Toro 14AQ81RP544, 14AK81RK544 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur

Ce manuel convient également à

1
Register your product at www.Toro.com
launaM srotarepO
772C0848A
02/06
GT2200 & GT2300 Garden Tractors
Model No. 14AQ81RP544
Model No. 14AK81RK544
2
TABLE OF CONTENTS
FINDING MODEL NUMBER
This Operator’s Manual is an important part of your new garden tractor. It will help you assemble, prepare and
maintain the unit for best performance. Please read and understand what it says.
Before you start assembling your new equipment, please locate the model plate on the equipment
and copy the information from it in the space provided below. A sample model plate is also illustrated
below. You can locate the model plate by looking at the underside of the tractor‘s seat. This information
will be necessary to use the manufacturer’s web site and/or help from a Toro Service Dealer.
CUSTOMER SUPPORT
Please do NOT return the unit to the retailer without first contacting Customer Support.
If you have difficulty assembling this product or have any questions regarding the controls, operation or
maintenance of this unit, you can seek help from the experts. Choose from the options below:
Content Page
Important Safe Operation Practices 3
Safety Labels 6
Slope Gauge 7
Tractor Set-up 8
Know Your Garden Tractor 10
Operating Your Garden Tractor 13
Making Adjustments 17
Maintaining Your Garden Tractor 20
Lubrication 21
Service 22
Off-season Storage 25
Maintenance Chart 26
Troubleshooting 27
Specifications 28
Warranty Information 29
Content Page
Copy the model number here:
Copy the serial number here:
MODEL NUMBER SERIAL NUMBER DOM
THE TORO COMPANY
8111 LYNDALE AVE. SOUTH
BLOOMINGTON, MINNESOTA 55420-1196
TOLL FREE PHONE NUMBER: 1-888-384-9942 USA
TOLL FREE PHONE NUMBER: 1-888-848-4073 Canada
6ISIT WWWTOROCOMFORMANYUSEFULSUGGESTIONS#LICKON#USTOMER#AREINTHE(OMEOWNERSSECTION
OFTHE4ORO3OLUTIONS#ENTERANDHELPISIMMEDIATELYAVAILABLE
)FYOUHAVEQUESTIONSCONCERNINGYOURTRACTORPLEASECALLUSAT53
OR#ANADA
3
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES
WARNING: This symbol points out important safety instructions which, if not followed, could endanger
the personal safety and/or property of yourself and others. Read and follow all instructions in this manual
before attempting to operate this machine. Failure to comply with these instructions may result in personal
injury. When you see this symbol—heed its warning.
DANGER: This machine was built to be operated according to the rules for safe operation in this man-
ual. As with any type of power equipment, carelessness or error on the part of the operator can result in
serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to
observe the following safety instructions could result in serious injury or death.
GENERAL OPERATION
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe
place for future and regular reference and for
ordering replacement parts.
2. Be familiar with all controls and their proper
operation. Know how to stop the machine and
disengage them quickly.
3. Never allow children under 14 years old to operate
this machine. Children 14 years old and over
should read and understand the operation
instructions and safety rules in this manual and
should be trained and supervised by a parent.
4. Never allow adults to operate this machine without
proper instruction.
5. To help avoid blade contact or a thrown object
injury, keep bystanders, helpers, children and pets
at least 75 feet from the machine while it is in
operation. Stop machine if anyone enters the area.
6. Thoroughly inspect the area where the equipment
is to be used. Remove all stones, sticks, wire,
bones, toys, and other foreign objects which could
be picked up and thrown by the blade(s). Thrown
objects can cause serious personal injury.
7. Plan your mowing pattern to avoid discharge of
material toward roads, sidewalks, bystanders and
the like. Also, avoid discharging material against a
wall or obstruction which may cause discharged
material to ricochet back toward the operator.
8. Always wear safety glasses or safety goggles
during operation and while performing an
adjustment or repair to protect your eyes. Thrown
objects which ricochet can cause serious injury to
the eyes.
9. Wear sturdy, rough-soled work shoes and close-
fitting slacks and shirts. Loose fitting clothes and
jewelry can be caught in movable parts. Never
operate this machine in bare feet or sandals.
10. Be aware of the mower and attachment discharge
direction and do not point it at anyone. Do not
operate the mower without the discharge cover or
entire grass catcher in its proper place.
11. Do not put hands or feet near rotating parts or
under the cutting deck. Contact with the blade(s)
can amputate hands and feet.
12. A missing or damaged discharge cover can cause
blade contact or thrown object injuries.
13. Stop the blade(s) when crossing gravel drives,
walks, or roads and while not cutting grass.
14. Watch for traffic when operating near or crossing
roadways. This machine is not intended for use on
any public roadway.
15. Do not operate the machine while under the
influence of alcohol or drugs.
16. Mow only in daylight or good artificial light.
17. Never carry passengers.
18. Disengage blade(s) before shifting into reverse.
Back up slowly. Always look down and behind
before and while backing to avoid a back-over
accident.
19. Slow down before turning. Operate the machine
smoothly. Avoid erratic operation and excessive
speed.
20. Disengage blade(s), set parking brake, stop engine
and wait until the blade(s) come to a complete stop
before removing grass catcher, emptying grass,
unclogging chute, removing any grass or debris, or
making any adjustments.
21. Never leave a running machine unattended. Always
turn off blade(s), place transmission in neutral, set
parking brake, stop engine and remove key before
dismounting.
22. Use extra care when loading or unloading the
machine into a trailer or truck. This unit should not
be driven up or down ramp(s), because the unit
could tip over, causing serious personal injury. The
unit must be pushed manually on ramp(s) to load or
unload properly.
23. Muffler and engine become hot and can cause a
burn. Do not touch.
24. Check overhead clearances carefully before driving
under low hanging tree branches, wires, door
openings etc., where the operator may be struck or
pulled from the unit, which could result in serious
injury.
4
25. Disengage all attachment clutches, depress the
brake pedal completely and shift into neutral before
attempting to start engine.
26. Your machine is designed to cut normal residential
grass of a height no more than 10”. Do not attempt
to mow through unusually tall, dry grass (e.g.,
pasture) or piles of dry leaves. Dry grass or leaves
may contact the engine exhaust and/or build up on
the mower deck presenting a potential fire hazard.
27. Use only accessories and attachments approved
for this machine by the machine manufacturer.
Read, understand and follow all instructions
provided with the approved accessory or
attachment.
28. Data indicates that operators, age 60 years and
above, are involved in a large percentage of riding
mower-related injuries. These operators should
evaluate their ability to operate the riding mower
safely enough to protect themselves and others
from serious injury.
29. If situations occur which are not covered in this
manual, use care and good judgment. Contact your
authorized dealer for assistance.
SLOPE OPERATION
Slopes are a major factor related to loss of control and
tip-over accidents which can result in severe injury or
death. All slopes require extra caution. If you cannot
back up the slope or if you feel uneasy on it, do not mow
it.
For your safety, use the slope gauge included as part of
this manual to measure slopes before operating this
unit on a sloped or hilly area. If the slope is greater than
15 degrees as shown on the slope gauge, do not
operate this unit on that area or serious injury could
result.
DO:
1. Mow up and down slopes, not across. Exercise
extreme caution when changing direction on
slopes.
2. Watch for holes, ruts, bumps, rocks, or other
hidden objects. Uneven terrain could overturn the
machine. Tall grass can hide obstacles.
3. Use slow speed. Choose a low enough speed
setting so that you will not have to stop or shift while
on the slope. Tires may lose traction on slopes
even though the brakes are functioning properly.
Always keep machine in gear when going down
slopes to take advantage of engine braking action.
4. Follow the manufacturer’s recommendations for
wheel weights or counterweights to improve
stability.
5. Use extra care with grass catchers or other
attachments. These can change the stability of the
machine.
6. Keep all movement on the slopes slow and gradual.
Do not make sudden changes in speed or direction.
Rapid engagement or braking could cause the front
of the machine to lift and rapidly flip over backwards
which could cause serious injury.
7. Avoid starting or stopping on a slope. If tires lose
traction, disengage the blade(s) and proceed
slowly straight down the slope.
DO NOT:
1. Do not turn on slopes unless necessary; then, turn
slowly and gradually downhill, if possible.
2. Do not mow near drop-offs, ditches or
embankments. The mower could suddenly turn
over if a wheel is over the edge of a cliff, ditch, or if
an edge caves in.
3. Do not try to stabilize the machine by putting your
foot on the ground.
4. Do not use a grass catcher on steep slopes.
5. Do not mow on wet grass. Reduced traction could
cause sliding.
6. Do not shift to neutral and coast downhill. Over-
speeding may cause the operator to lose control of
the machine resulting in serious injury or death.
7. Do not tow heavy pull behind attachments (e.g.
loaded dump cart, lawn roller, etc.) on slopes
greater than 5 degrees. When going down hill, the
extra weight tends to push the tractor and may
cause you to loose control. (e.g. tractor may speed
up, braking and steering ability are reduced,
attachment may jack-knife and cause tractor to
overturn).
CHILDREN
1. Tragic accidents can occur if the operator is not
alert to the presence of children. Children are often
attracted to the machine and the mowing activity.
They do not understand the dangers. Never
assume that children will remain where you last
saw them.
a. Keep children out of the mowing area and in
watchful care of a responsible adult other
than the operator.
b. Be alert and turn machine off if a child enters
the area.
c. Before and while backing, look behind and
down for small children.
d. Never carry children, even with the blade(s)
shut off. They may fall off and be seriously
injured or interfere with safe machine
operation.
e. Use extreme care when approaching blind
corners, doorways, shrubs, trees or other
objects that may block your vision of a child
who may run into the machine.
f. To avoid back-over accidents, always
disengage the cutting blade(s) before shifting
5
into reverse. The “Reverse Caution Mode”
should not be used when children or others
are around.
g. Keep children away from hot or running
engines. They can suffer burns from a hot
muffler.
h. Remove key when machine is unattended to
prevent unauthorized operation.
2. Never allow children under 14 years old to operate
the machine. Children 14 years old and over should
read and understand the operation instructions and
safety rules in this manual and should be trained
and supervised by a parent.
TOWING
1. Tow only with a machine that has a hitch designed
for towing. Do not attach towed equipment except at
the hitch point.
2. Follow the manufacturers recommendation for
weight limits for towed equipment and towing on
slopes.
3. Never allow children or others in or on towed
equipment.
4. On slopes, the weight of the towed equipment may
cause loss of traction and loss of control.
5. Travel slowly and allow extra distance to stop.
6. Do not shift to neutral and coast downhill.
SERVICE
SAFE HANDLING OF GASOLINE:
1. To avoid personal injury or property damage
use extreme care in handling gasoline. Gasoline is
extremely flammable and the vapors are explosive.
Serious personal injury can occur when gasoline is
spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.
a. Use only an approved gasoline container.
b. Never fill containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always
place containers on the ground away from
your vehicle before filling.
c. When practical, remove gas-powered
equipment from the truck or trailer and refuel
it on the ground. If this is not possible, then
refuel such equipment on a trailer with a
portable container, rather than from a
gasoline dispenser nozzle.
d. Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times until
fueling is complete. Do not use a nozzle lock-
open device.
e. Extinguish all cigarettes, cigars, pipes and
other sources of ignition.
f. Never fuel machine indoors.
g. Never remove gas cap or add fuel while the
engine is hot or running. Allow engine to cool
at least two minutes before refueling.
h. Never over fill fuel tank. Fill tank to no more
than ½ inch below bottom of filler neck to
allow space for fuel expansion.
i. Replace gasoline cap and tighten securely.
j. If gasoline is spilled, wipe it off the engine and
equipment. Move unit to another area. Wait 5
minutes before starting the engine.
k. To reduce fire hazards, keep machine free of
grass, leaves, or other debris build-up. Clean
up oil or fuel spillage and remove any fuel
soaked debris.
l. Never store the machine or fuel container
inside where there is an open flame, spark or
pilot light as on a water heater, space heater,
furnace, clothes dryer or other gas
appliances.
m. Allow a machine to cool at least 5 minutes
before storing.
GENERAL SERVICE:
1. Never run an engine indoors or in a poorly
ventilated area. Engine exhaust contains carbon
monoxide, an odorless, and deadly gas.
2. Before cleaning, repairing, or inspecting, make
certain the blade(s) and all moving parts have
stopped. Disconnect the spark plug wire and ground
against the engine to prevent unintended starting.
3. Periodically check to make sure the blades come to
complete stop within approximately (5) five seconds
after operating the blade disengagement control. If
the blades do not stop within the this time frame,
your unit should be serviced professionally by an
authorized dealer.
4. Check brake operation frequently as it is subjected
to wear during normal operation. Adjust and service
as required.
5. Check the blade(s) and engine mounting bolts at
frequent intervals for proper tightness. Also, visually
inspect blade(s) for damage (e.g., excessive wear,
bent, cracked).
Replace the blade(s) with the original equipment
manufacturer’s (O.E.M.) blade(s) only, listed in this
manual. “Use of parts which do not meet the original
equipment specifications may lead to improper
performance and compromise safety!”
6. Mower blades are sharp. Wrap the blade or wear
gloves, and use extra caution when servicing them.
7. Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
8. Never tamper with the safety interlock system or
other safety devices. Check their proper operation
regularly.
9. After striking a foreign object, stop the engine,
disconnect the spark plug wire(s) and ground
against the engine. Thoroughly inspect the machine
for any damage. Repair the damage before starting
and operating.
6
10. Never attempt to make adjustments or repairs to
the machine while the engine is running.
11. Grass catcher components and the discharge
cover are subject to wear and damage which could
expose moving parts or allow objects to be thrown.
For safety protection, frequently check components
and replace immediately with original equipment
manufacturer’s (O.E.M.) parts only, listed in this
manual. “Use of parts which do not meet the origi-
nal equipment specifications may lead to improper
performance and compromise safety!”
12. Do not change the engine governor settings or
over-speed the engine. The governor controls the
maximum safe operating speed of the engine.
13. Maintain or replace safety and instruction labels, as
necessary.
14. Observe proper disposal laws and regulations for
gas, oil, etc. to protect the environment.
WARNING: YOUR RESPONSIBILITY Restrict the use of this power machine to persons who read,
understand and follow the warnings and instructions in this manual and on the machine.
SECTION 2: SAFETY LABELS
Safety Labels found on your unit
MAX 20
%
S30544
S3032356
7
SECTION 3: SLOPE GAUGE
15°
SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE
A POWER POLE
A CORNER OF A BUILDING
OR A FENCE POST
F
O
L
D
O
N
D
O
T
T
E
D
L
I
N
E
,
R
E
P
RE
S
E
N
T
I
N
G
A
1
5
°
S
L
O
P
E
USE THIS PAGE AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY.
Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A
riding mower could overturn and cause serious injury. If operating a walk-behind mower on such a slope, it is
extremely difficult to maintain your footing and you could slip, resulting in serious injury.
Operate RIDING mowers up and down slopes, never across the face of slopes.
WARNING
8
SECTION 4: TRACTOR SET-UP
NOTE: Reference to RIGHT or LEFT side of the
tractor in this manual is observed from operator’s
position.
ATTACHING THE BATTERY CABLES
NOTE:
The battery cables may or may not be
attached on your unit. If the cables are not attached,
please follow the instructions below.
NOTE: The positive battery terminal is marked Pos.
(+). The negative battery terminal is marked Neg. (–).
The positive cable (heavy red wire) is secured to
the positive battery terminal (+) with a hex bolt and
hex nut at the factory. Make certain that the rubber
boot covers the terminal to help protect it from
corrosion.
Remove the hex bolt and wing nut from the
negative cable.
Remove the black plastic cover, if present, from the
negative battery terminal and attach the negative
cable (heavy black wire) to the negative battery
terminal (–) with the bolt and wing nut.
Make certain the battery retainer rod is in position
over the battery, securing it in place. See Figure 1.
Figure 1
NOTE: If the battery is put into service after the date
shown on top of battery, charge the battery as
instructed on page 23 of this manual prior to operating
the tractor.
ATTACHING THE STEERING WHEEL
In the event your tractor was crated with the steering
wheel and the seat removed for shipping reasons, use
the following instructions to properly assemble the
parts.
WARNING: Do NOT operate the tractor
without first attaching both the steering
wheel AND the seat. Doing so could result
in serious injury to the operator.
NOTE: There are two different styles of steering
wheel cap. See Figure 2. Styles vary by model.
Using your hands, place the tractor’s front tires in
position for straight-ahead travel.
Remove the steering wheel cap from the center of
the steering wheel. Be careful not to lose the hex
screw and cupped washer found beneath it.
Place the steering wheel (in position for straight-
ahead travel) directly onto the steering shaft found
in the center of the tractor’s dash.
Place the cupped washer (cupped side DOWN)
over the steering shaft.
Thread the hex screw into the steering shaft and
tighten securely.
Reinsert the steering wheel cap in the center of the
steering wheel. Refer to Figure 2
.
Figure 2
ATTACHING THE SEAT
Refer to Figures 3 and 4 to identify your tractor’s seat
style and follow applicable instructions.
NOTE: For shipping reasons, seats are either
fastened to the tractor seat’s pivot bracket with a plastic
tie, or mounted backward to the pivot bracket. In either
case, free the seat from its shipping position and
remove the two hex screws (or knobs, on models so
equipped) from the bottom of seat before proceeding
with applicable instructions below
.
Shoulder Bolt
Wing
Nu
t
Rubber
Bo
ot
Positive
Terminal
Negative
Terminal
Battery
Battery
Retainer Rod
Steering
Hex Bolt
Steering
Shaft
& Washer
Wheel Cap
9
Quick Adjustment Seat
NOTE: If your seat was shipped mounted backwards
on the seat pivot bracket, pull out the tab found on the
seat stop and hold it open while sliding the seat off the
seat pivot bracket. See Figure 3.
Line up the plastic seat spacers with the slots in
seat pivot bracket.
Slide seat in until front seat spacer engages the
seat stop. See Figure 3.
Figure 3
WARNING: Before operating this machine,
make sure the seat is engaged in the seat
stop, stand behind the machine and pull back
on seat until fully engaged into stop
.
Knob Adjustment Seat
Position the shoulder screws (found on the base of
the seat) inside the slot openings in the seat pivot
bracket. See Figure 4.
Slide the seat slightly rearward in the seat pivot
bracket, lining up the rear slots in the pivot bracket
with the remaining two holes in the seat’s base.
Select desired position for the seat, and secure with
the two knobs removed earlier. See Figure 4.
Figure 4
GAS AND OIL FILL-UP
The gasoline tank is located under the hood and has a
capacity of either two or three gallons. Do not overfill.
WARNING: Use extreme care when
handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
Never fuel machine indoors or while the
engine is hot or running. Extinguish
cigarettes, cigars, pipes, and other sources of
ignition.
Service the engine with gasoline and oil as
instructed in the separate engine manual packed
with your tractor. Read instructions carefully.
IMPORTANT: Your tractor is shipped with oil;
however, you MUST check the oil level before
operating. Be careful not to overfill. Overfilling with oil
may cause the engine to smoke. This will result in poor
engine performance and could cause permanent
engine damage.
WARNING: The mowing deck is capable of
throwing objects. Failure to operate the riding
mower without the discharge cover in the
proper operating position could result in
serious personal injury and/or property
damage.
TIRE PRESSURE
WARNING: Maximum tire pressure under
any circumstances is 30 p.s.i. Equal tire
pressure should be maintained at all times.
The tires on your unit may be over-inflated for shipping
purposes. Reduce the tire pressure before operating
the tractor. Recommended operating tire pressure is
approximately 10 p.s.i for the rear tires & 14 p.s.i. for
the front tires. Check the sidewall of tire for maximum
p.s.i.
Seat Stop
Tab
Pivot Bracket
QUICK ADJUSTMENT
KNOB ADJUSTMENT
Knobs
Shoulder
Opening
Pivot Bracket
in Slot
Screws
10
SECTION 5: KNOW YOUR GARDEN TRACTOR
NOTE: Any reference in this manual to the RIGHT or LEFT side of the tractor is observed from operator’s position
A Systems Indicator Monitor/Hour Meter G Throttle Control
B PTO (Blade Engage) Knob H Ignition Switch Module
C Choke Control I Brake Pedal
D Parking Brake Lever J Drive Pedal
E Seat Adjustment Lever K Cruise Control Lever
F Cup Holder L Deck Lift Lever
SLO
W
A
G
L
J
I
D
B
C
H
NOTE: Steering
K
F
E
11
THROTTLE CONTROL LEVER
The throttle control lever is located on the right side of
the tractor’s dash panel. This lever controls the speed of
the engine and, on some models, when pushed all the
way forward, the choke control also. When set in a
given position, the throttle will maintain a uniform engine
speed. See Figure 5.
Figure 5
IMPORTANT: When operating the tractor with the
cutting deck engaged, be certain that the throttle lever is
always in the FAST (rabbit) position.
CHOKE CONTROL
The choke control can be found
on the left side of the dash panel
and is activated by pulling the
knob outward. Activating the
choke control closes the choke
plate on the carburetor and aids
in starting the engine. Refer to
STARTING THE ENGINE in the
OPERATION section of this
manual for detailed starting
instructions.
BRAKE PEDAL
The brake pedal is located on the
right front side of the tractor
above the drive pedal along the
running board. The brake pedal
can be used for sudden stops or
setting the parking brake.
NOTE: The brake pedal must
be fully depressed to activate the
safety interlock switch when
starting the tractor
.
IGNITION SWITCH
WARNING: Never leave a running machine
unattended. Always disengage PTO, move
shift lever into neutral position, set parking
brake, stop engine and remove key to prevent
unintended starting.
To start the engine, insert the key into the ignition switch
and turn clockwise to the START position. Release the
key into the NORMAL MOWING MODE position once
the engine has fired.
To stop the engine, turn the ignition key
counterclockwise to the STOP position. See Figure 6.
Figure 6
IMPORTANT: Prior to operating the tractor, refer to
both Safety Interlock Switches, page 13 and Starting The Engine,
page 14 of this manual for detailed instructions regarding
the Ignition Switch Module and operating the tractor in
REVERSE CAUTION MODE.
DRIVE PEDAL
The drive pedal is located below
the brake pedal on the right front
side of the tractor along the
running board. Depress the upper
portion of the drive pedal forward
to cause the tractor to travel
forward. Depress the lower
portion of the drive pedal with the
ball of your right foot (NOT your
heel) to cause the tractor to travel
in reverse. Ground speed is also
controlled with the drive pedal.
The further forward or rearward
that the pedal is pivoted, the
faster the tractor will travel. The
pedal will return to its original
position when it’s not depressed.
IMPORTANT: Always set the
parking brake when leaving the tractor unattended.
Slow
Choke
Fast
Position
Position
Position
Slow
Fast
Position
Position
Start
Position
Normal
Driving
Mode
Stop
Position
12
SYSTEMS INDICATOR MONITOR
LCD
Located in the center of the tractor’s console, the
systems indicator monitor records, and displays on its
LCD, hours of tractor operation whenever the ignition
key is rotated out of the STOP position.
The indicator Monitor will also remind the operator of
maintenacne intervals for changing the engine oil. The
LCD will alternately flash the recorded hours, “CHG”
and “OIL” for five minutes, after every 50 hours of
recorded operation elapse. The maintenance interval
lasts for two hours (from 50-52, 100-102, 150-152,
etc.). The LCD will also flash as described above for
five minutes every time the tractor’s engine has been
started during this maintenance interval. Before the
interval expires, change the crankcase oil level as
instructed in this Operator’s Manual.
Figure 7
If the Brake light or PTO light illuminates when
attempting to start the unit, proceed as follows:
Brake Engage the parking brake.
PTO Move the PTO lever into the disengaged
(Blade Stop) position.
It is normal for the Oil light and the Battery light to
illuminate while the engine is cranking, but if either
illuminates while the engine is running, proceed as
follows:
Oil Stop the tractor immediately and check the
crankcase oil level as instructed in the
Engine Owner’s Manual included with
your unit. Add oil as required.
Battery If this light illuminate’s while the engine is
running, it indicates that the battery is in
need of a charge OR that the engine’s
charging system is not generating
sufficient amperage. Refer to the
MAINTENANCE section of this manual
for the proper battery charging procedure
or have the engine’s charging system
checked by a authorized dealer.
On units so equipped, the ammeter measures the
electrical output of the engine’s charging system. Under
normal operating conditions, with the engine at full
throttle, the ammeter’s needle should measure a
positive charge.
The hour meter, on units so equipped, operates
whenever the engine is running and records the actual
hours of tractor operation.
ELECTRIC PTO (POWER
TAKE-OFF) KNOB
To engage the power to the
cutting deck or other (separately
available) attachments on
models so equipped with an
electric PTO, pull outward on the
PTO knob. Push the PTO knob
inward to disengage the power to the cutting deck.
NOTE: The PTO knob must be in the disengaged
(Blade Stop) position when starting the engine.
PTO (POWER TAKE-OFF) LEVER
On models equipped with a manual PTO, the PTO lever
is located on the left side of the dashboard next to the
steering wheel. Move the PTO lever forward to engage
the power to the cutting deck or other (separately
available) attachments; move the PTO lever rearward
to disengage the power.
NOTE: The PTO lever must be in the disengaged
(Blade Stop) position when starting the engine.
SEAT ADJUSTMENT LEVER
To adjust the seat forward or backward on units
equipped with a quick-adjust seat, slide the seat
adjustment lever to the left and reposition the seat to
the desired position. Once a comfortable position is
found, release the seat adjustment lever to lock the
seat in place. Refer to SEAT ADJUSTMENTS in the
MAKING ADJUSTMENTS section of this manual for
more detailed instructions.
DECK LIFT LEVER
Found on your tractor’s right fender, the deck lift lever is
used to change the height of the cutting deck. To use,
move the lever to the left, then place in the notch best
suited for your application.
CUP HOLDER
The tractor’s cup holder is located on the fender to the
left of the seat, just to the rear of the parking brake
lever.
{Ó°äÊ
13
CRUISE CONTROL
BUTTON
The cruise control button is
located on the tractor dash panel
to the left of the ignition switch.
Push the cruise control button
while traveling forward at a
desired speed. While holding the
button in, release pressure from
the drive pedal. This will engage
the cruise control and allow the
tractor to remain at that speed without applying
pressure to the drive pedal. Depress the brake pedal or
the drive pedal to deactivate cruise control. Refer to
OPERATION SECTION of this manual for detailed
instructions regarding the cruise control feature.
NOTE: Cruise control can NOT be engaged at the
tractor’s fastest ground speed. If the operator should
attempt to do so, the tractor will automatically
decelerate to the fastest optimal mowing ground speed.
PARKING BRAKE
BUTTON
To set the parking brake, fully
depress the brake pedal and
push the parking brake button in.
Hold the button in while taking
your foot off the brake pedal. Both
the parking button and the brake
pedal will then stay depressed.
To release the parking brake,
depress the brake pedal slightly.
The parking brake button will then return to its original
position.
NOTE: The parking brake must be set if the operator
leaves the seat with the engine running or the engine
will automatically shut off.
IMPORTANT: Always set the parking brake when
leaving the tractor unattended.
SECTION 6: OPERATING YOUR GARDEN TRACTOR
WARNING: Read, understand, and follow
all instructions and warnings on the machine
and in this manual before operating.
SAFETY INTERLOCK SWITCHES
This tractor is equipped with a safety interlock system
for the protection of the operator. If the interlock system
should ever malfunction, do not operate the tractor.
Contact an authorized service dealer.
The safety interlock system prevents the engine
from cranking or starting unless the parking brake is
engaged, and the PTO (Blade Engage) knob (or
lever) is in the disengaged (OFF) position. To check
for proper operation, move the PTO (Blade Engage)
knob into the engaged (ON) position and release
the parking brake. Attempts to start the tractor’s
engine should fail.
The engine will automatically shut off if the operator
leaves the seat before engaging the parking brake.
To check for proper operation, start the tractor’s
engine, release the parking brake and momentarily
raise yourself from the seat. The engine should
stall.
Models with Manual PTO (Blade Engage)
The engine will automatically shut off if the operator
leaves the tractor’s seat with the PTO (Blade
Engage) lever in the engaged (ON) position,
regardless of whether the parking brake is
engaged. To check for proper operation, start the
tractor’s engine, move the PTO (Blade Engage)
lever in the engaged (ON) position and momentarily
raise yourself from the seat. The engine should
stall.
With the ignition key in the NORMAL MOWING
position, the engine will automatically shut off if the
PTO (Blade Engage) lever is moved into the
engaged (ON) position with the the drive pedal in
position for Reverse travel. To check for proper
operation, start the tractor’s engine with the ignition
key in the NORMAL MOWING position, move the
PTO (Blade Engage) knob in the engaged (ON)
position and place the the drive pedal in position for
Reverse travel. The cutting deck should disengage.
P
AVOID SERIOUS INJURY OR DEATH
• GO UP AND DOWN SLOPES, NOT ACROSS.
• AVOID SUDDEN TURNS.
DO NOT OPERATE THE UNIT WHERE IT COULD SLIP OR TIP.
IF MACHINE STOPS GOING UPHILL, STOP BLADE(S) AND BACK
DOWNHILL SLOWLY.
DO NOT MOW WHEN CHILDREN OR OTHERS ARE AROUND.
NEVER CARRY CHILDREN, EVEN WITH BLADES OFF.
LOOK DOWN AND BEHIND BEFORE AND WHILE BACKING.
KEEP SAFETY DEVICES (GUARDS, SHIELDS, AND SWITCHES) IN
PLACE AND WORKING.
REMOVE OBJECTS THAT COULD BE THROWN BY THE BLADE(S).
KNOW LOCATION AND FUNCTION OF ALL CONTROLS.
BE SURE BLADE(S) AND ENGINE ARE STOPPED BEFORE PLAC-
ING HANDS OR FEET NEAR BLADE(S).
BEFORE LEAVING OPERATOR’S POSITION, DISENGAGE
BLADE(S), PLACE THE SHIFT LEVER IN NEUTRAL, ENGAGE
BRAKE LOCK, SHUT ENGINE OFF AND REMOVE KEY.
READ OPERATOR’S MANUAL
WARNING
14
Models with Electric PTO (Blade Engage)
The electric PTO (Blade Engage) clutch will
automatically shut off if the operator leaves the
tractor’s seat with the PTO (Blade Engage) knob in
the engaged (ON) position, regardless of whether
the parking brake is engaged. To check for proper
operation, start the tractor’s engine, move the PTO
(Blade Engage) lever in the engaged (ON) position
and momentarily raise yourself from the seat. The
engine should stall.
With the ignition key in the NORMAL MOWING
position, the electric PTO (Blade Engage) clutch will
automatically shut off if the PTO (Blade Engage)
knob is moved into the engaged (ON) position with
the drive pedal in position for Reverse travel. To
check for proper operation, start the tractor’s engine
with the ignition key in the NORMAL MOWING
position, move the PTO (Blade Engage) knob in the
engaged (ON) position and place the the drive
pedal in position for Reverse travel. The cutting
deck should disengage.
WARNING: Do not operate the tractor if the
interlock system is malfunctioning. This
system was designed for your safety and
protection.
REVERSE CAUTION MODE
The REVERSE CAUTION MODE position of the key
switch module allows the tractor to be operated in
reverse with the blades (PTO) engaged.
IMPORTANT: Mowing in reverse is not recommended.
WARNING: Use extreme caution while
operating the tractor in the REVERSE
CAUTION MODE. Always look down and
behind before and while backing. Do not
operate the tractor when children or others
are around. Stop the tractor immediately if
someone enters the area.
To use the REVERSE CAUTION MODE:
IMPORTANT:
The operator MUST be seated in the
tractor seat.
1. Start the engine as previously instructed in this
Operator’s Manual.
2. Turn the key from the NORMAL MOWING (Green)
position to the REVERSE CAUTION MODE
(Yellow) position of the key switch module. See
Figure 8.
3. Depress the REVERSE PUSH BUTTON (Orange,
Triangular Button) at the top, right corner of the key
switch module. The red indicator light at the top, left
corner of the key switch module will be ON while
activated. See Figure 8.
4. Once activated (indicator light ON), the tractor can
be driven in reverse with the cutting blades (PTO)
engaged.
Figure 8
5. Always look down and behind before and while
backing to make sure no children are around
6. After resuming forward motion, return the key to the
NORMAL MOWING position.
IMPORTANT:
The REVERSE CAUTION MODE will
remain activated until:
a. The key is placed in either the NORMAL
MOWING position or STOP position.
b. The operator leaves the seat (Models with
Electric PTO ONLY).
c. The operator engages the parking brake by
fully depressing the brake pedal and holding
it down while gently pushing the parking
brake button inward (Models with Manual
PTO ONLY).
SETTING THE CUTTING HEIGHT
Select the height position of the cutting deck by placing
the deck lift lever in any of the six different cutting height
notches on the right side of the fender. Then adjust the
deck wheels so that they are between ¼-inch and ½-
inch above the ground when the tractor is on a smooth,
flat surface such as a driveway.
WARNING: Keep hands and feet away
from the discharge opening of the cutting
deck.
NOTE: The deck wheels are an anti-scalp feature of
the deck and are not designed to support the weight of
the cutting deck.
Refer to the ADJUSTMENTS section of this manual for
more detailed instructions regarding various deck
adjustments.
STARTING THE ENGINE
WARNING:
Do not operate the tractor if
the interlock system is malfunctioning. This
system was designed for your safety and
protection.
NOTE: Refer to the TRACTOR SET-UP section of this
manual for Gasoline and Oil fill-up instructions.
Stop
Position
Start
Position
Indicator
Light
Reverse
Push
Button
Reverse
Caution Mode
Position
15
Insert the tractor key into the ignition switch.
Place the PTO knob (or lever) in the disengaged
(Blade Stop) position.
Engage the tractor’s parking brake.
Move the throttle control lever into the FAST
(rabbit), or CHOKE position, if so equipped.
Pull out the choke control knob, if so equipped. A
warm engine may not require choking.
Turn the ignition key clockwise to the START
position. After the engine starts, release the key. It
will return to the NORMAL MOWING position.
IMPORTANT: Do NOT hold the key in the START
position for longer than ten seconds at a time. Doing so
may cause damage to your engine’s electric starter.
NOTE: If starting problems are encountered, refer to
the TROUBLESHOOTING section of this manual.
After the engine starts, deactivate the choke
control.
NOTE: Do NOT leave the choke control on while
operating the tractor. Doing so will result in a "rich" fuel
mixture and cause the engine to run poorly.
STOPPING THE ENGINE
WARNING: If you strike a foreign object,
stop the engine, disconnect the spark plug
wire(s) and ground against the engine.
Thoroughly inspect the machine for any
damage. Repair the damage before restarting
and operating.
If the blades are engaged, place the PTO/Blade
Engage knob (or lever) in the disengaged (Blade
Stop) position.
Move the throttle control into the SLOW position
and allow the engine to “idle down” for ten seconds,
then turn the ignition key counterclockwise to the
OFF position.
Remove the key from the ignition switch to prevent
unintended starting.
ENGAGING THE PARKING BRAKE
To engage the parking brake:
Fully depress the brake pedal and hold it there while
gently pushing the parking brake button inward.
Hold the parking brake button in while removing
your foot from the brake pedal.
Once engaged, the parking brake button and the
brake pedal will lock in the “down” position.
To disengage the parking brake:
Slightly depress the brake pedal.
NOTE: The parking brake must be engaged if the
operator leaves the seat with the engine running or the
engine will automatically shut off.
DRIVING THE TRACTOR
WARNING: Avoid sudden starts, ex-
cessive speed and sudden stops.
WARNING: Do not leave the seat of the
tractor without first placing the PTO knob (or
lever) in the disengaged (OFF) position,
depressing the brake pedal and engaging the
parking brake. If leaving the tractor
unattended, also turn the ignition key off and
remove the key.
Briefly depress the brake pedal to release the
parking brake. Move the throttle lever into the FAST
(rabbit) position.
To travel FORWARD, slowly depress the upper
portion of the drive pedal forward until the desired
speed is achieved. See Figure 9.
To travel in REVERSE, check that the area behind
is clear then slowly depress the lower portion of the
drive pedal with the ball of your foot (NOT your heel)
until the desired speed is achieved. See Figure 9.
IMPORTANT: Do NOT attempt to change the
direction of travel when the tractor is in motion. Always
bring the tractor to a complete stop before pivoting the
drive pedal from forward to reverse or vice versa.
Figure 9
DRIVING ON SLOPES
Refer to the SLOPE GAUGE on page 7 to help
determine slopes where you may not operate safely.
WARNING: Do not mow on inclines with a
slope in excess of 15 degrees (a rise of
approximately 2-1/2 feet every 10 feet). The
tractor could overturn and cause serious
injury.
Mow up and down slopes, NEVER across.
Brake Pedal
Drive Pedal
16
Exercise extreme caution when changing direction
on slopes.
Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine.
Tall grass can hide obstacles.
Avoid turns when driving on a slope. If a turn must
be made, turn down the slope. Turning up a slope
greatly increases the chance of a roll over.
Avoid stopping when driving up a slope. If it is
necessary to stop while driving up a slope, start up
smoothly and carefully to reduce the possibility of
flipping the tractor over backward.
SETTING THE CRUISE CONTROL
NOTE: The cruise control feature should only be
utilized while traveling in the forward direction.
Slowly depress the upper portion of the drive pedal
until the desired speed is achieved.
Lightly depress the cruise control button.
While continuing to hold the cruise button in, lift
your foot from the drive pedal (you should feel the
cruise latch engage).
Once engaged, the cruise control button and the
drive pedal will lock in the “down” position, and the
tractor will maintain the same forward speed.
NOTE: Cruise control cannot be engaged at the
tractor’s fastest ground speed. If the operator should
attempt to do so, the tractor will automatically
decelerate to the fastest optimal mowing ground speed.
Disengage the cruise control using one of the following
methods:
Depress the brake pedal to disengage the cruise
control and stop the tractor.
Lightly depress the drive pedal.
To change the direction of travel to reverse when
operating with cruise control, depress the brake pedal
to disengage the cruise control and bring the tractor to a
complete stop. Then slowly depress the lower portion of
the drive pedal with the ball of your foot to travel in
reverse.
MOVING THE TRACTOR MANUALLY
Your tractor’s transmission is equipped with a
hydrostatic relief valve for occasions when it is
necessary to move the tractor manually. Activating this
valve forces the fluid in the transmission to bypass its
normal route, allowing the rear tires to "freewheel." To
engage the hydrostatic relief valve, proceed as follows:
Locate the hydrostatic bypass rod in the rear of the
tractor. See Figure 10.
Pull the hydrostatic bypass rod outward, then down,
to lock it in place.
NOTE: The transmission will NOT engage when the
hydrostatic bypass rod is pulled out. Return the rod to
its normal position prior to operating the tractor.
IMPORTANT: Never attempt to move the tractor
manually without first engaging the hydrostatic relief
valve. Doing so will result in serious damage to the
tractor’s transmission.
ENGAGING THE PTO
Engaging the PTO transfers power to the cutting deck
or other (separately available) attachments. To engage
the PTO, proceed as follows:
Move the throttle control lever to the FAST (rabbit)
position.
Models with manual PTO
Grasp the PTO lever and pivot it all the way forward
into the engaged (ON) position.
Models with electric PTO
Pull the PTO knob outward into the engaged (ON)
position. See Figure 11.
Figure 10
..
Figure 11
NOTE: Keep the throttle lever in the FAST (rabbit)
position for the most efficient use of the cutting deck or
other (separately available) attachments.
IMPORTANT: With the ignition key in the NORMAL
MOWING position, the engine or electric PTO clutch will
automatically shut off if the PTO is engaged with the
drive pedal in position for reverse travel. Refer to
SAFETY INTERLOCK SWITCHES earlier in this
section.
Hydrostatic
Bypass Rod
ON
OFF
Front View
Pull Out
Push In
17
To disengage the PTO , push the PTO knob in, or
move the PTO lever to the “Blade Stop” position.
This will cut off power to deck or other attachments.
USING THE LIFT LEVER
To raise the cutting deck, move the lift lever to the left,
then place it in the notch best suited for your
application. Refer to SETTING THE CUTTING
HEIGHT earlier in this section.
MOWING
WARNING: To help avoid blade contact or
a thrown object injury, keep bystanders,
helpers, children and pets at least 75 feet from
the machine while it is in operation. Stop
machine if anyone enters the area.
This tractor is equipped with a high quality cutting deck.
The following information will be helpful when using the
cutting deck with your tractor.
Do not mow at high ground speed, especially if a
mulch kit or grass collector is installed.
WARNING: Plan your mowing pattern to
avoid discharge of materials toward roads,
sidewalks, bystanders and the like. Also,
avoid discharging material against a wall or
obstruction which may cause discharged
material to ricochet back toward the operator.
For best results it is recommended that the first two
laps be cut with the discharge thrown towards the
center. After the first two laps, reverse the direction
to throw the discharge to the outside for the balance
of cutting. This will give a better appearance to the
lawn.
Do not cut the grass too short. Short grass invites
weed growth and yellows quickly in dry weather.
Mowing should always be done with the engine at
full throttle.
Under heavier conditions it may be necessary to go
back over the cut area a second time to get a clean
cut.
Do NOT attempt to mow heavy brush and weeds
and extremely tall grass. Your tractor is designed to
mow lawns, NOT clear brush.
Keep the blades sharp and replace the blades
when worn. Refer to the SERVICE section of this
manual for proper blade sharpening instructions.
SECTION 7: MAKING ADJUSTMENTS
WARNING: Never attempt to make any
adjustments while the engine is running,
except where specified in the operator’s
manual.
WARNING: Disconnect the spark plug
wire(s) and ground against the engine before
performing any adjustments, repairs or
maintenance.
LEVELING THE DECK
NOTE: Check the tractor’s tire pressure before
performing any deck leveling adjustments. Refer to
TIRES in the maintenance section of this manual for
further information regarding tire pressure.
Front To Rear
The front of the cutting deck is supported by a stabilizer
bar that can adjusted to level the deck from front to rear.
The front of the deck should be between 1/4-inch and
3/8-inch lower than the rear of the deck. Adjust if
necessary as follows:
With the tractor parked on a firm, level surface,
place the deck lift lever in the top notch (highest
position) and rotate the blade nearest the discharge
chute so that it is parallel with the tractor.
Measure the distance from the front of the blade tip
to the ground and the rear of the blade tip to the
ground.
The first measurement taken should be between
1/4" and 3/8" less than the second measurement.
Determine the approximate distance necessary for
proper adjustment and proceed, if necessary, to the
next step.
From the front of the tractor, loosen the outermost
hex lock nut on the end of the deck hanger rod. See
Figure 12A.
Tighten the inner hex nut front against the front
hanger bracket to raise the front of the deck; loosen
the hex nut to lower the front of the deck. See
Figure 12A.
Retighten the two lock nuts against the inner hex
nuts when proper adjustment is achieved.
Side to Side
If the cutting deck appears to be mowing unevenly, a
side to side adjustment can be performed. Adjust if
necessary as follows:
With the tractor parked on a firm, level surface,
place the deck lift lever in the top notch (highest
position) and rotate both blades so that they are
perpendicular with the tractor.
Measure the distance from the outside of the left
blade tip to the ground and the distance from the
outside of the right blade tip to the ground. Both
18
measurements taken should be equal. If they’re not,
proceed to the next step.
Loosen, but do NOT remove, the hex cap screw on
the left deck hanger bracket. See Figure 12B.
Balance the deck by using a wrench to turn the
adjustment gear (found immediately behind the hex
cap screw just loosened) clockwise/up or
counterclockwise/down.
The deck is properly balanced when both blade tip
measurements taken earlier are equal.
Retighten the hex cap screw on the left deck hanger
bracket when proper adjustment is achieved.
Figure 12
SEAT ADJUSTMENT
WARNING: Before operating this machine,
make sure the seat is engaged in the seat
stop, stand behind the machine and pull back
on seat until fully engaged into stop.
Quick-Adjust Seat (If so equipped)
To adjust the position of the seat, move the seat
adjustment lever to the left and slide the seat forward or
rearward. Make sure seat is locked into position before
operating the tractor. See Figure 13.
Knob Adjustment Seat (If so equipped)
To adjust the position of the seat on models so
equipped, loosen the two knobs on the bottom of the
seat. Slide the seat forward or backward as desired.
Retighten the two knobs.
Figure 13
PARKING BRAKE ADJUSTMENT
Never attempt to adjust the brakes while the
engine is running. Always disengage PTO,
move shift lever into neutral position, stop
engine and remove key to prevent unintended
starting.
If the tractor does not come to a complete stop when the
brake pedal is completely depressed, or if the tractor’s
rear wheels can roll with the parking brake applied, the
brake is in need of adjustment. The brake disc can be
found on the right side of the transmission in the rear of
the tractor. Adjust if necessary as follows:
Looking at the transmission from the right side of
the tractor, locate the compression spring and
brake disc. See Figure 14.
Carefully remove the cotter pin from the crown nut
on the right side of the brake assembly.
Using a feeler gauge, check the gap between the
brake disc and the brake puck. Proper gap is
0.011".
Tighten the crown nut until the proper gap is
achieved.
Install a new cotter pin (part 714-0111) on the
crown nut.
A
B
SIDE TO SIDE
Hex Cap Screw
Adjustment Gear
FRONT TO REAR
Seat
Seat Adjustment Lever
19
Figure 14
STEERING ADJUSTMENT
If the tractor turns tighter in one direction than the other,
or if the ball joints are being replaced due to damage or
wear, the steering drag links may need to be adjusted.
Adjust the drag links so that equal lengths are threaded
into the ball joint on the left side and the ball joint on the
right side:
Loosen the jam nut found on the drag link at the
rear of the ball joint. See Figure 15.
Remove the hex nut and lock washer on the top of
ball joint. See Figure 15.
Thread the ball joint toward the jam nut to shorten
the drag link. Thread the ball joint away from the
jam nut to lengthen the drag link.
Replace hex nut and lock washer and retighten the
jam nut after proper adjustment is achieved.
NOTE: Threading the ball joints too far onto the drag
links will cause the front tires to "toe-in" too far. Proper
toe-in is between 1/16" and 5/16".
Figure 15
Front tire toe-in can be measured as follows:
Place the steering wheel in position for straight
ahead travel.
In front of the axle, measure the distance
horizontally from the inside of the left rim to the
inside of the right rim. Note the distance.
Behind the axle, measure the distance horizontally
from the inside of the left rim to the inside of the
right rim. Note the distance.
The measurement taken in front of the axle should
be between 1/16" and 5/16" less than the
measurement taken behind the axle.
Adjust if necessary.
SETTING THE GAUGE WHEELS
Select the height position of the cutting deck by placing
the deck lift lever in any of the six different cutting height
notches on the right fender.
Adjust the deck wheels so that they are between ¼-inch
and ½-inch above the ground as follows.
WARNING: Keep hands and feet away
from the discharge opening of the cutting
deck.
Place the tractor on a firm and level surface, preferably
pavement. Refer to Figure 16, and proceed as follows:
Place the tractor’s deck lift handle in the normally
desired mowing height setting, then check the
gauge wheels for contact or excessive clearance
with the surface below.
If the wheels contact the surface adjust as follows:
a. Raise the deck lift handle to its highest
setting.
b. Remove the lock nuts and shoulder screws
which secure the front gauge wheels to the
deck.
Figure 16
c. Place the deck lift handle in the desired
mowing height setting.
Crown Nut
Cotter Pin
Brake Disc
Brake Puck
Brake Puck
Brake Puck
Brake PuckBrake PuckBrake PuckBrake Puck
Brake Puck
Brake Puck
Brake PuckBrake Puck
Hex Nut
Jam
Nut
Ball
Joint
Drag Link
Cotter Pin
Lock Nut
Shoulder Screw
Clevis Pin
20
d. Insert the shoulder screw with the rear gauge
wheel into the index hole that leaves
approximately 1/2" between the bottom of
the wheel and the pavement.
e. Note the position of the index hole used; then
install the other rear gauge wheel and the
front ball wheels into the corresponding index
hole of the other gauge wheel brackets.
If the gauge wheels have excessive clearance with
the surface below, lower the wheels to the index
hole that provides the approximate 1/2" clearance
as described above.
Roller (Model GT2300)
To adjust the height of the rollers found on the rear of
the mowing deck upward or downward, proceed as
follows:
Place the deck lift lever in the lowest position.
Remove the clevis pins and hairpin clips from the
deck roller brackets on the left and right sides of the
cutting deck. See Figure 16.
Position the deck roller brackets up or down
through the slots on the rear of the deck until
desired position is reached, then re-attach with the
clevis pins and hairpin clips just removed.
IMPORTANT:
Be certain that the left roller bracket and
the right roller bracket are set in the same position.
Refer to Leveling the Deck of this manual for more
detailed instructions regarding various deck
adjustments.
SECTION 8: MAINTENANCE
WARNING: Before performing any
maintenance or repairs, disengage PTO,
move shift lever into neutral position, set
parking brake, stop engine and remove key to
prevent unintended starting.
CLEANING THE ENGINE AND DECK
Any fuel or oil spilled on the machine should be wiped
off promptly.
Do NOT allow debris to accumulate around the cooling
fins of the engine or on any other part of the machine,
especially the belts and pulleys.
IMPORTANT: The use of a pressure washer or
garden hose to clean your tractor is NOT
recommended. It may cause damage to electrical
components, spindles, pulleys, bearings or the engine.
The use of water will result in a shortened life of the
tractor and reduce its serviceability.
ENGINE
Refer to the separate engine manual for engine
maintenance instructions.
Check engine oil level before each use as instructed in
the separate engine manual packed with your unit.
Read and follow instructions carefully.
CHANGING ENGINE OIL
NOTE:
Depending on the engine model found on your
tractor, it may be necessary to remove the tractor’s side
panel in order to replace the oil filter (if so equipped).
Unscrew oil fill cap and remove dipstick from the oil
fill tube. See Figure 17.
Pop open the protective cap on the end of the oil
drain valve to expose the oil drain port. See Figure
17.
Push oil drain hose (packed with unit) onto the oil
drain port. Route the opposite end of the hose into
an appropriate oil collection container with a
capacity great enough to collect the used oil.
Push the oil drain valve in slightly, then rotate
counterclockwise and pull outward to begin
draining oil. See Figure 17.
Figure 17
Service the oil filter (if so equipped) as instructed
in the separate engine manual packed with your
unit.
Perform the above steps in the opposite order after oil
has finished draining.
Refill the engine with new motor oil.
IMPORTANT: Refill the engine with the proper
capacity and weight of motor oil as instructed in the
separate engine manual.
Service air cleaner every 25 hours under normal
conditions. Clean every few hours under extremely
dusty condition. To service the air cleaner, refer to the
separate engine manual packed with your unit.
Oil Fill Cap Dipstick
Oil Drain Hose
Drain Port
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Toro 14AQ81RP544, 14AK81RK544 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues