Faber MAES3618SS600B Le manuel du propriétaire

MAES3018SS600-B

MAES3618SS600-B

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

MAESTRALE 18"

MAES3618SS1200-B

MAES4218SS1200-B

MAES4818SS1200-B

2

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START

INSTALLING THIS RANGEHOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium setting.

b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan

orlter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A

RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnofftheburner.

BECAREFULTOPREVENTBURNS.IftheamesdonotgooutimmediatelyEVACUATE

AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will

result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. Thereissmallandcontainedintheareawhereitstarted.

3. Theredepartmentisbeingcalled.

4. Youcanghttherewithyourbacktoanexit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this

fan with any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any

questions, contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the

service disconnecting means to prevent power from being switched on acciden-

tally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or

Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccor-

dance With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sufcientairisneededforpropercombustionandexhaustingofgasesthrough

theue(chimney)offuelburningequipmenttopreventbackdrafting.Followthe

heating equipment manufacturer's guideline and safety standards such as those

publishedbytheNational FireProtectionAssociation(NFPA),andtheAmerican

SocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE),and

the local code authorities.

3

ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST

BE SEALED.

This rangehood requires at least 24" of clearance between the bottom of the rangehood

and the cooking surface or countertop. This hood has been approved by UL at this distance

from the cooktop.

This minimum clearance may be higher depending on local building codes. For gas cooktops

and combination ranges, a minimum of 30" is recommended and may be required.

Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking surface

or countertop. Consult the cooktop or range installation instructions given by the manufacturer

before making any cutouts.

MOBILE HOME INSTALLATION The installation of this rangehood must conform to the

Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly

Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See

Electrical Requirements.

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

!

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the

wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efcient

performance. The size of the ductwork should be uniform. Do not install two elbows together. Use

duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor opening

around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence

that greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts.

Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting

frame must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Do

not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

4. Ducted fans must always be vented to the outdoors.

4

• Electrical ground is required on this rangehood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO

NOT use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or

grounding circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the rangehood is

properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

!

StateofCaliforniaProposition65Warning(USonly)

WARNING

This product contains chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

5

1 MOTOR - RANGEHOOD DIMENSIONS

1 MOTOR - RANGEHOOD DIMENSIONS WITH OPTIONAL FULL CHIMNEY

1 MOTOR - RANGEHOOD DIMENSIONS WITH OPTIONAL TELESCOPIC CHIMNEY

6

2 MOTOR - RANGEHOOD DIMENSIONS

2 MOTOR - RANGEHOOD DIMENSIONS WITH OPTIONAL FULL CHIMNEY

2 MOTOR - RANGEHOOD DIMENSIONS WITH OPTIONAL TELESCOPIC CHIMNEY

7

2 MOTOR RANGEHOOD REAR INFORMATION

1 MOTOR RANGEHOOD REAR INFORMATION

´

´

´

´

´

´

´

10" DUCT TRANSITION FOR 2 MOTOR RANGEHOOD

8

MAIN PARTS 1 MOTOR RANGEHOOD

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with: Con-

trols, Light, Filters, Blower.

10 1 Damper ø 5 7/8"

Ref. Qty. Installation Components

12a 2 Wall plug

14 6 Screws 3/16" x 1 15/16"

Qty. Documentation

1 Instruction Manual

10

1

12a

14

MAIN PARTS 2 MOTOR RANGEHOOD

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with: Con-

trols, Light, Filters, Blower.

10 2 Damper ø 5 7/8"

Ref. Qty. Installation Components

12a 2 Wall plug

14 6 Screws 3/16" x 1 15/16"

Qty. Documentation

1 Instruction Manual

10

1

12a

14

9

Available Accessories

Parts needed

- 6" Round Metal ductwork .

Direct Connect Wiring Box sku # number: WIREBOX

30" Full Width Chimney Duct Cover - sku#FULL30

36" Full Width Chimney Duct Cover - sku#FULL36

42" Full Width Chimney Duct Cover - sku#FULL42

48" Full Width Chimney Duct Cover - sku#FULL48

Telescopic Chimney Duct Cover - TELEMAES

CFM Reducer Accessory Kit - CFMRED

6" Make-Up Air Damper - MUDAMPER6

8" Make-Up Air Damper - MUDAMPER8

Activated Charcoal Filter sku #; FILTER1

Activated Charcoal Filter sku #; FILTER1LL

10" round Duct Transition Kit sku# TRNSPRO

Created by

-

Denomination

-

Lang EN

Sheet

1

/1

Modif.by

Approved by

Approval date

Doc. status

Drawing N.

NEW_DRAWING_BOX

Rev

01

Min. 24" Min. 30"

10

Install Damper that is included with the

Hood before connecting to the ductwork.

One for 1 motor model.

Two for 2 motor model.

Use 2 hands to remove ﬁlters. Turn the knob to the left (counterclockwise) to

release ﬁlter. Repeat with other ﬁlter. Reinstall the ﬁlter by placing the back edge

in the channel at rear of hood. Push ﬁlter into place, turn the knob to the right

(clockwise) to attach to range hood. Repeat with other ﬁlter.

BafeFilterRemoval

Removal / Déplacement

Removal







H

I









H

I









H

I



11

Ducted Venting Options Installation

Horizontal

Vertical

6"

Rear

6"

Ducting Methods

12

Rear Ducted Installation for 1 motor Rangehood





The Electrical Connector must be

removed ﬁrst before converting the

hood to Rear Ducting mode.

For a rear ducting installation the

motor needs to be unsecured by ﬁrst

removing the 12 screws as shown.

Once the screws are removed,

extract the blower from the body

of the Hood and position it so the

transition opening is facing to the

rear wall (from the back remove and

rotate 180 degrees to the left, and

then ip it back 90 degrees as shown

in the diagram).

Once the blower is in place re-install

the 12 screws to fasten the motor to

the Hood body.

Disconnect the Electrical Connector

by depressing the tabs with your

hand and also using light force on

one tab with a at head screwdriver.

Reconnect the Connector to the

blower.

13

Rear Ducted Installation for 2 motor Rangehood





The Electrical Connector must be

removed ﬁrst before converting the

hood to Rear Ducting mode.

The Electrical Connector is always

on the left of left Motor Group.

For a rear ducting installation the

motor needs to be unsecured by ﬁrst

removing the 16 screws as shown.

Once the screws are removed,

extract the blower from the body

of the Hood and position it so the

transition opening is facing to the

rear wall (from the back remove and

rotate 180 degrees to the left, and

then ip it back 90 degrees as shown

in the diagram).

Once the blower is in place re-install

the 16 screws to fasten the motor to

the Hood body.

Disconnect the 2 Electrical Connector,

one from the left motor goup and

one from the right motor Grpoup, by

depressing the tabs with your hand and

also using light force on one tab with a

at head screwdriver.

Reconnect the Connector to the

blower.

Attention: The longhest cable with

connector is always for Left motor

Group, and the shortest cable with

connector is always for Right motor

Group.

Reconnect the Electrical Connector

on the left of left Motor Group.

14

This page needs to be inserted

after Page 9 and before Page 10

Add the new

kit

:DUCTGRT42

–(42“)

RECIRCULATION INSTRUCTIONS

This page needs to be inserted

after Page 9 and before Page 10

Add the new

kit

:DUCTGRT42

–(42“)

Note: It is recommended that pro-

fessional style cooking always be

vented to the outside; for recirculat-

ing Installations, some duct work is

required to exhaust the unit out of

the cabinet.

RECIRCULATING INSTALLATIONS

For recirculating installations, Charcoal Filters are necessary. Remove all grease ﬁlters

and set aside. Attach one charcoal ﬁlter to each end of the blower. Each charcoal ﬁlter

attaches to the grid on the side of the blower. Rotate the ﬁlter clockwise to install and

counterclockwise to remove (FIGURE 3C). Replace all grease ﬁlters.

There are 2 ways to recirculate the Maestrale:

1) Use the Ductless Recirculating Kit (sold separately), refer to installation instructions

inside the Recirculating Kit which includes charcoal ﬁlters.

DUCTGRT30" - (30")

DUCTGRT36" - (36")

2) Some duct work must be installed to exhaust the rangehood back into the kitchen,

either at the top of the cabinet (FIGURE 3A) or at the face or side of the sofﬁt (FIGURE

3B). Install at least 15" of metal duct (ﬁg.3A and 3B) at the air exit. Run the duct vertically

and secure it at the opening cut out at the top or side of the cabinet or sofﬁt. Installation

of metal grill is recommended. This duct work must not terminate into a dead air space.

FILTER1 must be purchased to complete this type of installation.

upper

cabinet

upper

cabinet

rangehood rangehood

open space

enclosed sofﬁt

cooking surface cooking surface

15

Installation for Mounting on the Wall

==

Installation Instruction for mounting on the Wall

Draw a vertical line on the supporting wall

as high as practical, at the center of the

area in which the hood will be installed.

Draw a horizontal line at where the bottom

edge of the hood will be located as indicated

in the ﬁgure that is a minimum of 24" above

cooking surface

1

Min. 24" Min. 30"

16

2

´

[

24”

L

/ ´´

´´

16 13/16”

30”

Mark the wall where indicated, 16 13/16" above the horizontal line and at L distance on the left and

right of vertical line. The distance L change for all dimension of Hood.

Insert the two wall plugs in the holes as shown and ﬁx.

Installation for 1 Motor Rangehood

Installation for 2 Motor Rangehood

´

[

L

/ ´´´

´´´

16 13/16”

24”

30”

Mark the wall where indicated, 16 13/16" above the horizontal line and at L distance on the left and

right of vertical line. The distance L change for all dimension of Hood.

Insert the two wall plugs in the holes as shown and ﬁx.

17

3

4

E

Hook the hood body onto the wall plugs. Use a level to insure that Fixing Bracket is

level and then fully secure the two screws.

5

´

[

Mark the wall where indicated.

Drill directly into ø 5/16" holes at all the center points marked.

Insert the purchased wall plugs in the holes.

Using thhe remaining screws to anchor the hood in holes.

If your installation uses the optional duct cover, ﬁt the cover anges over the brackets. If

installation uses the telescopic chimney extension, ﬁt the extension over the brackets. Install the

upper section ﬁrst, then ﬁt the lower section over the upper section. Seal extension to hood with

clamps.

18

Installation Instruction for Mounting Under the Cabinet

[

Lift the hood to the cabinet.

[

Fix the Hood Body with 4 screws from the bottom.

´

[

Mark the wall where indicated.

Drill directly into ø 5/16" holes at all the center

points marked.

Insert the purchased wall plugs in the

holes.

Using two remaining screws to anchor

the hood in holes.

1

2

3

19

INSTALLATION CONTINUED

Optional Duct Cover Installation

1. Attach the full-width duct cover to the top of the range hood

with the screws provided. The duct cover must be attached

to the top of the range hood before mounting the range hood

to the wall.

A: Distance from center of mounting bracket to centerline:

30" hood: 13 15/32" / 36" hood: 16 15/32" /

42" hood: 19 15/32" / 48" hood: 22 15/32"

B: Mounting brackets

C: Top of hood

2. Install each bracket on the wall as shown. Make sure the

screws and brackets are securely fastened to the wall.

IMPORTANT: Install only the brackets. Do not install the

hood.

Optional Telescopic Chimney Extension Installation

1. If a chimney extension is used, attach the extension brackets

as shown. Make sure that the screws are securely fastened to

the wall.

A: Ceiling

B: Brackets

C. Top of hood

INSTALLATION CONTINUED

1. Attach the full-width duct cover to the top of the range hood with the screws provided. The duct

cover must be attached to the top of the range hood before mounting the range hood to the wall.

A: Distance from center of mounting bracket to centerline:

30" hood: 13 15/32"

36" hood: 16 15/32"

42" hood: 19 15/32"

48" hood: 22 15/32"

B: Mounting brackets

C: Top of hood

2. Install each bracket on the wall as shown. Make sure the screws and brackets are securely

fastened to the wall. IMPORTANT: Install only the brackets. Do not install the hood.

Optional Duct Cover Installation

INSTALLATION CONTINUED

Optional Duct Cover Installation

1. Attach the full-width duct cover to the top of the range hood

with the screws provided. The duct cover must be attached

to the top of the range hood before mounting the range hood

to the wall.

A: Distance from center of mounting bracket to centerline:

30" hood: 13 15/32" / 36" hood: 16 15/32" /

42" hood: 19 15/32" / 48" hood: 22 15/32"

B: Mounting brackets

C: Top of hood

2. Install each bracket on the wall as shown. Make sure the

screws and brackets are securely fastened to the wall.

IMPORTANT: Install only the brackets. Do not install the

hood.

Optional Telescopic Chimney Extension Installation

1. If a chimney extension is used, attach the extension brackets

as shown. Make sure that the screws are securely fastened to

the wall.

A: Ceiling

B: Brackets

C. Top of hood

Optional Telescopic Chimney Extension Installation

1. If a chimney extension is used, attach the extension brackets as shown. Make sure that the

screws are securely fastened to the wall.

A: Ceiling

B: Brackets

C: Top of hood

20

Direct Connect Wiring Box

Accessory sku # WIREBOX

(purchased separately)

Created by

-

Denomination

-

Lang EN

Sheet

1

/1

Modif.by

Approved by

Approval date

Doc. status

Drawing N.

NEW_DRAWING_BOX

Rev

01

ELECTRICAL INSTALLATION WITH CONNECTION CABLE

ELECTRICAL INSTALLATION WITH

OPTIONAL WIRING BOX

For Permanent wiring Installation-Use only

with Listed rangehood Wiring Box kit

sku # WIREBOX, manufactured by Faber.

Max. 33 7/16”

GROUNDING INSTRUCTIONS This appliance must

be grounded. In the event of an electrical short circuit,

grounding reduces the risk of electric shock by providing

an escape wire for the electric current. This appliance

is equipped with a cord having a grounding wire with a

grounding plug. The plug must be plugged into an outlet

that is properly installed and grounded.

WARNING - Improper grounding can result in a risk of

electric shock.

Consult a qualiﬁed electrician if the grounding instructions

are not completely understood, or if doubt exists as to

whether the appliance is properly grounded.

Do not use an extension cord. If the power supply cord

is too short, have a qualiﬁed electrician install an outlet

near the appliance.

Replace the ﬁlters removed previously.

La page charge ...

Faber MAES3618SS600B Le manuel du propriétaire

Faber MAES3618SS600B Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents