Kenmore 66513966K014 Guide d'installation

Marque: Kenmore

Modèle: 66513966K014

Taper: Guide d'installation

Ce manuel convient également à

Installation Instructions

Instrucciones de instalaci6n

Instructionsd'installation

English / Espafiol / Fran_ais

Kenmoreo

(Moddos con tina gig®hie de ®ce_o inoxidab_e}

® W

(Mod@_esa cure g6ante en acie__inoxydab_e}

P/N W10300914A

Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A.

www.kenmore.com

www.sears.com

Sears Canada inc.

Toronto, Ontario, Canada M5B 2B8

www.sears.ca

TABLEOF CONTENTS

DISHWASHER SAFETY .................................................................. 2

INSTALLATION REQUIREMENTS ................................................. 3

Tools and Parts ........................................................................................ 3

Location Requirements ........................................................................... 3

Drain Requirements ................................................................................ 5

Water Supply Requirements ................................................................ 5

Electrical Requirements ......................................................................... 5

INSTALLATION INSTRUCTIONS ................................................... 6

Prepare cabinet opening using existing utility hookups .................. 6

Prepare cabinet opening where there

are no existing utility hookups .............................................................. 7

Prepare Dishwasher ................................................................................ 9

Make Electrical Connection ................................................................ 14

Connect to water supply ..................................................................... 16

Connect to drain ................................................................................... 16

Secure dishwasher in cabinet opening ............................................. 16

JNDICE ........................................................................................ 19

TABLE DES MATIi:RES ................................................................ 36

DISHWASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Youneed to;

• Slowly open dishwasher door while someone grasps the rear of

the dishwasher. Remove shipping materials, drain hose and

lower rack. Close dishwasher door until latched.

• Observe all governing codes and ordinances.

• Install this dishwasher as specified in these instructions.

• Installation should be performed by a qualified service

technician. The dishwasher must be installed to meet all

electrical and plumbing national and local codes and

ordinances.

INSTALLATION REQUIREMENTS

Gather the required tools and parts before starting installation.

All installations

Tools needed:

• Pliers

• Phillips screwdriver

• 5,_d' and 1/4" nut drivers or

hex sockets

• Measuring tape or ruler

• 10" adjustable wrench that

opens to 11/8'' (2.9 cm)

• Flat-blade screwdriver

• Utility knife

• 2 twist-on wire connectors

which are the proper size to

connect your household

wiring to 16-gauge wiring

in dishwasher

In addition, for new installations

Tools needed:

• Cordless drill with 1/2", 3/4",

and 11/2" hole saw bits

• Small tubing cutter

• Wire stripper

• 11/2'' to 2" screw-type clamp

if connecting to waste tee

• Small level

• Flashlight

• Shallow pan

• 5/8" open-end wrench

• Bath towel

• Wood block

Parts Needed:

• 3/8" Compr x 3A" hose

fitting. Contact your local

Sears Store to purchase Kit

Number 11000.

Parts needed:

• Copper tubing (3/8"

recommended) or flexible

stainless steel braided fill

line

• Clamp connector or

conduit connector to fit a

7/8" (2.2 cm) diameter hole

Parts supplied

A. 2 - drain hose clamps, 1 large and 1 small

B. 2 - #10 x 1/2" Phillips-head screws

C. Drain hose

D. On some I<enmore Elite models, carton containing handle, hex

key and 3 setscrews.

E. On Kenmore PRO TM models, assembly containing handle, 2s/8''

mounting screws, 2 backing plates and handle installation

instruction sheet.

F. 2 - undercounter mounting brackets (top)

G. 2 - custom tape

#--_____ F T...........

Make sure all these parts are included. If they are not included, call

1-800-4-MY-HOME.

See separate parts list for accessories available for your

dishwasher.

Supplied in Kit:

• 4 Plastic studs (attached to each other by runners)

• 4 Short screws (10-16 hex head screw)

• 4 Long screws (8-18 Torx_ head screws)

• 1 Template (located inside Use and Care Guide bag assembly)

• 1 Instruction Sheet (located inside Use and Care Guide bag

assembly)

NOTE: The screws supplied are used for only 3/4" thick wooden

panel. If the wooden panel is less than 3/4" thick, customer must

purchase screws locally.

Do not run drain lines, water lines or electrical wiring where they

can interfere with or contact dishwasher motor or legs.

The location where the dishwasher will be installed must provide

clearance between motor and flooring. Motor should not touch the

floor.

Do not install dishwasher over carpeted flooring.

Shelter dishwasher and water lines leading to dishwasher against

freezing. Damage from freezing is not covered by the warranty.

A side panel kit is available from your dealer for installing your

dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part Number 4396277) is available

from your dealer for installing underneath the countertop. This may

also be obtained by calling 1-800-4-MY-HOME.

Check location where dishwasher will be installed. The location

must provide:

• easy access to water, electricity and drain.

• convenient access for loading and unloading dishes. Corner

locations require a 2" (5.1 cm) minimum clearance between the

side of the dishwasher door and the wall or cabinet.

• square opening for proper operation and appearance.

• cabinet front perpendicular to floor.

• level floor. (If floor at front of opening is not level with floor at

rear of opening, shims may be needed to level dishwasher.)

NOTE: To avoid shifting during dishwasher operation, shims must

be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a

location where it may be subject to freezing, have it winterized by

authorized service personnel.

Make sure pipes, wires and drain hose are within the shaded area

shown in the "Cutout dimensions" section.

Helpful Tip: If the floor in the dishwasher opening is uneven

(example: tile flooring only partway into opening), you will

need to be exact in measuring dimensions and in leveling

dishwasher.

t®TORX is a registered trademark of Saturn Fasteners, Inc.

Product dimensions

3/4"(1.9 crn)_

insulation =

may be

compressed

(not used on all

models)

241/2'' (62.2 crn) *-------------_

33%"

(86 cm) min.

with wheels

removed

SIDE VIEW

23%" (60.6 cm)

Cutout dimensions

24" (61 cm)

All surfaces must be

free from intrusions

12"

(30.4 cm)

31/4"

(8.3 cm)

24" (61 cm)

(5.1 cm) 10"

23/4,, 31/4 '' 31/4,, 23/4"

(7 cm) (8.3 cm) (8.3 cm) (7 cm)

Cut holes in shaded area of cabinet walls or floor as specified

below:

water line - 1/2" (1.3 cm)

drain line - 11/2'' (3.8 em)

direct wire - 3/4" (1.9 cm)

power supply cord - 11/2'' (3.8 em)

_Measured from the lowest point on the underside of eountertop.

May be reduced to 333/4 '' (85.7 cm) by removing wheels and

perforated area of insulation (blanket) on dishwasher. See the

"Prepare Dishwasher" section for more details.

_Minimum_ measured from narrowest point of opening.

_Minimum, measured from shallowest point of opening.

Use the new drain hose supplied with your dishwasher. If this is

not long enough, use a new drain hose with a maximum length

of 12 ft (3.7 m) that meets all current AHAM/IAPMO test

standards, is resistant to heat and detergent, and fits the 1"

(2.5 cm) drain connector of the dishwasher.

Connect drain hose to waste tee or disposer inlet above drain

trap in house plumbing and 20" (50.8 cm) minimum above the

floor. It is recommended that the drain hose either be looped

up and securely fastened to the underside of the counter, or be

connected to an air gap.

Air gap

• Use an air gap if the drain hose is connected to house plumbing

lower than 20" (50.8 cm) above subfloor or floor.

• Use 1/2" minimum I.D. drain line fittings.

_4 _X__ .... _ _ _ ,_

W_:_]_e_' s_spp v _(eq_,,}®_'et<_set_:s

• A hot water line with 20 to 120 psi (138 to 862 kPa) water

pressure.

• 120°F (49°C) water at dishwasher.

• 3/8" O.D. copper tubing with compression fitting or flexible

stainless steel braided fill line (1/2" minimum plastic tubing is not

recommended).

• s/s" compression x s/4" hose fitting

Do not solder within 6" (15.2 cm) of water inlet valve.

Contact a qualified electrician.

Assure that the electrical installation is adequate and in

conformance with all national and local codes and ordinances.

You must have:

• 120-volt, 60 Hz, AC-only, 15- or 20- amp, fused electrical

supply.

• Copper wire only.

We recommend:

• A time-delay fuse or circuit breaker.

• A separate circuit.

If direct wiring dishwasher:

• Use flexible, armored or nonmetallic sheathed, copper wire

with grounding wire that meets the wiring requirements for your

home and local codes and ordinances.

• Use strain relief method provided with house wiring junction

box or install a UL Listed/CSA Approved clamp connector to

the house wiring junction box. If using conduit, use a UL Listed/

CSA Approved strain relief.

If connecting dishwasher with a power supply cord:

• Use Power Supply Cord Kit (Part Number 4317824) marked for

use with dishwashers. Kit contents include:

-Volex, Inc., UL Listed 16-gauge, 3-wire power supply cord with

3 prong grounded plug.

- Neer C-500 z/s" strain relief.

- 3 wire connectors.

- Part Number 302797 grommet

Follow the kit instructions for installing the power supply cord.

• Power supply cord must plug into a mating 3 prong, grounded

outlet, located in the cabinet next to the dishwasher opening.

Outlet must meet all local codes and ordinances.

INSTALLATION INSTRUCTIONS

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Turn off water supply.

Follow the steps in this section if you are installing the

dishwasher in an existing cabinet opening with utility hookups.

If you are installing the dishwasher in a cabinet opening that

does not have hookups, follow the steps under the "Prepare

cabinet opening where there are no existing utility hookups"

section.

1. Check that the water II D!rect

line reaches to the front Water

willtheleftof opening wherewaterbe made.C°nnecti°n _re___._X_._._wire !

2. Check that the direct 6" (15,2cm.)... _

wire reaches to the

front right of opening where the electrical connection will be

made.

If the water line and the direct wire reach far enough into the

opening, proceed to the next section "Install the drain hose." If they

do not reach far enough, follow the steps under "Prepare cabinet

opening where there are no existing utility hookups."

Install the drain hose

IMPORTANT: Always use a new drain hose when installing a new

replacement dishwasher.

1. Drill a 11/2'' (3.8 cm) diameter hole in cabinet wall or floor on

the side of the opening closest to the sink.

2. Connect drain hose to waste tee or waste disposer using one of

the following methods:

• Option 1, Waste disposer - with air gap

• Option 2, No waste disposer - with air gap

• Option 3, Waste disposer - no air gap _

• Option 4, No waste disposer - no air gap _

_An air gap is recommended.

Helpful Tip: To reduce the vibration of the hose, keep the hose

away from the floor and the edge of the hole where it passes

through the cabinet.

Option 1, Waste disposer - with air gap:

1. Remove the disposer knockout plug. Cut end of drain hose if

needed (do not cut ribbed section).

2. Attach drain hose to air gap with large spring-type clamp. If

the drain hose was cut, use a 11/2'' to 2" (3.8 to 5 cm) screw-type

clamp _.

3. Use a rubber hose connector _ with spring- or screw-type

clamps _ to connect air gap to disposer inlet.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed.

gap

Large

clamp

hose

Drain trap

4. Insert drain hose through hole

cut in cabinet to the front

center of opening where

drain connection will be

made.

_Parts available from local

plumbing supply stores.

Option 2, No waste disposer - with air gap:

1. Cut end of drain hose if it needs to be cut (do not cut ribbed

section).

2. Attach drain hose to air gap with large spring-type clamp. If

the drain hose was cut, use a 11/2'' to 2" (3.8 to 5 cm) screw-type

clamp _.

3. Use a rubber hose connector _ with spring or screw-type

clamps _ to connect air gap to waste tee.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed.

Rubber hose

connector

gap

Option 4, No waste disposer - no air gap:

1. Cut end of drain hose if it needs to be cut (do not cut ribbed

section).

2. Attach drain hose to waste tee with 11/2'' to 2" (3.8 to 5 cm)

screw-type clamp _.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed. It

is recommended that the drain hose be looped up and securely

fastened to the underside of the counter.

Drain hose -

cut here if needed

Screw-type

clamp

Large

clamp

Drain

Drain trap _._ hose

4. Insert drain hose through

hole cut in cabinet to the

front center of opening

where drain connection

will be made.

_Parts available from local

plumbing supply stores.

Option 3, Waste disposer - no air gap:

1. Remove the disposer knockout plug. Do not cut end of drain

hose.

Attach drain hose to disposer inlet with large spring-type

clamp.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed. It

is recommended that the drain hose be looped up and securely

fastened to the underside of the counter.

Large spring-type J

Drain hose

Drain trap_ _'" I--I

Insert drain hose through

hole cut in cabinet to the

front center of opening

where drain connection will

be made.

tee

Drain

Insert drain hose through hole

cut in cabinet to the front

center of opening where drain

connection will be made.

_Parts available from local

plumbing supply stores.

Drain hose

hose

Electrical connection

Option 1, Direct wire method:

Helpful Tip: Wiring the dishwasher will be easier if you route

wire into the cabinet opening from the right side.

1. Drill a 3/4" (1.9 cm) hole in

right-hand cabinet side, rear

or floor. Preferred and

optional locations are shown.

2. Wood cabinet: Sand the hole

until smooth.

Metal cabinet: Cover hole

with grommet, (Part Number 302797 - not provided.)

3. Run wire into house wiring junction box.

4. Install a UL Listed/CSA Approved clamp connector (strain

relief) for flexible-type wire. If installing conduit, attach a UL

Listed/CSA Approved strain relief to the junction box.

5. Run other end of wire

through cabinet hole. Cable

must extend to the right

front of cabinet opening.

Option 2, Power supply cord method:

NOTE: A mating, 3 prong, ground-type wall receptacle is required

in a cabinet next to the dishwasher opening.

1. Drill a 11/2'' (3.8 cm)

hole in the cabinet

rear or side. Preferred

and optional

locations are shown.

2. Wood cabinet: Sand

the hole until smooth.

Metal cabinet: Cover

hole with grommet

Optional Preferred !

i.iS

(Part Number 302797) included with power supply cord kit.

Install the water line

Helpful Tip: Routing the water line through the left side of

cabinet opening will make water connection easier.

Drill a minimum 1/2" (1.3 cm) hole in the cabinet side, rear or

floor. Preferred and optional locations are shown.

2. Measure overall length

of copper tubing

required.

3. Attach copper tubing

to the water line with a

manual shutoff valve.

Copper

tubing

Slowly feed copper

tubing through hole in

cabinet. Copper tubing will bend and kink easily, so be gentle.

The copper tubing should be far enough into the cabinet

opening to connect it to dishwasher inlet on the front left of the

dishwasher.

5. Turn water shutoff valve to '_ON" position. Flush water into a

shallow pan to get rid of particles that may clog the inlet valve.

6. Turn shutoff valve to '_OFF" position.

Install the drain hose

IMPORTANT: Always use a new drain hose.

1. Drill a 11/2'' (3.8 cm)

diameter hole in

cabinet wall or floor

on the side of the

opening closest to the

sink.

2. Connect drain hose to waste tee or waste disposer using one of

the following methods:

• Option 1, Waste disposer - with air gap

• Option 2, No waste disposer - with air gap

• Option 3, Waste disposer - no air gap _

• Option 4, No waste disposer - no air gap _

_An air gap is recommended.

Helpful Tip: To reduce the vibration of the hose, keep the hose

away from the floor and the edge of the hole where it passes

through the cabinet.

Option 1, Waste disposer - with air gap:

1. Remove the disposer knockout plug. Cut end of drain hose if it

needs to be cut (do not cut ribbed section).

2. Attach drain hose to air gap with large spring-type clamp. If

the drain hose was cut, use a 11/2'' to 2" (3.8 to 5 cm) screw-type

clamp _.

3. Use a rubber hose connector _ with spring or screw-type

clamps _ to connect air gap to disposer inlet.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed.

gap

Large

clamp

hose

Drain trap

4. Insert drain hose through

hole cut in cabinet to the

front center of opening

where drain connection will

be made.

_Parts available from local

plumbing supply stores.

Option 2, No waste disposer - with air gap:

1. Cut end of drain hose if it needs to be cut (do not cut ribbed

section).

2. Attach drain hose to air gap with large spring-type clamp. If

the drain hose was cut, use a 11/2'' to 2" (3.8 to 5 cm) screw-type

clamp _.

3. Use a rubber hose connector _ with spring or screw-type

clamps _ to connect air gap to waste tee.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed.

Rubber hose

connector

gap

Large

clamp

Drain tra Drain

hose

4. Insert drain hose through

hole cut in cabinet to the

front center of opening

where drain connection will

be made.

_Parts available from local

plumbing supply stores.

Option 3, Waste disposer - no air gap:

1. Remove the disposer knockout plug. Do not cut end of drain

hose.

Attach drain hose to disposer inlet with large spring-type

clamp.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed. It

is recommended that the drain hose be looped up and securely

fastened to the underside of the counter.

Large spring-type J

_ Drain hose

Drain trap_ _ I--I

Insert drain hose through

hole cut in cabinet to the

front center of opening

where drain connection will

be made.

Option 4, No waste disposer - no air gap:

1. Cut end of drain hose if it needs to be cut (do not cut ribbed

section).

2. Attach drain hose to waste tee with 11/2'' to 2" (3.8 to 5 cm)

screw-type clamp _.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed. It

is recommended that the drain hose be looped up and securely

fastened to the underside of the counter.

Drain hose -

cut here if needed

Screw-type

clamp

tee

Drain

3. Insert drain hose through

hole cut in cabinet to the

front center of opening

where drain connection will

be made.

_Parts available from local

plumbing supply stores.

hose

_,j _, '__j_:_ _, '_C__

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Helpful Tip: Put cardboard under dishwasher until it is installed

in cabinet opening. The cardboard will help avoid damage to

floor covering during installation.

Using 2 or more people, grasp the sides of dishwasher door

frame and put the dishwasher on its back, resting on top of the

corner posts.

Remove 2 screws attaching access panel and lower panel to

dishwasher using a 1/4" hex socket, nut driver or Phillips

screwdriver.

3. Removepanelsandsetpanelsasideonacoveredsurface.

4. Checkthatgroundingclipisattachedtothelowerpanel.

5°

Lower

panel

clip

Slide nut and ferrule onto tubing.

Copper tubing only: Slide nut, then ferrule, about 1" (2.5 cm)

onto copper tubing.

NOTE: To avoid vibration during operation, route the water

supply line so that it does not touch the dishwasher base, frame

or motor.

6. Add 90 ° elbow fitting to the water supply line.

Connect the 3/8" compression fitting to the water supply line

prior to installing the unit into the cabinet opening. Attach such

that the 3/4" connection is facing upward.

Copper tubing only: Put the tubing into the 90 ° elbow fitting as

far as it will go (the copper tubing bends and kinks easily).

Slide the nut and ferrule forward and start the nut onto the

elbow threads. Flexible braided connection: Secure nut to

elbow using 5/8" open ended wrench or adjustable wrench.

NOTE: Do not use Teflon ®t tape with compression fittings.

Remove terminal box cover.

- If you are direct wiring: Install a UL Listed/CSA Approved

clamp connector to the terminal box. If using conduit, use a

UL Listed/CSA Approved strain relief.

- If you are installing a power supply cord kit, do so now,

following kit instructions. The power supply cord kit must be

UL Listed and marked for use with dishwashers (that is, Power

Supply Cord Kit Part Number 4317824).

8°

. Terminal

I....................................................................................q_ box cover

_/ _" #_j_ CaBle clamp

connector

Dishwasher wires

Measure height of cabinet opening

from underside of countertop to

floor where dishwasher will be

installed (you need the lowest

point). Check chart for that height

opening. Put wheels in the required

position.

¢- 2

Wheel_ 3

Minimum

cutout height

333/4'' (85.7 cm)

33%" (86 cm)

34" (86.4 cm)

341¼'' (87 cm)

341/2'`(87.6 cm)

Wheel

position

remove

iNumber of

turns on

front leg

all the

way up

all the

way up

Perforation

on Blanket

remove

keep

9°

Turn both front leveler legs to the same

height.

If the minimum cutout height is less than 34"

(86.4 cm), the rear wheels can be removed

for additional clearance. This will allow the

dishwasher to fit into a 337/8'' (86 cm) high

cutout, but the dishwasher will be more

difficult to move into position. If the wheels

Front leg

are removed, cover the floor when moving the dishwasher.

If the minimum cabinet opening height is 333/4" (85.7 cm), a

section in the insulation blanket can be removed by cutting

along the perforation.

t®Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.

Install the door handle (some Kenmore Elite models)

NOTES:

• To ease installation, using two or more people, place the

dishwasher on its back.

• To avoid scratching the front panel, place a soft cloth or towel

against the panel while installing the door handle.

• Setscrews are preinstalled in the handle.

1. Remove the door handle and hardware bag containing the hex

key from the bubble pouch.

2. Place the handle on the mounting studs. The setscrews should

face down when installed correctly. If the handle is installed

upside down, proper installation will not be possible.

3. Push the door handle tightly against the door.

4. Insert the short end of the hex key into the setscrew and tighten

1¼turn past snug. Setscrew will not be recessed into the handle.

5. Repeat Step 4 for other setscrew.

6. Keep the hex key with the Installation Instructions.

NOTE: The handle installation procedure should take less than

5 minutes.

Hole in panel f_/Mounting stud

Locating feature/- // 'd

// I

Door handle

Setscrew

Install the door handle (Kenmore PROTM models)

IMPORTANT: Do not scratch the front panel during this procedure.

1. Remove the door handle assembly from the upper dishrack of

the dishwasher.

Remove and discard the handle packaging. Be sure to retain

the handle installation instructions and mounting hardware.

Install the door

handle according to

the handle

installation

instructions provided

with the handle

assembly.

Install custom panel

Follow steps below:

A customer supplied panel must weigh no more than 16 Ibs (7.3 kg)

and must be made to specific dimensions. It is recommended that a

cabinetmaker cut the customer panel because of the precise

dimensions needed.

NOTES:

The handle for the custom panel is not included.

All mounting hardware supplied is for a 3¼,,(19.1 cm) thick

wood panel. If a thinner wood panel or materials other than

wood are used, it is the customer's responsibility to obtain the

proper length screws and adjust the pilot holes accordingly.

IMPORTANT: Use a moisture resistant sealer on both sides and all

edges of the panel to avoid damage from moisture.

Custom panel installation - Dishwashers with control panel on

the top.

235/8,,

(60 cm) "2929/32'' (76 cm)

¾" (19.1 ram)

_This dimension is for 4" (10.2 cm) toe kick. If the installation

needs a higher toe kick, adjust the height of the wood panel

accordingly. Not recommended for toe kicks greater than 6"

(15.2 cm).

2. Install the custom hardware handle(s) on the front of the

wooden panel inside dotted line.

IMPORTANT: If the handle is attached from the back of the custom

panel, the screw holes should be countersunk for the screw heads to

be flush with the panel. If the handle is attached to the front of the

custom panel, the screw lengths cannot exceed the panel thickness.

Top Of Panel

T_p_ delpanel

Oessusdepanneau

Using the template provided attached it to the backside of the

custom panel with tape. Make sure that the center of the

template is aligned with the center of the wooden panel and

top of the template is aligned to the top face of the wooden

panel.

6. Attach the 4 plastic studs to the wooden panel using the 4 short

hex head (5,_61')screws provided.

NOTE: Do not drill deeper then 5/8" to keep from drilling through

panel. Pilot hole depths given are for 3A" thick panel.

4. Mark 4 pilot holes on the wooden panel using the template

provided. Predrill four pilot holes using a 3/32" drill bit. Use tape

to mark the drill bit to gauge hole depth. Drill pilot holes

approximately 5/8" into the custom panel.

Plastic studs attached

with 4 short screws

Visible side

Wooden panel

assembly

Align the studs on the custom wood panel to the keyhole slots

on the door assembly. Ensure that all 4 plastic studs are

engaged in the keyhole slots. Slide wood panel down until the

top surface of the wooden panel is flush with the top of the

door.

Align top

edges

Check custom tape alignment with metal door slots; verify tape

is right-side up, and that the tape does not overhang the metal

door on the top, bottom or side interfaces. Remove the backing

from the custom tape by pulling straight down on the liner.

Align the custom tape to the keyhole slots on the metal door

(see image) and apply. Repeat steps for one side and then the

other.

NOTE: The adhesive on the tape is aggressive, so proper

alignment and attachment to the metal door needs to occur on

the first try.

Drill through

these holes.

Customer-su

panel Remo_ 2 short screws

and replace with long

screws provided.

Open the door and align top edges. Predrill two pilot holes

using a 3/32"drill bit. Use tape to mark the drill bit to gauge hole

depth. Drill pilot holes approximately 11/2'' (12.7 mm) into the

top corners of the door using hole in liner as a guide.

Customer-supplied

panel

1¾" Screw

edges

)rill through

these holes

9°

Install 2 long screws supplied in top corners to secure custom

wood panel in place.

Option 2, Dishwasher with Stainless Steel Tub Side

Attachment

(for marble, granite or other hard surface countertops)

NOTE: You must drill pilot holes in cabinet to avoid splitting the

wood before installing screws.

1. Remove the brackets from the parts package.

2. Break off the end of the bracket along the scored line.

Score

Nne

gn top

edges

Remove 2 short scre_ 3lied

and replace with long panel

screws provided.

10. Remove the short screws (3rd from top) on either side of the

inner door panel. Predrill 2 pilot holes using a 3/32" drill bit. Use

tape to mark the drill bit to gauge the hole depth. Drill pilot

holes approximately 11/2'' (12.7 mm) using the door liner hole as

a guide into the panel. Install the two remaining long screws.

Choose attachment option

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Using 2 or more people, stand the dishwasher up.

IMPORTANT: The dishwasher must be secured to the cabinet. There

are 2 brackets found in the parts bag. Attach the brackets to the

top of the dishwasher if the countertop is wood, laminate or

another similar surface. If your countertop is marble, granite or

another hard surface, install using Option 2.

Option 1, Countertop attachment

1. Remove the brackets from the package and place in the open

slots on the left- and right-hand top of the dishwasher collar as

shown.

Tabs must

2. Insert the bracket into the slot on the collar. Using a pair of

pliers, bend the tab down to secure the bracket in place.

Repeat this step for the other side.

3°

With another person holding the dishwasher to keep it from

tipping, open dishwasher door, and place towel over pump

assembly and spray arm of dishwasher. This will keep screws

from falling into pump area when securing dishwasher to

cabinet.

Push the plastic buttons out of the side of the tub.

NOTE: Save the buttons to cover the holes after dishwasher is

installed.

Plastic

button '

Push bracket into slot on the side of dishwasher, and bend tab

in toward the side of the dishwasher so that it keeps the

bracket in place.

NOTE: Do not attach the dishwasher. This will be done later.

Bend

Option 3, Dishwasher with Plastic Tub Side Attachment

(for marble, granite or other hard surface countertops)

6. Order Mounting Bracket Kit Part Number 8212560.

Check door spring tension

With another person holding the dishwasher to keep it from

tipping, open and close the door a few times. If the door closes

or falls open under its own weight, the door tension will need to

be adjusted.

2. To adjust the door spring tension, unhook the spring from the

rear leg of dishwasher.

3. With a 5_6" nut driver or hex socket, remove the screw from the

tensioner.

The screw can be put into one of three holes 1, 2, 3 in front leg

of dishwasher. If the door closes by itself, move the tensioner to

a higher number hole and replace screw. When door is

unlatched, if it opens by itself, move tensioner to a lower

numbered hole and replace screw.

NOTE: Do not attach the dishwasher. This will be done later.

Reattach door spring to rear leg. Tensioners on both sides of

dishwasher should be secured at same holes.

oner

-Sjw

1 2 3

Move dishwasher into cabinet opening

Using 2 or more people, stand the dishwasher up.

Grasp the sides of the dishwasher at the

edges of the door panel.

Tilt dishwasher backward on wheels and

move dishwasher close to cabinet

opening. Do not push on the front of the

panel or on the console -- they may

dent.

If dishwasher has a power supply cord, insert power supply

cord into hole cut into cabinet.

If using direct wire, check that it is on the right front side of

opening.

5. Check that water line is on the left side of opening and drain

hose is near the center of the hole in the cabinet.

6. Slowly move dishwasher completely into cabinet opening. Do

not kink or pinch copper tubing, drain hose, power supply cord

or direct wire between dishwasher and cabinet.

Helpful Tip: Once the dishwasher is in position, you may have

to support the front of the dishwasher by raising, lowering or

shimming front feet.

7. Remove cardboard from under dishwasher.

8. Using the precut slots in the insulation, attach the insulation to

the sides of the tub using the molded hooks on each side of the

tub.

NOTE: It is all right if dishwasher fits tightly into cabinet opening.

Do not remove insulation blanket -- the blanket reduces the sound

level.

Level the dishwasher

Align front of dishwasher door panel with cabinet doors. You

may need to adjust alignment to be even with your cabinets.

Helpful Tip: Prop up one side of frame to hold dishwasher up

off floor when adjusting front legs.

With some installations, it may be easier to adjust the front leg

using the %6" hex head.

Check that leveling legs are firmly against the floor.

Place level against top front

opening of tub. Check that

dishwasher is level from side to

side. If dishwasher is not level,

adjust front legs up or down until

dishwasher is level.

Close and latch the door. Place the level against the front of

the dishwasher to check to see if it is vertically aligned.

If needed, adjust rear leveling leg by using a Phillips

screwdriver to adjust the back of the unit. Turn the rear leveler

located on the front left hand side of the lower compartment

counterclockwise to raise the back of the unit.

Check "Electrical Requirements" section.

You need to."

• have the correct electrical supply and recommended

grounding method.

If you are:

• direct wiring, use Option 1

• using a power supply cord, use Option 2

Option 1, Direct wire method

1. Route direct wire so that it does not touch dishwasher motors or

lower part of dishwasher tub.

5°

Pull direct wire through hole in terminal box.

Helpful Tip:

• Select the proper size twist-on

connectors to connect your household

wiring to 16-gauge dishwasher wiring. .......

• Insert wire ends into twist-on connector.

Do not pre-twist bare wire.

• Twist connector.

• Gently tug on wires to be sure both are secured.

Connect the wires as follows using twist-on connectors sized to

connect direct wire to 16-gauge dishwasher wire:

Power supply wire: Terminal box wire:

white--white

black--black

ground wire_e-_green ground connector

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord.

Failure to foflow these instructions can result in

death, fire, or electrical shock.

Form bare ground wire into a U-shaped hook. Wrap ground

wire hook clockwise around ground connector and under the

washer.

Securely tighten ground connector.

Ground wire Washer

Ground

connector

Option 2, Power supply cord method

1. Route the power supply cord so that it does not touch

dishwasher motors or lower part of dishwasher tub.

2. Pull the direct wire through hole in terminal box.

Helpful Tip:

• Select the proper size twist-on

connectors to connect your household

wiring to 16-gauge dishwasher wiring. __,F',

• Insert wire ends into UL Listed/CSA ,.,

Approved twist-on connector. Do not

pre-twist bare wire.

• Twist connector.

• Gently tug on wires to be sure both are

secured.

3. Connect the wires as follows using twist-on connectors sized to

connect power supply cord to 16-gauge dishwasher wire:

Power supply wire: Terminal box wire:

white--white

black--b Jack

ground wire--green ground connector

Electrical Shock Hazard

Electricafly ground dishwasher,

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord,

Failure to follow these instructions can result in

death, fire, or electrical shock.

Ground wire

Tighten clamp connector or

conduit connector screws.

Reinstall terminal box cover

with wires inside terminal box.

The cover must be outside the box on

the left side.

8. Make sure no wires are pinched by

cove_

....... i

4. Form bare ground wire into a U-shaped hook. Wrap ground

wire hook clockwise around ground connector and under the

washer.

5. Securely tighten ground connector.

Ground wire Washer

Ground

connector

Ground wire

Tighten clamp connector or conduit

connector screws.

ScrewL__

__ ....

7. 4. Place the smaller drain hose clamp onto the small end of the

drain hose.

Reinstall terminal box cover with

wires inside terminal box.

The cover must be outside the box on

the left side.

8. Make sure no wires are pinched by

cover.

9. Do not plug the dishwasher cord into the outlet until instructed

to do so.

10. Check that power supply cord does not touch dishwasher motor

or lower part of dishwasher tub.

Tighten 90 ° elbow fitting to valve.

Be sure rubber washer is properly seated in fitting. Slide the 3/4"

fitting up to the valve and hand tighten to avoid unintentional

cross-threading. Hand tighten until the coupling is tight. Using

pliers, check the tightness of the coupling. An additional 1/4 to

1/2turn may be required to seal the rubber gasket.

NOTE: Do not overtighten. Damage to the coupling can result.

Check for leaks.

J[ . _'i_¸).....

Place paper towel under 90 ° elbow fitting. Turn on water

supply and check for leaks. If leak occurs, repeat previous step.

To help minimize vibration,

route drain hose to avoid

contact with motor, door

springs, water line, cabinet,

flooring or the edge of the

hole where it passes

through the cabinet.

Do not remove drain loop

from side of dishwasher.

Place pan under end of

drain hose. Pan will collect

J,,

i i i i

_'\ i \ J

_" -- _----- Drain ] /

any water in drain hose.

Hose clamp

Push the drain hose into the connector up to the stop on the

drain hose.

Connector Stop

Use pliers to open clamp and slide clamp onto connector

between stops on connector as shown.

Hose clamp

Stops

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts,

1. If you have not already done so, open dishwasher door and

place towel over pump assembly and spray arm of dishwasher.

This will keep screws from falling into pump area if you

unintentionally drop them when securing dishwasher to

countertop.

2. Check that dishwasher is still level and centered side to side in

the opening.

3. Secure dishwasher to countertop or sides of cabinet with 2,

#10 x 1/2" Phillips-head screws. The dishwasher must be secured

to keep it from tipping when door is opened.

Screw to countertop Screw to

side cabinet

NOTE: You must drill pilot holes in cabinet to avoid splitting

the wood before installing screws.

Open door about 3" (7.6 cm) and check that space between

inner door and tub is equal on both sides. If spacing is not

equal, loosen bracket screws and shift tub. Tighten bracket

screws.

If using a countertop attachment to secure dishwasher, check

that top of door does not contact screws, brackets, or

countertop. If it does, dishwasher must be lowered and re-

leveled.

6. If securing with a side attachment, check that sides of door do

not rub against the screw heads. If they do, dishwasher must be

re-centered.

7. Remove towel from dishwasher.

8. Reinstall the lower dish rack.

Complete installation

Check that grounding clip is attached to the lower panel.

Place the lower panel behind the access panel. Some models

have insulation on the access panel which must fall behind the

insulation on the lower panel.

Grounding

clip

3. Hold the two panels together and place them against

dishwasher leg.

4. Reinstall the screws through the holes in the access panel and

the slots in the lower panel. Install right side screw first.

Direct wire method:

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Power supply cord method:

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result

in death, fire, or electrical shock.

7. Reconnect power or plug in dishwasher.

5. Check that the lower edge of the lower panel contacts the

floor.

6. Tighten the screws.

Check operation

1. Read the Use and Care Guide that came with your dishwasher.

2. Check that all parts have been installed and no steps were

skipped.

3. Check that you have all the tools you used.

4. Start dishwasher and allow it to complete the shortest wash

cycle. After the first 2 minutes, unlatch door, wait 5 seconds,

then open door.

5. Check to see that there is water in the bottom of the dishwasher

tub. Check that dishwasher is working properly.

6. If the dishwasher is not working properly, disconnect power or

unplug dishwasher and see "If dishwasher does not operate"

section.

If dishwasher does not operate

First try the solutions suggested here to possibly avoid the cost of a

service call.

• Has the circuit breaker tripped or the house fuse blown?

• Isthe door closed tightly and latched?

• Has the cycle been set correctly to start the dishwasher?

• Isthe water turned on?

If none of these work, call 1-800-4-MY-HOME.

INDICE

SEGURIDAD DE LA LAVAVAJILLAS ............................................ 19

REQUISITOS DE INSTALACI6N ................................................. 20

Herramientas y piezas ......................................................................... 20

Requisitos de ubicaci6n ....................................................................... 20

Requisitos de desagOe ......................................................................... 22

Requisitos del suministro de agua ..................................................... 22

Requisitos el&ctricos ............................................................................. 22

INSTRUCCIONES DE INSTALACION .......................................... 23

Prepare la abertura del armario usando

las conexiones de servicio existentes ................................................ 23

Prepare la abertura del armario donde

no existen conexiones de servicio ...................................................... 24

Prepare la lavavajillas ......................................................................... 26

Conexi6n el&ctrica ................................................................................ 32

Conexi6n al suministro de agua ......................................................... 33

Conexi6n al desagOe ............................................................................ 34

Asegure la lavavajillas en la abertura del armario ....................... 34

SEGURIDAD DE LA LAVAVAJILLAS

Su seguridad y la seguridad de los demos es muy importante.

Hemos incluJdo muchos mensajes Jmportantes de seguridad en este manual yen su electrodomestico. Lea y obedezca siempre

todos los mensajes de segurJdad.

Este es el sfmbolo de advertencia de seguridad.

Este simbolo le llama la atenci6n sobre peligros potenciales que pueden ocasionar la muerte o una lesi6n a

usted y a los dem_.s.

Todos los mensajes de seguridad iran a continuaci6n del sfmbolo de advertencia de seguridad y de la palabra

"PELIGRO" o "ADVERTENCIA". Estas palabras significan:

Si no sigue las instrucciones de inmediato, usted puede

morir o sufrir una lesi6n grave.

Si no sigue las instrucciones, usted puede morir o sufrir

una lesion grave.

Todos los mensajes de seguridad le diran el peligro potencJal, le diran c6mo reducir las posibJlidades de sufrJr una lesi6n y Io que

puede suceder si no se siguen las instrucciones.

Pe|igro de Vuelco

No use la lavavajillas antes de estar completarnente

instalada.

No se apoye en la puerta abierta.

No seguir estas instrucciones puede ocasionar heridas

serias o cortaduras.

Usted necesita=

• Abrir lentamente la puerta de la lavavajillas mientras alguien

sujeta la parte trasera de la lavavajillas. Quite los materiales

de env_o, la manguera de desagge y la canasta inferior. Cierre

la puerta de la lavavajillas hasta que quede asegurada.

Cumplir con todos los c6digos y reglamentos vigentes.

Instalar la lavavajillas seg0n se especifica en estas

instrucciones.

La instalaci6n debe ser hecha por un t&cnico de servicio

calificado. La lavavajillas debe instalarse de acuerdo con

todos los c6digos y reglamentos el&ctricos y de plomer_a

nacionales y locales.

REQUISITOSDE INSTALACION

Retina las herramientas y piezas necesarias antes de comenzar la

instalaci6n.

Todas las instalaciones

Herramientas necesarias- •

• Pinzas •

• Destornillador Phillips •

• Llaves de tuercas o •

casquillos hexagonales de

5_6" y 1/4"

• Cinta de medir o regla

• Llave ajustable de 10" que

se abra a 11/8'' (2,9 cm)

• Destornillador de hoja plana

• Cuchillo de uso general

• 2 conectores de empalme

retorcido para alambre

que tengan el tama_o

adecuado para conectar el

cableado de su hogar al

cableado calibre 16 de la

lavavajillas

Adem6s, para nuevas instalaciones

Herramientas necesarias:

• Taladro inal6mbrico con •

brocas de sierra perforadora

de 1/2", 3_" y 11/2,,

• Cortatubos peque_o

• Pelacables •

• Abrazadera tipo tornillo de

11/2'' a 2" si se ha de

conectar al tubo de

desperdicios

Nivel peque_o

Linterna

Recipiente poco profundo

Llave ajustable de %"

Toalla de ba_o

Bloque de madera

Piezas necesarias:

• Conector a compresi6n de

3/8" x conector de

manguera de 3/4". P6ngase

en contacto con la tienda

local de Sears para

comprar el Juego N °

11000.

Piezas necesarias:

Tuberia de cobre (se

recomienda de 3/8") o Ifnea

de Ilenado flexible de

acero inoxidable

Conector de abrazadera o

conector de conductos que

quepa en un orificio de 7/8"

(2,2 cm) de di6metro

Piezas provistas

A. 2 abrazaderas para la manguera de desagOe: 1grande y 1peque_a

B. 2 tornillos Phillips No. 10 x 1/2"

C. Manguera de desagOe

D. En algunos modelos Kenmore Elite, un cart6n conteniendo una

manija, Ilave hexagonal y 3 tornillos opresores

E. En los modelos Kenmore PRO TM, juego con manija, 2 tornillos de

montaje de 5/8", 2 placas de soporte y una hoja de instrucciones

para instalar la manija.

F. 2 soportes de montaje (superior) para el mostrador

G. 2 Cinta personalizada

Aseg6rese de que todas las piezas est&n incluidas. Si no Io est6n,

Ilame al 1-800-4-MY-HOME.

Vea la lista de piezas que viene por separado para ver qu&

accesorios est6n disponibles para su lavavajillas.

Se incluye en el juego:

• 4 taquetes de pl6stico (sujetados unos a los otros con

correderas)

• 4 tornillos cortos (tornillo de cabeza hexagonal 10-16)

• 4 tornillos largos (tornillos de cabeza Torx _t 8-18)

• 1 plantilla (ubicada adentro de la bolsa del Manual de uso y

cuidado para el ensamblaje)

• 1 hoja de instrucciones (ubicada adentro de la bolsa del

Manual de uso y cuidado para el ensamblaje)

NOTA: Los tornillos provistos se utilizan 6nicamente para un panel

de madera de 3/_" de grosor. Si el panel de madera tiene un

grosor menor a 3¼", el cliente debe adquirir los tornillos en su

Iocalidad.

No instale tuberias de agua o desagOe ni cableado el&ctrico donde

puedan interferir o hacer contacto con el motor o las patas de la

lavavajillas.

El lugar donde se instalar6 la lavavajillas debe permitir un espacio

libre entre el motor y el piso. El motor no debe tocar el piso.

No instale la lavavajillas sobre piso alfombrado.

Proteja la lavavajillas y las lineas de agua que van a la lavavajillas

contra el congelamiento. La garantia no cubre daBos por

congelaci6n.

Puede obtener un juego de panel lateral con el distribuidor para

instalar su lavavajillas en el extremo del armario.

Su distribuidor tiene un accesorio que funciona como barrera

contra la humedad (Pieza N ° 4396277) para ser instalado debajo

del mostrador. Este puede obtenerse tambi&n Ilamando al

1-800-4-MY-HOME.

Revise el lugar donde instalar6 la lavavajillas. El lugar debe

proveer:

• F6cil acceso a instalaciones de agua, electricidad y desagOe.

• Facilidad para cargar y descargar la lavavajillas. Los rincones

deben tener un espacio libre minimo de 2" (5,1 cm) entre el

costado de la puerta de la lavavajillas y la pared o el armario.

Una abertura cuadrada para que la lavavajillas funcione y se

vea bien.

• La parte frontal del armario que sea perpendicular al piso.

• Piso nivelado. (Si el piso en la parte delantera de la abertura

no est6 nivelado con el piso en la parte trasera de la abertura,

puede usar cu_as para nivelar la lavavajillas.)

NOTA: Las cu_as deben adherirse con firmeza al piso para evitar

que se muevan cuando se est& usando la lavavajillas.

Siva a dejar la lavavajillas sin uso por cierto tiempo o en un lugar

donde pudiera congelarse, haga que un miembro del personal de

servicio autorizado la prepare para el invierno.

Aseg6rese de que la tuberia, los cables el&ctricos y la manguera de

desagOe est&n en el 6rea sombreada que se muestra en la secci6n

"Dimensiones de corte".

Consejo Otil: Si el piso de la abertura donde colocar6 la

lavavajillas no es parejo (por ejemplo: piso con Iosetas s61o

hasta cierta parte de la abertura), deber6 ser exacto para

tomar las medidas y nivelar la lavavajillas.

_®TORXes unamarca registrada de Saturn Fasteners,Inc.

La page charge ...

Kenmore 66513966K014 Guide d'installation

Marque: Kenmore

Modèle: 66513966K014

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Kenmore 66513966K014 Installation guide
español: Kenmore 66513966K014 Guía de instalación

Kenmore 66513966K014 Guide d'installation

Ce manuel convient également à

Kenmore 66513966K014 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents