Best WC33I90SB Manuel utilisateur

Model WC33I

ENGLISH .................................... 2

FRANÇAIS ................................. 17

ESPAÑOL................................... 33

In USA - BEST Hartford, Wisconsin

In CANADA - BEST Drummondville, QC, Canada

REGISTER YOUR PRODUCT ONLINE AT : www.BestRangeHoods.com/register

For additional Information visit www.BestRangeHoods.com

- 2 -

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions,

contact the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock service

panel to prevent power from being switched on accidentally. When the service discon-

necting means cannot be locked, securely fasten a prominent warning device, such

as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in ac-

cordance with all applicable codes and standards, including fire-rated construction

codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the

flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating

equipment manufacturer’s guidelines and safety standards such as those published

by the National Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code

authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other

hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any separate solid-state speed control device.

8. To reduce the risk of fire, use only metal ductwork.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding

reduces the risk of electrical shock by providing an escape wire for the electric current.

This appliance is equipped with a cord having a grounding wire with a grounding plug.

The plug must be plugged into an outlet that is properly installed and grounded.

WARNING - Improper grounding can result in a risk of electric shock.

Consult a qualified electrician if the grounding instructions are not completely understood,

or if doubt exists as to whether the appliance is properly grounded.

Do not use an extension cord. If the power supply cord is too short, have a qualified

electrician install an outlet near the appliance.

!

INTENDED FOR DOMESTIC COOKING ONLY

!

- 3 -

!

CAUTION

1. For indoor use only.

2. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not

vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or

garages.

3. Take care when using cleaning agents or detergents.

4. Avoid using food products that produce flames under the Range Hood.

5. For general ventilating use only. Do not use to exhaust hazardous or explosive

materials and vapors.

6. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall

spray, construction dust, etc. off power unit.

7. Your hood motor has a thermal overload which will automatically shut off the motor

if it becomes overheated. The motor will restart when it cools down. If the motor

continues to shut off and restart, have the hood serviced.

8. For best capture of cooking impurities, the bottom of the hood should be a minimum

of 24” and a maximum of 30” above the cooking surface. See “Install Mounting

Bracket” section for mounting restrictions.

9. Two installers are recommended because of the large size and weight of this hood.

10. This product is equipped with a thermostat which may start blower automatically. To

reduce the risk of injury and to prevent power from being switched on accidentally,

switch power off at service panel and lock or tag service panel.

11. Please read specification label on product for further information and requirements.

WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking at high heat or when flambéing food (i.e. Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan

or filter.

D. Use proper pan size. Always use cookware appropriate for the size of the surface

element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP

GREASE FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off

the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out imme-

diately, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion

will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you already know how to oper-

ate it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

- 4 -

OPERATION

Controls

The hood is operated using the (5) push buttons located on the front edge of the

hood. Fig. 1.

The Light On/Off switch turns the lights on to high intensity and turns them off.

The Light Dimmer switch alternates light intensity from low to high.

The Blower Off/Speed switch turns the blower off and changes blower speed to four

different speed settings: high, medium-high, medium-low and low speed. Depress

and hold the button for 2 seconds to turn the blower off.

The Blower On/Speed switch turns the blower on to four different speed settings:

Low, medium-low, medium-high and high speed.

The Blower LED Indicators illuminate for each selected speed.

The Time Delay switch activates a delay off feature. When pushed, the blower will

continue to operate at the current speed setting for 10-minutes before automatically

turning itself off. The LED (on the right) flashes during operation.

The LED (on the right) is also used as a filter clean reminder. It will flash after 30

hours of operation - indicating the need to clean the filters.

The Filter Alarm Reset switch is used to reset the 30-hour filter timer. After filters

are cleaned or replaced, press this switch once to reset the filter clean alarm.

HEAT SENTRY™

Your hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a

device that will turn on or speed up the blower if it senses excessive heat above

the cooking surface.

1) If blower is OFF - it turns blower ON to HIGH speed.

2) If blower is ON at a lower speed setting - it turns blower up to HIGH speed.

When the temperature level drops to normal, the blower will return to its original

setting.

WARNING

The HEAT SENTRY thermostat can start the blower even if the hood is turned

OFF. When this occurs, it is impossible to turn the blower OFF with its switch.

If you must stop the blower, do it from the main electrical panel.

Light

On / Off

FIG. 1

Light

Dimmer

Blower

Off / Speed

Blower

On / Speed

Blower LED

Indicators

Time Delay /

Filter Alarm

Reset

LED

- 5 -

HALOGEN BULBS

This range hood requires two halogen

bulbs (Type T4, 120Volt, 25Watt Max,

G9 Base).

WARNING: Always switch off the

electrical supply before carrying out

any operation on the appliance.

To change bulbs:

1. Open the cover by prying from the

proper slots. Fig. 2.

2. Remove the bulbs by pulling sideways. (DO NOT ROTATE).

!

CAUTION: Bulbs may be hot.

3. Replace with Type T4, 120Volt, 25Watt Max, G9 Base halogen bulbs. Do not

touch replacement bulbs with bare hands!

FIG. 2

CLEANING AND MAINTENANCE

Proper maintenance of the Range Hood will assure proper performance of the unit.

Motor

The motor is permanently lubricated and never needs oiling. If the motor bearings make

excessive or unusual noise, replace the motor with the exact service motor. The impeller

should also be replaced.

Grease Filter

The grease filter should be cleaned frequently. Use a warm detergent solution. Grease filter

is dishwasher safe.

Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of

the filter may occur if using phosphate detergents, or as a result of local water conditions

- but this will not affect filter performance. This discoloration is not covered by the warranty.

See “INSTALL FILTERS” section for removal and installation instructions.

Non-ducted Recirculation Filter

The non-ducted recirculation filter should be changed every 6 months. Replace more often if

your cooking style generates extra grease, such as frying and wok cooking. See “INSTALL

FILTERS” section for removal and installation instructions.

Stainless Steel Cleaning

DO:

• Regularly wash with clean cloth or rag

soaked with warm water and mild soap

or liquid dish detergent.

• Always clean in the direction of original

polish lines.

• Always rinse well with clear water (2 or 3

times) after cleaning. Wipe dry completely.

• You may also use a specialized household

stainless steel cleaner.

DON’T:

•

Use any steel or stainless stell wool or any

other scrapers to remove stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction

residues reach the hood. During construc-

tion/renovation, cover the range hood to

make sure no dust sticks to the stainless

steel surface.

Avoid: When choosing a detergent

• Any cleaners that contain bleach will attack stainless steel

• Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.

• Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc.,

are highly explosive and should never be used close to a range.

- 6 -

PREPARE THE HOOD

Unpack hood and check contents.

You should receive:

1 - Hood

1 - Decorative Flue Assembly

1 - Parts Bag containing:

2 - Mounting Brackets

1 - Damper

1 - Flue Mounting Bracket

8 - Mounting Screws (4.8 x 38mm Pan Head)

2 - Mounting Screws (3.9 x 9.5mm Pan Head)

2 - Mounting Screws (3.9 x 6mm Flat Head)

8 - Drywall Anchors

1 - Installation Instructions

MOUNTING

BRACKET

DAMPER

FLUE MOUNTING

BRACKET

8 MOUNTING SCREWS

(4.8 x 38mm Pan Head)

8 DRYWALL

ANCHORS

2 MOUNTING

SCREWS (3.9 x

9.5mm Pan Head)

DECORATIVE

FLUE

2 MOUNTING

SCREWS (3.9 x

6mm Flat Head)

FIG. 3

- 7 -

ROOF CAP

6-INCH

ROUND DUCT

DECORATIVE

FLUE

HOOD

WALL

CAP

6-INCH

ROUND

ELBOW

24” TO 30” ABOVE COOKING SURFACE

(see “INSTALL MOUNTING BRACKETS”

section for mounting restrictions)

INSTALL THE DUCTWORK

DUCTED HOODS ONLY

CAUTION: To reduce the risk of fire,

use only metal ductwork.

1. Decide where the ductwork will run

between the hood and the outside.

Fig. 4.

2. A straight, short duct run will allow

the hood to perform most efficiently.

3. Long duct runs, elbows, and transi-

tions will reduce the performance of

the hood. Use as few of them as pos-

sible. Larger ducting may be required

for best performance with longer duct

runs.

4. Install a roof or wall cap. Connect

round metal ductwork to cap and

work back towards hood location. Use

duct tape to seal the joints between

ductwork sections.

INSTALL ELECTRICAL

DUCTED and NON-DUCTED HOODS

WARNING : Electrical wiring must

be done by a qualified person(s) in

accordance with all applicable codes

and standards. This range hood must

be properly grounded. Turn off electri-

cal power at service entrance before

wiring.

1. Plan where the hood will be located

above the cook top. Refer to the

“INSTALL MOUNTING BRACKET”

section for hood mounting height

options.

2. Install a standard 2” x 4” wall outlet

box and 3-blade 125 volt, 15 Amp

grounded receptacle. Fig. 5.

3. Mount the center of the wall outlet 10”

to 13” above the top of the hood.

4. Locate the box and the receptacle

within boundary shown and off center

of the ductwork (to allow for power

cord plug and flue clearance).

FIG. 4

FIG. 5

CENTERLINE

OF HOOD

3-3/8”

6-3/4”

10 - 13”



- 8 -

INSTALL MOUNTING

BRACKETS

DUCTED and NON-DUCTED HOODS

1. Construct wood wall framing that

is flush with interior surface of wall

studs. Fig. 6.

Make sure:

a) the framing is centered over in-

stallation location.

b) the height of the framing will al-

low the mounting brackets to be

secured to the framing within the

dimensions shown.

2. After wall surface is finished, se-

cure each mounting bracket to fram-

ing with (2) 4.8 x 38 mm mounting

screws. See chart below for mounting

bracket location.

Note : Minimum hood distance above cook top must not be less than 24”. A maximum

of 30” above cook top is highly recommended for best capture of cooking impurities.

Distances over 30” are at the installer and user’s discretion; and if ceiling height

and flue length permit.

HOOD DISTANCE ABOVE 36” HIGH COOK TOP (see note below)

30”

MOUNTING BRACKET LOCATION ABOVE 36” HIGH COOK TOP

CEILING

HEIGHT

8 FEET

24” 25” 26” 27” 28” 29”

9 FEET

FIG. 6

DUCTED OR

NON-DUCTED

DUCTED OR

NON-DUCTED

DUCT

METHOD

35”

36”

37”

38” 39”

40” 41”

35” 36”

37”

FRAMING BEHIND

WOOD CROSS

SUPPORT

WOOD CROSS

SUPPORT BEHIND

DRYWALL

12-1/2”

2-3/16”

- 9 -

INSTALL FLUE MOUNTING

BRACKET

DUCTED AND NON-DUCTED HOODS

1. Assemble the flue mounting bracket,

adjusting outside width as shown.

Fig. 7.

2. Carefully center the mounting bracket

directly over the range hood location.

3. Secure the bracket assembly to the

ceiling using (2) 4.8 x 38 mm mount-

ing screws and drywall anchors.

Fig. 8. Make sure the bracket is pushed

into the corner, tight against the wall

and centered over the hood.

FLUE MOUNTING BRACKET

7-11/16”

FIG. 7

3.9 x 6 mm FLAT HEAD

BRACKET SCREWS

FIG. 8

4.8x38mm

MOUNTING SCREWS

DRYWALL ANCHORS

DRYWALL

ANCHORS

FIG. 11

INSTALL THE HOOD

Note: Remove the plastic protective

film from all exterior surfaces, deco-

rative flues and filters, prior to final

installation.

DUCTED and NON-DUCTED

INSTALLATION

1. Install hood onto the wall mounting

bracket. Make sure hood is level with

floor. Fig. 9.

2. Make sure hood is level with floor. Use

adjustment screws to level. Fig 10.

3. Mark and install (2) additional drywall

anchors and screws as shown. Fig. 11.

4. Secure hood to wall with (2) 4.8 x 38

mm mounting screws and (2) drywall

anchors. Figs. 10 & 11.

FIG. 10

4.8 x 38 mm

SCREWS

FIG. 9

4.8 x 38 mm

SCREWS

- 10 -

FIG.12

DAMPER

6-INCH DIA.

METAL DUCT

DUCTED INSTALLATION ONLY

1. Press the damper into the duct

connector on the hood. Fig. 12.

2. Run 6-inch diameter metal ductwork

to the outside location.

3. Install an appropriate wall or roof cap

with damper to exhaust the air to the

outside.

4. Tape all duct joints with aluminum

duct tape.

5. Plug power cord into wall outlet.

6. Install upper and lower decorative

flues onto the range hood. Fig. 13.

- Vents are concealed on 8-foot

ceilings.

- Vents are exposed on 9-foot

ceilings.

7. Secure upper flue to flue mounting

bracket with (2) 3.9 x 6 mm screws.

Fig. 14.

FIG.13

FIG.14

DUCT

CONNECTOR

VENTS

CONCEALED

VENTS

EXPOSED

POWER

CORD

3.9 x 6 mm

SCREWS

FLUE

MOUNTING

BRACKET

- 11 -

NON-DUCTED INSTALLATION ONLY

Note: Purchase Model ANKWC33 Non-

ducted Recirculation Kit.

1. Do not install damper supplied with

the range hood.

2. Attach the 5” to 6” adapter to blower

discharge and tape joint with

aluminum duct tape. Fig. 15.

3. Install the plenum to the upper

decorative flue using (4) 3.4 x 15 mm

screws provided as shown. Fig. 16.

4. Attach 5-inch expandable ducting

to the plenum and tape joint with

aluminum duct tape. Fig. 17.

FIG.15

FIG.16

FIG.17

5” TO 6”

ADAPTER

3.4 x 15 mm

SCREWS

- 12 -

5. Plug power cord into wall outlet.

6. Temporarily secure the upper and

lower flue together with duct tape as

shown. Fig. 18.

7. Lift the flue into position. Secure upper

flue to the flue mounting bracket with

(2) 3.9 x 6 mm screws. Fig. 18.

8. Stretch expandable duct, attach it to

the 5”-to-6” adapter and tape duct

joints. Fig. 19.

9. Remove tape from flues and lower

into position on the hood.

10. Tabs on lower flue slip into slots on

top of the hood. Fig. 19.

FIG.18

3.9 x 6 mm

SCREWS

TAPE

POWER

CORD

FIG.19

TAB

SLOT

5” TO 6”

ADAPTER

- 13 -

ADJUST HOOD HEIGHT

1. Loosen (3) screws on upper decora-

tive trim. Fig. 20.

2. Slide trim up to increase panel open-

ing from 13-3/4” to 14-3/8”.

3. Re-tighten (3) screws on upper deco-

rative trim.

ADJUST HOOD DEPTH

1. Loosen (2) screws on top of the range

hood housing. Fig. 21.

2. Slide the front hood panel forward

to increase hood depth from 13” to

14-1/2”.

3. Re-tighten (2) screws on the top of

the range hood.

INSTALL DECORATIVE

PANEL

Note: The custom panel and material

must comply with all local building

codes.

1. Cut 3/4” panel to fit the adjustable

range hood opening.

2. Fasten the panel to the range hoods

front panel with appropriately-sized

screws. Fig. 22.

3. Make sure the panel is properly se-

cured to the range hood after instal-

lation.

FIG.20

35-3/8”

MIN 13-3/4”

MAX 14-3/8”

3/4”

MAX 19-13/16”

FIG.21

MIN 13”

MAX 14-1/2”

FIG.22

- 14 -

INSTALL FILTERS

DUCTED AND NON-DUCTED HOODS

1. To remove the GREASE filter, push in

latch tab to disengage the filter from

the hood. Tilt the filter downward and

remove. Fig. 23.

2. To install the GREASE filter, align rear

filter tabs with slots in the hood. Push

latch tab in, push filter into position

and release. Make sure the filter is

securely engaged after installation.

Fig. 23.

NOTE: Prior to use, remove protective

film from the filter frame.

NON-DUCTED HOODS ONLY

1. Remove grease filter. Fig. 23.

2. Remove charcoal filters from protec-

tive wrapping.

3. Grasp the charcoal filters and turn

clockwise one quarter turn onto blo-

wer. Fig. 24.

4. Install GREASE filter after charcoal

filter in installed.

WARRANTY

ONE YEAR LIMITED WARRANTY FOR BEST PRODUCTS

Broan-NuTone LLC (Broan-NuTone) warrants to the original consumer purchaser of Best products that such products

will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE

ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRAN-

TIES OR MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which

is found to be defective under normal use and service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDES-

CENT BULBS, FUSE, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING.

This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject

to misuse, negligence, accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation or

installation contrary to recommended installation instructions.

The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states

do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE’S OPTION, SHALL BE THE

PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LI-

ABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH

PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This

warranty supersedes all prior warranties.

To qualify for warranty service, you must (a) notify Broan-NuTone at the address stated below or telephone number stated

below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part.

At the time of requesting warranty service, you must present evidence of the original purchase date.

In USA - Best®, 926 W. State Street, Hartford, WI 53027 (800-558-1711)

In Canada - Best®, 550 Lemire Blvd., Drummondville, QC J2C 7W9 (866-737-7770)

www.BestRangeHoods.com

FIG.23

FIG.24

CHARCOAL

FILTERS (2)

- 15 -

SERVICE PARTS

KEY NO. PART NO. DESCRIPTION

9 B08087824 GREASE FILTER

14 B02300233 CONDENSER

16 BE3351250 ELECTRICAL BOX SUPPORT

26 B02300890 LAMP BULB

37 B02300804 KNOB

38 B03295595 ELECTRICAL PRINTED CIRCUIT BOX

BW0000055 ELECTRICAL PRINTED CIRCUIT BOARD

BOX (INCLUDES KEY NO. 228 & 230)

45 BW0000040 BLOWER

48 B02310260 MOTOR (CLOCKWISE)

49 B03295071 FAN (CLOCKWISE)

53 B03204177 RUBBER WASHER

58 B03295018 OUTLET REDUCTION

60 B02300249 FEEDER CABLE

62 B08093087 BLOWER BRACKET

67 B02300958 WIRES

86 B08088378 OUTLET FLANGE

92 BE3350823 SWITCH BOARD BOX SUPPORT

107 B03202287 CABLE STOP

114 B03290499 RUNNER WIRES

118 BE3350073 BOTTOM DUCT EXT.

119 BE3350074 UPPER DUCT EXT.

120 B08091367 TELESCOPIC DUCT UPPER BRACKET

122 B03295016 RISER

130 B003102675 FRONT PANEL

147 BR2300132 JUNCTION CLAMP

154 B03202286 FEEDER CABLE STOP

166 B08080852 ELECTRICAL PRINTED CIRCUIT BOARD

167 B03295596 ELECTRICAL BOX COVER

223 B03294171 SWITCH BUTTON

228 B08080265 CONTROLS PRINTED CIRCUIT BOARD

230 B03294165 SWITCH BOARD BOX COVER

234 B03293009 SWITCH BOARD BOX

340 BE3350821 EXTERIOR RIGHT SIDE

341 BE3350822 EXTERIOR LEFT SIDE

342 B08092925 UPPER CLOSURE PANEL

407 BE3351249 BLOWER SUPPORT BRACKET

415 B03202454 FAIRLEAD

474 B02300918 HALOGEN LAMP

503 B02011452 EXPANDABLE DUCT

* B06002080 BLOWER ASSEMBLY

(INCLUDES KEY NO. 45,48,49,53)

* B06145120 ELECTRICAL INSTALLATION ASSEMBLY

(INCLUDES KEY NO.

14,38,60,67,147,166,167,223,234)

* B06103881 SWITCH BOX ASSEMBLY

(INCLUDES KEY NO. 38,67,223,234)

* B080810954 FITTING SET (INCLUDES KEY NO. 120)

- 16 -

SERVICE PARTS

16

120

67

114

122

58

86

119

118

62

154

107

474

26

9

415

341

130

342

340

92

234

38

(W0000055)

223

228

230

407

60

167

147

166

38

(03295595)

14

49

53

45

48

503

37

99044738A

- 17 -

Modèle WC33I

Aux ÉTATS-UNIS - BEST Hartford, Wisconsin

Au CANADA - BEST Drummondville, QC, Canada

ENREGISTREZ VOTRE PRODUIT EN LIGNE À L’ADRESSE: www.BestRangeHoods.com/register

Pour en savoir plus, visitez le site www.BestRangeHoods.com

ENGLISH .................................... 2

FRANÇAIS ................................. 17

ESPAÑOL................................... 33

- 18 -

VEUILLEZ LIRE ET CONSERVER CES INSTRUCTIONS

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE, D’ÉLECTROCUTION OU DE BLES-

SURES PHYSIQUES, RESPECTEZ LES INSTRUCTIONS CI-DESSOUS :

1. Utilisez cet appareil uniquement de la manière prévue par le fabricant. Si vous avez

des questions, contactez le fabricant à l’adresse ou au numéro de téléphone indiqués

dans la garantie.

2. Avant d’effectuer l’entretien ou le nettoyage de l’appareil, mettez-le hors tension sur

le panneau de service et verrouillez ce dernier pour éviter que l’appareil soit mis

sous tension par inadvertance. S’il n’est pas possible de verrouiller le dispositif de

déconnexion, apposez un avertissement bien visible (par exemple une étiquette) sur

le panneau de service.

3. L’installation et le raccordement électrique doivent être effectués par du personnel

qualifié conformément à toutes les réglementations et normes en vigueur, y compris

celles concernant les constructions cotées pour leur résistance au feu.

4. Afin d’éviter un refoulement lors de l’utilisation d’équipements à combustible, une

quantité d’air suffisante est nécessaire pour assurer une combustion et un échappe-

ment adéquats des gaz à travers le conduit (la cheminée). Suivez les consignes du

fabricant de l’équipement chauffant et les normes de sécurité publiées, entre autres,

par l’Association nationale de protection contre l’incendie (NFPA) et l’American Society

for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), ainsi que les

réglementations locales.

5. Quand vous effectuez une découpe ou un forage dans un mur ou un plafond, veillez à

ne pas endommager des câblages électriques ou d’autres équipements non visibles.

6. Les soufflantes canalisées doivent toujours être dirigées vers l’extérieur.

7. N’utilisez pas cet appareil avec un dispositif de commande de vitesse transistorisée

séparé.

8. Pour réduire les risques d’incendie, utilisez uniquement des canalisations en métal.

INSTRUCTIONS DE MISE À LA TERRE

Cet appareil doit être mis à la terre. En cas de court-circuit électrique, la mise à la terre

réduit le risque d’électrocution grâce à un fil permettant au courant électrique de s’échap-

per. Cet appareil est doté d’un cordon ayant un fil de terre, ainsi que d’une fiche de mise

à la terre. La fiche doit être branchée dans une prise bien installée et mise à la terre.

AVERTISSEMENT - Une mise à la terre inappropriée peut donner lieu à un risque

d’électrocution.

Consultez un électricien qualifié si vous ne comprenez pas parfaitement les instructions

de mise à la terre ou si vous n’êtes pas certain(e) que l’appareil est mis à la terre comme

il se doit.

N’utilisez pas de rallonge. Si le cordon est trop court, demandez à un électricien d’installer

une prise près de l’appareil.

!

CONÇUE POUR LES CUISINES PRIVÉES UNIQUEMENT

!

- 19 -

!

ATTENTION

1. Uniquement pour l’utilisation intérieure.

2. Pour réduire le risque d’incendie et obtenir un échappement d’air adéquat, veillez

à bien canaliser l’air vers l’extérieur. Ne ventilez pas l’air d’échappement vers des

espaces confinés, des plafonds, des combles, des vides sanitaires ou des garages.

3. Soyez prudent(e) quand vous utilisez des agents de nettoyage ou des détergents.

4. Évitez d’utiliser sous la hotte de cuisine des denrées alimentaires produisant des flammes.

5. À utiliser uniquement pour la ventilation générale. N’utilisez pas la hotte pour l’échap-

pement de matériaux ou de vapeurs comportant un danger ou un risque d’explosion.

6. Pour éviter que le roulement moteur s’endommage et que des hélices deviennent

bruyantes ou déséquilibrées, faites en sorte que le bloc d’alimentation n’entre pas en

contact avec un atomiseur pour cloisons sèches, de la poussière de construction, etc.

7. Le moteur de la hotte est doté d’un rupteur thermique qui éteint automatiquement

le moteur en cas de surchauffe. Le moteur redémarrera après avoir refroidi. Si le

moteur s’éteint et se rallume constamment, faites réparer la hotte.

8. Pour mieux capturer les impuretés de cuisson, la partie inférieure de la hotte doit se

trouver au minimum à 60cm (24 po) et au maximum à 75cm (30 po) au-dessus de

la surface de cuisson. Consultez la section «Installation du support de montage»

pour connaître les restrictions de montage.

9. Étant donné la taille et le poids de la hotte, il est conseillé d’avoir recours à deux

personnes pour la monter.

10. Ce produit est doté d’un thermostat qui peut activer la soufflante automatiquement. Pour

éviter les risques de blessure et l’allumage accidentel de la hotte, mettez-la hors tension

sur le panneau de service et verrouillez ce dernier ou fixez-y une étiquette d’avertissement.

11. Pour en savoir plus et connaître les exigences sur le produit, veuillez lire l’étiquette

des spécifications.

AVERTISSEMENT

POUR RÉDUIRE LE RISQUE D’UN FEU DE FRITURE SUR LA TABLE DE CUISSON

A. Ne laissez jamais les appareils de surface sans surveillance quand ils sont sur un réglage

élevé. Les débordements peuvent provoquer de la fumée et des déversements gras

risquant de prendre feu. Chauffez les huiles lentement sur un réglage bas ou moyen.

B. Allumez toujours la hotte quand vous cuisinez à une chaleur élevée ou quand vous

flambez des aliments (p. ex. des crêpes Suzette, des cerises jubilé ou du bœuf au

poivre flambé).

C. Nettoyez souvent les ventilateurs d’aération. Évitez que la graisse ne s’accumule sur

le ventilateur ou le filtre.

D. Utilisez des poêles de la taille appropriée. Utilisez toujours des ustensiles de cuisine

adaptés à la taille de l’élément de surface.

POUR RÉDUIRE LE RISQUE DE BLESSURES PHYSIQUES EN CAS DE FEU DE

FRITURE SUR LA TABLE DE CUISSON, VEUILLEZ PROCÉDER COMME SUIT:*

1. ÉTOUFFEZ LES FLAMMES avec un couvercle hermétique, une plaque à biscuits ou

un plateau en métal, puis éteignez le brûleur. SOYEZ PRUDENT(E) AFIN D’ÉVITER

LES BRÛLURES. Si les flammes ne s’éteignent pas immédiatement, ÉVACUEZ LES

LIEUX ET APPELEZ LE SERVICE DES POMPIERS.

2. NE SAISISSEZ JAMAIS UNE POÊLE ENFLAMMÉE, vous risquez de vous brûler.

3. N’UTILISEZ JAMAIS D’EAU ni de torchons ou serviettes mouillé(e)s: cela donnerait

lieu à une violente explosion de vapeur.

4. Utilisez un extincteur UNIQUEMENT si:

A. Vous savez qu’il s’agit d’un extincteur de Classe ABC et savez déjà comment

vous en servir.

B. L’incendie est de petite taille et confiné à l’endroit où il a commencé.

C. Le service des pompiers a été averti.

D. Vous pouvez éteindre l’incendie en ayant une sortie derrière vous.

* Basé sur «Kitchen Fire Safety Tips», publié par la NFPA.

- 20 -

FONCTIONNEMENT

Commandes

La hotte s’utilise à l’aide des 5boutons-poussoirs situés sur le devant de la hotte. Fig. 1.

Le commutateur Marche/arrêt lumière permet d’allumer et d’éteindre les lumières

à haute intensité.

Le commutateur Atténuation lumière permet de passer de la haute à la basse

intensité.

Le commutateur Extinction/vitesse soufflante permet d’éteindre la soufflante ou

de régler sa vitesse sur quatre positions: haute, moyenne-haute, moyenne-basse et

basse. Maintenez le bouton enfoncé pendant 2secondes pour éteindre la soufflante.

Le commutateur Démarrage/vitesse soufflante permet d’allumer la soufflante et

de la régler sur quatre vitesses: basse, moyenne-basse, moyenne-haute et haute.

Les Témoins de la soufflante s’allument pour chaque vitesse sélectionnée.

Le commutateur de Minuterie/Réinitialisation alarme du filtre active une fonction

de temporisation. Quand il est enfoncé, la soufflante continue à fonctionner à la

vitesse de réglage actuelle pendant 10minutes avant de s’éteindre automatiquement.

La DEL (à droite) clignote pendant le fonctionnement.

La DEL (à droite) sert aussi de rappel de nettoyage du filtre. Elle clignote après

30heures d’utilisation pour indiquer que les filtres doivent être nettoyés.

Le commutateur Réinitialisation alarme du filtre permet de réinitialiser la minuterie

de 30heures du filtre. Après avoir nettoyé ou remplacé les filtres, appuyez une fois

sur ce commutateur pour réinitialiser l’alarme de nettoyage du filtre.

HEAT SENTRY™

La hotte est équipée d’un thermostat HEAT SENTRY™. Ce dispositif active ou

accélère la soufflante s’il détecte une chaleur excessive au-dessus de la surface

de cuisson.

1) Si la soufflante est arrêtée, il l’allume sur la vitesse HAUTE.

2) Si la soufflante est allumée à une vitesse basse, il la fait passer à la vitesse HAUTE.

Quand la température redevient normale, la soufflante retourne au réglage d’origine.

AVERTISSEMENT

Le thermostat HEAT SENTRY peut activer la soufflante même si la hotte est

éteinte. Dans ce cas, il est impossible de désactiver la soufflante avec le

commutateur d’arrêt. Si vous devez arrêter la soufflante, faites-le depuis le

panneau électrique principal.

Marche/arrêt

lumière

FIG. 1

Atténuation

lumière

Extinction/

vitesse

soufflante

Démarrage/

vitesse

soufflante

Témoins (DEL)

de la

soufflante

Minuterie /

Réinitialisation

alarme du filtre

DEL

MARCHE/+MARCHE ARRÊT/- ARRÊT

La page charge ...

Best WC33I90SB Manuel utilisateur

Best WC33I90SB Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents