Kenmore 66512776K312 Guide d'installation

Taper
Guide d'installation

Ce manuel convient également à

Installation Instructions
Instrucciones de instalaci6n
Instructionsd'installation
English / Espafiol / Fran_ais
Kenmoreo
(Moddos con tina gig®hie de ®ce_o inoxidab_e}
® W
(Mod@_esa cure g6ante en acie__inoxydab_e}
P/N W10300914A
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
www.sears.com
Sears Canada inc.
Toronto, Ontario, Canada M5B 2B8
www.sears.ca
TABLEOF CONTENTS
DISHWASHER SAFETY .................................................................. 2
INSTALLATION REQUIREMENTS ................................................. 3
Tools and Parts ........................................................................................ 3
Location Requirements ........................................................................... 3
Drain Requirements ................................................................................ 5
Water Supply Requirements ................................................................ 5
Electrical Requirements ......................................................................... 5
INSTALLATION INSTRUCTIONS ................................................... 6
Prepare cabinet opening using existing utility hookups .................. 6
Prepare cabinet opening where there
are no existing utility hookups .............................................................. 7
Prepare Dishwasher ................................................................................ 9
Make Electrical Connection ................................................................ 14
Connect to water supply ..................................................................... 16
Connect to drain ................................................................................... 16
Secure dishwasher in cabinet opening ............................................. 16
JNDICE ........................................................................................ 19
TABLE DES MATIi:RES ................................................................ 36
DISHWASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Youneed to;
Slowly open dishwasher door while someone grasps the rear of
the dishwasher. Remove shipping materials, drain hose and
lower rack. Close dishwasher door until latched.
Observe all governing codes and ordinances.
Install this dishwasher as specified in these instructions.
Installation should be performed by a qualified service
technician. The dishwasher must be installed to meet all
electrical and plumbing national and local codes and
ordinances.
2
INSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
All installations
Tools needed:
Pliers
Phillips screwdriver
5,_d' and 1/4" nut drivers or
hex sockets
Measuring tape or ruler
10" adjustable wrench that
opens to 11/8'' (2.9 cm)
Flat-blade screwdriver
Utility knife
2 twist-on wire connectors
which are the proper size to
connect your household
wiring to 16-gauge wiring
in dishwasher
In addition, for new installations
Tools needed:
Cordless drill with 1/2", 3/4",
and 11/2" hole saw bits
Small tubing cutter
Wire stripper
11/2'' to 2" screw-type clamp
if connecting to waste tee
Small level
Flashlight
Shallow pan
5/8" open-end wrench
Bath towel
Wood block
Parts Needed:
3/8" Compr x 3A" hose
fitting. Contact your local
Sears Store to purchase Kit
Number 11000.
Parts needed:
Copper tubing (3/8"
recommended) or flexible
stainless steel braided fill
line
Clamp connector or
conduit connector to fit a
7/8" (2.2 cm) diameter hole
Parts supplied
A. 2 - drain hose clamps, 1 large and 1 small
B. 2 - #10 x 1/2" Phillips-head screws
C. Drain hose
D. On some I<enmore Elite models, carton containing handle, hex
key and 3 setscrews.
E. On Kenmore PRO TM models, assembly containing handle, 2s/8''
mounting screws, 2 backing plates and handle installation
instruction sheet.
F. 2 - undercounter mounting brackets (top)
G. 2 - custom tape
B
#--_____ F T...........
G
Make sure all these parts are included. If they are not included, call
1-800-4-MY-HOME.
See separate parts list for accessories available for your
dishwasher.
Supplied in Kit:
4 Plastic studs (attached to each other by runners)
4 Short screws (10-16 hex head screw)
4 Long screws (8-18 Torx_ head screws)
1 Template (located inside Use and Care Guide bag assembly)
1 Instruction Sheet (located inside Use and Care Guide bag
assembly)
NOTE: The screws supplied are used for only 3/4" thick wooden
panel. If the wooden panel is less than 3/4" thick, customer must
purchase screws locally.
Do not run drain lines, water lines or electrical wiring where they
can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must provide
clearance between motor and flooring. Motor should not touch the
floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher against
freezing. Damage from freezing is not covered by the warranty.
A side panel kit is available from your dealer for installing your
dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277) is available
from your dealer for installing underneath the countertop. This may
also be obtained by calling 1-800-4-MY-HOME.
Check location where dishwasher will be installed. The location
must provide:
easy access to water, electricity and drain.
convenient access for loading and unloading dishes. Corner
locations require a 2" (5.1 cm) minimum clearance between the
side of the dishwasher door and the wall or cabinet.
square opening for proper operation and appearance.
cabinet front perpendicular to floor.
level floor. (If floor at front of opening is not level with floor at
rear of opening, shims may be needed to level dishwasher.)
NOTE: To avoid shifting during dishwasher operation, shims must
be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the shaded area
shown in the "Cutout dimensions" section.
Helpful Tip: If the floor in the dishwasher opening is uneven
(example: tile flooring only partway into opening), you will
need to be exact in measuring dimensions and in leveling
dishwasher.
t®TORX is a registered trademark of Saturn Fasteners, Inc.
Product dimensions
3/4"(1.9 crn)_
insulation =
may be
compressed
(not used on all
models)
241/2'' (62.2 crn) *-------------_
33%"
(86 cm) min.
with wheels
removed
SIDE VIEW
23%" (60.6 cm)
Cutout dimensions
24" (61 cm)
All surfaces must be
free from intrusions
12"
(30.4 cm)
31/4"
(8.3 cm)
24" (61 cm)
(5.1 cm) 10"
23/4,, 31/4 '' 31/4,, 23/4"
(7 cm) (8.3 cm) (8.3 cm) (7 cm)
Cut holes in shaded area of cabinet walls or floor as specified
below:
water line - 1/2" (1.3 cm)
drain line - 11/2'' (3.8 em)
direct wire - 3/4" (1.9 cm)
power supply cord - 11/2'' (3.8 em)
_Measured from the lowest point on the underside of eountertop.
May be reduced to 333/4 '' (85.7 cm) by removing wheels and
perforated area of insulation (blanket) on dishwasher. See the
"Prepare Dishwasher" section for more details.
_Minimum_ measured from narrowest point of opening.
_Minimum, measured from shallowest point of opening.
4
Use the new drain hose supplied with your dishwasher. If this is
not long enough, use a new drain hose with a maximum length
of 12 ft (3.7 m) that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, and fits the 1"
(2.5 cm) drain connector of the dishwasher.
Connect drain hose to waste tee or disposer inlet above drain
trap in house plumbing and 20" (50.8 cm) minimum above the
floor. It is recommended that the drain hose either be looped
up and securely fastened to the underside of the counter, or be
connected to an air gap.
Air gap
IL
Use an air gap if the drain hose is connected to house plumbing
lower than 20" (50.8 cm) above subfloor or floor.
Use 1/2" minimum I.D. drain line fittings.
_4 _X__ .... _ _ _ ,_
W_:_]_e_' s_spp v _(eq_,,}®_'et<_set_:s
A hot water line with 20 to 120 psi (138 to 862 kPa) water
pressure.
120°F (49°C) water at dishwasher.
3/8" O.D. copper tubing with compression fitting or flexible
stainless steel braided fill line (1/2" minimum plastic tubing is not
recommended).
s/s" compression x s/4" hose fitting
Do not solder within 6" (15.2 cm) of water inlet valve.
Contact a qualified electrician.
Assure that the electrical installation is adequate and in
conformance with all national and local codes and ordinances.
You must have:
120-volt, 60 Hz, AC-only, 15- or 20- amp, fused electrical
supply.
Copper wire only.
We recommend:
A time-delay fuse or circuit breaker.
A separate circuit.
If direct wiring dishwasher:
Use flexible, armored or nonmetallic sheathed, copper wire
with grounding wire that meets the wiring requirements for your
home and local codes and ordinances.
Use strain relief method provided with house wiring junction
box or install a UL Listed/CSA Approved clamp connector to
the house wiring junction box. If using conduit, use a UL Listed/
CSA Approved strain relief.
If connecting dishwasher with a power supply cord:
Use Power Supply Cord Kit (Part Number 4317824) marked for
use with dishwashers. Kit contents include:
-Volex, Inc., UL Listed 16-gauge, 3-wire power supply cord with
3 prong grounded plug.
- Neer C-500 z/s" strain relief.
- 3 wire connectors.
- Part Number 302797 grommet
Follow the kit instructions for installing the power supply cord.
Power supply cord must plug into a mating 3 prong, grounded
outlet, located in the cabinet next to the dishwasher opening.
Outlet must meet all local codes and ordinances.
INSTALLATION INSTRUCTIONS
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
1. Disconnect power.
2. Turn off water supply.
Follow the steps in this section if you are installing the
dishwasher in an existing cabinet opening with utility hookups.
If you are installing the dishwasher in a cabinet opening that
does not have hookups, follow the steps under the "Prepare
cabinet opening where there are no existing utility hookups"
section.
1. Check that the water II D!rect
line reaches to the front Water
willtheleftof opening wherewaterbe made.C°nnecti°n _re___._X_._._wire !
2. Check that the direct 6" (15,2cm.)... _
wire reaches to the
front right of opening where the electrical connection will be
made.
If the water line and the direct wire reach far enough into the
opening, proceed to the next section "Install the drain hose." If they
do not reach far enough, follow the steps under "Prepare cabinet
opening where there are no existing utility hookups."
Install the drain hose
IMPORTANT: Always use a new drain hose when installing a new
replacement dishwasher.
1. Drill a 11/2'' (3.8 cm) diameter hole in cabinet wall or floor on
the side of the opening closest to the sink.
2. Connect drain hose to waste tee or waste disposer using one of
the following methods:
Option 1, Waste disposer - with air gap
Option 2, No waste disposer - with air gap
Option 3, Waste disposer - no air gap _
Option 4, No waste disposer - no air gap _
_An air gap is recommended.
Helpful Tip: To reduce the vibration of the hose, keep the hose
away from the floor and the edge of the hole where it passes
through the cabinet.
Option 1, Waste disposer - with air gap:
1. Remove the disposer knockout plug. Cut end of drain hose if
needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type clamp. If
the drain hose was cut, use a 11/2'' to 2" (3.8 to 5 cm) screw-type
clamp _.
3. Use a rubber hose connector _ with spring- or screw-type
clamps _ to connect air gap to disposer inlet.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed.
gap
Large
clamp
hose
Drain trap
4. Insert drain hose through hole
cut in cabinet to the front
center of opening where
drain connection will be
made.
_Parts available from local
plumbing supply stores.
6
Option 2, No waste disposer - with air gap:
1. Cut end of drain hose if it needs to be cut (do not cut ribbed
section).
2. Attach drain hose to air gap with large spring-type clamp. If
the drain hose was cut, use a 11/2'' to 2" (3.8 to 5 cm) screw-type
clamp _.
3. Use a rubber hose connector _ with spring or screw-type
clamps _ to connect air gap to waste tee.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed.
Rubber hose
connector
gap
Option 4, No waste disposer - no air gap:
1. Cut end of drain hose if it needs to be cut (do not cut ribbed
section).
2. Attach drain hose to waste tee with 11/2'' to 2" (3.8 to 5 cm)
screw-type clamp _.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed. It
is recommended that the drain hose be looped up and securely
fastened to the underside of the counter.
Drain hose -
cut here if needed
Screw-type
clamp
Large
clamp
Drain
Drain trap _._ hose
4. Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection
will be made.
_Parts available from local
plumbing supply stores.
Option 3, Waste disposer - no air gap:
1. Remove the disposer knockout plug. Do not cut end of drain
hose.
2.
Attach drain hose to disposer inlet with large spring-type
clamp.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed. It
is recommended that the drain hose be looped up and securely
fastened to the underside of the counter.
Large spring-type J
Drain hose
Drain trap_ _'" I--I
3.
Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection will
be made.
tee
Drain
3.
Insert drain hose through hole
cut in cabinet to the front
center of opening where drain
connection will be made.
_Parts available from local
plumbing supply stores.
Drain hose
hose
Electrical connection
Option 1, Direct wire method:
Helpful Tip: Wiring the dishwasher will be easier if you route
wire into the cabinet opening from the right side.
1. Drill a 3/4" (1.9 cm) hole in
right-hand cabinet side, rear
or floor. Preferred and
optional locations are shown.
2. Wood cabinet: Sand the hole
until smooth.
Metal cabinet: Cover hole
with grommet, (Part Number 302797 - not provided.)
3. Run wire into house wiring junction box.
4. Install a UL Listed/CSA Approved clamp connector (strain
relief) for flexible-type wire. If installing conduit, attach a UL
Listed/CSA Approved strain relief to the junction box.
5. Run other end of wire
through cabinet hole. Cable
must extend to the right
front of cabinet opening.
Option 2, Power supply cord method:
NOTE: A mating, 3 prong, ground-type wall receptacle is required
in a cabinet next to the dishwasher opening.
1. Drill a 11/2'' (3.8 cm)
hole in the cabinet
rear or side. Preferred
and optional
locations are shown.
2. Wood cabinet: Sand
the hole until smooth.
Metal cabinet: Cover
hole with grommet
Optional Preferred !
i.iS
(Part Number 302797) included with power supply cord kit.
Install the water line
Helpful Tip: Routing the water line through the left side of
cabinet opening will make water connection easier.
Drill a minimum 1/2" (1.3 cm) hole in the cabinet side, rear or
floor. Preferred and optional locations are shown.
2. Measure overall length
of copper tubing
required.
3. Attach copper tubing
to the water line with a
manual shutoff valve.
4.
Copper
tubing
Slowly feed copper
tubing through hole in
cabinet. Copper tubing will bend and kink easily, so be gentle.
The copper tubing should be far enough into the cabinet
opening to connect it to dishwasher inlet on the front left of the
dishwasher.
5. Turn water shutoff valve to '_ON" position. Flush water into a
shallow pan to get rid of particles that may clog the inlet valve.
6. Turn shutoff valve to '_OFF" position.
Install the drain hose
IMPORTANT: Always use a new drain hose.
1. Drill a 11/2'' (3.8 cm)
diameter hole in
cabinet wall or floor
on the side of the
opening closest to the
sink.
2. Connect drain hose to waste tee or waste disposer using one of
the following methods:
Option 1, Waste disposer - with air gap
Option 2, No waste disposer - with air gap
Option 3, Waste disposer - no air gap _
Option 4, No waste disposer - no air gap _
_An air gap is recommended.
Helpful Tip: To reduce the vibration of the hose, keep the hose
away from the floor and the edge of the hole where it passes
through the cabinet.
Option 1, Waste disposer - with air gap:
1. Remove the disposer knockout plug. Cut end of drain hose if it
needs to be cut (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type clamp. If
the drain hose was cut, use a 11/2'' to 2" (3.8 to 5 cm) screw-type
clamp _.
3. Use a rubber hose connector _ with spring or screw-type
clamps _ to connect air gap to disposer inlet.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed.
gap
Large
clamp
hose
Drain trap
4. Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection will
be made.
_Parts available from local
plumbing supply stores.
Option 2, No waste disposer - with air gap:
1. Cut end of drain hose if it needs to be cut (do not cut ribbed
section).
2. Attach drain hose to air gap with large spring-type clamp. If
the drain hose was cut, use a 11/2'' to 2" (3.8 to 5 cm) screw-type
clamp _.
3. Use a rubber hose connector _ with spring or screw-type
clamps _ to connect air gap to waste tee.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed.
Rubber hose
connector
gap
Large
clamp
Drain tra Drain
hose
4. Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection will
be made.
_Parts available from local
plumbing supply stores.
Option 3, Waste disposer - no air gap:
1. Remove the disposer knockout plug. Do not cut end of drain
hose.
2.
Attach drain hose to disposer inlet with large spring-type
clamp.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed. It
is recommended that the drain hose be looped up and securely
fastened to the underside of the counter.
Large spring-type J
_ Drain hose
Drain trap_ _ I--I
3.
Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection will
be made.
Option 4, No waste disposer - no air gap:
1. Cut end of drain hose if it needs to be cut (do not cut ribbed
section).
2. Attach drain hose to waste tee with 11/2'' to 2" (3.8 to 5 cm)
screw-type clamp _.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed. It
is recommended that the drain hose be looped up and securely
fastened to the underside of the counter.
Drain hose -
cut here if needed
Screw-type
clamp
tee
Drain
3. Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection will
be made.
_Parts available from local
plumbing supply stores.
hose
_,j _, '__j_:_ _, '_C__
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
2.
Helpful Tip: Put cardboard under dishwasher until it is installed
in cabinet opening. The cardboard will help avoid damage to
floor covering during installation.
Using 2 or more people, grasp the sides of dishwasher door
frame and put the dishwasher on its back, resting on top of the
corner posts.
Remove 2 screws attaching access panel and lower panel to
dishwasher using a 1/4" hex socket, nut driver or Phillips
screwdriver.
3. Removepanelsandsetpanelsasideonacoveredsurface.
4. Checkthatgroundingclipisattachedtothelowerpanel.
Lower
panel
clip
Slide nut and ferrule onto tubing.
Copper tubing only: Slide nut, then ferrule, about 1" (2.5 cm)
onto copper tubing.
NOTE: To avoid vibration during operation, route the water
supply line so that it does not touch the dishwasher base, frame
or motor.
6. Add 90 ° elbow fitting to the water supply line.
Connect the 3/8" compression fitting to the water supply line
prior to installing the unit into the cabinet opening. Attach such
that the 3/4" connection is facing upward.
Copper tubing only: Put the tubing into the 90 ° elbow fitting as
far as it will go (the copper tubing bends and kinks easily).
Slide the nut and ferrule forward and start the nut onto the
elbow threads. Flexible braided connection: Secure nut to
elbow using 5/8" open ended wrench or adjustable wrench.
NOTE: Do not use Teflon ®t tape with compression fittings.
Remove terminal box cover.
- If you are direct wiring: Install a UL Listed/CSA Approved
clamp connector to the terminal box. If using conduit, use a
UL Listed/CSA Approved strain relief.
- If you are installing a power supply cord kit, do so now,
following kit instructions. The power supply cord kit must be
UL Listed and marked for use with dishwashers (that is, Power
Supply Cord Kit Part Number 4317824).
. Terminal
I....................................................................................q_ box cover
_/ _" #_j_ CaBle clamp
connector
Dishwasher wires
Measure height of cabinet opening
from underside of countertop to
floor where dishwasher will be
installed (you need the lowest
point). Check chart for that height
opening. Put wheels in the required
position.
%
¢- 2
Wheel_ 3
Minimum
cutout height
333/4'' (85.7 cm)
33%" (86 cm)
34" (86.4 cm)
341¼'' (87 cm)
341/2'`(87.6 cm)
Wheel
position
remove
remove
1
2
3
iNumber of
turns on
front leg
all the
way up
all the
way up
10
Perforation
on Blanket
remove
keep
keep
keep
keep
Turn both front leveler legs to the same
height.
If the minimum cutout height is less than 34"
(86.4 cm), the rear wheels can be removed
for additional clearance. This will allow the
dishwasher to fit into a 337/8'' (86 cm) high
cutout, but the dishwasher will be more
difficult to move into position. If the wheels
Front leg
are removed, cover the floor when moving the dishwasher.
If the minimum cabinet opening height is 333/4" (85.7 cm), a
section in the insulation blanket can be removed by cutting
along the perforation.
t®Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.
10
Install the door handle (some Kenmore Elite models)
NOTES:
To ease installation, using two or more people, place the
dishwasher on its back.
To avoid scratching the front panel, place a soft cloth or towel
against the panel while installing the door handle.
Setscrews are preinstalled in the handle.
1. Remove the door handle and hardware bag containing the hex
key from the bubble pouch.
2. Place the handle on the mounting studs. The setscrews should
face down when installed correctly. If the handle is installed
upside down, proper installation will not be possible.
3. Push the door handle tightly against the door.
4. Insert the short end of the hex key into the setscrew and tighten
turn past snug. Setscrew will not be recessed into the handle.
5. Repeat Step 4 for other setscrew.
6. Keep the hex key with the Installation Instructions.
NOTE: The handle installation procedure should take less than
5 minutes.
Hole in panel f_/Mounting stud
Locating feature/- // 'd
// I
Door handle
Setscrew
Install the door handle (Kenmore PROTM models)
IMPORTANT: Do not scratch the front panel during this procedure.
1. Remove the door handle assembly from the upper dishrack of
the dishwasher.
2.
3.
Remove and discard the handle packaging. Be sure to retain
the handle installation instructions and mounting hardware.
Install the door
handle according to
the handle
installation
instructions provided
with the handle
assembly.
Install custom panel
Follow steps below:
A customer supplied panel must weigh no more than 16 Ibs (7.3 kg)
and must be made to specific dimensions. It is recommended that a
cabinetmaker cut the customer panel because of the precise
dimensions needed.
NOTES:
The handle for the custom panel is not included.
All mounting hardware supplied is for a 3¼,,(19.1 cm) thick
wood panel. If a thinner wood panel or materials other than
wood are used, it is the customer's responsibility to obtain the
proper length screws and adjust the pilot holes accordingly.
IMPORTANT: Use a moisture resistant sealer on both sides and all
edges of the panel to avoid damage from moisture.
Custom panel installation - Dishwashers with control panel on
the top.
235/8,,
(60 cm) "2929/32'' (76 cm)
¾" (19.1 ram)
_This dimension is for 4" (10.2 cm) toe kick. If the installation
needs a higher toe kick, adjust the height of the wood panel
accordingly. Not recommended for toe kicks greater than 6"
(15.2 cm).
2. Install the custom hardware handle(s) on the front of the
wooden panel inside dotted line.
IMPORTANT: If the handle is attached from the back of the custom
panel, the screw holes should be countersunk for the screw heads to
be flush with the panel. If the handle is attached to the front of the
custom panel, the screw lengths cannot exceed the panel thickness.
Top Of Panel
T_p_ delpanel
Oessusdepanneau
3.
Using the template provided attached it to the backside of the
custom panel with tape. Make sure that the center of the
template is aligned with the center of the wooden panel and
top of the template is aligned to the top face of the wooden
panel.
11
6. Attach the 4 plastic studs to the wooden panel using the 4 short
hex head (5,_61')screws provided.
NOTE: Do not drill deeper then 5/8" to keep from drilling through
panel. Pilot hole depths given are for 3A" thick panel.
4. Mark 4 pilot holes on the wooden panel using the template
provided. Predrill four pilot holes using a 3/32" drill bit. Use tape
to mark the drill bit to gauge hole depth. Drill pilot holes
approximately 5/8" into the custom panel.
Plastic studs attached
with 4 short screws
Visible side
7.
Wooden panel
assembly
ji
J
Align the studs on the custom wood panel to the keyhole slots
on the door assembly. Ensure that all 4 plastic studs are
engaged in the keyhole slots. Slide wood panel down until the
top surface of the wooden panel is flush with the top of the
door.
Align top
edges
5.
Check custom tape alignment with metal door slots; verify tape
is right-side up, and that the tape does not overhang the metal
door on the top, bottom or side interfaces. Remove the backing
from the custom tape by pulling straight down on the liner.
Align the custom tape to the keyhole slots on the metal door
(see image) and apply. Repeat steps for one side and then the
other.
NOTE: The adhesive on the tape is aggressive, so proper
alignment and attachment to the metal door needs to occur on
the first try.
8o
Drill through
these holes.
Customer-su
panel Remo_ 2 short screws
and replace with long
screws provided.
Open the door and align top edges. Predrill two pilot holes
using a 3/32"drill bit. Use tape to mark the drill bit to gauge hole
depth. Drill pilot holes approximately 11/2'' (12.7 mm) into the
top corners of the door using hole in liner as a guide.
Customer-supplied
panel
7
1¾" Screw
edges
)rill through
these holes
12
Install 2 long screws supplied in top corners to secure custom
wood panel in place.
Option 2, Dishwasher with Stainless Steel Tub Side
Attachment
(for marble, granite or other hard surface countertops)
NOTE: You must drill pilot holes in cabinet to avoid splitting the
wood before installing screws.
1. Remove the brackets from the parts package.
2. Break off the end of the bracket along the scored line.
Score
Nne
gn top
edges
Remove 2 short scre_ 3lied
and replace with long panel
screws provided.
10. Remove the short screws (3rd from top) on either side of the
inner door panel. Predrill 2 pilot holes using a 3/32" drill bit. Use
tape to mark the drill bit to gauge the hole depth. Drill pilot
holes approximately 11/2'' (12.7 mm) using the door liner hole as
a guide into the panel. Install the two remaining long screws.
Choose attachment option
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Using 2 or more people, stand the dishwasher up.
IMPORTANT: The dishwasher must be secured to the cabinet. There
are 2 brackets found in the parts bag. Attach the brackets to the
top of the dishwasher if the countertop is wood, laminate or
another similar surface. If your countertop is marble, granite or
another hard surface, install using Option 2.
Option 1, Countertop attachment
1. Remove the brackets from the package and place in the open
slots on the left- and right-hand top of the dishwasher collar as
shown.
Tabs must
2. Insert the bracket into the slot on the collar. Using a pair of
pliers, bend the tab down to secure the bracket in place.
Repeat this step for the other side.
4.
With another person holding the dishwasher to keep it from
tipping, open dishwasher door, and place towel over pump
assembly and spray arm of dishwasher. This will keep screws
from falling into pump area when securing dishwasher to
cabinet.
Push the plastic buttons out of the side of the tub.
NOTE: Save the buttons to cover the holes after dishwasher is
installed.
Plastic
button '
5.
N
Push bracket into slot on the side of dishwasher, and bend tab
in toward the side of the dishwasher so that it keeps the
bracket in place.
NOTE: Do not attach the dishwasher. This will be done later.
Bend
Option 3, Dishwasher with Plastic Tub Side Attachment
(for marble, granite or other hard surface countertops)
6. Order Mounting Bracket Kit Part Number 8212560.
Check door spring tension
1.
With another person holding the dishwasher to keep it from
tipping, open and close the door a few times. If the door closes
or falls open under its own weight, the door tension will need to
be adjusted.
2. To adjust the door spring tension, unhook the spring from the
rear leg of dishwasher.
3. With a 5_6" nut driver or hex socket, remove the screw from the
tensioner.
4.
The screw can be put into one of three holes 1, 2, 3 in front leg
of dishwasher. If the door closes by itself, move the tensioner to
a higher number hole and replace screw. When door is
unlatched, if it opens by itself, move tensioner to a lower
numbered hole and replace screw.
NOTE: Do not attach the dishwasher. This will be done later.
13
5.
Reattach door spring to rear leg. Tensioners on both sides of
dishwasher should be secured at same holes.
oner
-Sjw
1 2 3
Move dishwasher into cabinet opening
1.
2.
3.
4.
Using 2 or more people, stand the dishwasher up.
Grasp the sides of the dishwasher at the
edges of the door panel.
Tilt dishwasher backward on wheels and
move dishwasher close to cabinet
opening. Do not push on the front of the
panel or on the console -- they may
dent.
If dishwasher has a power supply cord, insert power supply
cord into hole cut into cabinet.
If using direct wire, check that it is on the right front side of
opening.
5. Check that water line is on the left side of opening and drain
hose is near the center of the hole in the cabinet.
6. Slowly move dishwasher completely into cabinet opening. Do
not kink or pinch copper tubing, drain hose, power supply cord
or direct wire between dishwasher and cabinet.
Helpful Tip: Once the dishwasher is in position, you may have
to support the front of the dishwasher by raising, lowering or
shimming front feet.
7. Remove cardboard from under dishwasher.
8. Using the precut slots in the insulation, attach the insulation to
the sides of the tub using the molded hooks on each side of the
tub.
NOTE: It is all right if dishwasher fits tightly into cabinet opening.
Do not remove insulation blanket -- the blanket reduces the sound
level.
Level the dishwasher
2.
Align front of dishwasher door panel with cabinet doors. You
may need to adjust alignment to be even with your cabinets.
Helpful Tip: Prop up one side of frame to hold dishwasher up
off floor when adjusting front legs.
With some installations, it may be easier to adjust the front leg
using the %6" hex head.
Check that leveling legs are firmly against the floor.
3.
4.
Place level against top front
opening of tub. Check that
dishwasher is level from side to
side. If dishwasher is not level,
adjust front legs up or down until
dishwasher is level.
Close and latch the door. Place the level against the front of
the dishwasher to check to see if it is vertically aligned.
5.
If needed, adjust rear leveling leg by using a Phillips
screwdriver to adjust the back of the unit. Turn the rear leveler
located on the front left hand side of the lower compartment
counterclockwise to raise the back of the unit.
Check "Electrical Requirements" section.
You need to."
have the correct electrical supply and recommended
grounding method.
If you are:
direct wiring, use Option 1
using a power supply cord, use Option 2
Option 1, Direct wire method
1. Route direct wire so that it does not touch dishwasher motors or
lower part of dishwasher tub.
14
2.
3.
4.
Pull direct wire through hole in terminal box.
Helpful Tip:
Select the proper size twist-on
connectors to connect your household
wiring to 16-gauge dishwasher wiring. .......
Insert wire ends into twist-on connector.
Do not pre-twist bare wire.
Twist connector.
Gently tug on wires to be sure both are secured.
Connect the wires as follows using twist-on connectors sized to
connect direct wire to 16-gauge dishwasher wire:
Power supply wire: Terminal box wire:
white--white
black--black
ground wire_e-_green ground connector
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord.
Failure to foflow these instructions can result in
death, fire, or electrical shock.
Form bare ground wire into a U-shaped hook. Wrap ground
wire hook clockwise around ground connector and under the
washer.
Securely tighten ground connector.
Ground wire Washer
Ground
connector
Option 2, Power supply cord method
1. Route the power supply cord so that it does not touch
dishwasher motors or lower part of dishwasher tub.
2. Pull the direct wire through hole in terminal box.
Helpful Tip:
Select the proper size twist-on
connectors to connect your household
wiring to 16-gauge dishwasher wiring. __,F',
Insert wire ends into UL Listed/CSA ,.,
Approved twist-on connector. Do not
pre-twist bare wire.
Twist connector.
Gently tug on wires to be sure both are
secured.
3. Connect the wires as follows using twist-on connectors sized to
connect power supply cord to 16-gauge dishwasher wire:
Power supply wire: Terminal box wire:
white--white
black--b Jack
ground wire--green ground connector
Electrical Shock Hazard
Electricafly ground dishwasher,
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord,
Failure to follow these instructions can result in
death, fire, or electrical shock.
6.
Ground wire
Tighten clamp connector or
conduit connector screws.
Reinstall terminal box cover
with wires inside terminal box.
The cover must be outside the box on
the left side.
8. Make sure no wires are pinched by
cove_
....... i
4. Form bare ground wire into a U-shaped hook. Wrap ground
wire hook clockwise around ground connector and under the
washer.
5. Securely tighten ground connector.
Ground wire Washer
Ground
connector
6.
Ground wire
Tighten clamp connector or conduit
connector screws.
ScrewL__
__ ....
15
7. 4. Place the smaller drain hose clamp onto the small end of the
drain hose.
Reinstall terminal box cover with
wires inside terminal box.
The cover must be outside the box on
the left side.
8. Make sure no wires are pinched by
cover.
9. Do not plug the dishwasher cord into the outlet until instructed
to do so.
10. Check that power supply cord does not touch dishwasher motor
or lower part of dishwasher tub.
2.
Tighten 90 ° elbow fitting to valve.
Be sure rubber washer is properly seated in fitting. Slide the 3/4"
fitting up to the valve and hand tighten to avoid unintentional
cross-threading. Hand tighten until the coupling is tight. Using
pliers, check the tightness of the coupling. An additional 1/4 to
1/2turn may be required to seal the rubber gasket.
NOTE: Do not overtighten. Damage to the coupling can result.
Check for leaks.
J[ . _'i_¸).....
Place paper towel under 90 ° elbow fitting. Turn on water
supply and check for leaks. If leak occurs, repeat previous step.
2.
3.
To help minimize vibration,
route drain hose to avoid
contact with motor, door
springs, water line, cabinet,
flooring or the edge of the
hole where it passes
through the cabinet.
Do not remove drain loop
from side of dishwasher.
Place pan under end of
drain hose. Pan will collect
J,,
i i i i
l/
_'\ i \ J
_" -- _----- Drain ] /
any water in drain hose.
Hose clamp
/
5.
6.
Push the drain hose into the connector up to the stop on the
drain hose.
Connector Stop
Use pliers to open clamp and slide clamp onto connector
between stops on connector as shown.
Hose clamp
Stops
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts,
1. If you have not already done so, open dishwasher door and
place towel over pump assembly and spray arm of dishwasher.
This will keep screws from falling into pump area if you
unintentionally drop them when securing dishwasher to
countertop.
2. Check that dishwasher is still level and centered side to side in
the opening.
3. Secure dishwasher to countertop or sides of cabinet with 2,
#10 x 1/2" Phillips-head screws. The dishwasher must be secured
to keep it from tipping when door is opened.
4.
I[
I
OR
Screw to countertop Screw to
side cabinet
NOTE: You must drill pilot holes in cabinet to avoid splitting
the wood before installing screws.
Open door about 3" (7.6 cm) and check that space between
inner door and tub is equal on both sides. If spacing is not
equal, loosen bracket screws and shift tub. Tighten bracket
screws.
16
5.
If using a countertop attachment to secure dishwasher, check
that top of door does not contact screws, brackets, or
countertop. If it does, dishwasher must be lowered and re-
leveled.
6. If securing with a side attachment, check that sides of door do
not rub against the screw heads. If they do, dishwasher must be
re-centered.
7. Remove towel from dishwasher.
8. Reinstall the lower dish rack.
Complete installation
1.
2.
Check that grounding clip is attached to the lower panel.
Place the lower panel behind the access panel. Some models
have insulation on the access panel which must fall behind the
insulation on the lower panel.
Grounding
clip
3. Hold the two panels together and place them against
dishwasher leg.
4. Reinstall the screws through the holes in the access panel and
the slots in the lower panel. Install right side screw first.
Direct wire method:
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Power supply cord method:
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result
in death, fire, or electrical shock.
7. Reconnect power or plug in dishwasher.
J
_z
5. Check that the lower edge of the lower panel contacts the
floor.
6. Tighten the screws.
17
Check operation
1. Read the Use and Care Guide that came with your dishwasher.
2. Check that all parts have been installed and no steps were
skipped.
3. Check that you have all the tools you used.
4. Start dishwasher and allow it to complete the shortest wash
cycle. After the first 2 minutes, unlatch door, wait 5 seconds,
then open door.
5. Check to see that there is water in the bottom of the dishwasher
tub. Check that dishwasher is working properly.
6. If the dishwasher is not working properly, disconnect power or
unplug dishwasher and see "If dishwasher does not operate"
section.
If dishwasher does not operate
First try the solutions suggested here to possibly avoid the cost of a
service call.
Has the circuit breaker tripped or the house fuse blown?
Isthe door closed tightly and latched?
Has the cycle been set correctly to start the dishwasher?
Isthe water turned on?
If none of these work, call 1-800-4-MY-HOME.
18
INDICE
SEGURIDAD DE LA LAVAVAJILLAS ............................................ 19
REQUISITOS DE INSTALACI6N ................................................. 20
Herramientas y piezas ......................................................................... 20
Requisitos de ubicaci6n ....................................................................... 20
Requisitos de desagOe ......................................................................... 22
Requisitos del suministro de agua ..................................................... 22
Requisitos el&ctricos ............................................................................. 22
INSTRUCCIONES DE INSTALACION .......................................... 23
Prepare la abertura del armario usando
las conexiones de servicio existentes ................................................ 23
Prepare la abertura del armario donde
no existen conexiones de servicio ...................................................... 24
Prepare la lavavajillas ......................................................................... 26
Conexi6n el&ctrica ................................................................................ 32
Conexi6n al suministro de agua ......................................................... 33
Conexi6n al desagOe ............................................................................ 34
Asegure la lavavajillas en la abertura del armario ....................... 34
SEGURIDAD DE LA LAVAVAJILLAS
Su seguridad y la seguridad de los demos es muy importante.
Hemos incluJdo muchos mensajes Jmportantes de seguridad en este manual yen su electrodomestico. Lea y obedezca siempre
todos los mensajes de segurJdad.
Este es el sfmbolo de advertencia de seguridad.
Este simbolo le llama la atenci6n sobre peligros potenciales que pueden ocasionar la muerte o una lesi6n a
usted y a los dem_.s.
Todos los mensajes de seguridad iran a continuaci6n del sfmbolo de advertencia de seguridad y de la palabra
"PELIGRO" o "ADVERTENCIA". Estas palabras significan:
Si no sigue las instrucciones de inmediato, usted puede
morir o sufrir una lesi6n grave.
Si no sigue las instrucciones, usted puede morir o sufrir
una lesion grave.
Todos los mensajes de seguridad le diran el peligro potencJal, le diran c6mo reducir las posibJlidades de sufrJr una lesi6n y Io que
puede suceder si no se siguen las instrucciones.
Pe|igro de Vuelco
No use la lavavajillas antes de estar completarnente
instalada.
No se apoye en la puerta abierta.
No seguir estas instrucciones puede ocasionar heridas
serias o cortaduras.
Usted necesita=
Abrir lentamente la puerta de la lavavajillas mientras alguien
sujeta la parte trasera de la lavavajillas. Quite los materiales
de env_o, la manguera de desagge y la canasta inferior. Cierre
la puerta de la lavavajillas hasta que quede asegurada.
Cumplir con todos los c6digos y reglamentos vigentes.
Instalar la lavavajillas seg0n se especifica en estas
instrucciones.
La instalaci6n debe ser hecha por un t&cnico de servicio
calificado. La lavavajillas debe instalarse de acuerdo con
todos los c6digos y reglamentos el&ctricos y de plomer_a
nacionales y locales.
19
REQUISITOSDE INSTALACION
Retina las herramientas y piezas necesarias antes de comenzar la
instalaci6n.
Todas las instalaciones
Herramientas necesarias-
Pinzas
Destornillador Phillips
Llaves de tuercas o
casquillos hexagonales de
5_6" y 1/4"
Cinta de medir o regla
Llave ajustable de 10" que
se abra a 11/8'' (2,9 cm)
Destornillador de hoja plana
Cuchillo de uso general
2 conectores de empalme
retorcido para alambre
que tengan el tama_o
adecuado para conectar el
cableado de su hogar al
cableado calibre 16 de la
lavavajillas
Adem6s, para nuevas instalaciones
Herramientas necesarias:
Taladro inal6mbrico con
brocas de sierra perforadora
de 1/2", 3_" y 11/2,,
Cortatubos peque_o
Pelacables
Abrazadera tipo tornillo de
11/2'' a 2" si se ha de
conectar al tubo de
desperdicios
Nivel peque_o
Linterna
Recipiente poco profundo
Llave ajustable de %"
Toalla de ba_o
Bloque de madera
Piezas necesarias:
Conector a compresi6n de
3/8" x conector de
manguera de 3/4". P6ngase
en contacto con la tienda
local de Sears para
comprar el Juego N °
11000.
Piezas necesarias:
Tuberia de cobre (se
recomienda de 3/8") o Ifnea
de Ilenado flexible de
acero inoxidable
Conector de abrazadera o
conector de conductos que
quepa en un orificio de 7/8"
(2,2 cm) de di6metro
Piezas provistas
A. 2 abrazaderas para la manguera de desagOe: 1grande y 1peque_a
B. 2 tornillos Phillips No. 10 x 1/2"
C. Manguera de desagOe
D. En algunos modelos Kenmore Elite, un cart6n conteniendo una
manija, Ilave hexagonal y 3 tornillos opresores
E. En los modelos Kenmore PRO TM, juego con manija, 2 tornillos de
montaje de 5/8", 2 placas de soporte y una hoja de instrucciones
para instalar la manija.
F. 2 soportes de montaje (superior) para el mostrador
G. 2 Cinta personalizada
B
G
Aseg6rese de que todas las piezas est&n incluidas. Si no Io est6n,
Ilame al 1-800-4-MY-HOME.
Vea la lista de piezas que viene por separado para ver qu&
accesorios est6n disponibles para su lavavajillas.
Se incluye en el juego:
4 taquetes de pl6stico (sujetados unos a los otros con
correderas)
4 tornillos cortos (tornillo de cabeza hexagonal 10-16)
4 tornillos largos (tornillos de cabeza Torx _t 8-18)
1 plantilla (ubicada adentro de la bolsa del Manual de uso y
cuidado para el ensamblaje)
1 hoja de instrucciones (ubicada adentro de la bolsa del
Manual de uso y cuidado para el ensamblaje)
NOTA: Los tornillos provistos se utilizan 6nicamente para un panel
de madera de 3/_" de grosor. Si el panel de madera tiene un
grosor menor a 3¼", el cliente debe adquirir los tornillos en su
Iocalidad.
No instale tuberias de agua o desagOe ni cableado el&ctrico donde
puedan interferir o hacer contacto con el motor o las patas de la
lavavajillas.
El lugar donde se instalar6 la lavavajillas debe permitir un espacio
libre entre el motor y el piso. El motor no debe tocar el piso.
No instale la lavavajillas sobre piso alfombrado.
Proteja la lavavajillas y las lineas de agua que van a la lavavajillas
contra el congelamiento. La garantia no cubre daBos por
congelaci6n.
Puede obtener un juego de panel lateral con el distribuidor para
instalar su lavavajillas en el extremo del armario.
Su distribuidor tiene un accesorio que funciona como barrera
contra la humedad (Pieza N ° 4396277) para ser instalado debajo
del mostrador. Este puede obtenerse tambi&n Ilamando al
1-800-4-MY-HOME.
Revise el lugar donde instalar6 la lavavajillas. El lugar debe
proveer:
F6cil acceso a instalaciones de agua, electricidad y desagOe.
Facilidad para cargar y descargar la lavavajillas. Los rincones
deben tener un espacio libre minimo de 2" (5,1 cm) entre el
costado de la puerta de la lavavajillas y la pared o el armario.
Una abertura cuadrada para que la lavavajillas funcione y se
vea bien.
La parte frontal del armario que sea perpendicular al piso.
Piso nivelado. (Si el piso en la parte delantera de la abertura
no est6 nivelado con el piso en la parte trasera de la abertura,
puede usar cu_as para nivelar la lavavajillas.)
NOTA: Las cu_as deben adherirse con firmeza al piso para evitar
que se muevan cuando se est& usando la lavavajillas.
Siva a dejar la lavavajillas sin uso por cierto tiempo o en un lugar
donde pudiera congelarse, haga que un miembro del personal de
servicio autorizado la prepare para el invierno.
Aseg6rese de que la tuberia, los cables el&ctricos y la manguera de
desagOe est&n en el 6rea sombreada que se muestra en la secci6n
"Dimensiones de corte".
Consejo Otil: Si el piso de la abertura donde colocar6 la
lavavajillas no es parejo (por ejemplo: piso con Iosetas s61o
hasta cierta parte de la abertura), deber6 ser exacto para
tomar las medidas y nivelar la lavavajillas.
_®TORXes unamarca registrada de Saturn Fasteners,Inc.
2O
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Kenmore 66512776K312 Guide d'installation

Taper
Guide d'installation
Ce manuel convient également à