Faber CAPR48SS1200 Guide d'installation

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

Instrucciones de instalación

Información de uso y cuidado

CAMINO PRO

CAPR36SS600

CAPR36SS1200

CAPR48SS1200

2

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START

INSTALLING THIS RANGEHOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium setting.

b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan

orlter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A

RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnofftheburner.

BECAREFULTOPREVENTBURNS.IftheamesdonotgooutimmediatelyEVACUATE

AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will

result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. Thereissmallandcontainedintheareawhereitstarted.

3. Theredepartmentisbeingcalled.

4. Youcanghttherewithyourbacktoanexit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this

fan with any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any

questions, contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the

service disconnecting means to prevent power from being switched on acciden-

tally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or

Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccor-

dance With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sufcientairisneededforpropercombustionandexhaustingofgasesthrough

theue(chimney)offuelburningequipmenttopreventbackdrafting.Followthe

heating equipment manufacturer's guideline and safety standards such as those

publishedbytheNational FireProtectionAssociation(NFPA),andtheAmerican

SocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE),and

the local code authorities.

3

ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST

BE SEALED.

This rangehood requires at least 24" of clearance between the bottom of the rangehood

and the cooking surface or countertop. This hood has been approved by UL at this distance

from the cooktop.

This minimum clearance may be higher depending on local building codes. For gas cooktops

and combination ranges, a minimum of 30" is recommended and may be required.

Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking surface

or countertop. Consult the cooktop or range installation instructions given by the manufacturer

before making any cutouts.

MOBILE HOME INSTALLATION The installation of this rangehood must conform to the

Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly

Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See

Electrical Requirements.

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

!

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the

wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efcient

performance. The size of the ductwork should be uniform. Do not install two elbows together. Use

duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor opening

around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence

that greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts.

Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting

frame must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Do

not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

4. Ducted fans must always be vented to the outdoors.

4

• Electrical ground is required on this rangehood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO

NOT use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or

grounding circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the rangehood is

properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

!

StateofCaliforniaProposition65Warning(USonly)

WARNING

This product contains chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

Note: The hood needs to be installed on a separate electrical circuit.

5

1 MOTOR - RANGEHOOD DIMENSIONS 36"

DRAFT 28-NOV-2018 17:42

1 MOTOR RANGEHOOD REAR VENTING

6

2 MOTOR - RANGEHOOD DIMENSIONS 36"

9 13/16”

11 7/16”

11 1/16”

4 15/16”

10" DUCT TRANSITION FOR 2 MOTOR RANGEHOOD 36"

DRAFT 28-NOV-2018 15:53

7

2 MOTOR - RANGEHOOD DIMENSIONS 48"

DRAFT 28-NOV-2018 16:20

9 13/16”

11 7/16”

11 1/16”

4 15/16”

10" DUCT TRANSITION FOR 2 MOTOR RANGEHOOD 48"

8

7

6

9e

8

7

6

9e

8

MAIN PARTS 1 MOTOR RANGEHOOD 36"

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with: Controls, Light

6 3 Greaselters

7 6 Filter knobs

8 1 Grease rail

9 1 Recirculation Vent Grill

10 1 Damper ø 5 7/8"

11 1 Blower

Ref. Qty. Installation Components

12a 2 Wall plug

12b 4 Screws 3/16"x1 15/16"

12c 6 Greaseltersscrews(3/16"x3/8")

12e 2 Motorxscrews(3/16"x3/8")

12f 2 Screws 1/8"x 3/8"

  (forRecirculationVentGrillmounting)

Qty. Documentation

1 Instruction Manual

MAIN PARTS 2 MOTOR RANGEHOOD 36"

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with: Con trols, Light

2 1 Duct transition

6 3 Greaselters

7 6 Filter knobs

8 1 Grease rail

9 1 Recirculation Vent Grill

10 2 Damper ø 5 7/8"

11 2 Blower

Ref. Qty. Installation Components

12a 2 Wall plug

12b 4 Screws 3/16"x1 15/16"

12c 6 Greaseltersscrews(5/32"x5/16")

12d 4 screws 1/8"x1/4"

12e 4 Motorxscrews(3/16"x3/8")

12f 2 Screws 1/8"x 3/8"

  (forRecirculationVentGrillmounting)

Qty. Documentation

1 Instruction Manual

1

12a

12b

7

6

9e

8

12a

12b

10

1

2

12c

12d

12e

9

12f

9

12f

11

9

7

6

9e

8

MAIN PARTS 2 MOTOR RANGEHOOD 48"

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with: Controls, Light

2 1 Duct transition

6 4 Greaselters

7 8 Filter knobs

8 1 Grease rail

9 1 Recirculation Vent Grill

10 2 Damper ø 5 7/8"

11 2 Blower

Ref. Qty. Installation Components

12a 2 Wall plug

12b 4 Screws 3/16"x1 15/16"

12c 8 Greaseltersscrews(5/32"x5/16")

12d 4 screws 1/8"x1/4"

12e 4 Motorxscrews(3/16"x3/8")

12f 2 Screws 1/8"x 3/8"

  (forRecirculationVentGrillmounting)

Qty. Documentation

1 Instruction Manual

7

6

9e

8

12a

12b

10

1

2

12c

12d

7

6

9e

8

12e

7

6

9e

8

9

12f

11

10

AVAILABLE ACCESSORIES

PARTS NEEDED

6" Round Metal Ductwork

Telescopic Chimney Duct Cover:

- sku#: CHIM3448 (Use with 48" Camino Pro)

- sku#: CHIM2224 (Use with 36" Camino Pro)

- sku#: CHIM2248 (Use with 36" Camino Pro)

- sku#: CHIM3424 (Use with 48" Camino Pro)

CFM Reducer Accessory Kit sku#: CFMRED

CFM Reducer Accessory Kit sku#: CFMRED-2

Activated Charcoal Filter sku #: FILTER1

Charcoal Filter Kit Washable Long Lasting sku#: FILTER1LL

Min. 24" Min. 30"

11

6"

Rear

1 MOTOR RANGEHOOD REAR INFORMATION





Only for the rst installation

For a rear ducting installation

the blower bracket needs to be

unsecured by rst removing the 12

screws as shown.

Once the screws are removed,

extract it from the body of the Hood

and position it so the transition

opening is facing to the rear wall

(from the back remove and rotate

180 degrees to the left, and then ip

it back 90 degrees as shown in the

diagram).

Once the blower bracket is in place

reinstall the 12 screws to fasten the

bracket to the Hood body.

1





1 MOTOR RANGEHOOD REAR DUCTED INSTALLATION

180°

90°

12

Install the motor into the upper of the hood using

the 2 screws 12e supplied.

Put the motor in the hood body.

2 3

4

9 hole end

Connect the wire cable 9 hole end to the

motor.

180°

90°

13

1 MOTOR RANGEHOOD TOP DUCTED INSTALLATION

1 2

Install the motor into the rear of the hood using

the 2 screws 12e supplied.

Put the motor in the hood body.

3

9 hole end

Connect the wire cable 9 hole end to the

motor.

14

Install the 2 motors into the sides of the blower bracket using the 4 screws 12e supplied.

Put the 2 motors in the hood body. Inside the hood there is a blower bracket divider and the

motors will be one a side.

1

2

Version 07/11 - Page 9

INSTALLATION WITH IB1200 INTERNAL BLOWER (1200 cfm)

1. Install the Plate B (FIGURE 14) which came with the internal

blower kit, on top of the rangehood with the holes located closer to

the front. Use 9 screws supplied with the blower kit

2. Remove the white plastic covering and Install the 4 side trim

pieces to the outside of the hood using (16) part 9b screws, see

the side rail installation in (FIGURE 15).

3. Attach the blower bracket divider inside the hood, with the 2

screws into the top of the hood and 2 screws into the back, all

supplied with the blower kit (FIGURE 16)

FIGURE 16

FIGURE 17

4. Install the 2 motor kits into the sides of the blower bracket using

the 4 screws supplied with the motor kit. (FIGURE 17)

5. Connect the wire (FIGURE 18) that comes with the motor kit

from the side of the two motors to the connection on the inside

of the light panel in the hood. The two - 9 hole ends of the wire

are installed in the two motors, the 6 hole end is connected to

the light panel (FIGURE 11 on the previous page)

FIGURE 15

FIGURE 18

FIGURE 19

6. Install the 2 dampers on top of the hood. If you want one 10"

round duct to come out of the top of the hood, use the transition

piece (FIGURE 19) that comes with the motor kit and install with

four screws. If you want to use 2 seperate 6" round ducts, do not

use the transition.

7. Attach the hood to the cabinet using (12) 9c. screws to the

cabinet. FIGURE 20

8. Follow steps 6 - 9 on the previous page to connect ducting,

wiring, and test the electrical connection.

FIGURE 14

FIGURE 20

B

Version 07/11 - Page 9

INSTALLATION WITH IB1200 INTERNAL BLOWER (1200 cfm)

1. Install the Plate B (FIGURE 14) which came with the internal

blower kit, on top of the rangehood with the holes located closer to

the front. Use 9 screws supplied with the blower kit

2. Remove the white plastic covering and Install the 4 side trim

pieces to the outside of the hood using (16) part 9b screws, see

the side rail installation in (FIGURE 15).

3. Attach the blower bracket divider inside the hood, with the 2

screws into the top of the hood and 2 screws into the back, all

supplied with the blower kit (FIGURE 16)

FIGURE 16

FIGURE 17

4. Install the 2 motor kits into the sides of the blower bracket using

the 4 screws supplied with the motor kit. (FIGURE 17)

5. Connect the wire (FIGURE 18) that comes with the motor kit

from the side of the two motors to the connection on the inside

of the light panel in the hood. The two - 9 hole ends of the wire

are installed in the two motors, the 6 hole end is connected to

the light panel (FIGURE 11 on the previous page)

FIGURE 15

FIGURE 18

FIGURE 19

6. Install the 2 dampers on top of the hood. If you want one 10"

round duct to come out of the top of the hood, use the transition

piece (FIGURE 19) that comes with the motor kit and install with

four screws. If you want to use 2 seperate 6" round ducts, do not

use the transition.

7. Attach the hood to the cabinet using (12) 9c. screws to the

cabinet. FIGURE 20

8. Follow steps 6 - 9 on the previous page to connect ducting,

wiring, and test the electrical connection.

FIGURE 14

FIGURE 20

B

3

9 hole end

Connect the wire cable 9 hole end to the

left motor and the other wire cable 9 hole

end to the right motor.

9 hole end

2 MOTOR RANGEHOOD TOP DUCTED INSTALLATION

15

Install Damper that is included with the

Hood before connecting to the ductwork.

One for 1 motor model.

Two for 2 motor model.







H

I









H

I









H

I



INSTALLATION INSTRUCTIONS

==

Installation Instruction for Mounting on the Wall

Draw a vertical line on the supporting wall as high as practical, at the center of the area in which

the hood will be installed.

Draw a horizontal line at where the bottom edge of the hood will be located as indicated in the

gure that is a minimum of 24" or 30" above cooking surface.

1

Min. 24" Min. 30"

16

Ø 1/2”

x2

24”

L

16 1/2”

30”

L = 19 11/16”

36”

Ø 1/2”

x2

24”

L

16 1/2”

30”

36” - 48”

L = 19 11/16”

36”

L = 31 1/8”

48”

2.a

Mark the wall where indicated, 16 1/2" above the horizontal line and at L distance on the left and right

of vertical line. The distance L changes for all dimension of Hood.

Insert the two wall plugs 12a in the holes as shown and x them.

Installation for 1 Motor Rangehood

For a different type of Wall, it's

possible to use only the bracket by

remove the plug and the screw from

the plug 12a.

Combine the bracket with specic

wall plug or screw.

17

Ø 1/2”

x2

24”

L

16 1/2”

30”

L = 19 11/16”

36”

Ø 1/2”

x2

24”

L

16 1/2”

30”

36” - 48”

L = 19 11/16”

36”

L = 31 1/8”

48”

2.b

Installation for 2 Motor Rangehood

Mark the wall where indicated, 16 1/2" above the horizontal line and at L distance on the left and right

of vertical line. The distance L changes for all dimension of Hood.

Insert the two wall plugs 12a in the holes as shown and x them.

For a different type of Wall, it's

possible to use only the bracket by

remove the plug and the screw from

the plug 12a.

Combine the bracket with specic

wall plug or screw.

18

Ø 5/16”

x4

Hook the hood body onto the wall plugs 12a. Use a level to insure that Fixing Bracket is level

by adjusting the screws as shown in the picture.

Mark the wall where indicated.

Drill directly into ø 5/16" holes at all the center points marked.

Insert the purchased wall plugs in the holes.

Using thhe remaining screws to anchor the hood in holes.

If installation uses the telescopic chimney extension, refer to the installation manual included in

the Chimney Kit (CHIM3448 - CHIM2224 - CHIM2248 - CHIM3424)

11b

3

4

5

19

1 AND 2 MOTORS DUCTING METHODS 6"

Install Roof or Wall Cap purchased separately. Connect the 6" metal ductwork to the Roof or Wall Cap and

then attach ductwork.

1 AND 2 MOTORS STANDARD DUCTING METHODS

Vertical

Horizontal

Rear

(Validfor1

motor range-

hood only)

20

2 MOTORS DUCTING METHODS 10"

Install Roof or Wall Cap purchased separately. Connect the 10" metal ductwork to the Roof or Wall Cap

and then attach ductwork.

Fix the Duct transition in the hood body with

4 screws 12d.

La page charge ...

Faber CAPR48SS1200 Guide d'installation

Ce manuel convient également à

Faber CAPR48SS1200 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents