Skil CS4562B-10 Manuel utilisateur

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

Owner’s Manual

Guide d’utilisation

Manual del propietario

For Customer Service

Pour le service à la clientèle

Servicio al cliente

20V 12'' Brushless Chain Saw

Scie à chaîne sans balai de 20 V, 30 cm / 12 po

Motosierra sin escobillas de 12 pulgadas de 20 V

1-877-SKIL-999

OR

www.skil.com

Model/ Modelo/ Modèle: CS4562B-00

2

TABLE OF CONTENTS

General Power Tool Safety Warnings .............................3-5

Chain Saw Safety Warnings .....................................5-7

Additional Warnings ...........................................8-9

Symbols ...................................................10-13

Get to Know Your Chain Saw ..................................14-15

Speciﬁcations .................................................16

Recommended Bar and Chain for This Chain Saw ...................16

Operating Instructions .......................................17-25

Maintenance ...............................................26-33

Troubleshooting .............................................34-35

Limited Warranty of SKIL Consumer Tool ...........................36

WARNING

•

Some dust created by power sanding, sawing, grinding, drilling and other

construction activities contains chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. Some examples of these chemicals are:

–

Lead from lead-based paints.

–

Crystalline silica from bricks, cement, and other masonry products.

–

Arsenic and chromium from chemically-treated lumber.

•

Your risk from these exposures varies, depending upon how often you do this type of work.

To reduce your exposure to these chemicals:

–

Work in a well-ventilated area.

–

Work with approved safety equipment, such as dust masks that are specially designed to

lter out microscopic particles.

3

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and specifications

provided with this power tool.

Failure to follow all instructions listed

below may result in electric shock, re and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit

. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which may ignite the dust or

fumes.

Keep children and bystanders away while operating a power tool.

Distractions can cause

you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools.

Unmodied plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges

and refrigerators.

There is an increased risk of electric shock if your body is earthed or

grounded.

Do not expose power tools to rain or wet conditions.

Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply.

Use of a GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol

or medication.

A moment of inattention while operating power tools may result in serious

personal injury.

Use personal protective equipment. Always wear eye protection.

Protective equipment

such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before connecting

to power source and/or battery pack, picking up or carrying the tool.

Carrying power

tools with your nger on the switch or energising power tools that have the switch on invites

accidents.

Remove any adjusting key or wrench before turning the power tool on.

A wrench or a key

left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times.

This enables better

control of the power tool in unexpected situations.

4

Dress properly. Do not wear loose clothing or jewellery. Keep your hair, and clothing

away from moving parts.

Loose clothes, jewellery or long hair can be caught in moving parts.

If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used.

Use of dust collection can reduce dust-

related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent

and ignore tool safety principles.

A careless action can cause severe injury within a fraction

of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application.

The correct

power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off.

Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or remove the battery pack, if

detachable, from the power tool before making any adjustments, changing accessories,

or storing power tools.

Such preventive safety measures reduce the risk of starting the

power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool.

Power tools are

dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use.

Many accidents are

caused by poorly maintained power tools.

Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed.

Use of the

power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and free from oil and grease.

Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in

unexpected situations.

Battery tool use and care

Recharge only with the charger specified by the manufacturer.

A charger that is suitable

for one type of battery pack may create a risk of re when used with another battery pack.

Use power tools only with specifically designated battery packs.

Use of any other battery

packs may create a risk of injury and re.

When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection from

one terminal to another.

Shorting the battery terminals together may cause burns or a re.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek

medical help.

Liquid ejected from the battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or modified.

Damaged or modied

batteries may exhibit unpredictable behaviour resulting in re, explosion or risk of injury.

Do not expose a battery pack or tool to fire or excessive temperature.

Exposure to re or

temperature above 265 °F may cause explosion.

5

Follow all charging instructions and do not charge the battery pack or tool outside the

temperature range specified in the instructions.

Charging improperly or at temperatures

outside the specied range may damage the battery and increase the risk of re.

Service

Have your power tool serviced by a qualified repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

Never service damaged battery packs.

Service of battery packs should only be performed

by the manufacturer or authorized service providers

CHAIN SAW SAFETY WARNINGS

Keep all parts of the body away from the saw chain when the chain saw is operating.

Before you start the chain saw, make sure that the saw chain is not contacting anything.

A moment of inattention while operating chain saws may cause entanglement of your clothing

or body with the chain.

Always hold the chain saw with your right hand on the rear handle and your left hand on

the front handle.

Holding the chain saw with a reversed hand conguration increases the risk

of personal injury and should never be done.

Hold the chain saw by insulated gripping surfaces only, because the saw chain may

contact hidden wiring or its own cord.

Saw chains contacting a “live” wire may make

exposed metal parts of the chain saw “live” and could give the operator an electric shock.

Wear eye protection. Further protective equipment for hearing, head, hands, legs and

feet is recommended.

Adequate protective equipment will reduce personal injury from ying

debris or accidental contact with the saw chain.

Do not operate a chain saw in a tree, on a ladder, from a rooftop, or any unstable

support.

Operation of a chain saw in this manner could result in serious personal injury.

Always keep proper footing and operate the chain saw only when standing on fixed,

secure and level surface.

Slippery or unstable surfaces may cause a loss of balance or

control of the chain saw.

When cutting a limb that is under tension, be alert for spring back.

When the tension in

the wood bres is released, the spring loaded limb may strike the operator and/or throw the

chain saw out of control.

Use extreme caution when cutting brush and saplings.

The slender material may catch the

saw chain and be whipped toward you or pull you off balance.

Carry the chain saw by the front handle with the chain saw switched off and away from

your body. When transporting or storing the chain saw, always fit the guide bar cover.

Proper handling of the chain saw will reduce the likelihood of accidental contact with the

moving saw chain.

Follow instructions for lubricating, chain tensioning and changing the bar and chain.

Improperly tensioned or lubricated chain may either break or increase the chance for kickback.

Cut wood only. Do not use chain saw for purposes not intended. For example: do not

use chain saw for cutting metal, plastic, masonry or non-wood building materials.

Use of

the chain saw for operations different than intended could result in a hazardous situation.

Do not attempt to fell a tree until you have an understanding of the risks and how to

avoid them.

Serious injury could occur to the operator or bystanders while felling a tree.

6

Causes and Operator Prevention of Kickback

Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood

closes in and pinches the saw chain in the cut.

Tip contact in some cases may cause a sudden reverse reaction, kicking the guide bar up and

back towards the operator.

Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back

towards the operator.

Either of these reactions may cause you to lose control of the saw, which could result in

serious personal injury. Do not rely exclusively upon the safety devices built into your saw. As

a chain saw user, you should take several steps to keep your cutting jobs free from accident or

injury.

Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and

can be avoided by taking proper precautions as given below:

•

Maintain a firm grip, with thumbs and fingers encircling the chain saw handles, with

both hands on the saw and position your body and arm to allow you to resist kickback

forces.

Kickback forces can be controlled by the operator, if proper precautions are taken.

Do not let go of the chain saw.

•

Do not overreach and do not cut above shoulder height .

This helps prevent unintended

tip contact and enables better control of the chain saw in unexpected situations.

•

Only use replacement bars and chains specified by the manufacturer.

Incorrect

replacement bars and chains may cause chain breakage and/or kickback

•

Follow the manufacturer’s sharpening and maintenance instructions for the saw chain

.

Decreasing the depth gauge height can lead to increased kickback.

Kickback Safety Devices on This Chain Saw

Chain Brake

The chain saw comes equipped with a chain brake, which stops both the motor and the motion

of the chain when kickback occurs. The chain brake can be activated by the forward motion of

the chain kickback brake handle as the saw rotates backward during kickback.

WARNING

Never modify or attempt to disable the chain brake.

Make sure that the chain brake is working properly before using the chain saw. The chain

kickback brake handle should move back and forth easily.

To test the operation of the chain brake,

perform the following steps (Fig. 1):

•

Place the chain saw on a at bare surface

and make sure no objects or obstructions that

could come in contact with the bar and chain

are in the immediate vicinity.

•

Disengage the chain brake by pulling the

chain kickback brake handle towards the front

handle.

•

Start the chain saw.

•

Push the chain kickback brake handle

towards the front of the saw. A properly

functioning hand brake will stop the

movement of the chain immediately. If the

chain brake is not working properly, do not

use the chain saw until it has been repaired by a qualied service technician.

Fig. 1

Chain kickback brake

handle in operating

position

Chain kickback

brake handle in brake

position

7

WARNING

Confirm that the chain brake works properly before each use.

WARNING

If the chain brake is clogged with wood chips, the function of the

chain brake may deteriorate. Always keep the device clean.

Low Kickback Saw Chain

The rakers (depth gauges) ahead of each cutter can minimize the force of a kickback

reaction by preventing the cutters from digging in too deeply at the kickback zone. Only use

a replacement chain that is equivalent to the original chain or has been certied as a low

kickback chain per ANSI B175.1. A low kickback tooth saw chain is a chain that has met

the kickback performance requirements of ANSI B175.1 (American National Standard for

Power Tools - Gasoline-Powered Chain Saws-Safety Requirements) when tested on the

representative sample of chain saws below 3.8 c.i.d. specied in ANSI B175.1.

CAUTION

As saw chains are sharpened during their useful life, they lose some of the

low kickback qualities and extra caution should be used.

Guide Bar

This saw comes equipped with a guide bar that has a small radius nose. Small radius noses

generally have less potential for kickback. When replacing the guide bar, please order the

guide bar we recommend in this manual or the guide bar with the correct specication with

regarding to this product.

8

ADDITIONAL WARNINGS

A chain saw is intended for two-handed use (Fig. 2).

Serious injury to the operator, helpers,

and/or bystanders can result from one-handed operation.

Make sure that the area in which you are cutting is free from obstructions.

Do not let the

nose of the guide bar contact a log, branch, fence, or any other obstruction that could be hit

while you are operating the saw.

Always cut with the unit running at full speed.

Fully squeeze the switch trigger and maintain

cutting speed.

With a basic understanding of kickback, you can reduce or eliminate the element of

surprise (Fig. 3 – Fig. 5).

Sudden surprise contributes to accidents.

Fig. 2

Fig. 3

Fig. 4

Keep proper footing and balance at all times.

Avoid unintentional contact with the stationary saw chain or guide bar rails.

These can

be very sharp. Always wear gloves and long pants or chaps when handling the chain saw, saw

chain, or guide bar.

Never operate a chain saw that is damaged or improperly adjusted or that is not

completely and securely assembled.

Be sure that the saw chain stops moving when the

trigger switch is released.

Inspect the work piece for nails, wire, or other foreign objects prior to cutting. When

bucking, secure the work piece prior to cutting. When felling or pruning, identify and

secure hazardous branches.

Rotational

Kickback

Danger Zone

Fig. 5

Linear Kickback

Pinch

Kickback

9

Aggressive or abusive cutting or misuse of the chain saw can cause premature bar,

chain, and/or sprocket wear, as well as a broken chain or bar, leading to kickback, chain

throw or the ejection of material.

Never use the guide bar as a lever.

A bent guide bar can cause premature bar, chain, and/ or

sprocket wear, as well as a broken chain or bar, leading to kickback, chain throw or the ejection

of material.

Cut only one work piece at a time.

Push and Pull

– The reaction force is always

opposite to the direction the chain is moving

where wood contact is made. Thus, the

operator must be ready to control the PULL

when cutting on the bottom edge of the bar,

and the PUSH when cutting along the top edge.

See Fig.6.

Plan the work, ensuring an obstacle-free

work area and, in the case of felling, at least

one escape path from the falling tree.

When felling, keep bystanders at least two

tree lengths away.

Do not incinerate the appliance even if it is

severely damaged.

The batteries can explode

in a re.

Do not charge the battery pack in rain or in

wet locations.

Do not expose a battery pack or tool to fire

or excessive temperature. Exposure to fire

or temperature above 212 °F (100°C) may

cause explosion.

If situations occur which are not covered in

this manual, use care and good judgment.

Contact SKIL Customer Service for

assistance.

SAVE THESE INSTRUCTIONS!

Fig. 6

PULL

PUSH

10

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and the explanations with them deserve your careful attention and understanding.

The symbol warnings do not, by themselves, eliminate any danger. The instructions and

warnings they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Owner’s

Manual, including all safety alert symbols such as “DANGER,”

“WARNING,” and “CAUTION” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual

and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to

equipment or other property damage if they are not followed. Each message is preceded by

the word “NOTICE”, as in the example below:

NOTICE: Equipment and/or property damage may result if these instructions are not followed.

WARNING

The operation of any power tools can result in foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always

use eye protection which is marked to comply with ANSI Z87.1.

11

SYMBOLS (CONTINUED)

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and more safely.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

lb Pound Weight

ml Milliliter Volume

.oz Fluid Ounce Volume

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-Hours Battery capacity

Ø Diameter Size of drill bits, grinding wheels, etc.

n

0

No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

…/min

Revolutions or reciprocation

per minute

Revolutions, strokes, surface speed,

orbits, etc. per minute

SPM Strokes Per Minute Stroke speed, at no load

0 Off position Zero speed, zero torque...

°C Celsius temperature Temperature

°F Fahrenheit temperature Temperature

IPX4 Ingress Protection Degree Protection from splashing water

Arrow Action in the direction of arrow

Direct current Type or a characteristic of current

Li-ion RBRC seal

Designates Li-ion battery recycling

program

Read manual symbol Alerts user to read manual

12

Symbol Name Designation/Explanation

Do not expose to rain.

The tool can’t be used in rain or let

outside under raining.

Wear eye protection symbol

Always wear safety goggles or safety

glasses with side shields and a full face

shield when operating this product.

Wear ear protection

Chain saw noise may damage your

hearing. Always wear sound barriers (ear

plugs or ear mufers) to protect your

hearing.

Wear head protection

Wear an approved safety hard hat to

protect your head.

Wear protective gloves

Protect your hands with gloves when

handling saw and saw chain. Heavy-duty,

nonslip gloves improve your grip and

protect your hand.

Two handed hold

Always use two hands when operating the

chain saw.

Guide bar tip kickback

Tip contact can cause the guide bar to

move suddenly upward and backward,

which can cause serious injury.

13

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT: Some of the following symbols for certication information may be used on

your tool. Please study them and learn their meaning. Proper interpretation of these symbols

will allow you to operate the tool better and more safely.

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this component is recognized by

Underwriters Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican

Standards.

14

GET TO KNOW YOUR CHAIN SAW

Guide Bar

Chain Kickback Brake Handle

Lock-off Button

Trigger Switch

Saw Chain

Oil Tank Cap

Oil-Inspection Window

Rear Handle

Front Handle

Chain-Tensioning

Adjusting Knob

Side-cover Knob

Chain Sheath

Storage rail (screws not supplied)

Side Cover

15

Chain Kickback Brake Handle

Serves as the lever for chain brake activation.

It also provides protection against projecting

branches and helps prevent the left hand

from touching the saw chain if it slips off the

front handle.

Trigger Switch

Turns the chain saw On and Off.

Lock-off Button

Helps to prevent accidental or unauthorized

activation of the trigger switch. It must be

depressed before the trigger switch can be

activated.

Oil Tank Cap

Seals the oil tank.

Oil-Inspection Window

Provides a view of the oil level in the oil tank.

Guide Bar

Supports and guides the saw chain.

Chain Sheath

The chain sheath keeps the operator from

coming in contact with the sharp chain blades

when the tool is not in use. It also helps

keep the chain blades from being nicked or

damaged during transportation and storage.

Saw Chain

A loop of chain having cutting teeth that cut

the wood when it is driven by the powerhead

and supported by the guide bar.

Front Handle

The support handle for the left hand at the

front of the saw.

Rear Handle

The support handle for the right hand, located

at the rear of the saw.

Chain-Tensioning Adjusting Knob

Permits precise adjustment of chain tension.

Side Cover

Covers the chain sprocket and secures the

guide bar.

Side-cover Knob

Locks/unlocks the side cover.

Storage Rail

A support object for hanging the saw.

16

SPECIFICATIONS

Model No. CS4562B-00

Rated voltage 20V d.c.

Guide Bar Length 12" (300mm)

Chain Pitch 3/8" (9.5mm) LP

Chain Gauge 0.043" (1.1mm)

Chain Speed 25.9ft/s (7.9m/s)

Oil Tank Capacity 6.8 . oz (200 ml)

Recommended Working Temperature 5–104°F (-15–40°C)

Recommended Storage Temperature 32–104°F (0–40°C)

RECOMMENDED BAR AND CHAIN FOR THIS CHAIN SAW

Part Name Model Number

Guide Bar SBR1200

Saw Chain SCN1200

17

OPERATING INSTRUCTIONS

WARNING

To reduce the risk of fire, personal injury, and product damage due to

a short circuit, never immerse your tool, battery pack, or charger in

fluid or allow a fluid to flow inside them.

Corrosive or conductive uids, such as seawater,

certain industrial chemicals, and bleach or bleach-containing products, etc. can cause a short

circuit.

WARNING

If any parts are damaged or missing, do not operate this product until

the parts are replaced

. Use of this product with damaged or missing parts

could result in serious personal injury.

WARNING

Do not attempt to modify this tool or create accessories not

recommended for use with this tool.

Any such alteration or modication

is misuse and could result in a hazardous condition leading to possible serious injury.

WARNING

To prevent accidental starting that could cause serious personal

injury, always remove the battery pack from the tool when assembling

parts, making adjustments, cleaning, or when not in use.

WARNING

Do not allow familiarity with this product to make you careless.

Remember that a careless fraction of a second is sufcient to inict serious

injury.

WARNING

Always wear eye protection with side shields marked to comply with

ANSI Z87.1, along with hearing protection. Failure to do so could

result in objects being thrown into your eyes and other possibly serious injuries.

Before each use, inspect the entire product for damaged, missing, or loose parts, such as

screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this

product until all missing or damaged parts are replaced.

This cordless chain saw must be used only with the battery packs and charger listed

below:

Battery Pack

Charger

2Ah 2.5Ah 4Ah 5Ah

SKIL BY519701

SKIL BY519702

SKIL

BY519703

SKIL

BY519601

SKIL

BY519603

SKIL SC535801

SKIL QC536001

SKIL SC5358B-02

NOTICE:

Please refer to the battery and charger manuals for detailed operating information.

Application

You may use this product for basic felling, limbing, pruning, and woodcutting of lumber and

trees.

18

Filling Oil Tank with Bar and Chain Lubricant

To Attach/Detach Battery Pack

(Fig. 8)

WARNING

Battery tools are always

in operating condition.

Therefore, remove the battery when

assembling parts, making adjustments,

cleaning, when the tool is not in use, or

when carrying it at your side.

Removing the

battery pack will prevent accidental starting that

could cause serious personal injury.

To attach the battery pack:

Align the raised rib on the battery pack with the

grooves on the tool, and then slide the battery

pack onto the tool.

NOTICE:

Make sure that the latch on the battery pack snaps into place and that the battery

pack is secured to the tool before beginning operation.

NOTICE:

When placing the battery pack onto the tool, be sure that the raised rib on the battery

pack aligns with the groove inside the tool and that the latches snap into place properly.

Improper attachment of the battery pack can cause damage to internal components.

To detach the battery pack:

Depress the battery-release button, located on the front of the battery pack, to release the

battery pack. Pull the battery pack out and remove it from the tool.

To Fill the Oil Tank (Fig. 9)

WARNING

To prevent accidental

starting that could cause

serious personal injury, always remove the

battery pack from the tool before filling the

tank with oil.

WARNING

Do not smoke or bring

any fire or flame near the

oil or the chain saw.

Oil may spill and cause a

re.

NOTICE:

The chain saw is not lled with oil at

the time of purchase. It is essential to ll the

tank with oil before use. Operating the chain

saw without chain oil or when the oil level is

below the minimum mark will result in damage

to the chain saw. Chain life and cutting capacity depend on optimum lubrication. The chain is

automatically lubricated with chain oil during operation.

1.

Remove the battery pack from the chain saw.

2. Clean the oil tank cap and the area around it to ensure that no dirt falls into the oil tank.

3. Position the chain saw on its side on a rm, at surface, so that the tank cap is facing

upwards. Rotate the oil tank cap counterclockwise to remove it (Fig. 9).

4. Carefully pour the bar and chain oil into the tank. Be careful not to let the oil spill from the

opening. Do not overll and leave approximately 13/64’’ (5mm) space between the oil level

and the inside edge of the tank to allow for expansion. Wipe off any excess oil.

5. Replace and fasten the cap.

Fig. 8

Attach

Detach

Battery-Release

Button

Fig. 9

Oil Tank

Cap

19

NOTICE:

•

We recommend using environment-friendly biodegradable chain oil specically intended to

be used with chain saws.

•

Never use oil or other lubricants not specically designed for use on the bar and chain. This

can lead to a clogged oil system, which may cause premature wear of the bar and chain.

•

Check the oil level frequently and ll when the oil level falls below the minimum line. Never

operate the chain saw if the oil is not visible.

•

Do not use dirty, used or otherwise contaminated oil. Damage may occur to the bar or chain.

•

It is normal for oil to seep from the saw when it is not in use. To prevent seepage, empty the

oil tank after each use, and then run the saw for one minute. When storing the tool for a long

period of time, be sure the chain is lightly lubricated; this will prevent rust on the chain and

bar sprocket.

•

To preserve natural resources, please recycle or dispose of oil properly. Consult your local

waste authority for information regarding available recycling and disposal options.

Starting/Stopping the Chain Saw

Before Starting the Chain Saw:

1.

Remove the battery pack.

2.

Make sure that the chain is properly mounted and correctly tensioned.

3.

Check the side-cover knob before use. If it is loose, securely tighten the side-cover knob.

4.

Check the oil level and ll the tank as needed. Make sure the chain is well lubricated.

5.

Check the cutting teeth sharpness of the saw chain.

6.

Make sure that the chain kickback brake handle moves easily to the brake position, then pull

the chain kickback brake handle back towards the front handle to the operating position.

7.

Stand upright and hold the chain saw in a relaxed position.

8.

Hold the chain saw with both hands: with the right hand on the rear handle and the left

hand on the front handle.

9.

Make sure that you have a secure and balanced footing. Watch out for obstacles such as

tree stumps, roots, and ditches, which could cause you to trip or stumble.

10. Make sure the saw chain is not touching the ground or any other objects.

11. Make sure that cutting object does not exceed the usable cutting length of the chain saw. The

tip of guide bar shall always be kept at least 2” (5 cm) outside the outline of the wood log.

To Start the Chain Saw (Fig. 10)

1.

Install the battery pack.

2.

Make sure that no objects or obstructions

that could come in contact with the bar and

chain are in the immediate vicinity.

3.

Pull the chain kickback brake handle

towards the front handle to the operating

position.

4.

Grasp the front and rear handles rmly, using

both hands.

5.

Press and hold the lock-off button, then

squeeze the trigger switch to start the saw.

Release the lock-off button and continue to

squeeze the trigger for continued operation.

Fig. 10

Lock-off Button

Trigger Switch

20

WARNING

Do not attempt to start the saw when the saw chain is in a cut or in

contact with any surface.

To Stop the Chain Saw

1.

Move the chain saw away from cutting area, and then release the trigger switch to stop the

chain saw.

2.

Push the chain kickback brake handle forward to the brake position to engage the chain

brake.

WARNING

Always remove the battery pack from the chain saw during work

breaks and after finishing work.

Preparation for Cutting

Refer to “Safety Warnings” earlier in this manual for appropriate safety equipment.

Work Area Precautions

•

Cut only wood or materials made from wood; do not cut sheet metal, plastics, masonry, or

non-wood building materials.

•

Never allow children to operate the chain saw.

•

Allow no person to use this chain saw who has not read this Operator’s Manual or received

adequate instructions for the safe and proper use of this chain saw.

•

When felling a tree, keep everyone – helpers, bystanders, children, and animals – a safe

distance from the cutting area. During felling operations, the safe distance should be at

least twice the height of the largest trees in the felling area. During bucking operations,

keep a minimum distance of 15 feet (4.5 m) between workers. Trees should not be felled

in a manner that would endanger any person, strike any utility line or cause any property

damage. If a tree does make contact with any utility line, stay clear of the tree and the line

and notify the utility company immediately.

•

Always cut with both feet on solid ground to prevent being pulled off balance.

•

Do not cut above chest height, as a saw held higher is difcult to control against kickback

forces.

•

Do not fell trees near electrical wires or buildings.

•

Cut only when visibility and light are adequate for you to see clearly.

Proper Grip On Handles

•

Wear non-slip gloves for maximum grip and

protection.

•

With the saw on a rm, at surface, hold the

saw rmly with both hands.

•

Always grasp the front handle with the left

hand and the rear handle with the right hand.

•

The ngers should encircle the handle, with

the thumb wrapped under the front handle

(Fig. 11).

WARNING

Never use a cross-handed

grip, or any stance that

could place your body or arm across the

chain line.

Fig. 11

La page charge ...

Skil CS4562B-10 Manuel utilisateur

Skil CS4562B-10 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents