CARLO GAVAZZI WM1596AV53XOSXKR Manuel utilisateur

WM15

Power analyser for three-phase systems

USER MANUAL

2 WM15 - User manual | CARLO GAVAZZI Controls SpAWM15 - User manual | CARLO GAVAZZI Controls SpA

Summary

WM15 5

Preliminary remarks 5

Description 5

Available versions 6

UCS (Universal Conguration Software) 7

Use of WM15 8

Preliminary remarks 8

SETTINGS menu display 8

INFO menu display 8

RESET menu display 9

Measurement page display 9

Information and warnings 9

Commissioning 10

Preliminary settings 10

MID SETTINGS menu 10

QUICK SETUP menu 11

WIRING CHECK menu 12

Performing operations in WM15 13

Performing operations in the measurement pages 13

Performing operations in the SETTINGS menu 13

Performing operations in the INFO menu 13

Performing operations in the RESET menu 13

Menu description 14

Measurement pages 14

SETTINGS menu 16

INFO menu 16

RESET menu 17

Things you should be aware of 18

Preliminary remarks 18

Variables 18

Alarm types 18

Average value calculation (dmd) 19

Integration interval 19

Home page 20

Backlight 20

Screensaver 20

Page lter 20

Restoring the settings using the RESET menu 20

Restoring the settings using the reset button 20

Preliminary remarks 21

Display check 21

Check from UCS software or UCS Mobile 21

Virtual correction from UCS software or UCS Mobile 21

3WM15 - User manual | CARLO GAVAZZI Controls SpAWM15 - User manual | CARLO GAVAZZI Controls SpA

Maintenance and disposal 22

Measuring problems 22

Alarms 22

Communication problems 22

Display problem 22

4 WM15 - User manual | CARLO GAVAZZI Controls SpAWM15 - User manual | CARLO GAVAZZI Controls SpA

Information property

CARLO GAVAZZI Controls SpA reserves the right to apply modifications or make improvements to the relative documentation without the

obligation of advance notice.

Safety messages

The following section describes the warnings related to user and device safety included in this document:

NOTICE: indicates obligations that if not observed may lead to damage to the device.

CAUTION! Indicates a risky situation which, if not avoided, may cause data loss.

IMPORTANT: provides essential information on completing the task that should not be neglected.

General warnings

This manual is an integral part of the product and accompanies it for its entire working life. It should be consulted for all situations

tied to configuration, use and maintenance. For this reason, it should always be accessible to operators.

NOTICE: no one is authorized to open the analyzer or remove the MABC module. This operation is reserved exclusively for CARLO

GAVAZZI technical service personnel.

Protection may be impaired if the instrument is used in a manner not specified by the manufacturer.

Service and warranty

In the event of malfunction, fault, requests for information or to purchase accessory modules, contact the CARLO GAVAZZI branch or

distributor in your country.

Installation and use of analyzers other than those indicated in the provided instructions and removal of the MABC module void the warranty.

Download

This manual www.productselection.net/MANUALS/UK/WM15_im_use.pdf

Installation instructions - WM15 www.productselection.net/MANUALS/UK/WM15_im_inst.pdf

UCS software www.productselection.net/Download/UK/ucs.zip

5WM15 - User manual | CARLO GAVAZZI Controls SpAWM15 - User manual | CARLO GAVAZZI Controls SpA

WM15

Introduction

WM15 is a power analyser for single-, two- and three-phase systems.

Depending on the model, WM15 is equipped with a static output (pulse or alarm) or with a static output and a Modbus RTU

static communication port.

The self-powered version can be installed on systems with voltage up to 415 V L-L, while the version with auxiliary power sup-

ply can be installed on systems with voltage up to 600 V L-L.

Description

Front

Part Description

A Optical port for easy programming and diagnostics through Optoprog

B Matrix LCD display

C Mechanical keys

D Grooves for side brackets

6 WM15 - User manual | CARLO GAVAZZI Controls SpAWM15 - User manual | CARLO GAVAZZI Controls SpA

WM15

Rear

Part Description

A Power supply (version with auxiliary supply)

B Three-phase voltage inputs

C RS485 + digital output

D Three-phase current inputs

Available versions

Code Description

WM1596AV53XOSX Self power supply, 415 V L-L. Digital output and RS485, not MID

WM1596AV53XOSPFB Self power supply, 415 V L-L. Digital output and RS485, MID

WM1596AV53XOXX Self power supply, 415 V L-L. Digital output, not MID

WM1596AV53XOXPFB Self power supply, 415 V L-L. Digital output, MID

WM1596AV53HOSX Auxiliary supply, 600 V L-L. Digital output and RS485, not MID

7WM15 - User manual | CARLO GAVAZZI Controls SpAWM15 - User manual | CARLO GAVAZZI Controls SpA

WM15

UCS (Universal Conguration Software)

UCS is available in desktop and mobile versions.

It may connect to WM15 via RS485 (RTU protocol, desktop version only) or through OptoProg (via Bluetooth).

UCS allows to:

• set up the WM15 unit (online or offline);

• display the system state for diagnostic and setup verification purposes

Overview of the UCS functions:

• Setting up the system with WM15 connected (online setup)

• Defining the setup with WM15 non connected, then applying it at a later time (offline setup)

• Displaying the main measurements

• Displaying the state of inputs and outputs

• Displaying the state of the alarms

• Recording the measurements of selected variables (UCS Desktop version only)

• Displaying the quick help on installing WM15 and connecting with OptoProg (UCS Mobile version only)

8 WM15 - User manual | CARLO GAVAZZI Controls SpAWM15 - User manual | CARLO GAVAZZI Controls SpA

Use of WM15

Interface

Introduction

WM15 is organised into two menus:

• Main menu, divided into three sub-menus:

» SETTINGS: pages allowing to set the parameters

» INFO: pages displaying general information and the set parameters

» RESET: pages allowing to reset the partial counters and the dmd calculation, or to restore the factory settings

• Measurement pages: pages allowing to display the meters and the other electrical variables

SETTINGS menu display

Part

Description

A

Menu title

B

Sub-menu title, see “SETTINGS menu” on page 16

C

Parameter

D

Current parameter information

INFO menu display

Part

Description

A

Menu title

B

Sub-menu title, see “INFO menu” on page 17

C

Parameter

D

Current parameter information

9WM15 - User manual | CARLO GAVAZZI Controls SpAWM15 - User manual | CARLO GAVAZZI Controls SpA

Measurement page display

RESET menu display

Part

Description

A

Menu title

B

Sub-menu title, see “RESET menu” on page 17

C

Parameter

Part

Description

A

Variable type

B

measured values/data

C

unit of measurement

Note: for the “power factor” the unit indicates whether the

value is inductive (L) or capacitive (C)

D

information and diagnostics

Information and warnings

Symbol

Description

Alarm icon:

• blinking icon + ALARM ON: alarm active

• steadily ON icon + WIRING: wiring error

Serial or optical communication state (reception / transmission)

Virtual wiring correction: the terminal-phase association was modified by UCS

10 WM15 - User manual | CARLO GAVAZZI Controls SpAWM15 - User manual | CARLO GAVAZZI Controls SpA

Commissioning

Preliminary settings

At switch-on, the device displays three preliminary setting menus:

• MID SETTINGS, for MID models only

• QUICK SETUP

• CHECK WIRING

MID SETTINGS menu

This procedure, only available in MID models, allows to program the current transformer ratio (CT ratio).

11WM15 - User manual | CARLO GAVAZZI Controls SpAWM15 - User manual | CARLO GAVAZZI Controls SpA

Commissioning

QUICK SETUP menu

This procedure is available when the instrument is switched on for the first time.

Note: the available parameters depend on the model.

In the “QUICK SETUP?” starting page

Select... To...

YES run the QUICK SETUP procedure

NO skip the procedure and no longer display the QUICK SETUP menu

NEXT TIME skip the procedure and display the QUICK SETUP menu at the next switch-on

WM15 - User manual | CARLO GAVAZZI Controls SpA12 WM15 - User manual | CARLO GAVAZZI Controls SpA

Commissioning

WIRING CHECK menu

This procedure is available if the set system is 3P+N, and allows to check and correct the connections, see “WIRING CHECK

function” on page 21.

In the “CHECK WIRING?” starting page

Select... To...

YES run the WIRING CHECK procedure

NO skip the procedure and no longer display the WIRING CHECK menu

NEXT TIME skip the procedure and display the WIRING CHECK menu at the next switch-on

In the “SHOW AGAIN?” end page

Select... To... And...

YES

correct the error detected by WM15.

Actions:

• switch off the instrument

• correct the wiring (follow the graphical indications)

display the WIRING CHECK menu again for the

final check

NO

No longer display the menu (WM15 has detected no wiring

errors)

-

13

WM15 use

WM15 - User manual | CARLO GAVAZZI Controls SpAWM15 - User manual | CARLO GAVAZZI Controls SpA

Working with WM15

Working with the measurement pages

Operation

Button

Return to the Home page

Scroll through the pages

/

Enter the Main menu

Working with the SETTINGS menu

Operation

Button

Return/Cancel the operation

Scroll through the menu, edit the parameters

/

Enter the sub-menu to edit and confirm the operation

Working with the INFO menu

Operation

Button

Return to the main menu

Scroll through the menu

/

Working with the RESET menu

Operation

Button

Return/Cancel the operation

Scroll through the menu

/

Enter the sub-menu to edit and confirm the operation

14

WM15 use

WM15 - User manual | CARLO GAVAZZI Controls SpA

Menu description

Measurement pages

The displayed pages depend on the selected system.

Page Displayed measurements Description

1

TOT kWh

kW

PF

Imported active energy (TOTAL)

System active power

System power factor

2

TOT kWh

TOT kvarh+

TOT kvarh-

Imported active energy (TOTAL)

Imported reactive energy (TOTAL)

Exported reactive energy (TOTAL)

3

TOT kWh

TOT kVAh

TOT hh:mm+

Imported active energy (TOTAL)

Apparent energy (TOTAL)

Positive energy run hour meter* (TOTAL)

*NOTE: it increases when the active system power is positive.

4

kWh- TOT

kVAh TOT

h- TOT

Exported active energy (TOTAL)

Apparent energy (TOTAL)

Negative energy run hour meter* (TOTAL)

*NOTE: it increases when the active system power is negative.

5

L1 kWh

L2 kWh

L3 kWh

Active energy phase 1

Active energy phase 2

Active energy phase 3

6

PAR kWh

kW sys

PF sys

Imported active energy (PARTIAL)

System active power

System power factor

7

PAR kWh

PAR kvarh+

PAR kvarh-

Imported active energy (PARTIAL)

Imported reactive energy (PARTIAL)

Exported reactive energy (PARTIAL)

8

PAR kWh+

PAR kVAh

PAR hh:mm+

Imported active energy (PARTIAL)

Apparent energy (PARTIAL)

Positive energy run hour meter* (PARTIAL)

*NOTE: it increases when the active system power is positive.

9

PAR kWh-

PAR kVAh

PAR hh:mm-

Exported active energy (PARTIAL)

Apparent energy (PARTIAL)

Negative energy run hour meter* (PARTIAL)

*NOTE: it increases when the active system power is negative.

10

kW

kvar

kVA

System active power

System reactive power

System apparent power

11

kW

kW DMD

kW DMD MAX

System active power

System active power DMD

System active power MAX DMD

12

kVA sys

kVA sys DMD

kVA sys DMD max

System apparent power

System apparent power DMD

System apparent power MAX DMD

13

L1 kW

L2 kW

L3 kW

Phase 1 active power

Phase 2 active power

Phase 3 active power

14

L1 kvar

L2 kvar

L3 kvar

Phase 1 reactive power

Phase 2 reactive power

Phase 3 reactive power

15

L1 kVA

L2 kVA

L3 kVA

Phase 1 apparent power

Phase 2 apparent power

Phase 3 apparent power

16

L1 PF

L2 PF

L3 PF

Phase 1 power factor

Phase 2 power factor

Phase 3 power factor

17

L-N V

L-L V

Hz

System line-neutral voltage

System line-line voltage

Frequency

15

WM15 use

WM15 - User manual | CARLO GAVAZZI Controls SpA

Note: pages 1, 10, 13, 16, 17, 21, 22 and 26 are included in the default filter; see “Page filter” on page 20

18

L1 A

L2 A

L3 A

Phase 1 current

Phase 2 current

Phase 3 current

19

L1 A DMD

L2 A DMD

L3 A DMD

Phase 1 DMD current

Phase 2 DMD current

Phase 3 DMD current

20

L1 A DMD max

L2 A DMD max

L3 A DMD max

Phase 1 current DMD MAX

Phase 2 current DMD MAX

Phase 3 current DMD MAX

21

L1-N V

L2-N V

L3-N V

Phase 1 voltage

Phase 2 voltage

Phase 3 voltage

22

L1-2 V

L2-3 V

L3-1 V

Phase 1-phase 2 voltage

Phase 2-phase 3 voltage

Phase 3-phase 1 voltage

23

L1-N THD V %

L2-N THD V %

L3-N THD V %

THD of phase 1 voltage

THD of phase 2 voltage

THD of phase 3 voltage

24

L1-2 THD V %

L2-3 THD V %

L3-1 THD V %

THD of phase 1-phase2 voltage

THD of phase2-phase3 voltage

THD of phase3-phase1 voltage

25

L1 THD I %

L2 THD I %

L3 THD I %

THD of phase 1 current

THD of phase 2 current

THD of phase 3 current

26

V L-L sys

L1 A

L2 A

L3 A

System Phase-phase voltage

Phase 1 current (bar graph)

Phase 2 current (bar graph)

Phase 3 current (bar graph)

16

WM15 use

WM15 - User manual | CARLO GAVAZZI Controls SpA

SETTINGS menu

This menu allows to set the parameters.

Page title Sub-menu Description Values Default values

SYSTEM - System 3P+N

3P

2P

1P

3P+N

CT RATIO - (CT) current transformer ratio 1.0 to 2000 1.0

DMD INTERVAL - dmd interval 1 to 60 min 15 min

RS485 ADDRESS Address 1 to 247 1

BAUDRATE Baudrate 9.6 to 115.2 kbps 9.6 kbps

PARITY Parity NO/EVEN NO

ALARM ENABLE Enable YES/NO NO

VARIABLE Monitored variable kW

kVA

kvar

PF

A

V L-N

V L-L

kW

SET POINT 1 Activation threshold -15000 to 15000 0.00

SET POINT 2 Deactivation threshold -15000 to 15000 0.00

ACTIVATION DELAY Activation delay 0 to 3600 s 0

DIGITAL OUTPUT FUNCTION Function DISABLED

ALARM

PULSE

DISABLED

OUTPUT STATUS

(ALARM)

Output state NO (normally open)

NC (normally closed)

NO

PULSE WEIGHT Pulses weight 0.001 to 10 kWh/pulse 1

PULSE DURATION Pulse duration 30/100 ms 30 ms

DISPLAY BACKLIGHT TIME Timer for backlight switch-off ALWAYS ON

1 min

2 min

5 min

10 min

20 min

30 min

60 min

ALWAYS ON

SCREENSAVER Screensaver enabling, see

“Screensaver” on page 20

ON/OFF ON

PAGE FILTER Measurement page lter

enabling, see “Page lter” on

page 20

ON/OFF OFF

WIRING CHECK Icon enabling ON/OFF ON

PASSWORD Password enabling for the

SETTINGS and RESET menu

0000 (not protected) to 9999 0000 (NOT PROTECTED)

EXIT - Exit - -

17

WM15 use

WM15 - User manual | CARLO GAVAZZI Controls SpA

INFO menu

This menu allows to display the set parameters.

Page Page title Description

1 WIRING CHECK Display of wiring check icon enabled/disabled

2 SYSTEM System type

3 CT RATIO (CT) current transformer ratio

4 LED PULSE Pulses weight

5 DMD INTERVAL dmd interval

6 RS485 Address, baudrate, parity

7 ALARM Alarm function

8 DIGITAL OUTPUT Digital output function

9 DISPLAY Backlight, screensaver, page lter and WIRING CHECK function

10 V CONNECTIONS Terminal- phase association for voltage inputs

11 I CONNECTIONS Terminal-phase association for current inputs

12 CHECKSUM FW Checksum for MID certification

13 SERIAL NUMBER Serial number

14 SECONDARY ADDR M-Bus secondary address for use with VMU-B

RESET menu

This menu allows to reset the following settings:

Page Page title Description

1 PARTIAL It resets the partial meters

2 DMD AND MAX It resets the dmd calculation

3 FACTORY RESET It restores the factory settings

18

Essential information

WM15 - User manual | CARLO GAVAZZI Controls SpA

Essential information

Alarms

Introduction

WM15 manages a measured variable alarm. To set the alarm, define:

• the variable to be monitored (VARIABLE)

• alarm activation threshold value (SET POINT 1)

• alarm deactivation threshold value (SET POINT 2)

• alarm activation delay (ACTIVATION DELAY)

Variables

The unit can monitor one of the following variables:

• system active power

• system apparent power

• system reactive power

• system power factor

• phase-neutral voltage (OR logic)

• phase-phase voltage (OR logic)

• current (OR logic)

Note: if you select a current or a voltage, WM15 simultaneously monitors all the phases available in the set measurement system and triggers

the alarm when at least one of the phases is in alarm (OR logic)

Alarm types

Up alarm (Set point 1 ≥ Set point 2)

The alarm activates when the monitored variable exceeds the Set 1 value for a time equal to the activation delay (Delay) and deactivates

when the values drops below Set 2.

(s)

ON

Set 1

Set 2

Delay

19

Essential information

WM15 - User manual | CARLO GAVAZZI Controls SpA

Down alarm (Set point 1 < Set point 2)

The alarm activates when the monitored variable drops below the Set 1 value for a time equal to the activation delay (Delay) and deactivates

when it exceeds Set 2.

(s)

ON

Set 2

Set 1

Delay

Digital output

The digital output can perform two functions:

Function Description Parameters

Alarm Output associated with the alarm Output state when no alarm is active

Pulse output Pulse transmission output for imported active energy consumptions.

• Pulse weight

• Pulse duration

dmd values

Average value calculation (dmd)

WM15 calculates the average values of the electrical variables within a set integration interval (15 min by default).

Integration interval

The integration interval starts at switch-on or when the reset command is issued. The first value is displayed at the end of the first integration

interval.

Example

The following is a sample integration:

• reset at 10:13:07

• set integration time: 15 min.

The first value displayed at 10:28:07 refers to the interval from 10:13:07 to 10:28:07.

Optical port and OptoProg

The optical port allows to set up the WM15 unit and to read the data through UCS (from PC) or mobile UCS (da smartphone Android) without

connecting to the RS485 network to which the analyser is connected. You need to purchase OptoProg, the Carlo Gavazzi optical interface

device for communication via micro USB or via Bluetooth.

20

Essential information

WM15 - User manual | CARLO GAVAZZI Controls SpA

LCD display

Home page

The unit may display the default measurement pages when the Home button is pressed (starting from any measurement page) or after no

operation has been performed for five minutes, if the screensaver is enabled and the screensaver type is set by UCS to “Home page” (default

value).

Notes: if you select a page that is not available in the set system, the unit displays as its home page the first available page. In MID models the

home page cannot be changed and displays the active energy meter.

Backlight

The WM15 unit is equipped with a backlight system. You can set whether the backlight shall always be ON or whether it should automatically

switch off after a given interval has elapsed since a button was pressed (1 to 60 minutes).

Screensaver

If the SCREENSAVER function is enabled (default setting), after 5 minutes have elapsed since a button was pressed the unit will display the

home page if the screensaver type is “Home page” (default setting), or it shall activate the slideshow function, which displays the selected

pages on a rotating basis

Notes: the screensaver type and the slideshow function with the relevant pages can only be set up through the UCS software or the UCS

Mobile app. In MID models the screensaver setting is “Homepage” and cannot be changed.

Page lter

The page filter makes it easier to use and browse the measurement pages. When you use the / buttons, the unit shall only display

the pages you are most interested in, which can be selected through the UCS software or the UCS Mobile app.

Note: to display all the pages without using the UCS software or app, you can disable the page filter from the SETTINGS MENU (DISPLAY →

PAGE FILTER → OFF). By default, the pages included in the filter are: 1, 10, 13, 16, 17, 21, 22, 26, see “Measurement pages” on page 14.

Restoring the factory settings

Restoring the settings using the RESET menu

From the RESET menu you can restore all the factory settings. At start-up the QUICK SET-UP and WIRING CHECK menu shall be available

again.

Notes: meters are not reset. In MID models you cannot reset the CT current transformer ratio (CT RATIO).

Restoring the settings using the reset button

Press for at least five seconds the reset button (located near the current inputs) to access the menu, restore all the factory settings and reset

all meters (total and partial).

Note: in MID models the reset can only be performed if the energy meter has not exceeded 1 kWh. Before sealing the terminal, you can then

correct any CT current transformer setting errors (CT ratio), reactivating the MID programming menu at the next switch-on.

La page charge ...

CARLO GAVAZZI WM1596AV53XOSXKR Manuel utilisateur

Ce manuel convient également à

CARLO GAVAZZI WM1596AV53XOSXKR Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents