NAPOLEON NEFI27H-CTC Le manuel du propriétaire
- Catégorie
- Cheminées
- Taper
- Le manuel du propriétaire
ADD MANUAL TITLE
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone (705)721-1212 • Fax (705)720-9081 • www.napoleonfi replaces.com • hearth@napoleonproducts.com
CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:
CSA 2.22 NO. 46 / UL 1278
INSTALLER:
Leave this manual with the appliance
CONSUMER:
Retain this manual for future reference
PRODUCT NAME™
ADD PRODUCT CODE
(IF MULTIPLE, _____ ILLUSTRATED)
MULTIPLE PRODUCT CODES (LEAVE BLANK IF N/A)
ADD PRODUCT IMAGE
CSA /
INTERTEK
LOGO
SAFETY INFORMATION
- Do not store or use gasoline or other
fl ammable vapors and liquids in the vicinity of
this or any other appliance.
FIRE OR EXPLOSION HAZARD
If the information in these instructions are
not followed exactly, a fi re or explosion may
result causing property damage, personal
injury, or loss of life.
WARNING
!
ENGLISH
$10.00
FOR INDOOR USE ONLY
INSTALLATION AND
OPERATION MANUAL
NAPOLEON 27” LOGSET
NEFI27H-CTC
FRENCH PG. 23
W415-1719 / C / 04.07.17
W415-1719 / C / 04.07.17
EN
2
safety information
• If equipped with a heater, this appliance
can be hot when operated and can cause
severe burns if contacted.
• Do not operate appliance before reading and
understanding operating instructions. Failure
to operate appliance according to operating
instructions could cause fi re or injury.
• Do not install damaged, incomplete or
substitute components.
• Do not burn wood or other materials in this
appliance.
• All electric appliances have hot and arcing or
sparking parts inside. Do not use it in areas
where a gas line, paint or fl ammable liquids are present.
• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
• It is imperative that the control compartments, circulating blower and its passageway in the appliance
are kept clean. The appliance should be inspected before use and at least annually by a qualifi ed service
person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material,
etc. The appliance area must be kept clear and free from combustible materials, gasoline and other
fl ammable vapors and liquids.
• Under no circumstances should this appliance be modifi ed.
• Do not use this appliance if any part has been under water. Immediately call a qualifi ed service technician to
inspect the appliance and to replace any part of the control system which has been under water.
• If equipped with a glass door, do not operate the appliance with the glass door removed, cracked or
broken. Replacement of the glass should be done by a licensed or qualifi ed service person.
• If equipped with a glass door, do not strike or slam shut the appliance glass door.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As
with all plastic bags, these are not toys and should be kept away from children and infants.
• Servicing should be done only while the appliance is disconnected from the power supply circuit.
• Always unplug appliance when not in use.
• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been
dropped or damaged in any manner. Return appliance to authorized service facility for examination,
electrical or mechanical adjustment, or repair.
• Do not use outdoors.
• Never locate appliance where it may fall into a bathtub or other water container.
• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord
away from traffi c area and where it will not be tripped over.
• Connect to properly grounded outlets only.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
electric shock or fi re, or damage the appliance.
LA VITRE CHAUDE CAUSERA
DES BRÛLURES.
NE PAS TOUCHER LA VITRE
AVANT QU’ELLE AIT REFROIDI.
NE JAMAIS LAISSER LES
ENFANTS TOUCHER LA VITRE.
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
DANGER
!
AVERTISSEMENT
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and
shall be installed for the protection of children and other
at-risk individuals.
Une barriére conçu à réduire le risque de brûlures
causées par le verre chaud est fourni avec l’appareil et
sera installé pour la protection des enfants et d’autres
personnes à risque.
3.2A
• To prevent a possible fi re, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like
a carpet, where openings may become blocked.
• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or relocatable
power tap (outlet/power strip).
• These appliances are tested and listed for use only with the optional accessories listed in these instructions.
Use of optional accessories not specifi cally tested for this appliance could void the warranty and/or result in
a safety hazard.
For appliances equipped with a heater:
• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before
servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.
• Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is
recommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install
an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and
away from hot surfaces.
• Clothing or other fl ammable material should not be placed on or near the appliance.
• Due to high temperatures, the appliance should be located out of traffi c and away from furniture and draperies.
• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.
• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from
hot surfaces. These screens and guards must be fastened to the fl oor.
• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.
Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or
damage to decorations, a T.V. or other electronic components.
!
WARNING
!
WARNING
EN
W415-1719 / C / 04.07.17
3
safety information
• If equipped with a heater, this appliance
can be hot when operated and can cause
severe burns if contacted.
• Do not operate appliance before reading and
understanding operating instructions. Failure
to operate appliance according to operating
instructions could cause fi re or injury.
• Do not install damaged, incomplete or
substitute components.
• Do not burn wood or other materials in this
appliance.
• All electric appliances have hot and arcing or
sparking parts inside. Do not use it in areas
where a gas line, paint or fl ammable liquids are present.
• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
• It is imperative that the control compartments, circulating blower and its passageway in the appliance
are kept clean. The appliance should be inspected before use and at least annually by a qualifi ed service
person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material,
etc. The appliance area must be kept clear and free from combustible materials, gasoline and other
fl ammable vapors and liquids.
• Under no circumstances should this appliance be modifi ed.
• Do not use this appliance if any part has been under water. Immediately call a qualifi ed service technician to
inspect the appliance and to replace any part of the control system which has been under water.
• If equipped with a glass door, do not operate the appliance with the glass door removed, cracked or
broken. Replacement of the glass should be done by a licensed or qualifi ed service person.
• If equipped with a glass door, do not strike or slam shut the appliance glass door.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As
with all plastic bags, these are not toys and should be kept away from children and infants.
• Servicing should be done only while the appliance is disconnected from the power supply circuit.
• Always unplug appliance when not in use.
• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been
dropped or damaged in any manner. Return appliance to authorized service facility for examination,
electrical or mechanical adjustment, or repair.
• Do not use outdoors.
• Never locate appliance where it may fall into a bathtub or other water container.
• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord
away from traffi c area and where it will not be tripped over.
• Connect to properly grounded outlets only.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
electric shock or fi re, or damage the appliance.
LA VITRE CHAUDE CAUSERA
DES BRÛLURES.
NE PAS TOUCHER LA VITRE
AVANT QU’ELLE AIT REFROIDI.
NE JAMAIS LAISSER LES
ENFANTS TOUCHER LA VITRE.
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
DANGER
!
AVERTISSEMENT
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and
shall be installed for the protection of children and other
at-risk individuals.
Une barriére conçu à réduire le risque de brûlures
causées par le verre chaud est fourni avec l’appareil et
sera installé pour la protection des enfants et d’autres
personnes à risque.
3.2A
• To prevent a possible fi re, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like
a carpet, where openings may become blocked.
• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or relocatable
power tap (outlet/power strip).
• These appliances are tested and listed for use only with the optional accessories listed in these instructions.
Use of optional accessories not specifi cally tested for this appliance could void the warranty and/or result in
a safety hazard.
For appliances equipped with a heater:
• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before
servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.
• Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is
recommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install
an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and
away from hot surfaces.
• Clothing or other fl ammable material should not be placed on or near the appliance.
• Due to high temperatures, the appliance should be located out of traffi c and away from furniture and draperies.
• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.
• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from
hot surfaces. These screens and guards must be fastened to the fl oor.
• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.
Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or
damage to decorations, a T.V. or other electronic components.
!
WARNING
!
WARNING
W415-1719 / C / 04.07.17
EN
4
table of contents
1.0 general information 5
1.1 listing approvals 5
1.2 rating plate information 5
1.3 label location 6
2.0 dimensions 7
3.0 locating log set 8
3.1 unpacking and testing log set 8
3.2 grounding log set 8
4.0 installation 9
4.1 log set installation 9
4.1.1 installing log set into existing fireplace 9
4.1.2 installing log set into mantel 10
4.2 hard wiring installation 11
4.3 securing the log set 12
5.0 finishing 13
5.1 log placement 13
6.0 operating instructions 14
6.1 operating control panel 14
6.2 operating by remote control 15
6.3 remote battery installation 15
7.0 wiring diagram 16
8.0 replacements 17
8.1 overview 18
9.0 troubleshooting 19
10.0 warranty 20
11.0 notes 21
The camera icon indicates video tutorials are available as additional reference, visit
http://mynapoleon.napoleonproducts.com/download/index/44/1
Changes, other than editorial, are denoted by a vertical line in the margin
note:
EN
W415-1719 / C / 04.07.17
5
general information
Description
27” Electric Log Set Insert
Voltage
120V AC
Watts
Max 1500W
Amps
15 AMP Grounded Circuit
Appliance Width
27” (68.6cm)
Appliance Height
15 1/2” (39.3cm)
Appliance Depth
12 7/16” (31.7cm)
Net Weight
23.8lbs (10.8kg)
Gross Weight
31.5lbs (14.3kg)
NEFI27H-CTC
1.0 general information
This log set has been tested in accordance with the CSA Standards for fixed and location-dedicated electric room
appliances in the United States and Canada. If you need assistance during installation, please contact your local
dealer.
note:
This log set must be electrically wired and gorunded in accordance with local codes or, in the absence of
local codes, with National Electric Code ANSI/NFPA 70-latest edition in the United States or the Canadian
Electric Code, CSA C22.1 in Canada.
This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.
For rating plate location, see “label location” section.
W385-4473
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARD: CSA 22.2 NO. 46 AND UL 1278 /
HOMOLOGUÉ SELON LES NORMES NATIONALES CANADIENNES ET AMÉRICAINES:CSA 22.2 NO. 46 UL 1278
Page 1 of 1
ELECTRIC FIREPLACE. SUITABLE FOR
BEDROOM AND BED-SITTING ROOM
INSTALLATION. SUITABLE FOR MOBILE
HOME INSTALLATION.
VOLTAGE: 120 VAC TENSION: 120VCA
FREQUENCY: 60Hz FRÉQUENCE: 60Hz
POWER: 1500W PUISSANCE: 1500W
DATE CODE: XXXXX CODE DE DATE:
DESIGNED IN NORTH AMERICA
BY WOLF STEEL LTD.
MADE IN CHINA FABRIQUÉ EN CHINE
WOLF STEEL LTD.
24 NAPOLEON ROAD,
BARRIE, ON, L4M 0G8 CANADA
SERIAL NUMBER/NO. DE SÉRIE:
NEFI27
MATERIAL: CLASS IIIA-2 PERMANENT LEXAN ADHESIVE LABEL, MINIMUM THICKNESS 0.1MM, NON WATER SOLUBLE ADHESIVE CAPABLE OF WITHSTANDING A
MAXIMUM TEMPERATURE OF 175°F (79°C).
SPECIFICATION: BLACK LETTERING ON WHITE BACKGROUND. FONT SIZE TO BE MINIMUM OF 8.5 PT (3.2mm)
MAX OVERALL SIZE: 6" x 2.5"
SERIAL NUMBERS TO BE ASCENDING FROM LAST NUMBER RELEASED ON W385-2066
TITLE: RATING PLATE NEFI27H / NEFI27H-CTC
REVISION:
DWG#: W385-4473
DATE: 02.09.17_H.W.
DÉSIGNÉ EN AMÉRIQUE DU
NORD PAR WOLF STEEL LTD.
MASTER CONTRACT: 161746
CONTRAT-CADRE: 161746
MODEL / MODÈLE:
NEFI27H
NEFI27H-CTC
FOYER ÉLECTRIQUE. HOMOLOGUÉ POUR
INSTALLATION DANS UNE CHAMBRE À
COUCHER, UNE SALLE DE BAIN ET UN
STUDIO. APPROPRIÉE POUR INSTALLATION
DANS UNE MAISON MOBILE.
SAMPLE
The rating plate must remain with the appliance at all times. It must not be removed.
note:
Do not use the log set during mobile transportation.
note:
1.1 listing approvals
1.2 rating plate information
W415-1719 / C / 04.07.17
EN
6
general information
1.3 label location
CAUTION LABEL
(W385-1945)
"DO NOT COVER"
LABEL (W385-1946)
WARNING LABEL
(W385-1943)
FRONT
RIGHT SIDE
LEFT SIDE
WARNING LABEL
(W385-1944)
RATING PLATE WITH
SERIAL NUMBER
NEFI27H (W385-4473)
ATTENTION LABEL
(W385-2133)
EN
W415-1719 / C / 04.07.17
7
dimensions
2.0 dimensions
27"
685mm
8 11/16"
221mm
12 7/16"
317mm
15 1/2"
393mm
1 7/16"
36mm
19"
483mm
HARDWIRE JUNCTION
BOX OR CORD
FRONT VIEW RIGHT SIDE VIEW TOP VIEW
W415-1719 / C / 04.07.17
EN
8
locating log set
3.0 locating log set
3.1 unpacking and testing log set
3.2 grounding log set
• Due to high temperatures, this electric appliance should be located out of traffic. Keep combustible materials
such as furniture, pillows, bedding, papers, clothes and curtains at least 36” (91.4cm) from the front of the
appliance.
• Never locate this electric appliance where it may fall into a bathtub or other water container.
• Wear safety gloves and safety glasses for protection during installation and maintenance.
• To prevent contact with sagging or loose insulation, the electric appliance must not be installed against vapor
barrier or exposed insulation. Localized overheating could occur and a fire could result.
• Do not expose the electric appliance to the elements (such as rain, etc.).
!
WARNING
Carefully remove the appliance from the box and remove the support brackets. Prior to installing the appliance,
remove all packaging material and test to make sure the appliance operates properly by plugging the power
supply cord into a conveniently located 120V, 15Amp minimum grounded outlet.
51.1
Grounding Methods
Metal Screw
(A)
Not allowed in Canada
Grounding Means
Adapter
Grounding Pin
Cover of
grounded
outlet box
(C)
(B)
This appliance is for use on 120 volts. The cord has a plug as shown in (A). An adapter as shown in (C) is available
for connecting three-blade grounding type plugs to two-slot receptacles, as shown in (B).
The green grounding plug extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.
To disconnect appliance, turn controls to off, then remove plug from outlet.
EN
W415-1719 / C / 04.07.17
9
installation
The log set insert must be installed in an opening with the minimum cavity sizes shown below:
Do not install the log set into a cavity smaller than that
referenced in the illustration.
4.0 installation
42.5
!
WARNING
• Risk of fi re! The power cord must not be pinched against a sharp edge. Secure cord to avoid tripping or
snagging to reduce the risk of fi re, electric shock, or personal injury. Do nut run cord under carpeting. Do not
cover cord with throw rugs, runners, or similar items. Arrange cord away from traffi c areas and where it will not
be tripped over.
• Risk of fi re! To prevent a possible fi re, do not block air intake or exhaust in any manner. Do not use on soft
surfaces where openings may become blocked.
• Risk of fi re! Do not blow or place insulation against the appliance.
• This electric appliance is tested and listed for use only with the approved optional accessories. Use of optional
accessories not specifi cally tested for this electric appliance could void the warranty and/or result in a safety
hazard.
• If the information in these instructions is not followed exactly, a fi re or explosion may result causing property
damage, personal injury, or death. Do not store or use gasoline or other fl ammable vapors in the vicinity of this
or any other appliance.
• This appliance is heavy. It is highly recommended that two people install this appliance.
• If your appliance is equipped with a heater, ensure the heater vents cannot, in any way, by covered as it may
create a fi re hazard.
• Do not run the power cord horizontally, directly below the appliance.
Follow all national and local electrical codes.
note:
4.1 log set installation
The log set can be installed in any location. It is suggested to install the log set into an existing fireplace or a wood
mantel for aesthetic purposes.
Select a suitable location that is not susceptible to mositure and is away from drapes, furniture and high traffic
areas.
4.1.1 installing log set into existing fireplace
Seal all chimney drafts with non-combustible materials to prevent any chimney debris from falling onto the log
set. Cap the top of the chimney flue to prevent rain from entering.
note:
Plug the log set into an outlet which has a 15Amp, 120V rating. If it is necessary to hard wire the log set, see “hard
wiring installation” section.
• Due to high temperatures, do not use existing fireplace doors which close or seal off the log set. If installed
behind any fireplace door, allow heat to be exhausted. If using existing screens, the screen must provide
adequate airflow in front of the log set.
!
WARNING
16”
(40.6cm)
27 1/2”
(69.8cm)
14”
(35.6cm)
W415-1719 / C / 04.07.17
EN
10
installation
4.1.2 installing log set into mantel
To prevent damaging the base of the mantel, carefully lift the log set into the mantel while avoiding contact
with the front edge of the mantel base.
note:
1. With two people, lift the log set up and insert into the opening. Do not push or slide the bottom of the log set
on the floor base, see Figure 1.
2. Set the log set down and into place, see Figure 2.
Fig. 2
MANTEL
DO NOT SLIDE LOG SET
NE GLISSEZ PAS L'APPAREIL
!
!
MANTEL
STEP 1: LIFT
STEP 2: INSERT
STEP 3:
SET APPLIANCE
MANTEL
DO NOT SLIDE LOG SET
NE GLISSEZ PAS L'APPAREIL
!
!
MANTEL
STEP 1: LIFT
STEP 2: INSERT
STEP 3:
SET APPLIANCE
Fig. 1
EN
W415-1719 / C / 04.07.17
11
installation
4.2 hard wiring installation
HARD WIRING CONNECTION
If it is necessary to hard wire, a qualified electrician must remove the cord connection and wire directly to the
household wiring. The wire and power supply breaker must be rated for 120V and a minimum of 15Amps.
This log set must be electrically connected and grounded in accordance with local codes, if hard wired, in the
absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the current ANSI/
NFPA 70 National Electrical Code in the United States.
There are 3 wires from the fireplace junction; white (neutral), black (power L1) and green (ground) that
connect to 120V power supply (breaker panel), see below.
note:
It is recommended to secure the log set after hard wiring, refer to “securing the log set” section.
note:
!
WARNING
• Turn off the appliance completely and let cool before servicing. Only a qualifi ed service person should service
and repair this electric appliance.
GREEN
BLACK
WHITE
White, Green and
Black wires:
Connect to 120V
power supply.
1. Remove the securing screw from the electrical cover plate, located on the rear of the log set.
2. Add an electrical box connector and feed the supply wires through the 7/8” (22mm) hole.
3. Separate the black, white and green wires that have the wire nuts on them.
4. Remove the wire nuts and secure the black wire (power L1) to the black (power L1) lead of the power supply.
Connect the white wire from the appliance to the white (neutral) wire from the power supply. Connect the
green wire to the ground wire.
5. Resecure the cover plate.
BLACK
WHITE
BLACK
WHITE
GREEN
GREEN
GROUND
BLACK
BLACK
BLACK
WHITE
WHITE
WIRE NUT
WALL
SWITCH
POWER
SUPPLY
MARRET
RED
RED
RED
RED
GREEN
GREEN
THERMOSTAT
(L1)
(N)
(G)
WIRE NUT
(L1)
(N)
(L1)
(N)
Leave enough wire so
that the log set can be
removed from the
enclosure without
disconnecting the power
supply.
note:
W415-1719 / C / 04.07.17
EN
12
installation
4.3 securing the log set
It is recommended to secure the log set, especially if hard wiring the log set.
note:
1. Place the log set in a position which provides optimum flame performance.
2. Secure in place using 2 screws (not supplied), which are suitable for the material that the appliance is being
secured to.
To achieve flame effect, the log set should be set 1” (25mm) away from the rear wall.
note:
EN
W415-1719 / C / 04.07.17
13
finishing
• Power supply service must be completed prior to finishing to avoid reconstruction.
• Heat vents and air openings cannot be covered in any circumstances.
!
WARNING
5.0 finishing
5.1 log placement
Magnetic
Pads
Place the logs shown on the location
dimples on the burner platform.
#1
PIN
PIN
Place log (#1) onto the pin. Ensure the
log is secure onto the pin, as shown.
1 2
Place log (#3) onto the pin. Ensure the
log is secure onto the pin, as shown.
#2
#3
PIN
3 4
Place log (#2) onto the pin. Ensure the
log is secure onto the pin, as shown.
W415-1719 / C / 04.07.17
EN
14
finishing
6.0 operating instructions
Once the log set has been plugged into a grounded electrical outlet or hard wired to a dedicated 120V power
supply, it is ready to operate.
ATTENTION: Ensure the house circuit breakers for the power supply are turned on. When initially
connecting the appliance into a power source, the appliance will perform an LED check. The appliance
will flash on and off for 5 seconds.
The control panel is located on the lower right of the appliance.
6.1 operating control panel
Power
Turns the appliance ON/OFF.
Flame & Ember Light
Control
Heater Control
Timer
Temperature
Control
Controls Flame brightness and the Ember Light.
5 Settings
: Flame & Ember off (FO), Ember on but Flame
off (LL), small Flame & Ember (F1), medium Flame &
Ember (F2), brightest Flame and Ember (F3).
Default setting is (F3).
Turns the Heater and Blower ON/OFF.
4 Settings: Heater & Blower off (HO), Blower on (BL), low
heat (H1), high heat (H2).
Default setting is (HO).
Timer can be programed to run appliance for specific
lengths of time (30mins. minimum to 6hrs maximum).
Default setting is Timer de-select.
Press and hold the Timer button for 5 seconds. This
will change the button to Temperature Control, or vice
versa. There are 7 temperature settings (61
°F, 64°F, 70°F,
75
°F, 81°F, 85°F and OFF).
Default setting is de-select Temperature Control.
F° / C° Switch
Hold 5
seconds
To change temperature format, Fahrenheit or Celsius.
Press and hold the Flame button for 5 seconds.
Default setting is Fahrenheit.
Heater Lock
Hold 5
seconds
Heater button can be locked or unlocked by holding the
Heater button for 5 seconds.
Default setting is heater unlock
Hold 5
seconds
EN
W415-1719 / C / 04.07.17
15
operating instructions
• To avoid danger of suffocation, keep the packaging bag away from babies and children. Do not use in cribs,
bed, carriages or play pens. This bag is not a toy. Knot before throwing away.
!
WARNING
6.2 operating by remote control
When operating the remote control, it must be directed towards the front center of the log set.
note:
A. The power button can be used to turn the log set on/off. Pressing
this button activates the power to the log set. Pressing the power
button again will turn off the log set. The ember and log will fade after
4 seconds after turning off the log set.
B. To adjust the flame brightness and ember log light, press the flame
button . There is one ember log light and three flame brightness
levels to cycle through and then an off setting (LL, F1, F2, F3 and then
F0). F3 is the brightest flame level, LL is the ember log light only.
C. To control the thermostat function press the thermostat button .
There are 7 temperature settings (61°F, 64°F, 70°F, 75°F, 81°F,
85°F and off). The default setting will display Fahrenheit. Press the
thermostat button to cycle through the settings. Once you have
selected the desired temperature the heater will automatically operate
until that temperature is reached. When the room temperature is 2
degrees lower than the temperature setting, the heater will turn on.
D. To activate the heater and blower, press the heater button , the
blower will turn on. Press the heater button again to set desired low
or high heat temperature; press the heater button again to turn off the
heater.
E. The timer controls all operating modes of the log set. To activate the
timer, press the timer button , the icon will illuminate and the time will
appear on the LED display. To choose the desired time, continue to
press the timer button, there are 8 settings (30mins,1h, 2h, 3h, 4h, 5h,
6h and off). The fireplace will turn off at the setting time.
F. To turn off the log set, press the power button once on the remote, or press the power button once on the
control panel on the appliance.
This hand held remote control must remain within 6 meters or 19 feet of the log set to be effective.
note:
6.3 remote battery installation
1. To replace the existing battery, remote the battery
holder.
2. To remove the battery holder, turn remote onto front
side and press the left side lever towards the center
while pulling the battery holder out using the slot
provided.
3. Replace existing battery, type CR 2025, with a
new battery and reinstall the battery holder into the
remote by sliding it into position, as shown.
4. Battery cover is secure onto the remote control
when a "CLICKING" noise is heard.
REMOTE
(REAR SIDE)
BATTERY (CR 2025)
BATTERY COVER
W415-1719 / C / 04.07.17
EN
16
wiring diagram
7.0 wiring diagram
• Turn off the appliance completely and let cool before servicing. Only a qualified service person should service and
repair this electric appliance.
!
WARNING
PLUG /
FICHE
FAN /
SOUFFLERIE
MOTOR /
MOTEUR
AC-N
AC-L
RLY1 RLY2 RLY3 RLY4
NTC
OUT
OUT
IN
#7
#8
#5
#6
#2 #4
#14
#1
#9
#3
#11
#12
#13
#10
#15
CARTE DE CIRCUIT IMPRIMÉ
MAIN PCB BOARD /
L
N
G
WIRE NUT /
CONNECTEUR
DE FILS
WIRE NUT /
CONNECTEUR
DE FILS
WIRE NUT /
CONNECTEUR
DE FILS
HEATER 700W2 /
CHAUFFERETTE 700W2
HEATER 700W1 /
CHAUFFERETTE 700W1
THERMAL CUT-OFF / COUPURE
THERMIQUE
700W1
700W2
MOTOR /
MOTEUR
FAN /
SOUFFLERIE
T-FUSE /
FUSIBLE
FLAME /
FLAMME
DISPLAY CN3 /
AFFICHAGE
TEMPERATURE
SENSOR /
CAPTEUR DE
TEMPÉRATURE
CONTROL PANEL BOARD /
PANNEAU DE CONTRÔLÉ
FLAME LED LIGHT /
LUMIÈRE DEL DE FLAMME
LOG LIGHT /
DEL DES BÛCHES
#1 EMBER BED LIGHT /
#1 LUMIÈRE LIT DE BRAISES
LOG LIGHT /
DEL DES BÛCHES
Page 1 of 1
MATERIAL: CLASS IIIA-2 PERMANENT LEXAN ADHESIVE LABEL, MINIMUM THICKNESS 0.1MM, NON WATER SOLUBLE ADHESIVE CAPABLE OF WITHSTANDING A MAXIMUM
TEMPERATURE OF 175°F (79°C).
SPECIFICATION: BLACK LETTERING ON WHITE BACKGROUND. MINIMUM FONT SIZE TO BE MINIMUM OF 8.5 PT (3.2mm)
MAX OVERALL SIZE: 6" x 4.25"
TITLE: LABEL, WIRING DIAGRAM, NEFI27H-CTC
REVISION:
DWG#: W385-2189
DATE: 02.21.17_H.W.
W385-2189
OUT
EN
W415-1719 / C / 04.07.17
17
replacements
8.0 replacements
!
WARNING
26.1
• Failure to position the parts in accordance with this manual or failure to use only parts specifi cally approved
with this appliance may result in property damage or personal injury.
Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts can
be ordered through your Authorized dealer / distributor.
For warranty replacement parts, a photocopy of the original invoice will be required to honour the
claim.
When ordering replacement parts always give the following information:
• Model & Serial Number of appliance
• Installation date of appliance
• Part number
• Description of part
• Finish
Parts, part numbers, and availability are subject to change without notice.
Parts identifi ed as stocked will be delivered within 2 to 5 business days for most delivery
destinations.
Parts not identifi ed as stocked will be delivered within a 2 to 4 week period, for most cases.
Parts identifi ed as ‘SO’ are special order and can take up to 90 days for delivery
W415-1719 / C / 04.07.17
EN
18
replacements
8.1 overview
Care must be taken when removing and disposing of any broken glass or damaged components. Be sure to
vacuum up any broken glass from isnide the appliance before operation.
note:
1
W135-0609
W135-0604
W135-0603
W135-0607
W135-0606
W135-0608
3
5
6
7
4
8
DescriptionRef. No.
Part Number
1
2
3
4
5
6
7
8
W435-0059-SER
Synchronous Motor
G660-0004-SER
Remote Control Transmitter
Top Left Log
Top Centre Log
Top Right Log
Rear Log
Front Right Log
Front Left Log
W135-0609-SER
W135-0608-SER
W135-0604-SER
W135-0603-SER
W135-0606-SER
W135-0607-SER
Items may not appear exactly as illustrated.
Stocked
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
2
EN
W415-1719 / C / 04.07.17
19
troubleshooting
9.0 troubleshooting
sympton problem test solution
Dim or no fl ame Flame brightness not selected. See “operation” section.
Flame LEDs are burnt out. Inspect the LED and replace, if necessary.
Main PCB board burnt out. Inspect the Main PCB board and replace, if necessary.
Ember bed is not
glowing or dimming.
Brightness not selected. See “operation” section.
Ember LEDs are burnt out. Inspect the ember bed LEDs and replace, if necessary.
Main PCB board burnt out. Inspect the Main PCB board and replace, if necessary.
No warm air coming
out of appliance.
Heater setting not selected. See “operation” section.
Heater has been locked out. See “operation” section.
Room temperature is higher
than appliance setting (if set to
room temperature).
Reset temperature setting.
Appliance has overheated
and safety thermal switch has
tripped.
Unplug power and turn off the circuit breaker. Allow for appliance to
cool for 15 minutes.
Heater is burnt out Inspect the blower and heater and replace, if necessary.
Appliance turns off
and will not turn on.
House circuit breaker has
tripped.
Reset house circuit breaker.
Appliance’s fuse has blown. Replace the fuse.
Appliance has overheated
and safety thermal switch has
tripped.
Unplug power to turn off the circuit breaker, allow appliance to cool
for 15 minutes to reset the thermal switch, then plug in or turn it on.
Appliance will not
come on when
power button/switch
is put into the “on’
position.
Appliance is not plugged into
an electrical outlet.
Check plug and plug it in.
Hard wire connections are not
correct (if applicable).
See “hard wiring installation” section.
Appliance has overheated
and safety thermal switch has
tripped.
Unplug power or turn off the circuit breaker, allow appliance to cool
for 15 minutes, then plug in or turn the breaker on.
Circuit board is burnt out. Inspect the circuit board and replace, if necessary.
Remote control
does not work.
Low/dead batteries. Replace batteries in remote control.
Remote receiver malfunction. Ensure remote receiver is not blocked. Replace control panel.
Heater shuts off
automatically
Room is too warm. The heater has a built-in thermostat so it will shut off automatically
once the pre-set temperature is reached. It will also turn on
automatically if the room temperature drops below the pre-set
temperature.
Flame does not
move.
Motor stalled/malfunction. Cycle on/off. If problem persists, consult dealer.
Power failure. Appliance has returned to
default settings.
Re-program appliance to original settings (not applicable with all
appliances.)
LED fl ashing. Appliance has overheated
and safety thermal switch has
tripped.
Unplug power or turn off the circuit breaker. Allow appliance to cool
for 15 minutes, then plug in or turn the breaker on.
27.5
• Turn off the appliance completely and let cool before servicing. Only a qualifi ed service person should service and
repair this electric appliance.
!
WARNING
W415-1719 / C / 04.07.17
EN
20
warranty
10.0 warranty
2.5
Napoleon warrants its products against manufacturing defects to the original purchaser only. Registering your warranty is
not necessary. Simply provide your proof of purchase along with the model and serial number to make a warranty claim.
Provided that the purchase was made through an authorized Napoleon dealer, your appliance is subject to the following
conditions and limitations:
Warranty coverage begins on the date of original installation.
This factory warranty is non-transferable and may not be extended whatsoever by any of our representatives.
Installation must be done in accordance with the installation instructions included with the product and all local and national
building and fi re codes.
This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse, or
neglect and parts installed from other manufacturers will nullify this warranty.
This limited warranty further does not cover any scratches, dents, corrosion, or discolouring caused by excessive heat,
abrasive and chemical cleaners, nor chipping on porcelain enamel parts, mechanical breakage of PHAZER™ logs.
In the fi rst year only, this warranty extends to the repair or replacement of warranted parts which are defective in material
or workmanship, provided that the product has been operated in accordance with the operation instructions and under
normal conditions.
Napoleon will not be responsible for installation, labour, or any other expenses related to the reinstallation of a warranted
part, and such expenses are not covered by this warranty. Notwithstanding any provisions contained in the Limited
Warranty, Napoleon responsibility under this warranty is defi ned as above, and it shall not in any event extend to any
incidental, consequential, or indirect damages.
This warranty defi nes the obligations and liability of Napoleon with respect to the Napoleon electric appliance and any
other warranties expressed or implied with respect to this product; its components or accessories are excluded.
Napoleon neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the
sale of this product.
Any damages to appliance, brass trim or other component due to water, weather damage, long periods of dampness,
condensation, damaging chemicals, or cleaners will not be the responsibility of Napoleon.
Napoleon reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty
claim.
All parts replaced under the Limited Warranty Policy are subject to a single claim.
All parts replaced under the warranty will be covered for a period of 90 days from the date of their installation.
The manufacturer may require that defective parts or products be returned or that digital pictures be provided to support
the claim. Returned products are to be shipped prepaid to the manufacturer for investigation. If a product is found to be
defective, the manufacturer will repair or replace such defect.
Before shipping your appliance or defective components, your dealer must obtain an authorization number. Any
merchandise shipped without authorization will be refused and returned to sender.
Shipping costs are not covered under this warranty.
Additional service fees may apply if you are seeking warranty service from a dealer.
Napoleon electric appliances are manufactured under the strict Standard of the world recognized
ISO 9001 : 2008 Quality Assurance Certifi cate.
Napoleon products are designed with superior components and materials and assembled by trained craftsmen who take
great pride in their work. Once assembled, the complete appliance is thoroughly inspected by a qualifi ed and authorized
installer, service agency, or supplier before packing to ensure that you, the customer, receive the quality product that you
expect from Napoleon.
Electrical components and wearable parts are covered and Napoleon will provide replacement parts free of charge during
the fi rst year of limited warranty. This covers: fan/heaters, motors, switches, nylon bearing components, remote controls,
and LED lights.*
Light bulbs and fuses are NOT covered by the warranty.
Any labour related to warranty repair is not covered.
* Construction of models vary. Warranty applies only to components included with your specifi c appliance.
Napoleon Electric Appliance Limited Warranty
Conditions and Limitations
All specifi cations and designed are subject to change without prior notice due to on-going product improvements. Napoleon is a registered
trademark of Wolf Steel Ltd.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
NAPOLEON NEFI27H-CTC Le manuel du propriétaire
- Catégorie
- Cheminées
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: NAPOLEON NEFI27H-CTC Owner's manual
Documents connexes
-
NAPOLEON NEFBD50HE-EU Guide d'installation
-
Wolf Steel NEFI24H Le manuel du propriétaire
-
Wolf Steel NEFI24H Le manuel du propriétaire
-
-
-
-
-
