Marvel MA15CPS1LS Manuel utilisateur

Marque: Marvel

Modèle: MA15CPS1LS

Catégorie: Frigos

Taper: Manuel utilisateur

Outdoor Refrigerator / Freezer

Réfrigérateur / Congélateurs

d'extérieur

MO24RF

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

NOTE

CAUTION

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

CONTENTS

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration ......................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the water supply ...................................................6

Optional ice-maker operation ..............................................7

Product dimensions ...........................................................8

Starting your appliance ..................................................10

Using your Electronic control ............................................10

Sleep mode ...................................................................10

Turning your appliance "ON" or "OFF" ..........................11

Adjusting the temperature .............................................11

Temperature mode ........................................................11

Control lock ................................................................12

Temperature sensor error codes ................................12

Alarms ...........................................................................12

Door ajar ..................................................................12

Power failure .............................................................13

Temperature alarm ....................................................13

Vacation mode ..................................................................13



Shelf removal ...................................................................15

Care and cleaning .............................................................16

Long term storage/winterization ...................................16

Energy saving tips ............................................................19

Stainless steel maintenance .............................................20

Obtaining service .............................................................20

Troubleshooting .................................................................21

Troubleshooting ice-maker ..............................................22

Warranty ...........................................................................23

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

Death or serious injury could result if...

NOTE

CAUTION

XXXXXXXXXXXX

MARVEL

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Warranty Registration

UNPACKING YOUR APPLIANCE

Online registra-

tion available at

www.marvelrefrig-

eration.com

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.marvelrefrigeration.com.

The following information will

be required when registering

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the right

side near the top. (See Figure 1).

Figure 1

WARNING

WARNING - Help Prevent Tragedies



the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• 

• Leave the shelves in place so children may not

easily climb inside.

WARNING

WARNING - Dispose of the plastic bags which can



CAUTION

INSTALLING YOUR APPLIANCE

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

-

mended installation location temperature range is from 55

to 115°F (13 to 46°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unobstruct-

ed.

Front Grille

Do not obstruct the front grille. The openings within the

-



energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean. Marvel does not recommend the use



Figure 2).

Rear

Leveling

Legs

Figure 2

Front Leveling

Legs

Front Grille,

keep this area

open.

Leveling Legs

Adjustable legs at the front and rear corners of the appli-



-

all height of your Marvel appliance may be adjusted be-

tween the minimum, 33

4" (85.7 cm), by turning the leveling

leg in (CW ↷) and the maximum, 34

4" (88.3 cm) by turning

the leveling leg out (CCW ↶).

To adjust the leveling legs, place the appliance on a solid





lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

NOTE

Figure 3

Figure 4

Do not remove

ground prong

INSTALLING YOUR APPLIANCE

Front grille

Front grille screw

Figure 5

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4 ).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

WARNING

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Figure 6

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Figure 7a

• -

tings.

• Reverse osmosis, softened water, and de-ionized water



quality of the ice.

Water

Supply

Line

service

loop

Figure 7

Back view of

ice machine

NOTE

CAUTION

Water line from water valve

to ice-maker

INSTALLING THE WATER SUPPLY

MODEL MO24RF WITH OPTIONAL ICE-MAKER KIT

An optional ice-maker kit (part number S42418151) is avail-

able for model MO24RF which includes all of the necessary

parts for installation. The kit can be obtained from Marvel

customer service by calling 800-223-3900.

Water Supply

Observe and follow all local building codes when installing

this appliance.

Use

" copper tubing for your water supply which is avail-

able at any local hardware or plumbing supply store. Bend

the

" copper tubing to suit your installation being sure not

to kink the tubing. Purchase enough copper tubing length

and coil it behind the unit to form a "service loop" which will

allow the appliance to be pulled out from the installation for

servicing or cleaning. Connect the copper tubing to the "top

side" of a cold water pipe to prevent the ice-maker from

plugging with sediment.



ease servicing the appliance. NOTE: A SELF-PIERCING

TYPE VALVE IS NOT RECOMMENDED as they are prone

to clogging with sediment which will create pressure drop

reducing the water supply to the unit.

Connect the copper tubing water supply to the brass union



Water pressure must be at a minimum of 20 psi for proper

operation and a maximum of 120 psi.

Make certain all water connections are watertight after in-

stallation. Form the tubing so that it will not vibrate against

the cabinet body or kink when your appliance is set in posi-

tion.

Brass union for

4" copper tubing

Connect water

supply here

NOTE

Ice-maker operation

• The unit must be installed level for proper ice-maker

operation.

• -

tion for the ice-maker to operate. (See Figure 8).

• When the freezer section and ice-maker unit has suf-



automatically.

• When the ice bucket is full, the ice-maker will automati-



• You may manually stop the ice-maker by raising the

-

tion. (See Figure 8).

Arm down, ice-maker

will operate

Arm up, stops operation

Figure 8

OPTIONAL ICE-MAKER OPERATION

CAUTION

The water supply to the ice-maker must be turned on prior

to turning the ice-maker on. Failure to do so will cause

rapid dry cycling of the ice-maker mold heater resulting in

temperature control issues in the freezer compartment.

-

ing the bucket, or ice may be dispensed onto the freezer



If the ice is not used regularly, it will clump together with

time. For best ice results, discard ice in the bin as required

and allow the ice-maker to make a new fresh batch of ice.



removing the bucket.

"A"

"B"

"C"

"D"

"E"

PRODUCT DIMENSIONS

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

MO24RFS

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

8"

(60.7 cm)

4" to 34

4"

(85.7 to 88.3 cm)

32"

(60.2 cm)

32"

(66.6 cm)

32"

(117.9 cm)

4"

(66.7 cm)

DOOR STYLE

(S) Solid Door

Figure 9

Figure 9a

Figure 10

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 10).

"F"

"D"

"E"

"H"

"J"

"G"

8"

(1.6 cm)

PRODUCT DIMENSIONS

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

MO24RFS 115V/60Hz/15A

140 lbs

(63.6 kg)

* Depth dimension of rough-in opening may vary depending

on each individual installation. To recess entire door "F" di-

mension plus 1" (2.5 cm) for thickness of power cord plug.

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

Figure 11

2"

(54.6cm)

Power Failure

ALARM RESET

Compartment

select

REF

FRZ

Figure 12

Using your electronic control:

The sleep mode can be disabled if you prefer to have the

display on continuously. Press and hold the "Lock" key-

pad until the display goes past "Loc" and reads "nSL". To

enable the sleep mode, repeat the instruction, again going

past "Loc" until the display reads "SLP".



sound, and the current storage compartment temperature

will be displayed.

Sleep mode:

If no keypads are pressed for 60 seconds, the display will

enter sleep mode to conserve power. The control panel will

go dark with the exception of the system status "OK" indi-

cator which will remain enabled. Alarm conditions will wake

the display, (see alarms on page 12).

Starting your appliance:

Plug the appliance power cord into a 115 volt wall outlet.

Your appliance is shipped from the factory in the "On" posi-

tion and will begin start-up of cooling as soon as power is



wall outlet has power, and that the control is in the "On"







On initial power up, the control display will indicate a

"Power Failure" alarm. This is a normal condition as the ap-

pliance was powered-up at the factory for quality inspection

and then removed from power. A momentary press of the



section on page 12).

STARTING YOUR APPLIANCE

Figure 12a

Electronic control

Temp

Minus

keypad

Temp

Plus

keypad

On/O

keypad

Display Area

Lock

keypad

System Status

indicators

NOTE

To make the following changes to the control settings

(turning the appliance ON/OFF, adjusting the tempera-

ture, and activating vacation mode), the control must

be awake.

Your product has an automatic defrost feature that utilizes

an electric heater element. Periodically during defrost you

may observe the following:

• Water dripping and running sounds as a result of the

frost melt

• Sizzling and popping sounds from water dripping on

the heater element

• A faint reddish glow in the freezer compartment from

the electric heater element

These are all “normal” operating characteristics related to

refrigeration product incorporating automatic defrost. They

do not represent any product fault or safety issue.

warmer respectively. When you have reached your desired



or do nothing and the "Set" mode will time-out in 10-sec-

onds accepting the displayed temperature as the new

set-point.

The available set-point temperature range for your appli-

ance is -6°F (-21°C) to 6°F (-14°C) for the freezer com-

partment (ice-maker) and 34°F (1.2°C) to 42°F (5.7°C) for

the refrigerator compartment. If you attempt to adjust the

temperature outside of these ranges you will receive an



Freezer

compartment

selected

Refrigerator

compartment

selected

REF

FRZ

REF

FRZ

Temperatures can be set for each individual compartment



select the compartment you want to set the temperature for.

You do so by pressing the refrigerator (REF) or freezer

(FRZ) button on the display. When pressed the LED light

will be illuminated for the respective display.

To change the set temperature for a particular compart-

ment, with the compartment enabled and out of sleep

mode, press the "-" or "+" keypads. "SET" will be indi-

cated on the user interface panel and the current set-point



the "-" or "+" keypads will adjust the temperature colder or

Adjusting the temperature:

When making temperature set-point changes, it may take

up to 24-hours for the stored contents to stabilize at your

new set-point temperature.



temperature:

• Changes to temperature setting.

• Room temperature changes.

• Temperature of stored contents.

- Loading warm contents.

- Cold content load will delay the change to a warmer

set-point temperature.

- Warm content load will delay the change to a colder

set-point temperature.

• Usage, (number and duration of the door openings).

• Installation of the appliance in direct sunlight or next to

a heat source.

Turning your appliance ON and OFF:

If the appliance is "On", (and out of sleep mode) the tem-

perature will be shown in the display area of the control.



keypad for 4-seconds. "OFF" will now be displayed on the

control.



keypad for 4-seconds.

USING YOUR ELECTRONIC CONTROL

Temperature mode:

The temperature mode is preset from the factory in Fahren-

heit (°F) but you have the option to change it to Centigrade

(°C). To change the mode, press and hold the "-" keypad,

while pressing the "+" keypad, then release the "-" keypad.

The temperature will now be displayed in Centigrade (°C).

Repeat the procedure to change the temperature mode

back to Fahrenheit (°F).

NOTE

Loading warm contents may trigger a temperature alarm,

see temperature alarm page 13. Depending on the quantity

and/or weight of warm contents, it may take 48 hours for

the compartment temperature to stabilize.

Temperature Sensor Error Codes

Sensor Displayed Code Error Description Action to Take

Refrigerator

Temperature

Sensor

Failed temperature sensor in the

refrigerator compartment. Can lead to

unwanted storage temperatures and/or

spoiled perishable goods.

Call service to have the

temperature sensor replaced and

remove all perishable goods from com-

partment to prevent spoilage.

Freezer

Temperature

Sensor

Failed temperature sensor in the

freezer compartment. Can lead to

unwanted storage temperatures and/or

spoiled perishable goods.

Call service to have the

temperature sensor replaced and

remove all perishable goods from com-

partment to prevent spoilage.

Defrost Sensor

Failed defrost temperature sensor.

Causes unit to not defrost properly and

can create large frost build-up. Can lead

to water damage to the unit and sur-



Unplug the power cord

immediately and call service to have

the defrost sensor replaced.

Door Ajar

ALARM RESET

USING YOUR ELECTRONIC CONTROL

Alarms:

The control will alert you to conditions that could adversely



• Door ajar - If the door is open, or not closed prop-

erly, for more than 5-minutes the System Status OK



and a tone will sound every 60 seconds. Additionally,

an "ALARM RESET" indicator will be displayed below



The temperature sensors are monitored continuously. Any

OPEN or SHORTED circuit condition will initiate an

ERROR CODE as listed below:

Temperature Sensor Error Codes

Control lock:

The control panel can be locked to avoid unintentional

changes. To lock the control, press and hold the "Lock" key-

pad until the display reads "Loc" then immediately release



and then continuously illuminate. When the control panel is

locked, only the Lock keypad, System Status OK indicator

, and the Alarm indicator are active. To un-lock the control

panel, repeat this instruction until the display reads "nLc"



NOTE

If the control lock is active (illuminated lock icon) the

control will have to be unlocked before using the

keypad to reset an alarm condition. See page 12

(Control Lock) for instructions for unlocking the control.

This alarm condition can be reset by closing the door or



are cleaning the storage compartment, etc.). The alarm

will recur in 5-minutes if the alarm condition persists.

NOTE

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

ALARM RESET

Power Failure

ALARM RESET

Temp

NOTE

Door Ajar

Temp

• Power failure - If power to the appliance is inter-





"ALARM RESET" indicator will be displayed below the



condition can be reset by momentarily pressing the

-

ed that you check the condition of any perishables,

even if the appliance is operating normally and the tem-

perature has recovered, as prolonged power outages

could result in excessive temperature excursions which

may spoil perishables.

• Temperature alarm - If the storage compart-

ment temperature deviates excessively from your

set-point temperature for an extended period of time,



will sound every 60 seconds. Additionally, an "ALARM

RESET" indicator will be displayed below the "ON/

OFF" keypad.

Multiple alarms are possible, i.e.- "Door Ajar" for a pro-

longed period may trigger a "Temp" alarm, in which case

both "Door Ajar" and "Temp" indicators will activate.

Vacation mode:

This operating mode can be used to save energy during

high cost energy periods, or when you won't be using your

appliance for an extended period of time by disabling the

lights, alarm tones, and keypad entry tones. Vacation mode

also serves as a Sabbath mode, disabling functions and

its controls in accordance with the weekly Sabbath and

religious holidays observed within the Orthodox Jewish

community. When used as Sabbath mode, you may open

or close the door at any time to access contents without

-

outs, solenoids, fans, valves, compressor, icons, tones, or

alarms.

When activated, the display, alarm indicators and tones,

keypad touch tones, interior lights, and all options are dis-

abled. All keypad functions are disabled, with the exception

-

mode. Storage compartment temperatures are monitored

and controlled at the settings prior to entering Vacation

mode.

To enter Vacation Mode (with the control out of sleep





"VAC" 3-times to acknowledge your request, then will

display "VAC" continuously until Vacation mode is exited.

A power outage will not exit Vacation mode, exiting can

only be accomplished manually. To exit Vacation mode and



keypad until the control displays the temperature.

USING YOUR ELECTRONIC CONTROL

NOTE

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

This alarm condition can be reset by momentarily pressing



that you check the condition of your stored contents, even

though the appliance is operating normally and the temper-

ature has recovered, as prolonged temperature excursions

could spoil perishables.

NOTE

After a high temperature alarm condition, check all perish-

ables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage compart-

ment. If the temperature alarm continues to occur, your unit

may require service.

SHELVING CONFIGURATIONS

Refrigerator / Freezer

24" (61 cm) wide see Figure 13:

Refrigerator:

(2) Half width cantilever adjustable shelf.

see Figure 14

 

(1) Roller glide clear crisper drawer

Freezer:

(1) Fixed position metal shelf, see Figure 15.

Figure 13

To remove the crisper :

Pull out until it stops. Lift up on the front of the pan, and

remove it from the frame.

Figure 14

Freezer

compartment

Figure 15

Freezer shelf

Figure 16

SHELF REMOVAL

To Add or Remove a Shelf

Remove stored product from the shelf. Do not try to remove

a loaded shelf from the appliance. Grasp the shelf front with

both hands, rotate the front upward and lift out. (See Figure

17a). To install a shelf insert the shelf in the appliance and

insert the top hooks into the shelf support slots and drop

the shelf down so the hooks drop over the bottom of the

slots.

Make sure your cantilever shelf is secure on the shelf sup-

ports by pressing down on the shelf before loading.

CAUTION

Never try to move a loaded shelf, remove everything from

the shelf before moving. Use both hands when moving the

shelf.

Grasp the shelf

by the front with both

hands and rotate the

front of the shelf up,

then lift the shelf up

and remove the shelf

from the shelf ladders.

Figure 17

Figure 17a

CAUTION

CARE AND CLEANING

Front Grille

-

ings in front of the cabinet. At least once or twice a year,

brush or vacuum lint and dirt from the front grille area (see

page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap

and water and thoroughly rinsed with clear water. NEVER

use abrasive scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop-

ping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

4. Periodically check and/or clean the front grille as

needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of door openings while the



temperature.

Light assembly replacement

All models use LED lamps to illuminate the interior of the

appliance. This component is very reliable, but should one



of the LED.

Outdoor Product Long-Term Storage / Winter-

ization: (MO24RF, refrigerator freezer):

1. Time to Winterize, when the daily low ambient tempera-

ture is at or below 38°F (3.3°C).

CAUTION

Operation of the unit at ambient temperatures below the

recommended Winterization temperature will void your war-

ranty.

2. 

3. Remove all contents.

4. If necessary, move the unit so you can gain access to

the rear of the product.

5. Unplug the unit from the power outlet.

6. It is also recommended that the power to the outlet be



during the Winter season.

7. When cleaning unit pay particular attention to any

cracks and crevices that may have accumulated dirt

and debris.

8. Remove the front toe-grille, (see Figure 18), and use a

brush and vacuum to clean dirt and debris from be-

neath the unit.

9. Thoroughly clean the toe-grille and re-install on the

unit. (See Figure 18).

10. Remove the rear access cover, (see Figure 19), and

use a brush and vacuum to clean dirt and debris from

the machine compartment.

11. Thoroughly clean the rear access cover and re-install

on the unit.

12. Wipe down all interior surfaces with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals which could cause staining. Do

not use any abrasive cleaners or scouring pads.

13. Leave the door open and allow to completely dry out

before closing the door.

14. Thoroughly clean the door gasket with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals.

15. Thoroughly clean the exterior with a cleaner approved

for stainless steel. Do not use any abrasive cleaners or

scouring pads. See "Stainless Steel Maintenance" on

page 20.

16. Any mounting hardware / fasteners that are showing

signs of corrosion should be replaced.

17. Once the exterior has been thoroughly cleaned, you

may want to apply a coating of car wax to help protect

against spotting from moisture, dirt, and debris that

may accumulate on the surfaces during the Winteriza-

tion period.

• If the plastic defrost drain pan located under the

compressor contains water, use a sponge to

remove as much water as possible.

CARE AND CLEANING

Start-Up After Long-Term Storage:

1. If stored outside, it is recommended that the unit again

be thoroughly inspected per the storage instructions

above to address any dirt or debris from the weather

and/or animals/insects.

2. Connect the unit to electrical power.

3. 

4. Allow 24-hrs for the unit to stabilize before loading

contents.

Figure 18

Grille

Spacer

Clean out

behind

grille

Figure 19

Soak up

water from

plastic drain

pan if

necessary

Clean out

debris

Remove screws

around perimeter

of access cover.

18. Do not place a cover on the unit, as this can trap con-

densation.

After completion of the above, you may choose to store the

unit indoors, although this is not required.

Remove screw from

each end of grille

Access cover

CAUTION

Operation of the unit at ambient temperatures below the

recommended Winterization temperature will void your war-

ranty.

2. Raise the bail arm of the ice maker ( see Figure 8 on

page 7) to stop ice production.

3. 

4. If necessary, move the unit so you can gain access to

the rear of the product.

5. 

valve located on the back of the unit, (see page 6).

6. Be sure the exterior water supply line is drained or

blown out to prevent freezing and cracking of the sup-

ply line.

7. We recommend a cap be placed on the water supply

line to prevent dirt and insects from plugging the line.

8. Empty the ice bucket and replace the ice bucket in unit.

9. Lower the ice maker bail arm to allow the unit to oper-

ate until ice is dispensed from ice maker to empty the

ice maker mold.

10. Raise the bail arm and remove the ice bucket and

clean thoroughly with warm water and dish soap.

11. 

page 11).

12. Unplug the unit from the power outlet.

13. It is also recommended that the power to the outlet is



during the winter season.

14. When cleaning the unit pay particular attention to any

cracks and crevices that may have accumulated dirt

and debris.

15. Remove the front toe-grille, (see Figure 20), and use a

brush and vacuum to clean dirt and debris from be-

neath the unit.

16. Thoroughly clean the toe-grille and re-install on the

unit. (See Figure 20).

17. Remove the solenoid cover and 3 screws. (see Figure

21). Remove the rear access cover, (see Figure 21),

and use a brush and vacuum to clean dirt and debris

from the machine compartment.

18. Disconnect the plastic water line from the bottom of the

solenoid valve (see Figure 21a) and drain. Reconnect

the water line.

Outdoor Product Long-Term Storage / Winter-

ization: (MO24RF, with optional ice maker):

1. Time to Winterize, when the daily low ambient tempera-

ture is at or below 38°F (3.3°C).

CARE AND CLEANING

Figure 20

Grille

Spacer

Clean out

behind

grille

Remove screw from

each end of grille

19. Thoroughly clean the rear access cover and re-install

on the unit.

20. Wipe down all interior surfaces with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals which could cause staining. Do

not use any abrasive cleaners or scouring pads.

21. Leave the door open and allow to completely dry out

before closing the door.

22. Thoroughly clean the door gasket with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals.

23. Thoroughly clean the exterior with a cleaner approved

for stainless steel. Do not use any abrasive cleaners or

scouring pads. See "Stainless Steel Maintenance" on

page 20.

24. Any mounting hardware / fasteners that are showing

signs of corrosion should be replaced.

25. Once the exterior has been thoroughly cleaned, you

may want to apply a coating of car wax to help protect

against spotting from moisture, dirt, and debris that

may accumulate on the surfaces during the Winteriza-

tion period.

• If the plastic defrost drain pan located under the

compressor contains water, use a sponge to

remove as much water as possible.

CAUTION

The water supply to the ice-maker must be turned on prior

to turning the ice-maker on. Failure to do so will cause

rapid dry cycling of the ice-maker mold heater resulting in

temperature control issues in the freezer compartment.

CARE AND CLEANING AND ENERGY SAVING TIPS

Figure 21

Clean out

debris

Remove screws

around perimeter

of access cover.

Soak up

water from

plastic drain

pan if

necessary

Access cover

Solenoid

cover and

3 screws

To disconnect the water outlet line: Push up on the white

collar and pull the plastic water line from the bottom of the

water valve.

To reconnect the water outlet line: Simply insert the plas-

tic tubing into the white collar and push until it stops (about

2", 12 mm, of water line will enter the valve).

White

collar

Plastic outlet

water line

Figure 21a

Start-Up After Long-Term Storage:

1. If stored outside, it is recommended that the unit again

be thoroughly inspected per the storage instructions

above to address any dirt or debris from the weather

and/or animals/insects.

2. Connect the unit to electrical power and the water sup-

ply.

3. 

4. Allow 24-hrs for the unit to stabilize before loading

contents.

The following suggestions will minimize the

cost of operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance

(cooker, dishwasher, etc.), heating air duct, or other

heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance be-

neath door are not obstructed and kept clean to allow

ventilation for the refrigeration system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize door

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

Energy saving tips:

6. Maintaining a relatively full storage compartment will

require less appliance run time than an empty compart-

ment.

7. Ensure door closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before plac-

ing in product.

9. Minimize door openings and duration of door openings.

10. Use the warmest temperature control set temperature

that meets your personal preference and provides the

proper storage for your stored contents.

11. When on vacation or away from home for extended pe-

riods, set the appliance to warmest acceptable tem-

perature for the stored contents.



appliance requires the door to be open for an extended

period of time.

STAINLESS STEEL MAINTENANCE

OBTAINING SERVICE

Background

Stainless steel does not stain, corrode, or rust as easily as

ordinary steel, but it is not stain or corrosion proof. Stain-

less steels can discolor or corrode if not maintained prop-

erly.



amount of chromium present. It is this chromium that





surface can be damaged or contaminated, which may

result in discoloration, staining, or corrosion of the base

metal.

Care & Cleaning

Routine cleaning of the stainless steel surfaces will serve to

greatly extend the life of your product by removing contami-

nants. This is especially important in coastal areas which

can expose the stainless to severe contaminants such as

halide salts, (sodium chloride).

It is strongly recommended to periodically inspect and thor-

oughly clean crevices, weld points, under gaskets, rivets,

bolt heads, and any locations where small amounts of liquid

could collect, become stagnant, and concentrate contami-

nates. Additionally, any mounting hardware that is showing

signs of corrosion should be replaced.

Frequency of cleaning will depend upon the installation

location, environmental, and usage conditions.

Choosing a Cleaning Product

The choice of a proper cleaning product is ultimately that

of the consumer, and there are many products from which

to choose. Depending upon the type of cleaning and the

degree of contamination, some products are better than

others.



cleaning of most stainless steel products is to give the sur-

faces a brisk rubbing with a soft cloth soaked in warm water

and a gentle detergent, or mild mixture of ammonia. Rub-

bing should, to the extent possible, follow the polish lines of

the steel, and always insure thorough rinsing after cleaning.

Although some products are called "stainless steel clean-

ers," some may contain abrasives which could scratch the



and some many contain chlorine bleach which will dull,

tarnish or discolor the surface if not completely removed.

After the stainless surfaces have been thoroughly cleaned,

a good quality car wax may be applied to help maintain the



Stainless steel products should never be installed, or stored

in close proximity to chlorine chemicals.

Whichever cleaning product you chose, it should be used

in strict accordance with the instructions of the cleaner

manufacturer.

NOTE

If Service is Required:

• 

please contact your dealer or call Marvel Customer

Service at 800.223.3900 for directions on how to obtain

warranty coverage in your area.

• 

Marvel Customer Service can provide recommenda-

tions of service centers in your area. A listing of autho-

rized service centers is also available at www.marvelre-

frigeration.com under the service and support section.

• In all correspondence regarding service, be sure to

give the service number, serial number, and proof of

purchase.

• Try to have information or description of nature of the

problem, how long the appliance has been running, the

room temperature, and any additional information that

may be helpful in quickly solving the problem.

• Table "A" is provided for recording pertinent information

regarding your product for future reference.

For Your Records

Date of Purchase

Dealer’s name

Dealer’s Address

Dealer’s City

Dealer’s State

Dealer’s Zip Code

Appliance Serial Number

Appliance Service Number

Date Warranty Card Sent (Must

be within 10 days of purchase).

Table A

La page charge ...

Marvel MA15CPS1LS Manuel utilisateur

Marque: Marvel

Modèle: MA15CPS1LS

Catégorie: Frigos

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Marvel MA15CPS1LS User manual

Marvel MA15CPS1LS Manuel utilisateur

Marvel MA15CPS1LS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents