Faber OSTR30SS400 Le manuel du propriétaire

OSTR30SS400

OSTR36SS400

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

OSTRO

2

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START

INSTALLING THIS RANGEHOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium setting.

b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan

orlter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A

RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnofftheburner.

BECAREFULTOPREVENTBURNS.IftheamesdonotgooutimmediatelyEVACUATE

AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will

result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. Thereissmallandcontainedintheareawhereitstarted.

3. Theredepartmentisbeingcalled.

4. Youcanghttherewithyourbacktoanexit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this

fan with any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any

questions, contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the

service disconnecting means to prevent power from being switched on acciden-

tally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or

Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccor-

dance With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sufcientairisneededforpropercombustionandexhaustingofgasesthrough

theue(chimney)offuelburningequipmenttopreventbackdrafting.Followthe

heating equipment manufacturer's guideline and safety standards such as those

publishedbytheNational FireProtectionAssociation(NFPA),andtheAmerican

SocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE),and

the local code authorities.

3

ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST

BE SEALED.

This rangehood requires at least 24" of clearance between the bottom of the rangehood

and the cooking surface or countertop. This hood has been approved by UL at this distance

from the cooktop.

This minimum clearance may be higher depending on local building codes. For gas cooktops

and combination ranges, a minimum of 30" is recommended and may be required.

Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking surface

or countertop. Consult the cooktop or range installation instructions given by the manufacturer

before making any cutouts.

MOBILE HOME INSTALLATION The installation of this rangehood must conform to the

Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly

Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See

Electrical Requirements.

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

!

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the

wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efcient

performance. The size of the ductwork should be uniform. Do not install two elbows together. Use

duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor opening

around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence

that greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts.

Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting

frame must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Do

not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

4. Ducted fans must always be vented to the outdoors.

4

• Electrical ground is required on this rangehood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO

NOT use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or

grounding circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the rangehood is

properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

!

StateofCaliforniaProposition65Warning(USonly)

WARNING

This product contains chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

5

RANGEHOOD DIMENSIONS

RANGEHOOD DIMENSIONS WITH OPTIONAL FULL CHIMNEY

RANGEHOOD DIMENSIONS WITH OPTIONAL TELESCOPIC CHIMNEY

29

15/16

” - 35

3/4

”

29

15/16

” - 35

3/4

”

29

15/16

” - 35

3/4

”

6

MAIN PARTS

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with: Con-

trols, Light, Filters, Blower.

8 1 Recirculation Vent Grill

10 1 Damper ø 5 7/8"

Ref. Qty. Installation Components

11b 2 Wall Plug

12a 4 Screw 3/16" x 1 3/4"

13 4 Washers

14 6 Screws 3/16" x 1 15/16"

12e 2 Screws 1/8"x 3/8"

(for Recirculation Vent

Grill mounting)

Qty. Documentation

1 Instruction Manual

Available Accessories

Parts needed

- 6" Round Metal ductwork .

Direct Connect Wiring Box sku # number: WIREBOX

30" Full Width Chimney Duct Cover - sku#FULL30

36" Full Width Chimney Duct Cover - sku#FULL36

Telescopic Chimney Duct Cover - TELEMAES

CFM Reducer Accessory Kit - CFMRED2

Activated Charcoal Filter sku #; FILTER1

Activated Charcoal Filter sku #; FILTER1LL

30" Recirculation Kit - DUCTGRT30"

36" Recirculation Kit - DUCTGRT36"

Created by

-

Denomination

-

Lang EN

Sheet

1

/1

Modif.by

Approved by

Approval date

Doc. status

Drawing N.

NEW_DRAWING_BOX

Rev

01

10

1

12a

14

13

11b

6

MAIN PARTS

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with:

Controls, Light, Filters,

Blower.

2 2 Bracket

3 2 Cover

8 1 Recirculation Vent Grill

10 1 Damper ø 5 7/8"

1 Remote Control REMCTRL

Ref. Qty. Installation Components

12a 4 Screws 1/8" x 5/8"

12e 2 Screws 1/8"x 3/8"

(for Recirculation Vent

Grill mounting)

Qty. Documentation

1 Instruction Manual

2

12a

3

1





H

Available Accessories

Parts needed

- 6" Round Metal ductwork.

Direct Connect Wiring Box sku # number: WIREBOX

Make-Up Air Dampers:

6" Make-Up Air Damper Kit MUDAMPER6

8" Make-Up Air Damper Kit MUDAMPER8

Standard Liner 30- LINE30ST

Standard Liner 36 - LINE36ST

Activated Charcoal Filter sku #; FILTER1

CFM Reducer Kit #CFMRED

7

Min.24" Min.30"







H

I



Install Damper that is included with the

Hood before connecting to the ductwork.

Use 2 hands to remove ﬁlters.

Turn the knob to the left (coun-

terclockwise) to release ﬁlter.

Repeat with other ﬁlter. Reinstall

the ﬁlter by placing the back

edge in the channel at rear of

hood. Push ﬁlter into place, turn

the knob to the right (clockwise)

to attach to range hood. Repeat

with other ﬁlter.

BafeFilterRemoval

Removal / Déplacement

Removal

8

Ducted Venting Options Installation

Horizontal

Vertical

6"

Rear

6"

Ducting Methods

9

Rear Ducted Installation





The Electrical Connector must be

removed ﬁrst before converting the

hood to Rear Ducting mode.

For a horizontal ducting installation

the motor needs to be unsecured

by ﬁrst removing the 12 screws as

shown.

Once the screws are removed,

extract the blower from the body

of the Hood and position it so the

transition opening is facing to the

rear wall (from the back remove and

rotate 180 degrees to the left, and

then ip it back 90 degrees as shown

in the diagram).

Once the blower is in place re-install

the 12 screws to fasten the motor to

the Hood body.

Disconnect the Electrical Connector

by depressing the tabs with your

hand and also using light force on

one tab with a at head screwdriver.

Reconnect the Connector to the

blower.

10

RECIRCULATION INSTRUCTIONS

RECIRCULATING INSTALLATIONS

For recirculating installations, Charcoal Filters are necessary. Remove all grease ﬁlters

and set aside. Attach one charcoal ﬁlter to each end of the blower. Each charcoal ﬁlter

attaches to the grid on the side of the blower. Rotate the ﬁlter clockwise to install and

counterclockwise to remove (FIGURE 3C). Replace all grease ﬁlters.

There are 2 ways to recirculate the Ostro:

1) Use the Ductless Recirculating Kit (sold separately), refer to installation instructions

inside the Recirculating Kit which includes charcoal ﬁlters.

DUCTGRT30" - (30")

DUCTGRT36" - (36")

2) Duct work must be installed to exhaust the rangehood back into the kitchen, either at

the top of the cabinet (FIGURE 3A) or at the face or side of the sofﬁt (FIGURE 3B). Install

at least 15" of metal duct (ﬁg.3A and 3B) at the air exit. Run the duct vertically and se-

cure it at the opening cut out at the top or side of the cabinet or sofﬁt. Installation of metal

grill is recommended. This duct work must not terminate into a dead air space. FILTER1

must be purchased to complete this type of installation.

This page needs to be inserted

after Page 9 and before Page 10

Add the new

kit

:DUCTGRT42

–(42“)

This page needs to be inserted

after Page 9 and before Page 10

Add the new

kit

:DUCTGRT42

–(42“)

Note: It is recommended that pro-

fessional style cooking always be

vented to the outside; for recirculat-

ing Installations, some duct work is

required to exhaust the unit out of

the cabinet.

11

Installation for Mounting on the Wall

==

Installation Instruction for mounting on the Wall

Draw a vertical line on the supporting wall

as high as practical, at the center of the

area in which the hood will be installed.

Draw a horizontal line at where the bottom

edge of the hood will be located as indicated

in the ﬁgure that is a minimum of 24"- 30"

above cooking surface

1

Min.24" Min.30"

12

2

´

[

24” - 30”

L

/ ´´



7 13/16”

Mark the wall where indicated, 7 13/16" above the horizontal line and at L distance on the left and

right of vertical line. The distance L change for all dimension of Hood.

Insert the two wall plugs in the holes as shown and ﬁx.

3

4

E

Hook the hood body onto the wall plugs.

Use a level to insure that Fixing Bracket is

level and then fully secure the two screws.

13

5

´

[

Mark the wall where indicated.

Drill directly into ø 5/16" holes at all the center points marked.

Insert the purchased wall plugs in the holes.

Using two remaining screws to anchor the hood in holes.

If your installation uses the optional duct cover, ﬁt the cover anges over the brackets. If

installation uses the telescopic chimney extension, ﬁt the extension over the brackets. Install the

upper section ﬁrst, then ﬁt the lower section over the upper section. Seal extension to hood with

clamps.

12a + 13

14

Installation Instruction for Mounting Under the Cabinet

[

Lift the hood to the cabinet.

Fix the Hood Body with 4 screws from

the bottom.

Mark the wall where indicated.

Drill directly into ø 5/16" holes at all the center

points marked.

Insert the purchased wall plugs in the holes.

Using two remaining screws to anchor the hood

in holes.

1

´

[

3

4

12a + 13

[

2

6 x 14

Non Ducted - Recirculation Option

For Non-Ducted Recirculation venting route the

ductwork to a location above the hood where the

discharge is vented back into the room.

Use the included Recirculation Vent Grill (8) to

cover the opening. Secure the grill with the 2 screws

(12e) provided in the Install Kit.





´

8

12e

15

INSTALLATION CONTINUED

Optional Duct Cover Installation

1. Attach the full-width duct cover to the top of the range hood

with the screws provided. The duct cover must be attached

to the top of the range hood before mounting the range hood

to the wall.

A: Distance from center of mounting bracket to centerline:

30" hood: 13 15/32" / 36" hood: 16 15/32" /

42" hood: 19 15/32" / 48" hood: 22 15/32"

B: Mounting brackets

C: Top of hood

2. Install each bracket on the wall as shown. Make sure the

screws and brackets are securely fastened to the wall.

IMPORTANT: Install only the brackets. Do not install the

hood.

Optional Telescopic Chimney Extension Installation

1. If a chimney extension is used, attach the extension brackets

as shown. Make sure that the screws are securely fastened to

the wall.

A: Ceiling

B: Brackets

C. Top of hood

INSTALLATION CONTINUED

1. Attach the full-width duct cover to the top of the range hood with the screws provided. The duct

cover must be attached to the top of the range hood before mounting the range hood to the wall.

A: Distance from center of mounting bracket to centerline:

30" hood: 13 15/32"

36" hood: 16 15/32"

42" hood: 19 15/32"

B: Mounting brackets

C: Top of hood

2. Install each bracket on the wall as shown. Make sure the screws and brackets are securely

fastened to the wall. IMPORTANT: Install only the brackets. Do not install the hood.

Optional Duct Cover Installation

INSTALLATION CONTINUED

Optional Duct Cover Installation

1. Attach the full-width duct cover to the top of the range hood

with the screws provided. The duct cover must be attached

to the top of the range hood before mounting the range hood

to the wall.

A: Distance from center of mounting bracket to centerline:

30" hood: 13 15/32" / 36" hood: 16 15/32" /

42" hood: 19 15/32" / 48" hood: 22 15/32"

B: Mounting brackets

C: Top of hood

2. Install each bracket on the wall as shown. Make sure the

screws and brackets are securely fastened to the wall.

IMPORTANT: Install only the brackets. Do not install the

hood.

Optional Telescopic Chimney Extension Installation

1. If a chimney extension is used, attach the extension brackets

as shown. Make sure that the screws are securely fastened to

the wall.

A: Ceiling

B: Brackets

C. Top of hood

Optional Telescopic Chimney Extension Installation

1. If a chimney extension is used, attach the extension brackets as shown. Make sure that the

screws are securely fastened to the wall.

A: Ceiling

B: Brackets

C: Top of hood

16

Direct Connect Wiring Box

Accessory sku # WIREBOX

(purchased separately)

Created by

-

Denomination

-

Lang EN

Sheet

1

/1

Modif.by

Approved by

Approval date

Doc. status

Drawing N.

NEW_DRAWING_BOX

Rev

01

ELECTRICAL INSTALLATION WITH CONNECTION CABLE

ELECTRICAL INSTALLATION WITH

OPTIONAL WIRING BOX

For Permanent wiring Installation-Use only

with Listed rangehood Wiring Box kit

sku # WIREBOX, manufactured by Faber.

Max. 33 7/16”

GROUNDING INSTRUCTIONS This appliance must

be grounded. In the event of an electrical short circuit,

grounding reduces the risk of electric shock by providing

an escape wire for the electric current. This appliance

is equipped with a cord having a grounding wire with a

grounding plug. The plug must be plugged into an outlet

that is properly installed and grounded.

WARNING - Improper grounding can result in a risk of

electric shock.

Consult a qualiﬁed electrician if the grounding instructions

are not completely understood, or if doubt exists as to

whether the appliance is properly grounded.

Do not use an extension cord. If the power supply cord

is too short, have a qualiﬁed electrician install an outlet

near the appliance.

The supply cord shall be accessible for inspection after

installation.

Replace the ﬁlters removed previously.

17

USE AND CARE INFORMATION

,

LED indicator light (I) - indicates current speed with color

Green - speed 1

Orange - speed 2

Red - speed 3

Flashing Red - intensive speed

Light On/Off Button ( L )

On/Off switch for the halogen lights. Press the button to turn the light ON and press again

to turn it OFF.

Blower On/Off Button ( T1 )

On/Off button for the blower. Press the button to turn the blower ON to speed one (indi-

cated by green LED) and press again to turn the hood off

Blower Speed 2 (T2)

Press this button to turn the hood onto speed #2. (indicated by orange LED)

Blower Speed 3 / Intensive (T3)

Press this button to turn the hood onto speed #3. (indicated by solid red LED) Hold down

the speed 3 button for 2 seconds to activate the intensive speed. The intensive speed set-

ting is indicated by a blinking red light. This operates the hood for 6 minutes on the highest

speed and then returns to the previous speed.

For Best Results

Start the rangehood several minutes before cooking to develop proper airow. Allow the

unit to operate for several minutes after cooking is complete to clear all smoke and odors

from the kitchen.

18

Cleaningbafegreaselters

The lters must be cleaned every 2 months of operation,

or more frequently for particularly heavy usage, and can

be washed in a dishwasher.

The metal grease lters should be cleaned frequently

in hot detergent solution or washed in the dishwasher.

Stainless steel cleaner should be used on stainless

rangehoods. Abrasives and scouring agents can scratch

stainless steel nishes and should not be used to clean

nished surface. Remove all water or any other liquid

from washing before re-installing lters.

Replacingactivatedcharcoallter

The lter is not washable and cannot be regenerated,

and must be replaced approximately every 4 months of

operation, or more frequently for particularly heavy usage.

• Remove the Filters one at a time, pushing them

towards the back of the unit and at the same time

pulling downward.

• Remove the saturated charcoal lter by releasing

the xing hooks.

• Fit the new lter and fasten it in its correct position.

• Replace, taking care to ensure that the handle faces

forwards.

• CAUTION : When used in recirculation mode, to

Reduce the Risk of Fire and Shock use only conver-

sion kit Model FILTER 1 or kit Model FILTER 1LL.





Lighting unit

• Remove the snap-on lamp cover by levering it from

under the metal ring, supporting it with one hand.

• Replace the lamp with a new one of the same type,

making sure that you insert the two pins properly into

the housings on the lamp holder.

• Replace the snap-on lamp cover.

19

Wiring Diagram

0 1 2 3 4 5 6 7 8 9

H90_021

02

Drawing N : Rev :

Modif. by

Doc.status

Do not get quotas from the drawing do not bring

modifications without authorization of techincal office.

According to the law we reserve the own of the present

drawing with reproduction prohibition partial or total.

Approved date

Modification description

Approved by

SCHEMA ELETTRICO M8-4V ESZ

Doc Type

Denomination

Creation date

16.Feb.2018

CORRADO DOLCE

Created by

991.0349.116

Code

220-240V ~50Hz

220~60Hz

110-127V 60Hz

F N

BLU

PNK

BRW

WHT

1

2

3

4

5

6

BLK

Y-G

123

654

987

PNK

M8-4V

BRW

ORG

M1

V1

MC

F

V2

ESZ

BRWWHT

L-BBLU

BLK

GRY

BLK

GRY

123

654

789

0-1

MOTOR

L-B

BRW

1

BRW

L-B

2

L-B

BLK

3

BLK

GRY

4

GRY

2

SPEED

BLU

5

BLU

PNK

6

PNK

WHT

7

WHT

VLT(org)

8

VLT(org)

RED(org)

9

RED(org)

10

3/I

SPEED

11

12

HALOGEN

LAMPS

0-1

LIGHT

N

L

V4

L

V3

PRI.SEC.

ELECTRONIC

TRNSFORMER

WHT

1

2

3

4

5

6

L-B

BLK

GRY

RED(ORG)

VLT(ORG)

RED

VLT

INCANDESCENT/HALOGEN

LAMP

RED

20

January 4, 2016

FABER CONSUMER WARRANTY & SERVICE

All Faber products are warranted against any defect in materials or workmanship for the original purchaser

for a period of 1 year from the date of original purchase (requires proof of purchase). This warranty covers

labor and replacement parts. Faber, at its option, may repair or replace the product or components

necessary to restore the product to good working condition. To obtain warranty service, contact the dealer

from whom you purchased the range hood, or the local Faber distributor. If you cannot identify a local Faber

distributor, contact us at (508) 358-5353 for the name of a distributor in your area.

The following is not covered by Faber's warranty:

1. Service calls to correct the installation of your range hood, to instruct you how to use your range hood, to

replace or repair house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace range hood light bulbs, fuses or filters. Those consumable parts are

excluded from warranty coverage.

3. Repairs when your range hood is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation,

installation not in accordance with electrical or plumbing codes or Faber documentation, or use of products

not approved by Faber.

5. Replacement parts or repair labor costs for units operated outside the United States or Canada, including

any non-UL or C-UL approved Faber range hoods.

6. Repairs to the hood resulting from unauthorized modifications made to the range hood.

7. Expenses for travel and transportation for product service in remote locations and pickup and delivery

charges. Faber range hoods should be serviced in the home.

THIS WARRANTY DOES NOT ALLOW RECOVERY OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, PERSONAL INJURY/WRONGFUL

DEATH OR LOST PROFITS FABER WARRANTY IS LIMITED TO THE ABOVE CONDITIONS AND TO THE WARRANTY PERIOD

SPECIFIED HEREIN AND IS EXCLUSIVE. EXCEPT AS EXPRESSLY SPECIFIED IN THIS AGREEMENT, FABER DISCLAIMS ALL

EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS, AND WARRANTIES INCLUDING, WITHOUT LIMITATION, ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

.

This warranty gives you specific legal rights that may vary from state to state.

Model#: ______________________________ Serial #: _____________________________

La page charge ...

Faber OSTR30SS400 Le manuel du propriétaire

Faber OSTR30SS400 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents