Ground Zero NUCLEAR GZNA 2800XII Le manuel du propriétaire
- Catégorie
- Amplificateurs audio de voiture
- Taper
- Le manuel du propriétaire
Amplifier
Owner’s Manual
NUCLEAR
GZNA 2800XII
2
PLEASE READ BEFORE INSTALLATION
Thank you for selecting a Ground Zero amplifier.
We are providing a helpful hints list which should keep you from experiencing
unnecessary shut down.
Have fun with this high quality Uranium product.
Features
• 1 Ohm stable stereo (0,5 Ohm stable at music operation)
• 2 Ohm stable bridged (1 Ohm stable at music operation)
• Dual Mosfet power supply
• SMD Technology
• Power & Protection indicator
• Variable 12dB Bass Boost
• High pass filter (Subsonic filter) with 1/10 switch variable to 4000Hz
• Low pass filter with 1/10 switch variable to 4000Hz
• Variable phase shift 0-180°
• Adjustable input sensitivity
• Soft delayed remote turn- on
• Remote control
• Thermal / Short / Overload protection
3
Nuclear amplifier
Due to their state- of- the- art technology and high efficiency, these amplifiers help your system to provide an
impressive sound experience. The modern circuit technology of the power supply and the signal processing allows
achieving maximum performance levels from the provided power.
Tools and materials you need
• Screwdriver
• Electric drill, 3 mm / 0.12” carbide drill bit
• Mounting screws
• Power wire min. 35 mm² / 2 AWG
• Ground wire min. 35 mm² / 2 AWG
• Speaker wire min. 2 x 4 mm² / 11 AWG
Please note!
• As a precaution it is advisable to disconnect the vehicle’s battery before making connection
to the +12 Volts supply wiring (see owner’s manual of your car for further information).
• Please use great caution drilling your trunk. Your gas tank and brake lines can be damaged by
puncturing with your drill bit – this could cause damage or failure of your cars operating systems.
• Never pass wires over sharp angles. It is recommended to buffer the power supply of the amplifier
with an additional battery (GZBP 12.2500 or GZBP 12.3500) to guarantee a stable operation voltage.
WARNING !
High powered audio systems in a vehicle are capable of generating "Live Concert" levels of sound pressure.
Continued exposure to excessively high volume sound levels may cause hearing loss or damage. Also, operation
of a motor vehicle while listening to audio equipment at high volume levels may impair your ability to hear
external sounds such as; horns, warning signals, or emergency vehicles, thus constituting to a potential traffic
hazard. In the interest of safety, Consumer Electronics recommends listening at lower volume levels while driving.
4
Planning your system
Before beginning the installation, consider the following:
a. If you plan to expand your system by adding other components sometime in the future, ensure
adequate space is left, and cooling requirements are met.
b. If your radio / source is equipped with pre-amp outputs, it is possible to utilize them to drive the
amplifier and connecting (amplifier) to the 2 rear speakers.
Mounting your amplifier
a. Select a suitable location that is convenient for mounting, is accessible for wiring
and has ample room for air circulation and cooling.
b. Use the amplifier as a template to mark the mounting holes, remove the amplifier and drill 4 holes.
Then mount the amplifier with the mounting screws.
Warning
Chose a mounting position where all eclectic wires are protected from being damaged by sharp edges, heat or
other conditions. +12Volt DC electrical connections must be fused on the battery side. Make sure your radio and
all other devices will be turned off while connection your system.
This amplifier has now internal fuse. Therefore it is absolutely necessary to connect the ANL- fuseholder (included
in delivery) with its 200 A fuse. The cable length between amplifier and fuseholder must not be longer than max
20 cm / 7.9”. Please see the connection diagram on the following side for correct wiring.
7
Controls and functions
1 Speaker terminals For connection of the speakers
2 Power terminals GND -> Ground connection
REM -> Remote antenna terminal
BATT -> +12 Volt
3 Satus indication BLUE
–
OK
RED – Error
4 Cinch inputs Terminal for connection of the RCA wires.
To avoid failure, please use high quality RCA wires.
5 Input level controlle
r
With this controller you can adjust the input sensi
t
ivity.
6 Bass boost controlle
r
For adjusting of the bass boost level in the range from 0 to +12 dB.
7 Bass frequency controller For adjusting of the bass boost frequency in a range
from 30Hz to 80Hz.
8 High pass controller
(Subsonic)
Set the filter switch to „HIGH“ position.
Adjust the variable Highpass crossover frequency to the desired
frequency using the controller. All frequency between 5Hz and 4000Hz
will be reproduced.
HPF X1/X10 Switch:
X1 – Adjustment range 5Hz – 400Hz
X10 – Adjustment range 50Hz – 4000Hz
9 Mode switch
A
djust the crossover for the chosen utilization.
LOW (Bandpass) – Only bass frequencies (below 30Hz - 4000Hz) will
be reproduced. In this adjustment the Highpass (Subsonic) is also
activated.
FULL – All frequencies will be reproduced.
HIGH (Subsonic) – Only middle and high frequencies
(over 5Hz – 4000Hz) will be reproduced.
10 Low pass controller
For subwoofer and Kickwoofer operation -
Only frequencies from 30Hz to 4000Hz will be reproduced (depending
on the lowpass filter controller position). Set the filter switch to „LOW“
position. Adjust the variable Lowpass frequency to the desired
frequency using the controller.
LPF X1/X10 Switch:
X1 – Adjustment range 30Hz – 400Hz
X10 – Adjustment range 300Hz – 4000Hz
11 Phase shift controller This controller allows you to fit the subwoofer channel in-phase to the
front system.
12 Remote control input For connection of the bass remote control.
Turning on the amplifier
The amplifier automatically turns on a few seconds after you turn on your radio.
Note: Your amplifier temporarily shuts down if it gets too hot, then restarts automatically once it cools
(At about 80° / 176° F).
Adjusting the audio level
1. LEVEL (Min/Max): Turn fully counter- clockwise to MIN position
2. Turn the auto sound system's volume control to about two-third of its full range.
3. Adjust LEVEL to a comfortable listening level.
8
Connecting the speaker
9
Trimode operation
Connecting the speaker for trimode operation - notes
TRI MODE operation output allows a subwoofer to be operated in mono mode while the main speakers are
playing in stereo. Leave the crossover switch on “Full” position.
Use 100 volt, non-polar capacitors for a high pass crossover to filter out low frequencies and Air- core or
Ferrit- ore coils with a minimum diameter of 1 mm / 0.039” for the lowpass crossover to filter out high
frequencies.
The capacitor and inductor values as written in the below table. The front and rear channels of this amplifier get
this capability. Only the rear left and right channels are shown on the following pictures.
Values for 6dB passive crossover
Frequency Inductor Capacitor
80 Hz 7,5 mH 470 uF
100 Hz 6,5 mH 330 uF
120 Hz 5,5 mH 370 uF
150 Hz 4 mH 220 uF
10
Specifications
Model GZNA 2800XII
RMS Power @ 4 Ω
CEA Standard CEA-2006-A
2 x 430W (1% THD+N)
2 x 520W (10% THD+N)
RMS Power @ 2 Ω
CEA Standard CEA-2006-A
2 x 800W (1% THD+N)
2 x 950W (10% THD+N)
RMS Power @ 1 Ω
CEA Standard CEA-2006-A
2 x 1200W (1% THD+N)
2 x 1400W (10% THD+N)
RMS Power @ 4Ω bridged
CEA Standard CEA-2006-A
1 x 1600W (1% THD+N)
1 x 1900W (10% THD+N)
RMS Power @ 2Ω bridged
CEA Standard CEA-2006-A
1 x 2400W (1% THD+N)
1 x 2800W (10% THD+N)
Damping factor > 150
Signal to noise Ratio > 90 dB
Lowpass 30 – 400 Hz / 300 – 4000 Hz
Highpass 5 – 400 Hz / 50 – 4000 Hz
Bandpass 5 Hz – 4000 Hz
Subsonic filter 5 Hz – 4000 Hz
Bass boost 0 ~ +12 dB
Bass boost frequency 30 Hz ~ 80 Hz
Phase shift 0 – 180°
Frequency response 10 Hz – 38 KHz
(± 1 dB)
Efficiency @ 4 Ω ~ 80 %
Input sensitivity 200 mV – 9 V
(± 5%)
Channel separation 50 dB
THD < 0,10 %
Bass remote 9
At Lowpass- operation
Fuse External ANL-fuse 200A
(included in delivery)
Dimensions
W x H x L mm 305 x 62 x 600
Dimensions
W x H x L inch 12 x 2.44 x 23.62“
11
Trouble shooting guide
Symptoms Check Points Cure
No sound
Is the POWER LED illuminated?
Check fuses in amplifier.
Be sure remote lead is connected.
Check signal leads.
Check again control.
Check tuner/deck volume level.
Is the diagnostic LED illuminated? Check for speaker short or
amplifier overheating
Amp not switching on
No power to the amplifier Check power wire or connections
No power to remote wire with
receiver on Check connections to radio
No sound in one channel
Check speaker leads Inspect for short circuit or an open
connection
Check audio leads
Reverse left and right RCA inputs
to determine if it is occurring
before the amp
Amp turning off at medium /
high volume Check speaker loa impedance
Be sure proper speaker load
impedance recommendations are
observed
(If you use an ohm meter to
check speaker resistance, please
remember that DC resistance and
AC impedance may not be the
same.)
Protection LED is on
Temperature shut down Turn radio volume down
Speaker wires short Separate speaker wires and
insulate
12
Die Gewährleistung entspricht der gesetzlichen Regelung. Eine Rücksendung kann nur nach
vorheriger Absprache und in der Originalverpackung erfolgen. Bitte unbedingt einen maschinell
erstellten Kaufbeleg und eine Fehlerbeschreibung beilegen. Von der Gewährleistung
ausgeschlossen sind Defekte, die durch Überlastung, unsachgemäße Behandlung oder bei
Teilnahme an Wettbewerben entstanden sind.
Limited warranty - defective products must be returned in original packaging - please add a copy
of the original purchasing invoice showing the purchasing date and a detailed description of the
failure. Failure caused by overload, misuse or by using the product for competition purpose are
not covered by the warranty.
De Garantie bepalingen van alle door ground zero geleverde producten is volgens wettelijke
bepalingen geregeld, Een retourzending kan alleen na duidelijke afspraak en in de originele
verpakking plaatsvinden.SVP een aankoopbon en een duidelijke storingsomschrijving
bijvoegen.Van garantie uitgesloten zijn defecten door overbelasting, onkundig gebruik, of door
deelname aan wedstrijden (SPL) ontstaan zijn.
La garantie est conforme aux droits légaux. Un retour du produit défectueux doit être dans son
emballage d'origine sur présentation du reçu ou de la facture indiquant la description du
defaut.La présente Garantie n'est pas applicable lorsque le produit a été endommagé en raison:
Mauvaise alimentation, Trop de puissance (HP,Subwoofer) Accident, Installation ou Utilisation non
conforme aux normes Technique (Concours SPL etc).
GROUND ZERO GmbH
Erlenweg 25; D - 85658 Egmating, Germany
Tel. +49 (0)8095/873 830 Fax -8310
www.ground-zero-audio.com
Wir behalten uns das Recht vor, zukünftig nötige Änderungen oder Verbesserungen an dem
Produkt vorzunehmen ohne den Kunden darüber zu informieren.
We reserve the right to make needed change or improvement to the product without informing
customer about this in advance.
Wij behouden ons het recht om de nodige veranderingen of verbeteringen aan het product door
te voeren zonder de klant hierover te informeren.
Nous nous réservons le droit d'entreprendre à l'avenir nécessairement des modifications ou des
améliorations au produit sans informer le client.
-
1
-
2
-
3
-
4
-
5
-
6
Ground Zero NUCLEAR GZNA 2800XII Le manuel du propriétaire
- Catégorie
- Amplificateurs audio de voiture
- Taper
- Le manuel du propriétaire
