Moog Videolarm PFH10C8WY Installation And Operation Instructions Manual

Marque: Moog Videolarm

Modèle: PFH10C8WY

Catégorie: Boîtiers de caméra

Taper: Installation And Operation Instructions Manual

Ce manuel convient également à

www.moogvideolarm.com

P F H 1 0

Outdoor Tubular Dust-Proof and Pressurized Environmental Housings

Installation and Operation Instructions for the following models:

PFH10C2W An Pressurized tubular housing, 24Vac or 12Vdc input, heater & blower with

feed-thru wall / pole mount

PFH10C2WY Pressurized tubular housing, 24Vac or 12Vdc input, heater & blower with

feed-thru wall / pole mount, adjustable sunshield

PFH10C8WY Pressurized tubular housing, PoE input with Dynamic Power Allocation, 30 watt

midspan included, heater & blower with feed-thru wall / pole mount, supports

.af PoE cameras, adjustable sunshield

DFH10C2W Dust-Proof tubular housing, 24Vac or 12Vdc input, heater & blower with

feed-thru wall / pole mount

DFH10C2WY Dust-Proof tubular housing, 24Vac or 12Vdc input, heater & blower with

feed-thru wall / pole mount, adjustable sunshield

DFH10C8WY Dust-Proof tubular housing, PoE input with Dynamic Power Allocation, 30

watt midspan included, heater & blower with feed-thru wall / pole mount,

supports .af PoE cameras, adjustable sunshield

Before attempting to connect or operate this product, please read these instructions completely.

81-IN5480

06-18-2012

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. The installation should be made by a qualied installer.

b. The installation should be in compliance with local codes.

c. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including ampliers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specied by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the integrity

of the installation is intact. Failure to comply with the foregoing could result in the unit separating

from the support structure and falling, with resultant damages or injury to anyone or anything struck

by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make future

shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us at

the following number:

The lightning ash with an arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of non-insulated

“dangerous voltage” within the product’s

enclosure that may be of sufcient magnitude

to constitute a risk to persons.

Este símbolo se piensa para alertar al usuario a la presencia

del “voltaje peligroso no-aisIado” dentro del recinto de los

productos que puede ser un riesgo de choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la presence

“de la tension dangereuse” non-isolée dans la clôture de

produits qui peut être un risque de choc électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença “di

tensão perigosa non-isolada” dentro do cerco dos produtos

que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla presenza

“di tensione pericolosa” non-isolata all’interno della

recinzione dei prodotti che può essere un rischio di scossa

elettrica

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones importantes

en la literatura que acompaña la aplicación.

Ce symbole de point d’exclamation est prévu pour alerter

l’utilisateur à la presence des instructions importantes dans

la littérature accompagnant l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der Literatur

alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido alertar o

usuário à presença de instruções importantes na literatura

que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti nella

letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800 - 554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING

TO QUALIFIED SERVICE PERSONNEL.

Limited Warranty for Moog Videolarm Products

Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:

PRODUCT CATEGORY PARTS \ LABOR

All Enclosures and Electronics* Five (5) Years

Poles/PolEvators™/CamEvator Three (3) Years

Warrior Series™/Q-View™/IR Illuminators Five (5) Years

SView Series™ Five (5) Years **6 months if used in auto scan/tour operation

Controllers Five (5) Years

Power Supplies Five (5) Years

EcoKit Three (3) Years

Accessory Brackets Five (5) Years

Liberty Dome Three (3) Years

*DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™ Three (3) Years **6 months if used in auto scan/tour operation

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Moog Videolarm

Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with

a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support

Team at 800.554.1124, extension 101. Moog Videolarm will return the repaired Product freight prepaid to Purchaser. Moog Videolarm is not obligated to

provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or

parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions.

TERMS AND CONDITIONS

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an

explanation of the claim shall be given promptly by Purchaser to Moog Videolarm. All claims for warranty service must be made within the warranty period.

If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of

investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period

of the entire Product. The speci c warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that

part or the remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any

Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the

warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes,

earthquakes), modi cation, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance

procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the

Product. Furthermore, Moog Videolarm shall have no liability where a schedule is speci ed for regular replacement or maintenance or cleaning of certain parts

(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-quali ed personnel; operation of the Product outside of the

published environmental and electrical parameters, or if such Product’s original identi cation (trademark, serial number) markings have been defaced, altered,

or removed. Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not

been sold by Moog Videolarm to the Purchaser. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS”

(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. Any

cost associated with removal of defective product and installation of replacement product is not included in this warranty.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR

ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL

CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT

THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS

PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF Moog Videolarm, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND

WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL

PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER

FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,

REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

P F H 1 0

Value Features

Hand Hold

underlaid grip point

Multi-Plane

Adjustable SunShield

position to protect

against glare on lens

Cable Feed Through

hides and protects cables

Pop Out Tabs

allows for

pole mounting

Rear Access Panel

acts as internal J-Box

Installers Connection Board

allows for easy hook-ups

Lanyard Cable

safely retains housing

during installation

Durable and Attractive

“grite” color powder coated

nish. (increased corrosion

protection nish available)

Optional Accessory

Contents of Box

Midspan

for

Some Models

PFH10

24Vac 29W (No camera)

12Vdc 11W (No camera)

24Vac 29W (Ninguna cámara)

12Vdc 11W (Ninguna cámara)

24Vac 29W (Aucun appareil-photo)

12Vdc 11W (Aucun appareil-photo)

24Vac 29W (Keine Kamera)

12Vdc 11W (Keine Kamera)

24Vac 29W (Nenhuma câmera)

12Vdc 11W (Nenhuma câmera)

24Vac 29W (Nessuna macchina fotografica)

12Vdc 11W (Nessuna macchina fotografica)

Electrical Specifications

Power 12VDC

Class 2 Only

Français

Deutsch

Italiano

Portuguese

Español

English

ADDITIONAL DETAIL TO BE UPDATED IN FUTURE REVISIONS

CAUTION: When assembling the mounting bracket, make sure

all the wiring access holes are facing towards the rear of the

base mounts access portal.

• PRECAUCIÓN: Al montar la consola de montaje, cerciórese de que todos los agujeros

de acceso del cableado son revestimiento hacia la parte posterior del portal bajo del

acceso de los montajes.

• ATTENTION : En assemblant le support, assurez-vous que toutes les ouvertures

d'accès de câblage sont revêtement vers l'arrière du portail bas d'accès de bâtis.

• VORSICHT: Wenn Sie die Schienenplatte zusammenbauen, stellen Sie sicher, dass alle

VerdrahtungsZugangslöcher Einfassung in Richtung zur Rückseite des niedrigen

Einfassungszugangsportals sind.

• CUIDADO: Ao montar o suporte, certique-se que todos os furos de acesso da ação

são revestimento para a parte traseira do portal baixo do acesso das montagens.

• ATTENZIONE: Nel montare il montaggio - la staffa, si assicura che tutti i fori di

accesso dei collegamenti siano rivestimento verso la parte posteriore del portale

basso di accesso dei supporti.

Proper Assembly of Mounting Bracket

Wiring Access Holes:

Must be rear facing

Recommended Hardware for the Mounting Holes:

• 5/16” - 18 (or M8 for metric) x minimum 1 ¼” Hex Head Bolt

• 5/16” Flat Washer

• 5/16” Lock Washer

Mounting Straps Sold Separately

If you are running a conduit to the housing instead of through

mount wiring, rst install the appropriate tting to the wall mount.

• Si usted está funcionando con un conducto a la cubierta en vez del cableado directo

del montaje, primero instale la guarnición apropiada al montaje de la pared.

• Si vous courez un conduit au logement au lieu du câblage traversant de bâti, installez

d'abord l'ajustage de précision approprié sur le bâti de mur.

• Wenn Sie ein Rohr zum Gehäuse anstelle von der durchgehenden Einfassungsverdrahtung

laufen lassen, bringen Sie zuerst die passende Befestigung zur Wandeinfassung an.

• Se você está funcionando uma canalização à carcaça em vez da ação direta da montagem,

instale primeiramente o encaixe apropriado à montagem da parede.

• Se stiate facendo funzionare un condotto all'alloggiamento anziché i collegamenti diretti del

supporto, in primo luogo installi il montaggio adatto al supporto della parete.

Attach mount to wall with suitable hardware (not provided).

• Ate el montaje a la pared con el hardware conveniente (no proporcionado).

• Attachez le bâti au mur avec le matériel approprié (non fourni).

• Bringen Sie Einfassung zur Wand mit der verwendbaren Hardware an (nicht bereitgestellt).

• Una a montagem à parede com a ferragem apropriada (não fornecida).

• Attacchi il supporto alla parete con ssaggi adatti (non forniti).

WALL MOUNTING

If attaching to pole, rst break away tabs with pliers and remove

(4) strap plugs.

• Si atan al poste, el primeros rompen lejos lengüetas con los alicates y quitan (4) los enchufes

de la correa.

• Si attachant au poteau, les premiers cassent loin des étiquettes avec des pinces et enlèvent

(4) des prises de courroie.

• Bei der Befestigung zum Pfosten, brechen erste weg Vorsprünge mit Zangen und entfernen

(4) Bügelstecker.

• Se unindo ao pólo, o primeiros quebram afastado abas com alicates e removem (4) plugues

da cinta.

• Se attaccando al palo, i primi rompono via le linguette con le pinze e rimuovono (4) la cinghia

tappa.

TAB

POLE MOUNTING

Reference view of mount after removing the tabs and adding

the wall mount straps.

• Reérase a la vista del montaje después de quitar las lengüetas y de agregar las correas

del montaje de la pared .

• Mettez en référence la vue du bâti après avoir enlevé les étiquettes et avoir ajouté les

courroies de bâti de mur.

• Beziehen Sie Ansicht der Einfassung, nachdem Sie die Vorsprünge entfernt haben und

die Wandeinfassungsbügel addiert haben.

• Proveja a vista da montagem após ter removido as abas e ter adicionado as cintas da

montagem da parede.

• Riferisca la vista del supporto dopo l'eliminazione delle linguette e l'aggiunta delle cinghie

del supporto della parete .

Crimp the connectors as needed. Then use cable ties

on the nipples to secure device, leave extra cable.

• Prense los conectadores según lo necesitado. Entonces utilice las ataduras de cables en las

entrerroscas para asegurar el dispositivo, dejan el cable adicional.

• Sertissez par replis les connecteurs comme nécessaires. Utilisez alors les serres-câble sur les

mamelons pour xer le dispositif, laissent le câble supplémentaire.

• Quetschverbinden Sie die Verbindungsstücke, wie gebraucht. Benutzen Sie dann Kabelbinder

auf den Nippeln, um Vorrichtung zu sichern, lassen Extrakabel.

• Frise os conectores como necessários. Use então cintas plásticas nos bocais para xar o

dispositivo, deixam o cabo extra.

• Unisca i connettori come stati necessari. Allora utilizzi le fascette ferma-cavo sugli ugelli per

assicurare il dispositivo, lasciano il cavo supplementare.

Cable

Crimp

Cable Ties

Feed cable through bracket, pierce the gasket nipples

(as needed). Place the gasket as shown.

• Alimente el cable a través del soporte, perfore las entrerroscas de la junta (según lo necesitado).

Coloque la junta como se muestra.

• Alimentez le câble par la parenthèse, percez les mamelons de garniture (comme nécessaire).

Placez la garniture comme montrée.

• Ziehen Sie Kabel durch Haltewinkel ein, durchbohren Sie die Dichtungsnippel (wie gebraucht).

Setzen Sie die Dichtung wie gezeigt.

• Alimente o cabo através do suporte, perfure os bocais da gaxeta (como necessário). Coloc a

gaxeta como mostrada.

• Alimenti il cavo tramite la staffa, perfori gli ugelli della guarnizione (come stato necessario).

Disponga la guarnizione come indicata.

Cable

Gasket Nipples

Feed cable through back of bracket or bottom access point.

Then follow instructions from previous block.

• Alimente el cable a través detrás del soporte o del punto de acceso inferior. Entonces siga las

instrucciones del bloque anterior.

• Alimentez le câble à travers en arrière de la parenthèse ou du point d'accès inférieur. Suivez

alors les instructions du bloc précédent .

• Ziehen Sie Kabel durch zurück des Haltewinkels oder des unteren Zugangspunktes ein.

Befolgen Sie dann Anweisungen vom vorhergehenden Block .

• Seja o cabo completamente do suporte ou do ponto de acesso inferior. Siga então instruções

do bloco precedente.

• Alimenti il cavo attraverso indietro della staffa o del punto di accesso inferiore. Allora segua le

istruzioni dal blocco precedente .

Cable

Entry

Crimp

Cable

Entry

Place the housing on the bracket, use the provided captive

screws and the key to mount.

• Coloque la cubierta en el soporte, utilice los tornillos prisioneros proporcionados y la llave

al montaje.

• Placez le logement sur la parenthèse, employez les vis captives fournies et la clef au bâti.

• Setzen Sie das Gehäuse am Haltewinkel, verwenden Sie die zur Verfügung gestellten

Sicherheitsschrauben und den Schlüssel zur Einfassung.

• Coloc a carcaça no suporte, use os parafusos prisioneiros fornecidos e a chave à montagem.

• Disponga l'alloggiamento sulla staffa, usi le viti prigioniere fornite e la chiave al supporto.

(A-Tighten)

(B-Keep loose until step 6)

Pole Mount Option (Use Steel Straps to Mount)

Wall Mount Option

In order to rotate the rear cover, slightly loosen the screw marked (A) and completely loosen the screw marked (B). Then make all of the

nessecary wiring connections.

• Para girar la cubierta posterior, aoje levemente el (a) marcado tornillo y aoje totalmente el (b) marcado tornillo. Entonces haga todas las conexiones nessecary del cableado.

• An de tourner la couverture arrière, détachez légèrement le (a) marqué par vis et détachez complètement le (b) marqué par vis. Établissez alors tous les rapports nessecary de câblage.

• Um die hintere Abdeckung zu drehen, lösen Sie etwas das Schraube signikante (a) und lösen Sie vollständig das Schraube signikante (b). Stellen Sie dann alle nessecary Verdrahtungsbeziehungen her.

• A m girar a tampa traseira, afrouxe ligeiramente o (a) marcado parafuso e afrouxe completamente o (b) marcado parafuso. Faça então todas as conexões nessecary da ação.

• Per girare la copertura posteriore, allenti un po'la vite contrassegnata (A) e completamente allenti la vite contrassegnata (B). Allora faccia tutti collegamenti nessecary dei collegamenti.

(A- Slightly loosen)

(B- Completely loosen)

RJ45 (568B)

Power

BNC

Communication

Use provided Key to remove the front part of the housing.

• El uso proporcionó llave para quitar la parte delantera de la cubierta.

• L'utilisation a fourni la clef pour enlever la partie avant du logement.

• Gebrauch lieferte Schlüssel, um das Vorderteil des Gehäuses zu entfernen.

• O uso forneceu a chave para remover a parte dianteira da carcaça.

• L'uso ha fornito la chiave per rimuovere la parte anteriore dell'alloggiamento.

Lanyard Cable

Key (B) 1 lower screw

(A)

(A) 2 long screws

Reference inside view for showing board, ying cables and

attached connectors.

• Reérase dentro de la visión para demostrar el tablero, los cables que vuelan y los

conectadores atados.

• Mettez en référence à l'intérieur de la vue pour montrer le conseil, les câbles volants et

les connecteurs attachés.

• Beziehen Sie innerhalb der Ansicht für das Zeigen des Brettes, der iegenden Kabel und

der angebrachten Verbindungsstücke.

• Proveja dentro da vista para mostrar a placa, cabos de voo e conectores unidos.

• Riferimento all'interno della vista per la mostra bordo, i cavi volanti e dei connettori allegati.

Cable

Connectors

NOTE:

The power distribution board is designed with a 24Vac / 12Vdc

selector switch. If the Switch is set at 24Vac, then voltage input

should be 24Vac. 24Vac will then be output to the camera. If the

Switch is set at 12Vdc, then voltage input should be 12Vdc, 12Vdc

will then be output to the camera. The selector switch is to allow

the housing to operate at either voltage.

• El tablero de distribución de energía está diseñado con un selector de 24 Vac / 12 Vdc. Si el

interruptor se ha jado en 24 Vac,entonces la tensión de entrada debe ser 24 Vac. 24 Vac será

entonces la salida de la cámara. Si el interruptor se ha jado en 12 Vcc, entonces la tensión de

entrada debe ser de 12 Vdc, 12 Vdc a continuación será la salida a la camera. Selector es

permitir a la vivienda para operar a cualquier voltaje.

• Le tableau de distribution électrique est conçu avec un interrupteur 24Vac / 12Vdc sélecteur.

Si le commutateur est xé à 24Vac, puis la tension d'entrée doit être 24Vac. 24Vac sera alors

sortie de la caméra. Si le commutateur est xé à 12 Vdc, puis la tension d'entrée doit être

12Vdc, 12Vdc sera alors la sortie de l'interrupteur de sélection camera. Est de permettre

le logement de fonctionner à la tension soit.

• Die Stromverteilungsplatine wird mit einer 24 Vac / 12Vdc Wahlschalter konzipiert. Wenn

der Schalter auf 24Vac gesetzt ist, dann sollte Spannungseingang 24Vac. Wird 24Vac dann

an der Kamera sein. Wenn der Schalter auf 12Vdc eingestellt ist, dann sollte Spannungseingang

12Vdc, 12Vdc wird dann an den camera. Wahlschalter ist es, dass das Gehäuse entweder

an Spannung zu betreiben sein.

• O quadro de distribuição de energia é projetado com um interruptor 24Vac / 12 Vdc selector.

Se o interruptor está xado em 24Vac, depois da tensão de entrada deve ser 24Vac. 24Vac,

então, ser a saída para a câmera. Se o interruptor estiver na 12Vdc, em seguida, entrada de

tensão deve ser 12Vdc, 12Vdc será então a saída para o comutador selector camera. é permitir

que o invólucro para operar em qualquer tensão.

• La scheda di distribuzione dell'alimentazione è progettato con una 24Vac / 12Vdc selettore. Se

l'interruttore viene ssato a 24 Vac, quindi tensione di ingresso deve essere 24Vac. 24Vac sarà

quindi uscita alla fotocamera. Se l'interruttore viene ssato a 12Vdc, quindi tensione di ingresso

deve essere 12Vdc, 12Vdc sarà poi uscita allo switch camera. Di selezione è quello di permettere

l'alloggiamento di funzionare sia a tensione.

WARNING!

Make sure that the Voltage Selector Switch is set for the

correct input and camera supply voltage before power is

supplied. Failure to do this may result in damage to the

housing and void all warranties.

• Asegúrese de que el selector de tensión está ajustado para la entrada correcta y tensión

de alimentación de la cámara antes de la alimentación se suministra. No hacer esto puede

resultar en daños a la vivienda y anulará todas las garantías.

• Assurez-vous que le sélecteur de tension est réglé pour l'entrée et la tension d'alimentation

appareil photo avant de l'alimentation est fournie. Le défaut de ce faire peut entraîner des

dommages au logement et annulera toutes les garanties.

• Stellen Sie sicher, dass der Spannungswahlschalter für die richtige Eingabe und Kamera

Versorgungsspannung eingestellt ist, bevor Strom versorgt wird. Wenn Sie dies nicht tun,

kann es zu Schäden am Gehäuse führen und erlischt jegliche Gewährleistung.

• Certique-se de que o seletor de tensão é denido para a entrada correta e tensão de

alimentação da câmera antes de alimentação é fornecida. Não fazer isso pode resultar

em danos à carcaça e anular todas as garantias.

• Assicurarsi che il selettore di tensione sia impostato per l'ingresso corretto e tensione di

alimentazione della fotocamera prima che l'alimentazione viene fornita. In caso contrario

si possono causare danni al corpo e invalidare tutte le garanzie.

The power distribution board is located inside the housing at

the rear.

• El cuadro de distribución de alimentación se encuentra dentro de la carcasa en la parte trasera.

• Le tableau de distribution électrique est situé à l'intérieur du boîtier à l'arrière.

• Die Stromverteilungsplatine innerhalb des Gehäuses auf der Rückseite.

• A placa de distribuição de energia está localizado no interior do invólucro na parte traseira.

• La scheda di distribuzione di potenza è situato all'interno dell'alloggiamento sul retro.

24Vac /12Vdc

selector switch

Selectable

24Vac or 12Vdc

Analog

Video

Network

Data

Alarm / analog

communication

power out

to camera

The power distribution board is designed with a 24Vac/12Vdc

selector switch. Select the desired input voltage. No other

customer input is needed for this board.

• El tablero de distribución de energía está diseñado con un interruptor selector de 24Vac/12Vdc.

Seleccione el voltaje de entrada deseada. No hay entrada de otro cliente que se necesita para

este foro.

• Le tableau de distribution de puissance est conçu avec un commutateur sélecteur de

24Vac/12Vdc. Sélectionnez la tension d'entrée souhaitée. Aucun autre client d'entrée est

nécessaire pour ce conseil.

• Die Stromverteilungsplatine ist mit einem Wahlschalter 24Vac/12Vdc- konzipiert. Wählen Sie die

gewünschte Eingangsspannung. Kein anderer Kunde Eingang ist für dieses Board benötigt.

• O quadro de distribuição de energia é projetado com um interruptor 24Vac/12Vdc selector.

Seleccionar a tensão de entrada desejado. Nenhuma entrada de outro cliente é necessário para

este fórum.

• La scheda di distribuzione di potenza è progettato con un interruttore 24Vac/12Vdc selettore.

Selezionare la tensione di ingresso desiderato. Nessun ingresso altro cliente è necessario per

questa scheda.

24Vac /12Vdc

selector switch

Heater (-) Input (+) (-) Output (+) (-) Fan (+) } Factory Wiring

24Vac

12Vdc

14 15

Reference Block [15] Reference Block [15]

When pressurizing unit be sure to set the gauge or regulator

slightly above the housing pressure target of 5-7psi (0.35-0.5bar).

• Al presurizar la unidad esté seguro de jar el calibrador o el regulador levemente

sobre la blanco de la presión de la cubierta de 5-7psi (0.35-0.5bar).

• En pressurisant l'unité soyez sûr de placer la mesure ou le régulateur légèrement

au-dessus de la cible de pression de logement de 5-7psi (0.35-0.5bar).

• Wenn Sie Maßeinheit unter Druck setzen, seien Sie sicher, die Lehre oder den

Regler über das Gehäusedruckziel von 5-7psi (0.35-0.5bar) etwas einzustellen.

• Ao pressurizar a unidade seja certo ajustar ligeiramente o calibre ou o regulador

acima do alvo da pressão da carcaça de 5-7psi (0.35-0.5bar).

• Nel pressurizzare l'unità sia sicuro regolare un po'il calibro o il regolatore sopra

l'obiettivo di pressione dell'alloggiamento di 5-7psi (0.35-0.5bar).

PSI

100

150

200

250

300

Nitrogen

Tank

Hose

Regulator

Air Chuck

580

Fitting

Install the camera using provided screws and rubber spacer, to

center lens (if needed).

• Instale la cámara usando los tornillos proporcionados y el espaciador de goma, a la lente de

centro (si es necesario).

• Installez l'appareil-photo utilisant les vis fournies et l'entretoise en caoutchouc, sur l'objectif

central (si nécessaire).

• Bringen Sie die Kamera unter Verwendung der zur Verfügung gestellten Schrauben und der

Gummidistanzscheibe, zum Mittelobjektiv an (wenn erforderlich).

• Instale a câmera usando os parafusos fornecidos e o espaçador de borracha, à lente center

(se necessário).

• Stalli la macchina fotograca usando le viti fornite ed il distanziatore di gomma, all'obiettivo

concentrare (se necessario).

Loosen the screws shown on the picture and turn the camera

sled ring to the desired angle and re-tighten.

• Aoje los tornillos demostrados en el cuadro y dé vuelta al anillo del trineo de la cámara

al ángulo deseado y vuélvalo a apretar.

• Desserrez les vis montrées sur l'image et tournez l'anneau de traîneau d'appareil-photo

à l'angle désiré et le resserrez.

• Lösen Sie die Schrauben, die auf der Abbildung gezeigt werden und drehen Sie den

Kameraschlittenring zum gewünschten Winkel und ziehen Sie wieder an.

• Afrouxe os parafusos mostrados no retrato e gire o anel do trenó da câmera para o ângulo

desejado e reaperte-o.

• Allenti le viti indicate sull'immagine e giri l'anello della slitta della macchina fotograca

nell'angolo voluto e riserri.

Screw

Camera Sled Ring

Camera Sled

The front window can be removed in case the lens

requires adjustment.

• La ventana delantera puede ser quitada en caso de que la lente requiera el ajuste.

• La fenêtre avant peut être enlevée au cas où l'objectif exigerait l'ajustement.

• Das vordere Fenster kann entfernt werden, falls das Objektiv Justage erfordert.

• A janela dianteira pode ser removida caso que a lente exige o ajuste.

• La nestra anteriore può essere rimossa nel caso l'obiettivo richieda la registrazione.

HAND HOLD

18 19

Future Maintenance Pressurize the Unit (NOT required for the Dust Tight Unit)

Depress the ll valve. Drain all air

from the housing and repeat 3 times

to remove all moisture.

• Presione la válvula del terraplén. Salga todo el aire

de la cubierta y de la repetición 3 veces de quitar

toda la humedad.

• Enfoncez la valve de sufsance. Évacuez tout l'air le

logement et la répétition 3 fois d'enlever toute

l'humidité.

• Drücken Sie das Fülleventil nieder. Lassen Sie alle

Luft aus dem Gehäuse und der Wiederholung 3mal,

alle Feuchtigkeit zu entfernen ab.

• Comprima a válvula da suciência. Saia todo o ar da

carcaça e da repetição 3 vezes remover toda a

umidade.

• Deprima la valvola del materiale di riempimento.

Tolga tutta l'aria dall'alloggiamento e dalla

ripetizione 3 volte rimuovere tutta l'umidità.

Depress to Purge

Pressure Fill Schraeder Valve

Air Chuck

Place the air chuck on the ll valve

and begin lling until pressure relief

valve opens.

• Coloque la tirada del aire en la válvula del tanque y

comience a llenar hasta que la válvula de descarga

de presión se abra.

• Placez le mandrin d'air sur la valve de réservoir et

commencez à remplir jusqu'à ce que la valve de

décompression s'ouvre.

• Setzen Sie die Luftklemme auf das Behälterventil

und fangen Sie an zu füllen, bis Druckablassventil

sich öffnet.

• Coloc o mandril do ar na válvula do tanque e

comece a encher-se até que a válvula de escape de

pressão abra.

• Disponga il mandrino dell'aria sulla valvola del carro

armato e cominci a riempire no a che la valvola

limitatrice della pressione non si apra.

Over Relief Valve

(5-7psi)

Pressurize the Unit Cont.

Replacement Parts List

PFH10

DESCRIPTION PART #

1 RPVL3857 BACK COVER

RPVL3863

BACK COVER GASKET

RPVALV12

TANK VALVE

4 RPCA3682 CONNECTION BOARD

5 RPPFHPCK HARDWARE PACKET

6 RPVALV08 PRESSURE RELIEF VALVE

7 RPVL2968 HOUSING BODY

8 RPGK3880 WALL MOUNT GASKET

9 RPVL3858 HOUSING BRACKET

10 RPFTM2425G WALL MOUNT BRACKET

11 RPRSORG24 HOUSING ORING

12 RPVL3860 HOUSING NUT

13 RP76VL2015 PC BOARD

14 RPVL2969 CAMERA SLED ASSEMBLY

15 RPVL2965 HOUSING ASSEMBLY

16 RPVL3888 LANYARD SLED

17 RPVL2972 FRONT WINDOW ASSEMBLY

PSI

Fill Valve

Over - Pressure Relief Valve

Connectors

Pressure Gauge

NOT INCLUDED

Air Chuck

After purging and relling, check

the housings pressure. It should be

around 5-7psi (0.35-0.5bar).

• Después de purgar y de rellenar, compruebe la

presión de las cubiertas. Debe estar alrededor de

5-7psi (0.35-0.5bar).

• Après la purge et le remplissage, vériez la pression

de logements. Elle devrait être autour de 5-7psi

(0.35-0.5bar).

• Nachdem Sie bereinigt haben und wieder gefüllt

haben überprüfen Sie den Gehäusedruck. Er sollte

um 5-7psi (0.35-0.5bar) sein.

• Após a remoção e o reenchimento, veric a pressão

das carcaças. Deve ser em torno de 5-7psi

(0.35-0.5bar).

• Dopo l'eliminazione dell'inceppo ed il riempimento,

controlli la pressione degli alloggiamenti. Dovrebbe

essere intorno a 5-7psi (0.35-0.5bar).

Product Registration/Warranty

Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest

quality products available and superior customer service.

Should a problem arise, rest assure that Moog Videolarm stands behind its products by offering impressive warranty plans: 3 Years on all Housings, Poles,

Power Supplies, and Accessories and 5 Years on camera systems (SView, QView, Warriors), and InfraRed Illuminators.

Take a few moments and validate your purchase via the Online Product Registration Form at

www.videolarm.com/productregistra tion.jsp

• Simple and Trouble-Free RMA process

• Added into customer database to receive product updates / news

• Eliminate the need to archive original purchase documents:

Receipts, Purchase Orders, etc…