JennAir JBBFL36NHS Guide d'installation

GETTING STARTED | 1

GETTING STARTED

BUILT-IN REFRIGERATOR FULL HEIGHT DOOR PANEL KIT

INSTALLATION INSTRUCTIONS

TROUSSE DE PORTE PLEINE GRANDEUR POUR

RÉFRIGÉRATEUR ENCASTRÉ

INSTRUCTIONS D’INSTALLATION

W11172224C

2 | GETTING STARTED

BUILT-IN REFRIGERATOR FULL HEIGHT DOOR PANEL KIT

GETTING STARTED | 3

GETTING STARTED

INTRODUCTION

TABLE OF CONTENTS

INTRODUCTION

SAFETY

You can be killed or seriously injured if

you don't immediately follow instructions.

You can be killed or seriously injured if

you don't immediately follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,

and tell you what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and

obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER”

or WARNING.”

These words mean:

DANGER

WARNING

INTRODUCTION

Safety ............................................................ 3

Registering Your Product .............................. 4

Product Identication .................................... 4

SITE PREPARATION

Before Installation .......................................... 5

Tools and Parts Required .............................. 5

Tools and Parts Provided .............................. 5

Parts Supplied with Refrigerator ................... 6

Installation Requirements .............................. 7

Plan the Installation ....................................... 7

Opening Requirements .................................. 7

Cabinet and Panel Installation Options ......... 7

Cabinet Cutout Options ................................ 8

Airow and Venting Recommendations ........ 8

Panel Dimensions .......................................... 9

Secondary Anti-Tip Board ............................. 10

INSTALLATION

Installing Grille Bracket Assembly ................. 11

Installing Air Divider ....................................... 12

Installing Grille Panel ..................................... 13

Removing Film from Panels .......................... 14

Installing Freezer Panel ................................. 15

Installing Door Panel(s) .................................. 16

Moving Refrigerator to Final Position ............ 18

Adjusting Door Swing .................................... 19

Adjusting Freezer Panel ................................. 20

Adjusting Refrigerator Panel(s) ...................... 21

Attaching Panel(s) .......................................... 23

Completing the Installation ............................ 25

TABLE DES MATIÈRES.................27

INTRODUCTION | 3

4 | INTRODUCTION

INTRODUCTION

REGISTRATION

REGISTERING YOUR

PRODUCT

Gain access to our concierge-level Customer Support

by registering your appliance. We make product

registration simple and straightforward so that you

can start using your exclusive JennAir benets today.

Registering your appliance allows you to:

 Streamline your warranty service

If we have your product information, we

can help you faster.

 Protect your purchase

In case of an insurance loss, such as re,

ood, or theft, your product registration

could serve as a proof of purchase.

 Keep your family safe

We’ll notify you in the rare case of a safety

notication.

Start taking advantage of these benets today by

going on-line to register your product at

jennair.com/customer-care. In Canada, register

your product at jennair.ca.

PRODUCT IDENTIFICATION

Your product identication, which includes the model

and serial numbers, is listed on the product rating

plate.

Recording this information below allows us to more

easily assist you if your product should ever require

service from one of our JennAir Authorized Service

Providers.

Model Number: ________________________________

Serial Number: ________________________________

Date of Installation: ___________________________

Authorized Dealer: ____________________________

Authorized Dealer Phone #: ____________________

SITE PREPARATION | 5

SITE PREPARATION

BEFORE INSTALLATION

IMPORTANT:

 These instructions are intended as a

general guide only and do not supersede

any national or local codes in any way.

Compliance with all local, state, or national

codes pertaining to this type of installation

should be determined prior to installation.

 These instructions are intended to

supplement the Installation Instructions

provided with your refrigerator, not replace

them. Follow the instructions provided with

the refrigerator to install it into the cabinet.

NOTE: The hardware bag contains all

the parts and fasteners needed to install

panels. Most of these components have

been pre-installed on the panels included in

this kit. A hardware bag is shipped with the

refrigerator. You will nd the hardware bag in

either one of the crisper drawers or attached

to the outside of one of the refrigerator

doors.

Pinch Hazard

Installation of door panels with less than a ³⁄₈"

(0.95 cm) gap between the door panel and the

adjacent cabinet increases the risk of potential

pinching.

CAUTION

TOOLS AND PARTS REQUIRED

Assemble the required tools and parts before starting

installation. Read and follow the instructions provided

with any of the required tools listed here. Proper

installation is your responsibility.

Tools Required:

 Cordless drill and drill bits

 3/8" and 1/2" Open-end wrenches or two

adjustable wrenches

 Phillips screwdriver

 Small level

 Appliance dolly

 3/32", 5/32", and 3/16" Hex keys

 1/4" and 5/16" Nut drivers

 6" Extension nut drivers

 Tape measure

TOOLS AND PARTS PROVIDED

Parts Supplied with Panel Kit:

 Exterior door panels with handles and

mounting hardware pre-installed.

 Instructions

Grille Panel Grille bracket assembly

Foam air divider

Parts Supplied with Refrigerator

(Needed to Install Panel Kit):

Phillips-head at screw

Black: 8281252

Slotted hex-head screw

W10141645

Door stop pin

W10234202

6 | SITE PREPARATION

PARTS SUPPLIED WITH

REFRIGERATOR

The following parts are either not needed to install

the panels in this kit, or they are already installed on

the panels. These parts can be discarded after the

installation is completed:

Panel top bracket

Black: W10667450

“L” brackets

W10234199

Standard grille bracket

W10182743 (left)

W10172741 (right)

Integrated grille bracket

W10260890 (left)

W10260891 (right)

Hex-head pointed screw

W10141189

Hex-head blunt screw

W10142233

Round-head screw

1163283

Shoulder washer

W10471946

Freezer panel brackets

W10606815

SITE PREPARATION

BEFORE INSTALLATION (CONTD.)

SITE PREPARATION | 7

SITE PREPARATION

INSTALLATION REQUIREMENTS

PLAN THE INSTALLATION

IMPORTANT:

Plan your installation using these instructions in

conjunction with the Installation Instructions provided

with the refrigerator. Modications must be made to

the refrigerator to accommodate the full height door

panels.

Required parts

 One of the following built-in refrigerator

models:

42" Side-by-Side: JS42NXFXDE

48" Side-by-Side: JS48NXFXDE

36" Bottom Mount: JB36NXFXLE,

JB36NXFXRE

36" French Door Bottom Mount:

JF36NXFXDE

42" French Door Bottom Mount:

JF42NXFXDE

 Steel Panels with handles and Accessory

Full Height Door Panel Kit (which includes

Grille Panel and Grille Bracket Assembly).

OPENING REQUIREMENTS

IMPORTANT:

 The width of the opening, from side to side,

must be as specied for your model, for

at least 3" (7.62 cm) back from the face of

the cabinet. If your opening does not meet

this requirement, you will need to make

modications.

 The depth of the opening from the front

of the cabinet to the back wall must be

25" (63.5 cm) minimum to achieve a ush

installation.

CABINET AND PANEL INSTALLATION

OPTIONS

Cabinet Depth - 25" (63.5 cm)

Grille Bracket - Top View

Grille Bracket - Side View

AB E

C

D

C

B

A

A. Refrigerator door

B.

Full height door panel

C. Side trim

D. Grille bracket

E. Adjacent cabinet

A. Refrigerator door

B.

Full height door panel

C. Side trim

D. Grille bracket

8 | SITE PREPARATION

SITE PREPARATION

CABINET CUTOUT OPTIONS

AIRFLOW VENTING RECOMMENDATIONS

IMPORTANT:

 Full height door style installations recommends a minimum of 1/8" (3.2 mm) of open space above the refrigerator. It is recommended that this space not be blocked in

any way, including softs.

 Models may be installed using either Option 1, Option 2 or option 3.

Option 1 - Open to Ceiling

Option 2 - False Front (cabinet face only) Option 3 - Closed Soft

Open to ceiling

False front

1/8" (3.2 mm) gap

SITE PREPARATION | 9

SITE PREPARATION

BOTTOM MOUNT MODEL

A

B

C

Legend Model Dimension

A 36" 35

3

/

4

" (90.61 cm)

B 36" 59

1

/

8

" (150.2 cm)

C 36" 20

1

/

2

" (52.07 cm)

FRENCH DOOR BOTTOM MOUNT

MODELS

A A

D

B

C

Legend Model Dimension

A

36"

17

3

/

4

" (45.09 cm)

B 59

1

/

8

"(150.2 cm)

C 20

1

/

2

" (52.07 cm)

D 35

3

/

4

" (90.61 cm)

A

42"

20

3

/

4

" (52.71 cm)

B 59

1

/

8

" (150.2 cm)

C 20

1

/

2

" (52.07 cm)

D 41

3

/

4

" (105.85 cm)

SIDE BY SIDE MODELS

A B

C

Legend Model Dimension

A

42"

17

3

/

4

"(45.14 cm)

B 23

3

/

4

" (60.38 cm)

C 81" (205.7 cm)

A

48"

20

1

/

4

" (51.49 cm)

B 27

1

/

4

" (69.27 cm)

C 81" (205.7 cm)

SITE PREPARATION

PANEL DIMENSIONS

Maximum possible panel weight: 46 lbs (20.9 kg)! Maximum possible panel weight: 34 lbs (15.5 kg)! Maximum possible panel weight: 48 lbs (21.7 kg)!

10 | SITE PREPARATION

IMPORTANT:

 For all full height door panel installations, the

secondary anti-tip board is required to be

installed prior to door panel installation.

 This anti-tip board is to be secured on the

right side of the cabinet enclosure as per the

dimensions shown in illustration.

NOTE: Anti-tip board is required as an

addition to the rear wall anti-tip board (for

open to ceiling installation) described in the

installation instructions provided with the

refrigerator.

 Secure the secondary anti-tip board so that

the bottom surface of the secondary anti-tip

board is 75

1

/

2

" (191.77 cm) from the oor

(right hand side).

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily

when not completely installed.

Install secondary anti-tip board to ensure

product stability.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or

serious injury.

INSTALLING THE SECONDARY ANTI-

TIP BOARD

1. Mark the stud locations on right hand side

cabinet wall.

2. Securely attach one 2" x 4" x 12" (5 cm x 10 cm

x 30.4 cm) board to the cabinet on right hand

side cabinet using wood screws. Use three

#8 x 2" (5.08 cm) (or longer) wood screws.

NOTE:

 It is recommended to drive the wood screws

from cabinet wall into the secondary anti-tip

board as shown in the illustration.

 The board must have overlap of 1" (2.54)

with the refrigerator top.

 Leave 4" (10.16 cm) free space at rear as

shown in the illustration.

A

B

D

C

75

1

/

2

"

(191.77 cm)

A. Refrigerator

B. Secondary anti-tip board

C. Kitchen cabinet

D. Wood screws

4" (10.16 cm)

SITE PREPARATION

SECONDARY ANTI-TIP BOARD

 The main anti-tip boards for open to ceiling

installation are secured at 84" (213.36 cm)

from the oor (rear side).

 During panel installation, raise the

refrigerator up until the top of the refrigerator

is making contact with the bottom of the

secondary anti-tip board.

INSTALLATION | 11

INSTALLATION

INSTALLING GRILLE BRACKET ASSEMBLY

APPLIES TO:

NOTE: If refrigerator is not on rollers, it is

recommended to lower the product to have more

access at the top of product for panel installation. For

ease of grille installation, it is recommended to have

product outside of kitchen cabinet not more than 8"

(20.32 cm).

1. Remove the three screws fastening each

mounting plate to the top of the refrigerator on

each side. Discard the mounting plates but keep

the screws for attaching the two grille bracket

assemblies provided in this kit.

2. Remove the two screws fastening the air divider

to the unit housing. Discard the air divider, and

reinstall the screws into the holes from where

they were removed.

3. Align the three holes in a grille bracket assembly

with the three holes in a cabinet side, as shown.

Using the screws removed in Step 1, attach the

grille bracket assembly.

4. Repeat step 3 to install the other grille bracket

assembly to the opposite side of the refrigerator.

IMPORTANT: Installing the full height door

panels before removing both existing factory

installed grille brackets can damage the panels.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other

injury.

2

3

1

Parts to be used:

X2 Grille bracket assembly

12 | INSTALLATION

INSTALLATION

INSTALLING AIR DIVIDER

APPLIES TO:

1. Peel away the paper layer from the foam air

divider to reveal the adhesive side.

2. Stick the foam air divider to unit housing at the

location where metallic air divider was installed

earlier by applying even pressure.

ON

OFF

2

1

Align the base of foam air divider with base of unit housing!

Parts to be used:

X1 Foam air divider

INSTALLATION | 13

INSTALLATION

APPLIES TO:

1. Position the grille panel between the grille

brackets on each side of the cabinet.

2. Hook the top of grille onto the upper rivet pins.

Rotate downward and push the bottom of the

grille panel in until the grille panel snaps into

place.

NOTE: For grille panel removal, push the top of grille

panel inward until the lower portion snaps out. Rotate

and lift off the grille panel.

INSTALLATION

INSTALLING GRILLE PANEL

1

2

Parts to be used:

X1 Grille panel

14 | INSTALLATION

APPLIES TO:

1. Peel off the ﬁlm covering on all the door / drawer

panels completely.

NOTE: Gently handle the panels after ﬁlm is

removed to avoid the panels from external

damages such as scratches.

INSTALLATION

REMOVING FILM FROM PANELS

1

INSTALLATION | 15

INSTALLATION

INSTALLING FREEZER PANEL

APPLIES TO:

1. Slightly loosen the bracket screws present on

freezer panel.

NOTE: Be sure that the refrigerator door(s) are

tightly closed.

2. Slide panel onto drawer. Retighten the four

screws on each side attaching the bracket to the

drawer panel.

3. Using the Phillips-head ﬂat screws, fasten the

panel brackets to the drawer.

4. To allow for later adjustment of the panel, do not

fully tighten the screws attaching the bracket to

the drawer.

IMPORTANT: When you have completed

installing all the panels, check for alignment.

The drawer panel will move up or down to align.

Completely tighten the screws only when panels

are fully aligned.

2

3

1

FOR SIDE BY SIDE MODELS - SKIP THIS STEP!

4

Parts to be used:

X6 Phillips-head screws

16 | INSTALLATION

APPLIES TO:

NOTE:

 Be sure that secondary anti-tip board is installed

before opening the door. Refer “INSTALLING

THE SECONDARY ANTI-TIP BOARD” section to

install the secondary anti-tip board.

 For panel installation, it is recommended to have

product outside of kitchen cabinet not more than

8" (20.32 cm).

 Raise the refrigerator until the top of the

refrigerator touches the bottom of secondary

anti-tip board.

 Open only one door at a time.

1. Open the door(s) and remove the hinge cover(s).

NOTE: French door and bottom mount models

have bottom hinge cover(s) that also must be

removed.

2. Take out the door adjustment pin cover(s) to

expose the adjustment pins.

3. Use foam packaging to prop and hold the door

open while installing a door panel.

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily

when not completely installed.

Install secondary anti-tip board to ensure

product stability.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or

serious injury.

INSTALLATION

INSTALLING DOOR PANEL(S)

2

1

3

INSTALLATION | 17

INSTALLATION

INSTALLING DOOR PANEL(S) (CONTD.)

4. Align the two shoulder washers, on the back of

the door panel, with the “J” slots on the side of

the refrigerator door.

5. Simultaneously slide the panel onto the door,

and lower the panel bracket down onto the

adjustment pins at the top of the door.

NOTE:

 On French door and side by side models, repeat

steps 2 through 5 to install the second door

panel.

 After panel(s) are installed properly, lower the

refrigerator onto the rollers.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

panels.

Failure to do so can result in back or other

injury.

4

5

18 | INSTALLATION

INSTALLATION

MOVING REFRIGERATOR TO FINAL POSITION

APPLIES TO:

1. Gently push back the refrigerator into the cabinet

so that all the panels ﬂush with adjacent cabinets

from all sides.

2. Use a 5/16" Nut driver to turn the leveling bolts

clockwise to raise the refrigerator. Adjust the

leveling bolts until the top of the refrigerator is

making contact with the bottom of the secondary

anti-tip board.

IMPORTANT: After height adjustment, ensure

refrigerator is perfectly leveled horizontally. And

ensure panels are ﬂush with adjacent cabinets.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other

injury.

A

B

A. Leveler

A. Rear leveling bolt B. Front leveling bolt

2

1

INSTALLATION | 19

INSTALLATION

APPLIES TO:

1. If the standard 110° door swing is too wide,

install the door stop pin to allow for a maximum

90° door swing. Insert the door stop pin into the

top hinge in the hole shown. Use a 5/32" hex

key, to tighten door stop pin.

INSTALLATION

ADJUSTING DOOR SWING

1

Parts to be used:

Door stop pin (as required)

20 | INSTALLATION

APPLIES TO:

1. A 1/8" (3.2 mm) gap is required between the

panel and adjacent cabinets. Use the installation

block to measure the gaps.

INSTALLATION

ADJUSTING FREEZER PANEL

Installation Bloc

k

1

FOR SIDE BY SIDE MODELS - SKIP THIS STEP!

1/8"

La page charge ...

JennAir JBBFL36NHS Guide d'installation

Ce manuel convient également à

JennAir JBBFL36NHS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents