Covers Parts #8035, 8036
LED Light Kit Installation Instructions (fits #8010 bodies)
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070,
Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected]
HKC18001-R01 Rev 190405
LED Lighting Module Installation (Fig. 1) (#8035 Kit only):
1. Install the LED lighting
module (A) on the left
chassis floor pan. Secure
with the 2.5x15mm cap
screws (2).
2. Remove the screws from
the receiver box cover and
wire clamp; remove the
cover and clamp (B).
3. Remove the two 3x10mm
countersunk cap screws
from the battery tray (C).
4. Lift up the battery tray and
route the red wire (male
connector) from the LED
lighting module to the
right side of the chassis,
between the two T-Lock
servos, and through the
hole in the receiver box.
Plug the connector into
channel 1 of the receiver
(D). Note: The connector
can be plugged into any
non-telemetry channel on the TQi receiver.
5. Apply an additional bead of silicone grease (Traxxas part #1647, sold
separately) to the wire clamp. The grease will improve sealing. Reinstall the
clamp and screws.
6. Make sure the o-ring is properly seated into the groove in the receiver box so
that the cover will not pinch it or damage it in any way.
7. Install the cover and screws. Inspect the cover to make sure the o-ring seal is
not visible.
8. Reinstall the screws in the battery tray.
9. Connect the black wire (red female connector) from the LED lighting module
to the red wire (male connector) exiting the XL-5 HV electronic speed control.
Front Grille Disassembly (Fig. 6)
1. Remove the six (6) front grille retainers (E) and front grille (F) from the body.
Remove the headlight assemblies (G) from the grille (see Assembly Diagram,
Fig. 6). Retain and reuse the plastic headlight mounts and all hardware.
LED Headlight Installation (Fig. 6)
1. Install the chrome reflectors (2) onto
the circuit boards of the LED headlight
harnesses (H) (Fig. 2).
Note: The reflectors must be installed
correctly to sit flat against the circuit
boards. Align the keying features (pegs
on the reflectors with holes in the
circuit boards). Also, there is a notch
on the bottom side of the reflectors
for clearance of the wires on the
circuit boards.
2. Install the circuit boards into the
existing plastic headlight mounts (G);
then, install the new clear and orange
painted lens over the chrome reflectors
and onto the circuit boards (Fig. 3).
Note: Align the keying features (pegs
on the lens with holes in the circuit
boards and headlight mounts).
3. Install complete left and right headlight
assemblies into the front grille and secure with the 1.6x5mm button-head
screw removed during disassembly.
4. Thread the connectors and wires through the slots in the body and reinstall
the front grille and retainers using the 2.6x8mm button-head screws (6)
removed during disassembly.
5. Snap the LED side marker lights into the receptacles near each headlight.
LED Tail Light Installation
Note: The tail light LED light harnesses have a long and short wire lead. The
short wire of each harness should be installed on the left side (driver side) of the
vehicle body.
1. The rear side marker light harness has the smaller 3mm LEDs with the blue
color band near the connector. Snap the rear side marker LEDs into the side
marker light receptacles.
2. The tail light harness has the larger 5mm LEDs with the red color band near
the connector. Snap the tail light LEDs into the tail light receptacles.
Fig. 1
A
B
C
D
Visitez Traxxas.com/manuals pour télécharger
les instructions dans votre langue.
Visite la página Traxxas.com/manuals para
descargar el instrucciones en su idioma.
Auf Traxxas.com/manuals, können Sie
anleitung in Ihrer Sprache downloaden.
Fig. 2
Fig. 3
2.6x8 BCS
2.6x8 BCS
2.6x8 BCS
1.6x5 BCS
1.6x5 BCS
2.6x8 BCS
E
F
G
E
Assembly Diagram Fig. 6
G
H
H
F
E
E
E
E
J
I
#8035 Kit Contents:
• LED lighting module
• Distribution block
• Distribution block mount
• Left headlight harness assembly
• Right headlight harness assembly
• Rear marker light harness
• Rear tail light harness
• Jumper
• Extension harness (for use with
optional accessories)
• Headlight lens (2)
• Headlight reflector (2)
• 2.6x8mm button-head screws (2)
• 2.5x15mm cap screws (2)
• Zip ties (10)
#8036 Kit Contents:
• Distribution block
• Distribution block mount
• Left headlight harness assembly
• Right headlight harness assembly
• Rear marker light harness
• Rear tail light harness
• Jumper
• Extension harness (for use with
optional accessories)
• Headlight lens (2)
• Headlight reflector (2)
• 2.6x8mm button-head screws (2)
• Zip ties (10)
• 2.0mm hex wrench
• 1.5mm hex wrench
• Side cutters (to trim zip ties)
Tools required:
YELLOW*
GREEN (Jumper)
Headlight and Front Side Marker Light Wiring
Tail Light Wiring
Rear Side Marker Light Wiring
FRONT
BOTTOM VIEW
To LED
Lighting Module
DISTRIBUTION BLOCK
DISTRIBUTION BLOCK PORTS
BLUE (Rear Side
Marker Light Wiring)
RED (Tail Light
Wiring)
WHITE (Headlight &
Front Side Marker
Light Wiring)
*For use with optional accessories.
Not used with this LED light kit.
Wiring Diagram
Wire Routing (Fig. 7)
When installing the LED light harnesses, note where the installation begins and ends in the Wiring
Diagram (Fig. 7). Use zip ties to secure the wiring to the body in the locations provided. The zip ties do
not need to be tight; allow some slack for wire movement.
Distribution Block Installation
1. Remove the 2.6x8mm button-head screws (2) from the side trim retainer. Install the distribution
block mount (I) and secure with the 2.6x8 mm button-head screws (2) as shown in Fig. 4.
2. Plug the connectors from the LED light wire harnesses into the ports of the distribution block (J).
Match the color band on the wire harnesses with the corresponding color of each port indicator on
the distribution block (white for headlights, red for tail lights, blue for rear side marker lights).
3. Plug the included jumper into the green port of the distribution block as indicated (see Wiring
Diagram, Fig. 7). Note: The jumper will allow the LED lights to go into full power (high beam) mode.
The jumper is not required for the LED lights to function (the lights will remain in low power (low
beam) mode if the jumper is not used). Also, a compatible roof LED lightbar accessory (part #8025)
is available separately that will provide this same high beam/low beam option once it is connected
to the yellow and green ports on the distribution block (requires use of the supplied extension
harness).
4. Use the included 2.6x8mm button-head screws to secure the distribution block to the mount.
Fig. 4
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070,
Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected]
Fig. 7
-
1
-
2
dans d''autres langues
Documents connexes
-
Traxxas TRX-4 Bronco Mode d'emploi
-
Traxxas TRX-4 Blazer Mode d'emploi
-
Traxxas TRX-4 G 500 4X4² Mode d'emploi
-
-
-
-
-
Traxxas Hoss 4X4 VXL Mode d'emploi
-
-