GE Appliances GDF550PGRWW Le manuel du propriétaire

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

You can find them on a label on

the tub wall just inside the door.

GE is a trademark of the General Electric Company. Manufactured under trademark license.

OWNER’S MANUAL

DISHWASHERS

49-4000218 Rev 1 05-21 GEA

ENGLISH/FRANÇAIS/

ESPAÑOL

GD*450 – 535 Series

GD*550 – 635 Series

SAFETY INFORMATION .........3

USING THE DISHWASHER

Getting Started ........................5

Dispensers ............................8

Appliance Communication .............10

Loading ............................. 11

CARE AND CLEANING ............17

TROUBLESHOOTING TIPS ......19

LIMITED WARRANTY ...........23

CONSUMER SUPPORT ......... 24

2 49-4000218 Rev 1

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Register your GE appliance now online. Helpful websites and phone numbers are available in the

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-4000218 Rev 1 3

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

WARNING

For your safety, the information in this manual must be followed to minimize

the risk of fire, explosion, electric shock, and to prevent property damage, personal injury,

or death.

WARNING

PROPER INSTALLATION AND MAINTENANCE

This dishwasher must be properly installed and located in accordance with the Installation Instructions before

it is used. If you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by

visiting our Website at GEAppliances.com. In Canada, visit www.GEAppliances.ca.

Ŷ

Connect the dishwasher/appliance to a grounded

metal, permanent wiring system; or run an

equipment-grounding conductor with the circuit

conductors and connect to the equipment-grounding

terminal or lead of the appliance.

Ŷ

Improper connection of the equipment-grounding

conductor can result in a risk of electric shock.

Check with a qualified electrician or service

representative if you are in doubt whether the

appliance is properly grounded.

Ŷ

Detailed grounding instructions can be found in the

“PREPARE ELECTRICAL WIRING” section of the

Installation Instructions.

Ŷ

Dispose of discarded appliances and shipping or

packing material properly.

Ŷ

Do not attempt to repair or replace any part of your

dishwasher unless it is specifically recommended in

this manual. All other servicing should be referred to

a qualified technician.

Ŷ

Use only cord kit WX09X70910 or hard-wire to

building electrical. Failure to follow this instruction,

could result in risk of fire and personal injury.

Ŷ

To minimize the possibility of electric shock,

disconnect this appliance from the power supply

before attempting any maintenance.

NOTE: Turning the dishwasher off does not disconnect

the appliance from the power supply. We recommend

having a qualified technician service your appliance.

WARNING

WHEN USING YOUR DISHWASHER, FOLLOW BASIC PRECAUTIONS,

INCLUDING THE FOLLOWING:

Ŷ

Use this appliance only for its intended purpose as

described in this Owner’s Manual.

Ŷ

Use only detergents or wetting agents

recommended for use in a dishwasher and keep

them out of reach of children. Using a detergent

that is not specifically designed for dishwashers will

cause the dishwasher to fill with suds.

Ŷ

Locate sharp items so that they are not likely to

damage the door seal.

Ŷ

Load sharp knives with the handles up to reduce

the risk of cut-type injuries.

Ŷ

Do not wash plastic items unless marked

dishwasher safe or the equivalent. For plastic

items not so marked, check the manufacturer’s

recommendations.

Ŷ

Do not touch the heating element during or

immediately after use.

Ŷ

Do not operate your dishwasher unless all

enclosure panels are properly in place.

Ŷ

Do not tamper with controls.

Ŷ

Do not abuse, sit on or stand on the door or dish

rack of the dishwasher.

Ŷ

To reduce the risk of injury, do not allow children to

play with, on or inside this appliance at any time.

Ŷ

Do not store or use combustible materials including

gasoline or other flammable liquids or vapors in the

vicinity of this or any other appliance.

Ŷ

Small parts, such as rack clips, can be a choke

hazard to small children if removed from the

dishwasher. Keep out of reach of small children.

4 49-4000218 Rev 1

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

WARNING

WATER HEATER SAFETY

Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two or more weeks.

HYDROGEN GAS IS EXPLOSIVE.

If the hot water has not been used for two or more weeks, prevent the possibility of damage or injury by turning

on all hot water faucets and allowing them to run for several minutes. Do this before using any electrical

appliance connected to the hot water system. This simple procedure will allow any built-up hydrogen gas to

escape. Since the gas is flammable, do not smoke, use an open flame, or use the appliance during this process.

TO PREVENT MINOR INJURY AND PROPERTY DAMAGE

Ŷ

During or after wash cycle, contents may be hot to

the touch. Use care before handling.

Ŷ

Close supervision is necessary if this appliance is

used by or near children. Do not allow children to

play around the dishwasher when closing the door,

closing the upper rack, or while vertically adjusting

the upper rack due to the possibility of small fingers

being pinched.

Ŷ

Non-Dishware Items: Do not wash items such as

electronic air cleaner filters, furnace filters and

paint brushes in your dishwasher. Damage to the

dishwasher and discoloration or staining of the

dishwasher may result.

Ŷ

Load light-weight, plastic items so they do not

become dislodged and drop to the bottom of the

dishwasher—they might come into contact with the

heating element and be damaged.

WARNING

RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE DISHWASHER

Junked or abandoned dishwashers are dangerous…even if they will sit for “just a few days.” If you are getting

rid of your dishwasher, please follow the instructions below to help prevent accidents.

Ŷ

Do not allow children to play with, on, or inside this or any discarded appliance.

Ŷ

Take off the door of the washing compartment.

CAUTION

NOTICE

Ŷ ,I\RXUGLVKZDVKHULVFRQQHFWHGWRDZDOOVZLWFK

ensure that the switch is on prior to use.

Ŷ ,I\RXFKRRVHWRWXUQWKHZDOOVZLWFKRIIEHWZHHQ

wash cycles, allow 5-10 seconds after turning the

switch on before touching Start to allow the control

to initialize.

Ŷ

Use only powder, Cascade

®

Platinum™ ActionPacs™ or

Finish

®

Quantum

®

Automatic Dishwashing Detergent,

liquid detergents or rinse agents recommended for

use in a dishwasher and keep them out of the reach

of children. Cascade

®

Platinum™ ActionPacs™ or

Finish

®

Quantum

®

Automatic Dishwashing Detergent,

and Cascade

®

Platinum™ Power Dry™ Rinse Aid

or Finish

®

Jet-Dry

®

Rinse Aid rinse agents have

been

approved for use in all GE Appliances dishwashers.

ELECTRICAL REQUIREMENTS

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electric Code, ANSI/NFPA

70 – latest edition, and all local codes and ordinances.

This appliance must have:

Ŷ

120V, 60Hz, AC-only, 15-ampere or 20-ampere, fused

electrical supply.

Ŷ

Wiring must be 2 wire with ground and rated for 75°C (167°F).

Ŷ

If the electrical supply does not meet the above

requirements, call a licensed electrician before

proceeding.

It is recommended to have:

Ŷ

A circuit breaker or time-delay fuse.

Ŷ

A properly grounded individual branch circuit.

49-4000218 Rev 1 5

USING THE DISHWASHER

Getting started

Features and appearance will vary throughout this manual

Cycle/Select Cycle

Press the Cycle/Select Cycle pad for the desired wash cycle. The light next to the Cycle/Select Cycle pad

will be lit to indicate which wash cycle has been selected.

NOTE: Cycle times vary based on soil level, water temperature, and options selected.

The cycle may be selected with the door in the open position. The cycle will not start until the Start pad is

pressed and the door is closed within 4 seconds.

AutoSense

(on some

models)

This cycle automatically senses the soil level and adjusts the wash cycle accordingly.

*Time range: 1 hour 50 minutes - 2 hours 5 minutes.

Heavy/

Heavy Duty

This cycle is meant for heavily soiled dishes, cookware, pots, or pans with dried-on or baked-on

soils. Everyday dishes are safe to be used in this cycle. This cycle uses improved dry, which can

extend the cycle time. *Time: 2 hours 30 minutes.

Normal/

Everyday

This cycle is meant for daily, regular, or typical use to completely wash a full load of normally

soiled dishes and is designed to conserve both water and energy. Normal/Everyday was used

to rate the energy efficiency of this dishwasher. *Time: 1 hour 20 minutes.

1 Hour/

Time Saver

This cycle is for light to medium soiled dishes and takes about 1 hour. It is safe for china

and crystal with no options selected. NOTE: This cycle does not use Dry. For improved dry

performance, press Dry/Dry Boost option for some models, or select the Normal/Everyday or

Heavy/Heavy Duty cycle. *Time: 60 minutes.

Rinse

(on some

models)

For rinsing partial loads that will be washed later. Do not use detergent. Detergent is not

dispensed during the rinse cycle. *Time: 15 minutes.

*Washing time only. Does not include drying time, Auto Hot Start, or options. NOTE: If the incoming water

temperature is too low, the Auto Hot Start feature may add up to 25 minutes of additional time.

4

Load Dishwasher

For best dishwashing results, follow the loading guidelines found in the Loading section. No pre-rinsing of

normal food soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove

leafy vegetables, meat trimmings, and excessive amounts of grease or oil.

Add Detergent

Add needed amount of detergent to the detergent dispenser. Use high quality detergents such as Cascade

®

Platinum™ ActionPacs™ or Finish

®

Quantum

®

Automatic Dishwashing Detergent. See Dispensers section.

Add Rinse Agent

Add high quality rinse agents such as

Cascade

®

Platinum™ Power Dry™ Rinse Aid or

Finish

®

Jet-Dry

®

Rinse

Aid to the rinse agent dispenser. See Dispensers section. NOTE: The use of rinse aid can further enhance

the dishwasher’s drying performance.

1

2

3

6 49-4000218 Rev 1

Getting started

USING THE DISHWASHER

Select Options

The light by the selected pad will be lit to indicate which Option has been selected.

Wash Temp

Boost/High

(on some

models)

This option increases the temperature to help clean heavily soiled dishes and will increase the

cycle time by 20 to 50 minutes. Option may be turned On or Off during the wash cycle. This

option will also improve dry performance on the Normal/Everyday cycle.

Wash

Temp

Steam/

Steam+

Sani

(on some

models)

This option has several functions. Steam is introduced at the beginning of the cycle to help with

heavily soiled and/or dried-on, baked-on soils and for sanitization of dishware along with improving dry

performance by raising the water temperature in the final rinse. The cycle length will vary depending

on the temperature of your inlet water. This option MUST be selected PRIOR to starting the cycle.

Available with Heavy/Heavy Duty, AutoSense and Normal/Everyday cycles.

NOTE: This option is monitored for sanitization requirements. If the cycle is interrupted during

or after the main wash portion or if the incoming water temperature is so low that adequate

water heating cannot be achieved, the sanitizing conditions may not be met. In these cases, the

Sanitized light will not illuminate at the end of the cycle. Utilizing this option will modify the cycle to

meet the requirements of Section 6, NSF 184 standard for soil removal and sanitization efficacy.

NOTE: Certified residential dishwashers are not intended for licensed food establishments.

Heated

Dry

(on some

models)

This option can be selected by pressing the Dry pad once to illuminate the Heated light. This

setting will greatly improve your dry performance for daily, regular or typical dishes. The heated

dry option will typically add 48 to 64 minutes to your cycle time. This option is not available with

the Rinse cycle. NOTE: The use of rinse aid can further enhance the dishwasher’s drying

performance. On models with this feature, Heated Dry was selected to rate the energy efficiency

of this dishwasher.

Heated

Dry Off

(on some

models)

Shuts off the drying option. Dishes air dry naturally and energy is saved. Opening the door at

the end of the cycle can improve drying performance. NOTE: The use of rinse aid can further

enhance the dishwasher’s drying performance.

Dry Boost

Off (on some models) - Shuts off the drying option. Dishes air dry naturally and energy is saved.

Open the dishwasher door to speed drying.

Normal (on some models) - Turns on the option for faster drying. This option may add up to 64

minutes to the cycle time. This option is not available with the Rinse cycle. On models with this

feature, Dry Boost Normal was selected to rate the energy efficiency of this dishwasher.

High (on some models) - This option can be selected by pressing the Dry Boost pad twice to

illuminate the High light. It will add additional time to your drying option, further enhancing the

dishwasher’s performance for difficult to dry items.

Bottle Jets

(on some

models)

This option increases the time that the bottle jets are on and may add up to 23 minutes to the

cycle time. Use this to wash difficult to clean, dishwasher safe baby bottles, sport bottles, tall

coffee cups, etc. See use recommendations in the Loading section.

Wash

Zones

(on some

models)

Selecting either the Upper or Lower Wash Zones will target dishwashing of just one rack. This

will shorten the cycle time and conserve energy. This option should be used when dishes are

placed in only one rack.

Delay

Hours

(on some

models)

Delays the start of a wash cycle up to 8 to 12 hours depending on model. Press Delay Hours, to

select the number of hours, then press Start one time and close door to begin countdown. The

cycle will start once allotted time has expired.

Lock

Control

(on some

models)

You can lock the controls after you have started a cycle to prevent cycle changes. You can also

lock the controls to prevent selections from being made. For example, children cannot accidentally

start the dishwasher by pressing pads with this option selected.

To LOCK/UNLOCK the dishwasher control, depending on the model, press and hold the Cycle

pad, or the Dry/Dry Boost and Steam pads simultaneously for 3 seconds. The Lock Controls

light will turn on to indicate the control is locked and will turn off to indicate the control is unlocked.

5

49-4000218 Rev 1 7

USING THE DISHWASHER

Getting started

Start Dishwasher

Start Door can be open to select the desired options. Press the Start pad and close the door within

4 seconds to start the cycle or begin the Delay Hours (on some models) countdown. The wash

cycle will begin shortly after closing the door. If the door is opened, the illuminated lights will turn

off if a pad is not pressed within 30 seconds. To activate the display, press any pad.

Interrupt or

Pause

To interrupt or pause a dish cycle, slowly open the door. Opening the door will cause the wash

cycle to pause. The dishwasher will beep every minute to remind you to close the door. To restart

or resume the cycle, press Start, and close the door within 4 seconds.

Cancel To cancel a wash cycle, press and hold the Start pad for 3 seconds and close door.

The dishwasher will drain, emit a beep sound, and the wash cycle light will turn OFF.

6

Cycle Indicator Lights and Sounds

Sanitized

(on some

models)

Displayed at end of the cycle when Wash Temp Steam/Steam+Sani (Sanitize) has been selected and

dishwasher has met requirements for sanitization. See Wash Temp Steam/Steam+Sani, for complete

description. Opening the door or pressing any key while the door is closed will turn off the light.

Clean

(on some

models)

Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are

clean. Opening the door or pressing any key while the door is closed will turn the light off.

Sabbath/

Door

Wake Up

Mode

(on some

models)

To turn this option ON/OFF, press and hold the Cycle Select and Wash Temp pads for 5 seconds,

close the door and wait 3 minutes for the dishwasher to go into sleep mode. In the OFF mode,

the control display, control sounds, and interior lights (on some models) will not respond to the

door opening/closing. This mode can be used when observing certain religious holidays such as

the Sabbath. To activate the control and interior lights (on some models), press any pad.

Mute

(on some

models)

To turn the dishwasher control sounds ON/OFF, press the Heated Dry/Dry Boost pad 7 times

within 5 seconds.

7

8 49-4000218 Rev 1

Check the Water Temperature

The entering water should be at least 120°F (49°C) and

not more than 150°F (66°C) for effective cleaning and to

prevent dish damage. Check the water temperature with a

candy or meat thermometer.

Turn on the hot water faucet nearest the dishwasher,

place the thermometer in a glass and let the water run

continuously into the glass until the temperature stops

rising.

Use a Rinse Agent

High quality rinse agents such as Cascade

®

Platinum™ Power Dry™ Rinse Aid or Finish

®

Jet-Dry

®

Rinse Aid

are designed for great drying action and to protect against spots and film build-up on your dishes, glasses, flatware,

cookware, and plastic.

Filling the Rinse Agent Dispenser

The rinse agent dispenser holds 3.5 oz. (104 ml) of rinse agent. Under normal conditions, this will last approximately

one month.

1

Make sure the dishwasher door is fully open.

2

Open the rinse agent dispenser door.

3

Slowly add rinse agent until the cup is full. You may need to pause several times to

allow rinse aid to settle. NOTE: Indicator window does not light up.

4

Clean up any spilled rinse agent with a damp cloth to prevent foam from forming

inside the dishwasher.

5

Close the rinse agent dispenser door.

Rinse Aid Setting

The amount of rinse agent released into the final wash can be adjusted. If water drops or

hard water spots remain on dishes after the dry cycle, increase the setting.

To adjust the setting

Open the Rinse Agent dispenser door;

then turn the adjuster clockwise to

increase the amount of rinse agent,

counterclockwise to reduce the amount

of rinse agent.

Rinse

agent

adjuster

Clockwise to

reduce water

drops and hard

water spots

Counterclockwise

to reduce foaming

Indicator

window

Dispensers

USING THE DISHWASHER

49-4000218 Rev 1 9

USING THE DISHWASHER

Dispensers

Detergent Dispenser

The detergent dispenser is located in the center of

the dishwasher door. It has two compartments. The

main wash compartment is found inside the detergent

dispenser. To open, press the button on the side of the

dispenser. The pre-wash compartment is on the lid of

the detergent dispenser. Use the pre-wash compartment

only when your water is extremely hard or when you

have a heavy soiled load. The pre-wash compartment is

not used when tablet or packet detergents are used.

NOTE: Do not block detergent dispenser with large or

tall dishware.

You may use tablet, packet, powder, liquid or gel automatic

dishwasher detergent. Make sure you use only detergents

specifically labeled for use in automatic dishwashers. Never

use liquid hand dish detergent in an automatic dishwasher.

Sudsing and poor wash performance will result with the use

of improper detergents.

Detergents should be stored in a dry location and in their

original container to prevent loss of effectiveness. Place

detergent in the cup just prior to starting the dishwasher

and then close the cover. The cover will open during the

wash cycle.

Filling the Detergent Dispenser

GE Appliances recommends using high quality detergent

in tablet or packet form. Independent testing has shown

this form of detergent is very effective in the dishwasher.

Cascade

®

Platinum™ ActionPacs™ or Finish

®

Quantum

®

Powerball

®

are examples of this type of detergent.

However, some single dose detergents are not designed for

shorter cycles. If you experience wash-out issues with these

tablets or packets, follow the instructions below:

Rinsing cycles - DO NOT use detergents. (These cycles

are designed for rinsing dishes only, not soil removal.)

Washing cycles less than 60 minutes (not including

additional dry or wash options) - Put a tablet or

packet into the pre-wash compartment of the detergent

cup, or in the bottom of the dishwasher. (These cycles

are designed to be shorter which could result in bad

detergent wash-out if the detergent is placed in the

main wash compartment of the detergent cup. Wash

performance will be diminished as a result.)

Washing cycles 60 minutes or longer (not including

additional dry or wash options) - Put a tablet or packet

into the main wash compartment of the detergent cup and

close the detergent cup cover. (These cycles are designed

for tougher soils and will likely have more fills/drains than

the shorter cycles. If the tablet or packet is placed in the

pre-wash compartment or tossed in the bottom of the

dishwasher, the detergent will be flushed down the drain

in a very short period of time and will thus be wasted.

Wash performance will be very poor as a result.)

If you choose to use detergent in powder, liquid or gel

form, the amount of detergent you use will be determined

by the hardness of your water, the temperature of your

water, and the food soil load inside the dishwasher.

Contact your water company to get information about the

hardness of the water in your area. Water hardness is

measured in grains per gallon. Use this information and

the table above to determine the amount of detergent to

use. You may purchase a hard water test strip from

GE Appliances. Call 877-959-8688 and ask for part

number WD01X10295. In Canada, call 800-661-1616.

Use the table as a starting point and then adjust the

amount of detergent you use. Use just enough to get

good wash performance. Using just the right amount of

detergent will provide great wash performance without

wasting detergent or etching glassware.

Using too much detergent with very soft and/or very

hot water may cause a condition called etching on your

glassware. Etching is a permanent cloudiness in your

glassware. This condition is irreversible. However, using

too little detergent will cause poor wash performance.

DO NOT USE HAND DISH DETERGENT

NOTE: Using a detergent that is not specifically designed

for dishwashers will cause the dishwasher to fill with suds.

During operation, these suds will spill out of the dishwasher

vents, covering the kitchen floor and making the floor wet.

Because so many detergent containers look alike,

store the dishwasher detergent in a separate space

from all other cleaners. Show anyone who may use the

dishwasher the correct detergent and where it is stored.

While there will be no lasting damage to the dishwasher,

your dishes will not get clean using a dishwashing

detergent that is not formulated for automatic dishwashers.

Number of

Grains/Gal.

Detergent Cup(s) to Fill

Less than 4 Fill cup to 1/3 full

4 to 8 Fill cup to 2/3 full

8 to 12 Fill cup completely full

Greater than 12

Fill both main wash cup and

pre-wash cup

Detergent

Dispenser

Pre-Wash

Main

Wash

Rinse Agent

Push/Slide

to Close

10 49-4000218 Rev 1

USING THE DISHWASHER

Appliance Communication

WiFi Connect (on some models) (for customers in the United States)

Some models are GE Appliances WiFi Connect

capable. A WiFi communciation card is built into the

product allowing it to communicate with your smartphone

for remote monitoring, control and notifications.

Please visit www.GEAppliances.com/connect to

connect your appliance, learn more about connected

appliance features and learn what connected appliance

app’s will work with your smartphone.

WiFi Connectivity: For assistance with the appliance or

the ConnectPlus network connectivity, please call

GE Appliances at 800.220.6899.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

Labelling: Changes or modifications to this unit not expressly approved by the manufacturer could void the user’s

authority to operate the equipment.

49-4000218 Rev 1 11

On some models, the upper rack may be adjusted to

accommodate larger items. To adjust the upper rack,

fully extend the upper rack and lift the front of the rack

so that the rack roller wheels clear the end hooks on

the front of the rails. Continue to pull the rack until the

remaining rack roller wheels clear the end hook. Select

the set of rollers on the side of the rack that provides the

desired height, and reinstall the upper rack by aligning

the rack roller wheels on the end hook and rack rails –

Ensure that there are roller wheels above and below the

rack rails. Failure to properly align the wheels onto the

end hook and rails may result in the rack falling from the

dishwasher. NOTE: Racks with 4 rollers on each side

are non-adjustable.

USING THE DISHWASHER

Loading

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and

silverware baskets may vary from your model.

Upper Rack

The upper rack is primarily for glasses, cups, and

saucers. For best wash performance, tilt cup and glass

openings toward the center of the rack. Other items such

as pots, pans, and plates may be placed in the upper

rack. This is also a secure place for dishwasher-safe

plastic items. The upper rack can be used for odd sized

utensils. Sauce pans, mixing bowls, and other similarly

shaped items should be placed face down for best wash

performance. Ensure small plastic items are secure so

that they cannot fall on the heater at the bottom of the

dishwasher, potentially damaging the item.

IMPORTANT: Ensure items in the upper rack do not

interfere with the 3rd Rack (on some models) when

loading and unloading.

IMPORTANT: Ensure that items do not protrude through

the bottom of the rack or silverware basket where they

will block the rotation of the middle spray arm. This

could result in noise during operation and/or poor wash

performance.

A loaded upper rack may be

heavier than anticipated. To prevent

minor injury or damage to the contents, do not raise

or lower the upper rack after the rack is loaded.

CAUTION

To add flexibility in loading, the stem safe shelf (on some

models) may be placed in the up or down position or

unfolded and placed in the lower unfolded position.

The shelf may also be used to secure stemware such as

wine glasses. Because these stemware items come in

various sizes, slowly push the rack in to ensure the items

do not bump into the edges of the dishwasher, which

may cause damage to the items.

Place the

slots in the

utility shelf

clips over

the vertical

rack wires

and

push

down to attach

utility shelf

onto

second

wire of rack

Rail

End

Hook

Rack Rollers

Rail

End

Hook

Pull rack out,

lift up and over

rail end hooks,

and pull out to

remove

Upper

Rack

12 49-4000218 Rev 1

The Bottle Jets system (on some

models) is the ideal location to position

baby bottles, tall sports bottles, or other

tall items with narrow openings. The

Bottle Jets clips hold bottles with small

openings in place so water jets are

directed inside the bottles to clean hard

to reach areas. Clips can be installed

or removed by simply slipping the clip

opening over the top of the nozzle.

USING THE DISHWASHER

Loading

Clip

Nozzle

Bottle Jets

Sports bottle held in place

over a Bottle Jets clip

Baby bottle held in place

under a Bottle Jets clip

Upper Rack - 10 Place Settings - GDF450,

GDF510, GDF511, GDF535, GDT535

Upper Rack - 8 Place Settings - GDF450,

GDF510, GDF511, GDF535, GDT535

Upper Rack

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware

baskets may vary from your model.

Upper Rack - 10 Place Settings - GDT635,

GDF550, GDT550, GDP630, GDT630

Upper Rack - 8 Place Settings - GDT635,

GDF550, GDT550, GDP630, GDT630

49-4000218 Rev 1 13

USING THE DISHWASHER

Loading

Lower Rack

The lower rack is best used for plates, saucers and

cookware items. Large items, such as broiler pans and

baking racks should be placed along the sides of the rack.

If necessary, oversized glasses and mugs can be placed in

the lower rack to maximize loading flexibility. Plates, saucers

and similar items should be placed between the tines in the

direction that allows the item to remain secure in the rack.

IMPORTANT:

It is important to ensure that items do not

protrude through the bottom of the rack or the silverware

basket where they will block the

rotation of the lower spray arm. This

could result in noise during operation

and/or poor wash performance.

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware

baskets may vary from your model.

Lower Rack - 10 Place Settings - GDF450,

GDF510, GDF511, GDF535, GDT535

Lower Rack - 8 Place Settings - GDF450,

GDF510, GDF511, GDF535, GDT535

Lower Rack - 10 Place Settings - GDT635,

GDF550, GDT550, GDP630, GDT630

Lower Rack - 8 Place Settings - GDT635,

GDF550, GDT550, GDP630, GDT630

14 49-4000218 Rev 1

USING THE DISHWASHER

Loading

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and

silverware baskets may vary from your model.

3rd Rack (on some models)

The 3rd rack is the recommended location for large

utensils.

IMPORTANT NOTES:

Ŷ Do not allow cutlery of different materials to touch each

other in the 3rd rack. Doing so may cause discoloration

of the cutlery.

Ŷ The tray is only meant to be used with a GE Appliances

3rd rack dishwasher to hold large utensils, cooking

utensils, and other small items. Using the tray for any

other purpose could result in damage to the tray or

damage to anything interacting with the tray.

Ŷ Ensure that the 3rd rack is fully closed before shutting

the dishwasher door. Shutting the door with the

rack partially extended could cause damage to the

dishwasher.

Take care when loading, unloading,

or transporting the utensil tray.

The tray may contain sharp or heavy items. If items

are dropped from the tray or the tray is dropped,

injury could occur.

The 3rd rack is also removable to allow extra large items to be placed in the upper rack:

To remove the 3rd rack:

1

With the rack fully extended, lift the front of the rack so that

the rack roller wheels clear the end hook

.

2

Continue to pull the rack until the remaining rack roller

wheels clear the end hook.

3

Replace the rack by aligning the rack roller wheels on the

end hook and rack rails – Ensure all roller wheels are

located on top of the rack rails

.

CAUTION

49-4000218 Rev 1 15

USING THE DISHWASHER

Loading

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and

silverware baskets may vary from your model.

Silverware Basket

Place flatware in the removable silverware basket. Sharp

objects, such as forks and knives, may be placed with

the handles facing up, in order to protect your hands.

For the best wash performance, place other items such

as spoons with the handles facing down. Avoid allowing

items to nest together, which may keep them from being

properly washed. When loading, distribute items evenly

in the basket.

The silverware basket may also be used for small items,

such as measuring spoons, baby bottle nipples, plastic

lids, or corn cob holders. The silverware basket covers

(on some models) can be closed to contain small items.

IMPORTANT: Do not load large or tall utensils where

they may block the detergent dispenser, mid spray arm,

or become trapped between the door and the gasket

when the door is closed.

Silverware Basket - 8 Place Settings - GDF450,

GDF510, GDF511, GDF535, GDT535

Silverware Basket - 10 Place Settings - GDF450,

GDF510, GDF511, GDF535, GDT535

Silverware Basket - 8 Place Settings - GDT635,

GDF550, GDT550, GDP630, GDT630

Silverware Basket - 10 Place Settings - GDT635,

GDF550, GDT550, GDP630, GDT630

16 49-4000218 Rev 1

NOTES

Notes

49-4000218 Rev 1 17

Control Panel

To clean the control panel, use a lightly dampened cloth.

Then dry thoroughly.

Dishwasher Interior

To clean and de-odorize your dishwasher, use citric

acid, or Cascade

®

Platinum™ Dishwasher Cleaner or

Finish

®

Dishwasher Cleaner, a detergent additive. They

will break up mineral deposits, and remove hard water

film and stains. You can order citric acid, GE Appliances

kit # WD35X151, through GE Appliances Parts by calling

877-959-8688 or visiting GEApplianceparts.com. In

Canada, call 800-661-1616. You can purchase dishwasher

cleaners at your local grocery store.

Stainless Steel Inner Door and Tub

The stainless steel used to make the dishwasher tub and

inner door provides the highest reliability available in a

GE Appliances dishwasher.

If the dishwasher tub or inner door should be scratched

or dented during normal use, they will not rust or

corrode. These surface blemishes will not affect their

function or durability.

Exterior Door Panel

Before cleaning the front panel, make sure you know

what type of panel you have. Refer to the last two letters

of your model number. You can locate your model

number on the left-hand tub wall just inside the door. If

your model number ends with BB, CC, WW, SA, ES, DS,

TS or FS then you have a painted door panel. If your

model number ends with SS, then you have a Stainless

Steel door panel. If your model number ends with II, then

you have an Integrated door panel.

Follow the instructions below for cleaning the door panel

for your specific model.

Painted/Coated Door Panels

(model numbers ending in BB–black, CC–bisque, WW–

white, SA-silver, ES-slate, DS-black slate, TS-black

stainless steel or FS-fingerprint resistant stainless steel)

DO NOT use Stainless Steel cleaners on the

door surfaces.

Use a clean, soft, lightly dampened cloth, then dry

thoroughly.

Do not use scouring pads or powered cleaners because

these products can scratch the finish.

Stainless Steel Door Panel

(model numbers ending in SS)

For cleaning rust and tarnish, cleaners with oxalic acid

such as Bar Keepers Friend Soft Cleanser™ will remove

rust, tarnish and small blemishes. Use only a liquid

cleanser free of grit and rub in the direction of the brush

lines with a damp soft sponge. Do not use appliance wax

or polish on the stainless steel.

For other blemishes and marks, use Stainless Steel

Magic or a similar product using a clean soft cloth.

Do not use appliance wax, polish, bleach or products

containing chlorine on Stainless Steel. You can

order Stainless Steel Magic # WX10X29 through GE

Appliances Parts by calling 877.959.8688. In Canada,

call 800-661-1616.

Integrated Door Panel (model numbers ending in II)

This is a custom installed door panel, and you will need

to refer to the cabinet manufacturers recommendations

for proper cleaning.

CARE AND CLEANING

Care and cleaning

18 49-4000218 Rev 1

Filters

Inspect and clean the filters periodically. This should be done every other month or more depending on usage. If

there is a decrease in wash performance or dishes feel gritty, this is also an indication the filters need to be cleaned.

Protect Against Freezing

If your dishwasher is left in an unheated place during the winter, ask a service technician to:

1

Turn off electrical power to the dishwasher. Remove

fuses or trip circuit breaker.

2

Turn off the water supply and disconnect the water inlet

line from the water valve.

3

Drain water from the water inlet line and water valve.

(Use a pan to catch the water.)

4

Reconnect the water inlet line to the water valve.

Does Your Dishwasher Have an Air Gap?

An air gap protects your dishwasher

against water backing up into it if a drain

clogs. The air gap is not a part of the

dishwasher. It is not covered by your

warranty. Not all plumbing codes require

air gaps, so you may not have one.

The air gap is easy to clean.

1

Turn off the dishwasher and lift off the air gap cover.

2

Remove the plastic cap under the cover and clean with

a toothpick.

3

Replace the cap and cover when the air gap is clean.

Check the air gap any

time your dishwasher

isn’t draining well.

Air gap

Ultra-Fine Filter Assembly

To clean the Ultra-Fine Filter assembly, remove the

bottom rack. Twist the Ultra-Fine Filter assembly

counterclockwise and lift to remove for cleaning. Rinse

filter with warm soapy water and use a sponge to

carefully remove any stubborn particles.

For models with a 2-piece Ultra-Fine Filter assembly with

an additional Filter Basket for food particles, twist the

Filter Basket in the counterclockwise direction to unlock

it from the Ultra-Fine Filter assembly. See directional

arrows on the bottom of the Filter Basket. Pull the Filter

Basket to remove from the assembly, throw away any

food particles, rinse with warm soapy water, and use a

sponge to remove any stubborn particles.

Once cleaned, replace Filter Basket back into the

Ultra-Fine Filter assembly and twist it clockwise to lock

into place.

Fine Filter

To clean the Fine Filter (mesh plate), remove the bottom

rack. Remove the Ultra-Fine Filter.

Remove the Fine Filter. Rinse filter with warm soapy

water. Scouring pads or brushes can scratch the filter

surface but a soft brush or sponge may be needed to

remove stubborn soils or calcium deposits caused by

hard water. Once cleaned, replace the Fine Filter and

the Ultra-Fine Filter.

Fine

Filter

Spray

Arm

Ultra-Fine

Filter

2-piece - Ultra-fine Filter assembly with additional Filter Basket

(on some models)

CARE AND CLEANING

Care and cleaning

49-4000218 Rev 1 19

Troubleshooting Tips... Before you call for service

TROUBLESHOOTING TIPS

Problem Possible Cause What To Do

Start status

indicator light

flashing

The door was opened or the

cycle was interrupted.

Press the Start pad once and close the door within

4 seconds to start the dishwasher. Press and hold,

for 3 seconds, the Start pad a second time when the

dishwasher is running only if you wish to cancel the

cycle. If problem persists, call for service.

Dishwasher BEEPS

once every minute

(on some models)

This is a reminder that your

dishwasher door has been

left open during operation.

It will continue beeping

until you press Start and

close the door.

Press Start and close the door.

Beeping at the end

of the cycle (on

some models)

This is normal. Dishwasher

will beep twice at the end of

the cycle.

To turn off the double beep indicator (or re-activate it if

it was previously turned off), press the Heated Dry/Dry

Boost pad 7 times within 5 seconds. A triple beep will

sound to indicate the end-of-cycle beep option has been

turned on or off.

Dishes and flatware

not clean

Ultra-Fine Filter assembly

or Fine Filter is clogged

See the Care and Cleaning section.

Low inlet water temperature Make sure inlet water temperature is correct (see the

USING THE DISHWASHER section). Turn on the

hot water faucet nearest the dishwasher, let run until

the water temperature stops rising. Then start the

dishwasher and turn off the faucet. This ensures the

entering water is hot. Select Wash Temp Boost/High if

available.

Water pressure is

temporarily low

Turn on a faucet. Is water coming out more slowly

than usual? If so, wait until pressure is normal before

using your dishwasher. Normal water pressure to the

dishwasher should be 20-120 psi.

Air gap or disposer clogged Clean the air gap or flush the disposer.

High drain loop or air gap

not installed

Refer to the Installation Instructions for proper drain line

installation.

Improper rack loading Make sure large dishware does not block the detergent

dispenser or the wash arms. See the Loading section.

Poor performing detergent Use high quality detergents such as Cascade

®

Platinum™ ActionPacs™ or Finish

®

Quantum

®

Automatic Dishwashing Detergent.

Spots and filming

on glasses and

flatware

Extremely hard water Use high quality rinse agents such as Cascade

®

Platinum™ Power Dry™ Rinse Aid or

Finish

®

Jet-Dry

®

Rinse Aid

to prevent spots and prevent new film

build-up.

If water is extremely hard, a softener may be required.

Low inlet water temperature Make sure water temperature is at least 120°F (49°C).

Overloading or improper

loading of the dishwasher

Load dishwasher as shown in the Loading section.

Old or damp powder

detergent

Make sure detergent is fresh. Use high quality detergents

such as Cascade

®

Platinum™ ActionPacs™ or Finish

®

Quantum

®

Automatic Dishwashing Detergent.

Rinse agent dispenser

empty

Refill with high quality rinse agents such as Cascade

®

Platinum™ Power Dry™ Rinse Aid or Finish

®

Jet-Dry

®

Rinse Aid.

Too little or low performing

detergent

Make sure you use the proper amount of highly rated

detergent.

20 49-4000218 Rev 1

TROUBLESHOOTING TIPS

Troubleshooting Tips... Before you call for service

Problem Possible Cause What To Do

Cloudiness on

glassware

Combination of soft water

and too much detergent

This is called etching and is permanent. To prevent this

from happening, use less detergent if you have soft water.

Wash glassware in the shortest cycle that will get it clean.

Low performing phosphate-

free detergent

See A white film on glassware, dishware and the

interior in this TROUBLESHOOTING section.

Water temperature entering

the dishwasher exceeds

150°F (66°C)

This could be etching. Lower the water heater

temperature.

Suds in the tub Wrong detergent Use only high quality automatic dishwasher detergents to

avoid sudsing. Cascade

®

Platinum™ ActionPacs™ or

Finish

®

Quantum

®

Automatic Dishwashing Detergent

have been approved for use in all GE Appliances

dishwashers.

To remove suds from the tub, open the dishwasher and

let suds dissipate. Pump out water by pressing Start and

close the door. Wait 30 seconds. Open the door, press

and hold Start for 3 seconds, and close the door. Repeat

if necessary.

Rinse agent was spilled Always wipe up rinse agent spills immediately.

Detergent left in

dispenser cups

Dishes are blocking the

detergent cup

Reposition the dishes, so the water from the lower spray

arm can flush the detergent cup. See the Loading section.

Reposition dishware that may be keeping the dispenser

cup door from opening. See the Loading section.

Black or gray marks

on dishes

Aluminum utensils have

rubbed against dishes

Remove marks with a mild, abrasive cleaner.

Dishes don’t dry Low inlet water temperature Make sure inlet water temperature is at least 120°F.

Select Heated Dry or Dry Boost Normal/High.

Use Wash Temp Boost/High.

Select a higher cycle, such as Steam Sani or Heavy/

Heavy Duty.

Rinse agent dispenser is

empty

Check the rinse agent dispenser and fill as required.

Additional drying time is

needed

Leave door closed after the Clean light appears to allow

the fan to run an additional 90 minutes (on some models).

Note: If you open the door, this fan extension will be cancelled.

Cycle selection If using Light/1 Hour/Time Saver cycle which uses

lower water temperature and thus limited dry performance,

switch to a different cycle.

Cycle completion Allow cycles to fully complete. See Long cycle times in

this Troubleshooting Tips section

Long cycle times Dishwasher washes by

alternating mid and lower

spray arms

Longer cycles are normal. For best wash and dry

performance, let cycle complete.

Soil level On some models, the turbidity sensor senses how much

soil is on the dishes. Heavy soiled dish loads will add

more time to the cycle. This is normal function. For best

wash and dry performance, allow cycle to complete.

Control panel

responded to inputs

but dishwasher

never filled with

water

Door may not be completely

closed

Make sure the door is firmly closed.

Water valve may be turned

off

Make sure water valve (usually located under the sink) is

turned on. If problem persists, call for service.

La page charge ...

GE Appliances GDF550PGRWW Le manuel du propriétaire

GE Appliances GDF550PGRWW Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents