Movon OSmart Witness Adas Camera Mode d'emploi
- Taper
- Mode d'emploi
Copyright ⓒ MOVON Test Lab Co., Ltd. All rights Reserved.
User Manual
User Manual
Version 1.0
1. About Product
2. Product Functions
1) Automatic Booting
Once the AP1 has been wired to your OBD-II port or vehicle power source the AP1 will
be boot up automatically. It will take around 55sec. for the unit to be ready to operate.
2) ADAS Functions
FCW
Forward collision warning system monitors a vehicle's speed, the
speed of the vehicle in front of it, and the distance between the
vehicles, so that it can provide a warning to the driver if the
vehicles get too close, it helps driver to avoid a crash.
FVSA
Notifies the driver if the front vehicle starts to move forward from
0 speed (complete stopped status) and the driver’s vehicle is not
moving within 2 seconds.
FPW
Notifies the driver when the front vehicle is within detection range.
Detection range can be setup on a scale of 1 to 3 (Active from 0 ~
30km/h) during the calibration. As the level gets higher, you will
hear the warning sound earlier.
3) Video Recording
Continuous Record
This is the default mode for recording. In this setting the unit will begin recording after
boot up and record the entire time the unit is powered on. The resolution and frame
rates can be set as per your requirements.
Event Record
The unit will record when triggered by impact, FCW warning situation or a push of the
“Record” button. You can set the record time during the calibration setting mode.
Dual Record
The continuous record file will be stored on “Normal Folder” and the Event record will be
stored on the “Event” folder on SD card.
Drive Data
The DRV file will be recorded during the driving even if there are no events or video. The
DRV file consist of GPS and G-sensor data. The DRV file overwrites the oldest data.
The DRV files will be made every 1~10 minutes.
Time and date
This information will be provided by GPS satellite’s automatically.
SD Memory card format
Please format(erase) the SD card using the server program.
4) Hotspot
Please press the multi-function button for 3 seconds (Long Press).
5) Volume control
Please press the volume button. The volume level is 5 steps and it make loop.
3. LED and Audio Guide
Status/Step
LED
Sound
1
2
3
3 color
Green
Blue
Start-up /
On&Off
Booting
step1
Before trouble
shooting
Flashing
(Orange)
Off
Off
Booting
step2
Trouble
shooting
Flashing
(Orange)
Flashing
Off
Booting
step3
Initializing
modem
Flashing
(Orange)
Flashing
Flashing
Booting finished
On
On
On
Booting
Melody
Power ON
Normal : On
(Green)
Initial state : On
(Orange)
Off
Off
Power Off / finished
Off
Off
Off
Recording
Continuous
Record
Recording
-
On
-
Event
Record
G-Sensor
Recording
-
On
-
FCW
Recording
-
On
-
User
Recording
-
On
-
Record
Error
SD Error, No
SD, Write Fail
-
3 times Fast
flashing every
10 secs.
-
No Record
Recording Off
-
Off
-
SD Format
-
Fast flashing
until the
process finish
-
ADAS
FCW Warning
-
-
-
Warning
sounds
FPW Warning
-
-
-
Warning
sounds
FVSA Alert
-
-
-
Warning
sounds
Communic
ation
3G/4G Network Device
Ready
-
-
2times
flashing every
10sec.
3G/4G Network Device
Connected
-
-
ON
3G/4G Network Device
Error, SIM Error
-
-
3 times Fast
flashing every
10 secs.
Data Network Connection
Error
-
-
3 times Slow
flashing every
10 secs.
Status
G-Sensor Calibration
Slow flashing
until the
calibration
finished
(Orange)
-
-
Beep
sounds
Setting Mode
(ADAS, Recording etc.)
Red/Green LED
cross flashing
during until the
setting mode
finished
Setting
Sounds
Firmware Upgrade
Fast flashing
until the firmware
update finished
(Green)
-
-
GPS Error
3 times Fast
flashing every 10
secs. (Orange)
-
-
Camera Error
ON (Red)
-
-
CAN Error
3 times Fast
flashing every 10
secs. (Green)
-
-
*flashing (On and off): 500msec on and 500msec off
*Fast flashing (On and off): 100msec on and 100msec off
*Slow flashing (On and off): 1,000msec on and 1,000msec off
4. Technical Support & Warranty
1) Technical Support
For technical Support, please contact your local distributor or visit
support.smartwitness.com
2) Limited Warranty
This product is supplied with 2 years warranty. The Warranty excludes products that
have been misused (including accidental damage) and damage caused by normal wear
and tear. In the unlikely event that you encounter a problem with this product, it should
be returned to the place of purchase.
FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device , pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiated radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for compliance
could void the user‘s authority to operate the equipment.
RF Exposure Information
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to
the antenna shall not be less than 20cm (8 inches) during normal operation.
ISED Notice
This device complies with Innovation, Science and Economic Development Canada license-exempt
RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
ISED Radiation Exposure Statement
This device complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment.
In order to avoid the possibility of exceeding the ISED radio frequency exposure limits, human proximity
to the antenna shall not be less than 20cm (8 inches) during normal operation.
Cet appareil est conforme aux limites d'exposition aux rayonnements de la CNR-102 définies pour un
environnement non contrôlé. Afin d'éviter la possibilité de dépasser les limites d'exposition aux
fréquences radio de la CNR-102, la proximité humaine à l'antenne ne doit pas être inférieure à 20 cm
(8 pouces) pendant le fonctionnement normal.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
