Sanus VLT5 Manuel utilisateur

Taper
Manuel utilisateur
Scan for easy
install video
THANK YOU FOR CHOOSING SANUS
THE #1 TV MOUNT BRAND IN THE US.
MERCI D'AVOIR CHOISI SANUS
LE N ° 1 DE MARQUE TV de montage dans les États-Unis.
Balayez ce code pour
visionner une vidéo
d’installation facile
VLT
5
Instruction Manual
SANUS
MAGNETIC STUD FINDER
Designed to find your studs and make life easier – included in hardware kit.
TWO SIMPLE STEPS
TO FINDING YOUR STUDS:
Step 1 / Étape 1
Step 2 / Étape 2
WARNING:
This product contains a magnet. If an implanted medical device such as a pacemaker or implantable cardioverter defibrillator (ICD) is in use, magnetic fields may affect the operation of those devices, resulting in
serious injury or death. If you have an implanted medical device, keep at least 13 cm (5in.) between your device and the magnet. Please consult with your physician or medical professional prior to using this product.V
LOCALISATEUR DE MONTANTS
MAGNÉTIQUE
SANUS
Conçu pour trouver les montants et vous faciliter la vie. Inclus dans la trousse de quincaillerie.
magnet
locates screws in drywall
to show exactly where
your studs are
probing pin
helps find the edges of
your stud within the wall
level
attaches to your wall plate
for hands free leveling
aimant
localise les vis dans les cloisons
sèches pour indiquer l'emplace-
ment exact des montants
niveau
s'attache à votre plaque
murale pour une mise de
niveau mains libres
tige de sondage
vous aide à trouver les bords
des montants dans le mur
LOCALISEZ LES MONTANTS
EN DEUX SIMPLES ÉTAPES
:
Holding it vertically, lightly move the SANUS Magnetic Stud Finder up
and down while sliding across your wall. The magnet within will be
attracted to the screws in the stud.
Once the magnet has landed on a screw, place a pencil mark on the
wall directly below the magnet.
You can verify this is a stud by moving the Magnetic Stud Finder up or
down to find a second or third screw within the wall.
Placez le localisateur de montants magnétique SANUS en position verticale sur le
mur et faites-le glisser légèrement vers le haut et le bas. L'aimant situé à l'intérieur
sera attiré par les vis dans le montant.
Dès que l'aimant détecte une vis, marquez l'emplacement au crayon sur le mur,
directement sous l'aimant.
Vous pouvez vérifier que cela indique eectivement la présence d'un montant en
déplaçant le localisateur de montants magnétique vers le haut ou le bas pour
trouver une deuxième ou une troisième vis dans le mur.
Ouvrez le localisateur de montants magnétique SANUS pour exposer la tige de
sondage contenue à l'intérieur. Pour trouver les bords du montant, démarrez à
1/2 po (13 mm) de la première marque au crayon et insérez la tige de sondage
dans le mur tous les 1/8 po (3 mm) jusqu'à ce qu'elle rentre entièrement dans
le mur. Répétez cette opération jusqu'à ce que vous ayez localisé les deux
bords et le centre.
Pull apart the SANUS Magnetic Stud Finder to expose the probing pin
within. Starting about 1/2 inch away from the first pencil mark insert
the probing pin into the wall every 1/8 inch until it inserts completely
into the wall. Once that happens, you know you've found one edge of
your stud. Repeat this process till you have found the stud edges and
center of the stud.
AVERTISSEMENT :
Ce produit contient un aimant. Si un dispositif médical implanté comme un stimulateur cardiaque ou un défibrillateur cardioverteur implantable (DCI) est utilisé, le champ magnétique peut affecter le
fonctionnement de ces appareils et peut entraîner des blessures graves ou la mort. Si vous avez un dispositif médical implanté, conservez une distance de 13cm (5po) entre votre dispositif et l'aimant. Veuillez consulter votre médecin ou un
professionnel de la santé avant d'utiliser ce produit.
3
VLT5
We’ll Make It Stress-Free
If you have any questions along the way, just give us a call.
1-800-359-5520 (UK: 0800-056-2853) We’re ready to help!
Nous vous faciliterons la tâche, sans casse-tête
Si vous avez des questions en cours de route, appelez-nous.
Composez le 1-800-359-5520 (Royaume-Uni: 0800-056-2853)
Nous sommes là pour vous aider!
4
125 lb
(56.7 kg)
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
Before getting started, let’s make sure this mount is perfect for you!
No
Perfect!
Yes
This mount is NOT compatible. Visit MountFinder.Sanus.com or call
1-800-359-5520 (UK: 0800-056-2853) to nd a compatible mount.
Please read through these instructions completely to be sure you’re comfortable with this easy install process.
Also check your TV owner’s manual to see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use
of this product, contact Customer Service at 1-800-359-5520 (UK: 0800-056-2853).
Do you have
all the tools
needed?
1
2
3
4
What is your
wall made of?
Drywall
with steel
studs?
Unsure?
Drywall
with wood
studs?
Solid concrete
or concrete
block?
CAUTION: Avoid potential personal injuries and property damage!
This product includes directions and hardware for use with wood stud, solid concrete and concrete block walls
DO NOT install into drywall alone. For information on how to use this product with steel stud walls contact Customer
Service and ask about the SSMK1 steel stud mounting kit.
The wall must be capable of supporting fi ve times the weight of the TV and mount combined.
Do not use this product for any purpose not explicitly specifi ed by manufacturer.
Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
Call Customer Service: 1-800-359-5520 (UK: 0800-056-2853)
Perfect! Perfect!
Ready to
begin?
Steel stud kit (#SSMK1) required
7/32 in.
(5.5 mm)
Wood
Screwdriver Tape Measure Drill Bit Drill Bit Electric Drill Hammer Socket Wrench
3/8 in.
(10 mm)
Concrete
Does your TV weigh
more than 125 lb
(56.7 kg) including
accessories?
1/2 in.
(13 mm)
5
STEP 1 Attach Bracket to TV
NOTE: Not all hardware included will be used.
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged
item to your dealer; contact Customer Service. Never use damaged parts!
Parts and Hardware for STEP 1
Right TV
Bracket
Left TV
Bracket
02
x1
01
x1
Spacer
M4x35 mm
M5x35 mm
M6x35 mm
M8x35 mm
04
06
07
x4
x4
x4
03
05
08 09
x4 x4
x4
x4
TV Screws
TV Washers
Spacers
M8x45 mm
10
x4
6
1-1 Select TV Screws
Hand thread screws into the threaded inserts on the back of your TV
to determine which screw diameter (M4, M5, M6, or M8) to use.
1-2 Spacers
M4 M6 M8M5
Spacers and screws are supplied to install your TV bracket.
Determine your preference for spacer configuration when
attaching your TV bracket.
Mount the spacers
10
above the TV bracket,
so the TV bracket sits
close to the TV surface
for flat back panels.
TV Bracket
TV Bracket
Mount the spacers
10
under the TV bracket to
create extra space needed
for irregular shape TV
backs or large cables.
10
10
Round Back CablesInset HolesFlat Back
a
b
CAUTION: Verify adequate thread engagment of the screw/
spacer combination on your TV.
Too short will not hold the TV and too long will damage the TV.
Too Short Correct Too Long
7
IMPORTANT: For
ease of access, straps
should be level with
the bottom of the TV.
1-3 Attach TV Brackets
Center the TV brackets
01
and
02
over your TV hole pattern as shown - making sure the brackets are level.
NOTE: The tilt tension knob
T
on TV brackets
01
and
02
should be oriented to the outside edges.
Install using the spacer, screw and washer combination you selected for your TV.
a
Spacer, screw and washer
b
Spacer, screw and washer
10
10
08
08
09
09
03
03
04
04
05
05
06
06
07
07
0201
If your TV included inset spacers or wall mount adapters,
see Troubleshooting on PAGES 22-23.
T
Standard configurations are shown.
For special applications, or if you
are uncertain about your hardware
selection, contact Customer Service
at
1-800-359-5520
.
T
8
STEP 2 Attach Wall Plate to Wall
For wood stud installations, follow STEP 2A on PAGE 9
For concrete installations, follow STEP 2B on PAGE 14
* WARNING: This product contains a magnet. If an implanted medical device such as a pacemaker or implantable cardioverter defi brillator
(ICD) is in use, magnetic fi elds may a ect the operation of those devices, resulting in serious injury or death. If you have an implanted medical device,
keep at least 13 cm (5 in.) between your device and the magnet. Please consult with your physician or medical professional prior to using this product.
5⁄16 in. x 2 3⁄4 in.
* Sanus Magnetic Stud Finder
14
x4
11
x1
12
x1
13
x1
15
x4
Parts and Hardware for STEP 2
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged
item to your dealer; contact Customer Service. Never use damaged parts!
Wall Plate
Wall Plate
Template
Lag Bolt
Concrete Anchor
NOTE: Not all hardware included will be used.
9
STEP 2A Wood Stud Option
2
3
CAUTION: Avoid potential personal injuries and
property damage!
Drywall covering the wall must not exceed
5/8 in. (16 mm)
Minimum wood stud size: common 2 x 4 in.
(51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
Minimum horizontal space between fasteners:
16 in. (406 mm)
Stud centers must be verified – not all walls have
conventional 16 in. (406 mm) or 24 in. (610 mm)
stud spacing
1. Locate a nail/screw in the studs using the Sanus
magnetic stud finder
13
provided.
2. Find the edges of the studs using the probe
of the stud finder
13
.
3. Mark the centers of the studs with pencil.
13
1
Min. 16 in.
(406 mm)
Max. 5/8 in.
(16 mm)
Min. 3 1/2 in.
(89 mm)
Min. 1 1/2 in.
(38 mm)
10
4. Place the wall plate template
11
at your desired height and position the slotted holes over your stud center lines. Level the wall plate
template
11
and tape in place.
NOTE: For assistance in determining wall plate location, see HeightFinder at sanus.com.
IMPORTANT: Be sure you mark and drill into the center of the stud.
5. Drill the four pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 3 in. (75 mm).
1111
13
4 5
3 in. (75 mm)
7/32 in.
(5.5 mm)
11
6. Partially install the top two lag bolts
14
,
leaving about 1/2 in. (13 mm) space from the wall.
NOTE: This space allows you to remove the wall plate template
11
and hang the wall plate
12
onto the top lag bolts
14
.
7. Remove the wall plate template
11
.
1111
14
6 7
≈ 1/2 in.
(13 mm)
12
8. Slide the covers
C
open on the wall plate
12
to expose the mounting holes.
9. Hang the wall plate
12
on the top lag bolts
14
.
1412
C
C
12
8
9
13
10. Install the bottom two lag bolts
14
. Firmly tighten all four lag bolts
14
until they are pulled flush against the wall plate
12
.
NOTE: Hold the wall plate
12
in place when tightening the first lag bolt
14
to keep the plate from shifting out of place.
CAUTION: Avoid potential personal injury or property damage! All four lag bolts
14
MUST BE firmly tightened to prevent unwanted
movement of the wall plate
12
.
Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
11. Slide the covers
C
closed on wall plate
12
.
Go to STEP 3 on PAGE 18.
14
12
10
12
C
C
11
14
STEP 2B Solid Concrete or Concrete Block Option
CAUTION: Avoid potential personal injuries and property damage!
Mount the wall plate
12
directly onto the concrete surface
Minimum solid concrete thickness: 8 in. (203 mm)
Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)
Minimum horizontal space between fasteners: 24 in. (610 mm)
1. Position the wall plate template
11
on the wall at your desired height. Level the wall plate template and mark the hole locations.
NOTE: For assistance in determining wall plate location, see Height Finder at sanus.com.
2. Drill four pilot holes using a 3/8 in. (10 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 3 in. (75 mm). Never drill into the mortar between blocks.
11
11
13
1
2
3/8 in.
(10 mm)
3 in. (75 mm)
Min.
24 in.
(610 mm)
15
3. Remove the wall plate template
11
and insert four anchors
15
.
CAUTION: Be sure the anchors
15
are seated flush with the concrete surface.
4. Partially install the top two lag bolts
14
, leaving about 1/2 in. (13 mm) space from the wall.
NOTE: This space allows you to hang the wall plate
12
onto the top lag bolts
14
.
1415
11
3 4
≈ 1/2 in.
(13 mm)
16
5. Slide the covers
C
open on the wall plate
12
to expose the mounting holes.
6. Hang the wall plate
12
on the top lag bolts
14
.
141212
C
C
6
5
17
12
7. Install the bottom two lag bolts
14
. Firmly tighten all four lag bolts
14
until they are pulled flush against the wall plate
12
.
NOTE: Hold the wall plate
12
in place when tightening the first lag bolt
14
to keep the plate from shifting out of place.
CAUTION: Avoid potential personal injury or property damage! All four lag bolts
14
MUST BE firmly tightened to prevent unwanted
movement of the wall plate
12
.
Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
8. Slide the covers
C
closed on wall plate
12
.
14
7
12
C
C
8
18
HEAVY! You may need assistance with this step.
STEP 3 Attach TV to Wall Plate
1. Hook the TV brackets
01
and
02
onto the wall plate
12
.
NOTE: The TV brackets
01
and
02
can be slid anywhere along the wall plate
12
for optimal positioning of your TV.
2. Rest the TV into place against the wall.
3. Press the bottom of the TV into the wall plate
12
until the latches lock the TV in place.
CAUTION: Avoid potential personal injury or property damage! Always make sure your TV brackets are in the locked position so the
TV is securely fastened to the wall plate
12
.
01
02 12
12
0201
1 2 3
19
Manage Cables
Tilt the TV up or down to gain access to the back of the TV.
Attach your cables, then adjust the TV as desired.
Cables
20
Adjustments
LEVEL Tilt
To level your TV, turn the level
adjustment screw
S
on the top of
either TV bracket
01
or
02
to raise or
lower that respective side of the TV.
Your TV should adjust easily when moved,
then stay in place.
Adjust the tilt tension knob
T
if your TV
naturally tilts up or down.
NOTE: If you do not intend to adjust the
tilt for different viewing locations, you can
tighten the tilt tension knobs
T
to prevent
unwanted movement.
Raise
Lower
01
02
Tighten
Loosen
S
T
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Sanus VLT5 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues