DR PRO Series Le manuel du propriétaire

Marque: DR

Modèle: PRO Series

Catégorie: Groupes électrogènes

Taper: Le manuel du propriétaire

PRO Series Diesel Portable

Generator

Owner’s Manual

MODEL:________________________

SERIAL:________________________

DATE PURCHASED:______________

product at:

www.drpower.com

1-855-447-3734

SAVE THIS MANUAL FOR FUTURE REFERENCE

000703

Table of Contents

Section 1 Introduction and Safety 1

Introduction ..................................... 1

Safety Rules .................................... 1

Safety Symbols and Meanings ........ 1

Exhaust and Location Hazards ....... 2

Electrical Hazards ........................... 3

Fire Hazards .................................... 3

Standards Index .............................. 3

Section 2 General Information and

Setup .............................................. 4

Know Your Generator ..................... 5

Emissions ........................................ 5

Hour Meter ...................................... 6

Connection Plugs ............................ 6

Remove Contents from Carton ....... 7

Assembly ......................................... 7

Battery Installation (if equipped) ...... 8

Add Engine Oil ................................ 8

Fuel ................................................. 9

Section 3 Operation .................... 10

Operation and Use Questions ....... 10

Before Starting Engine .................. 10

Prepare Generator for Use ............ 10

Grounding the Generator When Used

as a Portable .................................10

Know Generator Limits ..................11

Transporting/Tipping of the Unit ....11

Starting Pull Start Engines .............12

Starting Electric Start Engines .......12

Low Oil Pressure Switch ................13

Section 4 Maintenance and

Troubleshooting ..........................14

Maintenance ..................................14

Maintenance Schedule ..................14

Preventive Maintenance ................14

Engine Maintenance ......................14

Battery Replacement (if equipped) 16

Valve Clearance ............................16

Storage ..........................................16

Troubleshooting .............................17

Notes .............................................19

(000394)

WARNING

Breathing diesel engine exhaust exposes you

to chemicals known to the State of California

to cause cancer and birth defects or other

reproductive harm.

• Always start and operate the engine in a

well-ventilated area.

• If in an enclosed area, vent the exhaust to

the outside.

• Do not modify or tamper with the exhaust

system.

• Do not idle the engine except as necessary.

For more information go to

www.P65Warnings.ca.gov/diesel.

Owner’s Manual for Portable Generator 1

Section 1 Introduction and Safety

Introduction

Thank you for purchasing a DR Power Equip-

ment product. This unit has been designed to

provide high-performance, efficient operation,

and years of use when maintained properly.

If any section of the manual is not understood,

contact Customer Service at 1-855-447-3734,

or www.drpower.com with any questions or

concerns.

The owner is responsible for proper mainte-

nance and safe use of the equipment. Before

operating, servicing or storing this generator:

• Study all warnings in this manual and on

the product carefully.

• Become familiar with this manual and the

unit before use.

• Refer to the Assembly section of the man-

ual for instructions on final assembly proce-

dures. Follow the instructions completely.

Save these instructions for future reference.

ALWAYS supply this manual to any individual

that will use this machine.

The information in this manual is accurate

based on products produced at the time of

publication. The manufacturer reserves the

right to make technical updates, corrections,

and product revisions at any time without

notice.

Safety Rules

The manufacturer cannot anticipate every

possible circumstance that might involve a

hazard. The alerts in this manual, and on tags

and decals affixed to the unit, are not all inclu-

sive. If using a procedure, work method, or

operating technique that the manufacturer

does not specifically recommend, verify that it

is safe for others and does not render the

equipment unsafe.

Throughout this publication, and on tags and

decals affixed to the unit, DANGER, WARN-

ING, CAUTION, and NOTE blocks are used to

alert personnel to special instructions about a

particular operation that may be hazardous if

performed incorrectly or carelessly. Observe

them carefully. Alert definitions are as follows:

NOTE: Notes contain additional information

important to a procedure and will be found

within the regular text of this manual.

These safety alerts cannot eliminate the haz-

ards that they indicate. Common sense and

strict compliance with the special instructions

while performing the action or service are

essential to preventing accidents.

Safety Symbols and Meanings

• If you start to feel sick, dizzy, or weak after

the generator has been running, move to

fresh air IMMEDIATELY. See a doctor, as

you could have carbon monoxide poison-

ing.

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

(000001)

DANGER

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

(000002)

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

(000003)

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

DANGER

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is

a poison you cannot see or smell.

NEVER use inside a home

or garage, EVEN IF doors

and windows are open.

Only use OUTSIDE and

far away from windows,

doors, and vents.

000657

(000103)

DANGER

Asphyxiation. Running engines produce carbon

monoxide, a colorless, odorless, poisonous gas.

Carbon monoxide, if not avoided,

will result in death or serious injury.

2 Owner’s Manual for Portable Generator

• Follow procedures in the Maintenance and

Troubleshooting section. For safety rea-

sons, if you feel uncomfortable performing

any task, call 1-855-447-3734 for assis-

tance.

Exhaust and Location Hazards

• If you start to feel sick, dizzy, or weak after

the generator has been running, move to

fresh air IMMEDIATELY. See a doctor, as

you could have carbon monoxide poison-

ing.

• NEVER run a generator indoors or in a

partly enclosed area such as garages.

(000179b)

DANGER

Asphyxiation. The exhaust system must be properly

maintained. Do not alter or modify the exhaust system

as to render it unsafe or make it noncompliant with

local codes and/or standards. Failure to do so will

result in death or serious injury.

(000104)

DANGER

Electrocution. Water contact with a power source,

if not avoided, will result in death or serious injury.

(000116)

DANGER

Electrocution. Turn utility and emergency

power supplies to OFF before connecting power

source and load lines. Failure to do so will result

in death or serious injury.

(000146)

WARNING

Equipment and property damage. Do not alter

construction of, installation, or block ventilation for

generator. Failure to do so could result in unsafe

operation or damage to the generator.

(000178a)

Asphyxiation. Always use a battery operated carbon

monoxide alarm indoors and installed according to

the manufacturer’s instructions. Failure to do so

could result in death or serious injury.

WARNING

(000250)

WARNING

Equipment and property damage. Do not operate unit on

uneven surfaces, or areas of excessive moisture, dirt, dust

or corrosive vapors. Doing so could result in death, serious

injury, property and equipment damage.

(000111)

WARNING

Moving Parts. Keep clothing, hair, and appendages

away from moving parts. Failure to do so could

result in death or serious injury.

(000108)

WARNING

Hot Surfaces. When operting machine, do not

touch hot surfaces. Keep machine away from

combustables during use. Hot surfaces

could result in severe burns or fire.

(000142a)

Personal injury. Do not insert any object through the

air cooling slots. Generator can start at any time and

could result in death, serious injury, and unit damage.

WARNING

Risk of injury. Do not operate or service this machine

if not fully alert. Fatigue can impair the ability to service

this equipment and could result in death or serious

injury.

(000215)

WARNING

Injury and equipment damage. Do not use generator

as a step. Doing so could result in falling, damaged

parts, unsafe equipment operation, and could result

in death or serious injury.

(000216)

CAUTION

(000291)

Equipment damage. Do not attempt to start or operate

a unit in need of repair or scheduled maintenance.

Doing so could result in serious injury, death, or

equipment failure or damage.

WARNING

000406

(000103)

DANGER

Asphyxiation. Running engines produce carbon

monoxide, a colorless, odorless, poisonous gas.

Carbon monoxide, if not avoided,

will result in death or serious injury.

(000179b)

DANGER

Asphyxiation. The exhaust system must be properly

maintained. Do not alter or modify the exhaust system

as to render it unsafe or make it noncompliant with

local codes and/or standards. Failure to do so will

result in death or serious injury.

(000146)

WARNING

Equipment and property damage. Do not alter

construction of, installation, or block ventilation for

generator. Failure to do so could result in unsafe

operation or damage to the generator.

(000178a)

Asphyxiation. Always use a battery operated carbon

monoxide alarm indoors and installed according to

the manufacturer’s instructions. Failure to do so

could result in death or serious injury.

WARNING

Owner’s Manual for Portable Generator 3

• ONLY use outdoors and far away from win-

dows, doors, vents, crawl spaces and in an

area where adequate ventilation is avail-

able and will not accumulate deadly

exhaust gas.

• Using a fan or opening a door will not pro-

vide sufficient ventilation.

• Point muffler exhaust away from people

and occupied buildings.

Electrical Hazards

• The National Electric Code (NEC) requires

the frame and external electrically conduc-

tive parts of the generator be properly con-

nected to an approved earth ground. Local

electrical codes may also require proper

grounding of the generator. Consult with a

local electrician for grounding requirements

in the area.

• Use a ground fault circuit interrupter in any

damp or highly conductive area (such as

metal decking or steel work).

Fire Hazards

• Allow at least 5 feet of clearance on all

sides of the generator when operating to

prevent overheating and fire.

• Do not operate the generator if connected

electrical devices overheat, if electrical out-

put is lost, if engine or generator sparks, or

if flames or smoke are observed while unit

is running.

• Keep a fire extinguisher near the generator

at all times.

Standards Index

1. National Fire Protection Association

(NFPA) 70: The NATIONAL ELECTRIC

CODE (NEC) available from www.nfpa.org

2. National Fire Protection Association

(NFPA) 5000: BUILDING CONSTRUC-

TION AND SAFETY CODE available from

www.nfpa.org

3. International Building Code available from

www.iccsafe.org

4. Agricultural Wiring Handbook available

from www.rerc.org, Rural Electricity

Resource Council P.O. Box 309 Wilming-

ton, OH 45177-0309

5. ASAE EP-364.2 Installation and Mainte-

nance of Farm Standby Electric Power

available from www.asabe.org, American

Society of Agricultural & Biological Engi-

neers 2950 Niles Road, St. Joseph, MI

49085

This list is not all inclusive. Check with the

Authority Having Jurisdiction (AHJ) for any

local codes or standards which may be appli-

cable to your jurisdiction.

(000144)

DANGER

Electrocution. Contact with bare wires,

terminals, and connections while generator

is running will result in death or serious injury.

(000104)

DANGER

Electrocution. Water contact with a power source,

if not avoided, will result in death or serious injury.

(000145)

DANGER

Electrocution. In the event of electrical accident,

immediately shut power OFF. Use non-conductive

implements to free victim from live conductor. Apply

first aid and get medical help. Failure to do so will

result in death or serious injury.

(000130)

WARNING

Accidental Start-up. Disconnect the negative battery

cable, then the positive battery cable when working

on unit. Failure to do so could result in death

or serious injury.

(000105)

DANGER

Explosion and Fire. Fuel and vapors are extremely

flammable and explosive. Add fuel in a well

ventilated area. Keep fire and spark away. Failure to

do so will result in death or serious injury.

(000166b)

DANGER

Explosion and Fire. Do not overfill fuel tank. Fill to

1/2 inch from top of tank to allow for fuel expansion.

Overfilling may cause fuel to spill onto engine causing

fire or explosion, which will result in death or

serious injury.

(000142a)

Personal injury. Do not insert any object through the

air cooling slots. Generator can start at any time and

could result in death, serious injury, and unit damage.

WARNING

Fire risk. Fuel and vapors are extremely

flammable. Do not operate indoors. Doing so

could result in death, serious injury, or

property or equipment damage.

(000281)

WARNING

Explosion and fire risk. Do not smoke near unit.

Keep fire and spark away. Failure to do so could

result in death, serious injury, or property or

equipment damage.

(000282)

WARNING

Explosion and Fire. Do not smoke while

refueling unit. Failure to do so could result in

death, serious injury, or property or equipment

damage.

(000284a)

4 Owner’s Manual for Portable Generator

Section 2 General Information and Setup

Figure 2-1.Features and Controls

Generator Components

Figure 2-2.Control Panel

000711

000703

1 120 Volt AC, 20 Amp, GFCI Duplex

Receptacle

2 120/240 Volt AC, 30 Amp Locking

Receptacle

3 120 Volt AC, 30 Amp Locking Receptacle

4 20 Amp Circuit Breakers

5 30 Amp Circuit Breaker

6Oil Drain

7 Air Filter

8 Decompression Lever

9 Fuel Tank

10 Grounding Lug

11 Start/Run Switch

12 Muffler

13 Fuel Cap/Fuel Gauge

14 Oil Fill (2 locations)

15 Recoil Starter

16 Main 23 Amp Breaker Switch

17 Fuel Return Hose

18 Hour Meter

19 Battery (if equipped)

20 Fuel Filter

21 Engine On/Off Lever

22 Fuel On/Off

23 Voltage Selector Switch

24 Fuel Primer Bulb

000714

11 18

4 5

Owner’s Manual for Portable Generator 5

Figure 2-3.Identification Label

Know Your Generator

Replacement owner’s manuals are available

at www.drpower.com.

Emissions

The United States Environmental Protection

Agency (US EPA) (and California Air

Resources Board (CARB), for engines/equip-

ment certified to California standards) requires

that this engine/equipment complies with

exhaust and evaporative emissions stan-

dards. Locate the emissions compliance decal

on the engine to determine applicable stan-

dards. For emissions warranty information,

please reference the included emissions war-

ranty. It is important to follow the maintenance

specifications in the manual to ensure that the

engine complies with the applicable emissions

standards for the duration of the product’s life.

000705

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

Product Specifications

Generator Specifications

Rated Power Rated 5000 Watts**

Surge Power Surge Rating 5500 Watts

Rated AC Voltage 120/240

Rated AC Load

Current @ 240V

Current @ 120V

20.8 Amps**

41.7 Amps**

Rated Frequency 60 Hz @3600 RPM

Phase Single Phase

** Operating Temperature Range : -18 deg. C (0 deg. F) to 40 Deg. C (104 Deg. F). When

operated above 25 deg. C (77 deg. F) there may be a decrease in power.

** Maximum wattage and current are subject to, and limited by, such factors as fuel Btu con-

tent, ambient temperature, altitude, engine condition, etc.. Maximum power decreases about

3.5% for each 1,000 feet above sea level; and will also decrease about 1% for each 6° C (10°

F) above 16° C (60° F) ambient temperature.

5.5 / 6.5 Engine Specifications

Displacement

435 cc (26.5 in

)

Fuel Capacity 45.4 L (12 U.S. gallons)

Oil Type See chart in the Add Engine Oil section.

Oil Capacity 1.6L (1.7 qt)

Run Time at 50% Load 32 Hours

Battery Part No. 0D4575

Battery Type 12V 35Ah Battery, Group U1

* Go to www.drpower.com or call 1-855-447-3734 for replacement parts.

6 Owner’s Manual for Portable Generator

Hour Meter

The Hour Meter tracks hours of operation for

scheduled maintenance. See Figure 2-4.

• The CHG OIL display will illuminate every

100 hours. The message will flash one hour

before and one hour after each 100 hour

interval, providing a two hour window to

perform service.

• The SVC display will illuminate every 100

hours. The message will flash one hour

before and one hour after each 200 hour

interval providing a two hour window to per-

form service.

Figure 2-4.Hour Meter

When the hour meter is in flash alert mode,

the maintenance message will alternate with

elapsed time in hours and tenths. The hours

will flash four times, then alternate with the

maintenance message four times until the

meter automatically resets.

• 100 hours - CHG OIL — Oil Change Inter-

val (Every 100 hrs)

• 200 hours - SVC — Service Air Filter

(Every 200 hrs)

NOTE: The hour glass icon will flash when the

engine is running. This signifies the meter is

recording hours of operation.

Connection Plugs

120 VAC, 20 Amp, GFCI Duplex

Receptacle

The 120 Volt outlet is overload protected by a

20 Amp push-to-reset circuit breaker. See Fig-

ure 2-5. Each receptacle will power 120 Volt

AC, single phase, 60 Hz electrical loads

requiring up to 2400 watts (2.4 kW) or 20

Amps of current. Use only high quality, well-

insulated, 3-wire grounded cord sets rated for

125 Volts at 20 Amps (or greater).

NOTE: Limit length of extension cords to fif-

teen feet, or less, to prevent voltage drop and

overheating of wires.

Figure 2-5.120 VAC, 20 Amp, Duplex

Receptacle

120/240 VAC, 30 Amp Receptacle

Use a NEMA L14-30 plug with this receptacle

(rotate to lock/unlock). Connect a suitable 4-

wire grounded cord set to plug and desired

load. The cord set should be rated 250 Volts

AC at 30 Amps (or greater). See Figure 2-6.

Use this receptacle to operate 240 Volt AC, 60

Hz, single phase loads requiring up to 5000

watts (5.0 kW) of power at 20.8 Amps.

Figure 2-6.120/240 VAC, 30 Amp Receptacle

120 VAC, 30 Amp Receptacle

Use a NEMA L5-30 plug with this receptacle

(rotate to lock/unlock). Connect a suitable 3-

wire cord set to the plug and to desired load.

The cord set should be rated for 125 Volts AC

at 30 Amps (or greater). See Figure 2-7.

Use this receptacle to operate 120 Volt AC,

60Hz, single phase loads requiring up to 3600

watts (3.6kW) of power at 30 Amps. The outlet

is protected by a 30 Amp push-to-reset circuit

breaker.

Figure 2-7.120 VAC, 30 Amp Receptacle

0000.0

000205

000203

000204

000844

Owner’s Manual for Portable Generator 7

Remove Contents from Carton

1. Open carton completely by cutting each

corner from top to bottom.

2. Remove and verify carton contents prior to

assembly. Carton contents should contain

the following:

Contents

Portability Kit (optional)

3. Call Customer Service at 1-855-447-3734

with the unit model and serial number for

any missing carton contents.

4. Record model, serial number, and date of

purchase on front cover of this manual.

Assembly

Call Customer Service at 1-855-447-3734 for

any assembly issues or concerns. Please

have model and serial number available.

The following tools are required to install the

accessory kit.

• Ratchet with 10mm and 13mm sockets

• 13mm box wrenches

NOTE: The wheels are not intended for over-

the-road use.

Install wheels as follows. See Figure 2-8.

1. Insert cotter pin (E) to one end of axle (B).

2. In this order; slide washer (D), wheel (A),

washer, (D), axle mount (2-C), washer (D),

wheel (A), washer (D), and cotter pin (E)

onto axle.

3. Place wheel assembly under frame so

axle mounts align with holes in cradle

frame.

4. Secure with M6 screws (L).

Figure 2-8.Wheel Assembly

Install frame foot and rubber bumpers as

shown in Figure 2-9.

1. Slide onto M8 screw (Q), flat washer (M),

rubber foot (K).

2. Slide assembly through frame foot (J). Add

M8 flat washer (N), and secure with M8-

1.25 Locknut (P).

3. Place foot bracket assembly under cradle.

4. Slide M8 flat washers (N) onto M8-

1.25x110 screws (T) and insert through

foot bracket assembly and cradle.

5. Secure with M8 flat washer (N) and M8

locknut (P).

Item Qty.

Main Unit 1

Owner’s Manual 1

Liter Oil SAE 30 2

Product Registration Card 3

Service Warranty 1

Emissions Warranty 1

Muffler Extension 1

Battery Bracket Assembly 1

Portability Kit (optional) Qty.

10” Wheel (A) 2

Axle (B) 1

Axle Mount (C) 2

5/8” Flat Washer (D) 4

Cotter Pin (E) 2

Handle (F) 1

Handle Mount (G) 2

Handle Grip (H) 2

Frame Foot (J) 2

Rubber Feet (K) 2

M6-1x50mm Screw (L) 4

.344”x1.0” Flat Washer (M) 2

M8 Flat Washer (N) 10

M8-1.25 Locknut (P) 6

M8-1.25x30 Screw (Q) 2

M8-1.25x45 Screw (R) 2

M8-1.25x50 Screw (S) 2

M8-1.25x110 Screw (T) 2

5/16x1.25 Pin Release (U) 1

Lanyard 1

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

000704

8 Owner’s Manual for Portable Generator

Figure 2-9.Frame Foot Assembly

Install handle as shown in Figure 2-10.

1. Place a M8 flat washer (N) onto M8-

1.25x45 screw (R) and through handle

bracket and handle (A).

2. Secure with M8 flat washer (N) and M8

locknut (P).

3. Install handle grips (H).

Figure 2-10.Handle Assembly

Battery Installation (if equipped)

The following tools are required to install the

battery.

• 7/16” (11mm) ratchet, socket and wrench

Install the battery as follows. See Figure 2-11.

1. Place battery onto battery tray with the

positive terminal on the right.

2. Connect red battery wire to positive (+) ter-

minal with a bolt, washer and nut.

3. Slide red battery terminal post cover over

terminal and hardware.

4. Connect black battery wire to negative (-)

terminal with a bolt, washer and nut.

5. Slide black battery terminal post cover

over terminal and hardware.

6. Slide one spacer onto each screw.

7. Slide these assemblies through holes in

top of bracket.

8. Place bracket assembly over top of bat-

tery. Do not to touch battery terminal hard-

ware. The screws will pass through holes

on battery tray.

9. Place washer, lock washer and wing nut

onto screw.

10. Tighten wing nuts until the lock washers

are compressed to being flat.

NOTE: The battery charges while the engine

is running.

Figure 2-11.Battery Installation

Add Engine Oil

1. Place generator on a level surface.

2. Verify oil fill area is clean.

3. Remove oil fill cap and wipe dipstick clean.

See Figure 2-12.

Figure 2-12. Remove Dipstick

4. Add recommended engine oil as shown in

the following chart.

NOTE: Some units have more than one oil fill

location. It is only necessary to use one oil fill

point.

5. Thread dipstick into oil filler neck. Oil level

is checked with dipstick fully installed.

000710

000706

000716

(000135)

CAUTION

Engine damage. Verify proper type and quantity of

engine oil prior to starting engine. Failure to do so

could result in engine damage.

000115

-4 °F

(-20 °C)

14 °F

(-10 °C)

32 °F

(0 °C)

50 °F

(10 °C)

68 °F

(20 °C)

86 °F

(30 °C)

104 °F

(40 °C)

SAE 15W-40

SAE 20W

SAE 30

SAE 40

SAE 10-W30

SAE 20W

SAE 10W

000578

Owner’s Manual for Portable Generator 9

6. See Figure 2-13. Remove dipstick and ver-

ify oil level is within safe operating range.

7. Install oil fill cap/dipstick and hand-tighten.

Figure 2-13. Safe Operating Range

Fuel

IMPORTANT NOTE: DO NOT use Home

Heating Oil or Bio-Diesel Fuel.

Use No. 2D diesel fuel when temperatures are

above freezing. When temperatures are below

freezing, blend No.1D diesel fuel and No. 2D

diesel fuel together for a climate adjusted fuel

ratio.

Diesel fuel must meet the following require-

ments:

• Sulfur content of 15 parts per million (ppm)

maximum.

• Minimum Cetane index of 40.

NOTE: Low ambient temperatures as well as

engine operation at high altitudes may require

the use of fuels with higher Cetane ratings.

Fuel Maintenance

• Always treat diesel fuel for long term stor-

age. Use the approved fuel additive and

water abatement material. Test stored fuel

every 90 days and provide additional treat-

ment if required. Periodically check and dry

abatement material as necessary.

000116

(000105)

DANGER

Explosion and Fire. Fuel and vapors are

extremely flammable and explosive. Add fuel

in a well ventilated area. Keep fire and spark

away. Failure to do so will result in death

or serious injury.

(000166b)

DANGER

Explosion and Fire. Do not overfill fuel tank. Fill to

1/2 inch from top of tank to allow for fuel expansion.

Overfilling may cause fuel to spill onto engine causing

fire or explosion, which will result in death or

serious injury.

10 Owner’s Manual for Portable Generator

Section 3 Operation

Operation and Use Questions

Call Customer Service at 1-855-447-3734 with

questions or concerns about equipment oper-

ation and maintenance.

Before Starting Engine

1. Verify engine oil level is correct.

2. Verify fuel level is correct.

3. Verify battery is installed.

NOTE: The generator will not start without the

battery installed.

4. Verify unit is secure on level ground, with

proper clearance and is in a well ventilated

area.

Prepare Generator for Use

Grounding the Generator When

Used as a Portable

The generator is equipped with an equipment

ground connecting the generator frame and

the ground terminals on the AC output recep-

tacles (see NEC 250.34 (A). This allows the

generator to be used as a portable without

grounding the frame of the generator as spec-

ified in NEC 250.34. See Figure 3-1.

• Neutrals bonded to frame.

Figure 3-1. Grounding the Generator

Special Requirements

Review all Federal and State Occupational

Safety and Health Administration (OSHA) reg-

ulations, local codes, and ordinances applica-

ble to the intended use of the generator.

Additional regulations may apply if the genera-

tor is used at a construction site.

Consult a qualified electrician, electrical

inspector, or the local agency having jurisdic-

tion for additional requirements that may be

unique to your area, such as whether the gen-

erator is required to be registered with local

utility.

Connecting the Generator to a

Building Electrical System

It is recommended to use a manual transfer

switch when connecting directly to a building

electrical system. Connecting a portable gen-

erator to a building electrical system must be

made in strict compliance with all national and

local electrical codes and laws, and be com-

pleted by a qualified electrician.

Asphyxiation. Running engines produce

carbon monoxide, a colorless, odorless,

poisonous gas. Carbon monoxide, if not

avoided, will result in death or serious injury.

(000103)

DANGER

(000179b)

DANGER

Asphyxiation. The exhaust system must be properly

maintained. Do not alter or modify the exhaust system

as to render it unsafe or make it noncompliant with

local codes and/or standards. Failure to do so will

result in death or serious injury.

(000178a)

Asphyxiation. Always use a battery operated carbon

monoxide alarm indoors and installed according to

the manufacturer’s instructions. Failure to do so

could result in death or serious injury.

WARNING

(000118a)

Risk of fire. Do not use generator without

spark arrestor installed. Failure to do so

could result in death or serious injury.

(000110)

WARNING

Risk of Fire. Hot surfaces could ignite

combustibles, resulting in fire. Fire could

result in death or serious injury.

(000108)

WARNING

Hot Surfaces. When operating machine, do not

touch hot surfaces. Keep machine away from

combustibles during use. Hot surfaces could

result in severe burns or fire.

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

000707

Owner’s Manual for Portable Generator 11

Know Generator Limits

Overloading a generator can result in damage

to the generator and connected electrical

devices. Observe the following to prevent

overload:

• Add up the total wattage of all electrical

devices to be connected at one time. This

total should NOT be greater than the gener-

ator's wattage capacity.

• The rated wattage of lights can be taken

from light bulbs. The rated wattage of tools,

appliances, and motors can be found on a

data label or decal affixed to the device.

• If the appliance, tool, or motor does not

give wattage, multiply volts times ampere

rating to determine watts (volts x amps =

watts).

• Some electric motors, such as induction

types, require about three times more watts

of power for starting than for running. This

surge of power lasts only a few seconds

when starting such motors. Make sure to

allow for high starting wattage when select-

ing electrical devices to connect to the gen-

erator:

1. Figure the watts needed to start the largest

motor.

2. Add to that figure the running watts of all

other connected loads.

The Wattage Reference Guide is provided to

assist in determining how many items the gen-

erator can operate at one time.

NOTE: All figures are approximate. See data

label on appliance for wattage requirements.

Wattage Reference Guide

Transporting/Tipping of the Unit

Do not operate, store or transport the unit at

an angle greater than 15 degrees.

Device Running

Watts

*Air Conditioner (12,000 Btu) 1700

*Air Conditioner (24,000 Btu) 3800

*Air Conditioner (40,000 Btu) 6000

Battery Charger (20 Amp) 500

Belt Sander (3") 1000

Chain Saw 1200

Circular Saw (6-1/2") 800 to 1000

*Clothes Dryer (Electric) 5750

*Clothes Dryer (Gas) 700

*Clothes Washer 1150

Coffee Maker 1750

*Compressor (1 HP) 2000

*Compressor (3/4 HP) 1800

*Compressor (1/2 HP) 1400

Curling Iron 700

*Dehumidifier 650

Disc Sander (9") 1200

Edge Trimmer 500

Electric Blanket 400

Electric Nail Gun 1200

Electric Range (per element) 1500

Electric Skillet 1250

*Freezer 700

*Furnace Fan (3/5 HP) 875

*Garage Door Opener 500 to 750

Hair Dryer 1200

Hand Drill 250 to 1100

Hedge Trimmer 450

Impact Wrench 500

Iron 1200

*Jet Pump 800

Lawn Mower 1200

Light Bulb 100

Microwave Oven 700 to 1000

*Milk Cooler 1100

Oil Burner on Furnace 300

Oil Fired Space Heater (140,000

Btu)

400

Oil Fired Space Heater (85,000 Btu) 225

Oil Fired Space Heater (30,000 Btu) 150

*Paint Sprayer, Airless (1/3 HP) 600

Paint Sprayer, Airless (hand-held) 150

Radio 50 to 200

*Refrigerator 700

Slow Cooker 200

*Submersible Pump (1-1/2 HP) 2800

*Submersible Pump (1 HP) 2000

*Submersible Pump (1/2 HP) 1500

*Sump Pump 800 to 1050

*Table Saw (10") 1750 to 2000

Television 200 to 500

Toaster 1000 to 1650

Weed Trimmer 500

* Allow 3 times the listed watts for starting these

devices.

12 Owner’s Manual for Portable Generator

Starting Pull Start Engines

1. Unplug all electrical loads from the unit's

receptacles before starting engine.

2. Place generator on a level surface.

3. Turn main breaker switch OFF (A). See

Figure 3-2.

4. Turn fuel valve ON (B). See Figure 3-2.

Figure 3-2. Main Breaker Switch and

Fuel On/Off Valve

5. See Figure 3-3. Switch engine control lever

to RUN (B).

Figure 3-3. Engine Control Lever

6. See Figure 3-4. Press control panel engine

RUN/STOP switch to RUN (C).

7. Squeeze primer bulb 5-10 times until firm.

The fuel filter should show fuel level at

least half full.

8. Firmly grasp recoil handle and pull slowly

until increased resistance is felt. Flip red

decompression lever on top of engine. Pull

rapidly up and away.

– Repeat this procedure until the engine

starts. If the engine does not start

within 5 pulls, confirm steps 1-6 and

perform step 7 again.

Figure 3-4. Engine Run/Stop Switch

1. Allow engine to run for at least 10 sec-

onds, then turn main breaker ON (A). See

Figure 3-2 or Figure 3-4.

2. Select voltage rating with voltage selector

(D). See Figure 3-4.

IMPORTANT NOTE: Do not overload the

generator. Also, do not overload individual

panel receptacles. These outlets are pro-

tected against overload with push-to-reset

type circuit breakers. If amperage rating of

any circuit breaker is exceeded, that

breaker opens and electrical output to that

receptacle is lost. Read Know Generator

Limits carefully.

Starting Electric Start Engines

1. Turn main breaker switch OFF (A). See

Figure 3-2 or Figure 3-4.

2. Unplug all electrical loads from the unit's

receptacles before starting engine.

3. Place generator on a level surface.

4. Turn fuel valve ON (A). See Figure 3-2.

5. See Figure 3-3. Switch engine control lever

to RUN (B).

6. Squeeze primer bulb 5-10 times until firm.

The fuel filter should show fuel level at

least half full.

7. Press and hold the Engine Start switch (C)

until engine starts. See Figure 3-4.

Release Engine Start switch if engine

does not start within 5 seconds. If engine

does not start within 5 seconds, review

start-up procedure again before attempt-

ing start. If problems persist, refer to Trou-

bleshooting.

8. Turn Main Breaker ON.

9. Select voltage rating with Voltage Selector

(D).

(000183)

WARNING

Recoil Hazard. Recoil could retract unexpectedly.

Kickback could result in death or serious injury.

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

000708

000712

000714

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

Owner’s Manual for Portable Generator 13

Generator Shut Down

1. Turn main breaker switch OFF.

2. Switch engine start switch to OFF.

3. Turn fuel valve OFF.

Emergency Shutdown Procedure

1. Press down on small red lever on lower

engine controls (near recoil handle and

dipstick) to STOP.

2. Turn main breaker switch OFF.

3. Switch engine start switch OFF.

4. Turn fuel valve OFF.

To re-start engine, the engine control lever

must be moved to Run (B). See Figure 3-3.

Low Oil Pressure Switch

The engine is equipped with a low oil pressure

switch that shuts down the engine automati-

cally when the oil level drops below a speci-

fied level. The engine will not run until the oil

has been filled to the proper level.

If the engine shuts down and there is sufficient

fuel, check engine oil level.

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

14 Owner’s Manual for Portable Generator

Section 4 Maintenance and Troubleshooting

Maintenance

Regular maintenance will improve perfor-

mance and extend engine/equipment life.

Contact Customer Service at 1-855-447-3734,

or www.drpower.com to find a dealer for main-

tenance work to be performed. Regular main-

tenance, replacement or repair of the

emissions control devices and systems may

be performed by any repair shop or person of

the owner’s choosing. However, to obtain

emissions control warranty service free of

charge, the work must be performed by a DR

Power service dealer. See the emissions war-

ranty.

NOTE: Call 1-855-447-3734 with questions

about component replacement.

Maintenance Schedule

Follow maintenance schedule intervals,

whichever occurs first according to use.

NOTE: Adverse conditions will require more

frequent service.

NOTE: All required service and adjustments

should be each season as detailed in the fol-

lowing chart.

Preventive Maintenance

Dirt or debris can cause improper operation

and equipment damage. Clean generator

daily or before each use. Keep area around

and behind muffler free from combustible

debris. Inspect all cooling air openings on

generator.

• Use a damp cloth to wipe exterior surfaces

clean.

• Use a soft bristle brush to loosen caked on

dirt, oil, etc.

• Use a vacuum to pick up loose dirt and

debris.

• Low pressure air (not to exceed 25 psi [172

kPa]) may be used to blow away dirt.

Inspect cooling air slots and openings on

generator. These openings must be kept

clean and unobstructed.

NOTE: DO NOT use a garden hose to clean

generator. Water can enter engine fuel system

and cause problems. If water enters generator

through cooling air slots, some water will be

retained in voids and crevices of rotor and sta-

tor winding insulation. Water and dirt buildup

on generator internal windings will decrease

insulation resistance of windings.

Engine Maintenance

Engine Oil Recommendations

To maintain the product warranty, the engine

oil should be serviced in accordance with the

recommendations of this manual. For your

convenience, maintenance kits designed and

intended for use on this product are available

from the manufacturer that include engine oil,

oil filter, air filter, spark plug(s), a shop towel

and funnel. These kits can be obtained by

contacting Customer Service at 1-855-447-

3734, or www.drpower.com

At Each Use

Check engine oil level

Every Season

Check valve clearance***

Every 200 Hours or Every Season

Inspect/clean air cleaner filter**

Change oil and oil filter ǂ*

Check engine speed control

Drain fuel tank & replace outlet fuel filter

Every 1000 Hours

Check compression

Every 1500 Hours

Inspect, clean & test fuel injection nozzle

Every 2000 Hours

Check & replace fuel hoses

ǂ Change oil after first 50 hours of operation,

then every season.

* Change oil and oil filter every month when

operating under heavy load or in high tem-

peratures.

** Clean more often under dirty or dusty oper-

ating conditions. Replace air filter parts if

they cannot be adequately cleaned.

*** Check valve clearance and adjust if neces-

sary after first 50 hours of operation and

every 400 hours thereafter.

(000142a)

Personal injury. Do not insert any object through the

air cooling slots. Generator can start at any time and

could result in death, serious injury, and unit damage.

WARNING

(000135)

CAUTION

Engine damage. Verify proper type and quantity of

engine oil prior to starting engine. Failure to do so

could result in engine damage.

Owner’s Manual for Portable Generator 15

Inspecting Engine Oil Level

Inspect engine oil level prior to each use, or

every 8 hours of operation.

1. Place unit on a level surface.

2. Clean area around oil fill.

3. See Figure 4-1. Remove oil fill cap and

wipe dipstick clean.

Figure 4-1. Engine Oil Fill

4. See Figure 4-2. Screw dipstick into filler

neck. Remove dipstick and verify oil level

is within safe operating range.

Figure 4-2. Oil Level

5. Add recommended engine oil as neces-

sary. See Changing Engine Oil.

6. Replace oil fill cap and hand-tighten.

NOTE: Some units have more than one oil fill

location. It is only necessary to use one oil fill

point.

Change Engine Oil

When using generator under extreme, dirty,

dusty conditions, or in extremely hot weather,

change oil more frequently.

NOTE: Don’t pollute. Conserve resources.

Return used oil to collection centers.

Change oil while engine is still warm from run-

ning, as follows:

1. Place generator on a level surface.

2. Clean area around oil fill, and oil drain

plug.

3. Remove oil fill cap.

4. Remove oil drain plug and drain oil com-

pletely into a suitable container.

5. Install oil drain plug and tighten securely.

6. Slowly pour oil into oil fill opening until oil

level is between the crosshatch marks on

dipstick. DO NOT overfill.

7. Install oil fill cap, and finger tighten.

8. Wipe up any spilled oil.

9. Properly dispose of oil in accordance with

all applicable regulations.

Air Filter

Engine will not run properly and may be dam-

aged if run with a dirty air filter. Service air fil-

ter more frequently in dirty or dusty conditions.

To service air filter:

1. See Figure 4-3. Turn knob (A) and remove

air filter cover.

2. Wash in soapy water. Squeeze filter dry in

clean cloth (DO NOT TWIST).

3. Clean air filter cover before re-installing it.

NOTE: To order a new air filter, Customer Ser-

vice at 1-855-447-3734.

Figure 4-3. Air Filter Assembly

-4 °F

(-20 °C)

14 °F

(-10 °C)

32 °F

(0 °C)

50 °F

(10 °C)

68 °F

(20 °C)

86 °F

(30 °C)

104 °F

(40 °C)

SAE 15W-40

SAE 20W

SAE 30

SAE 40

SAE 10-W30

SAE 20W

SAE 10W

000578

(000139)

WARNING

Risk of burns. Allow engine to cool before

draining oil or coolant. Failure to do so could

result in death or serious injury.

000115

000116

(000130)

WARNING

Accidental Start-up. Disconnect the negative battery

cable, then the positive battery cable when working

on unit. Failure to do so could result in death

or serious injury.

000715

16 Owner’s Manual for Portable Generator

Battery Replacement (if

equipped)

NOTE: A battery may lose some charge when

not in use for prolonged periods of time.

The following tools are required to replace the

battery.

• 7/16” (11mm) ratchet, socket and wrench

See Figure 4-4.

1. Disconnect negative (-) battery terminal

FIRST (A).

2. Disconnect positive (+) battery terminal

SECOND (B).

3. Loosen wing nuts and remove battery

bracket and hardware.

4. Replace battery by following instructions in

the Battery Installation (if equipped) sec-

tion.

Figure 4-4. Battery Connection

Inspect Muffler and Spark Arrestor

(if equipped)

NOTE: It is a violation of California Public

Resource Code, Section 4442, to use or oper-

ate the engine on any forest-covered, brush-

covered, or grass-covered land unless the

exhaust system is equipped with a spark

arrestor, as defined in Section 4442, main-

tained in effective working order. Other states

or federal jurisdictions may have similar laws.

Contact original equipment manufacturer,

retailer, or dealer to obtain a spark arrestor

designed for exhaust system installed on this

engine.

NOTE: Use ONLY original equipment replace-

ment parts.

Inspect muffler for cracks, corrosion, or other

damage. Remove spark arrestor, if equipped,

inspect for damage or carbon blockage.

Replace parts as required.

Valve Clearance

Important: Please contact an Independent

Authorized Service Dealer for service assis-

tance. Proper valve clearance is essential for

prolonging the life of the engine.

Storage

General

It is recommended to start and run the genera-

tor for 30 minutes, every 30 days. If this is not

possible, refer to the following list to prepare

unit for storage.

• DO NOT place a storage cover on a hot

generator. Allow unit to cool to room tem-

perature before storage.

• DO NOT store fuel from one season to

another unless properly treated.

• Replace fuel container if rust is present.

Rust in fuel will cause fuel system prob-

lems.

• Cover unit with a suitable protective, mois-

ture resistant cover.

• Store unit in a clean and dry area.

• Always store generator and fuel away from

heat and ignition sources.

Prepare Fuel System for Storage

Recoil Start

1. Push and hold decompression down and

slowly pull recoil starter 2 to 3 times. Do

not start engine.

2. Pull decompression lever up. Pull recoil

slowly until resistance is felt. This will

close valves so moisture cannot enter

engine cylinder. Gently release recoil.

(000130)

WARNING

Accidental Start-up. Disconnect the negative battery

cable, then the positive battery cable when working

on unit. Failure to do so could result in death

or serious injury.

000716

(000143)

DANGER

Explosion and Fire. Fuel and vapors are extremely

flammable and explosive. Store fuel in a well

ventilated area. Keep fire and spark away. Failure

to do so will result in death or serious injury.

(000109)

WARNING

Risk of Fire. Verify machine has properly

cooled before installing cover and storing

machine. Hot surfaces could result in fire.

(000181)

WARNING

Vision Loss. Eye protection is required to avoid

spray from spark plug hole when cranking engine.

Failure to do so could result in vision loss.

Owner’s Manual for Portable Generator 17

Electric Start

1. Push and hold decompression lever down.

2. Push Start/Run/Stop switch to turn the

engine for 2 to 3 seconds. Do not start

engine.

3. Pull decompression lever up. Pull recoil

slowly until resistance is felt. This will

close valves so moisture cannot enter

engine cylinder. Gently release recoil.

4. Completely drain fuel tank or completely

fill fuel tank to proper level.

NOTE: Always treat diesel fuel for long term

storage. Use the approved fuel additive and

water abatement material. Test stored fuel

every 90 days and provide additional treat-

ment if required. Periodically check and dry

abatement material as necessary.

Change Oil

Change engine oil before storage. See

Change Engine Oil

Return Engine to Service

1. Refer to the Before Starting Engine sec-

tion.

2. Start engine and run at no load for 5 to 10

minutes while checking:

– oil pressure

– fuel, engine oil or coolant leaks

– proper operation of indicators/gauges

NOTE: Avoid prolonged operation at minimum

or maximum engine speeds and loads for the

first hour of operation.

Troubleshooting

PROBLEM CAUSE CORRECTION

Engine is running, but

AC output is not

available.

1. Circuit breaker OPEN.

2. Poor connection or defective

cord set.

3. Connected device is bad.

4. Fault in generator.

5. Main breaker switch is OFF.

6. Voltage selector switch is OFF.

7. Generator is overloaded.

8. GFCI outlet has tripped.

1. Reset circuit breaker.

2. Check and repair.

3. Connect another device that is

in good condition.

4. Contact Customer Service at

1-855-447-3734, or

www.drpower.com

5. Switch main breaker ON.

6. Switch voltage selector switch

to desired voltage output.

7. See

Know Generator Limits

8. Correct ground fault in circuit

and reset GFCI.

Engine runs well at

no-load, but bogs when

load is applied.

1. Short circuit in a connected

load.

2. Generator is overloaded.

3. Engine speed is too slow.

4. Shorted generator circuit.

1. Disconnect shorted electrical

load.

2. See

Know Generator Limits

3. Contact Customer Service at

1-855-447-3734, or

www.drpower.com

4. Contact Customer Service at

1-855-447-3734, or

www.drpower.com

18 Owner’s Manual for Portable Generator

Engine will not start; or

starts and runs rough.

1. Incorrect start sequence.

2. Fuel valve is OFF.

3. Dirty air filter.

4. Out of fuel.

5. Stale or contaminated fuel.

6. Low oil level.

7. Excessive rich fuel mixture.

8. Dirty fuel filter.

9. Air in fuel system.

10. Engine is under electrical load.

11. Battery not installed.

12. Battery weak or dead.

1. Review & follow starting pro-

cedure.

2. Turn fuel valve ON.

3. Clean or replace air filter.

4. Fill fuel tank.

5. Drain fuel tank and fill with

fresh fuel.

6. Fill crankcase to correct level.

7. Contact Customer Service at

1-855-447-3734, or

www.drpower.com

8. Replace fuel filter.

9. Repeat priming procedure. If

no start condition persists

Contact Customer Service at

1-855-447-3734, or

www.drpower.com

10. Remove all equipment from

receptacles. Make sure the

main breaker switch is OFF.

11. Install battery.

12. Charge or replace battery.

Engine shuts down

during operation.

1. Out of fuel.

2. Low oil level.

3. Fault in engine.

4. Ambient temp too high.

5. Battery weak or dead.

1. Fill fuel tank. Prime fuel sys-

tem. See

Starting Pull Start

Engines or Starting Electric

Start Engines

2. Fill crankcase to correct level.

3. Contact Customer Service at

1-855-447-3734, or

www.drpower.com

4. Move unit to cooler location

and allow engine to cool

before running again.

5. Charge or replace battery.

Engine lacks power. 1. Load is too high.

2. Dirty air filter.

3. Engine needs to be serviced.

4. Excessive valve lash.

5. Dirty fuel filter.

6. Fuel injector clogged.

7. Dirty spark arrestor.

1. Reduce load. See

Know Gen-

erator Limits

2. Clean or replace air filter.

3. Contact Customer Service at

1-855-447-3734, or

www.drpower.com

4. Contact Customer Service at

1-855-447-3734, or

www.drpower.com

5. Replace fuel filter.

6. Contact Customer Service at

1-855-447-3734, or

www.drpower.com

7. Inspect and clean spark arres-

tor.

Engine surges or

stumbles.

1. Governor/throttle assembly is

not adjusted properly.

2. Air in fuel system.

3. Battery weak or dead.

1. Contact Customer Service at

1-855-447-3734, or

www.drpower.com

2. Contact Customer Service at

1-855-447-3734, or

www.drpower.com

3. Charge or replace battery.

PROBLEM CAUSE CORRECTION

La page charge ...

DR PRO Series Le manuel du propriétaire

Marque: DR

Modèle: PRO Series

Catégorie: Groupes électrogènes

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: DR PRO Series Owner's manual
español: DR PRO Series El manual del propietario

Documents connexes

DR PRO-3500iO Le manuel du propriétaire

DR PRO Series Le manuel du propriétaire

DR PRO Series Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents