Moog Videolarm ACH13HB8NE Installation And Operation Instructions Manual

Marque: Moog Videolarm

Modèle: ACH13HB8NE

Catégorie: Jouets

Taper: Installation And Operation Instructions Manual

Ce manuel convient également à

ACH13HB8N

www.moogvideolarm.com

A C H 1 3 H B 8 N

Aluminum Outdoor Environmental Camera Housings

Installation and Operation Instructions for the following models:

ACH13HB8N Outdoor environmental housing for PoE plug enabled IP xed cameras,

wall/pole mount, dynamic (intelligent) power allocation heater/blower

system, 30W midspan (100-240Vac input 50/60Hz)

ACH13HB8NE Outdoor environmental housing for PoE plug enabled IP xed cameras,

wall/pole mount, dynamic (intelligent) power allocation heater/blower

system

Before attempting to connect or operate this product, please read these instructions completely.

81-IN5455

06-26-2012

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. This installation should be made by a qualied service person and should conform

to all local codes.

b. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including ampliers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specied by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the integrity

of the installation is intact. Failure to comply with the foregoing could result in the unit separating

from the support structure and falling, with resultant damages or injury to anyone or anything struck

by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make future

shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us at

the following number:

The lightning ash with an arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of non-insulated

“dangerous voltage” within the product’s

enclosure that may be of sufcient magnitude

to constitute a risk to persons.

Este símbolo se piensa para alertar al usuario a la presencia

del “voltaje peligroso no-aisIado” dentro del recinto de los

productos que puede ser un riesgo de choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la presence

“de la tension dangereuse” non-isolée dans la clôture de

produits qui peut être un risque de choc électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença “di

tensão perigosa non-isolada” dentro do cerco dos produtos

que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla presenza

“di tensione pericolosa” non-isolata all’interno della

recinzione dei prodotti che può essere un rischio di scossa

elettrica

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones importantes

en la literatura que acompaña la aplicación.

Ce symbole de point d’exclamation est prévu pour alerter

l’utilisateur à la presence des instructions importantes dans

la littérature accompagnant l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der Literatur

alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido alertar o

usuário à presença de instruções importantes na literatura

que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti nella

letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800 - 554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING

TO QUALIFIED SERVICE PERSONNEL.

Limited Warranty for Moog Videolarm Products

Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:

PRODUCT CATEGORY PARTS \ LABOR

All Enclosures and Electronics* Five (5) Years

Poles/PolEvators™/CamEvator Three (3) Years

Warrior Series™/Q-View™/IR Illuminators Five (5) Years

SView Series™ Five (5) Years **6 months if used in auto scan/tour operation

Controllers Five (5) Years

Power Supplies Five (5) Years

EcoKit Three (3) Years

Accessory Brackets Five (5) Years

Liberty Dome Three (3) Years

*DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™ Three (3) Years **6 months if used in auto scan/tour operation

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Moog Videolarm

Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with

a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support

Team at 800.554.1124, extension 101. Moog Videolarm will return the repaired Product freight prepaid to Purchaser. Moog Videolarm is not obligated to

provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or

parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions.

TERMS AND CONDITIONS

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an

explanation of the claim shall be given promptly by Purchaser to Moog Videolarm. All claims for warranty service must be made within the warranty period.

If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of

investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period

of the entire Product. The speci c warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that

part or the remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any

Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the

warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes,

earthquakes), modi cation, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance

procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the

Product. Furthermore, Moog Videolarm shall have no liability where a schedule is speci ed for regular replacement or maintenance or cleaning of certain parts

(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-quali ed personnel; operation of the Product outside of the

published environmental and electrical parameters, or if such Product’s original identi cation (trademark, serial number) markings have been defaced, altered,

or removed. Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not

been sold by Moog Videolarm to the Purchaser. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS”

(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. Any

cost associated with removal of defective product and installation of replacement product is not included in this warranty.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR

ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL

CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT

THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS

PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF Moog Videolarm, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND

WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL

PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER

FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,

REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

ACH13HB8N

Input Power: 100 to 240VAC

Power: .8A

Frequency: 50 to 60 HZ

Output

Camera: POE (55VDC)

Heater: 55VDC (max. 20W)

Energía de entrada: 100 a 240VAC:

Energía: .8A

Frecuencia: 50 a 60 hertzios

Salida:

Cámara: POE (55VDC)

Calentador: 55VDC (máximo 20W)

Puissance d'entrée : 100 à 240VAC

Puissance: .8A

Fréquence: 50 à 60 hertz

Rendement

Appareil-photo : POE (55VDC)

Réchauffeur : 55VDC (maximum 20W)

Zugeführte Energie: 100 zu 240VAC

Energie: .8A

Frequenz: 50 bis 60 Hz

Ausgang

Kamera: POE (55VDC)

Heizung: 55VDC (Maximum 20W)

Poder de entrada: 100 a 240VAC

Poder: .8A

Freqüência: 50 a 60 hertz

Saída

Câmera: Ponto de entrada (55VDC)

Calefator: 55VDC (máximo 20W)

Alimentazione in ingresso di entrata: 100 a 240VAC

Potere: .8A

Frequenza: 50 - 60 hertz

Uscita

Macchina fotografica: POE (55VDC)

Riscaldatore: 55VDC (massimo 20W)

Français

Deutsch

Italiano

Portuguese

Español

English

Electrical Specifications

Midspan

Unpacking the Product

ACH13HB8N

* ACH13HB8N model only

Attach the bracket to the wall and secure

appropriately.

• Una el soporte a la pared y asegúrelo

apropiadamente.

• Attachez la parenthèse au mur et la fixez

convenablement.

• Bringen Sie den Haltewinkel zur Wand an und

sichern Sie passend.

• Una o suporte à parede e fixe-o

apropriadamente.

• Fissi la staffa alla parete e fissi giustamente.

Connect housing to wall bracket.

• Conecte la cubierta con el soporte de pared.

• Reliez le logement à la parenthèse de mur.

• Schließen Sie Gehäuse an Wandhaltewinkel an .

• Conecte a carcaça ao suporte de parede.

• Colleghi l'alloggiamento al supporto a mensola

1 2

Install the (2) cable strain relief plugs on the bottom

of the housing and tighten with the locknuts.

• Instale (2) los enchufes del retenedor de cable del cable en el

fondo de la cubierta y apriete con las tuercas de fijación.

• Installez (2) les prises de passe-fils de câble sur le fond du logement

et serrez avec les contre-écrous.

• Bringen Sie die (2) Kabelgummidurchführungsringstecker auf

die Unterseite des Gehäuses an und ziehen Sie mit den

Kontermuttern fest.

• Instale (2) os plugues do protetor da fiação do cabo no fundo da

carcaça e aperte-os com as contraporcas.

• Installi (2) le spine di gommino di protezione del cavo sulla

parte inferiore dell'alloggiamento e stringa con i contro

dadi.

Remove the (2) screws on top of the

housing and lift it open.

• Quite (2) los tornillos encima de la cubierta y levántelos

abiertos.

• Enlevez (2) les vis sur le logement et soulevez-les ouvertes.

• Entfernen Sie die (2) Schrauben auf das Gehäuse und heben

Sie sie geöffnet an.

• Remova (2) os parafusos no alto da carcaça e levante-os

abertos.

• Rimuova (2) le viti in cima all'alloggiamento ed alzile aperte.

Cable to camera (B), Network / Power (A). Unit is ready to power up.

• Cablegrafíe a la cámara (b), red hacia / fuera (a). La unidad está lista para accionar para arriba.

•

Câblez à l'appareil-photo (b), le réseau / dehors (a). L'unité est prête à mettre sous tension.

•

Kabeln Sie zu Kamera (b), Netz / heraus (a). Maßeinheit ist bereit, oben anzutreiben.

•

Cabografe à câmera (b), rede / para fora (a). A unidade está pronta para pôr acima.

•

Cavo alla macchina fotografica (B), rete / fuori (A). L'unità è pronta ad alimentare in su.

Power Reset

Network / Power

Network to Camera

LEDs

Plug in RJ45 input and output cables.

• Enchufe los cables de entrada RJ45 y de la salida.

• Branchez les câbles de l'entrée RJ45 et du rendement.

• Schließen Sie Kabel des Einganges RJ45 und des Ausganges an.

• Obstrua dentro cabos da entrada RJ45 e da saída.

• Inserisca i cavi dell'input RJ45 e dell'uscita

Place camera on sled and align mounting holes on

each. Adjust camera parallel to sled and tighten the

bolt on the bottom.

• Coloque la cámara fotográfica en el trineo y alinee los agujeros de

montaje en cada uno. Ajuste la cámara fotográfica paralela al trineo y

apriete el perno en el fondo.

• Placez l'appareil-photo sur le traîneau et alignez les trous de support sur

chacun. Ajustez l'appareil-photo parallèle au traîneau et serrez le

boulon sur le fond.

• Setzen Sie Kamera auf Schlitten und richten Sie Entlüftungslöcher auf

jedem aus. Justieren Sie die Kamera, die zum Schlitten parallel ist und

ziehen Sie den Schraubbolzen auf der Unterseite fest.

• Coloque a câmera no trenó e alinhe furos de montagem em cada um.

Ajuste a câmera paralela ao trenó e aperte o parafuso no fundo.

• Disponga la macchina fotografica sulla slitta ed allinei i fori di montag-

gio su ciascuno. Registri la macchina fotografica parallela alla slitta e

stringa il bullone sulla parte inferiore.

Sled

Screw

Camera Sled

Press the Calibration button for one second. Both the Test and Heat LED will turn ON. Once the unit has been

successfully calibrated, the Test and Heat LED will turn OFF. Once this is complete the Heat LED will turn ON only

if the heater is ON.

• Pulse el botón de calibración durante un segundo. Tanto la prueba y el calor se encenderá. Una vez que la unidad ha sido calibrado correctamente, la

prueba y el calor del LED se apagará. Una vez que se trata de completar el calor se encenderá sólo si el calentador está encendido.

• Appuyez sur le bouton d'étalonnage pour une seconde. Tant le test et la chaleur LED s'allume. Une fois l'appareil a été étalonné avec succès, le test et la

chaleur LED s'éteindra. Une fois cette opération terminée, la chaleur LED s'allume que si le chauffage est allumé.

• Drücken Sie die Taste Kalibrierung für eine Sekunde. Sowohl der Test-und Wärme-LED leuchtet auf. Sobald das Gerät erfolgreich kalibriert wurde, wird die

Test-und Wärme-LED auszuschalten. Sobald dies abgeschlossen ist die Wärme-LED leuchtet auf, wenn die Heizung an ist.

• Pressione o botão de calibração para um segundo. Tanto o teste como calor LED acenderá. Uma vez que o aparelho foi calibrado com sucesso, o teste

e calor LED apaga-se. Uma vez que este é completar o calor LED acenderá se o aquecedor está ligado.

• Premere il pulsante di calibrazione per un secondo. Sia il test e di calore LED si accende. Una volta che l'unità è stata correttamente calibrata, il collaudo

e calore LED si spegne. Una volta che questo è completare il calore LED si accende solo se il riscaldatore è ON.

Button

HEAT

TEST

• The heater and blower will not start for 60 seconds after power is applied to the product.

• Wait for the camera to completely boot up before pressing the calibration button. This will allow for the most accurate calibration.

• El calentador y el ventilador no se iniciará durante 60 segundos después de la energía se aplica al producto.

• Espere a que la cámara para arrancar completamente antes de pulsar el botón de calibración. Esto permitirá la calibración más precisa.

• Le chauffage et de ventilation ne démarre pas pendant 60 secondes après mise sous tension est appliquée au produit.

• Attendez que l'appareil photo à démarrer complètement avant appuyant sur le bouton d'étalonnage. Cela permettra pour le calibrage le

plus précis.

• Die Heizung und das Gebläse wird nicht für 60 Sekunden nach dem Einschalten starten, um das Produkt angewendet wird.

• Warten Sie, bis sich die Kamera komplett hochfahren, bevor Sie die Kalibrierung Taste. Dies wird für die genaue Kalibrierung ermöglichen.

• Aquecedor e soprador A não será iniciado durante 60 segundos após a energia é aplicada ao produto.

• Aguarde até que a câmera completamente arrancar antes de premir o botão de calibração. Isto irá permitir a calibração mais precisas.

• Il riscaldamento e soffiante non inizierà per 60 secondi dopo l'alimentazione è applicata al prodotto.

• Attendere che la macchina fotografica per avviare completamente a prima di premere il pulsante di calibrazione. Questo permetterà la

taratura più accurata.

WARNING!

Adjust the focus and focal length until the

desired field of view and focus is obtained.

• Ajuste el foco y la longitud focal hasta que el campo visual

deseado y el foco se obtiene.

• Ajustez le foyer et la longueur focale jusqu'à ce que le champ

visuel désiré et le foyer soit obtenu.

• Justieren Sie den Fokus und die fokale Länge, bis gewünscht

von der Ansicht auffangen und Fokus erhalten wird.

• Ajuste o foco e o comprimento focal até que o campo de

vista desejado e de foco esteja obtido.

• Registri il fuoco e la lunghezza focale fino ad ottenere il

campo voluto di visibilità ed il fuoco.

Adjust

Lens

Here

If mounting to pole, attach assembly using 3/4” mount-

ing straps (not provided).

• Si monta al poste, una a asamblea usando las correas que montan del

3/4"(no proporcionadas).

• Si montant au poteau, attachez l'assemblée en utilisant les courroies de

montage de 3/4"(non fournies).

• Bei der Befestigung zum Pfosten, bringen Sie Versammlung mit 3/4"den

Befestigungsbügeln an (nicht bereitgestellt).

• Se montando ao pólo, una o conjunto usando as cintas de montagem

de 3/4"(não fornecidas).

• Se montando al palo, fissi il complessivo usando le cinghie di montag-

gio di 3/4"(non fornite).

Close the top cover and tighten to the base with the

hex screws.

• Cierre la cubierta superior y apriete a la base con los tornillos

de la tuerca hexagonal.

• Fermez la couverture supérieure et serrez à la base avec les

vis de sortilège.

• Schließen Sie die obere Abdeckung und ziehen Sie zur

Unterseite mit den Hexagonschrauben fest.

• Feche a tampa superior e aperte-a à base com os parafusos

do hex.

• Chiuda la copertura superiore e stringa alla base con le viti

del hex.

If desired, use security screws in place of hex screws.

• Si está deseado, utilice los tornillos de la seguridad en

lugar de los tornillos de la tuerca hexagonal.

• Si désiré, utilisez les vis de sécurité au lieu des vis de sortilège.

• Wenn Sie gewünscht werden, benutzen Sie die Sicherheit

Schrauben anstatt der Hexagonschrauben.

• Se desejado, use os parafusos da segurança no lugar

dos parafusos do hex.

• Se voluto, utilizzi le viti di sicurezza al posto delle viti del hex.

Replacement Parts List

Part Number Description

1 RPACH010 ACH13 Front Endcap Assembly

2 RPACH020 ACH13 Lid Screws

3 RPHACH8N Heater for POE housing

RPACH050 12V Heater & Thermostat Kit For ACH13

RPACH060 ACH13 Top Extrusion

RPACH070 ACH13 Bottom Extrusion

8 RPPCBPOE PC board for POE housing

9 RPACH110

RPACHPK Packet Assembly

ACH13 Rear Endcap Assembly

11 WM800 Medium Duty W all Mount Bracket For ACH13

12 ACH130 ACH13 Vent Hole Plugs

RPBACH8N Blower for POE housing

ACH13HB8N

Product Registration/Warranty

Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest

quality products available and superior customer service.

Should a problem arise, rest assured that Moog Videolarm stands behind its products by offering impressive 3 Year and 5 Year warranties, depending on the product

purchased. See full warranty details at www.moogvideolarm.com/technical-support/warranty-plan/

Please take a few moments to register your purchase via the Online Product Registration Form at:

www.moogvideolarm.com/technical-support/product-registration

• Simple and Trouble-Free RMA process

• Receive product updates, and special promotion

• Eliminate the need to archive original purchase documents:

Receipts, Purchase Orders, etc…