressor, and when the

compressor is not in use. Do not use the unit with the shrouds

or belt guard removed. Serious injury could occur from

contact with moving parts. Hot surfaces. Risk of burn. Pump

head, and surrounding parts are very hot, do not touch (see

the Hot Surfaces identified in Fig. 2). Allow compressor to

cool prior to servicing.

1. Set the Auto/Off lever to “Off”, shut off the main power discon-

nect, and relieve all air pressure from the air tank.

2. Remove the front of the beltguard by removing the

20

English

screws (V) using a Torx T25 bit.

3. Mark pump position on saddle.

4. Loosen the motor

V

mounting screws and

slide the motor toward

the air compressor.

5. Remove the belt and

replace with a new

one.

6. See the Adjusting

Belt Tension before

tightening motor

mounting screws.

Adjusting Belt Tension

1. Slide motor into original position, line the motor up with the

mark made earlier on saddle.

2. Tighten two outside

Downward Force

Deflection

motor mounting

screws enough to

hold the motor in

place for checking

pulley and flywheel

alignment.

3. The belt should

deflect 1/2” (13mm)

at midway between

the pulley and the

flywheel when a 10

pound (4.6kg.) weight is applied at the midway point.

3. When proper belt tension is achieved, tighten

all four motor mounting screws. Torque to 20-25 ft-lbs

(27.1–33.9 Nm).

NOTE: Once the engine pulley has been moved from its factory set

location, the grooves of the flywheel and pulley must be aligned

to within 1/16” (1.6mm) to prevent excessive belt wear. Verify the

alignment by performing the following Motor Pulley/Flywheel -

Alignment.

Motor Pulley/Flywheel Alignment

NOTE: Once the motor pulley has been moved from its factory set

location, the grooves of the flywheel and pulley must be aligned to

within 1/16” (1.6 mm) to prevent excessive belt wear.

The air compressor flywheel and motor pulley must be in-line (in the

same plane) within 1/16” (1.6 mm) to assure belt retention within

flywheel belt grooves. To check alignment, perform the following

steps:

1. Set the Auto/Off lever to “Off”, shut off the main power discon-

nect, and relieve all air pressure from the air tank.

2. Remove belt guard.

3. Place a straightedge

against the outside of

the flywheel and the

motor drive pulley.

4. Measure the distance

between the edge of

the belt and the straightedge at points A1 and A2 in figure. The

difference between measurements should be no more than

1/16” (1.6 mm).

5. If the difference is greater than 1/16” (1.6 mm) loosen the set

screw holding the motor drive pulley to the shaft and adjust

the pulley’s position on the shaft until the A1 and A2 measure-

ments are within 1/16” (1.6 mm) of each other.

6. Tighten the motor drive pulley set screw.

La page charge ...

DeWalt DXCMV5048055 Manuel utilisateur

DeWalt DXCMV5048055 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents