Frigidaire LMWC23626S Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire
OWNER'S MANUAL
FRENCH DOOR
REFRIGERATOR
Read this owner's manual thoroughly before operating the
appliance and keep it handy for reference at all times.
ENGLISH / ESPAÑOL / FRANÇAIS
LMWS27626* / LMWC23626*
MFL70761724
Rev.02_020620
www.lg.com
Copyright © 2019 - 2020 LG Electronics Inc. All Rights Reserved.
TABLE OF CONTENTS
2
3 SAFETY INSTRUCTIONS
3 READ ALL INSTRUCTIONS BEFORE USE
3 WARNING
6 CAUTION
7 PRODUCT OVERVIEW
7 Product Features
10 INSTALLATION
10 Before Installing
11 Choosing the Proper Location
13 Removing/Assembling the Handles
14 Removing/Assembling the Doors and Drawer
18 Connecting the Water Line
21 Leveling and Door Alignment
21 Turning on the Power
22 OPERATION
22 Before Use
23 Control Panel
24 Sabbath Mode
24 Water Dispenser
24 Automatic Icemaker
25 Storing Food
27 Humidity Controlled Crispers
28 Glide‘N’Serve
28 Refrigerator Shelves
29 Door Bins
29 Durabase
30 SMART FUNCTIONS
30 LG ThinQ Application
30 Smart Diagnosis™ Feature
31 MAINTENANCE
31 Cleaning
32 Water Filter
35 TROUBLESHOOTING
35 FAQs
36 Before Calling for Service
45 LIMITED WARRANTY
45 For USA
49 For Canada
3SAFETY INSTRUCTIONS
ENGLISH
SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Safety Messages
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
follow all safety messages.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,
and tell you what may happen if the instructions are not followed.
WARNING
WARNING
To reduce the risk of explosion, fire, death, electric shock, scalding or injury to persons when using this
product, follow basic precautions, including the following:
Installation
To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including
the use of long-sleeved gloves and safety glasses.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has
missing or broken parts, including a damaged cord or plug.
Only connect this product to a dedicated grounded electrical outlet rated for use with this product (115
V, 60 Hz, AC only). It is the user’s responsibility to replace a standard 2-prong wall outlet with a standard
3-prong wall outlet.
Do not use an outlet that can be turned off with a switch. Do not use an extension cord.
The appliance must be positioned for easy access to a power source.
When moving the refrigerator, be careful not to roll over or damage the power cord.
Contact an authorized service center when installing or relocating the refrigerator.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
Keep packing materials out of the reach of children. Packaging material can be dangerous for children.
There is a risk of suffocation.
Do not install the refrigerator in a damp or dusty place where insulation on electrical parts may
deteriorate.
Do not place the refrigerator in direct sunlight or expose it to the heat from heating appliances such as
stoves or heaters.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages
will follow the safety alert symbol and either the word WARNING or CAUTION.
These words mean:
WARNING
You may be killed or seriously injured if you do not follow instructions.
CAUTION
You may be injured or cause damage to the product if you do not follow instructions.
4 SAFETY INSTRUCTIONS
Do not bend or pinch the power cord excessively or place heavy objects on it.
Operation
This appliance is intended to be used in household and similar applications such as :
- staff kitchen areas in shops, offices and other working environments;
- farm houses and by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments;
- catering and similar non-retail applications.
This product is not to be used for special purposes such as the storage of medicine or test materials or
for use on ships, etc.
DO NOT allow children to climb, stand, or hang on the refrigerator doors or on the shelves in the
refrigerator. They could damage the refrigerator and seriously injure themselves.
Do not allow children to climb into the refrigerator. They could be trapped and suffocated.
Children should be supervised to ensure that they do not play with the refrigerator.
Keep fingers out of pinch point areas; clearances between the doors and cabinets are necessarily small.
Be careful closing doors when children are nearby.
Do not touch frozen food or the metal parts in the freezer compartment with wet or damp hands. Doing
so may cause frostbite.
Do not refreeze frozen food that has thawed completely. Doing so may result in a serious health hazard.
Do not use an adapter plug or plug the power plug into a multi-outlet extension cord.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
Do not operate the refrigerator or touch the power cord with wet hands.
Do not modify or extend the power cord.
Do not use an uncertified power outlet. Do not plug appliance into a damaged wall outlet.
Do not put hands, feet or other objects into the air vents or bottom of the refrigerator. Doing so could
result in personal injury or electric shock.
In the event of a gas leak (propane/LPG), ensure the area is adequately ventilated and contact an
authorized service center before resuming use. Do not touch the refrigerator or power cord of the
refrigerator.
Disconnect the power cord immediately and contact an authorized service center if there is a strange
noise, odor, or smoke coming from the appliance.
Do not use any fuse (such as copper, steel wire, etc.) other than a standard fuse.
Do not place or use an electrical appliance inside the refrigerator, unless it is of a type recommended by
the manufacturer.
Do not put animals inside the appliance.
Do not place heavy or fragile objects, liquid filled containers, combustible substances, or flammable
objects (such as candles and lamps) on the appliance.
Avoid contact with any moving parts of the ejector mechanism or with the heater that releases the ice
cubes.
If connected to a circuit protected by fuses, use time delay fuse.
Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
Do not use mechanical devices or other means to accelerate the defrosting process, other than those
recommended by the manufacturer.
Do not use electrical appliances inside the food storage compartments of the appliance, unless they are
of the type recommended by the manufacturer.
Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
5SAFETY INSTRUCTIONS
ENGLISH
DO NOT place fingers in the automatic icemaker when the refrigerator is plugged in.
When dispensing ice from the dispenser, do not use a fragile container.
Maintenance
Do not use a hair dryer to dry the inside of the refrigerator.
Do not light a candle to remove odors in the refrigerator.
In the event of a refrigerant leak, move flammable objects away from the refrigerator. Ensure the area is
adequately ventilated and contact an authorized service center.
Keep flammable materials and vapors, such as gasoline, away from the refrigerator.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Unplug the power plug before cleaning or repairing the refrigerator.
The refrigerator and freezer compartment lights are interior LED lighting, and service should be
performed by a qualified technician.
Unplug the power plug immediately in the event of a blackout or thunderstorm.
Turn the power off if water or dust penetrates into the refrigerator. Call a service agent.
Do not store glass containers or soda in the freezer compartment. Contents may expand when frozen,
break the container and cause injury.
Do not store, disassemble or repair the appliance yourself or allow unqualified personnel to do so.
Disposal
Junked or abandoned refrigerators are dangerous, even if they are sitting for only a few days. When
disposing of the refrigerator, remove the packing materials from the door or take off the doors but leave
the shelves in place so that children may not easily climb inside.
If disposing of a refrigerator, make sure the refrigerant and insulation foam are removed for proper
disposal by a qualified servicer. If you release the refrigerant or throw away the insulation foam, you
may be fined or imprisoned in accordance with the relevant environmental law. Insulation foam contains
flammable blowing gas.
When discarding the appliance, remove the door gasket while leaving the shelves and baskets in place,
and keep children away from the appliance.
Grounding Instructions
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check
with a qualified electrician or service personnel if you are in doubt whether the appliance is properly
grounded. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
Have a certified electrician check the wall outlet and wiring for proper grounding.
Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull straight
out from the outlet. Failure to do so may damage the power cord, resulting in a risk of fire and electric
shock.
6 SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Risk of Fire and Flammable Materials
CAUTION
CAUTION
To reduce the risk of minor or moderate injury to persons, malfunction, or damage to the product or
property when using this product, follow basic precautions, including the following:
Installation
Do not install the refrigerator where there may be a danger of the unit falling.
The refrigerator must be properly installed in accordance with the Installation Instructions.
Operation
Do not use aerosols near the refrigerator.
This appliance is intended to be used only in domestic and similar applications.
Do not strike or apply excessive force to any glass surface. Do not touch glass surfaces if they are
cracked or broken.
Do not overfill or pack items too tightly into door bins. Doing so may cause damage to the bin or
personal injury if items are removed with excessive force.
Do not hang on to or place heavy objects on the refrigerator’s dispenser.
Maintenance
Do not use strong detergents like wax or thinners for cleaning. Clean with a soft cloth.
Remove foreign objects (such as dust and water) off the prongs of the power plug and contact areas. Do
not use a wet or damp cloth when cleaning the plug.
Do not spray water directly on the inside or outside of the refrigerator.
Do not clean glass shelves or covers with warm water when they are cold. They may break if exposed to
sudden temperature changes.
This appliance contains a small amount of isobutane refrigerant (R600a), which is combustible.
When transporting and installing the appliance, care should be taken to ensure that no parts
of the refrigerating circuit are damaged. Refrigerant squirting out of the pipes could ignite or
cause an eye injury. If a leak is detected, avoid any naked flames or potential sources of
ignition and air the room in which the appliance is standing for several minutes.
In order to avoid the creation of a flammable gas air mixture if a leak in the refrigerating
circuit occurs, the size of the room in which the appliance may be sited depends on the
amount of refrigerant used. The room must be 10.8 square feet (1 square meter) in size for
every 8g of R600a refrigerant inside the appliance. The amount of refrigerant in your
particular appliance is shown on the identification plate inside the appliance. Never start up an
appliance showing any signs of damage. If in doubt, consult your dealer.
7PRODUCT OVERVIEW
ENGLISH
PRODUCT OVERVIEW
Product Features
The images in this guide may be different from the actual components and accessories, which are subject
to change by the manufacturer without prior notice for product improvement purposes.
Exterior
a Refrigerator
Fresh food compartment
b Freezer Handle
Opens the freezer drawer.
c Refrigerator Handle
Opens and closes the refrigerator door.
d LED Light
Lights up when the freezer door is opened.
e Freezer
Frozen food compartment
8 PRODUCT OVERVIEW
Interior
LMWS27626*
a LED Interior Lighting
Lights up the inside of the refrigerator.
b Water Filter
Purifies water.
c Water Dispenser
Dispenses purified water.
d Door Mullion
Prevents the cold air in the refrigerator from escaping when the doors are closed.
CAUTION
To reduce the risk of scratching the door or breaking the center door mullion, make sure that the folding
door mullion is folded in before closing the left-hand door.
The door alarm will sound every 30 seconds if the door remains open longer than one minute.
e Humidity Controlled Crisper
Helps vegetables and fruit to stay crisp and controls humidity.
f Fixed Door Bin
Stores chilled food or drinks.
g Auto-Closing Hinge
The refrigerator doors and freezer drawers close automatically when pushed slightly. (The door only
closes automatically when it is open at an angle of less than 30°.)
h Automatic Icemaker (Freezer)
Dispenses ice automatically.
9PRODUCT OVERVIEW
ENGLISH
i Control Panel
Sets the refrigerator and freezer temperatures.
j Modular Door Bin
Interchangeable bins can be arranged to suit storage needs.
k Adjustable Refrigerator Shelf
The refrigerator shelves are adjustable to meet individual storage needs.
l Glide'N'Serve
Stores food items at a different temperature than the regular refrigerator area.
m Ice Bin
Stores ice from the freezer icemaker.
n Durabase and Durabase Divider
Provides storage for large frozen food items.
Product Specifications
The appearance and specifications listed in this manual may vary due to constant product improvements.
Electrical requirements: 115 V, 60 Hz
Min. / Max. water pressure: 20 - 120 psi (138 - 827 kPa)
Model LMWS27626*
Description Standard-depth, French door refrigerator, bottom freezer
Net weight 287 lb (130 kg)
Model LMWC23626*
Description Standard-depth, French door refrigerator, bottom freezer
Net weight 265 lb (120 kg)
10 INSTALLATION
INSTALLATION
Before Installing
Installation Overview
Please read the following installation instructions first after purchasing this product or transporting it to
another location.
a Unpacking the Refrigerator
b Choosing the Proper Location
c Disassembling/Assembling
d Connecting the Water Line
e Leveling and Door Alignment
WARNING
Connect to potable water supply only.
11INSTALLATION
ENGLISH
Unpacking the Refrigerator
WARNING
Use two or more people to move and install the
refrigerator. Failure to do so can result in back
injury or other injury.
The refrigerator is heavy. Protect the floor when
moving the refrigerator for cleaning or service.
Always pull the refrigerator straight out when
moving it. Do not wiggle or walk the refrigerator
when trying to move it, as floor damage could
occur.
Keep flammable materials and vapors, such as
gasoline, away from the refrigerator. Failure to
do so can result in fire, explosion, or death.
NOTE
Remove tape and any temporary labels from
your refrigerator before using. Do not remove
any warning labels, the model and serial number
label, or the Tech Sheet that is located under the
front of the refrigerator.
To remove any remaining tape or glue, rub the
area briskly with your thumb. Tape or glue
residue can also be easily removed by rubbing a
small amount of liquid dish soap over the
adhesive with your fingers. Wipe with warm
water and dry.
Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove
tape or glue. These products can damage the
surface of your refrigerator.
Reinstall or adjust shelves as needed.
Refrigerator shelves are installed in the shipping
position. Reinstall shelves according to your
individual storage needs.
Choosing the Proper
Location
Water
Must be located where a water supply can be
connected for the automatic icemaker.
NOTE
The water pressure must be 20 - 120 psi or 138 -
827 kPa or 1.4 - 8.4 kgf/cm
2
. If the refrigerator is
installed in an area with low water pressure
(below 20 psi or 138 kPa or 1.4 kgf/cm
2
), you can
install a booster pump to compensate for the
low pressure.
Electricity
Use an individual, grounded outlet:115 Volts, 60
Hz, AC, 15 Amps minimum.
WARNING
Do not overload house wiring and cause a fire
hazard by plugging in multiple appliances in the
same outlet with the refrigerator.
To reduce the risk of electric shock, do not install
the refrigerator in a wet or damp area.
Flooring
To avoid noise and vibration, the unit must be
installed and leveled on a solidly constructed floor.
If required, adjust the leveling legs to compensate
for the unevenness of the floor.
NOTE
Installing on carpeting, soft tile surfaces, a
platform or weakly supported structure is not
recommended.
Ambient Temperature
Install this appliance in an area where the
temperature is between 55 °F (13 °C) and 110 °F
(43 °C).
If the temperature around the appliance is too low
or high, cooling ability may be adversely affected.
12 INSTALLATION
Dimensions and Clearances
Check the dimensions of the appliance and the installation path to ensure there is sufficient room to
move the refrigerator through doors or narrow openings.
If an opening is too narrow to fit the refrigerator through, remove the refrigerator doors. See Removing/
Assembling the Doors and Drawers in this manual.
The installation location chosen for the refrigerator should allow space behind the unit for connections
and airflow and space in front to open the doors and drawers.
Too small of a distance from adjacent items may result in lowered freezing capability and increased
electricity consumption charges. Allow at least 24 inches (610 mm) in front of the refrigerator to open the
doors, and at least 2 inches (50.8 mm) between the back of the refrigerator and the wall.
- Dimension/Clearance LMWS27626* LMWC23626*
A Depth without Handle 32 3/8˝ (822 mm) 28 5/8˝ (728 mm)
B Width 35 3/4" (908 mm) 35 3/4" (908 mm)
C Height to Top of Case 68 3/8" (1737 mm) 68 3/8" (1737 mm)
D Height to Top of Hinge 69 3/4" (1772 mm) 69 3/4" (1772 mm)
E Back Clearance 2" (50 mm) 2" (50 mm)
F Depth without Door 28 1/2˝ (724 mm)
24 3/4˝ (630 mm)
G Depth with Handle 30 7/8˝ (886 mm) 31 1/4˝ (792 mm)
H Depth (Total with Freezer Drawer Open) 54 3/4˝ (1391 mm) 51˝ (1297 mm)
I Depth (Total with Door Open 90°) 47 1/8˝ (1197 mm) 43 3/8˝ (1103 mm)
B
A
C
D
F
I
H
E
G
13INSTALLATION
ENGLISH
Removing/Assembling the
Handles
When moving the refrigerator through a narrow
opening, removing the doors is preferred.
The appearance of the handles may vary from
what is shown.
WARNING
When assembling or disassembling the
refrigerator handles, grasp the handle firmly to
avoid dropping it.
Do not swing the handle into nearby people or
animals.
Make sure that the bracket hole of the handle
fits properly into the stopper bolt of the door.
Assemble the set screws to fix the handle into
place.
Make sure that there is not a gap between the
door and handle after assembling the handle.
Tools Needed
3/32 in. Allen wrench
1/8 in. Allen wrench
1/4 in. Allen wrench
Removing the Refrigerator Handles
1 Loosen the set screws a with a 3/32 in. Allen
wrench and remove the handle.
2 Loosen the mounting fasteners b that
connect to the refrigerator door and handle
using a ¼ in. Allen wrench, and remove the
mounting fasteners.
Assembling the Refrigerator
Handles
1 Assemble the mounting fasteners a at both
ends of the handle with a 1/4 in. Allen wrench.
2 Place the handle on the door by fitting the
handle footprints over the mounting
fasteners and tightening the set screws
b
with a 3/32 in. Allen wrench.
Removing the Freezer Drawer
Handle
1 Loosen the set screws a located on the lower
side of the handle with a 1/8 in. Allen wrench
and remove the handle.
2 Loosen the mounting fasteners b with a 1/4
in. Allen wrench, and remove the mounting
fasteners.
Assembling the Freezer Drawer
Handle
1 Assemble the mounting fasteners a at both
ends of the handle with a 1/4 in. Allen wrench.
2 Place the handle on the door by fitting the
handle footprints over the mounting
fasteners and tightening the set screws
b
with a 1/8 in. Allen wrench.
14 INSTALLATION
Removing/Assembling the
Doors and Drawer
If the entrance door is too narrow for the
refrigerator to pass through, remove the
refrigerator doors and move the refrigerator
sideways through the doorway.
WARNING
Use two or more people to remove and install
the refrigerator doors and freezer drawer.
Disconnect the electrical supply to the
refrigerator before installing.
Do not put hands, feet or other objects into the
air vents or bottom of the refrigerator.
Be careful when handling the hinge and stopper.
WARNING
Remove food and bins before detaching the
doors and drawer.
Do not hold the handle when removing or
replacing the doors and drawer as the handle
may come off.
Tools Needed
3/32 in. Allen wrench
1/8 in. Allen wrench
1/4 in. Allen wrench
Removing the Left Refrigerator
Door
1 Remove the screw a from the hinge cover at
the top of the refrigerator. Lift the hook (not
visible), located at the bottom of the front side
of the cover
b with a flat-head screwdriver.
Remove the cover
2 Disconnect all wire harnesses c. Unscrew the
ground wire
d .
3 Rotate the hinge lever e counterclockwise.
Lift the top hinge
f free of the hinge lever
latch
g .
CAUTION
When lifting the hinge free of the latch, be
careful that the door does not fall forward.
4 Lift the door from the middle hinge pin and
remove the door.
CAUTION
Place the door, inside facing up, on a
nonscratching surface.
Removing the Right Refrigerator
Door
1 Remove the top hinge cover screw a. Lift the
hook (not visible), located at the bottom of the
front side of the cover
b, with a flat-head
screwdriver.
15INSTALLATION
ENGLISH
2 Detach all the wire harnesses c.
3 Rotate the hinge lever d clockwise. Lift the
top hinge
e free of the hinge lever latch f.
CAUTION
When lifting the hinge free of the latch, be
careful that the door does not fall forward.
4 Lift the door from the middle hinge pin and
remove the door.
CAUTION
Place the door, inside facing up, on a
nonscratching surface.
Assembling the Right Refrigerator
Door
CAUTION
Install the right-side door first.
1 Make sure that the plastic sleeve is inserted in
the bottom of the door. Lower the door onto
the middle hinge pin as shown in the figure.
2 Fit the hinge a over the hinge lever latch b
and slot it into place. Rotate the lever
c
counterclockwise to secure the hinge.
3 Connect the wire harnesses d.
4 Place the cover e in its place. Insert and
tighten the cover screw
f .
16 INSTALLATION
Assembling the Left Refrigerator
Door
CAUTION
Install the left refrigerator door after the right
door is installed.
1 Make sure that the plastic sleeve is inserted in
the bottom of the door. Install the refrigerator
door onto the middle hinge.
2 Fit the hinge a over the hinge lever latch b
and slot it into place. Rotate the lever
c
clockwise and fasten the hinge.
3 Connect all the wire harnesses d and the
ground screw
e.
4 Place the hinge cover f in place. Insert and
tighten the cover screw
g.
Removing the Freezer Drawer
Removing the lower freezer drawer in the same
way.
WARNING
Use two or more people to remove and install
the refrigerator doors and freezer drawer.
Be careful of sharp hinges on both sides of the
drawer.
When you lay the drawer down, be careful not to
damage the floor.
Do not sit or stand on the freezer drawer.
To prevent accidents, keep children and pets
away from the drawer. Do not leave the drawer
open. If the Durabase
®
storage bin is removed
from the freezer drawer, there is sufficient space
for a small child or pet to crawl inside.
1 Pull the drawer open to full extension.
Removing the basket and ice bin from the
rails.
2 Remove the screws from the rails at both
ends.
3 Grip both sides of the drawer and pull it up to
remove it from the rails.
17INSTALLATION
ENGLISH
CAUTION
Do not hold the handle when removing or
replacing the drawer. The handle may come off,
causing personal injury.
4 Hold both rails and push them in
simultaneously.
Assembling the Freezer Drawer
Assembling the lower freezer drawer in the same
way.
1 Pull out both rails simultaneously, until they
are fully extended.
2 Grasp the drawer on each side and hook the
drawer supports into the rail tabs located on
both sides.
CAUTION
Do not hold the handle when removing or
replacing the drawer. The handle may come off,
causing personal injury.
3 Lower the door into its final position and
insert the screws in the rails on both sides.
4 Insert the basket into the frame, and push the
drawer back until it clicks into place.
18 INSTALLATION
Connecting the Water Line
Before Beginning
This water line installation is not covered by the
refrigerator warranty. Follow these instructions
carefully to minimize the risk of expensive water
damage.
If necessary, call a qualified plumber to correct
water hammer before installing the water supply
line to the refrigerator. Water banging in the
pipes, or water hammer in residential plumbing
can cause damage to refrigerator parts and lead to
water leakage or flooding.
Turn the icemaker OFF if the refrigerator will be
used before the water line is connected.
Do not install the icemaker tubing in areas
where the ambient temperatures fall below
freezing.
WARNING
Connect to potable water supply only.
CAUTION
To prevent burns and product damage, only
connect the refrigerator water line to a cold
water supply.
Wear eye protection during installation to
prevent injury.
Water Pressure
You will need a cold water supply.
If the water pressure from the reverse osmosis
system is less than 20 psi or 138 kPa or 1.4 kgf/
cm
2
(takes more than 4 seconds to fill a cup of 7 oz
or 198 cc capacity):
Check to see if the sediment filter in the reverse
osmosis system is blocked. Replace the filter if
necessary.
Allow the storage tank on the reverse osmosis
system to refill after heavy usage.
If the water pressure remains low, call a
licensed, qualified plumber.
All installations must be in accordance with local
plumbing code requirements.
Supplies Needed
Copper or PEX Tubing, ¼ in. outer diameter, to
connect the refrigerator to the water supply. Be
sure both ends of the tubing are cut square. To
determine how much tubing you need, measure
the distance from the water valve on the back of
the refrigerator to the water supply pipe. Then,
add 8 feet (2.4 m). Be sure there is sufficient
extra tubing (about 8 feet [2.4 m] coiled into 3
turns of about 10 in. [25 cm] diameter) to allow
the refrigerator to move out from the wall after
installation.
Power drill.
½ in. or adjustable wrench.
Flat-blade and Phillips-head screwdrivers.
Two ¼ in. outer diameter compression nuts
and 2 ferrules (sleeves) to connect the copper
tubing to the shutoff valve and the refrigerator
water valve.
If your existing copper water line has a flared
fitting at the end, purchase an adapter (available
at plumbing supply stores) to connect the water
line to the refrigerator OR cut off the flared
fitting with a tube cutter and then use a
compression fitting.
Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with
a minimum inside diameter of 5/32 in. at the
point of connection to the COLD WATER LINE.
Saddle-type shutoff valves are included in many
water supply kits. Before purchasing, make sure
a saddle-type valve complies with your local
plumbing codes.
Water Pressure
models with water
filter
20 - 120 psi (138 - 827 kPa)
where reverse
osmosis water
filtration system is
connected to a cold
water supply
40 - 60 psi minimum to
reverse osmosis system
(2.8 kgf/cm
2
- 4.2 kgf/ cm
2
,
or less than 2 - 3 seconds to
fill a cup of 7 oz capacity)
19INSTALLATION
ENGLISH
NOTE
A self-piercing saddle type water valve should
not be used.
Water Line Installation Instructions
Install the shutoff valve on the nearest frequently
used drinking water line.
WARNING
When using any electrical device (such as a
power drill) during installation, be sure the
device is battery-powered, double-insulated or
grounded in a manner that will prevent the
hazard of electric shock.
1 Shut off the main water supply.
Turn on the nearest faucet to relieve the
pressure on the line.
2 Choose the valve location.
Choose a location for the valve that is easily
accessible. It is best to connect into the side
of a vertical water pipe. When it is necessary
to connect into a horizontal water pipe,
make the connection to the top or side,
rather than at the bottom, to avoid drawing
off any sediment from the water pipe.
3 Drill the hole for the valve.
Drill a ¼ in. hole in the water pipe using a
sharp bit. Remove any burrs resulting from
drilling the hole in the pipe. Be careful not
to allow water to drain into the drill. Failure
to drill a ¼ in. hole may result in reduced ice
production or smaller cubes.
NOTE
The hookup line cannot be white, plastic tubing.
Licensed plumbers must use only copper tubing
(NDA tubing #49595 or #49599) or Cross Link
Polyethylene (PEX) tubing.
4 Fasten the shutoff valve.
Fasten the shutoff valve to the cold water
pipe with the pipe clamp.
NOTE
Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle
valves are illegal and use is not permitted in
Massachusetts. Consult with your licensed
plumber.
a Pipe Clamp
b Saddle-Type Shutoff Valve
c Vertical Cold Water Pipe
5 Tighten the pipe clamp.
Tighten the clamp screws until the sealing
washer begins to swell.
NOTE
Do not over tighten clamp or you may crush the
tubing.
20 INSTALLATION
a Pipe Clamp
b Inlet End
c Clamp Screw
d Washer
6 Route the tubing.
Route the tubing between the cold water
line and the refrigerator. Route the tubing
through a hole drilled in the wall or floor
(behind the refrigerator or adjacent base
cabinet) as close to the wall as possible.
NOTE
Be sure there is sufficient extra tubing (about 8
ft. coiled into three turns of about 10 in.
diameter) to allow the refrigerator to move out
from the wall after installation.
7 Connect the tubing to the valve.
Place the compression nut and ferrule
(sleeve) for copper tubing onto the end of
the tubing and connect it to the shutoff
valve. Make sure the tubing is fully inserted
into the valve. Tighten the compression nut
securely.
a Saddle-Type Shutoff Valve
b Compression Nut
c Packing Nut
d Outlet Valve
e Ferrule (sleeve)
8 Flush out the tubing.
Turn the main water supply on and flush
out the tubing until the water is clear. Shut
the water off at the water valve after about
one quart of water has been flushed
through the tubing.
9 Connect the tubing to the refrigerator.
NOTE
Before making the connection to the
refrigerator, be sure that the refrigerator power
cord is not plugged into the wall outlet.
Remove the plastic flexible cap from the water
valve.
Place the compression nut and ferrule (sleeve)
onto the end of the tubing as shown.
Insert the end of the copper tubing into the
connection as far as possible. While holding the
tubing, tighten the fitting.
a Tubing Clamp
b ¼ in. Tubing
c ¼ in. Compression Nut
d Ferrule (sleeve)
e Refrigerator Connection
1 / 1

Frigidaire LMWC23626S Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire