GE Appliances GDF510PGRWW Le manuel du propriétaire

Catégorie
Lave-vaisselle
Taper
Le manuel du propriétaire
Write the model and serial
numbers here:
Model # _________________
Serial # _________________
You can find them on a label on
the tub wall just inside the door.
GE is a trademark of the General Electric Company. Manufactured under trademark license.
OWNER’S MANUAL
DISHWASHERS
49-4000218 Rev 1 05-21 GEA
ENGLISH/FRANÇAIS/
ESPAÑOL
GD*450 – 535 Series
GD*550 – 635 Series
SAFETY INFORMATION .........3
USING THE DISHWASHER
Getting Started ........................5
Dispensers ............................8
Appliance Communication .............10
Loading ............................. 11
CARE AND CLEANING ............17
TROUBLESHOOTING TIPS ......19
LIMITED WARRANTY ...........23
CONSUMER SUPPORT ......... 24
2 49-4000218 Rev 1
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances
product, and we think you will too. Among other things, registration of your appliance ensures that we
can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the
Consumer Support section of this Owners Manual. You may also mail in the pre-printed registration
card included in the packing material.
49-4000218 Rev 1 3
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS
WARNING
For your safety, the information in this manual must be followed to minimize
the risk of fire, explosion, electric shock, and to prevent property damage, personal injury,
or death.
WARNING
PROPER INSTALLATION AND MAINTENANCE
This dishwasher must be properly installed and located in accordance with the Installation Instructions before
it is used. If you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by
visiting our Website at GEAppliances.com. In Canada, visit www.GEAppliances.ca.
Ŷ
Connect the dishwasher/appliance to a grounded
metal, permanent wiring system; or run an
equipment-grounding conductor with the circuit
conductors and connect to the equipment-grounding
terminal or lead of the appliance.
Ŷ
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded.
Ŷ
Detailed grounding instructions can be found in the
“PREPARE ELECTRICAL WIRING” section of the
Installation Instructions.
Ŷ
Dispose of discarded appliances and shipping or
packing material properly.
Ŷ
Do not attempt to repair or replace any part of your
dishwasher unless it is specifically recommended in
this manual. All other servicing should be referred to
a qualified technician.
Ŷ
Use only cord kit WX09X70910 or hard-wire to
building electrical. Failure to follow this instruction,
could result in risk of fire and personal injury.
Ŷ
To minimize the possibility of electric shock,
disconnect this appliance from the power supply
before attempting any maintenance.
NOTE: Turning the dishwasher off does not disconnect
the appliance from the power supply. We recommend
having a qualified technician service your appliance.
WARNING
WHEN USING YOUR DISHWASHER, FOLLOW BASIC PRECAUTIONS,
INCLUDING THE FOLLOWING:
Ŷ
Use this appliance only for its intended purpose as
described in this Owner’s Manual.
Ŷ
Use only detergents or wetting agents
recommended for use in a dishwasher and keep
them out of reach of children. Using a detergent
that is not specifically designed for dishwashers will
cause the dishwasher to fill with suds.
Ŷ
Locate sharp items so that they are not likely to
damage the door seal.
Ŷ
Load sharp knives with the handles up to reduce
the risk of cut-type injuries.
Ŷ
Do not wash plastic items unless marked
dishwasher safe or the equivalent. For plastic
items not so marked, check the manufacturer’s
recommendations.
Ŷ
Do not touch the heating element during or
immediately after use.
Ŷ
Do not operate your dishwasher unless all
enclosure panels are properly in place.
Ŷ
Do not tamper with controls.
Ŷ
Do not abuse, sit on or stand on the door or dish
rack of the dishwasher.
Ŷ
To reduce the risk of injury, do not allow children to
play with, on or inside this appliance at any time.
Ŷ
Do not store or use combustible materials including
gasoline or other flammable liquids or vapors in the
vicinity of this or any other appliance.
Ŷ
Small parts, such as rack clips, can be a choke
hazard to small children if removed from the
dishwasher. Keep out of reach of small children.
4 49-4000218 Rev 1
SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
WARNING
WATER HEATER SAFETY
Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two or more weeks.
HYDROGEN GAS IS EXPLOSIVE.
If the hot water has not been used for two or more weeks, prevent the possibility of damage or injury by turning
on all hot water faucets and allowing them to run for several minutes. Do this before using any electrical
appliance connected to the hot water system. This simple procedure will allow any built-up hydrogen gas to
escape. Since the gas is flammable, do not smoke, use an open flame, or use the appliance during this process.
TO PREVENT MINOR INJURY AND PROPERTY DAMAGE
Ŷ
During or after wash cycle, contents may be hot to
the touch. Use care before handling.
Ŷ
Close supervision is necessary if this appliance is
used by or near children. Do not allow children to
play around the dishwasher when closing the door,
closing the upper rack, or while vertically adjusting
the upper rack due to the possibility of small fingers
being pinched.
Ŷ
Non-Dishware Items: Do not wash items such as
electronic air cleaner filters, furnace filters and
paint brushes in your dishwasher. Damage to the
dishwasher and discoloration or staining of the
dishwasher may result.
Ŷ
Load light-weight, plastic items so they do not
become dislodged and drop to the bottom of the
dishwasher—they might come into contact with the
heating element and be damaged.
WARNING
RISK OF CHILD ENTRAPMENT
PROPER DISPOSAL OF THE DISHWASHER
Junked or abandoned dishwashers are dangerous…even if they will sit for “just a few days.” If you are getting
rid of your dishwasher, please follow the instructions below to help prevent accidents.
Ŷ
Do not allow children to play with, on, or inside this or any discarded appliance.
Ŷ
Take off the door of the washing compartment.
CAUTION
NOTICE
Ŷ ,I\RXUGLVKZDVKHULVFRQQHFWHGWRDZDOOVZLWFK
ensure that the switch is on prior to use.
Ŷ ,I\RXFKRRVHWRWXUQWKHZDOOVZLWFKRIIEHWZHHQ
wash cycles, allow 5-10 seconds after turning the
switch on before touching Start to allow the control
to initialize.
Ŷ
Use only powder, Cascade
®
Platinum™ ActionPacs™ or
Finish
®
Quantum
®
Automatic Dishwashing Detergent,
liquid detergents or rinse agents recommended for
use in a dishwasher and keep them out of the reach
of children. Cascade
®
Platinum™ ActionPacs™ or
Finish
®
Quantum
®
Automatic Dishwashing Detergent,
and Cascade
®
Platinum™ Power Dry™ Rinse Aid
or Finish
®
Jet-Dry
®
Rinse Aid rinse agents have
been
approved for use in all GE Appliances dishwashers.
ELECTRICAL REQUIREMENTS
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electric Code, ANSI/NFPA
70 – latest edition, and all local codes and ordinances.
This appliance must have:
Ŷ
120V, 60Hz, AC-only, 15-ampere or 20-ampere, fused
electrical supply.
Ŷ
Wiring must be 2 wire with ground and rated for 75°C (167°F).
Ŷ
If the electrical supply does not meet the above
requirements, call a licensed electrician before
proceeding.
It is recommended to have:
Ŷ
A circuit breaker or time-delay fuse.
Ŷ
A properly grounded individual branch circuit.
49-4000218 Rev 1 5
USING THE DISHWASHER
Getting started
Features and appearance will vary throughout this manual
Cycle/Select Cycle
Press the Cycle/Select Cycle pad for the desired wash cycle. The light next to the Cycle/Select Cycle pad
will be lit to indicate which wash cycle has been selected.
NOTE: Cycle times vary based on soil level, water temperature, and options selected.
The cycle may be selected with the door in the open position. The cycle will not start until the Start pad is
pressed and the door is closed within 4 seconds.
AutoSense
(on some
models)
This cycle automatically senses the soil level and adjusts the wash cycle accordingly.
*Time range: 1 hour 50 minutes - 2 hours 5 minutes.
Heavy/
Heavy Duty
This cycle is meant for heavily soiled dishes, cookware, pots, or pans with dried-on or baked-on
soils. Everyday dishes are safe to be used in this cycle. This cycle uses improved dry, which can
extend the cycle time. *Time: 2 hours 30 minutes.
Normal/
Everyday
This cycle is meant for daily, regular, or typical use to completely wash a full load of normally
soiled dishes and is designed to conserve both water and energy. Normal/Everyday was used
to rate the energy efficiency of this dishwasher. *Time: 1 hour 20 minutes.
1 Hour/
Time Saver
This cycle is for light to medium soiled dishes and takes about 1 hour. It is safe for china
and crystal with no options selected. NOTE: This cycle does not use Dry. For improved dry
performance, press Dry/Dry Boost option for some models, or select the Normal/Everyday or
Heavy/Heavy Duty cycle. *Time: 60 minutes.
Rinse
(on some
models)
For rinsing partial loads that will be washed later. Do not use detergent. Detergent is not
dispensed during the rinse cycle. *Time: 15 minutes.
*Washing time only. Does not include drying time, Auto Hot Start, or options. NOTE: If the incoming water
temperature is too low, the Auto Hot Start feature may add up to 25 minutes of additional time.
4
Load Dishwasher
For best dishwashing results, follow the loading guidelines found in the Loading section. No pre-rinsing of
normal food soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove
leafy vegetables, meat trimmings, and excessive amounts of grease or oil.
Add Detergent
Add needed amount of detergent to the detergent dispenser. Use high quality detergents such as Cascade
®
Platinum™ ActionPacs™ or Finish
®
Quantum
®
Automatic Dishwashing Detergent. See Dispensers section.
Add Rinse Agent
Add high quality rinse agents such as
Cascade
®
Platinum™ Power Dry™ Rinse Aid or
Finish
®
Jet-Dry
®
Rinse
Aid to the rinse agent dispenser. See Dispensers section. NOTE: The use of rinse aid can further enhance
the dishwasher’s drying performance.
1
2
3
6 49-4000218 Rev 1
Getting started
USING THE DISHWASHER
Select Options
The light by the selected pad will be lit to indicate which Option has been selected.
Wash Temp
Boost/High
(on some
models)
This option increases the temperature to help clean heavily soiled dishes and will increase the
cycle time by 20 to 50 minutes. Option may be turned On or Off during the wash cycle. This
option will also improve dry performance on the Normal/Everyday cycle.
Wash
Temp
Steam/
Steam+
Sani
(on some
models)
This option has several functions. Steam is introduced at the beginning of the cycle to help with
heavily soiled and/or dried-on, baked-on soils and for sanitization of dishware along with improving dry
performance by raising the water temperature in the final rinse. The cycle length will vary depending
on the temperature of your inlet water. This option MUST be selected PRIOR to starting the cycle.
Available with Heavy/Heavy Duty, AutoSense and Normal/Everyday cycles.
NOTE: This option is monitored for sanitization requirements. If the cycle is interrupted during
or after the main wash portion or if the incoming water temperature is so low that adequate
water heating cannot be achieved, the sanitizing conditions may not be met. In these cases, the
Sanitized light will not illuminate at the end of the cycle. Utilizing this option will modify the cycle to
meet the requirements of Section 6, NSF 184 standard for soil removal and sanitization efficacy.
NOTE: Certified residential dishwashers are not intended for licensed food establishments.
Heated
Dry
(on some
models)
This option can be selected by pressing the Dry pad once to illuminate the Heated light. This
setting will greatly improve your dry performance for daily, regular or typical dishes. The heated
dry option will typically add 48 to 64 minutes to your cycle time. This option is not available with
the Rinse cycle. NOTE: The use of rinse aid can further enhance the dishwasher’s drying
performance. On models with this feature, Heated Dry was selected to rate the energy efficiency
of this dishwasher.
Heated
Dry Off
(on some
models)
Shuts off the drying option. Dishes air dry naturally and energy is saved. Opening the door at
the end of the cycle can improve drying performance. NOTE: The use of rinse aid can further
enhance the dishwasher’s drying performance.
Dry Boost
Off (on some models) - Shuts off the drying option. Dishes air dry naturally and energy is saved.
Open the dishwasher door to speed drying.
Normal (on some models) - Turns on the option for faster drying. This option may add up to 64
minutes to the cycle time. This option is not available with the Rinse cycle. On models with this
feature, Dry Boost Normal was selected to rate the energy efficiency of this dishwasher.
High (on some models) - This option can be selected by pressing the Dry Boost pad twice to
illuminate the High light. It will add additional time to your drying option, further enhancing the
dishwasher’s performance for difficult to dry items.
Bottle Jets
(on some
models)
This option increases the time that the bottle jets are on and may add up to 23 minutes to the
cycle time. Use this to wash difficult to clean, dishwasher safe baby bottles, sport bottles, tall
coffee cups, etc. See use recommendations in the Loading section.
Wash
Zones
(on some
models)
Selecting either the Upper or Lower Wash Zones will target dishwashing of just one rack. This
will shorten the cycle time and conserve energy. This option should be used when dishes are
placed in only one rack.
Delay
Hours
(on some
models)
Delays the start of a wash cycle up to 8 to 12 hours depending on model. Press Delay Hours, to
select the number of hours, then press Start one time and close door to begin countdown. The
cycle will start once allotted time has expired.
Lock
Control
(on some
models)
You can lock the controls after you have started a cycle to prevent cycle changes. You can also
lock the controls to prevent selections from being made. For example, children cannot accidentally
start the dishwasher by pressing pads with this option selected.
To LOCK/UNLOCK the dishwasher control, depending on the model, press and hold the Cycle
pad, or the Dry/Dry Boost and Steam pads simultaneously for 3 seconds. The Lock Controls
light will turn on to indicate the control is locked and will turn off to indicate the control is unlocked.
5
49-4000218 Rev 1 7
USING THE DISHWASHER
Getting started
Start Dishwasher
Start Door can be open to select the desired options. Press the Start pad and close the door within
4 seconds to start the cycle or begin the Delay Hours (on some models) countdown. The wash
cycle will begin shortly after closing the door. If the door is opened, the illuminated lights will turn
off if a pad is not pressed within 30 seconds. To activate the display, press any pad.
Interrupt or
Pause
To interrupt or pause a dish cycle, slowly open the door. Opening the door will cause the wash
cycle to pause. The dishwasher will beep every minute to remind you to close the door. To restart
or resume the cycle, press Start, and close the door within 4 seconds.
Cancel To cancel a wash cycle, press and hold the Start pad for 3 seconds and close door.
The dishwasher will drain, emit a beep sound, and the wash cycle light will turn OFF.
6
Cycle Indicator Lights and Sounds
Sanitized
(on some
models)
Displayed at end of the cycle when Wash Temp Steam/Steam+Sani (Sanitize) has been selected and
dishwasher has met requirements for sanitization. See Wash Temp Steam/Steam+Sani, for complete
description. Opening the door or pressing any key while the door is closed will turn off the light.
Clean
(on some
models)
Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are
clean. Opening the door or pressing any key while the door is closed will turn the light off.
Sabbath/
Door
Wake Up
Mode
(on some
models)
To turn this option ON/OFF, press and hold the Cycle Select and Wash Temp pads for 5 seconds,
close the door and wait 3 minutes for the dishwasher to go into sleep mode. In the OFF mode,
the control display, control sounds, and interior lights (on some models) will not respond to the
door opening/closing. This mode can be used when observing certain religious holidays such as
the Sabbath. To activate the control and interior lights (on some models), press any pad.
Mute
(on some
models)
To turn the dishwasher control sounds ON/OFF, press the Heated Dry/Dry Boost pad 7 times
within 5 seconds.
7
8 49-4000218 Rev 1
Check the Water Temperature
The entering water should be at least 120°F (49°C) and
not more than 150°F (66°C) for effective cleaning and to
prevent dish damage. Check the water temperature with a
candy or meat thermometer.
Turn on the hot water faucet nearest the dishwasher,
place the thermometer in a glass and let the water run
continuously into the glass until the temperature stops
rising.
Use a Rinse Agent
High quality rinse agents such as Cascade
®
Platinum™ Power Dry™ Rinse Aid or Finish
®
Jet-Dry
®
Rinse Aid
are designed for great drying action and to protect against spots and film build-up on your dishes, glasses, flatware,
cookware, and plastic.
Filling the Rinse Agent Dispenser
The rinse agent dispenser holds 3.5 oz. (104 ml) of rinse agent. Under normal conditions, this will last approximately
one month.
1
Make sure the dishwasher door is fully open.
2
Open the rinse agent dispenser door.
3
Slowly add rinse agent until the cup is full. You may need to pause several times to
allow rinse aid to settle. NOTE: Indicator window does not light up.
4
Clean up any spilled rinse agent with a damp cloth to prevent foam from forming
inside the dishwasher.
5
Close the rinse agent dispenser door.
Rinse Aid Setting
The amount of rinse agent released into the final wash can be adjusted. If water drops or
hard water spots remain on dishes after the dry cycle, increase the setting.
To adjust the setting
Open the Rinse Agent dispenser door;
then turn the adjuster clockwise to
increase the amount of rinse agent,
counterclockwise to reduce the amount
of rinse agent.
Rinse
agent
adjuster
Clockwise to
reduce water
drops and hard
water spots
Counterclockwise
to reduce foaming
Indicator
window
Dispensers
USING THE DISHWASHER
49-4000218 Rev 1 9
USING THE DISHWASHER
Dispensers
Detergent Dispenser
The detergent dispenser is located in the center of
the dishwasher door. It has two compartments. The
main wash compartment is found inside the detergent
dispenser. To open, press the button on the side of the
dispenser. The pre-wash compartment is on the lid of
the detergent dispenser. Use the pre-wash compartment
only when your water is extremely hard or when you
have a heavy soiled load. The pre-wash compartment is
not used when tablet or packet detergents are used.
NOTE: Do not block detergent dispenser with large or
tall dishware.
You may use tablet, packet, powder, liquid or gel automatic
dishwasher detergent. Make sure you use only detergents
specifically labeled for use in automatic dishwashers. Never
use liquid hand dish detergent in an automatic dishwasher.
Sudsing and poor wash performance will result with the use
of improper detergents.
Detergents should be stored in a dry location and in their
original container to prevent loss of effectiveness. Place
detergent in the cup just prior to starting the dishwasher
and then close the cover. The cover will open during the
wash cycle.
Filling the Detergent Dispenser
GE Appliances recommends using high quality detergent
in tablet or packet form. Independent testing has shown
this form of detergent is very effective in the dishwasher.
Cascade
®
Platinum™ ActionPacs™ or Finish
®
Quantum
®
Powerball
®
are examples of this type of detergent.
However, some single dose detergents are not designed for
shorter cycles. If you experience wash-out issues with these
tablets or packets, follow the instructions below:
Rinsing cycles - DO NOT use detergents. (These cycles
are designed for rinsing dishes only, not soil removal.)
Washing cycles less than 60 minutes (not including
additional dry or wash options) - Put a tablet or
packet into the pre-wash compartment of the detergent
cup, or in the bottom of the dishwasher. (These cycles
are designed to be shorter which could result in bad
detergent wash-out if the detergent is placed in the
main wash compartment of the detergent cup. Wash
performance will be diminished as a result.)
Washing cycles 60 minutes or longer (not including
additional dry or wash options) - Put a tablet or packet
into the main wash compartment of the detergent cup and
close the detergent cup cover. (These cycles are designed
for tougher soils and will likely have more fills/drains than
the shorter cycles. If the tablet or packet is placed in the
pre-wash compartment or tossed in the bottom of the
dishwasher, the detergent will be flushed down the drain
in a very short period of time and will thus be wasted.
Wash performance will be very poor as a result.)
If you choose to use detergent in powder, liquid or gel
form, the amount of detergent you use will be determined
by the hardness of your water, the temperature of your
water, and the food soil load inside the dishwasher.
Contact your water company to get information about the
hardness of the water in your area. Water hardness is
measured in grains per gallon. Use this information and
the table above to determine the amount of detergent to
use. You may purchase a hard water test strip from
GE Appliances. Call 877-959-8688 and ask for part
number WD01X10295. In Canada, call 800-661-1616.
Use the table as a starting point and then adjust the
amount of detergent you use. Use just enough to get
good wash performance. Using just the right amount of
detergent will provide great wash performance without
wasting detergent or etching glassware.
Using too much detergent with very soft and/or very
hot water may cause a condition called etching on your
glassware. Etching is a permanent cloudiness in your
glassware. This condition is irreversible. However, using
too little detergent will cause poor wash performance.
DO NOT USE HAND DISH DETERGENT
NOTE: Using a detergent that is not specifically designed
for dishwashers will cause the dishwasher to fill with suds.
During operation, these suds will spill out of the dishwasher
vents, covering the kitchen floor and making the floor wet.
Because so many detergent containers look alike,
store the dishwasher detergent in a separate space
from all other cleaners. Show anyone who may use the
dishwasher the correct detergent and where it is stored.
While there will be no lasting damage to the dishwasher,
your dishes will not get clean using a dishwashing
detergent that is not formulated for automatic dishwashers.
Number of
Grains/Gal.
Detergent Cup(s) to Fill
Less than 4 Fill cup to 1/3 full
4 to 8 Fill cup to 2/3 full
8 to 12 Fill cup completely full
Greater than 12
Fill both main wash cup and
pre-wash cup
Detergent
Dispenser
Pre-Wash
Main
Wash
Rinse Agent
Push/Slide
to Close
10 49-4000218 Rev 1
USING THE DISHWASHER
Appliance Communication
WiFi Connect (on some models) (for customers in the United States)
Some models are GE Appliances WiFi Connect
capable. A WiFi communciation card is built into the
product allowing it to communicate with your smartphone
for remote monitoring, control and notifications.
Please visit www.GEAppliances.com/connect to
connect your appliance, learn more about connected
appliance features and learn what connected appliance
app’s will work with your smartphone.
WiFi Connectivity: For assistance with the appliance or
the ConnectPlus network connectivity, please call
GE Appliances at 800.220.6899.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Labelling: Changes or modifications to this unit not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
49-4000218 Rev 1 11
On some models, the upper rack may be adjusted to
accommodate larger items. To adjust the upper rack,
fully extend the upper rack and lift the front of the rack
so that the rack roller wheels clear the end hooks on
the front of the rails. Continue to pull the rack until the
remaining rack roller wheels clear the end hook. Select
the set of rollers on the side of the rack that provides the
desired height, and reinstall the upper rack by aligning
the rack roller wheels on the end hook and rack rails –
Ensure that there are roller wheels above and below the
rack rails. Failure to properly align the wheels onto the
end hook and rails may result in the rack falling from the
dishwasher. NOTE: Racks with 4 rollers on each side
are non-adjustable.
USING THE DISHWASHER
Loading
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and
silverware baskets may vary from your model.
Upper Rack
The upper rack is primarily for glasses, cups, and
saucers. For best wash performance, tilt cup and glass
openings toward the center of the rack. Other items such
as pots, pans, and plates may be placed in the upper
rack. This is also a secure place for dishwasher-safe
plastic items. The upper rack can be used for odd sized
utensils. Sauce pans, mixing bowls, and other similarly
shaped items should be placed face down for best wash
performance. Ensure small plastic items are secure so
that they cannot fall on the heater at the bottom of the
dishwasher, potentially damaging the item.
IMPORTANT: Ensure items in the upper rack do not
interfere with the 3rd Rack (on some models) when
loading and unloading.
IMPORTANT: Ensure that items do not protrude through
the bottom of the rack or silverware basket where they
will block the rotation of the middle spray arm. This
could result in noise during operation and/or poor wash
performance.
A loaded upper rack may be
heavier than anticipated. To prevent
minor injury or damage to the contents, do not raise
or lower the upper rack after the rack is loaded.
CAUTION
To add flexibility in loading, the stem safe shelf (on some
models) may be placed in the up or down position or
unfolded and placed in the lower unfolded position.
The shelf may also be used to secure stemware such as
wine glasses. Because these stemware items come in
various sizes, slowly push the rack in to ensure the items
do not bump into the edges of the dishwasher, which
may cause damage to the items.
Place the
slots in the
utility shelf
clips over
the vertical
rack wires
and
push
down to attach
utility shelf
onto
second
wire of rack
Rail
End
Hook
Rack Rollers
Rail
Rail
End
Hook
Pull rack out,
lift up and over
rail end hooks,
and pull out to
remove
Upper
Rack
12 49-4000218 Rev 1
The Bottle Jets system (on some
models) is the ideal location to position
baby bottles, tall sports bottles, or other
tall items with narrow openings. The
Bottle Jets clips hold bottles with small
openings in place so water jets are
directed inside the bottles to clean hard
to reach areas. Clips can be installed
or removed by simply slipping the clip
opening over the top of the nozzle.
USING THE DISHWASHER
Loading
Clip
Nozzle
Bottle Jets
Sports bottle held in place
over a Bottle Jets clip
Baby bottle held in place
under a Bottle Jets clip
Upper Rack - 10 Place Settings - GDF450,
GDF510, GDF511, GDF535, GDT535
Upper Rack - 8 Place Settings - GDF450,
GDF510, GDF511, GDF535, GDT535
Upper Rack
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware
baskets may vary from your model.
Upper Rack - 10 Place Settings - GDT635,
GDF550, GDT550, GDP630, GDT630
Upper Rack - 8 Place Settings - GDT635,
GDF550, GDT550, GDP630, GDT630
49-4000218 Rev 1 13
USING THE DISHWASHER
Loading
Lower Rack
The lower rack is best used for plates, saucers and
cookware items. Large items, such as broiler pans and
baking racks should be placed along the sides of the rack.
If necessary, oversized glasses and mugs can be placed in
the lower rack to maximize loading flexibility. Plates, saucers
and similar items should be placed between the tines in the
direction that allows the item to remain secure in the rack.
IMPORTANT:
It is important to ensure that items do not
protrude through the bottom of the rack or the silverware
basket where they will block the
rotation of the lower spray arm. This
could result in noise during operation
and/or poor wash performance.
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware
baskets may vary from your model.
Lower Rack - 10 Place Settings - GDF450,
GDF510, GDF511, GDF535, GDT535
Lower Rack - 8 Place Settings - GDF450,
GDF510, GDF511, GDF535, GDT535
Lower Rack - 10 Place Settings - GDT635,
GDF550, GDT550, GDP630, GDT630
Lower Rack - 8 Place Settings - GDT635,
GDF550, GDT550, GDP630, GDT630
14 49-4000218 Rev 1
USING THE DISHWASHER
Loading
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and
silverware baskets may vary from your model.
3rd Rack (on some models)
The 3rd rack is the recommended location for large
utensils.
IMPORTANT NOTES:
Ŷ Do not allow cutlery of different materials to touch each
other in the 3rd rack. Doing so may cause discoloration
of the cutlery.
Ŷ The tray is only meant to be used with a GE Appliances
3rd rack dishwasher to hold large utensils, cooking
utensils, and other small items. Using the tray for any
other purpose could result in damage to the tray or
damage to anything interacting with the tray.
Ŷ Ensure that the 3rd rack is fully closed before shutting
the dishwasher door. Shutting the door with the
rack partially extended could cause damage to the
dishwasher.
Take care when loading, unloading,
or transporting the utensil tray.
The tray may contain sharp or heavy items. If items
are dropped from the tray or the tray is dropped,
injury could occur.
The 3rd rack is also removable to allow extra large items to be placed in the upper rack:
To remove the 3rd rack:
1
With the rack fully extended, lift the front of the rack so that
the rack roller wheels clear the end hook
.
2
Continue to pull the rack until the remaining rack roller
wheels clear the end hook.
3
Replace the rack by aligning the rack roller wheels on the
end hook and rack rails – Ensure all roller wheels are
located on top of the rack rails
.
CAUTION
49-4000218 Rev 1 15
USING THE DISHWASHER
Loading
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and
silverware baskets may vary from your model.
Silverware Basket
Place flatware in the removable silverware basket. Sharp
objects, such as forks and knives, may be placed with
the handles facing up, in order to protect your hands.
For the best wash performance, place other items such
as spoons with the handles facing down. Avoid allowing
items to nest together, which may keep them from being
properly washed. When loading, distribute items evenly
in the basket.
The silverware basket may also be used for small items,
such as measuring spoons, baby bottle nipples, plastic
lids, or corn cob holders. The silverware basket covers
(on some models) can be closed to contain small items.
IMPORTANT: Do not load large or tall utensils where
they may block the detergent dispenser, mid spray arm,
or become trapped between the door and the gasket
when the door is closed.
Silverware Basket - 8 Place Settings - GDF450,
GDF510, GDF511, GDF535, GDT535
Silverware Basket - 10 Place Settings - GDF450,
GDF510, GDF511, GDF535, GDT535
Silverware Basket - 8 Place Settings - GDT635,
GDF550, GDT550, GDP630, GDT630
Silverware Basket - 10 Place Settings - GDT635,
GDF550, GDT550, GDP630, GDT630
16 49-4000218 Rev 1
NOTES
Notes
49-4000218 Rev 1 17
Control Panel
To clean the control panel, use a lightly dampened cloth.
Then dry thoroughly.
Dishwasher Interior
To clean and de-odorize your dishwasher, use citric
acid, or Cascade
®
Platinum™ Dishwasher Cleaner or
Finish
®
Dishwasher Cleaner, a detergent additive. They
will break up mineral deposits, and remove hard water
film and stains. You can order citric acid, GE Appliances
kit # WD35X151, through GE Appliances Parts by calling
877-959-8688 or visiting GEApplianceparts.com. In
Canada, call 800-661-1616. You can purchase dishwasher
cleaners at your local grocery store.
Stainless Steel Inner Door and Tub
The stainless steel used to make the dishwasher tub and
inner door provides the highest reliability available in a
GE Appliances dishwasher.
If the dishwasher tub or inner door should be scratched
or dented during normal use, they will not rust or
corrode. These surface blemishes will not affect their
function or durability.
Exterior Door Panel
Before cleaning the front panel, make sure you know
what type of panel you have. Refer to the last two letters
of your model number. You can locate your model
number on the left-hand tub wall just inside the door. If
your model number ends with BB, CC, WW, SA, ES, DS,
TS or FS then you have a painted door panel. If your
model number ends with SS, then you have a Stainless
Steel door panel. If your model number ends with II, then
you have an Integrated door panel.
Follow the instructions below for cleaning the door panel
for your specific model.
Painted/Coated Door Panels
(model numbers ending in BB–black, CC–bisque, WW–
white, SA-silver, ES-slate, DS-black slate, TS-black
stainless steel or FS-fingerprint resistant stainless steel)
DO NOT use Stainless Steel cleaners on the
door surfaces.
Use a clean, soft, lightly dampened cloth, then dry
thoroughly.
Do not use scouring pads or powered cleaners because
these products can scratch the finish.
Stainless Steel Door Panel
(model numbers ending in SS)
For cleaning rust and tarnish, cleaners with oxalic acid
such as Bar Keepers Friend Soft Cleanser™ will remove
rust, tarnish and small blemishes. Use only a liquid
cleanser free of grit and rub in the direction of the brush
lines with a damp soft sponge. Do not use appliance wax
or polish on the stainless steel.
For other blemishes and marks, use Stainless Steel
Magic or a similar product using a clean soft cloth.
Do not use appliance wax, polish, bleach or products
containing chlorine on Stainless Steel. You can
order Stainless Steel Magic # WX10X29 through GE
Appliances Parts by calling 877.959.8688. In Canada,
call 800-661-1616.
Integrated Door Panel (model numbers ending in II)
This is a custom installed door panel, and you will need
to refer to the cabinet manufacturers recommendations
for proper cleaning.
CARE AND CLEANING
Care and cleaning
18 49-4000218 Rev 1
Filters
Inspect and clean the filters periodically. This should be done every other month or more depending on usage. If
there is a decrease in wash performance or dishes feel gritty, this is also an indication the filters need to be cleaned.
Protect Against Freezing
If your dishwasher is left in an unheated place during the winter, ask a service technician to:
1
Turn off electrical power to the dishwasher. Remove
fuses or trip circuit breaker.
2
Turn off the water supply and disconnect the water inlet
line from the water valve.
3
Drain water from the water inlet line and water valve.
(Use a pan to catch the water.)
4
Reconnect the water inlet line to the water valve.
Does Your Dishwasher Have an Air Gap?
An air gap protects your dishwasher
against water backing up into it if a drain
clogs. The air gap is not a part of the
dishwasher. It is not covered by your
warranty. Not all plumbing codes require
air gaps, so you may not have one.
The air gap is easy to clean.
1
Turn off the dishwasher and lift off the air gap cover.
2
Remove the plastic cap under the cover and clean with
a toothpick.
3
Replace the cap and cover when the air gap is clean.
Check the air gap any
time your dishwasher
isn’t draining well.
Air gap
Ultra-Fine Filter Assembly
To clean the Ultra-Fine Filter assembly, remove the
bottom rack. Twist the Ultra-Fine Filter assembly
counterclockwise and lift to remove for cleaning. Rinse
filter with warm soapy water and use a sponge to
carefully remove any stubborn particles.
For models with a 2-piece Ultra-Fine Filter assembly with
an additional Filter Basket for food particles, twist the
Filter Basket in the counterclockwise direction to unlock
it from the Ultra-Fine Filter assembly. See directional
arrows on the bottom of the Filter Basket. Pull the Filter
Basket to remove from the assembly, throw away any
food particles, rinse with warm soapy water, and use a
sponge to remove any stubborn particles.
Once cleaned, replace Filter Basket back into the
Ultra-Fine Filter assembly and twist it clockwise to lock
into place.
Fine Filter
To clean the Fine Filter (mesh plate), remove the bottom
rack. Remove the Ultra-Fine Filter.
Remove the Fine Filter. Rinse filter with warm soapy
water. Scouring pads or brushes can scratch the filter
surface but a soft brush or sponge may be needed to
remove stubborn soils or calcium deposits caused by
hard water. Once cleaned, replace the Fine Filter and
the Ultra-Fine Filter.
Fine
Filter
Spray
Arm
Ultra-Fine
Filter
2-piece - Ultra-fine Filter assembly with additional Filter Basket
(on some models)
CARE AND CLEANING
Care and cleaning
49-4000218 Rev 1 19
Troubleshooting Tips... Before you call for service
TROUBLESHOOTING TIPS
Problem Possible Cause What To Do
Start status
indicator light
flashing
The door was opened or the
cycle was interrupted.
Press the Start pad once and close the door within
4 seconds to start the dishwasher. Press and hold,
for 3 seconds, the Start pad a second time when the
dishwasher is running only if you wish to cancel the
cycle. If problem persists, call for service.
Dishwasher BEEPS
once every minute
(on some models)
This is a reminder that your
dishwasher door has been
left open during operation.
It will continue beeping
until you press Start and
close the door.
Press Start and close the door.
Beeping at the end
of the cycle (on
some models)
This is normal. Dishwasher
will beep twice at the end of
the cycle.
To turn off the double beep indicator (or re-activate it if
it was previously turned off), press the Heated Dry/Dry
Boost pad 7 times within 5 seconds. A triple beep will
sound to indicate the end-of-cycle beep option has been
turned on or off.
Dishes and flatware
not clean
Ultra-Fine Filter assembly
or Fine Filter is clogged
See the Care and Cleaning section.
Low inlet water temperature Make sure inlet water temperature is correct (see the
USING THE DISHWASHER section). Turn on the
hot water faucet nearest the dishwasher, let run until
the water temperature stops rising. Then start the
dishwasher and turn off the faucet. This ensures the
entering water is hot. Select Wash Temp Boost/High if
available.
Water pressure is
temporarily low
Turn on a faucet. Is water coming out more slowly
than usual? If so, wait until pressure is normal before
using your dishwasher. Normal water pressure to the
dishwasher should be 20-120 psi.
Air gap or disposer clogged Clean the air gap or flush the disposer.
High drain loop or air gap
not installed
Refer to the Installation Instructions for proper drain line
installation.
Improper rack loading Make sure large dishware does not block the detergent
dispenser or the wash arms. See the Loading section.
Poor performing detergent Use high quality detergents such as Cascade
®
Platinum™ ActionPacs™ or Finish
®
Quantum
®
Automatic Dishwashing Detergent.
Spots and filming
on glasses and
flatware
Extremely hard water Use high quality rinse agents such as Cascade
®
Platinum™ Power Dry™ Rinse Aid or
Finish
®
Jet-Dry
®
Rinse Aid
to prevent spots and prevent new film
build-up.
If water is extremely hard, a softener may be required.
Low inlet water temperature Make sure water temperature is at least 120°F (49°C).
Overloading or improper
loading of the dishwasher
Load dishwasher as shown in the Loading section.
Old or damp powder
detergent
Make sure detergent is fresh. Use high quality detergents
such as Cascade
®
Platinum™ ActionPacs™ or Finish
®
Quantum
®
Automatic Dishwashing Detergent.
Rinse agent dispenser
empty
Refill with high quality rinse agents such as Cascade
®
Platinum™ Power Dry™ Rinse Aid or Finish
®
Jet-Dry
®
Rinse Aid.
Too little or low performing
detergent
Make sure you use the proper amount of highly rated
detergent.
20 49-4000218 Rev 1
TROUBLESHOOTING TIPS
Troubleshooting Tips... Before you call for service
Problem Possible Cause What To Do
Cloudiness on
glassware
Combination of soft water
and too much detergent
This is called etching and is permanent. To prevent this
from happening, use less detergent if you have soft water.
Wash glassware in the shortest cycle that will get it clean.
Low performing phosphate-
free detergent
See A white film on glassware, dishware and the
interior in this TROUBLESHOOTING section.
Water temperature entering
the dishwasher exceeds
150°F (66°C)
This could be etching. Lower the water heater
temperature.
Suds in the tub Wrong detergent Use only high quality automatic dishwasher detergents to
avoid sudsing. Cascade
®
Platinum™ ActionPacs™ or
Finish
®
Quantum
®
Automatic Dishwashing Detergent
have been approved for use in all GE Appliances
dishwashers.
To remove suds from the tub, open the dishwasher and
let suds dissipate. Pump out water by pressing Start and
close the door. Wait 30 seconds. Open the door, press
and hold Start for 3 seconds, and close the door. Repeat
if necessary.
Rinse agent was spilled Always wipe up rinse agent spills immediately.
Detergent left in
dispenser cups
Dishes are blocking the
detergent cup
Reposition the dishes, so the water from the lower spray
arm can flush the detergent cup. See the Loading section.
Reposition dishware that may be keeping the dispenser
cup door from opening. See the Loading section.
Black or gray marks
on dishes
Aluminum utensils have
rubbed against dishes
Remove marks with a mild, abrasive cleaner.
Dishes don’t dry Low inlet water temperature Make sure inlet water temperature is at least 120°F.
Select Heated Dry or Dry Boost Normal/High.
Use Wash Temp Boost/High.
Select a higher cycle, such as Steam Sani or Heavy/
Heavy Duty.
Rinse agent dispenser is
empty
Check the rinse agent dispenser and fill as required.
Additional drying time is
needed
Leave door closed after the Clean light appears to allow
the fan to run an additional 90 minutes (on some models).
Note: If you open the door, this fan extension will be cancelled.
Cycle selection If using Light/1 Hour/Time Saver cycle which uses
lower water temperature and thus limited dry performance,
switch to a different cycle.
Cycle completion Allow cycles to fully complete. See Long cycle times in
this Troubleshooting Tips section
Long cycle times Dishwasher washes by
alternating mid and lower
spray arms
Longer cycles are normal. For best wash and dry
performance, let cycle complete.
Soil level On some models, the turbidity sensor senses how much
soil is on the dishes. Heavy soiled dish loads will add
more time to the cycle. This is normal function. For best
wash and dry performance, allow cycle to complete.
Control panel
responded to inputs
but dishwasher
never filled with
water
Door may not be completely
closed
Make sure the door is firmly closed.
Water valve may be turned
off
Make sure water valve (usually located under the sink) is
turned on. If problem persists, call for service.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

GE Appliances GDF510PGRWW Le manuel du propriétaire

Catégorie
Lave-vaisselle
Taper
Le manuel du propriétaire