Miele Complete C2 Limited Edition Review Le manuel du propriétaire

en Operating Instructions Vacuum Cleaner

fr Instructions d'utilisation Aspirateur

SFAE0

M.-Nr. 10 106 230

HS11

2

en-US ................................................................................................................. 5

fr-CA ................................................................................................................... 28

3

Only Miele FilterBags, filters and accessories with

the "Original Miele" logo can be used with this

vacuum. Only then can the suction power of the

vacuum cleaner reach its optimum potential creating

the best possible cleaning results.

USE OF NON-MIELE COMPONENTS MAY VOID

THE WARRANTY.

,

The use of FilterBags made of paper or a similar

material, or FilterBags with a cardboard retaining

plate can lead to serious damage to the vacuum

cleaner and may void the warranty, just as with the

use of FilterBags without the "Original Miele" logo.

The "Original Miele" Logo will appear on the

packaging or directly on the FilterBag.

Purchasing new FilterBags and filters

Original Miele FilterBags and filters can be purchased

from an authorized Miele vacuum dealer or by visiting the

Miele store at www.mieleusa.com.

en-US - Contents

4

IMPORTANT SAFETY INSTRUCTIONS................................................................. 5

Appliance description.......................................................................................... 10

Caring for the environment................................................................................. 12

References to illustrations .................................................................................. 13

Preparing for use ................................................................................................. 13

Using the accessories supplied ......................................................................... 15

Use ........................................................................................................................ 15

Parking, transport and storage........................................................................... 17

Maintenance......................................................................................................... 17

Purchasing new FilterBags and filters.................................................................... 17

Ordering the correct FilterBags and filters............................................................. 18

When to change the FilterBag .............................................................................. 18

How the FilterBag change indicator works............................................................ 18

Replacing the FilterBag ......................................................................................... 18

When to change the dust compartment filter ........................................................ 19

Changing the dust compartment filter .................................................................. 19

When to replace the exhaust filter? ....................................................................... 19

Replacing the AirClean exhaust filter .................................................................... 19

Replacing the Active AirClean 50 and HEPA AirClean 50 exhaust filters ............. 20

Replacing one type of exhaust filter with another.................................................. 20

When changing the filter, please note:................................................................... 20

When to change the thread catchers?................................................................... 20

Replacing the thread catchers .............................................................................. 20

Cleaning the roller on the floor brush AllTeQ ......................................................... 21

Cleaning and care................................................................................................ 21

Frequently asked questions................................................................................ 22

After sales service ............................................................................................... 23

Warranty conditions............................................................................................. 23

Optional accessories........................................................................................... 23

Limited Warranty - Vacuum Cleaners ................................................................ 25

en-US - IMPORTANT SAFETY INSTRUCTIONS

5

READ ALL INSTRUCTIONS BEFORE USING THIS AP‐

PLIANCE

This vacuum cleaner complies with current safety re‐

quirements. Inappropriate use can, however, lead to per‐

sonal injury and damage to property.

To avoid the risk of accidents and damage to the vac‐

uum cleaner, please read these instructions carefully be‐

fore using it for the first time. They contain important in‐

formation on its safety, operation and maintenance.

Keep these operating instructions in a safe place and

pass them on to any future user.

Always disconnect the vacuum cleaner from the power

supply when you have finished using it, before changing

over accessories, as well as for maintenance work and

cleaning. Turn the vacuum cleaner off and unplug it.

Correct use

 This vacuum cleaner is intended for cleaning flooring in

domestic households and similar residential environments.

 This vacuum cleaner can be used for all normal cleaning

of carpets, rugs and hard flooring.

 This vacuum cleaner is not intended for outdoor use.

 The vacuum cleaner must only be used to vacuum dry

floor surfaces. Do not use on people and animals. Any oth‐

er usage, modification or alteration is not supported by the

manufacturer and could be dangerous.

en-US - IMPORTANT SAFETY INSTRUCTIONS

6

 Persons which lack physical, sensory or mental abilities

or experience with the machine should not use it without

supervision or instruction by a responsible person.

Safety with children

 Children must be kept away from the vacuum cleaner

unless they are constantly supervised.

 Please supervise children in the vicinity of the vacuum

cleaner and do not let them play with it.

WARNING

To reduce the risk of fire, electric shock or injury:

 Check the voltage rating of the vacuum cleaner before

connecting the power cord to an electrical outlet. Your

power source should correspond with the voltage rating

plate located on the underside of the vacuum. Use only

household AC outlets. Never use DC power sources. If you

are not sure of your home’s voltage supply, consult a

qualified electrician. Connecting the vacuum cleaner to a

higher voltage than indicated in these instructions may re‐

sult in damage to the vacuum cleaner or injury.

 To reduce the risk of electric shock, this appliance has a

polarized plug (one blade is wider than the other.) This

plug will fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If it still

does not fit, contact a qualified electrician to install the

proper outlet. Do not alter the plug in any way.

en-US - IMPORTANT SAFETY INSTRUCTIONS

7

Technical safety

 Before using the vacuum cleaner and its accessories,

check for any visible signs of damage. Do not use a dam‐

aged appliance.

 Ensure that the connection data on the data plate of the

vacuum cleaner (voltage and frequency) match the house‐

hold electrical supply.

 The electrical outlet must be fitted with a 15 A fuse.

 Reliable and safe operation of this vacuum cleaner can

only be assured if it has been connected to the electricity

supply.

 While the vacuum cleaner is under warranty, repairs

should only be performed by a Miele-authorized service

technician. Otherwise the warranty will be void.

 Do not pull or carry the vacuum cleaner by the power

cord, and be careful not to damage the cord when with‐

drawing the plug from the socket. Keep the cord away

from sharp edges and do not let it get pinched, for exam‐

ple, under a door. Avoid running the vacuum cleaner over

the cord. This could damage the cord, plug or socket. The

appliance must not be used if any of these have suffered

damage.

 Do not use the vacuum cleaner if the cord is damaged.

If the cord is damaged it must be replaced together with a

complete cord reel. For safety reasons this work must be

done by Miele Service or a Miele-authorized service tech‐

nician.

en-US - IMPORTANT SAFETY INSTRUCTIONS

8

 When vacuuming fine dust, e.g., sawdust, sand, plaster,

flour, talcum powder, etc., electrostatic charges build up

naturally. Under certain conditions these charges will be

released. To avoid the unpleasant effects of these dis‐

charges, a metal inlay has been incorporated into the un‐

derside of the handle. Please make sure that you keep

your hand in constant contact with this metal strip during

vacuuming.

 Do not let the vacuum cleaner get wet. Clean only with a

dry cloth or slightly damp cloth when disconnected from

the mains supply.

 Repairs should only be carried out by a Miele-author‐

ized service technician. Repairs and other work by unqua‐

lified persons can cause considerable danger to users.

Proper use

 To avoid the risk of damage, do not use the vacuum

cleaner without the FilterBag, dust compartment filter and

exhaust filter in place.

 The dust compartment cover will not close without a Fil‐

terBag inserted. Do not force it.

 Do not vacuum up anything which has been burning or

is still glowing, e.g., cigarettes, ashes or hot ash, whether

glowing or apparently extinguished.

 Do not use the vacuum cleaner to vacuum up any water,

liquid or damp dirt. Wait until any freshly cleaned or sham‐

pooed rugs or carpets are completely dry before attempt‐

ing to vacuum.

en-US - IMPORTANT SAFETY INSTRUCTIONS

9

 Do not use the vacuum cleaner to vacuum toner dust.

Toner, such as that used in printers and photocopiers, can

conduct electricity.

 Do not vacuum up any inflammable or combustible liq‐

uids or gases and do not vacuum in areas where such

substances are stored.

 Floor attachments, accessories and wands must not be

used at head level.

Accessories

 To avoid the risk of injury when vacuuming with a Miele

turbobrush, do not touch the rotating roller brush.

 It is not advisable to vacuum directly with the handle,

i.e., without an accessory attached, as the rim could get

damaged and you could hurt yourself on sharp edges.

 Only use genuine FilterBags, filters and accessories with

the "Original Miele" logo on them. Otherwise the manufac‐

turer cannot guarantee the safety of the product.

SAVE THESE INSTRUCTIONS

en-US - Appliance description

10

The illustration shows the maximum number of features available

ONLY MIELE FILTERBAGS, FILTERS AND ACCESSORIES WITH THE "ORIGINAL

MIELE" LOGO CAN BE USED WITH THIS VACUUM CLEANER. USE OF NON-MIELE

COMPONENTS MAY VOID THE WARRANTY.

en-US - Appliance description

11

a

Handpiece

b

Air inlet valve

c

Release buttons

d

Telescopic wand

e

Telescopic wand release button

f

Hose connection socket

g

Release buttons for the dust compartment cover

h

Dust compartment filter

i

Original Miele FilterBag

j

Floor brush *

k

Carrying handle

l

Park system for storage (on both sides of the vacuum cleaner)

m

Exhaust filter *

n

Automatic cord rewind switch

o

Power cord

p

Suction power selector

q

Park system

r

On/Off foot switch 

s

Release button for accessories compartment

t

FilterBag change indicator

Features marked * depend on model and may vary or not be available on your

vacuum cleaner.

en-US - Caring for the environment

12

Disposal of packing material

The packaging is designed to protect

against transportation damage. The

packaging materials used are selected

from materials which are environmen‐

tally friendly for disposal and should be

recycled.

Recycling the packaging reduces the

use of raw materials in the manufactur‐

ing process and also reduces the

amount of waste in landfill sites.Make

sure the packaging is disposed of in the

proper manner for your area.

Disposing of the FilterBags

and filters

Filterbags and filters are made from en‐

vironmentally friendly materials, and

can be disposed of with the normal

household waste, as long as they have

been used exclusively for general

household dust.

Disposal of your old appliance

Before disposing of your old appliance

remove the FilterBag and filters and

dispose of them with your household

waste.

Old appliances may contain materials

that can be recycled. Please contact

your local recycling authority about the

possibility of recycling these materials.

You can obtain information on this mat‐

ter from your dealer, if necessary.

Please be sure that your old appliance

does not pose a danger to children

while being stored for disposal.

en-US

13

References to illustrations

The illustrations referred to in the text

are shown on the fold-out pages at

the end of these Operating Instruc‐

tions.

Preparing for use

Attaching the suction hose (Fig. 01)

 Insert the hose connector into the

suction socket on the vacuum clean‐

er until it clicks into position. To do

this, line up the guides on the two

pieces.

Disconnecting the suction hose

(Fig. 02)

 Press the release buttons at the side

of the hose connector, and lift the

hose from the socket.

Connecting the suction hose to the

handle (Fig. 03)

 Insert the suction hose into the han‐

dle until it clicks into position.

Connecting the handle to the wand

(Fig. 04)

 Insert the handle into the wand until it

clicks into position. To do this, line up

the guides on the two pieces.

 To release the handle from the wand,

press the release button and pull the

handle out of the wand, twisting it

slightly as you do so.

Adjusting the telescopic wand

(Fig. 05)

One part of the telescopic wand is

packed inside the other and can be ad‐

justed to suit your height for comforta‐

ble vacuum cleaning.

 Press the release button to release

the wands and adjust to the required

height.

Adjusting the standard floor brush

(Fig. 06)

 Push the wand into the floorbrush

and turn it clockwise or counter-

clockwise until it clicks into position.

 To detach the floor brush from the

suction wand, press the release but‐

ton.

en-US

14

Adjusting the floor brush AirTeQ

(Fig. 07, 08, + 09)

This vacuum cleaner can be used for all

normal cleaning of carpets, rugs and

hard flooring.

Miele offer a range of other floor tools,

brushes and accessories for other

types of flooring and special require‐

ments

(see "Optional accessories").

Please observe the flooring manu‐

facturer's cleaning and care instruc‐

tions.

Vacuum carpets and rugs with the

brush retracted:

 Press the foot switch .

Clean hard flooring which is not sus‐

ceptible to scratching, as well as floor‐

ing with gaps or deep crevices in it with

the brush protruding:

 Press the foot switch .

Floor brush AirTeQ (Fig. 09)

If the suction power of the floor

brush AirTeQ seems too high, reduce

the suction until the floor brush is

easier to maneuver (see "Use - Reg‐

ulating the suction power").

Activating the exhaust filter change

indicator

Depending on the model, your vacuum

cleaner will be fitted as standard with

one of the following exhaust filters (Fig.

10):

a AirClean

b Active AirClean 50 (black)

c HEPA AirClean 50 (white)

If your vacuum cleaner is fitted with fil‐

ter b or c, you need to activate the ex‐

haust filter change indicator.

 Lift the release button for the dust

compartment lid and raise the lid until

it engages (Fig. 11).

 Remove the indicator strips (Fig. 12).

 Press the exhaust filter change indi‐

cator (Fig. 13).

After approx. 10 - 15 seconds, a thin

red stripe will appear in the left hand

side of the display (Fig. 14).

 Close the dust compartment lid se‐

curely, making sure it clicks into posi‐

tion. Take care not to trap the Filter‐

Bag when doing so.

Function of the exhaust filter change

indicator

The exhaust filter change indicator

shows the remaining functional life of

the exhaust filter. After approx. 50 oper‐

ating hours, or approx. one year of

average use, the display will be com‐

pletely filled with red (Fig. 15).

en-US

15

Using the accessories sup‐

plied (Fig. 16)



Crevice nozzle



Dusting brush



Upholstery nozzle

Opening the accessories compart‐

ment (Fig. 17)

 Press the release button on the ac‐

cessories compartment lid.

The accessories compartment will then

open.

 Take out the accessory you require.

 Press down firmly on the lid to close

it.

Floor brush (Fig. 18)

For general use and also for vacuuming

the stairs.

 For safety reasons when vac‐

uuming stairs, it is best to start at the

bottom of the stairs and move up‐

wards.

Use

Power cord

 Unwind the cord completely to

aid the vacuum in dissipating heat.

Do not pull or carry by the cord, use

the cord as a handle, close a door

on the cord, or pull the cord around

sharp edges or corners. Do not run

the appliance over the cord. Keep

the cord away from heated surfaces.

Do not unplug by pulling the cord. To

unplug grasp the plug, not the cord.

This appliance is equipped with a

power cord reel. Hold the plug when

rewinding onto cord reel. Do not al‐

low plug to whip when rewinding.

Unwind the power cord (Fig. 19)

 Pull the power cord out to the re‐

quired length (max. cable length ap‐

prox. 21' (6.5 m)).

 Insert the plug into the electrical out‐

let.

 If vacuuming for longer than 30

minutes, the power cord must be

pulled out all the way Otherwise

there is a danger of overheating and

damage.

Rewinding the power cord (Fig. 20)

 Turn off at the wall socket and un‐

plug.

 Press the rewind foot control. The

cord will rewind automatically.

Turning the vacuum cleaner on and

off (Fig. 21)

 Press the On/Off foot control .

en-US

16

Regulating the suction power

(Fig. 22)

The suction power can be regulated to

suit the type of flooring being cleaned.

Reducing the suction power reduces

the amount of effort required to maneu‐

ver the floor brush.

The vacuum cleaner has symbols on

the controls which indicate the type of

use the settings are suitable for.



Curtains, fabric



Upholstery, cushions



Deep pile carpets, rugs and run‐

ners



Energy-saving vacuuming. This

setting is also very quiet



Low pile carpet and rugs



Hard flooring and heavily soiled

carpets and rugs

When using the AirTeQ floor brush, if

the suction seems too high, reduce

the suction until the floor brush is

easier to maneuver.

 Turn the suction power selector man‐

ually to the suction power setting you

require.

Opening the air inlet valve (Fig. 23)

It is easy to reduce the suction power

for a short time, e.g., to prevent rugs or

other objects being sucked into the

vacuum cleaner.

 Open the air inlet valve on the handle

far enough to reduce the suction

power.

This reduces the suction on the respec‐

tive nozzle used.

During vacuuming

 When vacuuming, pull the vacuum

cleaner behind you on its wheels. You

can stand it upright for vacuuming

stairs and curtains, etc.

 When vacuuming fine dust, e.g.,

sawdust, sand, plaster, flour, talcum

powder, etc., electrostatic charges

build up naturally. Under certain con‐

ditions these charges will be re‐

leased. To avoid the unpleasant ef‐

fects of these discharges, a metal in‐

lay has been incorporated into the

underside of the handle. Please

make sure that you keep your hand

in constant contact with this metal

strip during vacuuming. (Fig. 24)

en-US

17

Parking, transport and storage

Park system for pauses during vac‐

uuming (Fig. 25)

The park system allows you to conven‐

iently park the suction wand and floor

brush during pauses.

 Slot the floor brush into the parking

attachment at the back of the vac‐

uum cleaner.

If your vacuum cleaner is on a slop‐

ing surface, e.g., a ramp, retract the

telescopic wand fully.

Park system for storage (Fig. 26)

 Always unplug the vacuum

cleaner from the electrical supply

when you have finished using it.

 Stand the vacuum cleaner upright.

Retract the telescopic wand fully so

that the vacuum cleaner takes up less

room for storage.

 Insert the floor brush downwards into

one of the slots on the sides of the

vacuum cleaner.

This makes the vacuum cleaner easier

to carry or store.

Maintenance

 Always disconnect the vacuum

cleaner from the electrical supply for

maintenance work. Unplug it from

the wall socket.

The Miele filtration system consists of

three filters:

– FilterBag

– Dust compartment filter

– Exhaust filter

These will need to be replaced from

time to time to ensure that your vacuum

cleaner performs efficiently.

Only use genuine FilterBags, filters

and accessories with the "Original

Miele" logo on them. This will ensure

that the suction power of the vac‐

uum cleaner is maintained, giving the

best possible cleaning results.

 The use of dustbags made from

paper or paper-based materials, or

dustbags with a cardboard collar, or

dustbags that do not carry the "Orig‐

inal Miele" logo, can seriously dam‐

age the vacuum cleaner and invalid‐

ate the warranty.

Purchasing new FilterBags and filters

Original Miele FilterBags and filters can

be ordered from Miele, your Miele deal‐

er or online at:

en-US

18

Ordering the correct FilterBags and

filters

Only use original Miele G/N FilterBags

with a blue collar and original Miele fil‐

ters. These are identified by the "Origi‐

nal Miele" logo on the packaging or di‐

rectly on the FilterBag.

An AirClean filter and a dust compart‐

ment filter are supplied with every

packet of Miele FilterBags.

These can also be purchased separate‐

ly from your Miele Dealer, from Miele or

from the online shop. Please quote the

model number of your vacuum cleaner

when ordering to make sure you get the

correct filter.

When to change the FilterBag

(Fig. 27)

Change the FilterBag when the color

marker in the FilterBag change indicator

turns red, or sooner if it is no longer ef‐

fective (see possible reasons for this

below).

Miele FilterBags are disposable and

designed for single use only. Dis‐

pose of the FilterBag when full. Do

not attempt to reuse. Blocked pores

in used FilterBags will reduce the

suction power of the vacuum clean‐

er.

Checking the FilterBag change indi‐

cator

 Attach the standard floor brush to the

wand.

 Turn the vacuum cleaner on using the

On/Off foot switch  and set the

suction power selector to the highest

power setting.

 Lift the floor brush off the floor a little.

How the FilterBag change indicator

works

The FilterBag change indicator is set for

normal household dust. This generally

contains a mixture of dust, hair,

threads, carpet lint, grit, etc.

However, if the cleaner has been used

to vacuum up fine dust, such as plaster,

brick dust, cement or flour, the pores of

the FilterBag will become blocked very

quickly.

This affects the air permeability of the

bag, and the marker will indicate that

the bag is "full" even when it is not. If

this happens you must still change the

FilterBag because suction power will be

greatly reduced by blocked pores in the

FilterBag.

If, on the other hand, a large amount of

hair and carpet lint which typically con‐

tains a lot of air is vacuumed up, the in‐

dicator may fail to react even though

the bag is full. You should still change

it. Both these extremes can occur.

Replacing the FilterBag (Fig. 28 + 29)

 Lift the release button for the dust

compartment lid and raise the lid until

it engages (Fig. 11).

en-US

19

The FilterBag has a closing flap which

closes automatically when the dust

compartment lid is raised to prevent

any dust escaping.

 Pull the FilterBag out by the grip on

the collar.

 Insert the new FilterBag into the hold‐

er as far as it will go. Leave it folded

up when you take it out of the box.

 It should be unfolded as far as possi‐

ble in the dust compartment.

 Close the dust compartment lid se‐

curely, making sure it clicks into posi‐

tion. Take care not to trap the Filter‐

Bag when doing so.

An empty operation lock prevents

the FilterBag from closing without a

FilterBag in place. Do not force it!

When to change the dust compart‐

ment filter

Replace this filter every time you start a

new packet of FilterBags. A dust com‐

partment filter is supplied with every

packet of Miele FilterBags.

Changing the dust compartment fil‐

ter (Fig. 30)

 Open the dust compartment lid

 Pull the FilterBag out by the grip on

the collar.

 Lift up the filter frame until it clicks

and remove the old filter. Hold by the

clean, unsoiled section to remove it.

 Replace with a new dust compart‐

ment filter (for motor protection).

 Close the filter frame.

 Insert the FilterBag into the holder as

far as it will go.

 Close the dust compartment lid se‐

curely, making sure it clicks into posi‐

tion. Take care not to trap the Filter‐

Bag when doing so.

When to replace the exhaust filter?

Depending on the model, your vacuum

cleaner will be fitted as standard with

one of the following exhaust filters (Fig.

10):

a AirClean

Replace this filter every time you start a

new packet of Miele FilterBags. An Air‐

Clean exhaust filter is supplied with ev‐

ery packet of Miele FilterBags.

b Active AirClean 50 (black)

c HEPA AirClean 50 (white)

Replace if the display for the exhaust

filter change indicator is completely fil‐

led with red (Fig. 15). This occurs after

approx. 50 hours of operation which is

equivalent to about a year of average

use. The vacuum cleaner can still be

used. However, the suction power will

be reduced as will the effectiveness of

the filter if it is not replaced in good

time.

Replacing the AirClean exhaust filter

(Fig. 31 + 32)

Do not use more than one exhaust fil‐

ter at a time.

 Open the dust compartment lid.

 Release the filter frame and raise it

upwards. Grasp the used exhaust fil‐

ter by the clean, unsoiled section (see

arrow) and take it out.

en-US

20

 Replace it with a new AirClean ex‐

haust filter.

If you wish to fit an Active AirClean

50 or HEPA AirClean 50 exhaust fil‐

ter, see "Replacing one type of ex‐

haust filter with another."

 Close the filter frame.

 Close the dust compartment lid.

Replacing the Active AirClean 50 and

HEPA AirClean 50 exhaust filters

(Fig. 33 + 34)

Do not use more than one exhaust fil‐

ter at a time.

 Open the dust compartment lid.

 Lift the exhaust filter and remove it.

 Insert a new exhaust filter making it

sure it goes in properly, then push it

down into position.

 Press the exhaust filter change indi‐

cator (Fig. 13).

After approx. 10 - 15 seconds, a thin

red stripe will appear in the left hand

side of the display (Fig. 14).

If you wish to insert an AirClean ex‐

haust filter, see "Replacing one type

of exhaust filter with another".

 Close the dust compartment lid.

Replacing one type of exhaust filter

with another

Depending on the model, your vacuum

cleaner will be fitted as standard with

one of the following exhaust filters (Fig.

10):

a AirClean

b Active AirClean 50 (black)

c HEPA AirClean 50 (white)

Do not use more than one exhaust fil‐

ter at a time.

When changing the filter, please

note:

1. If you wish to replace exhaust filter a

with filter b or c, it is essential that

you remove the filter frame before

you fit the new exhaust filter.

In addition, you must activate the ex‐

haust filter change indicator (Fig. 13).

2. If you wish to replace exhaust filter b

or c instead of a, so it is essential

that you also fit it in a filter frame *

(Fig. 32).

* Filter frame - see "Optional acces‐

sories."

When to change the thread catch‐

ers?

The thread catchers on the suction inlet

to the floor brush can be replaced.

Check them from time to time and re‐

place them if the pile has worn down.

Replacing the thread catchers

(Fig. 35 + 36)

 Use a suitable screwdriver to remove

the thread lifters from the slots.

La page charge ...

Miele Complete C2 Limited Edition Review Le manuel du propriétaire

Ce manuel convient également à

Miele Complete C2 Limited Edition Review Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents