Samsung HW-K850 Manuel utilisateur

User manual

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register your product at

www.samsung.com/register

HW-K850

2

GETTING STARTED

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage is

present inside. It is dangerous to make any

kind of contact with any internal part of this

product.

This symbol indicates that this product has

included important literature concerning

operation and maintenance.

Class II product : This symbol indicates that it does not require a safety connection to electrical

earth (ground).

AC voltage : This symbol indicates that the rated voltage marked with the symbol is AC voltage.

DC voltage : This symbol indicates that the rated voltage marked with the symbol is DC voltage.

Caution, Consult Instructions for use : This symbol instructs the user to consult the user manual

for further safety related information.

WARNING

• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation

instructions.

CAUTION

• Do not expose this apparatus to dripping or splashing. Do not put objects filled with liquids, such as vases on the

apparatus.

• To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the

power plug must be easily and readily accessible at all times.

CAUTION (for Canada)

This equipment complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or

transmitter.

This device may automatically discontinue transmission if there is no information to transmit, or an operational failure.

Note that this is not intended to prohibit the transmission of control or signaling information or the use of repetitive

codes where required by the technology.

This Class B digital apparatus complies with Canadian ICES-003.

FCC Radiation Exposure Statement

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

GETTING STARTED

ENG

3

GETTING STARTED

Important Safety Instructions

Read these operating instructions carefully before using

the unit. Follow all the safety instructions listed below.

Keep these operating instructions handy for future

reference.

1) Read these instructions.

2) Keep these Instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in

accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand,

tripod, bracket, or table specified

by the manufacturer, or sold with

the apparatus. When a cart is used,

use caution when moving the cart/

apparatus combination to avoid injury from

tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord

or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

LICENSES

Manufactured under license from Dolby Laboratories.

Dolby, Dolby Atmos, Dolby Audio, Dolby Digital Plus, Pro

Logic, and the double-D symbol are trademarks of Dolby

Laboratories.

For DTS patents, see http://patents.dts.com.

Manufactured under license from DTS Licensing Limited.

DTS, the Symbol, DTS in combination with the Symbol,

and DTS Digital Surround are registered trademarks or

trademarks of DTS, Inc. in the United States and/or other

The terms HDMI and HDMI High-Definition Multimedia

Interface, and the HDMI Logo are trademarks or

registered trademarks of HDMI Licensing LLC in the

United States and other countries.

4

GETTING STARTED

PRECAUTIONS

Ensure that the AC power supply in your house complies with the power requirements listed on the identification sticker

located on the back of your product. Install your product horizontally, on a suitable base (furniture), with enough space

around it for ventilation (3~4 inches). Make sure the ventilation slots are not covered. Do not place the unit on amplifiers

or other equipment which may become hot. This unit is designed for continuous use. To fully turn off the unit, disconnect

the AC plug from the wall outlet. Unplug the unit if you intend to leave it unused for a long period of time.

3.9 inch 3.9 inch

2.7 inch

3.9 inch

During thunderstorms, disconnect the AC plug from the

wall outlet. Voltage peaks due to lightning could damage

the unit.

Protect the product from moisture (i.e. vases), and

excess heat (e.g. a fireplace) or equipment creating

strong magnetic or electric fields. Unplug the power

cable from the AC wall socket if the unit malfunctions.

Your product is not intended for industrial use. It is for

personal use only. Condensation may occur if your

product has been stored in cold temperatures. If

transporting the unit during the winter, wait approximately

2 hours until the unit has reached room temperature

before using.

Do not expose the unit to direct sunlight or other heat

sources. This could lead to overheating and cause the

unit to malfunction.

The batteries used with this product contain chemicals

that are harmful to the environment. Do not dispose of

the battery in the general household trash. Do not

expose the battery to excess heat, direct sunlight, or fire.

Do not short circuit, disassemble, or overheat the battery.

Danger of explosion if the battery is replaced incorrectly.

Replace only with the same or equivalent type.

ENG

5

GETTING STARTED

DOLBY ATMOS®

This product supports Dolby Atmos®.

* What is Dolby Atmos®?

Atmos technology enhances existing 5.1 channel surround sound systems by adding an overhead speaker.

This envelops the listener in 360 degrees of sound, delivering an immersive, high-definition, rich, detailed, and deeper

experience. See page 24 to learn how to connect the system.

6

GETTING STARTED

CONTENTS

2 GETTING STARTED

2 Safety Information

5 Dolby Atmos®

7 What’s Included

8 DESCRIPTIONS

8 Front / Right Side Panel

9 Bottom Panel

10 Remote Control

15 INSTALLATION

15 Installing the Soundbar

15 Installing the Wall Mount

18 Detaching the Soundbar from the Wall

19 CONNECTIONS

19 Connecting the Subwoofer

22 Connecting to a TV

22 Connecting to a TV Using an HDMI (Digital)

Cable

23 Connecting to a TV Using a Digital Optical

Cable

24 Connecting to External Devices

24 Connecting Devices in Order to Use Dolby

Atmos®

25 HDMI Cable

26 Optical or Analog Audio Cable

27 FUNCTIONS

27 Input Mode

28 Bluetooth

30 Using the Multiroom App

32 Using the Network Standby On

Function

33 Software Update

35 TROUBLESHOOTING

35 Troubleshooting

36 APPENDIX

36 Specifications

Figures and illustrations in this User Manual are

provided for reference only and may differ from actual

product appearance.

ENG

7

GETTING STARTED

WHAT’S INCLUDED

BEFORE READING THE USER’S MANUAL

Note the following terms before reading the user manual.

+ Icons used in this manual

Icon Term Definition

Caution

Indicates a situation where a function does not operate or settings may be canceled.

Note

Indicates tips or instructions on the page that help you operate a function.

Check for the supplied accessories shown below.

SOUND

SOURCE

EFFECT

LEVEL

VOL WOOFER

SOUNDBAR

Remote Control /

Batteries (AA Size)

Power Cord

AC/DC Adapter

(for main unit)

HDMI Cable

C TYPE : 700mm

CENTER LINE

C C

Wall Mount Guide Holder-Screw : 2 EA Screw : 2 EA

Bracket-Wall Mount : 2 EA

● The appearance of the accessories may differ slightly from the illustrations above.

● Depending on the region, the AC plug may vary in appearance, or it may be supplied integrated with the

adapter

8

DESCRIPTIONS

FRONT / RIGHT SIDE PANEL

1 /

(Volume) Button

Controls the volume level.

The numeric value of the volume level appears in the front panel

display.

2 (Source) Button

Selects the D.IN, AUX, HDMI1, HDMI2, or BT input.

● To turn on BT PAIRING mode, press and hold this button in BT

mode.

3 (Power) Button

Turns the power on and off.

2 3

Right Side

1

Display

Displays the current mode.

● When you plug in the AC cord, the power button will begin working in 4 to 6 seconds. When you press the

power button, there will be a 20 second delay before the unit produces sound.

● When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

● If you want to enjoy sound only from the Soundbar, you must turn off the TV's speakers in the Audio Setup

menu of your TV. Refer to the owner's manual supplied with your TV.

DESCRIPTIONS

ENG

9

DESCRIPTIONS

BOTTOM PANEL

Wi-Fi SETUP SPK ADD

AUX IN

DIGITAL AUDIO IN

(OPTICAL)

HDMI OUT

(TV-ARC)

HDMI IN 1

HDMI IN 2

DC 19V

SERVICE

DC 19V

SERVICE

Wi-Fi SETUP SPK ADD

AUX IN

DIGITAL AUDIO IN

(OPTICAL)

HDMI OUT

(TV-ARC)

HDMI IN 1

HDMI IN 2

DIGITAL AUDIO IN

(OPTICAL)

HDMI OUT

(TV-ARC)

HDMI IN 1

HDMI IN 2

AUX IN

HDMI IN 1, HDMI IN 2

Inputs digital video and audio signals simultaneously using an HDMI

cable. Use when connecting a supported external device.

Wi-Fi SETUP

Press this button to connect your

Soundbar to your network using

Wi-Fi setup. (Requires a smart

device and the Samsung

Multiroom app. See page 30.)

SPK ADD

Press this button to connect the

Soundbar to a Samsung HUB

(purchased separately) or a network.

(Requires a smart device and the

Samsung Multiroom app.

See page 30.)

AUX IN

Connect to the Analog output of an external device.

DIGITAL AUDIO IN (OPTICAL)

Connect to the digital (optical) output of an external device.

HDMI OUT (TV-ARC)

Outputs digital video and audio signals simultaneously using an HDMI

cable.

DC 19V

(Power Supply In)

Connect the AC/DC power

adaptor to the power supply

jack, and then connect the

AC/DC power adaptor plug to

a wall outlet.

SERVICE

USB micro jack. To upgrade the

product's software. Requires a

USB adapter. (Sold separately.)

See page 33.

LABEL

● When disconnecting the power cable of the AC power adaptor from a wall outlet, pull the plug.

Do not pull the cable.

● Do not connect this unit or other components to an AC outlet until all connections between components

are complete.

10

DESCRIPTIONS

REMOTE CONTROL

SOUND

SOURCE

EFFECT

LEVEL

VOL WOOFER

SOUNDBAR

Power

Turns the Soundbar on and off.

SOUND

Surround Sound adds depth and spaciousness to the sound. Pressing the

SOUND button repeatedly cycles through the Surround Sound settings :

ON - SURROUND SOUND, OFF - SURROUND SOUND

• ON: Play sound over all the speakers.

• OFF: Play sound through the original source channel.

Up/Down/Left/Right

Press the indicated areas to select Up/Down/Left/Right.

Press Up/Down/

Left/Right on the button to select or set functions.

You can also activate the Wi-Fi SETUP function by pressing and holding

the

Up button on the remote for more than 5 seconds.

You can also activate the SPK ADD function of the Soundbar by pressing

and holding the Down button of the remote for more than 5 seconds.

Music Skip

Press the Right button to select the next music; press the Left button to

select the previous music.

Anynet+

Press and hold

the Right

button for about 5 seconds

to turn the Anynet+

function on or off.

(Default : ON - ANYNET+ or OFF - ANYNET+)

The Anynet+ function lets you control the Soundbar with the remote from an

Anynet+ compatible Samsung TV.

The Soundbar must be connected to the TV via an HDMI cable.

Auto Power Link

Press and hold the

Left

button for about 5 seconds to turn the Auto Power

Link function on or off.

(Default :

OFF - POWER LINK

or

ON - POWER LINK

)

Synchronizes the Soundbar to a connected Optical source via the Optical

jack so it turns on automatically when you turn on your TV. (See page 23)

The Auto Power Link function is only available in the D.IN mode.

EFFECT

You can select from 6 sound modes - STANDARD (Original Sound),

MUSIC, CLEAR VOICE, SPORTS, MOVIE, and NIGHT - depending on

the content you want to listen to.

Select the STANDARD mode if you want to enjoy the original sound.

* DRC (Dynamic Range Control)

Lets you apply dynamic range control to Dolby Digital tracks.

Press and hold the EFFECT button for about 5 seconds in standby mode

to toggle the DRC (Dynamic Range Control) function ON - DRC and

OFF - DRC.

● Operate the TV using the TV's remote control.

ENG

11

DESCRIPTIONS

SOUND

SOURCE

EFFECT

LEVEL

VOL WOOFER

SOUNDBAR

SOURCE

Press to select a source connected to the Soundbar.

* BT PAIRING mode

To turn on BT PAIRING mode in Bluetooth function, press and hold the

SOURCE button for more than 5 seconds.

Play / Pause (BT / WIFI)

Press the

p

button to pause a music temporarily.

Press the

p

button again to play the selected music.

LEVEL

The ATMOS Soundbar has 3.1.2 channel sound. Use this button to adjust

the volume of each of the speakers. Press this button, use the Left/Right

buttons to select a speaker, and then use the Up/Down buttons to increase

or decrease the level (volume).

FL FR

FTRFTL

C

Main Unit

Speaker

Displayed on OLED when

adjusting the level

Front Left FL

Front Top Left FTL

Center C

Front Right FR

Front Top Right FTR

* Network Standby On/Off

Press and hold

the LEVEL

button for about 5 seconds

to turn the Network

Standby on or off.

(See page

32

)

12

DESCRIPTIONS

SOUND

SOURCE

EFFECT

LEVEL

VOL WOOFER

SOUNDBAR

WOOFER

Push the button up or down to adjust the volume of the subwoofer to -12 or

-6 to +6.

Pressing the button reverts the subwoofer volume to level 0.

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

VOL

Push the button up or down to adjust the volume.

Mute

Press the VOL button to mute the sound. Press it again to unmute the sound.

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

(Sound Control)

Press to select TREBLE, BASS, or AUDIO SYNC. Then, use the

Up/Down buttons to adjust the TREBLE or BASS volume from -3 ~ +3.

Press and hold the

(Sound Control) button for about 5 seconds to

adjust the sound for each frequency band. 150Hz, 300Hz, 600Hz, 1.2KHz,

2.5KHz, 5KHz, and 10KHz are selectable (Left/Right) and each can be

adjusted to a setting between -6 ~ +6 (Up/Down).

If the Soundbar is connected to a digital TV and the video appears out of

sync with the audio, press the

(Sound Control) button to sync the audio

with the video. Use the Up/Down buttons to set the audio delay between

0 ms ~ 300 ms. In BT mode, the Audio Sync function may not available.

+ Controlling the Volume of Soundbar by using Your TV Remote Control

1. Press and hold the

SOUND

button for more than 5 seconds while the Soundbar is turned on.

2. "ON - TV REMOTE" appears on the Soundbar's display.

3. In the TV's menu, set the TV speaker to external speaker.

● Not available in TV ARC, BT, HDMI1 and HDMI2 modes. (Available only in D.IN (optical) and AUX

modes)

● On the TV remote control, only the volume and mute buttons are available. Other buttons are disabled.

● TV menus differ by manufacturer and model. Refer to the TV's user manual for further information.

● Manufacturers supporting this function:

- VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, GRUNDIG, Hisense, RCA

-

This function may not be compatible with your TV's remote depending on the remote control's manufacturer.

● To turn off this function, press the

SOUND

button for 5 seconds.

"OFF - TV REMOTE" appears on the Soundbar's display.

ENG

13

DESCRIPTIONS

INSERTING BATTERIES (AA BATTERY X2)

Slide the battery cover in the direction of the arrow until it is completely removed.

Insert 2 AA batteries (1.5V) in the correct +/- polarity. Slide the battery cover back into position.

USING THE HIDDEN BUTTONS

Hidden Button

Reference page

Remote Control Button Function

SOUND

TV remote control On/Off P

age 12

SOURCE

BT Paring P

age 28

p

(Play / Pause)

Auto Power Down On/Off (AUX mode) P

age 27

VOL

ID SET P

age 20

Up

WIFI SETUP P

age 10

Down

ADD SPEAKER P

age 10

Left

Auto Power Link On/Off P

age 23

Right

Anynet+ On/Off P

age 10

(Sound Control)

7 Band EQ P

age 12

EFFECT

DRC On/Off P

age 10

LEVEL

Network Standby On/Off P

age 32

14

DESCRIPTIONS

OUTPUT SPECIFICATIONS FOR THE DIFFERENT MODES OF

SOUND EFFECT

Input Effect Output

2 ch

SOUND

SOURCE

EFFECT

LEVEL

VOL WOOFER

ON

3.1.2 ch

5.1 ch 3.1.2 ch

2 ch

SOUND

SOURCE

EFFECT

LEVEL

VOL WOOFER

STANDARD

2.1 ch

5.1 ch 3.1 ch

2 ch

SOUND

SOURCE

EFFECT

LEVEL

VOL WOOFER

MUSIC

2.1 ch

5.1 ch 3.1 ch

2 ch

SOUND

SOURCE

EFFECT

LEVEL

VOL WOOFER

CLEAR VOICE

3.1 ch

5.1 ch 3.1 ch

2 ch

SOUND

SOURCE

EFFECT

LEVEL

VOL WOOFER

SPORTS

3.1.2 ch

5.1 ch 3.1.2 ch

2 ch

SOUND

SOURCE

EFFECT

LEVEL

VOL WOOFER

MOVIE

3.1.2 ch

5.1 ch 3.1.2 ch

2 ch

SOUND

SOURCE

EFFECT

LEVEL

VOL WOOFER

NIGHT

3.1 ch

5.1 ch 3.1 ch

* If the input source is Dolby Atmos®, 3.1.2 channel is outputted. The sound effect is not available.

ENG

15

INSTALLATION

INSTALLING THE SOUNDBAR

INSTALLING THE WALL MOUNT

+ Installation Precautions

● Install on a vertical wall only.

● For the installation, avoid a location with high temperature or humidity, or a wall that cannot sustain the weight of

the set.

● Check the strength of the wall. If the wall is not strong enough to support the unit, reinforce the wall or install the

unit on a different wall that can support the unit's weight.

● Purchase and use the fixing screws or anchors appropriate for the kind of wall you have (plaster board, iron board,

wood, etc.). If possible, fix the support screws into wall studs.

● Purchase wall mounting screws according to the type and thickness of the wall you will mount the Soundbar on.

- Diameter: M5

- Length: 1 3/8 inches or longer recommended.

● Connect cables from the unit to external devices before you install it on the wall.

● Make sure the unit is turned off and unplugged before you install it. Otherwise, it may cause an electric shock.

2 inches or more

1. Place the Wall Mount Guide against the wall surface.

• The Wall Mount Guide must be level.

• If your TV is mounted on the wall, install the Soundbar at least 2 inches (5 cm) below the TV.

INSTALLATION

16

INSTALLATION

Center Line

C TYPE : 700mm

CENTER LINE

C C

2. Align the Paper Template’s Center Line with the center of your TV (if you are mounting the Soundbar below your

TV), and then fix the Wall Mount Guide to the wall using tape.

● If you are not mounting below a TV, place the Center Line in the center of the installation area.

CENTER LINE

C

C TYPE : 700mm

CENTER LINE

C

C B

3. Push a pen tip or sharpened pencil tip through the center of the C-TYPE images on each end of the Guide to

mark the holes for the supporting screws, and then remove the Wall Mount Guide.

4. Using an appropriately sized drill bit, drill a hole in the wall at each marking.

● If the markings do not correspond to the positions of studs, make sure you insert appropriate anchors or

mollies into the holes before you insert the support screws. If you use anchors or mollies, make sure the

holes you drill are large enough for the anchors or mollies you use.

5. Push a screw (not supplied) through each Holder-Screw, and then screw each screw firmly into a support

screw hole.

ENG

17

INSTALLATION

6. Install 2

Bracket-Wall Mounts

in the right orientation on the bottom of the Soundbar, using 2

Screws

(M4 x L12).

Rear of the

Soundbar

Right end of the Soundbar

● When assembling, make sure the hanger parts of the Bracket-Wall Mounts are located behind the rear

of the Soundbar. See the illustration above.

7. Install the Soundbar with the attached Bracket-Wall Mounts by hanging the Bracket-Wall Mounts on the

Holder-Screws on the wall.

18

INSTALLATION

8. Slide the Soundbar down as shown above so that the Bracket-Wall Mounts rest securely on the Holder-Screws.

● Slide the Bracket-Wall Mounts down from the bottom to install it onto the Holder-Screws.

DETACHING THE SOUNDBAR FROM THE WALL

1. To separate the Soundbar from the wall mount, push it in the direction of arrow.

● Do not hang onto the installed unit and avoid striking or dropping the unit.

● Secure the unit firmly to the wall so that it does not fall off. If the unit falls off, it may cause an injury or

damage the product.

● When the unit is installed on a wall, please make sure that children do not pull any of the connecting

cables, as this may cause it to fall.

● For the optimal performance of a wall mount installation, install the speaker system at least 2 inches

(5 cm) below the TV, if the TV is mounted on the wall.

● For your safety, if you do not mount the unit on the wall, install it on a secure, flat surface where it is unlikely

to fall.

ENG

19

CONNECTIONS

CONNECTING THE SUBWOOFER

● Do not connect the power cord of this product or your TV to a wall outlet until all connections between

components are complete.

● Before moving or installing this product, be sure to turn off the power and disconnect the power cord.

● If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the STANDBY LED

on the rear will be Red after blinking Blue several times.

● If you use a device that uses the same frequency (2.4GHz) as the Soundbar near the Soundbar,

interference may cause some sound interruption.

● The maximum transmission distance of the wireless signal between the main unit and subwoofer is about

32.8 ft, but may vary depending on your operating environment. If a steel-concrete or metallic wall is

between the main unit and the wireless subwoofer, the system may not operate at all, because the wireless

signal cannot penetrate metal.

● The wireless receiving antenna is built into the wireless subwoofer. Keep the unit away from water and

moisture.

● For optimal listening performance, make sure that the area around the wireless subwoofer location is clear

of any obstructions.

AUTOMATIC CONNECTION

1. Connect a power supply to the subwoofer.

2. Connect a power supply to the Soundbar, and then press the button on the remote control or on the right side

of the Soundbar.

3. The subwoofer will be automatically connected to the Soundbar.

4. When auto pairing is complete, the blue indicators at the rear of the subwoofer turn on.

● If the red indicator at the rear of the subwoofer is on or the blue indicator flashes continuously, auto pairing

cannot occur. If this happens, connect the subwoofer manually.

● You can enjoy better sound from the wireless subwoofer by selecting a Sound Effect. (See page 10.)

● Important: Before you begin, put the batteries into the remote. See page 13 for instructions.

LINK STANDBY ID SET

POWER

LINK

Rear of Subwoofer

CONNECTIONS

20

CONNECTIONS

CONNECTING THE SUBWOOFER MANUALLY IF THE

AUTOMATIC CONNECTION FAILS

+ Before You Begin

● Make sure that the Soundbar and the subwoofer are plugged in.

● Make sure that the Soundbar is turned on.

1. Press and hold ID SET on the rear of the subwoofer for at least 5 seconds. The red indicator on the rear of the

subwoofer turns off and the blue indicator blinks.

LINK STANDBY ID SET

POWER

LINK STANDBY ID SET

POWER

LINK STANDBY ID SET

POWER

Rear of Subwoofer

2. Turn off the Soundbar.

3. Press and hold the VOL button on the remote control for at least 5 seconds with the Soundbar turned off (OFF).

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

EFFECT

LEVEL

VOL

WOOFER

SOUNDBAR

4. The ID SET message appears on the display of the Soundbar for a short period of time, and then disappears.

ID SET

Right Side of the Soundbar

5. When the blue indicator on the subwoofer blinks, turn on the power by pressing button on the right side of the

main unit or on the remote control.

La page charge ...

Samsung HW-K850 Manuel utilisateur

Samsung HW-K850 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents