Skil LT4823B-10 Manuel utilisateur

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

Owner’s Manual

Guide d’utilisation

Manual del propietario

For Customer Service

Pour le service à la clientèle

Servicio al cliente

1-877-SKIL-999

OR

www.skil.com

20V 13'' Brushless String Trimmer

Taille-haie sans balai de 20 V et 33 cm / 13 po

Orilladora de hilo sin escobillas de 13 pulgadas de 20 V

Model/ Modelo/ Modèle: LT4823B-00

2

TABLE OF CONTENTS

Important Safety Instructions ....................................3-5

Symbols .....................................................6-8

Get to Know Your String Trimmer ...............................9-10

Specications .................................................10

Recommended Accessory .......................................10

Assembly ..................................................11-13

Operating Instructions .......................................14-19

Maintenance ................................................ 20-22

Troubleshooting ............................................23-24

Limited Warranty of SKIL Consumer Tools ..........................25

3

IMPORTANT SAFETY INSTRUCTIONS

WARNING

Read all safety warnings, instructions, illustrations and specifications

provided with this power tool.

Failure to follow all instructions listed

below may result in electric shock, re and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

WARNING

When using electric trimmers, basic safety precautions should

always be followed to reduce the risk of fire, electric shock, and

personal injury, including the following:

Do not rely on the tool’s insulation against electric shock. To reduce the risk of

electrocution, never operate the tool in the vicinity of any wires or cables which may

carry electric current.

Wear appropriate personal hearing protection during use.

Under some conditions and

durations of use, noise from this product may contribute to hearing loss.

Keep children, other persons and pets away

. All visitors should be kept at least 100 feet (30

m) away from work area.

Avoid dangerous environments.

Don’t use trimmers on damp or wet slope.

Dress properly.

Do not wear loose clothing or jewelry. They can be caught in moving parts.

Use of rubber gloves and substantial footwear is recommended when working outdoors. Wear

protective hair covering to contain long hair.

Use safety glasses. Always use face or dust mask if operation is dusty.

Use the right tool

. Do not use the tool for any job except that for which it is intended.

Don’t force the trimmer

. It will do the job better and with less likelihood of a risk of injury at

the rate for which it was designed.

Don’t overreach. Keep proper footing and balance at all times.

Stay alert . Watch what you are doing. Use common sense. Do not operate the trimmer

when you are tired.

Do not operate the trimmer while under the influence of alcohol or drugs.

Keep guards in place and in working order.

Keep hands and feet away from the cutting area.

Store trimmer indoors and out of reach of children

. When not in use the trimmer should be

stored indoors in a dry and high, and locked-up place with the battery pack removed.

Maintain trimmer with care.

Keep the cutting attachment clean for best performance

and to reduce the risk of injury. Follow the instructions for changing accessories. Keep

the handles dry, clean, and free from oil and grease.

Check damaged parts.

Before further use of the trimmer, a guard or other part that is

damaged should be carefully checked to determine that it will operate properly and perform

its intended function. Check for alignment of moving parts, binding of moving parts, breakage

of parts, mounting, and any other condition that may affect its operation. A guard or other

part that is damaged should be properly repaired or replaced by an authorized service center

unless indicated elsewhere in this manual.

Clear the area to be cut before each use.

Remove all objects such as rocks, broken glass,

nails, wire, or string that can be thrown or become entangled in the cutting attachment.

Always hold the trimmer firmly, with both hands on the handles, while operating.

Wrap

your ngers and thumbs around the handles.

Avoid accidental starting.

Don’t carry the trimmer with your nger on the trigger.

4

Do not operate the trimmer in gaseous or explosive atmospheres.

Motors in these

appliances create sparks, and the sparks might ignite fumes.

If you strike a foreign object with the trimmer or it becomes entangled, stop the tool

immediately, check for damage and have any damage repaired before further operation

is attempted. Do not operate with a broken guard or spool.

DANGER

If the trimmer should start to vibrate abnormally, stop the motor and

check immediately for the cause.

Vibration is generally a warning of

trouble. A loose head may

vibrate, crack, break or come off the trimmer, which may result in

serious or fatal injury. Make

sure that the cutting attachment is properly xed in position. If the

head loosens after xing it

in position, replace it immediately. Never use a trimmer with a loose

cutting attachment.

DANGER

Replace a cracked, damaged or worn-out cutting head immediately,

even if damage is limited to superficial cracks.

Such attachments may

shatter at high speed and cause

serious or fatal injury.

Check the cutting attachment at regular short intervals during operation, or immediately

if there is a noticeable change in cutting behavior.

When replacing the cutting line, use the nylon line with thickness of no more than 0.08

in (2 mm).

Using heavier lines than recommended by the manufacturer increases the load

on the motor and reduces its operating speed. This results in overheating and damage to the

trimmer.

To reduce the risk of serious injury, never use wire or metal-reinforced line or other

material in place of the nylon cutting lines.

Pieces of wire could break off and be thrown at

high speed toward the operator or bystanders.

To reduce the risk of injury from loss of control, never work on a ladder or on any other

insecure support. Never hold the cutting attachment above waist height.

If situations occur that are not covered in this manual, use care and good judgment.

Contact the SKIL Customer Service Center for assistance.

Do not charge the battery pack in rain, or in wet locations.

Recharge only with the charger specified by the manufacturer.

A charger that is suitable

for one type of battery pack may create a risk of re when used with another battery pack.

Use this trimmer only with specifically designated battery packs.

Use of any other battery

packs may create a risk of injury and re.

When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection

from one terminal to another.

Shorting the battery terminals together may cause burns or a

re.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water.

If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause irritation or burns.

Do not use a battery pack or appliance that is damaged or modified.

Damaged or

modied batteries may exhibit unpredictable behavior resulting in re, explosion or risk of

injury.

Follow all charging instructions and do not charge the battery pack or appliance

outside of the temperature range specified in the instructions.

Charging improperly or at

temperatures outside of the specied range may damage the battery and increase the risk of

re.

Do not dispose of the battery in a fire.

The cells may explode. Check with local codes for

possible special disposal instructions.

Do not open or mutilate the battery.

Released electrolyte is corrosive and may cause

damage to the eyes or skin. It may be toxic if swallowed.

5

Exercise care in handling batteries in order not to short the battery with conducting

materials such as rings, bracelets, and keys.

The battery or conductor may overheat and

cause burns.

Replacement Parts

- When servicing, use only identical SKIL replacement parts. Use of any

other accessory or attachment may increase the risk of injury.

Battery tools do not have to be plugged into an electrical outlet; therefore, they are

always in operating condition.

Be aware of possible hazards even when the tool is not

operating. Take care when performing maintenance or service.

Disconnect the battery pack from the appliance before making any adjustments,

changing accessories, or storing appliance.

Such preventive safety measures reduce the

risk of starting the appliance accidentally.

Do not wash with a hose; avoid getting water in motor and electrical connections.

Do not incinerate the appliance even if it is severely damaged.

The batteries can explode

in a re.

Do not expose a battery pack or tool to fire or excessive temperature.

Exposure to re or

temperature above 212 °F (100°C) may cause explosion.

Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to battery pack, picking up or carrying the appliance.

Carrying the appliance

with your nger on the switch or energizing appliance that have the switch on invites

accidents.

Have servicing performed by a qualified repair person using only identical replacement

parts.

This will ensure that the safety of the product is maintained.

Save these instructions.

Refer to them frequently and use them to instruct others who may

use this tool. If you lend this tool to someone else, also lend these instructions to them to

prevent misuse of the product and possible injury.

SAVE THESE INSTRUCTIONS!

6

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and the explanations with them deserve your careful attention and understanding.

The symbol warnings do not, by themselves, eliminate any danger. The instructions and

warnings they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Owner’s

Manual, including all safety alert symbols such as “

DANGER

,”

“

WARNING

,” and “

CAUTION

” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual

and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equipment

or other property damage if they are not followed. Each message is preceded by the word

“NOTICE”, as in the example below:

NOTICE:

Equipment and/or property damage may result if these instructions are not followed.

WARNING

The operation of any power tools can result in foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always

use eye protection which is marked to comply with ANSI Z87.1.

7

SYMBOLS (CONTINUED)

IMPORTANT:

Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-Hours Battery capacity

Ø Diameter Size of drill bits, grinding wheels, etc.

n

0

No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

…/min

Revolutions or reciprocation

per minute

Revolutions, strokes, surface speed, orbits,

etc. per minute

IPX4 Ingress protection degree Protection from splashing water

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Li-ion RBRC seal Designates Li-ion battery recycling program

Read manual symbol Alerts user to read manual

Wear eye protection symbol

Always wear safety goggles or safety

glasses with side shields and a full face

shield when operating this product.

8

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT:

Some of the following symbols for certication information may be used on your

tool. Please study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and more safely.

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this component is recognized by

Underwriters Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican

Standards.

9

GET TO KNOW YOUR STRING TRIMMER

Hinge

Lock-off Button

Rear Handle

Speed Selector

Adjustable Front-Assist Handle

Line-Cutting

Blade

Release Tab

Storage Rail

Storage Hole

Storage Adapter

Trigger Switch

Guard

Cutting Line

Trimmer Head

(Bump Head)

Lower Cover

Fig. 1

10

Adjustable Front-Assist Handle

For easy control of the trimmer during cutting.

Rear Handle

Ergonomic handle improves comfort and grip.

Trigger Switch

Turns the string trimmer on and off.

Speed Selector

This string trimmer gives you the choice to operate at a more efcient speed to extend the

runtime for larger jobs or accelerate the trimmer speed for high-performance cutting.

Lock-off Button

Helps prevent accidental or unauthorized activation of the trigger. It must be depressed before

the trigger can be activated.

Hinge

Connects and locks the two foldable shafts.

Trimmer Head (Bump Head)

Stores the cutting line and releases the cutting line when the head is lightly tapped on the

ground during operation.

Guard

Reduces the risk of injury from foreign objects ung backwards toward the operator and from

contact with the cutting attachment.

Line-Cutting Blade

Steel blade on the guard that maintains the cutting line at the proper length.

SPECIFICATIONS

General

Rated voltage 20v d.c.

No-load speed

Low: 5000/min

High: 6000/min

Cutting mechanism Bump Head

Cutting line type 0.080 in. (2.0 mm) nylon twist line

Cutting width 13" (33 cm)

Recommended operating temperature 32–104°F (0–40°C)

Recommended storage temperature 32–104°F (0–40°C)

RECOMMENDED ACCESSORY

PART NAME TYPE MODEL NUMBER

Trimmer Head SKIL rapid reload trimmer head STH4818

Cutting Line 0.080 in./2.0 mm nylon twist line STL2000

11

ASSEMBLY

WARNING

To prevent accidental starting that could cause serious personal

injury, always remove the battery pack from the tool when assembling

parts, making adjustments, cleaning, or when not in use.

WARNING

If any parts are damaged or missing, do not operate this product until

the parts are replaced.

Use of this product with damaged or missing parts

could result in serious personal injury.

WARNING

Do not attempt to modify this tool or create accessories not

recommended for use with this tool.

Any such alteration or modication

is misuse and could result in a hazardous condition leading to possible serious injury.

Unpacking

•

This product requires assembly.

•

Carefully remove the product and any accessories from the box. Make sure that all items

listed on the box are included.

•

Inspect the tool carefully to make sure that no breakage or damage occurred during

shipping.

•

Do not discard the packing material until you have carefully inspected and satisfactorily

operated the tool.

•

If any parts are damaged or missing, please return the product to the place of purchase.

Tools needed for assembly/

maintenance

Screwdriver with PH2 Philips head

(not supplied)

Impact driver mounted with 14mm socket

(not supplied)

Unfold the Shaft

WARNING

In order to avoid pinching

your hands or fingers, do

not hold the shaft at the joints.

WARNING

Do not attempt to start

the trimmer until the shaft

has been locked.

1. Remove the battery pack from the trimmer.

2. Put your trimmer on the ground and care-

fully unfold the shaft. Make sure that the

cable is inside the shaft so that it will not be

pinched when closing the joints (Fig. 2).

3. Use a phillips head screwdriver (not sup-

plied) to lock the shaft with the two bolts

supplied (Fig. 3).

Fig. 2

Fig. 3

12

Mount the Guard

WARNING

Always wear gloves when mounting or replacing the guard.

Be careful

of the blade on the guard and wear gloves to protect your hands from

being injured by the blade.

1. Remove the battery pack from the trimmer.

2. Lay the trimmer on the ground or the oor with the trimmer head facing upward.

3. Insert the guard into the groove of the trimmer head.

4. Align the two bolts (supplied) with the two screw holes in the guard (Fig. 4), and then

tighten them with a phillips head screwdriver (not supplied) (Fig. 5).

Fig. 4

Fig. 5

Mount and Adjust the

Front-Assist Handle

1. Remove the battery pack from the trimmer.

2. Loosen the wing nut and remove it along

with the hex bolt from the front-assist

handle (Fig. 6).

Fig. 6

Front-Assist

Handle

Hex Bolt

Wing Nut

13

3. Press the front-assist handle onto the shaft

and assemble the hex bolt with the wing

nut. Turn the front-assist handle upward

so that it points toward the top of the rear

handle (Fig. 7).

4. Adjust the front-assist handle position so

that it is between the rear handle housing

and the hinge of the shaft, as shown in Fig.

8. The handle should be adjusted so that

your front arm is straight when using the

trimmer.

5. Tighten the wing nut so that the handle

cannot be rotated on the shaft.

Fig. 7

Fig. 8

14

OPERATING INSTRUCTIONS

WARNING

To reduce the risk of fire, personal injury, and product damage due to

a short circuit, never immerse your tool, battery pack, or charger in

fluid or allow a fluid to flow inside them.

Corrosive or conductive uids, such as seawater,

certain industrial chemicals, and bleach or bleach-containing products, etc. can cause a short

circuit.

WARNING

Do not use any attachments or accessories not recommended by the

manufacturer of this product.

The use of attachments or accessories not

recommended can result in serious personal injury.

WARNING

Do not attempt to modify this tool or the battery pack or create

accessories not recommended for use with this tool.

Any such

alteration or modication is misuse and could result in a hazardous condition leading to

possibly serious injury.

WARNING

To prevent accidental starting that could cause serious personal

injury, always remove the battery pack from the tool when assembling

parts, making adjustments, cleaning, or when not in use.

WARNING

Do not allow familiarity with this product to make you careless.

Remember that a careless fraction of a second is sufcient to inict serious

injury.

WARNING

Always wear eye protection with side shields marked to comply with

ANSI Z87.1, along with hearing protection. Failure to do so could

result in objects being thrown into your eyes and other possibly serious injuries.

This trimmer must be used only with the battery packs and charger listed below:

Battery Pack

Charger

2Ah 2.5Ah 4Ah 5Ah

SKIL BY519701

SKIL BY519702

SKIL

BY519703

SKIL

BY519601

SKIL

BY519603

SKIL SC535801

SKIL QC536001

SKIL SC5358B-02

NOTICE:

Please refer to the battery and charger manuals for detailed operating information.

Application

You may use this product for the purposes listed below:

Trimming:

use for removing grass and weeds along walls, fences, trees, and borders.

Cutting:

use for cutting grass that is difcult to reach using a normal mower.

15

To Attach/Detach Battery Pack

WARNING

Battery tools are always in operating condition. Therefore, remove

the battery when assembling parts, making adjustments, cleaning,

when the tool is not in use, or when carrying it at your side. Removing the battery pack

will prevent accidental starting that could cause serious personal injury

.

To Attach the Battery Pack (Fig. 9):

Align the raised rib on the battery pack with the grooves on the tool, and then slide the battery

pack onto the tool.

NOTICE:

Make sure that the latch on the battery pack snaps into place and that the battery

pack is secured to the tool before beginning operation.

NOTICE:

When placing the battery pack onto the tool, be sure that the raised rib on the

battery pack aligns with the groove inside the tool and that the latches snap into place

properly. Improper attachment of the battery pack can cause damage to internal components.

To Detach the Battery Pack (Fig. 10):

Depress the battery-release button, located on the front of the battery pack, to release the

battery pack. Pull the battery pack out and remove it from the tool.

Fig. 9

Fig. 10

Press to Release

To Hold the String Trimmer

WARNING

Dress properly to reduce

the risk of injury when

operating this tool. Do not wear loose

clothing or jewelry. Wear eye and ear/

hearing protection. Wear heavy, long pants,

boots and gloves.

Do not wear short pants or

sandals or go barefoot.

Before operating the unit, stand in the

operating position and check that:

1. The operator is wearing eye protection and

proper clothing.

2. One arm that is holding the rear handle is

slightly bent.

3. The other arm, that is holding the front-

assist handle, is straight.

4. The trimmer head is parallel to the ground and easily contacts the material to be cut

without the operator having to bend over (Fig. 11).

Fig. 11

16

To Start/Stop the String Trimmer

Before starting the string trimmer:

1. Make sure that you have a secure and balanced footing.

2. Stand upright and hold the string trimmer in a relaxed position.

3. Make sure that the cutting line is not touching the ground or any other objects.

4. Hold the string trimmer with both hands: one hand on the rear handle and one hand on the

front-assist handle.

To Start the String Trimmer (Fig. 12)

Press the lock-off button down and hold it in

that position. Press the trigger switch to turn on

the string trimmer. Release the lock-off button

and continue squeezing the trigger switch for

continued operation.

NOTICE:

The motor will only start when both

the lock-off button and the trigger switch are

depressed.

To Stop the String Trimmer

Release the trigger switch to stop the string

trimmer.

WARNING

Always remove the

battery pack from the

string trimmer during work breaks and after

finishing work.

Speed Selector (Fig. 13)

This string trimmer gives you the choice to

operate at a more efcient speed to extend

the runtime for larger jobs, or accelerate the

trimmer speed for high-performance cutting.

Push the speed selector forward or backward

to choose “HI” – high-speed, less energy-

efcient mode or “LO” – lower-speed, more

energy-efcient mode.

Fig. 12

Trigger Switch

Lock-off Button

Fig. 13

Speed Selector

17

To Use the String Trimmer

WARNING

To avoid serious personal injury, wear goggles or safety glasses at

all times when operating this unit. Wear a face mask or dust mask in

dusty locations.

WARNING

To prevent serious personal injury, remove the battery pack from the tool

before servicing, cleaning, changing attachments or removing material

from the unit.

WARNING

Clear the area to be cut before each use. Remove all objects, such as

rocks, broken glass, nails, wire, or string that can be thrown or become

entangled in the cutting attachment.

WARNING

Clear the area of children, bystanders, and pets. Keep all children,

bystanders and pets at least 100 ft. (30 m) away.

There still may be risk

to bystanders from thrown objects; bystanders should be encouraged to wear eye protection.

If you are approached, stop the motor immediately.

Check for Damaged/Worn Parts before Each Use.

Check the trimmer head, guard, and front-assist handle. Replace any parts that are cracked,

warped, bent, or damaged in any away.

The line-cutting blade on the edge of the guard can dull over time. It is recommended that you

periodically sharpen it with a le or replace it with a new blade.

WARNING

Always wear gloves when mounting or replacing the guard or when

sharpening or replacing the blade.

Note the location of the blade on the

guard and protect your hand from injury.

Clean the Trimmer after Each Use

See the Maintenance section for cleaning instructions.

WARNING

Never use water to clean your trimmer. Avoid using solvents when cleaning

plastic parts. Most plastics are susceptible to damage from various types

of commercial solvents. Use clean clothes to remove dirt, dust, oil, grease, etc.

Tips for Best Trimming Results

(Fig. 14)

1. The correct angle for the cutting attachment

is parallel to the ground.

2. Do not force the trimmer. Allow the very

tip of the line to do the cutting (especially

along walls). Cutting with more than the

tip will reduce cutting efciency and may

overload the motor.

3. The cutting height is determined by the

distance of the cutting line from the lawn

surface.

4. Grass should be cut by working

progressively from top to the bottom in

small increments to avoid premature line

wear or motor drag.

5. Slowly move the trimmer into and out of the area being cut, maintaining the cutting head

position at the desired cutting height. This movement can be either a forward-backward

motion or a side-to-side motion. Cutting shorter lengths produces best results.

6. Trim only when grass and weeds are dry.

Fig. 14

Danger Cutting Area

Best Cutting

Area

18

7. Wire and picket fences can cause extra string wear or breakage. Stone and brick walls,

curbs, and wood may wear strings rapidly.

8. Avoid trees and shrubs. Tree bark, wood moldings, siding, and fence posts can easily be

damaged by the strings.

To Adjust Cutting Line Length

The trimmer head allows the operator to

release more cutting line without stopping

the motor. As line becomes frayed or worn,

additional line can be released by lightly

tapping the trimmer head on the ground while

operating the trimmer (Fig. 15).

WARNING

Do not remove or alter the

line-cutting blade assembly.

Excessive line length will cause the motor to

overheat and may result in serious personal

injury.

For best results, tap the trimmer head on bare

ground or hard soil. If line release is attempted

in tall grass, the motor may overheat. Always

keep the trimming line fully extended. Line release becomes more difcult as the cutting line

becomes shorter.

Line Replacement

NOTICE:

Always use the recommended

nylon cutting line with a diameter that does

not exceed 0.080 in. (2.0 mm). Using line

other than that specied may cause the string

trimmer to overheat or become damaged.

WARNING

Never use metal

reinforced line, wire, or

rope, etc. These can break off and become

dangerous projectiles.

WARNING

To prevent serious

personal injury, remove

the battery pack from the tool before

servicing, cleaning, changing attachments

or removing material from the unit.

1. Remove the battery pack from the trimmer.

2. Cut one piece of cutting line less than 16

ft. (5m) long. Insert the line into the eyelet.

Push the line until the end of the line

comes out of the other side of the trimmer

head. Pull the line from the other side until

equal amounts of line appear on both sides

(Fig. 16).

3. Hold the lower cover and rotate the shroud

in the direction indicated by the arrow to

wind the cutting line into the trimmer head

until approximately 4.6 in. (12cm) of line is

showing on each side (Fig. 17).

Fig. 15

Fig. 17

Fig. 16

Arrow

Direction

Eyelet

4.6" (12cm)

Shroud

Lower

Cover

19

4. Push down on the trimmer head while pulling on the lines to manually advance the line

and to check for proper installation of the cutting line.

Reload the Cutting Line

NOTICE:

When the cutting line breaks from the line outlet or the cutting line is not released

when the trimmer head is tapped, you need to remove the remaining cutting line from the

spool retainer and follow the steps below to reload the line.

1. Remove the battery pack from the trimmer.

2. Press the release tabs on the upper cover and remove the lower cover of the trimmer

head by pulling it straight out (Fig. 18 and 19).

Fig. 18

Release Tab

Fig. 19

Lower CoverUpper Cover

3. Remove the cutting line from the spool

retainer.

4. With one hand holding the upper cover,

use the other hand to grasp the lower cover

of the trimmer head and align the tabs on

the upper cover with the holes in the lower

cover; use your palm to press the lower

cover until it snaps into place (Fig. 20).

5. Follow the instructions in “

Line

Replacement

” to reload the cutting line.

Fig. 20

Alignment

20

MAINTENANCE

WARNING

When servicing, use only identical replacement parts. Use of any

other parts could create a hazard or cause product damage.

Periodically inspect the entire product for damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product

until all missing or damaged parts are replaced. Please contact customer service or an

authorized service center for assistance.

WARNING

Battery tools do not have to plugged into an electrical outlet;

therefore, they are always in operating condition. To prevent serious

personal injury, take extra precautions and care when performing maintenance, service

or for changing the cutting attachment or other attachments.

WARNING

To avoid serious personal injury, always remove the battery pack

from the tool when cleaning or performing any maintenance.

Trimmer Head Replacement

DANGER

If the head loosens after it is fixed in position, replace it immediately.

Never use a trimmer with a loose cutting attachment. Replace a

cracked, damaged or worn out cutting head immediately, even if damage is limited to

superficial cracks.

Such attachments may shatter at high speed and cause

serious or fatal

injury.

Remove the Trimmer Head

1. Remove the battery pack from the trimmer.

2. Press the release tabs on the trimmer head and remove the lower cover of the trimmer

head by pulling it straight out.

3. Remove the cutting line from the trimmer head (Fig. 21).

4. Wear gloves. Use one hand to grasp the spool assembly to stabilize it and use the other

hand to hold an impact wrench with 14mm socket to loosen the nut in the counterclockwise

direction (Fig. 22).

Fig. 21

Fig. 22

Impact Wrench

La page charge ...

Skil LT4823B-10 Manuel utilisateur

Skil LT4823B-10 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents