Zephyr ZSA-E30CB Le manuel du propriétaire

Use, Care, and Installation Guide

Model number:

Serial Number:

www.zephyronline.com

Savona Wall

ZSA-E30CB

ZSA-E30CS

ZSA-E30CW

ZSA-M90CB

ZSA-M90CS

ZSA-M90CW

www.goedekers.com

www.zephyronline.com

www.goedekers.com

1

SAFETY NOTICE ................................................................. 2-3

LIST OF MATERIALS ....................................................... 4

INSTALLATION

Ducting Calculation Sheet

....................................... 5

Mounting Height & Clearance

................................ 6

Ducting Options

........................................................... 7

Hood Speciﬁ cations

................................................... 8

Mounting the Hood

..................................................... 9

Ductless Recirculating

.............................................. 10

FEATURES & CONTROLS

ICON Touch Controls

................................................ 11-12

MAINTENANCE

Hood and Filter Cleaning

......................................... 13

Light Bulbs

..................................................................... 14

TROUBLESHOOTING

................................................................ 15

WIRING DIAGRAMS

................................................................... 16

FAN CURVE DIAGRAMS

......................................................... 17-18

LIST OF PARTS AND ACCESSORIES

.............................. 19

Table of Contents

www.goedekers.com

Important Safety Notice

READ AND SAVE THESE INSTRUCTIONS

2

www.zephyronline.com

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.

WARNING

TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.

b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service

panel.

CAUTION

For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning

agents or detergents. Suitable for use in household cooking area.

WARNING

TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:

a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly

on low or medium settings.

b. Always turn hood ON when cooking at high heat or when ﬂ aming food

c. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or ﬁ lter.

d. Use proper pan size. Always use cookware appropriate for the size of the surface element.

e. Keep fan, ﬁ lters and grease laden surfaces clean.

f. Use high setting on hood only when necessary.

g. Don’t leave hood unattended when cooking.

h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:

a. SMOTHER FLAMES with a close-ﬁ tting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.

If the ﬂ ames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

b. NEVER PICK UP A FLAMING PAN – You may be burned.

c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.

d. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. The ﬁ re is small and contained in the area where it started.

3. The ﬁ re department is being called.

4. You can ﬁ ght the ﬁ re with your back to an exit

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a. Installation work and electrical wiring must be done by qualiﬁ ed person(s) in accordance with all applicable codes and standards.

Including ﬁ re-rated construction.

b. Sufﬁ cient air is needed for power combustion and exhausting of gases through the ﬂ ue (chimney) of fuel burning equipment to prevent

back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National

Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and

the local code authorities.

c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

d. Ducted fans must always vent to the outdoors.

e. NEVER place a switch where it can be reached from a tub or shower.

f. Make sure the power is off before installing, wiring or maintenancing.

www.goedekers.com

Important Safety Notice

3

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

CAUTION

To reduce risk of ﬁ re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings,

attics, crawl spaces or garages.

Not for use over an outdoor grill.

OPERATION

Always leave safety grilles and ﬁ lters in place. Without these components, operating blowers could catch onto hair, ﬁ ngers

and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,

maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to

negligence and the warranty of the unit automatically expires due to improper maintenance.

*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

ELECTRICAL REQUIREMENTS

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility:

- To contact a qualiﬁ ed electrical installer.

- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and

all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualiﬁ ed electrician determine that the

ground path is adequate.

Do not ground to a gas pipe.

Check with a qualiﬁ ed electrician if you are not sure the range hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit

protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to

Electrical Diagram on product.

A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase

and install appropriate connector if necessary.

www.goedekers.com

4

www.zephyronline.com

(3) Wire Nuts

(2) M4 x 1-1/2”

(3) M4 x 1”

(2) M4 x 8

PARTS NOT SUPPLIED

- Ducting, conduit and all installation tools

- Cable connector (if required by local codes)

- Extension duct cover accessory - Z1C-01SA, Z1C-01SAB, Z1C-01SAW

- Recirculating kit accessory - ZRC-00SV

HARDWARE PACKAGE CONTENTS

MODELS:

(1) Suction Cup

1 - Hood body with internal blower

2 - Aluminum mesh filters

1 - Duct cover assembly, top and bottom

1 - Duct cover wall bracket

2 - 50W GU-10 halogen light bulbs

1 - 6” round damper, pre-installed

1 - Hardware package

PARTS SUPPLIED

ZSA

www.goedekers.com

5

Duct pieces

To t a l

Equivalent number

length x used =

3- 1/ 4” x 10”

Rect.,

straight

1 Ft. x ( ) =

Ft.

8” Round,

straight

1 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

elbow

15 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 45

0

elbow

9 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

flat elbow

24 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect.

wall cap

with damper

30 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

5 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

90

0

elbow

20 Ft. x ( ) =

Ft.

6” Round,

90

0

elbow

15 Ft. x ( ) =

Ft.

6” Round,

45

0

elbow

9 Ft. x ( ) =

Ft.

7” Round,

straight

1 Ft. x ( ) =

Ft.

Subtotal column 1 =

Duct pieces

To t a l

Equivalent number

length x used =

6”- 8” Round

wall cap

with damper

30 Ft. x ( ) =

Ft.

Round

wall cap

with damper

30 Ft. x ( ) =

Ft.

7” or 8”

Round,

90

0

elbow

15 Ft. x ( ) =

Ft.

7” or 8”

Round,

45

0

elbow

9 Ft. x ( ) =

Ft.

6”- 8” Round,

roof cap

30 Ft. x ( ) =

Ft.

7” or 8”

Round,

roof cap

30 Ft. x ( ) =

Ft.

Subtotal column 2 =

Subtotal column 1 =

Total ductwork =

Maximum Duct Length: For satisfactory air movement,

the total duct length of a 3 1/ 4” x 10” rectangular 6” or 7”

diameter round duct should not exceed 100 equivalent feet.

6” round to

3- 1/ 4” x 10”

rect.

transition

1 Ft. x ( ) =

Ft.

6” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

16 Ft. x ( ) =

Ft.

7” round to

3 1/ 4” x 10”

rect.

transition

8 Ft. x ( ) =

Ft.

7” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

23 Ft. x ( ) =

Ft.

Installation – Ducting Calculation Sheet

www.goedekers.com

Installation – Mounting Height & Clearance

6

www.zephyronline.com

DUCTING

A minimum of 6” round duct must be used to

maintain maximum air ﬂ ow efﬁ ciency.

Always use rigid type metal ducts only. Flexible

ducts could restrict air ﬂ ow by up to 50%.

Use calculation worksheet to compute total duct

work (Page 5).

ALWAYS, when possible, reduce the number of

transitions and turns. If a long duct run is required,

increase duct size from 6” to 7” or 8”.

If turns or transitions are required: Install as far

away from duct opening and as far apart between

the two transitions as possible.

Minimum mount height between range top to hood

bottom should be no less than 26”.

Maximum mount height should be no higher than

34”.

It is important to install the hood at the proper

mounting height. Hoods mounted too low could

result in heat damage and ﬁ re hazard; while hoods

mounted too high will be hard to reach and will

loose performance and efﬁ ciency.

If available, also refer to range manufacturer’s

height clearance requirements and recommended

hood mounting height above range. Always check

your local codes for any differences.

Duct cover extension kit available for ceiling

heights up to 12 feet. Turn to page 19 for part

number and ordering information.

DAMAGE-SHIPMENT / INSTALLATION:

•

Please fully inspect unit for damage before

installation.

•

If the unit is damaged in shipment, return the

unit to the store in which it was bought for

repair or replacement.

• If the unit is damaged by the customer, repair

or replacement is the responsibility of the

customer.

• If the unit is damaged by the installer (if other

than the customer), repair of replacement must

be made by arrangement between customer

and installer.

26” min.

34” max.

min. A

min. B

max. C

min. D

min. E

max. F

Standard Extension

Hood Heights Duct Cover Duct Cover

minimum ducted (A) 28” 45-

1/2“

minimum recirculating (B) 32” 50“

maximum (C) 45” 80”

Ceiling Heights

minimum ducted (D) 90” (7’ 6”) 107-

1/2“ (9‘)

minimum recirculating (E) 94” (7’ 10”) 112“ (9‘ 4”)

maximum (F) 115” (9’ 7“) 150” (12’ 6”)

36”

www.goedekers.com

7

WARNING FIRE HAZARD

NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.

All exhaust must be ducted to the outside, unless using the recirculating option.

Use single wall rigid metal ductwork only.

Fasten all connections with sheet metal screws and tape all joints w/ certiﬁ ed Silver Tape or Duct Tape.

Some Ducting Options

Installation – Ducting Options

side wall cap

w/ gravity damper

Soffit or crawl space

Roof Pitch w/

Flashing & Cap

ductless

recirculating

side wall cap

w/ gravity damper

www.goedekers.com

8

www.zephyronline.com

Installation – Hood Speciﬁ cation

4"

6

"

CL

1”

9”

1”

29 15/16”, 35 7/16”

7

1

/2”

19

1/2”

11”

STANDARD

min. ducted - 28”

min. recirc. - 32”

max. - 45”

Z1C-01SA, Z1C-01SAB

Z1C-01SAW

EXTENSIONS

min. ducted - 45

1/2”

min. recirc. - 50”

max. - 80”

1/2”

www.goedekers.com

9

1. Measure from range top to hood bottom and mark line A.

(26” minimum from range top) .

2. Plum and mark center line.

3. Mark hood height line B. (9-1/2” from line A)

4. Mark mounting spread from C/L. (9-7/8” on line B)

5. Fasten (2) M4 x 1-1/2” screws into studs on line B but

do not tighten all the way. Note: Wood blocking may

need to be added behind the drywall if no studs are

present. Wall anchors may also be used but check

local codes for compliance. Failure to use suitable

wall anchors and screws to hold the weight of the

hood could result in personal injury or damage to

the cooking surface or counter.

6. Remove the (2) aluminum mesh ﬁ lters.

7. Hang hood onto the mounting screws and hand tighten

each screw. (Fig A)

8. Center and attach duct cover mounting bracket to wall

just below the ceiling or sofﬁ t using (2) M4 x 1” screws.

9. Install electrical and duct work. Seal duct work with

aluminum duct tape.

10. Power up hood and check for leaks around duct tape.

11. Place telescopic duct covers onto hood and extend

inner (top) duct cover upwards and secure to duct cover

bracket using (2) M4 x 8 screws. Reinstall mesh ﬁ lters.

* If using hood in recirculating mode you must secure the

air diverter plate onto wall before installing duct work and

duct covers. You will also need to install charcoal ﬁ lters

and brackets. Turn to page 10 for more details.

9-7/8”

9-

1/2

”

26” min.

6-

1/2

”

CAUTION: At least two installers are required

due to the weight and size of the hood.

!

WARNING: Electrical wiring must be done by a qualified person(s) in

accordance with all applicable codes and standards. This range hood must be

properly grounded. Turn off electrical power at service entrance before wiring.

!

Cable Lock

A cable locking connector (not supplied) might

be required by local codes. Check with local

requirements and codes, purchase and install

appropriate connector if necessary.

Installation – Mounting the Hood

FIG. A

www.goedekers.com

10

www.zephyronline.com

Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed.

When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust

from cooking are drawn and ﬁ ltered by a set of optional charcoal ﬁ lters. The air is then puriﬁ ed and re-

circulated back within the home.

We recommend to ALWAYS exhaust air outside of the home by employing existing or installing new duct

work, if possible. The hood is most effective and efﬁ cient as an exhaust hood. Only when the exhaust option

is not possible should you recourse to converting the hood into a recirculating hood.

When converted to be a recirculating hood, a set of charcoal ﬁ lters are required on top of its standard mesh

ﬁ lter set. Order according to its part number below. The standard mesh ﬁ lters are intended to capture residue

from cooking and the optional charcoal ﬁ lters help to purify fumes exhausted from cooking for re-circulation.

RECIRCULATING KIT (REQUIRED IF NO DUCTING IS USED)

Kit includes charcoal ﬁ lters and air diverter plate.

Hood Models Part No. Filters & Brackets in pkg.

ZSA ZRC-00SV 2

1. Purchase recirculating kit per the part number above

2. Secure air diverter plate to wall below duct cover bracket. Run 6”

ducting from top of hood and secure to air diverter plate. (FIG. B)

3. Remove aluminum mesh ﬁ lters from hood. Secure charcoal ﬁ lter

brackets to the hood body behind each mesh ﬁ lters using the screws

included in the recirculating kit. Clip charcoal ﬁ lters onto each charcoal

ﬁ lter bracket. (FIG. B)

4. Re-Install mesh ﬁ lters. For more details refer to manual included

with recirculating kit.

5. Charcoal ﬁ lters must be replaced after every 120 hours of use (or

approximately every 3 to 4 months based on an average of 1 - 2 hrs. of

daily cooking time).

Charcoal Filter Replacements

Hood Model Part No. Qty to Order

ZSA Z0F-C002 2

DO NOT WASH CHARCOAL FILTERS. Charcoal ﬁ lters may need

to be changed more often depending on cooking habits.

Installation – Ductless Recirculating

FIG. B

www.goedekers.com

11

Lights On/Dim/Off

Display (speed level, delay off, filter clean/change)

Adjust 5 Speed Levels

Power / Delay Off

1 POWER / DELAY OFF BUTTON

Power Button Function

- Button will turn power on and off for entire hood (fan and lights).

- Hood will remember the last speed and light level it was turned off at.

(Example: Press Button to turn off hood when on fan speed 4 and high lights. Press Button

again and the hood will turn back on at speed 4 and high lights level.)

Delay Off Button Function

- With the fan on press and hold the Button for two seconds. The fan will change to speed 1 and the

5 minute delay off timer will start.

+ LEDs will illuminate and slowly blink in accordance with the time

remaining until the fan and lights automatically turn off.

- Pressing Button while Delay Off Function is enabled will turn the hood off and cancel the Delay Off

Function.

ACT Verification

- Airflow Control Technology (ACT) allows the installer to set the maximum fan CFM to align with local

codes and regulations.

- To verify the maximum fan CFM:

- With hood off, hold the Button for two seconds. If all five fan speed indicators illuminate =

default maximum CFM. If four fan speed indicators illuminate = 390 maximum CFM. If 3 fan

speed indicators illuminate = 290 maximum CFM.

2 SPEED SELECTION BUTTON

Fan Speed Decrease Button

- Press this button to decrease fan speed. 5, 4, 3, 2, 1.

- If fan is On Speed 1 and this button is pressed, fan will power Off.

Fan Speed Increase Button

- Press this button to increase fan speed. Fan On, 1, 2, 3, 4, 5.

- If hood is Off and this button is pressed, fan will turn On Speed 1.

Act Enabled Speed Selections

- When ACT is enabled, the number of fan speeds will be reduced as follows:

- 390 CFM = Maximum 4 speeds

- 290 CFM = Maximum 3 speeds

Features & Controls - ICON Touch Controls

www.goedekers.com

12

www.zephyronline.com

Features & Controls - ICON Touch Controls

3 LIGHTS BUTTON

- Lights are two levels, High and Low.

- From off, press one time for High. Press again for Low. Press again to power lights off.

4 DISPLAY INDICATORS

Mesh Filter Clean Reminder (always enabled)

- After 30 hours of fan usage, the button indicator will begin to slowly blink indicating it is time to

clean the mesh filters.

- To reset: With hood off: hold the button for three seconds. All LED indicators will blink two times

confirming the 30 hour timer has been reset.

Charcoal Filter Replace Indicator (disabled by default, must be enabled if recirculating hood)

- To enable Charcoal Filter Replacement Reminder:

- With hood off, hold button and button simultaneously for two seconds. All LED indicators

will illuminate for three seconds confirming the Charcoal Filter Replace Reminder is enabled.

- To disable Charcoal Filter Replacement Reminder:

- With hood off, hold button and button simultaneously for two seconds. All LED indicators

will blink two times confirming the Charcoal Filter Replace Reminder is disabled.

- After 120 hours of fan usage the button will slowly blink indicating the charcoal filters need

replacment.

- To reset: With hood off, hold the button for two seconds. All LED indicators will blink two times

confirming the 120 hour timer has been reset.

www.goedekers.com

13

SURFACE MAINTENANCE:

Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent

or steel wool/scouring pads which will scratch and damage surface.

For heavier soil use liquid degreaser.

After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners, to polish and

buff out the stainless luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.

Do not use any product containing chlorine bleach. Do not use “orange” cleaners.

Aluminum Mesh Filters

The aluminum mesh ﬁ lters installed by the factory are intended to ﬁ lter out residue and grease from

cooking. They need not be replaced on a regular basis but are required to be kept clean.

Remove and clean by hand or in dishwasher on low heat. Spray degreasing detergent and leave to soak if

heavily soiled.

Dry ﬁ lters and re-install before using hood.

Removing Aluminum Mesh Filters

1. Pull down on ﬁ lter latch to disengage the springs

2. Pull down on ﬁ lter hande to remove ﬁ lter

Maintenance – Hood and Filter Cleaning

www.goedekers.com

14

www.zephyronline.com

REPLACING LIGHT BULBS

CAUTION: Light bulb becomes extremely hot when turned on.

DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns.

Make sure all power is turned off and bulbs are not hot.

Remove by turning bulb counter clockwise. Note: Bulb does not unscrew; it turns 60 degrees,

stops and falls out.

If bulbs are difﬁ cult to turn due to prolonged use, ﬁ rmly attach the included glass suction cup or use a rubber/

latex glove grip and turn the bulb counter clockwise.

Replacement bulbs are available at specialty lighting stores. Purchase type GU-10 50W halogen.

For part numbers please turn to page 19 of the manual.

Maintenance – Light Bulbs

www.goedekers.com

15

Troubleshooting

TROUBLESHOOTING PROCEDURES FOR ZSA

Issue Cause What to do

After installation,

the unit doesn’t

work.

1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s

power is ON.

2. The power line and the cable locking connector

is not connecting properly.

2. Check the power connection with the unit is

connected properly.

3. The switch board and control board wirings are

disconnected.

3. Make sure the wirings between the switch

board and control board are connected

properly.

4. The switch board or control board is defective. 4. Change the switch board or control board.

Light works, but

blower is not

turning.

1. The blower cable is disconnected. 1. Check all wiring from the blower to be sure all

cables are connected properly.

2. The blower is defective, possibly seized. 2. Change the blower.

3. The thermally protected system detects if the

blower is too hot to operate and shuts the blower

down.

3. The blower will function properly after the

thermally protected system cool down.

4. Damaged capacitor. 4. Change the capacitor.

5. The switch board or control board is defective. 5. Change the switch board or control board.

The unit is

vibrating.

1. The blower is not secured in place. 1. Tighten the blower in place.

2. Damaged blower wheel. 2. Replace the blower.

3. The hood is not secured in place. 3. Check the installation of the hood.

The blower is

working, but the

lights are not.

1. The light socket connector is loose or

disconnected.

1. Check the light socket connector to be sure it

is pluged in properly.

2. Defective halogen bulb. 2. Change the halogen bulb.

3. The light bulb is loose. 3. Tighten the light bulb.

The speed levels

sound the same.

1. Using the wong size of ducting. 1. Change the duct pipe size to at least 6” round

or higher.

The unit turns on

by itself.

1. A spot light or kitchen lamp is shining directly

onto the switch controls.

1. The switch controls are light sensative. A

direct light source onto the switch controls

may disrupt switch functions.

The unit is

whistling.

1. The duct pipe connections are not sealed or

connected properly.

1. Check the duct pipe connections to be sure all

connections are sealed properly.

The hood is

not venting out

properly.

1. The hood might be hanging to high from the

cook top.

1. Adjust the distance between the cook top and

the bottom of the hood within 26” and 34”

range.

2. The wind from the opened windows or opened

doors in the surrounding area are affecting the

ventilation of the hood.

2. Close all the windows and doors to eliminate

the outside wind ﬂ ow.

3. Blockage in the duct opening or ductwork. 3. Remove all the blocking from the duct work or

duct opening.

4. The direction of duct opening is against the wind. 4. Adjust the duct opening direction.

5. Using the wrong size of ducting. 5. Change the ducting to at least 6” or higher.

Mesh Filter is

vibrating.

1. Mesh ﬁ lter is loose. 1. Change the mesh ﬁ lter.

2. Filter spring clip is loose or broken. 2. Uninstall and reinstall ﬁ lter, push up on ﬁ lter

latch. Replace mesh ﬁ lter if needed.

www.goedekers.com

16

www.zephyronline.com

Wiring Diagrams

VOLTS

HZ

MAX AMPS

120 60 3.5

USE ONLY TYPE MR16, GU10, 50 W. MAX. HALOGEN LIGHT BULBS.

ZSA-E30CS, ZSA-M90CS

ZSA-E30CB, ZSA-M90CB

ZSA-E30CW, ZSA-M90CW

Power consumption shown for default 685 CFM blower conﬁ guration

ACT 390 CFM - Fan Max. 300W @ 2.6A

ACT 290 CFM - Fan Max. 289W @ 2.4A

www.goedekers.com

17

Fan Curve Diagrams

Airﬂ ow Control Technology (ACT)

Some local codes limit the maximum amount of CFM a range hood can move. ACT allows you to

control the maximum blower CFM of hoods with of select Zephyr Ventilation range hoods without the

need for expensive make up air kits. ACT enables the installer to easily set the maximum blower speed

to one of two most commonly speciﬁ ed CFM levels; 390 or 290 CFM. The usage of ACT may not be

necessary for your installation. Please check your local codes for CFM restrictions.

By default the maximum blower CFM is set to 685.

To verify if your installer enabled ACT; With hood off, press and hold the power button for three seconds.

If 5 LEDs illuminate = default max. CFM, if 4 LEDs illuminate = max. 390 CFM, and if 3 LEDs illuminate

= max. 290 CFM. When ACT is enabled, the number of blower speeds will be reduced. 390 CFM = max.

3 speeds and 290 CFM = max. 2 speeds. There should also be a foil label located inside the hood body

near the wiring diagram that indicates the blower CFM.

www.goedekers.com

www.zephyronline.com

Fan Curve Diagrams

18

www.goedekers.com

La page charge ...

Zephyr ZSA-E30CB Le manuel du propriétaire

Zephyr ZSA-E30CB Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents