Craftsman CMXECXM601 Manuel utilisateur

Catégorie
Compresseurs d'air
Taper
Manuel utilisateur
final page size: 8.5 x 5.5 in CRAFTSMAN
Air Compressor
Compresor de aire
Compresseur d’air
CMXECXM601
INSTRUCTION MANUAL | GUIDE D’UTILISATION | MANUAL DE INSTRUCTIONES
E113085 September 2020
POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.
SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.
1-888-331-4569
WWW.CRAFTSMAN.COM
IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.
English 1
Français 17
Español 33
ENGLISH
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk
of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in .
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in .
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in .
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in
.
Hot Surfaces Compressor Pump
9
8
10
6
7
Fig. A
16
15
14
13
11
12
4
5
1
3
2
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
WARNING: Never modify the product or any part of
it. Damage or personal injury could result.
WARNING: To reduce the risk of injury, read the
instruction manual.
If you have any questions or comments about this
or any product, call CRAFTSMAN toll free at:
1-888-331-4569
Components
Auto/Off Switch
Pressure Switch (not shown)
Safety Valve
Tank Pressure Gauge
Check Valve
Air Intake Filter
Air Compressor Pump
Drain Valve
Air Outlet
Motor Overload Protector
Compressor Pump Head
Compressor Pump Cylinder
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Outlet Tube
Oil Fill Plug
Oil Sight Glass
Oil Drain Plug
CAUTION
1
ENGLISH
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk
of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in .
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in .
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in .
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in
.
Hot Surfaces Compressor Pump
9
8
10
6
7
Fig. A
16
15
14
13
11
12
4
5
1
3
2
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
WARNING: Never modify the product or any part of
it. Damage or personal injury could result.
WARNING: To reduce the risk of injury, read the
instruction manual.
If you have any questions or comments about this
or any product, call CRAFTSMAN toll free at:
1-888-331-4569
Components
Auto/Off Switch
Pressure Switch (not shown)
Safety Valve
Tank Pressure Gauge
Check Valve
Air Intake Filter
Air Compressor Pump
Drain Valve
Air Outlet
Motor Overload Protector
Compressor Pump Head
Compressor Pump Cylinder
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Outlet Tube
Oil Fill Plug
Oil Sight Glass
Oil Drain Plug
CAUTION
2
ENGLISH
Air Compressor
CMXECXM601
SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE
REFERENCE
DANGER: RISK OF EXPLOSION OR FIRE
What can happen How to prevent it
It is normal for electrical contacts
within the motor and pressure
switch to spark.
Always operate the compressor
in a well ventilated area free of
combustible materials, gasoline, or
solvent vapors.
If electrical sparks from compressor
come into contact with flammable
vapors, they may ignite, causing
fire or explosion.
If spraying flammable materials,
locate compressor at least 20 feet
(6.1 m) away from spray area.
An additional length of hose may
be required.
Store flammable materials
in a secure location away
from compressor.
Restricting any of the compressor
ventilation openings will cause
serious overheating and could
cause a fire.
Never place objects against or on
top of compressor pump.
Operate compressor in an open
area at least 12" (30.5 cm) away
from any wall or obstruction that
would r
estrict the flow of fresh air
to the ventilation openings.
Operate compressor in a clean,
dry well ventilated area. Do not
operate unit indoors or in any
confined area.
Unattended operation of this
product could result in personal
injury or property damage.
To reduce the risk of fire, do
not allow the compressor to
operate unattended.
Always remain in attendance with
the product when it is operating.
Always turn off and unplug unit
when not in use.
CAUTION: RISK FROM NOISE
What can happen How to prevent it
Under some conditions and
duration of use, noise from
this product may contribute to
hearing loss.
Always wear certified safety
equipment: ANSI S12.6 (S3.19)
hearing protection.
DANGER: RISK TO BREATHING
(Asphyxiation)
What can happen How to prevent it
The compressed air directly from
your compressor is not safe for
breathing. The air stream may
contain carbon monoxide, toxic
vapors, or solid particles from
the air tank. Breathing these
contaminants can cause serious
injury or death.
Air obtained directly from the
compressor should never be
used to supply air for human
consumption. In order to use air
produced by this compressor for
breathing, suitablelters and
in-line safety equipment must be
properly installed. In-line filters
and safety equipment used in
conjunction with the compressor
must be capable of treating air
to all applicable local and federal
codes prior to human consumption.
Exposure to chemicals in dust
created by power sanding,
sawing, grinding, drilling, and
other construction activities may
be harmful.
Work
in an area with good
ventilation. Read and follow the
safety instructions provided on the
label or safety data sheets for the
materials you are spraying. Always
use certified safety equipment:
OSHA/MSHA/NIOSH respiratory
protection designed for use with
your specific application.
Sprayed materials such as paint,
paint solvents, paint remover,
insecticides, weed killers,
may contain harmful vapors
and poisons.
WARNING: RISK OF BURSTING
Air Tank:
On February 26, 2002, the U.S. Consumer
Product Safety Commission published Release # 02-108
concerning air compressor tank safety:
Air compressor receiver tanks do not have an infinite
life. Tank life is dependent upon several factors, some of
which include operating conditions, ambient conditions,
proper installations, field modifications, and the level
of maintenance. The exact effect of these factors on air
If proper maintenance procedures are not followed,
internal corrosion to the inner wall of the air receiver tank
can cause the air tank to unexpectedly rupture allowing
pressurized air to suddenly and forcefully escape, posing
Your compressor air tank must be removed from service
The following conditions could lead to a weakening of the
air tank, and result in a violent air tank explosion:
WARNING:
CONTAINS LEAD. May be harmful if eaten or
chewed. May generate dust containing lead.
Wash hands after use. Keep out of reach of children
WARNING:
This product can expose you to chemicals
including lead, which is known to the State of
California to cause cancer and birth defects
or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
ENGLISH
What can happen How to prevent it
Failure to properly drain condensed
water from air tank causes rust
and thinning of the steel air tank.
Drain air tank daily or after each
use. If air tank develops a leak,
replace it immediately with
a new air tank or replace the
entire compressor.
Modifications or attempted repairs
to the air tank.
Never drill into, weld, or make
any modifications to the air tank
or its attachments. Never attempt
to repair a damaged or leaking air
tank. Replace with a new air tank.
Unauthorized modifications to
the safety valve or any other
components which control air
tank pressure.
The air tank is designed to
withstand specific operating
pressures. Never make adjustments
or parts substitutions to alter the
factory set operating pressures.
Attachments & accessories:
Exceeding
the pressure rating of
air tools, spray guns, air operated
accessories, tires, and other
inflatables can cause them to
explode or fly apart, and could
result in serious injury.
Follow the equipment
manufacturers recommendation
and never exceed the maximum
allowable pressure rating of
attachments. Never use compressor
to inflate small low pressure
objects such as children’s toys,
footballs, basketballs, etc.
Tires:
Over inflation of tires could
result in serious injury and
property damage.
Use a tire pressure gauge to check
the tires pressure before each
use and while inflating tires; see
the tire sidewall for the correct
tire pressure.
NOTE: Air tanks, compressors and
similar equipment used to inflate
tires can ll small tires similar to
these very rapidly. Adjust pressure
regulator on air
supply to no more
than the rating of the tire pressure.
Add air in small increments and
frequently use the tire gauge to
prevent over inflation.
WARNING: RISK OF ELECTRICAL SHOCK
What can happen How to prevent it
Your air compressor is powered
by electricity. Like any other
electrically powered device, If it
is not used properly it may cause
electric shock.
Never operate the compressor
outdoors when it is raining or in
wet conditions.
Never operate compressor with
protective covers removed
or damaged.
Repairs attempted by unqualified
personnel can result in serious
injury or death by electrocution.
Any repairs required on this
product should be performed
by authorized service
center personnel.
Electrical Grounding: Failure
to provide adequate grounding to
this product could result in serious
injury or death from electrocution.
See Grounding Instructions
under Installation.
Make certain that the electrical
circuit to which the compressor
is connected provides proper
electrical grounding, correct
voltage and adequate
fuse protection.
WARNING: RISK FROM FLYING OBJECTS
What can happen How to prevent it
The compressed air stream can
cause soft tissue damage to
exposed skin and can propel
dirt, chips, loose particles, and
small objects at high speed,
resulting in property damage or
personal injury.
Always wear certied safety
equipment: ANSI Z87.1 eye
protection (CAN/CSA Z94.3)
with side shields when using
the compressor.
Never point any nozzle or sprayer
toward any part of the body or at
other people or animals.
Always turn the compressor off and
bleed pressure from the air hose
and air tank before attempting
maintenance, attaching tools
or accessories.
WARNING: RISK OF HOT SURFACES
What can happen How to prevent it
Touching exposed metal such as
the compressor head, engine head,
engine exhaust or outlet tubes, can
result in serious burns.
Never touch any exposed metal
parts on compressor during or
immediately after operation.
Compressor will remain hot for
several minutes after operation.
Do not reach around protective
shrouds or attempt maintenance
until unit has been allowed to cool.
WARNING: RISK OF INJURY FROM LIFTING
What can happen How to prevent it
Serious injury can result from
attempting to lift too heavy
an object.
The compressor is too heavy
to be lifted by one person.
Obtain assistance from others
before lifting.
WARNING: RISK FROM MOVING PARTS
What can happen How to prevent it
Moving parts such as the pulley,
flywheel, and belt can cause
serious injury if they come into
contact with you or your clothing.
Never operate the compressor
with guards or covers which are
damaged or removed
Keep your hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long hair
can be caught in moving parts.
Air vents may cover moving parts
and should be avoided as well.
WARNING: RISK OF BURSTING (Cont.)
3
ENGLISH
Air Compressor
CMXECXM601
SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE
REFERENCE
DANGER: RISK OF EXPLOSION OR FIRE
What can happen How to prevent it
It is normal for electrical contacts
within the motor and pressure
switch to spark.
Always operate the compressor
in a well ventilated area free of
combustible materials, gasoline, or
solvent vapors.
If electrical sparks from compressor
come into contact with flammable
vapors, they may ignite, causing
fire or explosion.
If spraying flammable materials,
locate compressor at least 20 feet
(6.1 m) away from spray area.
An additional length of hose may
be required.
Store flammable materials
in a secure location away
from compressor.
Restricting any of the compressor
ventilation openings will cause
serious overheating and could
cause a fire.
Never place objects against or on
top of compressor pump.
Operate compressor in an open
area at least 12" (30.5 cm) away
from any wall or obstruct
ion that
would restrict the flow of fresh air
to the ventilation openings.
Operate compressor in a clean,
dry well ventilated area. Do not
operate unit indoors or in any
confined area.
Unattended operation of this
product could result in personal
injury or property damage.
To reduce the risk of fire, do
not allow the compressor to
operate unattended.
Always remain in attendance with
the product when it is operating.
Always turn off and unplug unit
when not in use.
CAUTION: RISK FROM NOISE
What can happen How to prevent it
Under some conditions and
duration of use, noise from
this product may contribute to
hearing loss.
Always wear certified safety
equipment: ANSI S12.6 (S3.19)
hearing protection.
DANGER: RISK TO BREATHING
(Asphyxiation)
What can happen How to prevent it
The compressed air directly from
your compressor is not safe for
breathing. The air stream may
contain carbon monoxide, toxic
vapors, or solid particles from
the air tank. Breathing these
contaminants can cause serious
injury or death.
Air obtained directly from the
compressor should never be
used to supply air for human
consumption. In order to use air
produced by this compressor for
breathing, suitablelters and
in-line safety equipment must be
properly installed. In-line filters
and safety equipment used in
conjunction with the compressor
must be capable of treating air
to all applicable local and federal
codes prior to human consumption.
Exposure to chemicals in dust
created by power sanding,
sawing, grinding, drilling, and
other constructio
n activities may
be harmful.
Work in an area with good
ventilation. Read and follow the
safety instructions provided on the
label or safety data sheets for the
materials you are spraying. Always
use certified safety equipment:
OSHA/MSHA/NIOSH respiratory
protection designed for use with
your specific application.
Sprayed materials such as paint,
paint solvents, paint remover,
insecticides, weed killers,
may contain harmful vapors
and poisons.
WARNING: RISK OF BURSTING
Air Tank:
On February 26, 2002, the U.S. Consumer
Product Safety Commission published Release # 02-108
concerning air compressor tank safety:
Air compressor receiver tanks do not have an infinite
life. Tank life is dependent upon several factors, some of
which include operating conditions, ambient conditions,
proper installations, field modifications, and the level
of maintenance. The exact effect of these factors on air
If proper maintenance procedures are not followed,
internal corrosion to the inner wall of the air receiver tank
can cause the air tank to unexpectedly rupture allowing
pressurized air to suddenly and forcefully escape, posing
Your compressor air tank must be removed from service
The following conditions could lead to a weakening of the
air tank, and result in a violent air tank explosion:
WARNING:
CONTAINS LEAD. May be harmful if eaten or
chewed. May generate dust containing lead.
Wash hands after use. Keep out of reach of children
WARNING:
This product can expose you to chemicals
including lead, which is known to the State of
California to cause cancer and birth defects
or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
ENGLISH
What can happen How to prevent it
Failure to properly drain condensed
water from air tank causes rust
and thinning of the steel air tank.
Drain air tank daily or after each
use. If air tank develops a leak,
replace it immediately with
a new air tank or replace the
entire compressor.
Modifications or attempted repairs
to the air tank.
Never drill into, weld, or make
any modifications to the air tank
or its attachments. Never attempt
to repair a damaged or leaking air
tank. Replace with a new air tank.
Unauthorized modifications to
the safety valve or any other
components which control air
tank pressure.
The air tank is designed to
withstand specific operating
pressures. Never make adjustments
or parts substitutions to alter the
factory set operating pressures.
Attachments & accessories:
Exceeding t
he pressure rating of
air tools, spray guns, air operated
accessories, tires, and other
inflatables can cause them to
explode or fly apart, and could
result in serious injury.
Follow the equipment
manufacturers recommendation
and never exceed the maximum
allowable pressure rating of
attachments. Never use compressor
to inflate small low pressure
objects such as children’s toys,
footballs, basketballs, etc.
Tires:
Over inflation of tires could
result in serious injury and
property damage.
Use a tire pressure gauge to check
the tires pressure before each
use and while inflating tires; see
the tire sidewall for the correct
tire pressure.
NOTE: Air tanks, compressors and
similar equipment used to inflate
tires can ll small tires similar to
these very rapidly. Adjust pressure
regulator on air
supply to no more
than the rating of the tire pressure.
Add air in small increments and
frequently use the tire gauge to
prevent over inflation.
WARNING: RISK OF ELECTRICAL SHOCK
What can happen How to prevent it
Your air compressor is powered
by electricity. Like any other
electrically powered device, If it
is not used properly it may cause
electric shock.
Never operate the compressor
outdoors when it is raining or in
wet conditions.
Never operate compressor with
protective covers removed
or damaged.
Repairs attempted by unqualified
personnel can result in serious
injury or death by electrocution.
Any repairs required on this
product should be performed
by authorized service
center personnel.
Electrical Grounding: Failure
to provide adequate grounding to
this product could result in serious
injury or death from electrocution.
See Grounding Instructions
under Installation.
Make certain that the electrical
circuit to which the compressor
is connected provides proper
electrical grounding, correct
voltage and adequate
fuse protection.
WARNING: RISK FROM FLYING OBJECTS
What can happen How to prevent it
The compressed air stream can
cause soft tissue damage to
exposed skin and can propel
dirt, chips, loose particles, and
small objects at high speed,
resulting in property damage or
personal injury.
Always wear certied safety
equipment: ANSI Z87.1 eye
protection (CAN/CSA Z94.3)
with side shields when using
the compressor.
Never point any nozzle or sprayer
toward any part of the body or at
other people or animals.
Always turn the compressor off and
bleed pressure from the air hose
and air tank before attempting
maintenance, attaching tools
or accessories.
WARNING: RISK OF HOT SURFACES
What can happen How to prevent it
Touching exposed metal such as
the compressor head, engine head,
engine exhaust or outlet tubes, can
result in serious burns.
Never touch any exposed metal
parts on compressor during or
immediately after operation.
Compressor will remain hot for
several minutes after operation.
Do not reach around protective
shrouds or attempt maintenance
until unit has been allowed to cool.
WARNING: RISK OF INJURY FROM LIFTING
What can happen How to prevent it
Serious injury can result from
attempting to lift too heavy
an object.
The compressor is too heavy
to be lifted by one person.
Obtain assistance from others
before lifting.
WARNING: RISK FROM MOVING PARTS
What can happen How to prevent it
Moving parts such as the pulley,
flywheel, and belt can cause
serious injury if they come into
contact with you or your clothing.
Never operate the compressor
with guards or covers which are
damaged or removed
Keep your hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long hair
can be caught in moving parts.
Air vents may cover moving parts
and should be avoided as well.
WARNING: RISK OF BURSTING (Cont.)
4
ENGLISH
Specifications
Model CMXECXM601
Bore 2.68" (68.014 mm)
Stroke 1.50" (35 mm)
Voltage/Hz-Single Phase 240/60
Minimum Branch Circuit Requirement 20 amps
Fuse Type Time Delay
Air Tank Capacity 60 Gallons (227.1 liters)
Approximate Cut-in Pressure 145 psi
Approximate Cut-out Pressure 175 psi
CFM:
SCFM: Standard cubic feet per minute; a unit of measure of
air delivery.
PSIG: Pounds per square inch gauge; a unit of measure
of pressure.
PSI: Pounds per square inch; a unit of pressure.
Code Certification: Products that bear one or more of the
following marks: UL®, CUL, CULUS, ETL®, CETL, CETLUS, have
been evaluated by OSHA certified independent safety
Cut-In Pressure: While the motor is off, air tank pressure
drops as you continue to use your accessory. When the tank
pressure drops to a certain lower level the motor will restart
automatically. The low pressure at which the motor
Cut-Out Pressure: When an air compressor is turned on
and begins to run, air pressure in the air tank begins to build.
It builds to a certain high pressure before the motor
automatically shuts off, protecting your air tank from
pressure higher than its capacity. The high pressure at which
Branch Circuit: Circuit carrying electricity from electrical
Duty Cycle: For proper operation of your air compressor, it
is recommended that a 50% duty cycle be maintained; that
is, the air compressor should not run more than 30 minutes in
any 60 minute period.
SCFM @ 40 psig 13.4 *
SCFM @ 90 psig 11.5 *
Tank Fill Time 7 minutes
Duty Cycle 50%, ex. 30 minutes each hour
Weight Approximately 200 lbs (91 kg)
*Tested per ISO 1217
Refer to Glossary for abbreviations.
Attempting to operate compressor
with damaged or missing parts or
attempting to repair compressor
with protective shrouds removed
can expose you to moving parts
and can result in serious injury.
Any repairs required on this
product should be performed
by authorized service
center personnel.
WARNING: RISK OF UNSAFE OPERATION
What can happen How to prevent it
Unsafe op er a tion of your air
compressor could lead to se ri ous
in ju ry or death to you or others.
Review and understand all
instructions and warnings in
this manual.
Be come fa mil iar with the op eration
and con trols of the air compressor.
Keep operating area clear of all
persons, pets, and obstacles.
Keep chil dren away from the air
compressor at all times.
Do not operate the product when
fatigued or under the influence
of alcohol or drugs. Stay alert at
all times.
Never defeat the safety fea tures of
this prod uct.
Equip area of operation with a
fire extinguisher.
Do not op er ate machine
with missing, broken, or
un authorized parts.
Never stand on
the compressor.
WARNING: RISK FROM MOVING PARTS (Cont.)
Well-ventilated: A means of providing fresh air in exchange
for dangerous exhaust or vapors.
Dedicated circuit: An electrical circuit reserved for the
exclusive use of the air compressor.
ASME: American Society of Mechanical Engineers. Indicates
that the components are manufactured, tested and
inspected to the specifications set by ASME.
CSA: Canadian Standards Association
Indicates that the products that have this marking
have been manufactured, tested and inspected to
standards that are set by CSA.
Canadian Standards Association (USA): Indicates that the
products that have this marking have been
manufactured, tested and inspected to standards
that are set by CSA. These products also conform to
U.L. standard 1450.
California Code: Unit may comply with California Code 462
(l) (2)/(M) (2). Specification/model label is on the side
of the air tank on units that comply with California Code.
GLOSSARY
UNPACKING
INSTALLATION
How To Set Up Your Unit
Location of the Air Compressor
Locate the air compressor in a clean, dry and well
ventilated area.
The air compressor should be located at least 12"
(30.5 cm) away from the wall or other obstructions that
will interfere with the flow of air.
The air compressor pump and shroud are designed to
allow for proper cooling. The ventilation openings on
the compressor are necessary to maintain proper
operating temperature. Do not place rags or other
Remove unit from package and discard all
packaging.
Grounding Instructions
1. Place the air compressor on a level, solid
concrete surface. Make sure the concrete is in
good condition with no cracks or damage.
2. Mark the surface using the holes in the air
compressor feet as a template.
3. Drill holes in the surface for the concrete
anchors. Install concrete anchors.
4. Line-up holes in surface with holes in air
compressor feet.
5. Place the vibration pads between the floor and
air compressor feet, see figure. If needed use
shims to level the unit.
6. Place the 3/8" lag screws through the air
compressor feet, vibration pads and into the
anchors.
7. Torque 3/8" lag screws to 7-10 ft.-lbs
(9.5-13.5 Nm).
ENGLISH
ASSEMBLY AND ADJUSTMENTS
Anchoring of the Air Compressor
WARNING: Risk of bursting. Excessive vibration
can weaken the air tank and cause an explosion.
The compressor must be properly mounted.
The air compressor MUST be properly mounted. The air
compressor MUST be bolted to a level, solid concrete
surface. Use 3/8” lag screws, vibration pads and concrete
anchors
NOISE CONSIDERATIONS
Consult local officials for information regarding
acceptable noise levels in your area. To reduce excessive
noise, use vibration mounts or silencers, or relocate the
unit.
WARNING: Risk of electrical shock. In the event
of a short circuit, grounding reduces the risk of
shock by providing an escape wire for the
electric current. This air compressor must be
properly grounded.
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
WARNING: Risk of unsafe operation. Unit cycles
automatically when power is on. When performing
maintenance, you may be exposed to voltage
sources, compressed air, or moving parts. Personal
injuries can occur. Before performing any
maintenance or repair, disconnect power source
from the compressor and bleed off all air pressure.
DANGER: Risk of electrical shock. IMPROPER
GROUNDING CAN RESULT IN ELECTRICAL
SHOCK.
This product must be connected to a grounded, metallic,
permanent wiring system, or an equipment-grounding
terminal or lead on the product.
5
UNPACKING
INSTALLATION
How To Set Up Your Unit
Location of the Air Compressor
Locate the air compressor in a clean, dry and well
ventilated area.
The air compressor should be located at least 12"
(30.5 cm) away from the wall or other obstructions that
will interfere with the flow of air.
The air compressor pump and shroud are designed to
allow for proper cooling. The ventilation openings on
the compressor are necessary to maintain proper
operating temperature. Do not place rags or other
Remove unit from package and discard all
packaging.
Grounding Instructions
1. Place the air compressor on a level, solid
concrete surface. Make sure the concrete is in
good condition with no cracks or damage.
2. Mark the surface using the holes in the air
compressor feet as a template.
3. Drill holes in the surface for the concrete
anchors. Install concrete anchors.
4. Line-up holes in surface with holes in air
compressor feet.
5. Place the vibration pads between the floor and
air compressor feet, see figure. If needed use
shims to level the unit.
6. Place the 3/8" lag screws through the air
compressor feet, vibration pads and into the
anchors.
7. Torque 3/8" lag screws to 7-10 ft.-lbs
(9.5-13.5 Nm).
ENGLISH
ASSEMBLY AND ADJUSTMENTS
Anchoring of the Air Compressor
WARNING: Risk of bursting. Excessive vibration
can weaken the air tank and cause an explosion.
The compressor must be properly mounted.
The air compressor MUST be properly mounted. The air
compressor MUST be bolted to a level, solid concrete
surface. Use 3/8” lag screws, vibration pads and concrete
anchors
NOISE CONSIDERATIONS
Consult local officials for information regarding
acceptable noise levels in your area. To reduce excessive
noise, use vibration mounts or silencers, or relocate the
unit.
WARNING: Risk of electrical shock. In the event
of a short circuit, grounding reduces the risk of
shock by providing an escape wire for the
electric current. This air compressor must be
properly grounded.
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
WARNING: Risk of unsafe operation. Unit cycles
automatically when power is on. When performing
maintenance, you may be exposed to voltage
sources, compressed air, or moving parts. Personal
injuries can occur. Before performing any
maintenance or repair, disconnect power source
from the compressor and bleed off all air pressure.
DANGER: Risk of electrical shock. IMPROPER
GROUNDING CAN RESULT IN ELECTRICAL
SHOCK.
This product must be connected to a grounded, metallic,
permanent wiring system, or an equipment-grounding
terminal or lead on the product.
6
ENGLISH
Voltage and Circuit Protection
Refer to the Voltage and Minimum Branch Circuit
Requirements under Specifications.
• Voltage supply to circuit must comply with
the National Electrical Code.
• Circuit is not used to supply any other electrical needs.
NOTE: If compressor is connected to a circuit protected by
fuses, use only time delay fuses. Time delay fuses should be
marked “D” in Canada and “T” in the US.
Main Power Disconnect Switch
Install a main power disconnect switch in the line from the panel
to the compressor. The main power disconnect switch must be
located near the compressor, for ease of use and safety. When
turned OFF, the main power disconnect switch shuts off all power
to the compressor. When it is turned ON, the compressor will start
and stop automatically, controlled by the pressure switch.
Electrical Wiring
WARNING: Improper electrical installation of this
product may void its warranty and your fire insurance.
Have circuit wiring performed by qualified personnel
such as a licensed electrician who is familiar with the
current national electrical code and any prevailing local
electrical codes.
WARNING: Risk of electrical shock. Improper electrical
grounding can result in electrical shock.
The wiring should be done by a qualified electrician.
A qualified electrician needs to know the following before wiring:
The amperage rating of the electrical box is adequate.
Refer to the Specifications, in the instruction manual, for this
information.
• If the supply line has the same electrical characteristics
(voltage, cycle, phase) as the motor. Refer to the motor
nameplate, on side of motor, for this information.
NOTE: The wiring used must be rated for the motor nameplate
voltage, plus or minus 10%. Refer to local codes for recommend-
ed wire sizes, correct wire size, and maximum wire run.
Undersized wire causes high amp draw and overheating to the
motor.
NOTE: A circuit breaker is recommended. If the air compressor is
connected to a circuit protected by a fuse, use only time delay
fuses.
WARNING: Risk of electrical shock. Electrical wiring
must be located away from hot surfaces such as
manifold assembly, compressor outlet tubes, heads,
or cylinders.
Air Distribution System
WARNING: Risk of bursting. Plastic or PVC pipe is not
designed for use with compressed air. Regardless
of its indicated pressure rating, plastic pipe can
burst from air pressure. Use only metal pipe for air
distribution lines.
INSTALLING AND DISCONNECTING HOSES
WARNING: Risk of unsafe operation. Firmly grasp
hose in hand when installing or disconnecting to
prevent hose whip. Ensure regulated pressure gauge
reads 0 PSI.
The next figure represents a typical air distribution system.
The following are tips to remember when setting up the air
compressor’s air distribution system.
NOTE: Compressed air from oil lubed air compressors will
contain water condensation and oil mist. Several drains, traps
and filters will be needed to supply air without water
(including aerosols) or oil to spray equipment, air tools and
accessories requiring filtered air. Always read the instructions
for the air tools and accessories being used.
• Use pipe that is the same size as the air tank outlet. Piping
that is too small will restrict the flow of air.
• If piping is over 100' (30.5 m) long, use the next larger size.
• Bury underground lines below the frost line and avoid
pockets where condensation can gather and freeze. Apply
pressure before underground lines are covered to make
sure all pipe joints are free of leaks.
• A flexible coupling is recommended to be installed
between the globe valve/air discharge outlet and main air
distribution line to allow for vibration.
• A separate regulator is recommended to control the air
pressure. Air pressure from the tank is usually too high for
individual air driven tools.
• DO NOT install lubricators between the tank and any spray
equipment, air tool or accessory requiring oil-free filtered
air.
• Drain all traps, filters and dirt legs daily.
SEE NEXT PAGE FOR TYPICAL COMPRESSED AIR DISTRIBUTION
SYSTEM
7
ENGLISH
Voltage and Circuit Protection
Refer to the Voltage and Minimum Branch Circuit
Requirements under Specifications.
• Voltage supply to circuit must comply with
the National Electrical Code.
• Circuit is not used to supply any other electrical needs.
NOTE: If compressor is connected to a circuit protected by
fuses, use only time delay fuses. Time delay fuses should be
marked “D” in Canada and “T” in the US.
Main Power Disconnect Switch
Install a main power disconnect switch in the line from the panel
to the compressor. The main power disconnect switch must be
located near the compressor, for ease of use and safety. When
turned OFF, the main power disconnect switch shuts off all power
to the compressor. When it is turned ON, the compressor will start
and stop automatically, controlled by the pressure switch.
Electrical Wiring
WARNING: Improper electrical installation of this
product may void its warranty and your fire insurance.
Have circuit wiring performed by qualified personnel
such as a licensed electrician who is familiar with the
current national electrical code and any prevailing local
electrical codes.
WARNING: Risk of electrical shock. Improper electrical
grounding can result in electrical shock.
The wiring should be done by a qualified electrician.
A qualified electrician needs to know the following before wiring:
The amperage rating of the electrical box is adequate.
Refer to the Specifications, in the instruction manual, for this
information.
• If the supply line has the same electrical characteristics
(voltage, cycle, phase) as the motor. Refer to the motor
nameplate, on side of motor, for this information.
NOTE: The wiring used must be rated for the motor nameplate
voltage, plus or minus 10%. Refer to local codes for recommend-
ed wire sizes, correct wire size, and maximum wire run.
Undersized wire causes high amp draw and overheating to the
motor.
NOTE: A circuit breaker is recommended. If the air compressor is
connected to a circuit protected by a fuse, use only time delay
fuses.
WARNING: Risk of electrical shock. Electrical wiring
must be located away from hot surfaces such as
manifold assembly, compressor outlet tubes, heads,
or cylinders.
Air Distribution System
WARNING: Risk of bursting. Plastic or PVC pipe is not
designed for use with compressed air. Regardless
of its indicated pressure rating, plastic pipe can
burst from air pressure. Use only metal pipe for air
distribution lines.
INSTALLING AND DISCONNECTING HOSES
WARNING: Risk of unsafe operation. Firmly grasp
hose in hand when installing or disconnecting to
prevent hose whip. Ensure regulated pressure gauge
reads 0 PSI.
The next figure represents a typical air distribution system.
The following are tips to remember when setting up the air
compressor’s air distribution system.
NOTE: Compressed air from oil lubed air compressors will
contain water condensation and oil mist. Several drains, traps
and filters will be needed to supply air without water
(including aerosols) or oil to spray equipment, air tools and
accessories requiring filtered air. Always read the instructions
for the air tools and accessories being used.
• Use pipe that is the same size as the air tank outlet. Piping
that is too small will restrict the flow of air.
• If piping is over 100' (30.5 m) long, use the next larger size.
• Bury underground lines below the frost line and avoid
pockets where condensation can gather and freeze. Apply
pressure before underground lines are covered to make
sure all pipe joints are free of leaks.
• A flexible coupling is recommended to be installed
between the globe valve/air discharge outlet and main air
distribution line to allow for vibration.
• A separate regulator is recommended to control the air
pressure. Air pressure from the tank is usually too high for
individual air driven tools.
• DO NOT install lubricators between the tank and any spray
equipment, air tool or accessory requiring oil-free filtered
air.
• Drain all traps, filters and dirt legs daily.
SEE NEXT PAGE FOR TYPICAL COMPRESSED AIR DISTRIBUTION
SYSTEM
TYPICAL COMPRESSED AIR DISTRIBUTION SYSTEM
ENGLISH
S
Part Description
A
Drain Legs
B
Drain Valves
C
Lubricator
D
Air Tool
E
Regulator
F
Filter / Moisture Trap
G
Air Usage Lines
H
Dirt Legs
I
Air Discharge Valve
J
Feeder Lines Slope with Air Flow
K
Main Distribution Air Lines - Slope pipe in direction
of air flow. Water condensate flows along bottom
of pipe to drain legs, preventing it from entering
feeder lines.
L
5 Micron Filter
M
.01 Micron Filter
N
Spray Gun
O
Ball Fitter
P
Flexible Coupling
Q
For Best Performance - The distance between the
compressor and the moisture trap should be as
long as possi
ble.
R
Air Flow
S
Air Outlet
OPERATION
WARNING: To reduce the risk of serious personal injury, turn
unit off and disconnect it from power source before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
WARNING: Risk of unsafe operation. Unit cycles
automatically when power is on. When performing
maintenance, you may be exposed to voltage sources,
compressed air, or moving parts. Personal injuries can occur.
Before performing any maintenance or repair, disconnect
power source from the compressor and bleed off all air
pressure.
8
ENGLISH
Know The Air Compressor
READ THIS INSTRUCTION MANUAL AND SAFETY RULES
BEFORE OPERATING THE UNIT. Compare the illustrations
with the unit to familiarize yourself with the location of
various controls and adjustments. Save this manual for
future reference.
Description of Operation (Fig. A)
Become familiar with these controls before operating
the unit.
AUTO (-) / OFF (O) SWITCH
Place this switch (1) in the "AUTO (-)" position to provide
automatic power to the pressure switch and "OFF (O)" to
remove power at the end of each use.
PRESSURE SWITCH (NOT SHOWN)
The pressure switch (2) automatically starts the motor when
the air tank pressure drops below the factory set "cut-in”
pressure. It stops the motor when the air tank pressure
reaches the factory set "cut-out" pressure.
SAFETY VALVE
If the pressure switch does not shut off the air compressor at
its “cut-out” pressure setting, the safety valve (3) will protect
against high pressure by “popping out” at its factory set
pressure (slightly higher than the pressure switch “cut-out”
setting).
TANK PRESSURE GAUGE (SUPPLIED)
The tank pressure gauge (4) indicates the reserve air
pressure in the tank.
AIR INTAKE FILTER
The filter (6) is designed to clean air entering the pump. To
ensure the pump continually receives a clean, cool, and dry
air supply, the filter must always be clean and the filter
intake must be free from obstructions.
REGULATOR (SOLD SEPARATELY, NOT SHOWN)
Controls the air pressure shown on the outlet pressure
gauge. Turn regulator knob clockwise to increase pressure
and counterclockwise to decrease pressure.
WARNING: Risk of Bursting. Too much air pressure
causes a hazardous risk of bursting. Check the
manufacturer’s maximum pressure rating for air
tools and accessories. The tank outlet pressure
must never exceed the maximum pressure rating
of the tools or accessories.
AIR COMPRESSOR PUMP
Compresses air into the air tank. Working air is not available
until the compressor has raised the air tank pressure above
that required at the air outlet.
DRAIN VALVE
The drain valve (8) is located at the base of the air tank and is
used to drain condensation at the end of each use.
CHECK VALVE
When the air compressor is operating, the check valve (5) is
"open", allowing compressed air to enter the air tank. When
the air compressor reaches “cut-out” pressure, the check
valve "closes", allowing air pressure to remain inside the air
tank.
MOTOR OVERLOAD PROTECTOR
The motor has a thermal overload protector. If the motor
overheats for any reason, the overload protector will shut off the
motor. The motor must be allowed to cool down before
restarting.
To restart:
1. Move the Auto/Off switch to "OFF (O)" and unplug unit.
2. Allow the motor to cool.
3. Depress the red reset button (10) on the motor.
4. Plug the power cord into the correct branch circuit
receptacle.
5. Move the Auto/Off switch to "AUTO (-)".
How to Use The Unit
How to Stop
1. Move the Auto/Off switch to "OFF (O)".
2. Unplug unit when not in use.
Before Starting
WARNING: Do not operate this unit until you read this
instruction manual for safety, operation and
maintenance instructions.
Break-in Procedure
NOTICE: Risk of property damage. Serious damage may result if
the following break-in instructions are not closely followed.
This procedure is required before the air compressor is put into
service and when the check valve or a complete compressor
pump has been replaced.
1. Make sure the Auto/Off switch is in the "OFF (O)"
position.
2. Check oil level in pump. See Oil paragraph in the
Maintenance section for instructions.
3. Recheck all wiring. Make sure wires are secure at all
terminals connections. Make sure all contacts move
freely and are not obstructed.
4. Open the drain valve fully to permit air to
escape and prevent air pressure build up in the air tank
during the break-in period.
5. Move the Auto/Off switch to "AUTO (-)" position. The
compressor will start.
6. Run the compressor for 30 minutes. Make sure the
drain valve and all air lines are open so there is only a
minimal air pressure build-up in tank.
NOTE: After about 30 minutes, If the unit does not
operate properly, SHUT DOWN IMMEDIATELY, and
contact Product Service.
7. Check for excessive vibration. Re-adjust or shim air
compressor feet, if necessary.
8. After 30 minutes, turn the Auto/Off switch to the "OFF (O)"
position.
9. Close the drain valve.
10. Move the Auto/Off switch to the "AUTO (-)" position.
The air receiver will fill to “cut-out” pressure and the
motor will stop.
11. Check all air line fittings and connections/piping for air
leaks by applying a soap solution. Correct if necessary.
NOTE: Minor leaks can cause the air compressor to
overwork, resulting in premature breakdown or
inadequate performance.
12. The compressor is now ready for use.
ENGLISH
Before Each Start-Up
1. Every day check the sight glass (15) to ensure that the
level of oil in the pump is at the required level.
2. Move Auto/Off switch to "OFF (O)".
3. Close the drain valve.
4. Visually inspect air lines and fittings for leaks.
5. Check safety valve. See To Check Safety Valve
under Maintenance.
6. Attach hose and accessories.
WARNING: Risk of unsafe operation. Firmly grasp
air hose in hand when installing or disconnecting
to prevent hose whip.
Warning: Risk of unsafe operation. Do not use
damaged or worn accessories.
NOTE: The hose or accessory will require a quick connect
plug if the air outlet is equipped with a quick connect
socket.
WARNING: Risk of bursting. Too much air pressure
causes a hazardous risk of bursting. Check the
manufacturer’s maximum pressure rating for air
tools and accessories. The regulator outlet
pressure must never exceed the maximum
pressure rating.
NOTICE: Risk of property damage. Compressed air from the
unit may contain water condensation and oil mist. Do not
spray unfiltered air at an item that could be damaged by
moisture. Some air tools and accessories may require filtered
air. Read the instructions for the air tools and accessories.
How to Start
1. Move the Auto/Off switch to "AUTO (-)" and allow
tank pressure to build. Motor will stop when tank
pressure reaches “cut-out” pressure.
2. When the tank pressure reaches "cut-out" pressure
open the air discharge valve.
IMPORTANT: When using a regulator and other accessories
refer to the manufacturer's instructions.
WARNING: Risk of bursting. If any unusual noise or
vibration is noticed, stop the compressor
immediately and have it checked by a trained
service technician.
3. The compressor is ready for use.
How to Shut Down
1. Move Auto/Off switch to the "OFF (O)" position.
NOTE: If finished using compressor, follow
steps 2 - 5.
2. Drain the air tank, see Draining Air Tank under
Maintenance. Ensure air tank pressure gauge reads
0 PSI (0 kPa).
3. Remove hose and accessory.
4. Allow the compressor to cool down.
5. Wipe air compressor clean and store in a safe,
non-freezing area.
WARNING: Risk of unsafe operation. Firmly grasp
air hose in hand when installing or disconnecting
to prevent hose whip.
WARNING: Risk of bursting. Drain air tank daily.
Water will condense in air tank. If not drained,
water will corrode and weaken the air tank
causing a risk of air tank rupture.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
WARNING: Risk of unsafe operation. Unit cycles
automatically when power is on. When performing
maintenance, you may be exposed to voltage
sources, compressed air, or moving parts. Personal
injuries can occur. Before performing any
maintenance or repair, disconnect power source
from the compressor and bleed off all air pressure.
To ensure efficient operation and longer life of the air
compressor outfit, a routine maintenance schedule should be
prepared and followed. The following routine maintenance
schedule is geared to an outfit in a normal working
environment operating on a daily basis. If necessary, the
schedule should be modified to suit the conditions under
which the compressor is used. The modifications will depend
upon the hours of operation and the working environment.
Compressor outfits in an extremely dirty and/or hostile
environment will require a greater frequency of all
maintenance checks.
X
X
X
X
X
X
X*
X
X**
X
X+
X
Customer Responsibilities
Check safety valve
Drain Tank
Check Pump Oil Level
Inspect Air Filter
Change Oil Pump
Oil Leak Inspection
Inspect Drive Belt
Check Drive Belt
Tension
Check Pulley/
Flywheel Alignment
Check for Unusual
Noise/Vibration
Check for Air Leaks
Clean Compressor
Exterior
***SEE TANK WARNING LABEL FOR DATE TO REMOVE TANK
FROM SERVICE***For more information, call our Customer
Care Center at 1-888-331-4569
*To check for air leaks apply a solution of soapy water around
joints. While compressor is pumping to pressure and after
pressure cuts out, look for air bubbles to form.
**the pump oil must be changed after the first 20 hours of
operation. Thereafter, when using full synthetic non-detergent
air compressor oil, change oil every 100 hours of operation or
once a year, whichever comes first.
+Perform more frequent in dusty or humid conditions.
NOTE: See Operation section for the location of controls.
Daily Weekly 1 Year or
Every
100 Hours
Monthly
9
ENGLISH
Before Each Start-Up
1. Every day check the sight glass (15) to ensure that the
level of oil in the pump is at the required level.
2. Move Auto/Off switch to "OFF (O)".
3. Close the drain valve.
4. Visually inspect air lines and fittings for leaks.
5. Check safety valve. See To Check Safety Valve
under Maintenance.
6. Attach hose and accessories.
WARNING: Risk of unsafe operation. Firmly grasp
air hose in hand when installing or disconnecting
to prevent hose whip.
Warning: Risk of unsafe operation. Do not use
damaged or worn accessories.
NOTE: The hose or accessory will require a quick connect
plug if the air outlet is equipped with a quick connect
socket.
WARNING: Risk of bursting. Too much air pressure
causes a hazardous risk of bursting. Check the
manufacturer’s maximum pressure rating for air
tools and accessories. The regulator outlet
pressure must never exceed the maximum
pressure rating.
NOTICE: Risk of property damage. Compressed air from the
unit may contain water condensation and oil mist. Do not
spray unfiltered air at an item that could be damaged by
moisture. Some air tools and accessories may require filtered
air. Read the instructions for the air tools and accessories.
How to Start
1. Move the Auto/Off switch to "AUTO (-)" and allow
tank pressure to build. Motor will stop when tank
pressure reaches “cut-out” pressure.
2. When the tank pressure reaches "cut-out" pressure
open the air discharge valve.
IMPORTANT: When using a regulator and other accessories
refer to the manufacturer's instructions.
WARNING: Risk of bursting. If any unusual noise or
vibration is noticed, stop the compressor
immediately and have it checked by a trained
service technician.
3. The compressor is ready for use.
How to Shut Down
1. Move Auto/Off switch to the "OFF (O)" position.
NOTE: If finished using compressor, follow
steps 2 - 5.
2. Drain the air tank, see Draining Air Tank under
Maintenance. Ensure air tank pressure gauge reads
0 PSI (0 kPa).
3. Remove hose and accessory.
4. Allow the compressor to cool down.
5. Wipe air compressor clean and store in a safe,
non-freezing area.
WARNING: Risk of unsafe operation. Firmly grasp
air hose in hand when installing or disconnecting
to prevent hose whip.
WARNING: Risk of bursting. Drain air tank daily.
Water will condense in air tank. If not drained,
water will corrode and weaken the air tank
causing a risk of air tank rupture.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
WARNING: Risk of unsafe operation. Unit cycles
automatically when power is on. When performing
maintenance, you may be exposed to voltage
sources, compressed air, or moving parts. Personal
injuries can occur. Before performing any
maintenance or repair, disconnect power source
from the compressor and bleed off all air pressure.
To ensure efficient operation and longer life of the air
compressor outfit, a routine maintenance schedule should be
prepared and followed. The following routine maintenance
schedule is geared to an outfit in a normal working
environment operating on a daily basis. If necessary, the
schedule should be modified to suit the conditions under
which the compressor is used. The modifications will depend
upon the hours of operation and the working environment.
Compressor outfits in an extremely dirty and/or hostile
environment will require a greater frequency of all
maintenance checks.
X
X
X
X
X
X
X*
X
X**
X
X+
X
Customer Responsibilities
Check safety valve
Drain Tank
Check Pump Oil Level
Inspect Air Filter
Change Oil Pump
Oil Leak Inspection
Inspect Drive Belt
Check Drive Belt
Tension
Check Pulley/
Flywheel Alignment
Check for Unusual
Noise/Vibration
Check for Air Leaks
Clean Compressor
Exterior
***SEE TANK WARNING LABEL FOR DATE TO REMOVE TANK
FROM SERVICE***For more information, call our Customer
Care Center at 1-888-331-4569
*To check for air leaks apply a solution of soapy water around
joints. While compressor is pumping to pressure and after
pressure cuts out, look for air bubbles to form.
**the pump oil must be changed after the first 20 hours of
operation. Thereafter, when using full synthetic non-detergent
air compressor oil, change oil every 100 hours of operation or
once a year, whichever comes first.
+Perform more frequent in dusty or humid conditions.
NOTE: See Operation section for the location of controls.
Daily Weekly 1 Year or
Every
100 Hours
Monthly
10
ENGLISH
To Check Safety Valve
WARNING: Risk of bursting. If the safety valve does not
work properly, over-pressurization may occur,
causing air tank rupture or an explosion.
WARNING: Risk from flying objects. Always wear
certified safety equipment: ANSI Z87.1 eye protection
(CAN/CSA Z94.3) with side shields.
Before starting compressor, pull the ring on the safety valve to
make sure that the safety valve operates freely. If the valve is
stuck or does not operate smoothly, it must be replaced with
the same type of valve.
To Drain Tank
WARNING: Risk of unsafe operation. Air tanks contain
high pressure air. Keep face and other body parts
away from outlet of drain. Use eye protection
[ANSIZ87.1 (CAN/CSAZ94.3)] when draining as debris
can be kicked up into face.
WARNING: Risk from noise. Always wear proper
hearing protection during use. Under some
conditions and duration of use, noise from this
product may contribute to hearing loss.
NOTE: All compressed air systems generate condensation that
accumulates in any drain point (e.g., tanks, filter, aftercoolers,
dryers). This condensate contains lubricating oil and/or
substances which may be regulated and must be disposed of in
accordance with local, state, and federal laws and regulations.
WARNING: Risk of bursting. Water will condense in the
air tank. If not drained, water will corrode and
weaken the air tank causing a risk of air tank
rupture.
NOTICE: Risk of property damage. Drain water from air tank
may contain oil and rust which can cause stains.
1. Move the Auto/Off switch to "OFF (O)".
2. Turn regulator knob counterclockwise to set the outlet
pressure to zero.
3. Pull ring on safety valve allowing air to bleed from the
tank until tank pressure is approximately 20 PSI.
Release safety valve ring.
4. Remove the air tool or accessory.
5. Place a suitable container under the drain valve
to catch discharge.
6. Drain water from air tank by opening drain valve on
bottom of tank.
7. After the water has been drained, close the
drain valve. The air compressor can now be stored.
NOTE: If drain valve is plugged, release all air pressure. The valve
can then be removed, cleaned, then reinstalled.
To Check Air Intake Filter
WARNING: Hot surfaces. Risk of burn. Tubes, pump
head, and surrounding parts are very hot, do not
touch (See Hot Surfaces identification (Fig. A)). Allow
compressor to cool prior to servicing.
A dirty air filter will not allow the compressor to operate at full
capacity. Keep the air filter clean at all times.
1. Ensure Auto/Off switch is in the "OFF (O)" position.
2. Allow unit to cool.
3. Unsnap the air filter cover to remove.
4. Check the filter element. If it is dirty, blow
compressed air through the filter element for 10-15
seconds or replace if needed. If the filter is filled with
paint, replace it.
5. Place element into housing and reattach the air
filter cover.
CAUTION: Risk of unsafe operation. Do not operate
without air filter.
Compressor Pump Oil
NOTICE: Risk of property damage. Use air compressor oil only.
Multi-weight automotive engine oils like 10W30 should not be
used in air compressors. They leave carbon deposits on critical
components, thus reducing performance and compressor life.
NOTE: Use full synthetic, non-detergent air compressor oil.
NOTE: Crankcase oil capacity is approximately 16 fluid ounces
(473ml).
To Check
WARNING: Drain tank to release air pressure before
removing the oil fill plug or oil drain plug.
1. Remove the oil fill plug (14).
2. Remove the oil drain plug (16) and drain oil into a
suitable container.
3. Replace the oil drain plug and tighten securely
4. Slowly add compressor oil until it reaches the middle
of the sight glass (15). NOTE: When filling the
crankcase, the oil flows very slowly into the pump. If the
oil is added too quickly, it will overflow and appear to
be full.
CAUTION: Overfilling with oil will cause premature
compressor failure. Do not overfill.
5. Replace oil fill plug and tighten securely.
ENGLISH
WARNING: This unit starts automatically.
ALWAYS shut off and unplug the compressor, and
bleed all pressure from the system before
servicing the compressor, and when the
compressor is not in use. Do not use the unit with
the shrouds or belt guard removed. Serious injury
could occur from contact with moving parts. Hot
surfaces. Risk of burn. Pump head, and
surrounding parts are very hot, do not touch (see
the Hot Surfaces identified in Fig. A). Allow
compressor to cool prior to servicing.
1. Move the Auto/Off switch to "OFF (O)", unplug the
unit, and relieve all air pressure from the air tank.
2. Remove the outer belt guard.
3. Mark motor position on saddle.
4. Loosen the motor mounting screws and slide the
motor toward the air compressor pump.
5. Remove the belt and replace
with a new one.
6. See the Adjusting Belt Tension before tightening
motor mounting screws.
To Adjust Belt Tension
1. Slide motor into original position, line the motor
up with the mark made earlier on saddle.
2. Tighten two outside motor mounting screws
enough to hold the motor in place for checking
pulley and flywheel alignment.
3. The belt should deflect 1/4" (6.5mm) at
midway between the pulley and the flywheel
when a 10 pound (4.5kg.) weight is applied at the
midway point.
4. When proper belt tension is achieved, tighten
motor mounting screws. Torque to 20-25 ft-lbs
(27.1-33.9 Nm)
NOTE: Once the motor pulley has been moved from its
factory set location, the grooves of the flywheel and pulley
must be aligned to within 1/16" (1.6mm) to prevent
excessive belt wear. Verify the alignment by performing the
following Motor Pulley/Flywheel - Alignment.
To Align Motor Pulley/Flywheel
NOTE: Once the motor pulley has been moved from its
factory set location, the grooves of the flywheel and pulley
must be aligned to within 1/16" (1.6 mm) to prevent
excessive belt wear.
The air compressor flywheel and motor pulley hub must be
in-line (in the same plane) within 1/16" (1.6 mm) to assure
belt retention within flywheel belt grooves. To correct
misalignment, perform the following steps:
1. Move the Auto/Off switch to "OFF (O)", unplug the
unit, and relieve all air pressure from the air tank.
2. Remove the outer belt guard.
3. Loosen the motor mounting bolts.
4. Loosen the set screws on the motor pulley.
5. Align the motor pulley with the pump flywheel.
6. Retighten the motor pulley set screws. Torque
115-125 in.-lbs (13.0 - 14.1 Nm).
7. Adjust the proper belt tension.
8. Retighten the motor mounting bolts. Torque to
20-25 ft.-lbs (27.1–33.9 Nm)
9. Reinstall the outer belt guard. All moving parts
must be guarded.
To Check Air Compressor Pump Intake
and Exhaust Valves
Once a year have a Trained Service Technician check the air
compressor pump intake and exhaust valves.
To Inspect Air Lines and Fittings for Leaks
1. Move the Auto/Off switch to "AUTO (-)" and allow
tank pressure to build. Motor will stop when tank
pressure reaches cut-out” pressure.
2. Move the Auto/Off switch to "OFF (O)" and
unplug unit.
3. Apply a soap solution to all air-line fittings and
connections/piping to look for any leaks.
4. Pull ring on safety valve allowing air to bleed from
the tank until tank pressure is approximately 20 PSI.
Release safety valve ring.
5. Drain water from air tank by opening drain valve on
bottom of tank.
6. Correct any leaks found.
IMPORTANT: Even minor leaks can cause the air
compressor to overwork, resulting in premature
breakdown or inadequate performance.
To Replace Belt
11
ENGLISH
WARNING: This unit starts automatically.
ALWAYS shut off and unplug the compressor, and
bleed all pressure from the system before
servicing the compressor, and when the
compressor is not in use. Do not use the unit with
the shrouds or belt guard removed. Serious injury
could occur from contact with moving parts. Hot
surfaces. Risk of burn. Pump head, and
surrounding parts are very hot, do not touch (see
the Hot Surfaces identified in Fig. A). Allow
compressor to cool prior to servicing.
1. Move the Auto/Off switch to "OFF (O)", unplug the
unit, and relieve all air pressure from the air tank.
2. Remove the outer belt guard.
3. Mark motor position on saddle.
4. Loosen the motor mounting screws and slide the
motor toward the air compressor pump.
5. Remove the belt and replace
with a new one.
6. See the Adjusting Belt Tension before tightening
motor mounting screws.
To Adjust Belt Tension
1. Slide motor into original position, line the motor
up with the mark made earlier on saddle.
2. Tighten two outside motor mounting screws
enough to hold the motor in place for checking
pulley and flywheel alignment.
3. The belt should deflect 1/4" (6.5mm) at
midway between the pulley and the flywheel
when a 10 pound (4.5kg.) weight is applied at the
midway point.
4. When proper belt tension is achieved, tighten
motor mounting screws. Torque to 20-25 ft-lbs
(27.1-33.9 Nm)
NOTE: Once the motor pulley has been moved from its
factory set location, the grooves of the flywheel and pulley
must be aligned to within 1/16" (1.6mm) to prevent
excessive belt wear. Verify the alignment by performing the
following Motor Pulley/Flywheel - Alignment.
To Align Motor Pulley/Flywheel
NOTE: Once the motor pulley has been moved from its
factory set location, the grooves of the flywheel and pulley
must be aligned to within 1/16" (1.6 mm) to prevent
excessive belt wear.
The air compressor flywheel and motor pulley hub must be
in-line (in the same plane) within 1/16" (1.6 mm) to assure
belt retention within flywheel belt grooves. To correct
misalignment, perform the following steps:
1. Move the Auto/Off switch to "OFF (O)", unplug the
unit, and relieve all air pressure from the air tank.
2. Remove the outer belt guard.
3. Loosen the motor mounting bolts.
4. Loosen the set screws on the motor pulley.
5. Align the motor pulley with the pump flywheel.
6. Retighten the motor pulley set screws. Torque
115-125 in.-lbs (13.0 - 14.1 Nm).
7. Adjust the proper belt tension.
8. Retighten the motor mounting bolts. Torque to
20-25 ft.-lbs (27.1–33.9 Nm)
9. Reinstall the outer belt guard. All moving parts
must be guarded.
To Check Air Compressor Pump Intake
and Exhaust Valves
Once a year have a Trained Service Technician check the air
compressor pump intake and exhaust valves.
To Inspect Air Lines and Fittings for Leaks
1. Move the Auto/Off switch to "AUTO (-)" and allow
tank pressure to build. Motor will stop when tank
pressure reaches cut-out” pressure.
2. Move the Auto/Off switch to "OFF (O)" and
unplug unit.
3. Apply a soap solution to all air-line fittings and
connections/piping to look for any leaks.
4. Pull ring on safety valve allowing air to bleed from
the tank until tank pressure is approximately 20 PSI.
Release safety valve ring.
5. Drain water from air tank by opening drain valve on
bottom of tank.
6. Correct any leaks found.
IMPORTANT: Even minor leaks can cause the air
compressor to overwork, resulting in premature
breakdown or inadequate performance.
To Replace Belt
12
ENGLISH
To Check Air Compressor Pump Head
Bolt Torque
The air compressor pump head bolts should be kept properly
torqued. Check the torques of the head bolts after the first five
hours of operation. Torque to 15-20ft.-lbs. (20.3-27.1 Nm).
SERVICE AND ADJUSTMENTS
ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED
MUST BE PERFORMED BY TRAINED SERVICE TECHNICIAN.
WARNING: Risk of unsafe operation. Unit cycles
automatically when power is on. When servicing,
you may be exposed to voltage sources,
compressed air, or moving parts. Before servicing
unit unplug or disconnect electrical supply to the
air compressor, bleed tank of pressure, and allow
the air compressor to cool.
To Replace or Clean Check Valve
1. Release all air pressure from air tank. See Draining
Air Tank in the Maintenance section.
2. Move the Auto/Off switch to "Off (O)", unplug the unit,
and relieve all air pressure from the air tank.
3. Using an adjustable wrench loosen outlet tube nut
at air tank and pump. Carefully move outlet tube
away from check valve.
4. Using an adjustable wrench loosen pressure relief
tube nut at air tank. Carefully move pressure relief
tube away from check valve.
5. Unscrew the check valve (turn counterclockwise)
using a 13/16" open end wrench. Note the
orientation for reassembly.
6. Using a screwdriver, carefully push the valve disc
up and down.
NOTE: The valve disc should move freely up and down on a
spring which holds the valve disc in the closed position, if not,
the check valve needs to be cleaned or replaced.
7. Clean or replace the check valve. A solvent, such as
paint or varnish remover can be used to clean the
check valve.
8. Apply sealant to the check valve threads. Reinstall
the check valve (turn clockwise) to proper
orientation.
9. Replace the pressure release tube. Tighten nuts.
10. Replace the outlet tube and tighten nuts.
11. Perform the Break-in Procedure. See Break-in
Procedure in the Operation section.
Cleaning
WARNING: Blow dirt and dust out of all air vents
with clean, dry air at least once a week. To
minimize the risk of eye injury, always wear
ANSIZ87.1 approved eye protection when
performing this.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth
dampened only with water and mild soap. Never
let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Repairs
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and
adjustment (including brush inspection and
replacement, when applicable) should be
performed by a CRAFTSMAN authorized service
center. Always use identical replacement parts.
Storage
Before you store the air compressor, make sure you do the
following:
1. Review the Maintenance section on the
proceeding pages and perform scheduled
maintenance as necessary.
2. Drain water from air tank. See To Drain Tank
under Maintenance.
WARNING: Water will condense in the air tank. If
not drained, water will corrode and weaken the
air tank causing a risk of air tank rupture.
3. Protect the electrical cord and air hose from
damage (such as being stepped on or run over).
4. Store the air compressor in a clean and dry location.
13
ENGLISH
Limited Warranty
CRAFTSMAN Industrial Tools are warranted from date of
purchase.
2 Year – Limited warranty on oil-lubricated air
compressor pumps.
1 Year – Limited warranty on all other air compressor
components. This warranty is not transferable to
subsequent owners.
CRAFTSMAN will repair or replace, without charge, at
CRAFTMANS’s option, any defects due to faulty materials or
workmanship. For further detail of warranty coverage and
warranty repair information, call 1-(888)-331-4569 or visit
craftsman.com. This warranty does not apply to accessories or
damage caused where repairs have been made or attempted
by others. This warranty also does not apply to merchandise
sold by CRAFTSMAN which has been manufactured by and
identified as the product of another company, such as gasoline
engines. Such manufacturer’s warranty, if any, will apply. ANY
INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS,
DAMAGE OR EXPENSE THAT MAY RESULT FROM ANY
DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCT IS
NOT COVERED BY THIS WARRANTY. Some states do not
allow the exclusion of limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply
to you. IMPLIED WARRANTIES, INCLUDING THOSE OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF
ORIGINAL PURCHASE. Some states do not allow limitations
on how long an implied warranty lasts, so the above
limitations may not apply to you.
What the Company Will Do: (the company) will cover parts
and labor to remedy substantial defects due to materials and
workmanship during the first year of ownership, with the
exceptions noted below. Parts used in repair of whole goods or
accessories are warranted for the balance of the original
warranty period.
What is NOT Covered Under This Warranty? Failures by the
original retail purchaser to install, maintain, and operate said
equipment in accordance with standard industry practices.
Modifications to the product, or tampering with components,
or failure to comply with the specific recommendations of the
Company set forth in the owner's instruction manual, will
render this warranty null and void. The Company shall not be
liable for any repairs, replacements, or adjustments to the
equipment, or any costs for labor performed by the purchaser
without the Company’s prior written approval. The effects of
corrosion, erosion, surrounding environmental conditions,
cosmetic defects, and routine maintenance items, are
specifically excluded from this warranty. Routine maintenance
items such as: oil, lubricants, and air filters, as well as changing
oil, air filters, belt tensioning, etc… fall under the owner’s
responsibility. Additional exclusions include: freight damage,
failures resulting from neglect, accident, or abuse, induction
motors when operated from a generator, oil leaks, air leaks, oil
consumption, leaky fittings, hoses, drain valve, bleeder tubes,
The following components are considered normal wear
items and are not covered after the first year of ownership:
Belts, pulleys, flywheels, check valves, pressure switches, air
unloaders, throttle controls, electric motors, brushes,
regulators, o-rings, pressure gauges, tubing, piping, fittings,
fasteners, wheels, quick couplers, gaskets, seals, air filter
housings, piston rings, connecting rods, and piston seals.
• Labor, service calls, and travel charges, are not covered
after the first year of ownership on stationary compressors
(compressors without handles, or wheels). Repairs
requiring overtime, weekend rates, or any other charges
beyond the standard shop labor rate are not covered.
Time required for orientation training for the service center
to gain access to the product, or additional time due to
inadequate egress.
• Damage caused by incorrect voltage, improperly wired, or
failure to have a certified licensed electrician install the
compressor, will render this warranty null and void.
• Damage caused from inadequate filter maintenance.
• Pump wear or valve damage caused by using oil not
specified.
• Pump wear or damage caused by any contamination.
• Pump wear or valve damage caused by failure to follow
proper maintenance guidelines.
• Operation below proper oil level or operation without oil.
• Gas Engines, if product is equipped with a gas engine, see
engine manual for specific engine manufacturer’s warranty
coverage.
Parts purchased separately: The warranty for parts
purchased separately such as: pumps, motors, etc., are as
follows:
From Date of Purchase
• All single & two stage pump 1 year
• Electric motors 90 days
• Universal motor/pump 30 days
• All other parts 30 days
• No return authorization will be issued for
electrical components once items are installed.
How Do You Get Service? In order to be eligible for service
under this warranty you must be the original retail purchaser,
and provide proof of purchase from one of the Company’s
dealers, distributors, or retail outlet stores. Portable
compressors or components must be delivered, or shipped, to
the nearest Authorized Service Center. All associated freight
costs and travel charges must be borne by the consumer.
Please call our toll free number 1-888-331-4569 for assistance.
14
ENGLISH
Limited Warranty
CRAFTSMAN Industrial Tools are warranted from date of
purchase.
2 Year – Limited warranty on oil-lubricated air
compressor pumps.
1 Year – Limited warranty on all other air compressor
components. This warranty is not transferable to
subsequent owners.
CRAFTSMAN will repair or replace, without charge, at
CRAFTMANS’s option, any defects due to faulty materials or
workmanship. For further detail of warranty coverage and
warranty repair information, call 1-(888)-331-4569 or visit
craftsman.com. This warranty does not apply to accessories or
damage caused where repairs have been made or attempted
by others. This warranty also does not apply to merchandise
sold by CRAFTSMAN which has been manufactured by and
identified as the product of another company, such as gasoline
engines. Such manufacturer’s warranty, if any, will apply. ANY
INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS,
DAMAGE OR EXPENSE THAT MAY RESULT FROM ANY
DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCT IS
NOT COVERED BY THIS WARRANTY. Some states do not
allow the exclusion of limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply
to you. IMPLIED WARRANTIES, INCLUDING THOSE OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF
ORIGINAL PURCHASE. Some states do not allow limitations
on how long an implied warranty lasts, so the above
limitations may not apply to you.
What the Company Will Do: (the company) will cover parts
and labor to remedy substantial defects due to materials and
workmanship during the first year of ownership, with the
exceptions noted below. Parts used in repair of whole goods or
accessories are warranted for the balance of the original
warranty period.
What is NOT Covered Under This Warranty? Failures by the
original retail purchaser to install, maintain, and operate said
equipment in accordance with standard industry practices.
Modifications to the product, or tampering with components,
or failure to comply with the specific recommendations of the
Company set forth in the owner's instruction manual, will
render this warranty null and void. The Company shall not be
liable for any repairs, replacements, or adjustments to the
equipment, or any costs for labor performed by the purchaser
without the Company’s prior written approval. The effects of
corrosion, erosion, surrounding environmental conditions,
cosmetic defects, and routine maintenance items, are
specifically excluded from this warranty. Routine maintenance
items such as: oil, lubricants, and air filters, as well as changing
oil, air filters, belt tensioning, etc… fall under the owner’s
responsibility. Additional exclusions include: freight damage,
failures resulting from neglect, accident, or abuse, induction
motors when operated from a generator, oil leaks, air leaks, oil
consumption, leaky fittings, hoses, drain valve, bleeder tubes,
and transfer tubes.
The following components are considered normal wear
items and are not covered after the first year of ownership:
Belts, pulleys, flywheels, check valves, pressure switches, air
unloaders, throttle controls, electric motors, brushes,
regulators, o-rings, pressure gauges, tubing, piping, fittings,
fasteners, wheels, quick couplers, gaskets, seals, air filter
housings, piston rings, connecting rods, and piston seals.
• Labor, service calls, and travel charges, are not covered
after the first year of ownership on stationary compressors
(compressors without handles, or wheels). Repairs
requiring overtime, weekend rates, or any other charges
beyond the standard shop labor rate are not covered.
Time required for orientation training for the service center
to gain access to the product, or additional time due to
inadequate egress.
• Damage caused by incorrect voltage, improperly wired, or
failure to have a certified licensed electrician install the
compressor, will render this warranty null and void.
• Damage caused from inadequate filter maintenance.
• Pump wear or valve damage caused by using oil not
specified.
• Pump wear or damage caused by any contamination.
• Pump wear or valve damage caused by failure to follow
proper maintenance guidelines.
• Operation below proper oil level or operation without oil.
• Gas Engines, if product is equipped with a gas engine, see
engine manual for specific engine manufacturer’s warranty
coverage.
Parts purchased separately: The warranty for parts
purchased separately such as: pumps, motors, etc., are as
follows:
From Date of Purchase
• All single & two stage pump 1 year
• Electric motors 90 days
• Universal motor/pump 30 days
• All other parts 30 days
• No return authorization will be issued for
electrical components once items are installed.
How Do You Get Service? In order to be eligible for service
under this warranty you must be the original retail purchaser,
and provide proof of purchase from one of the Company’s
dealers, distributors, or retail outlet stores. Portable
compressors or components must be delivered, or shipped, to
the nearest Authorized Service Center. All associated freight
costs and travel charges must be borne by the consumer.
Please call our toll free number 1-888-331-4569 for assistance.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO
STATE. THE COMPANY MAKES NO OTHER WARRANTY OR
REPRESENTATION OF ANY KIND WHATSOEVER, EXPRESSED OR
IMPLIED, EXCEPT THAT OF TITLE. ALL IMPLIED WARRANTIES,
INCLUDING ANY WARRANTY OF MERCHANTABILITY AND
FITNESS FOR PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
LIABILITY FOR CONSEQUENTIAL AND INCIDENTAL DAMAGES
UNDER ANY AND ALL WARRANTIES, OTHER CONTRACTS,
NEGLEGENCE, OR OTHER TORTS IS EXCLUDED TO THE EXTENT
EXCLUSION IS PERMITTED BY LAW.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-888-331-4569
for a free replacement.
ATENCION
E106191
RISK OF BURSTING
PREVENT TANK CORROSION. AFTER EACH
USAGE, DRAIN ALL MOISTURE FROM TANK.
DRAIN VALVE LOCATED ON BOTTOM OF TANK. DRENAR LA VÁLVULA UBICADA DEBAJO DEL TANQUE . SOUPAPE DE VIDANGE SITUÉE SUR LE DESSOUS DU RÉSERVOI.
RISQUE D’ÉCLATEMENT
PRÉVENIR LA CORROSION EN DRAINANT TOUTE HUMIDITÉ
DU RÉSERVOIR APRÈS CHAQUE USAGE.
RIESGO DE EXPLOSIÓN
PREVENIR LA CORROSIÓN DEL TANQUE. DESPUÉS DE CADA USO
DRENAR TODA HUMEDAD DEL TANQUE.
HOT SURFACE. RISK OF
BURNS. DO NOT TOUCH.
SUPERFICIE CALIENTE.
RIESGO DE QUEMADURAS.
NO TOCAR.
È
RISQUES DE BRÛLURES.
NE PAS TOUCHER.
N0 088 06
SUURFACE TR S CHAUDE.
PROBLEM CAUSE CORRECTION
The compressor does not run.
The tank has insufficient pressure.
There is no electrical power to the unit.
The circuit breaker has tripped or a fuse
has blown at the main power source.
The thermal overload protector is
actuated.
There is loss of power or overheating.
The pressure switch is bad.
When the tank pressure drops, the compressor will turn on to
cut-in pressure.
Verify the wiring connection inside the pressure switch and the
terminal box area.
Check the fuse/breaker to determine the underlying cause.
Turn the air compressor OFF ( O ).
Wait until the compressor cools down.
Depress the red reset button on the motor.
Turn the air compressor to AUTO (-).
Verify the wiring.
NOTE: Long lengths of electrical wiring could cause power loss
to the motor.
Replace the pressure switch.
The motor hums while running slowly,
or it does not run at all.
There is low voltage from the power
source.
There are loose electrical connections.
There is a shorted or open motor wiring.
There is a defective check valve or
unloader.
Check the voltage with a voltmeter.
Verify the wiring connections inside the pressure switch and
the terminal box area is secure.
Bring the compressor to a service center.
Bring the compressor to a service center.
The compressor is making squealing
sounds.
The compressor pump has no oil.
The belt is too loose.
Check the pump oil.
Check the belt tension.
The compressor is experiencing
restricted air intake
The air filter is dirty.
The compressor is making knocking
sounds.
There is a loose pulley.
There is a loose flywheel.
The compressor mounting screws are
loose.
The belt is too loose.
An excessive amount of carbon has built-
up in the pump.
The belt is too tight.
Clean or replace the air filter.
Tighten the pulley set screws.
Tighten the flywheel screw.
Tighten the mounting screws.
Check the belt tension.
Bring the compressor to a service center.
Check the belt tension.
ENGLISH
TROUBLESHOOTING
WARNING: Risk of Unsafe Operation. Unit cycles automatically when power is on. When servicing, you
may be exposed to voltage sources, compressed air, or moving parts. Before servicing unit, unplug or
disconnect electrical supply to the air compressor, bleed tank of pressure, and allow the air compressor
to cool.
15
PROBLEM CAUSE CORRECTION
The compressor does not run.
The tank has insufficient pressure.
There is no electrical power to the unit.
The circuit breaker has tripped or a fuse
has blown at the main power source.
The thermal overload protector is
actuated.
There is loss of power or overheating.
The pressure switch is bad.
When the tank pressure drops, the compressor will turn on to
cut-in pressure.
Verify the wiring connection inside the pressure switch and the
terminal box area.
Check the fuse/breaker to determine the underlying cause.
Turn the air compressor OFF ( O ).
Wait until the compressor cools down.
Depress the red reset button on the motor.
Turn the air compressor to AUTO (-).
Verify the wiring.
NOTE: Long lengths of electrical wiring could cause power loss
to the motor.
Replace the pressure switch.
The motor hums while running slowly,
or it does not run at all.
There is low voltage from the power
source.
There are loose electrical connections.
There is a shorted or open motor wiring.
There is a defective check valve or
unloader.
Check the voltage with a voltmeter.
Verify the wiring connections inside the pressure switch and
the terminal box area is secure.
Bring the compressor to a service center.
Bring the compressor to a service center.
The compressor is making squealing
sounds.
The compressor pump has no oil.
The belt is too loose.
Check the pump oil.
Check the belt tension.
The compressor is experiencing
restricted air intake
The air filter is dirty.
The compressor is making knocking
sounds.
There is a loose pulley.
There is a loose flywheel.
The compressor mounting screws are
loose.
The belt is too loose.
An excessive amount of carbon has built-
up in the pump.
The belt is too tight.
Clean or replace the air filter.
Tighten the pulley set screws.
Tighten the flywheel screw.
Tighten the mounting screws.
Check the belt tension.
Bring the compressor to a service center.
Check the belt tension.
ENGLISH
TROUBLESHOOTING
WARNING: Risk of Unsafe Operation. Unit cycles automatically when power is on. When servicing, you
may be exposed to voltage sources, compressed air, or moving parts. Before servicing unit, unplug or
disconnect electrical supply to the air compressor, bleed tank of pressure, and allow the air compressor
to cool.
16
ENGLISH
There is excessive belt wear. The belt is too loose.
The belt is too tight.
The pulley is loose.
The pulley is misaligned.
Check the belt tension.
Check the belt tension.
Align the pulley/flywheel. Correct the belt tension. Torque
the set screws.
Align the pulley/flywheel.
Tank is slow to build pressure or will not
build pressure
The connections (fittings, tubing, etc.) are
loose and leaking.
The drain valve is loose or open.
The check valve is leaking.
Check all the connections with a soap and water solution
and tighten.
Tighten the drain valve.
Bring the compressor to a service center.
There is excessive moisture in the discharge
air.
There is excessive water in the air tank.
The oil blow-by has accumulated in
the pump.
It is normal for oil lube air compressor pumps to release
some oil into the tank and air lines. Air compressors will also
generate water condensation that will form in the tank and
air lines. Install water and oil filter traps when needed. The
Typical Compressed Air Distribution System section provides
a guideline. Contact or call Crafstman Customer Service for more
information.
IMPORTANT: If the tank or air lines have excessive water and/or
oil, bring the compressor to a service center.
The fuses blow or the circuit breaker trips
repeatedly.
The incorrect fuse size is being used, or
the circuit is overloading.
There are loose electri
cal connections.
There is a defective check valve or
unloader.
Verify the proper fuse size is being used.
Use time-delay fuses.
Disconnect other electrical appliances from the circuit or
operate the compressor on its own branch circuit.
Verify the wiring connection inside the pressure switch and the
terminal box area.
Bring the compressor to a service center.
Clean or replace check valve
PROBLEM CAUSE CORRECTION
17
FRANÇAIS
Définitions : Symboles et termes de mise en garde liée à la sécurité
Ce mode d’emploi utilise les symboles et termes de mise en garde liée à la sécurité suivants pour vous avertir en cas de
situation dangereuse et de risque de blessure corporelle ou de dommages matériels.
DANGER: Indique une situation dangereuse imminente qui, si elle n’est pas évitée, résultera en mort d’homme ou des
blessures graves.
AVERTISSEMENT:
Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, peut résulter en mort
d’homme ou des blessures graves.
ATTENTION:
Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait résulter en des
blessures mineures ou modérées.
(Utilisé sans mot) Indique un message relatif à la sécurité.
AVIS: Indique une pratique non associée à des blessures corporelles qui, si elle n’est pas évitée, pourrait résulter
en des dommages matériels.
.
Surfaces très chaudes
Pompe de compresseur
9
8
10
6
7
Fig. A
16
15
14
13
11
12
4
5
1
3
2
AVERTISSEMENT: Lisez tous les avertissements
relatifs à la sécurité et toutes les instructions. Tout
manquement à respecter les avertissements et les
instructions peut entraîner un choc électrique, un
incendie et/ou des blessures graves
AVERTISSEMENT: Ne modifiez jamais le produit ni
aucune de ses pièces. Cela pourrait entraîner des
dommages matériels ou des blessures corporelles.
AVERTISSEMENT: Pour réduire les risques de
blessures corporelles, lisez le mode d’emploi.
Pour toute question ou commentaire concernant
ce produit ou tout autre produit, veuillez
composer le numéro gratuitde CRAFTSMAN:
1-888-331-4569
Composants
Interrupteur Auto/arrêt
Pressostat (non illustré)
Soupape de sûreté
Manomètre du réservoir
Clapet anti-retour
Filtre d’entrée d’air
Pompe du compresseur d’air
Robinet de purge
Sortie d’air
Dispositif de protection du moteur
contre les surcharges
Tête de pompe du compresseur
Cylindre de pompe du compresseur
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Tube de sortie
Bouchon de remplissage de
l’huile
Regard d’huile
Bouchon de vidange de
l’huile
ATTENTION
18
Compresseur d’air
CMXECXM601
CONSERVEZ TOUS LES
AVERTISSEMENTS ET INSTRUCTIONS
POUR UNE RÉFÉRENCE ULTÉRIEURE
DANGER: RISQUE D’EXPLOSION OU D’INCENDIE
Ce qui peut arriver
Comment l’éviter
Il est normal que les contacts
électriques au sein du moteur et
du pressostat produisent des
étincelles.
Utilisez toujours le compresseur
dans un emplacement bien aéré et
exempt de matières combustibles,
d’essence ou de vapeurs de solvants.
Si des étincelles électriques du
compresseur entrent en contact
avec des vapeurs inflammables,
elles pourraient prendre feu et
causer un incendie ou une explosion.
Si vous pulvérisez des matières
inflammables, placez le compresseur
à au moins 6,1 m (20 pi) de l’espace
de pulvérisation. Il se peut que vous
ayez besoin d’une longueur de boyau
supplémentaire.
Entreposez les matières inflammables
dans un emplacement sécurisé et
éloigné du compresseur.
L’obstruction de tout orifice de
ventilation du compresseur causera
une surchauffe sérieuse et pourrait
entraîner un incendie.
Ne placez jamais d’objets contre ou
sur la pompe du compresseur.
Utilisez le compresseur dans un
espace ouvert à une distance d’au
moins 30,5 cm (12 po) de tout mur
ou objet qui pourrait limiter le flux
d’air frais aux orifices de ventilation.
Installez le compresseur dans un
espace propre, sec et bien aéré.
N’utilisez pas l’appareil à l’intérieur
ou dans tout espace confiné.
Un fonctionnement non surveillé de
ce produit pourrait entraîner des
blessures ou des dommages
matériels. Pour réduire les risques
d’incendie, ne laissez pas le
compresseur fonctionner sans
surveillance.
Restez toujours présent(e) auprès du
produit pendant qu’il est en marche.
Éteignez et débranchez toujours
l’appareil lorsqu’il n’est pas utilisé.
ATTENTION: RISQUE ASSOCIÉ AU BRUIT
Ce qui peut arriver
Comment l’éviter
Dans certaines conditions et durées
d’utilisation, le bruit émit par ce
produit peut entraîner une perte
auditive.
Portez toujours un équipement de
protection accrédité : Protection
auriculaire conforme à la norme
ANSI S12.6 (S3.19).
DANGER: RISQUES À LA RESPIRATION
(Asphyxie)
Ce qui peut arriver Comment l’éviter
L’air comprimé provenant
directement de votre compresseur
est impropre à la respiration. Ce flux
d’air pourrait contenir du monoxyde
de carbone, des vapeurs toxiques
ou des particules solides provenant
du réservoir d’air. Respirer ces
contaminants peut entraîner des
blessures graves, voire la mort.
L’air issu directement du compresseur
ne doit jamais être utilisé pour fournir
de l’air à des fins de consommation
humaine. Afin d’utiliser l’air produit
par ce compresseur pour la respiration,
il faut installer correctement des filtres
et un équipement de sûreté en ligne
appropriés. Les filtres et l’équipement
de sûreté en ligne utilisés conjointement
avec le compresseur doivent pouvoir
traiter l’air conformément à tous les
codes locaux et fédéraux applicables
avant toute consommation humaine.
Une exposition aux produits
chimiques dans la poussière produite
par le ponçage mécanique, le sciage,
le broyage, le perçage et d’autres
activités de construction peut
s’avérer dangereuse.
Travaillez dans un espace doté d’une
ventilation correcte. Lisez et respectez
les consignes de sécurité indiquées
sur l’étiquette ou les fiches de données
de sécurité pour les matériaux que vous
pulvérisez. Utilisez toujours un
équipement de protection accrédité :
Équipement de protection des voies
respiratoires homologué par
OSHA/MSHA/NIOSH et conçu pour
une utilisation avec votre application
particulière.
Les matériaux pulvérisés, tels que la
peinture, les solvants, les décapants,
les insecticides et les herbicides
peuvent contenir des vapeurs et
poisons dangereux.
AVERTISSEMENT: RISQUE D’ÉCLATEMENT
Réservoir d’air: Le 26février2002, la commission
américaine pour la sécurité des produits de consommation
(U.S. Consumer Product Safety Commission) a publié le
Communiqué nº02-108 concernant la sécurité des réservoirs
de compresseurs d’air:
Les réservoirs récepteurs de compresseurs d’air n’ont pas une
durée de vie infinie. La durée de vie du réservoir dépend de
divers facteurs, notamment des conditions de fonctionnement,
des conditions ambiantes, des installations correctes, des
modifications sur place et du niveau d’entretien. L’effet exact
de ces facteurs sur la vie du réservoir de réception d’air est
difficile à prévoir.
Si les procédures d’entretien correct ne sont pas suivies, une
corrosion interne de la paroi intérieure du réservoir de réception
d’air peut entraîner la rupture brusque du réservoir d’air,
permettant ainsi à l’air sous pression de s’échapper
soudainement en force, et poser un risque de blessures aux
utilisateurs.
Le réservoir de votre compresseur d’air doit être mis hors
service à la fin de l'année indiquée sur l'étiquette
d'avertissement de votre réservoir.
Les conditions suivantes peuvent entraîner un affaiblissement
du réservoir d’air et causer une explosion violente du réservoir
d’air:
AVERTISSEMENT:
CONTIENT DU PLOMB. Peut être nocif si consommé ou mâché.
Peut produire de la poussière à teneur en plomb.Lavez vos
mains après l’utilisation. Gardez hors de la portée des enfants
AVERTISSEMENT:
Ce produit peut vous exposer à des produits chimiques, y
compris le plomb qui est reconnu par l’état de la Californie
comme pouvant causer le cancer, des anomalies congénitales
ou d’autres dommages aux fonctions reproductrices.
Pour obtenir des renseignements supplémentaires, allez sur
FRANÇAIS
Ce qui peut arriver Comment l’éviter
Un manquement à purger
correctement l’eau condensée du
réservoir d’air cause la rouille et
un amincissement du réservoir
d’air en acier.
Purgez le réservoir d’air chaque jour
ou après chaque utilisation. Si une
fuite apparaît dans le réservoir d’air,
remplacez-le immédiatement par
un nouveau réservoir d’air ou
remplacer le compresseur tout entier.
Modifications ou tentatives de
réparation du réservoir d’air.
Ne percez et ne soudez jamais le
réservoir d’air ni aucun de ses
accessoires et ne leur apportez jamais
de modifications.Ne tentez jamais de
réparer un réservoir d’air endommagé
ou qui fuit Remplacez-le par un
nouveau réservoir d’air.
Modifications non autorisées
apportées à la soupape de sécurité
ou tout autre composant qui
contrôle la pression du réservoir
d’air.
Le réservoir d’air est conçu pour
résister à des pressions de
fonctionnement spécifiques.
N’effectuez jamais de réglages ou
de remplacements de pièces pour
modifier les pressions de
fonctionnement établies en usine.
Accessoires:
Dépasser la pression nominale des
outils pneumatiques, des pistolets
pulvérisateurs, des accessoires
fonctionnant à l’air, des pneus et a
utres articles gonflables peut les
faire exploser ou se détacher et
voler, et pourrait entraîner des
blessures graves.
Suivez les recommandations du
fabricant de l’équipement et ne
dépassez jamais la pression nominale
maximum autorisée des accessoires.
N’utilisez jamais le compresseur pour
gonfler les petits objets à basse
pression, tels que les jouets d’enfants,
les ballons de football, les ballons de
basketball, etc.
Pneus:
Trop gonfler les pneus peut être
cause de blessures graves et de
dommages matériels.
Servez-vous d’un manomètre pour
pneus pour vérifier la pression des
pneus avant chaque utilisation et
pendant que vous gonflez les pneus;
regardez la paroi latérale du pneu
pour connaître la pression de pneu
correcte.
REMARQUE : Les réservoirs d’air,
compresseurs et équipements
semblables utilisés pour gonfler les
pneus peuvent remplir très
rapidement les petits pneus
semblables à ceux-ci. Réglez le
régulateur de pression de
l’alimentation en air pas plus
haut que la pression nominale des
pneus. Ajoutez l’air à petites doses
et utilisez fréquemment le
manomètre pour pneus pour éviter
de trop gonfler.
AVERTISSEMENT: RISQUE DE
CHOC ÉLECTRIQUE
Ce qui peut arriver Comment l’éviter
Votre compresseur d’air est
alimenté par l’électricité. Comme
tout autre dispositif alimenté par
l’électricité, il peut causer un choc
électrique s’il n’est pas utilisé
correctement.
N’utilisez jamais le compresseur à
l’extérieur quand il pleut ou par
conditions mouillées.
N’utilisez jamais le compresseur si les
couvercles de protection sont retirés
ou endommagés.
Les réparations tentées par un
personnel non qualifié peut
entraîner des blessures graves,
voire la mort par électrocution.
Toute réparation requise pour ce
produit doit être effectuée par un
employé du centre de service
autorisé.
Mise à la terre : Un manquement
à fournir une mise à la terre adéquate
pour ce produit pourrait entraîner
des blessures graves, voire la mort
par électrocution Voir Instructions
de mise à la terre sous Installation.
Assurez-vous que le circuit
électrique sur lequel le compresseur
est branché fournit la mise à la terre
appropriée, la tension correcte
et une protection par fusibles
adéquate.
AVERTISSEMENT: RISQUES ASSOCIÉS
AUX OBJETS VOLANTS
Ce qui peut arriver Comment l’éviter
Le flux d’air comprimé peut
endommager le tissu mou de la
peau exposée et peut projeter de
la saleté, des éclats, des particules
libres et des petits objets à grande
vitesse, causant ainsi des dommages
matériels ou blessures corporelles.
Portez toujours un équipement de
protection accrédité : Lunettes de
protection ANSI Z87.1
(CAN/CSA Z94.3) avec écrans latéraux
pendant l’utilisation du compresseur.
N’orientez jamais une buse ou un
pulvérisateur vers une partie
quelconque du corps ou en direction
d’autres personnes ou animaux.
Éteignez toujours le compresseur et
purgez la pression du boyau d’air et
du réservoir d’air avant de tenter
l’entretien ou de fixer des outils
ou accessoires.
AVERTISSEMENT: RISQUE POSÉ PAR LES
SURFACES TRÈS CHAUDES
Ce qui peut arriver Comment l’éviter
Toucher un métal exposé tel que la
tête du compresseur, la tête du
moteur, le tuyau d’échappement
ou les tubes de sortie, peut entraîner
des brûlures graves.
Ne touchez jamais les pièces en métal
exposées sur le compresseur pendant
ou immédiatement après utilisation.
Le compresseur restera chaud pendant
plusieurs minutes après son utilisation.
N’attrapez rien autour des écrans
protecteurs et ne tentez aucun entretien
sans avoir laissé à l’appareil le temps
de refroidir.
AVERTISSEMENT: RISQUES DE BLESSURES
RÉSULTANT DU LEVAGE
Ce qui peut arriver Comment l’éviter
Une blessure grave peut résulter
d’une tentative de levage d’un
objet trop lourd.
Le compresseur est trop lourd pour
être soulevé par une seule personne.
Faites-vous aider par d’autres
personnes avant de soulever.
AVERTISSEMENT: RISQUES ASSOCIÉS AUX
PIÈCES MOBILES
Ce qui peut arriver Comment l’éviter
Les pièces mobiles tels que la poulie,
le volant et la courroie peuvent
causer des blessures graves, si elles
entrent en contact avec vous ou vos
vêtements.
N’utilisez jamais le compresseur avec
des protections ou couvercles
endommagés ou manquants.
Gardez les cheveux, les vêtements et
les gants à l’écart des pièces mobiles.
Les vêtements amples, bijoux ou
cheveux longs pourraient se prendre
dans les pièces mobiles.
Des évents peuvent couvrir des pièces
mobiles et il faut les éviter également.
AVERTISSEMENT: RISQUE D’ÉCLATEMENT
(suite)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50

Craftsman CMXECXM601 Manuel utilisateur

Catégorie
Compresseurs d'air
Taper
Manuel utilisateur