GE GSS22QGMCC Le manuel du propriétaire

Safety Information
Adapter Plugs  . . . . . . . . . . . . . . . . . . .4
Electricity . . . . . . . . . . . . . . . . . . . . . . .4
Extension Cords  . . . . . . . . . . . . . . . . .3
Proper Disposal  . . . . . . . . . . . . . . . . .3
Safety Precautions  . . . . . . . . . . . . .2, 3
Operating Instructions
Automatic Icemaker  . . . . . . . . . . . . .9
Controls   . . . . . . . . . . . . . . . . . . . . . . .5
Crispers and Pans . . . . . . . . . . . . . .8–9
Ice and Water Dispenser . . . . . . . . .10
Shelves, Bins and Racks  . . . . . . . .6–8
Water Filter Cartridge  . . . . . . . . . . . .6
Care and Cleaning
Cleaning  . . . . . . . . . . . . . . . . . . .11, 12
Lightbulbs . . . . . . . . . . . . . . . . . . . . .13
Installation Instructions
Preparing to Install 
the Refrigerator  . . . . . . . . . . . . .14, 15
Water Line Installation  . . . . . . .16–20
Troubleshooting Tips
Before You Call For Service  . . .22–25
Normal Operating Sounds  . . . . . . .22
Consumer Support
Consumer Support . . . . . .Back Cover
Performance Data Sheet  . . . . . . . . .27
Product Registration . . . . . . . . .29, 30
State of California Water 
Treatment Device Certificate . . . . .28
Warranty (Canadian)  . . . . . . . . . . .25
Warranty (U.S.)  . . . . . . . . . . . . . . . .26
www.GEAppliances.com
Refrigerators
Side by Side
197D3351P002     49-60131    03-01 JR
Write your model and serial numbers here:
Model # _____________________
Serial # _____________________
Find these numbers on a label inside
the refrigerator compartment at the top
on the right side behind the controls.
Réfrigérateurs
Côte à  côte
Refrigeradores
Lado a lado
Models 20, 22 and 25
Manuel d’utilisation 
et d’installation
Owner’s Manual and
Installation Instructions
Manual del propietario
y instalación
La section française commence à la page 31
La sección en español empieza en la página 59

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet. Skin

may stick to these extremely cold surfaces.

■

■Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating element

that releases the cubes. Do not place fingers or

hands on the automatic icemaking mechanism

while the refrigerator is plugged in.

■

■Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■Setting the freezer control to the

0

(off) position

does not remove power to the light circuit.

■

■Do not refreeze frozen foods which have

thawed completely.

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous…even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator

or Freezer:

■Take off the doors.

■Leave the shelves in place so that children may

not easily climb inside.

CFC Disposal

Your old refrigerator may have a cooling system

that used CFCs (chlorofluorocarbons). CFCs are

believed to harm stratospheric ozone.

If you are throwing away your old refrigerator, make

sure the CFC refrigerant is removed for proper

disposal by a qualified servicer. If you intentionally

release this CFC refrigerant you can be subject to

fines and imprisonment under provisions of

environmental legislation.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend

against the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

3

www.GEAppliances.com

4

Consumer Support Troubleshooting Tips Installation Instructions Safety Instructions

Operating Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with

a 3-prong (grounding) plug which mates with a

standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

If the outlet is a standard 2-prong outlet, it is your

personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall

outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull straight

out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

USE OF ADAPTER PLUGS

(Adapter plugs not permitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an adapter plug.

However, if you must use an adapter, where local

codes permit, a

temporary connection

may be made

to a properly grounded 2-prong wall outlet by use

of a UL-listed adapter available at most local

hardware stores.

The larger slot in the adapter must be aligned with

the larger slot in the wall outlet to provide proper

polarity in the connection of the power cord.

When disconnecting the power cord from the

adapter, always hold the adapter in place with one

hand while pulling the power cord plug with the

other hand. If this is not done, the adapter ground

terminal is very likely to break with repeated use.

If the adapter ground terminal breaks,

DO NOT USE

the refrigerator until a proper ground has been

established.

Attaching the adapter ground terminal to a wall outlet

cover screw does not ground the appliance unless the

cover screw is metal, and not insulated, and the wall

outlet is grounded through the house wiring. You should

have the circuit checked by a qualified electrician to make

sure the outlet is properly grounded.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

5

About the controls on the refrigerator.

www.GEAppliances.com

9 IS COLDEST

0 IS OFF

FREEZER FRESH FOOD

5

8

9

4

3

2

1

0

6

7

5

8

9

4

3

2

1

6

7

Initially, set the fresh food control at 5 and the freezer control at 5 and

allow 12 hours for the temperature to stabilize.

Several adjustments may be required. Adjust the controls one

increment at a time, and allow 12 hours after each adjustment for the

refrigerator to reach the temperature you set.

Setting the freezer control to 0 stops cooling in both the fresh food

and freezer compartments but does not shut off electrical power to

the refrigerator.

Control settings will vary based on personal preferences, usage, and

operating conditions and may require more than one adjustment.

9 IS COLDEST

0 IS OFF

FREEZER FRESH FOOD

5

8

9

4

3

2

1

0

6

7

5

8

9

4

3

2

1

6

7

6

Consumer Support Troubleshooting Tips Installation Instructions Safety Instructions

Operating Instructions

About the water filter cartridge.

About the shelves and bins.

Bins on the Fresh Food Compartment Door

Adjustable bins can easily be carried from

refrigerator to work area.

To remove:

Lift the front of the bin up, then

pull out.

To replace or relocate:

Engage the bin in the

molded supports of the door, and push in.

Bin will lock in place.

The snugger

helps prevent tipping, spilling

or sliding of small items stored on the door

shelf. Place a finger on either side of the

divider near the rear and move it back

and forth to fit your needs.

Water Filter Cartridge

The water filter cartridge is located in the

back upper right corner of the refrigerator

compartment.

When to Replace the Filter on

Models With a Replacement

Indicator Light

There is a replacement indicator light for

the water filter cartridge on the dispenser.

This light will turn orange to tell you that

you need to replace the filter soon.

The filter cartridge should be replaced

when the replacement indicator light turns

red or if the flow of water to the dispenser

or icemaker decreases.

When to Replace the Filter on

Models Without a Replacement

Indicator Light

The filter cartridge should be replaced

every

six months

or earlier if the flow of

water to the water dispenser or icemaker

decreases.

Installing the Filter Cartridge

If you are replacing the cartridge, first

remove the old one by slowly turning it

to the left.

Do not

pull down on the

cartridge. A small amount of water may

drip down.

On models without a replacement

indicator light, apply the month and

year sticker to the new cartridge to

remind you to replace the filter in

six

months.

Fill the replacement cartridge with water

from the tap to allow for better flow

from the dispenser immediately after

installation.

Lining up the arrow on the cartridge

and the cartridge holder, place the

top of the new cartridge up inside

the holder.

Do not

push it up into

the holder.

Slowly turn it to the right until the filter

cartridge stops.

DO NOT OVERTIGHTEN.

As you turn the cartridge, it will

automatically raise itself into position.

Cartridge will rotate about 1/2 turn.

Run water from the dispenser for 3

minutes (about one and a half gallons)

to clear the system and prevent

sputtering.

Press and hold the

RESET WATER FILTER

pad (on some models) on the dispenser

for 3 seconds.

NOTE:

A newly-installed water filter

cartridge may

cause water to spurt

from

the dispenser.

Filter Bypass Plug

You must use the filter bypass plug

when a replacement filter cartridge is not

available. The dispenser and the icemaker

will not operate without the filter or filter

bypass plug.

Replacement Filters:

To order additional filter cartridges in

the United States, visit our Website,

www.GEAppliances.com, or call

GE Parts and Accessories, 800-626-2002.

GWF

Suggested Retail $34.95

Customers in Canada should consult the

yellow pages for the nearest Camco Service

Center.

Place the top of the cartridge up

inside the cartridge holder and

slowly turn it to the right.

Filter Bypass Plug

Cartridge Holder

On some models

Not all features are on all models.

Snugger

(on some models)

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Rearranging the Shelves

To Remove

To Replace

Deep Door Shelves

Detachable shelf extenders deepen and

enclose fixed door shelves, providing

more storage room and greater storage

flexibility.

To remove:

Lift the shelf extender straight up

then pull out.

To replace:

Engage the shelf extender in the

molded supports on the door and push in.

It will lock in place.

Quick Space Shelf

(on some models)

This shelf splits in half and slides under

itself for storage of tall items on the shelf

below.

Refrigerator Shelves:

Lift up and out

Tilt up

Insert

top hook

Lower to

lock in

place

To Remove

Freezer Shelves:

Slide-Out Spillproof Shelf

(on some models)

The slide-out spillproof shelf allows you to

reach items stored behind others. The

special edges are designed to help prevent

spills from dripping to lower shelves.

Make sure you push the shelves all the way back

in before you close the door.

Spillproof Shelves

(on some models)

Spillproof shelves have special edges

to help prevent spills from dripping to

lower shelves.

www.GEAppliances.com

To Remove

Freezer Baskets:

Remove the basket by pulling it forward,

lifting up the front, and sliding it past the

stop

location.

7

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

8

About the crispers and pans.

Not all features are on all models.

About the additional features.

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the

bottom of the drawers should be wiped dry.

Adjustable Humidity Crispers

Slide the control all the way to the

High

or setting to provide high

humidity recommended for most

vegetables.

Slide the control all the way to the

Low

or

setting to provide lower humidity levels

recommended for most fruits.

Convertible Meat Pan

The convertible meat pan has its own cold

air duct to allow a stream of cold air from

the freezer compartment to flow around

the pan.

The variable temperature control

regulates

the air flow from the freezer compartment.

Set control lever

up

to convert the pan

to normal refrigerator temperature and

provide extra vegetable storage space. Cold

air duct is turned off. Variable settings

between these extremes can be selected.

Set control lever

down

to the coldest setting

to store fresh meats. If lever is left in meat

position for a long period of time, some

frost may form on the inside of the pan.

Normal

Coldest

Trivet

Trivet and Divider

(on some models)

ShelfSaver

™

Rack

Use this rack to store beverage cans for

easy access.

It can also hold a 9″x 13″baking dish.

The trivet is designed to keep your fruits

and vegetables off the floor of the drawer

and away from any moisture that might

form. The divider will keep the larger fruits

and vegetables from falling or rolling onto

the more delicate ones. By lifting straight

up on the divider, you can detach it from

the trivet and adjust it from side to side,

then push down and into position.

Divider

Automatic Icemaker

(on some models)

The icemaker will produce seven cubes

per cycle—approximately 100–130 cubes

in a 24-hour period, depending on freezer

compartment temperature, room

temperature, number of door openings

and other use conditions.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch in the

O (off)

position.

When the refrigerator has been connected

to the water supply, set the power switch to

the

l (on)

position.

The icemaker will fill with water when it

cools to 15°F. A newly-installed refrigerator

may take 12 to 24 hours to begin making

ice cubes.

Throw away the first few batches of ice to

allow the water line to clear.

Be sure nothing interferes with the sweep of

the feeler arm.

It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale and shrink.

If ice cubes get stuck in the icemaker,the

green power light will blink. To correct this,

set the power switch to

O (off)

and remove

the cubes. Set the power switch to

l (on)

to

restart the icemaker. After the icemaker has

been turned on again, there will be a delay

of about 45 minutes before the icemaker

resumes operation.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

About crisper removal.

www.GEAppliances.com

Not all features are on all models.

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

About the automatic icemaker.

A newly-installed refrigerator may take 12–24 hours to begin making ice.

Crisper Removal

Crispers can easily be removed by tilting up

slightly and pulling past

stop

location.

If the door prevents you from taking out

the crispers, the refrigerator will need to

be rolled forward until the door opens

enough to slide the crispers out. In some

cases, when you roll the refrigerator out,

you will need to move the refrigerator to

the left as you roll it out.

When replacing the crispers, make

sure you slide them through the

crisper guides.

There is an upper freezer shelf

above the icemaker that can be

used for storage.

Crisper

Guides

Ice Storage Drawer

Icemaker Accessory Kit

To access ice,

pull the drawer out.

To remove the drawer,

pull it straight out

and lift it past the

stop

location.

If your refrigerator did not come already

equipped with an automatic icemaker,

an icemaker accessory kit is available at

extra cost.

Check the back of the refrigerator for

the specific icemaker kit needed for

your model.

9

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

10

Consumer Support Troubleshooting Tips Installation Instructions Safety Instructions

Operating Instructions

About the ice and water dispenser.

On some models

Ice Storage Drawer

on Dispenser Models

To remove:

Set the icemaker power switch to the

O (off)

position. Pull the drawer straight out and

then lift past the

stop

position.

To replace:

When replacing the drawer, make sure to

push it firmly into place. If it does not go all

the way back, remove it and rotate the drive

mechanism 1/4 turn. Then push the

drawer back again.

Rotate

Drive

Mechanism

Important Facts About Your Dispenser

■Do not add ice from trays or bags to

the storage bin. It may not crush or

dispense well.

■Avoid overfilling glass with ice and use of

narrow glasses. Backed-up ice can jam the

chute or cause the door in the chute to

freeze shut. If ice is blocking the chute,

poke it through with a wooden spoon.

■Beverages and foods should not be

quick-chilled in the ice storage bin.

Cans, bottles or food packages in the

storage bin may cause the icemaker

or auger to jam.

■To keep dispensed ice from missing

the glass, put the glass close to, but not

touching, the dispenser opening.

■Some crushed ice may be dispensed even

though you selected

CUBED ICE.

This

happens occasionally when a few cubes

have been left in the crusher.

■After crushed ice is dispensed, some

water may drip from the chute.

■Sometimes a small mound of snow will

form on the door in the ice chute. This

condition is normal and usually occurs

when you have dispensed crushed ice

repeatedly. The snow will eventually

evaporate.

To Use the Dispenser

Select

CUBED ICE , CRUSHED ICE

or

WATER .

Press the glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining. To

reduce water spotting, the shelf and its grille

should be cleaned regularly.

If no water is dispensed when the refrigerator is

first installed, there may be air in the water line

system. Press the dispenser arm for at least two

minutes to remove trapped air from the water line

and to fill the water system. To flush out impurities

in the water line, throw away the first six glassfuls

of water.

CAUTION: Never put fingers or any other

objects into the ice crusher discharge opening.

Locking the Dispenser

(on some models)

Press the

LOCK

CONTROL

pad for 3

seconds to lock the

dispenser and control

panel. To unlock, press

and hold the pad again

for 3 seconds.

Dispenser Light

This pad turns the

night

light

in the dispenser on

and off. The light also

comes on when the

dispenser cradle is

pressed. If this light

burns out, it should be

replaced with a 6 watt

maximum, 12 volt DC

bulb.

Spill Shelf

Condenser

There is no need for routine condenser

cleaning in normal home operating

environments. However, in environments

that may be particularly dusty or greasy, the

condenser should be cleaned periodically

for efficient refrigerator operation.

Cleaning the condenser:

The condenser is located inside the back

of the refrigerator. To access it, first unplug

the refrigerator. Then remove the access

cover. The condenser is on the right side.

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Care and cleaning of the refrigerator.

www.GEAppliances.com

Cleaning the Outside

The dispenser drip area,

(on some models)

beneath the grille, should be wiped dry. Water

left in this area may leave deposits. Remove

the deposits by adding undiluted vinegar to

the well. Soak until the deposits disappear

or become loose enough to rinse away.

The dispenser cradle

(on some models).

Before cleaning, lock the dispenser by

pressing and holding the

LOCK CONTROL

pad for 3 seconds. Clean with warm water

and baking soda solution—about a

tablespoon (15 ml) of baking soda to a

quart (1 l) of water. Rinse thoroughly

and wipe dry.

The door handles and trim.

Clean with a

cloth dampened with soapy water. Dry

with a soft cloth.

Keep the outside clean.

Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.

Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish

cloth or wet towel. These may leave a residue

that can erode the paint. Do not use scouring

pads, powdered cleaners, bleach or cleaners

containing bleach because these products can

scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors,

leave an open box of

baking soda in the fresh food and freezer

compartments.

Unplug the refrigerator before cleaning.

If this

is not practical, wring excess moisture out of

sponge or cloth when cleaning around

switches, lights or controls.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda

to a quart (1 l) of water. This both cleans

and neutralizes odors. Rinse and wipe dry.

After cleaning the door gaskets, apply a thin

layer of petroleum jelly to the door gaskets

at the hinge side. This helps keep the

gaskets from sticking and bending out

of shape.

Drain opening in freezer compartment.

During yearly cleaning, remove bottom

freezer basket and flush a solution of baking

soda—1 teaspoon (5 ml) and 2 cups (500

ml) of hot (not boiling) water—through the

drain line with the help of a meat baster.

This will help eliminate odor and reduce

the likelihood of a clogged drain line. If

drain becomes clogged, use a meat baster

and baking soda solution to force the clog

through the drain line.

Avoid cleaning cold glass shelves with hot water

because the extreme temperature difference may

cause them to break. Handle glass shelves

carefully. Bumping tempered glass can cause it to

shatter.

Do not wash any plastic refrigerator parts in the

dishwasher.

11

Dispenser drip area.

For long vacations or absences, remove

food and unplug the refrigerator. Clean the

interior with a baking soda solution of one

tablespoon (15 ml) of baking soda to one

quart (1 l) of water. Leave the doors open.

Set the icemaker power switch to the

O (off)

position and shut off the water supply to the

refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system (on some models) to prevent

serious property damage due to flooding.

12

Consumer Support Troubleshooting Tips Installation Instructions Safety Instructions

Operating Instructions

Care and cleaning of the refrigerator.

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

Pull the refrigerator straight out and return

it to position by pushing it straight in.

Moving the refrigerator in a side direction

may result in damage to the floor covering

or refrigerator.

When pushing the refrigerator back, make sure

you don’t roll over the power cord or icemaker

supply line (on some models).

Preparing for Vacation

Preparing to Move

Secure all loose items such as grille, shelves and drawers by taping them securely

in place to prevent damage.

Be sure the refrigerator stays in an upright position during moving.

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Replacing the lightbulbs.

www.GEAppliances.com

Turning the control to the 0 (off) position does not remove power to the light circuit.

Fresh Food Compartment—Upper Light

Unplug the refrigerator.

The bulb is located behind the controls.

Replace with an appliance bulb of the

same or lower wattage.

Plug the refrigerator back in.

Fresh Food Compartment—Lower Light

(on some models)

This light is located above the top drawer.

Unplug the refrigerator.

Grasp the lip at the bottom of the light

shield and pull it up and forward.

After replacing with an appliance

bulb of the same or lower wattage,

replace the shield.

Plug the refrigerator back in.

Freezer Compartment

Unplug the refrigerator.

Remove the shelf just below light shield.

(The shelf will be easier to remove if it is

emptied first.)

Lift up on the light shield to remove.

After replacing with an appliance

bulb of the same or lower wattage,

reinstall the shield by hanging it

from the three tabs.

Reinstall the shelf and plug the

refrigerator back in.

13

Dispenser

Unplug the refrigerator.

The bulb is located on the dispenser

under the control panel.

Remove the lightbulb by turning

it counterclockwise.

Replace the bulb with a bulb of the

same size and wattage.

Plug the refrigerator back in.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT

–

Save these

instructions for local inspector’s use.

•

IMPORTANT

–

Observe all

governing codes and ordinances.

•

Note to Installer

–

Be sure to leave these

instructions with the Consumer.

• Note to Consumer

–

Keep these instructions

for future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Refrigerator Installation

15 minutes

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

• Do not install the refrigerator where the temperature

will go below 60°F (16°C) because it will not run often

enough to maintain proper temperatures.

• Install it on a floor strong enough to support it fully

loaded.

REFRIGERATOR LOCATION

Questions? Call 800-GE-CARES (800-432-2737)

or Visit our Website at:

www.GEAppliances.com

Questions? In Canada, call 1-800-361-3400

or Visit our Website at:

www.geappliances.ca

Installation

Refrigerator

Instructions

Models 20, 22, 25

Allow the following clearances for ease of installation,

proper air circulation and plumbing and electrical

connections.

• Sides 1/8″ (4 mm)

• Top 1″ (25 mm)

• Back 1″ (25 mm)

A door clearance of 3/4″(19 mm) is needed for a 90º

door opening which provides better access to the food

storage area.

CLEARANCES

The rollers have 3 purposes:

■ Rollers adjust so the door closes easily when opened

about halfway.

■ Rollers adjust so the refrigerator is firmly positioned on

the floor and does not wobble.

■ Rollers allow you to move the refrigerator away from

the wall for cleaning.

To adjust the rollers, remove the base grille by pulling it

out at the bottom.

Turn the roller adjusting screws clockwise to raise the

refrigerator, counterclockwise to lower it. Use an

adjustable wrench (3/8″hex head bolt) or pliers.

To replace base grille, line up the clips on back of grille

between the bar and the bottom of the cabinet. Push

forward until grille snaps into place.

ROLLERS

If the refrigerator has an icemaker, it will have to be

connected to a cold water line. A GE water supply kit

(containing tubing, shutoff valve, fittings and

instructions) is available at extra cost from your dealer,

by visiting our Website at www.GEAppliances.com

(in Canada, at www.geappliances.ca) or from Parts

and Accessories, 800-626-2002.

WATER SUPPLY TO THE ICEMAKER

(on some models)

14

To remove the base

grille, open the doors

and then pull the

grille straight out.

5/16″Socket

Wrench

Raise

DOOR ALIGNMENT

After leveling, make sure that doors are even at the top.

To make the doors even, adjust the refrigerator door.

Using a 5/16″socket wrench, turn the door adjusting

screw to the right to raise the door, to the left to lower

it. (A nylon plug, embedded in the threads of the pin,

prevents the pin from turning unless a wrench is used.)

After one or two turns of the wrench, open and close

the fresh food door and check the alignment at the top

of the doors.

Installation Instructions

15

Installation Instructions

16

INSTALLING THE WATER LINE

Recommended copper water supply kits are WX8X2,

WX8X3 or WX8X4, depending on the amount of

tubing you need. Approved plastic water supply lines

are GE SmartConnect™ Refrigerator Tubing

(WX08X10002, WX08X10006, WX08X10015 and

WX08X10025).

When connecting your refrigerator to a GE Reverse

Osmosis Water System, the only approved installation

is with a GE RVKit. For other reverse osmosis water

systems, follow the manufacturer’s recommendations.

If the water supply to the refrigerator is from a Reverse

Osmosis Water Filtration System AND the refrigerator

also has a water filter, use the refrigerator’s filter bypass

plug. Using the refrigerator’s water filtration cartridge

in conjunction with the RO filter can result in hollow

ice cubes and slower water flow from the water

dispenser.

This water line installation is not warranted by the

refrigerator or icemaker manufacturer. Follow these

instructions carefully to minimize the risk of expensive

water damage.

Water hammer (water banging in the pipes) in house

plumbing can cause damage to refrigerator parts and

lead to water leakage or flooding. Call a qualified

plumber to correct water hammer before installing

the water supply line to the refrigerator.

To prevent burns and product damage, do not hook

up the water line to the hot water line.

If you use your refrigerator before connecting the

water line, make sure the icemaker power switch is in

the

O (off)

position.

Do not install the icemaker tubing in areas where

temperatures fall below freezing.

When using any electrical device (such as a power

drill) during installation, be sure the device is double

insulated or grounded in a manner to prevent the

hazard of electric shock, or is battery powered.

All installations must be in accordance with local

plumbing code requirements.

BEFORE YOU BEGIN

• Copper or GE SmartConnect™ Refrigerator Tubing

kit, 1/4″ outer diameter to connect the refrigerator to

the water supply. If using copper, be sure both ends of

the tubing are cut square.

To determine how much tubing you need: measure

the distance from the water valve on the back of the

refrigerator to the water supply pipe. Then add 8′

(2.4 m). Be sure there is sufficient extra tubing (about

8′ [2.4 m] coiled into 3 turns of about 10″ [25 cm]

diameter) to allow the refrigerator to move out from

the wall after installation.

GE SmartConnect™ Refrigerator Tubing Kits are

available in the following lengths:

2′ (.6 m) – WX08X10002

6′ (1.8 m) – WX08X10006

15′ (4.6 m) – WX08X10015

25′ (7.6 m) – WX08X10025

Be sure that the kit you select allows at least 8′ (2.4 m)

as described above.

NOTE: The only GE approved plastic tubing is that

supplied in GE SmartConnect™ Refrigerator Tubing

kits. Do not use any other plastic water supply line

because the line is under pressure at all times. Certain

types of plastic will crack or rupture with age and cause

water damage to your home.

WHAT YOU WILL NEED

Installation Instructions

17

SHUT OFF THE MAIN WATER

SUPPLY

Turn on the nearest faucet long enough to clear the

line of water.

Install the shutoff valve on the nearest frequently used

drinking water line.

1

Choose a location for the valve that is easily

accessible. It is best to connect into the side of a

vertical water pipe. When it is necessary to connect

into a horizontal water pipe, make the connection

to the top or side, rather than at the bottom,

to avoid drawing off any sediment from the

water pipe.

CHOOSE THE VALVE LOCATION

2

Drill a 1/4″ hole in the water pipe (even

if using a self-piercing valve) using a sharp bit.

Remove any burrs resulting from drilling the hole in

the pipe. Take care not to allow water to drain into

the drill. Failure to drill a 1/4″ hole may result in

reduced ice production or smaller cubes.

DRILL THE HOLE FOR THE VALVE

3

•A GE water supply kit (containing tubing, shutoff

valve and fittings listed below) is available at extra

cost from your dealer or from Parts and Accessories,

800-626-2002.

•A cold water supply. The water pressure must be

between 20 and 120 p.s.i. (1.4–8.2 bar) on models

without a water filter and between 40 and 120 p.s.i.

(2.8–8.2 bar) on models with a water filter.

•Power drill.

•1/2″or adjustable wrench.

•Straight and Phillips blade screwdriver.

•Two 1/4″ outer diameter compression nuts and

2 ferrules (sleeves)—to connect the copper tubing

to the shutoff valve and the refrigerator

water valve.

OR

•If you are using a GE SmartConnect™ Refrigerator

Tubing kit, the necessary fittings are preassembled to

the tubing.

•If your existing copper water line has a flared fitting

at the end, you will need an adapter (available at

plumbing supply stores) to connect the water line to

the refrigerator OR you can cut off the flared fitting

with a tube cutter and then use a compression fitting.

Do not cut formed end from GE SmartConnect™

Refrigerator tubing.

•Shutoff valve to connect to the cold water line.

The shutoff valve should have a water inlet with a

minimum inside diameter of 5/32″ at the point of

connection to the COLD WATER LINE. Saddle-type

shutoff valves are included in many water supply kits.

Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

WHAT YOU WILL NEED (CONT.)

Installation Instructions

18

Place the compression nut and ferrule (sleeve) for

copper tubing onto the end of the tubing and

connect it to the shutoff valve.

Make sure the tubing is fully inserted into the valve.

Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect™

Refrigerator Tubing kit, insert the molded end

of the tubing into the shutoff valve and tighten

compression nut until it is hand tight, then tighten

one additional turn with a wrench. Overtightening

may cause leaks.

CONNECT THE TUBING TO THE

VALVE

7

Turn the main water supply on and flush out the

tubing until the water is clear.

Shut the water off at the water valve after about

one quart (1 liter) of water has been flushed

through the tubing.

FLUSH OUT THE TUBING

8

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

Saddle-Type

Shutoff Valve

Compression Nut

SmartConnect™

Tubing

Packing Nut

Outlet Valve

Ferrule (sleeve)

Fasten the shutoff valve to the cold water pipe with

the pipe clamp.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

FASTEN THE SHUTOFF VALVE

4

Tighten the clamp screws until the sealing washer

begins to swell.

NOTE: Do not overtighten or you may crush the

tubing.

TIGHTEN THE PIPE CLAMP

5

Vertical Cold

Water Pipe

Saddle-Type

Shutoff Valve

Washer

Inlet End

Pipe Clamp

Clamp Screw

Route the tubing between the cold water line and

the refrigerator.

Route the tubing through a hole drilled in the wall

or floor (behind the refrigerator or adjacent base

cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing

(about 8′ [2.4 m] coiled into 3 turns of about 10″

[25 cm] diameter) to allow the refrigerator to move

out from the wall after installation

.

ROUTE THE TUBING

6

Pipe Clamp

INSTALLING THE WATER LINE (cont.)

Installation Instructions

Tighten any connections that leak.

TURN THE WATER ON AT THE

SHUTOFF VALVE

10

19

Place the compression nut and ferrule (sleeve)

onto the end of the tubing as shown. On a GE

SmartConnect Refrigerator Tubing kit, the nuts

are already assembled to the tubing.

On models using the refrigeration connection at

the water valve, remove the plastic flexible cap.

NOTES:

• Before making the connection to the refrigerator,

be sure the refrigerator power cord is not plugged

into the wall outlet.

• If your refrigerator does not have a water filter, we

recommend installing one if your water supply

has sand or particles that could clog the screen of

the refrigerator’s water valve. Install it in the water

line near the refrigerator. If using a GE

SmartConnect™ Refrigerator Tubing kit, you

will need an additional tube (WX08X10002)

to connect the filter. Do not cut plastic tube

to install filter.

CONNECT THE TUBING TO THE

REFRIGERATOR

9

CONNECT THE TUBING TO THE

REFRIGERATOR

(CONT.)

9

Some models have the refrigerator connection at

the end of tubing located outside the compressor

compartment access cover. On other models, the

compressor compartment access cover must be

removed in order to access the refrigerator

connection at the water valve.

Reattach the access cover.

Insert the end of the tubing into the refrigerator

connection as far as possible. While holding the

tubing, tighten the fitting.

For plastic tubing from a GE SmartConnect

Refrigerator Tubing kit, insert the molded end of

the tubing into the refrigerator connection and

tighten the compression nut until it is hand tight,

then tighten one additional turn with a wrench.

Overtightening may cause leaks.

Fasten the tubing into the clamp provided as

shown to keep it in position. You may need to pry

open the clamp.

One of the illustrations below will look like the

connection on your refrigerator.

1/4″

Compression

Nut

Tubing

Clamp

1/4″

Tubing

Refrigerator

Connection

SmartConnect™

Tubing

Ferrule

(sleeve)

Tubing

Clamp

Refrigerator

Connection

SmartConnect™

Tubing

1/4″

Compression

Nut

Ferrule

(sleeve)

1/4″

Tubing

20

Arrange the coil of tubing so that it does not vibrate

against the back of the refrigerator or against the

wall. Push the refrigerator back to the wall.

PLUG IN THE REFRIGERATOR

11

START THE ICEMAKER

Set the icemaker power switch to the

I (on)

position.

The icemaker will not begin to operate until it

reaches its operating temperature of 15°F (-9°C)

or below. It will then begin operation automatically

if the icemaker power switch is in the

I (on)

position.

NOTE: In lower water pressure conditions, the

water valve may turn on up to 3 times to deliver

enough water to the icemaker.

Installation Instructions

INSTALLING THE WATER LINE (cont.)

La page charge ...

GE GSS22QGMCC Le manuel du propriétaire

GE GSS22QGMCC Le manuel du propriétaire

dans d''autres langues

Documents connexes