Kichler Lighting 44222BK Manuel utilisateur

Taper
Manuel utilisateur
Date Issued: 11/15/17
IS-44222-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starting and during the installation.
RIGID STEM MOUNT
1) Pass wire through stems[2] and screw stems into couplings[1]
on top of xture body. NOTE: Thread locking compound must
be applied to all stem threads as noted with symbol (3) to pre-
vent accidental rotation of xture during cleaning, relamping,
etc.
2) Pass xture wire through remaining stems and screw stems
together.
3) On each side of xture, pass xture wire through one small
threaded pipe[3]. Screw each small threaded pipe onto top of
stem on each side.
4) On each side of xture, pass xture wires through each hole
in canopy[6]. Lower canopy down towards stems. Pass each
hole in canopy over end of each threaded pipe on top of
stems.
5) On one side of xture, pass xture wire through lockwasher[7].
Thread lockwasher onto end of threaded pipe protruding from
inside canopy. Pass xture wire through hexnut[8]. Thread
hexnut onto end of threaded pipe.
6) On other side of xture, slide lockwasher onto end of threaded
pipe protruding from inside canopy and thread hexnut onto end
of threaded pipe.
7) Find the appropriate threaded holes on mounting strap[12].
Assemble mounting screws[13] into threaded holes.
8) Attach mounting strap to outlet box[14] using mounting strap
screws[15]. Mounting strap can be adjusted to suit position of
xture.
9) Grounding instructions: (See Illus. A or B).
A) On xtures where mounting strap is provided with a hole
and two raised dimples. Wrap ground wire from outlet box
around green ground screw, and thread into hole.
B) On xtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and green
ground screw, and thread into mounting strap.
If xture is provided with ground wire. Connect xture ground
wire to outlet box ground wire with wire connector. (Not pro-
vided.) After following the above steps. Never connect ground
wire to black or white power supply wires.
10) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
11) Push xture to ceiling, carefully passing mounting screws
through holes in canopy. NOTE: Be certain wires do not get
pinched between mounting strap and canopy.
12) Secure xture to ceiling with lock-up nobs[11] and lockwash-
ers[10].
13) Assemble the wood sides[17 &18] by locking the ends with the
tabs into the slots.
14) Secure the assembled wood to light frame[16] using the sup-
plied screws[19] and the supplied hexnuts[20]. Note that the
hexnuts will be on the inside.
15) Insert recommended bulb (not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
LOOP/CHAIN LINK MOUNT
1) Follow steps 1 and 2 from Rigid Stem Mount Instructions.
2) Thread one small threaded pipe[5] into end of each small
loop[4].
3) Pass xture wire through rst loop. Thread one rst loop onto
end of each last stem.
4) On one side of xture, pass xture wire through second loop
and through hole in canopy[6]. Pass threaded pipe at end of
second loop through hole in canopy.
5) Pass xture wire through hole in lockwasher[7] and hexnut[8].
Thread hexnut onto end of threaded pipe.
6) On other side of xture, pass threaded pipe at end of second
loop through hole in canopy.
7) Pass xture wire through lockwasher. Thread lockwasher onto
end of threaded pipe protruding from inside canopy.
8) Pass xture wire through hexnut. Thread hexnut onto end of
threaded pipe.
9) Attach chain link[9] to small loop[4] at end of each stem and to
each loop on canopy.
10) Follow steps 7 - 15 from Rigid Stem Mount Instructions.
OUTLET BOX
13
12
15
14
7
8
2
1
6
4
9
4
11
10
5
5
17
18
19
16
20
3
Date Issued: 11/15/17
IS-44222-CB
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
Nous sommes là pour vous aider 866-558-5706
Heures : du lundi au vendredi, de 9h à 17h (heure de l’Est)
ATTENTION – RISQUE DE DÉCHARGES ÉLECTRIQUES -
Couper le courant au niveau du panneau du disjoncteur du
circuit principal ou de la boîte à fusibles principale avant de
procéder à l’installation.
INSTALLATION SUR TIGE CANNELÉE
1) Acheminerlelduluminaireparlatigeetvisserlatigeen
hautduluminaire[1][2]. REMARQUE:appliquerlefreinlet
surtouslesletsdelatigeindiquésparlesymbole(3)pour
empêcherlarotationaccidentelleduluminairependantlenet-
toyage,remplacementdelampe,etc.
2) Acheminerlelduluminaireparlestigesrestantesetvisser
lestigesensemble.
3) Dechaquecôtéduluminaire,passerunlduluminaireparun
petittuyauleté[3].Vissertouslespetitstubesletéssurle
dessusdelatigedechaquecôté.
4) Dechaquecôtéduluminaire,passerleslsduluminaireà
traverschaquetroudanslecache[6].Abaisserlecachesur
lestiges.Passerchaquetroudanslecachesurl’extrémitéde
chaquetubeletésituéau-dessusdestiges.
5) Suruncôtéduluminaire,passerunlduluminaireparletrou
dansunerondelledeblocage[7].Visserlarondelledeblocage
surl’extrémitédutubeletésortantdel’intérieurducache.
Passerlelduluminaireparl’écrouhexagonal[8].Visser
l’écrouhexagonalsurl’extrémitédutubeleté.
6) Dechaquecôtéduluminaire,Visserlarondelledeblocagesur
l’extrémitédutubeletésortantdel’intérieurducacheetvisser
l’écrouhexagonalsurl’extrémitédutubeleté.
7) Trouverlestrousletésappropriéssurlabarrettedemon-
tage[12].Vissezlesvisdemontage[13]danslestrousletés.
8) Vissezlabarredemontagesurlaboîtedejonction[14]àl’aide
desvisdelasangledemontage[15].Labarrettedemontage
peutetreajustéepourconveniràlapositiondel’applique.
9) Connecterlesls(connecteursnonfournis).Sereporterau
tableauci-dessouspourfairelesconnexions.
10) Pousserleluminaireversleplafondenpassantsoigneuse-
mentlesvisdemontageparlestrousdanslecache.NOTE:
Becertainwiresdonotgetpinchedbetweenmountingstrap
andcanopy.
11) Fixerleluminairesécuritairementauplafondavecdesrodelles
deblocage[11]etboutonsdexation[10].
12)Assemblezlescôtésenbois[17 & 18]enverrouillantlesex-
trémitésavecleslanguettesdanslesfentes.
13)Fixezleboisassemblésurlecadre[16]àl’aidedesvis
fournies[19]etdeshexagonesfournis[20].Notezqueles
hexagonesserontàl’intérieur.
14) Installerlaoulesampoulesrecommandées(nonfournies).
Connecter le fil noir ou
rouge de la boite
Connecter le fil blanc de la boîte
A Noir A Blanc
*Au cordon parallèle (rond et lisse)
*Au cordon parallele (à angles droits el strié)
Au bransparent, doré, marron, ou
noir sans fil distinctif
Au transparent, doré, marron, ou
noir avec un til distinctif
Fil isolé (sauf fil vert) avec
conducteur en cuivre
Fil isolé (sauf fil vert) avec
conducteur en argent
*Remarque: Avec emploi d’un fil paralléle
(SPT I et SPT II). Le fil neutre est á angles
droits ou strié et l’autre fil doit étre rond ou
lisse (Voir le schéma).
Fil Neutre
MONTAGE DES LIENS EN BOUCLE/MAILLON
1) Suivrelesétapes1et2desinstructionsMontagedelatige.
2) Visserlesbouclessurl’extrémitédechaquetubeleté[3][16].
3) Ajouterunmaillonàchaqueboucleetpuisuneautreboucleà
chaquemaillon.
4) Surundescôtésduluminaire,passerlelduluminaireparla
deuxièmebouclepuisparletroudanslecache[6].Passerle
tubeletéàl’extrémitédeladeuxièmeboucleparletrousitué
danslecache.
5) Alimentezleldexationàtraversletroudanslarondelle[7]
deverrouillageetl’écrouhexagonal[8].Enlerl’écrouhexago-
nalàl’extrémitédutuyauleté.
6) Surl’autrecôtéduluminaire,passerletubeletéàl’extrémité
deladeuxièmeboucleparletrousituédanslecache.
7) Fairepasserleldexationdansletroudelarondelled’arrêt.
Enlerlarondelled’arrêtsurl’extrémitédutuyauletéfaisant
saillieàl’intérieurdelacanopée.
8) Fairepasserleldexationdansletrouduhexnut.Enlez
hexnutsurl’extrémitédutuyauleté.
9) Fixezunmaillondechaîne[17]àunepetiteboucl[4]eàlan
dechaquetigeetàchaqueboucleducouvercle.
10) Suivrelesétapes7à14desinstructionsMontagedelatige.
OUTLET BOX
13
12
15
14
7
8
2
1
6
4
9
4
11
10
5
5
17
18
19
16
20
3
  • Page 1 1
  • Page 2 2

Kichler Lighting 44222BK Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues