dji Avata QF2W4K Drone Camera Mode d'emploi
- Taper
- Mode d'emploi
DJI Avata Quick Start Guide
v1.0
Product Overview
Aircraft
1. Intelligent Flight Battery
2. Battery Buckles
3. Aircraft LEDs and Status Indicator
4. Gimbal and Camera
5. Power Button
6. Battery Level LEDs
7. Battery Port
8. USB-C Port
9. microSD Card Slot
10. Downward Vision System and Infrared Sensing System
Goggles
1. Antennas
2. Headband Attachment
3. Channel Display
4. IPD Knob
5. Touch Panel
6. AC Power Cable Slot
7. USB-C Port
8. Link Button
9. Audio Port
10. microSD Card Slot
Smart Controller
1. Battery Level LEDs
2. Lock Button
3. Mode Button
4. Flight Pause Button
5. Gimbal Tilt Slider
6. Shutter/Record Button
7. Accelerator
8. Lanyard Hole
9. USB-C Port
10. Power Button
Initial Setup
Download the DJI Fly App, and watch the tutorial videos.
Preparing the aircraft
1. Remove the gimbal protector.
Preparing the Goggles
1. Unfold the antennas.
2. Attach the headband to the goggles and adjust the headband size.
3. Use the included power cable to connect the power port of the goggles to the goggles battery.
4. Slide the IPD knob left and right to adjust the interpupillary distance （56 - 72 mm）, press and rotate the IPD knob to adjust the diopter （+2.0 D to -8.0
D). After all preparations are completed and the all devices turned on, adjust this knob to obtain a clear view.
Check Battery Level, Power on/off
Check battery level: press once.
Power on/off: press then press and hold.
Linking
Follow the steps below to link the aircraft, goggles, and smart controller: The aircraft must be linked with the goggles before the smart
controller.
1. Power on the aircraft, goggles, and smart controller.
2. Press the link button on the goggles. The goggles will start to beep continually.
3. Press and hold the power button of the aircraft until the battery level LEDs start to blink in sequence.
4. The battery level LEDs of the aircraft turn solid and display the battery level. The goggles stop beeping when they are successfully linked
and the video display is normal.
5. Press and hold the power button of the aircraft until the battery level LEDs start to blink in sequence.
6. Press and hold the power button of the smart controller until it starts to beep continually and the battery level LEDs blinks in sequence.
7. Once linking is successful, the smart controller stops beeping and both the battery level LEDs turn solid and display the battery level.
Activating the Aircraft
New products must be activated before using for the first time. Power on the aircraft, goggles, and smart controller. Connect the USB-C port of
the goggles to the mobile device, run DJI Fly, and follow the prompts to activate. An internet connection is required for activation.
Operation
Buttons
1. Lock Button
Press twice to start the motors of the aircraft.
Press and hold to make the aircraft automatically take off, ascend to approximately 1
m, and hover.
Press and hold while hovering to make the aircraft automatically land and the motors
to stop.
Press once to cancel Low Battery RTH when the countdown appears in the goggles.
Critical Low Battery landing cannot be canceled.
2. Brake Button
Press once to make the aircraft brake and hover in place.
If the aircraft is performing RTH or auto landing, press once to exit RTH.
Press and hold the brake button until the smart controller beeps to indicate that RTH
has started. Press the button again to cancel RTH.
3. Mode Button
The smart controller has two modes: Normal mode and Sport mode. Normal mode is
selected by default. Press once to switch between Normal and Sport mode. The current
mode is displayed in the goggles.
4. Gimbal Tilt Slider
push up and down to adjust the tilt of the gimbal (only available before takeoff).
5. Shutter/Record Button
press once to take a photo or to start or stop recording.
Press and hold to switch between photo and video mode.
Control motion
Charging the Intelligent Flight Battery
1. Take out the Intelligent Flight Battery.
2. Connect the Intelligent Flight Battery to the charging hub and then connect the charging hub to power outlet.
3. Install the Intelligent Flight Battery back.
Specifications
Aircraft (model no# QF2W4K)
Takeoff Weight
Approx. 399 g
Operating Temperature
14° to 104° F (-10° to 40° C)
O3+
Operating Frequency
2.400~2.4835 GHz（RX Only）; 5.725~5.850 GHz
Transmitter Power (EIRP)
5.8 GHz: < 33 dBm (FCC), < 30 dBm (SRRC), < 14 dBm (CE)
Intelligent Flight Battery
Capacity
2420 mAh
Standard Voltage
14.76 V
Battery Type
Li-ion
Chemical System
LiNiMnCoO2
Charging Temperature
41° to 104° F (5° to 40° C)
Max Charging Power
65 W
Compliance Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding
the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. This transmitter
must not be co-located or operating in conjunction with any other antenna or transmitter.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment
ISED Compliance Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's
licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must
accept any interference, including interference that may cause undesired operation of the device.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :(1)L'appareil
ne doit pas produire de brouillage; (2)L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
This equipment complies with RSS‐102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Cet équipement est conforme aux limites d'exposition aux radiations CNR‐102 établies pour un environnement non contr?lé. Cet équipement
doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific
operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.The portable device is designed to meet the requirements for exposure to radio waves established by the ISED.
EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential requirements
and other relevant provisions of the Directive 2014/53/EU.
A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance
EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany
GB Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential requirements
and other relevant provisions of Radio Equipment Regulations 2017.
A copy of the GB Declaration of Conformity is available online at www.dji.com/euro-compliance
In order to avoid the possibility of exceeding the radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm
during normal operation
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The
disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the
appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable
raw materials and the treatment of toxic substances.
Thailand Warning message
.
Mexico Warning message
“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia
perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.”
Brazil Warning message
Informações sobre Regulamentação
Estes equipamentos estão certificados e homologados pela ANATEL.
Para maiores informações, consulte o site da ANATEL: www.anatel.gov.br.
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar
interferência em sistemas devidamente autorizados.
Este produto está homologado pela Anatel de acordo com os procedimentos regulamentados para
avaliação da conformidade de produtos para telecomunicações e atende aos requisitos técnicos aplicados, incluindo os limites de exposição da
Taxa de Absorção Específica referente a campos
elétricos, magnéticos e eletromagnéticos de radiofrequência.
-
1
-
2
-
3
-
4
-
5
-
6
dji Avata QF2W4K Drone Camera Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
dji O3 Air Unit Mode d'emploi
-
dji MT2PD2007 Camera Drone Mode d'emploi
-
dji FPV Mode d'emploi
-
dji B08YR48SZ1 Air 2S Drone Quadcopter Mode d'emploi
-
-
-
-
dji Assistant 2 For Mavic Mode d'emploi
-
-
dji AIR 2S Mode d'emploi
