Hunter Fan 82022 Le manuel du propriétaire

Bath Ventilator with Light

Owner’s Manual

La Strada

42929-01

20101026

Model

82022

English

Español

Página 22

Français

Page 43

2

42929-01 10/26/2010

DISCONNECT

ELECTRIC

POWER SUPPLY

AND LOCK OUT

SERVICE PANEL

BEFORE

SERVICING UNIT

W A R N I N G

TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, OBSERVE THE FOLLOWING:

1. For general ventilating use only. Do not use for

ventilating hazardous or explosive materials.

2. To avoid motor bearing damage and noisy/unbal-

anced impellers, keep drywall spray, construction

dust, etc. off power unit.

3. DO NOT install this product in a wall. This prod-

uct is designed for installation in ceilings up to a

12/12 pitch (45 degrees). Ductwork must point

upward.

4. Please read specification label on product for fur-

ther information and requirements.

PREVENTATIVE MAINTENANCE

A clean fan provides better service. Disconnect the power supply and clean the fan as listed below.

TO CLEAN GRILLE:

Use a mild detergent, such as dishwashing liquid, and a soft cloth. DO NOT use abrasive cloths, steel wool pads

or scouring powders.

TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle. To remove motor plate, find the single tab on the

motor plate (located next to the receptacle). Push up rear motor plate tab while pushing out on the side of the

housing or insert a screwdriver into the slot in the housing (next to tab) and twist screwdriver. Gently vacuum

fan, motor and interior of housing.

METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER.

MAINTENANCE

The motor is permanently lubricated and never needs oiling. If the motor bearings are making excessive or

unusual noises, replace the motor with the exact service motor. You should replace the impeller at the same

time.

C A U T I O N

W A R N I N G

1. Use this unit only in a manner intended by the manu-

facturer. If you have questions, contact the manufac-

turer at the phone number or address listed in the

warranty.

2. Before installing, servicing, or cleaning the unit,

disconnect the power by turning o the circuit break-

ers to the outlet box and associated wall switch loca-

tion. If you cannot lock the circuit breakers in the o

position, securely attach a prominent warning device,

such as a tag, to the service panel.

3. Installation work and electrical wiring must be done

by qualified person(s) in accordance with all applicable

codes and standards, including fire-rated construction

codes and standards.

4. When cutting or drilling into wall(s) or ceiling, do not

damage electrical wiring or other hidden utilities.

5. Ducted fans must always be vented to the outdoors.

Keep ducting as short and as straight as possible.

6. Acceptable for use over a bathtub or shower when

connected to a GFCI protected branch circuit.

7. Install fan at least 5 feet (1.52 m) above the floor.

8. Never place a switch where it can be reached from a

tub or shower.

9. This unit must be grounded.

E

F

G

H

I

J

M

N

O

x4

*

NOTE:

Strain relief cable connector

must be installed. Not

Included.

A

B

C

95044-01-096

95029-01-000

77481-01-000

03242-01-232

95491-06-000

74508-03-133

97258-01-000

65219-01-000

77521-01-000

75184-01-092

97260-01-000

P

76079-02-481

Extra Screws

x2

D

K

L

3/8” Cable Connector

3

1

Turn off the power source.

Tools Needed. (Not supplied.)

Estimated assembly time: 30 to 60 minutes

Before Installation

Check all the parts.

If damaged, call

1-888-830-1326

for replacements.

2

F

J

Loosen screws.

NOTE: Remove all packing materials before installation.

42929-01 10/26/2010

5

4

7

H

8

G

Remove the motor/blower from the housing.

4

3

I

F

Remove the pre-loaded screw tip covers.

Remove the wiring cover screw.

6

Back out the pre-loaded screw tips until flush

with the side of the housing.

Remove the wiring cover.

Remove packing material.

42929-01 10/26/2010

9

F

Pop out the first wiring access slug. Use second if needed. Insert the strain relief (not included) into the housing and

secure with washer.

Position the correct depth mark at the bottom edge of the

joist based on the thickness of your sheetrock.

New Construction - attaching to joist

5

10

B

C

Choose Installation Option

For New Construction - attaching to joist go to step A11, page 5

For New Construction - suspended between joists go to step B11, page 8

For Existing Construction - accessible from above go to step C11, page 11

For Existing Construction - accessible only from below go to step D11, page15

A11

F

5/8

1/2

5/8

1/2

A12

Screw pre-loaded screws into joist or framing.

42929-01 10/26/2010

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

A14

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

A13

Route wires through the strain relief.

Connect wires as shown.

0

A16

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may need

to be purchased.

6

A15

F

H

Install the wiring cover plate. Make sure all

wiring connections are inside the box or under

the wiring cover plate.

42929-01 10/26/2010

A19

J

Secure the motor by tightening the 2 screws.

A20

Turn on the power source.

7

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

0000

A17

Reinstall the motor by inserting the tabs and pushing up

into position. Make sure the wires are not pinched

between the motor and the housing.

0000

I

A18

ON

OFF

A21

Test the motor. If the motor does not run, check the plug

connection.

A22

E1

Go to step

on page 17

to attach grille.

42929-01 10/26/2010

Slide the mounting rails into brackets.

Mark position of screws by using holes as a template.

Insert screws, leaving space between the screw

head and the joist. Screws are not provided.

New Construction – suspended between joists

8

B11

E

F

5/8

1/2

5/8

1/2

B12

1/8” bit

B14

B15

F

B13

Position the correct depth mark at the bottom edge of

the joist based on the thickness of your sheetrock.

Drill a hole in the center of each outline.

Attach the rails onto the screws.

B16

42929-01 10/26/2010

Tighten screws. Route wires through the strain relief.

Connect wires as shown.

9

B17

B18

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

B19

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

B21

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may need

to be purchased.

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under the

wiring cover plate.

G

H

B20

42929-01 10/26/2010

10

B27

E1

Go to step

on page 17

to attach grille.

B22

I

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

I

B23

Reinstall the motor by inserting the tabs and pushing up

into position. Make sure the wires are not pinched

between the motor and the housing.

B25

Turn on the power source.

ON

OFF

B26

Test the motor. If the motor does not run,

check the plug connection.

B24

J

Secure the motor by tightening the 2 screws.

42929-01 10/26/2010

EXISTING FAN

C11

C12

E

F

Existing Construction – accessible from above

11

NO EXISTING FAN

8”

8 1/2”

OR

Remove an existing fan and check to make sure the

opening is large enough to accommodate the new

motor housing (8”x 8 1/2”).

Cut out an opening for the housing.

Use the motor housing as a template to mark position.

Slide the mounting rails into brackets.

Position the correct depth mark at the bottom edge of the

joist based on the thickness of your sheetrock.

5/8

1/2

5/8

1/2

C13

C14

Mark position of screws by using holes as a template.

42929-01 10/26/2010

C17

C18

C19

C20

12

C15 C16

Drill a hole in the center of each outline. Insert screws, leaving space between the screw head

and the joist. Screws are not provided.

Attach the rails onto the screws. Tighten screws.

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may

need to be purchased.

Route wires through the strain relief.

42929-01 10/26/2010

C21

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

C22

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

13

Tighten the strain relief screws.

Connect wires as shown.

C24

I

H

G

C23

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under the

wiring cover plate.

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

42929-01 10/26/2010

C25

I

C26

J

C27

ON

OFF

C28

14

Secure the motor by tightening the 2 screws.

Turn on the power source.

Reinstall the motor by inserting the tabs and pushing up

into position. Make sure the wires are not pinched

between the motor and the housing.

Test the motor. If the motor does not run,

check the plug connection.

C29

E1

Go to step

on page 17

to attach grille.

42929-01 10/26/2010

EXISTING FAN

D11

F

D12

15

Existing Construction – accessible only from below

D13

2

1

D14

Route wires through strain relief.

Remove an existing fan and check to make sure the open-

ing is large enough to accommodate the new motor hous-

ing (8”x 8 1/2”).

Move the housing into position above the ceiling

Attach existing ducting to duct connector. Tape joints.

If ducting does not fit securely,

an adapter may need to be purchased.

F

D15

Install the housing flush with the sheetrock and secure by

tightening the pre-loaded screws into the joist.

42929-01 10/26/2010

16

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

D16

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

I

D18

I

D19

D20

J

Connect wires as shown.

Reinstall the motor by inserting the tabs and pushing up

into position. Make sure the wires are not pinched between

the motor and the housing.

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

Secure the motor by tightening the 2 screws.

G

D17

H

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under

the wiring cover plate.

42929-01 10/26/2010

17

ON

OFF

D22

D23

E1

Go to step

on page 17

to attach grille.

D21

Test the motor. If the motor does not run, check the plug

connection.

Turn on the power source.

Attaching the Grille

Remove the thumbscrews. Connect wiring harness. DO NOT ALLOW THE FIXTURE TO

HANG FROM THE WIRING HARNESS.

N

F

E1

M

E2

42929-01 10/26/2010

18

Install bulbs (not included).

E8

Attach thumbscrews.

WARNING: To reduce the risk of electrical shock,

all 4 thumbscrews MUST be properly installed.

N

E7

Align posts A, B, C and D (stamped into motor hous-

ing) with posts A, B, C and D (stamped into light

fixture). Slide light fixture over posts.

M

E6

42929-01 10/26/2010

M

E5

K

M

E4

M

E3

Remove the strain relief bracket screw. Position the strain relief bracket under the

motor as shown.

Insert the strain relief bracket’s dog-leg tab so that

it hooks over the lip of the motor. Reinstall the

strain relief bracket screw.

Align glass dome and push up.

19

E10

P

Screw finial into position.

E9

O

42929-01 10/26/2010

Complete.

20

42929-01 10/26/2010

Trouble Shooting

Problem: Fan does not come on.

Solution:

• Harbor Breeze Fan Bath Ventilators are extremely quiet. To conrm that the fan is running, place your hand

near the vents to feel the air movement.

• Turn power on, replace fuse, or reset breaker.

• Check all plug connections to be sure they are secure.

• Check the wiring to make sure it matches the wiring diagram.

Problem: Light does not come on.

Solution:

• Replace the light bulb with a new bulb.

• Turn power on, replace fuse, or reset breaker.

• Check all plug connections to be sure they are secure.

• Check the wiring to make sure it matches the wiring diagram.

Problem: Fan is noisy.

Solution:

• Check and tighten all fasteners.

• Check the glass to make sure it is secure.

• Check the apper to make sure it moves freely.

If you need parts or service assistance, please call 888-830-1326 or visit us at our web site at http://www.

hunterfan.com.

La page charge ...

Hunter Fan 82022 Le manuel du propriétaire

Hunter Fan 82022 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents