Faber Inca Smart 28 Stainless Steel 240 Le manuel du propriétaire

INSP28SS400

INSP28SS600

INCA SMART

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

Instrucciones de instalación

Información de uso y cuidado

2

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START

INSTALLING THIS RANGE HOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on low or medium setting.

b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or

lter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE

TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnoffthe

burner.BECAREFULTOPREVENTBURNS.Iftheamesdonotgooutimmediately

EVACUATE AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will

result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate

it.

2. Thereissmallandcontainedintheareawhereitstarted.

3. Theredepartmentisbeingcalled.

4. Youcanghttherewithyourbacktoanexit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan with

any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any questions,

contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service

disconnecting means to prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or Explosive

Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccordance

With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sufcientairisneededforpropercombustionandexhaustingofgasesthroughthe

ue(chimney)offuelburningequipmenttopreventbackdrafting.Followtheheating

equipment manufacturer's guideline and safety standards such as those published by

theNationalFireProtectionAssociation(NFPA),andtheAmericanSocietyforHeating,

RefrigerationandAirConditioningEngineers(ASHRAE),andthelocalcodeauthorities.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other

hidden utilities.

3

4. Ducted fans must always be vented to the outdoors.

ALL WALL AND FLOOR OPENINGS WHERE THE RANGE HOOD IS INSTALLED MUST

BE SEALED.

This Range Hood requires at least 24" of clearance between the bottom of the Range Hood

and the cooking surface or countertop. This hood has been approved by UL at this distance from

the cooktop.

This minimum clearance may be higher depending on local building codes. For gas cooktops and

combination ranges, a minimum of 30" is recommended and may be required.

Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking surface

or countertop. Consult the cooktop or range installation instructions given by the manufacturer

before making any cutouts.

MOBILE HOME INSTALLATION The installation of this Range Hood must conform to the Manufactured

Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly Federal Standard

for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See Electrical Requirements.

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

!

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through

the wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efcient

performance. The size of the ductwork should be uniform. Do not install two elbows together. Use

duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor opening

around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence that

greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts.

Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting

frame must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Do

not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

Cold Weather installations

An additional back draft damper should be installed to minimize backward cold air ow and a

nonmetallic thermal break should be installed to minimize conduction of outside temperatures

as part of the vent system. The damper should be on the cold air side of the thermal break.

The break should be as close as possible to where the vent system enters the heated portion

of the house.

4

• Electrical ground is required on this Range Hood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO NOT

use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding

circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the Range Hood is

properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

!

StateofCaliforniaProposition65Warning(USonly)

WARNING

This product contains chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A time-de-

lay fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance

with the electrical rating of this unit as specied on the serial/rating plate located inside the unit near

the eld wiring compartment.

5

RANGE HOOD DIMENSIONS 28"

47 "

6

MIN. 24" OVER ELECTRIC

INSTALLATION HEIGHT REQUIREMENTS

MIN. 30" OVER GAS

7

12a Pozi Screws (1/8" x 5/8")

10

12b Pozi Screws (1/8" x 1/2")

4

12e Torx Screws (1/8" x 3/8")

2

Torx Screwdriver

Pozi Screwdriver







H

I









H

I









H

I



12b

12e

8

12a

MAIN PARTS

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with: Controls, Light, Filters,Blower.

8 1 Recirculation Vent Grill

10 2 Flap

11 1 Ring

Ref. Qty. Installation Components

12a 10 Screws (for hood installation)

12b 4 Screws 1/8"x1/2" (for Cover installation)

12e 2 Screws 1/8"x3/8" (for Recirculation Vent Grill mounting)

Qty. Documentation

1 Instruction Manual







H

I



10







H

I



11

8

Available Accessories

Parts needed

- 6" Round Metal ductwork .

Direct Connect Wiring Box sku # WIREBOX

Liner 30" Stainless #LINE30ST

Liner 36" Stainless #LINE36ST

Activated Charcoal Filter sku #; FILTER1

Activated Charcoal Filter sku #; FILTER1LL

Created by

-

Denomination

-

Lang EN

Sheet

1

/1

Modif.by

Approved by

Approval date

Doc. status

Drawing N.

NEW_DRAWING_BOX

Rev

01

Two men required for installation Wear work gloves for safety

9

LINER DIMENSIONS

Version 09/14 - Page 4

SIDE VIEW / LA PERSPECTIVE DE CÔTÉ

FRONT VIEW / LA PERSPECTIVE DE FRONT

BOTTOM VIEW / LA PERSPECTIVE DE BAS

Standard Liner 36 Stainless (LINE36ST)

designed for 36” wide installations

Cadre Standard 36 Axier Inoxydable (LINE36ST)

peut être employée les hottes encastrable sur mesure de 36"

Standard Liner 30 Stainless (LINE30ST)

designed for 30” wide installations

Cadre Standard 30 Axier Inoxydable (LINE30ST)

peut être employée les hottes encastrable sur mesure de 30"

Note: Standard Liners are pre-cut for installation of Inca Smart. For installations with the Inca HC SS, remove the additional perforated section.

Note: Les Cadres Standard sont précoupés pour l'installation de l'Inca Smart. Pour des installations avec L'Inca HC SS, enlevez la section perforée

additionnelle.

RANGEHOOD DIMENSIONS / DIMENSIONS DE LA HOTTE

LINER DIMENSIONS / DIMENSIONS DU CADRE

Pre-Planning Your Installation -

Important: The recommended height to install this hood off the cooktop is

a minimum of 24" and a maximum of 30” for maximum effectiveness. Also consult the cooktop manufacturer’s

recommendation.

Planiez votre installation - Important : La hauteur recommandée pour installer cette hotte au-dessus de la

surface de cuisson est d’un minimum de 24” et d’un maximum de 30” pour un maximum d’efcacité. De plus,

nous vous recommandons consulter le manuel de recommandations du fabricant de la surface de cuisson.

NOTE: Remove the metal packaging support

piece from the top of the hood before

installation (SEE RIGHT)

NOTE : Enlevez le morceau de empaquetage de

soutien en métal du dessus du hotte avant

installation (VOYEZ BIEN)

Version 09/14 - Page 4

SIDE VIEW / LA PERSPECTIVE DE CÔTÉ

FRONT VIEW / LA PERSPECTIVE DE FRONT

BOTTOM VIEW / LA PERSPECTIVE DE BAS

Standard Liner 36 Stainless (LINE36ST)

designed for 36” wide installations

Cadre Standard 36 Axier Inoxydable (LINE36ST)

peut être employée les hottes encastrable sur mesure de 36"

Standard Liner 30 Stainless (LINE30ST)

designed for 30” wide installations

Cadre Standard 30 Axier Inoxydable (LINE30ST)

peut être employée les hottes encastrable sur mesure de 30"

Note: Standard Liners are pre-cut for installation of Inca Smart. For installations with the Inca HC SS, remove the additional perforated section.

Note: Les Cadres Standard sont précoupés pour l'installation de l'Inca Smart. Pour des installations avec L'Inca HC SS, enlevez la section perforée

additionnelle.

RANGEHOOD DIMENSIONS / DIMENSIONS DE LA HOTTE

LINER DIMENSIONS / DIMENSIONS DU CADRE

Pre-Planning Your Installation -

Important: The recommended height to install this hood off the cooktop is

a minimum of 24" and a maximum of 30” for maximum effectiveness. Also consult the cooktop manufacturer’s

recommendation.

Planiez votre installation - Important : La hauteur recommandée pour installer cette hotte au-dessus de la

surface de cuisson est d’un minimum de 24” et d’un maximum de 30” pour un maximum d’efcacité. De plus,

nous vous recommandons consulter le manuel de recommandations du fabricant de la surface de cuisson.

NOTE: Remove the metal packaging support

piece from the top of the hood before

installation (SEE RIGHT)

NOTE : Enlevez le morceau de empaquetage de

soutien en métal du dessus du hotte avant

installation (VOYEZ BIEN)

Pre-Planning your Installation - Important: The recommended height to install this hood off the

cooktop is a minimum of 24" and a maximum 30" for maximum effectiveness. Also consult the

cooktop manufacturer's recommendation.

StandardLiner30Stainless(LINE30ST)designedfor30”wideinstallations

StandardLiner36Stainless(LINE36ST)designedfor36”wideinstallations

10

FOR INSTALLATION WITH LINERS

When building a custom hood, always

follow all applicable codes and

standards.

WARNING

!

The Inca Smart can be used in

standard 30" or 36" wide cabinetry

or with custom hoods 30" wide

and up.

For custom/wood hoods,

choose either YOUR OWN

custom liner or our Standard

Liner designed for 30" and

36" wide installations. Liners

create a perfectly - sealed,

non-combustible nish for the

underside of your custom/

wood hood.

The Standard Liners are made

up of two sections: a larger,

rear section (pre-cut out for

insertion of the Inca Smart)

and a front section for a total

adjustable depth between 16"

and 17 7/8".

!!! IMPORTANT NOTE: DO NOT

REMOVE THE ADDITIONAL

PERFORATED SECTION AROUND

THE PRE-CUT-OUT WHEN

INSTALLING THE STANDARD

LINER WITH THE INCA SMART

MODEL.

Consider the shape, size,

and weight of the Inca Smart

and Liner to determine the

conguration of the custom/

wood hood.

See RANGEHOOD DIMENSIONS

AND LINER DIMENSIONS.

1. The custom/wood hood must have a sturdy base (3/4" plywood

recommended) to accomodate the cut-out for the Inca Smart. The base

must be recessed to accomodate the height of the Liner (see LINER

DIMENSIONS). The Liner attaches to the bottom of the base using

screws appropriate for the size and material of your custom/wood hood.

The Inca Smart inserts into the cut-out in the Liner and base.

2. Position the rear section of the Liner so that it abuts the back edge of

your custom/wood hood. Using a pen, trace the outline of the pre-cut out.

Remove the Liner and proceed to MAKE YOUR CUT-OUTS.

Install both sections of the Liner and proceed to INSTALL THE

RANGEHOOD.

Version 09/14 - Page 5

The Inca Smart requires 5" round ductwork. To ensure that the blower performs to its

highest possible capacity, ductwork should be as short and straight as possilbe.

Make your ductrun as straight and short as possible. The ductrun should not exceed 25

equivalent feet if ducted with the required minimum of 5" round duct. Count 45º angles

as 3 feet, 90º elbows as 5 feet, and 90º at elbows as 12 feet.

For best results, use no more than three 90° elbows. Make sure that there is a minimum

of 24" of straight duct between elbows if more than one is used. Do not install two

elbows together. If you must elbow right away, do it as far away from the hood's

exhaust opening as possible.

TOOLS NEEDED FOR INSTALLATION

• Saber Saw or Jig Saw

• Drill

• 1 1/4" Wood Drill Bit

• Pliers

• Phillips Screwdriver

• Wire Stripper or Utility Knife

• Metal Snips

• Measuring Tape or Ruler

• Level

• Pencil

• Caulking Gun

• Duct Tape

PLAN YOUR DUCTWORK

The Inca Smart can be used in

standard 30" or 36" wide cabinetry

or with custom hoods 30" wide

and up.

For custom/wood hoods, choose

either YOUR OWN custom liner or

our Standard Liner designed for 30"

and 36" wide installations. Liners

create a perfectly-sealed, non-

combustible nish for the underside

of your custom/wood hood.

The Standard Liners are made

up of two sections: a larger, rear

section (pre-cut out for insertion of

the Inca Smart) and a front section

for a total adjustable depth between

16" and 17

7/8".

!!! IMPORTANT NOTE: DO NOT

REMOVE THE ADDITIONAL

PERFORATED SECTION

AROUND THE PRE-CUT-

OUT WHEN INSTALLING

THE STANDARD LINER WITH

THE INCA SMART MODEL.

THIS PERFORATION IS ONLY

REMOVED FOR USE WITH THE

INCA HC SS MODEL.

Consider the shape, size, and

weight of the Inca Smart and Liner

to determine the configuration

of the custom/wood hood. See

RANGEHOOD DIMENSIONS AND

LINER DIMENSIONS on Page 4.

FOR INSTALLATIONS WITH LINERS

PARTS SUPPLIED FOR INSTALLATION

• 1 Backdraft Damper

• 10 Screws

• Field Wiring Box

• 1 Literature Package

PARTS NEEDED FOR INSTALLATION

• 2 Conduit Connectors

• Power Supply Cable

• Scews for Field Wiring Box

• 1 Wall or Roof Cap

• All Metal Ductwork

OPTIONAL ACCESSORIES AVAILABLE

• Charcoal Filter Kit

For recirculating installations only,

replace charcoal lters as needed

part # FILTER4

• Liners

Create a perfectly-sealed, non-combustible

perimeter around the Inca Smart. Depth adjustable

from 16" - 17

7/8"

.

Standard Liner 30 Stainless - part #

LINE30ST

Standard Liner 36 Stainless - part # LINE36ST

CUSTOM/WOOD

HOOD

STANDARD LINER

INCA SMART

WARNING

!

When building a custom hood,

always follow all applicable

codes and standards.

1. The custom/wood hood must have a sturdy base (3/4" plywood recommended) to accomodate

the cut-out for the Inca Smart. The base must be recessed to accomodate the height of the

Liner (see LINER DIMENSIONS on Page 4). The Liner attaches to the bottom of the base

using screws appropriate for the size and material of your custom/wood hood. The Inca Smart

inserts into the cut-out in the Liner and base.

2. Position the rear section of the Liner so that it abuts the back edge of your custom/wood

hood. Using a pen, trace the outline of the pre-cut out. Remove the Liner and proceed to MAKE

YOUR CUT-OUTS on Page 6. Install both sections of the Liner and proceed to INSTALL THE

RANGEHOOD on Page 6.

CUSTOM/WOODH

HOOD

STANDARD LINER

INCA SMART

11

Choose your ducting method

Rear

Top

6"

Non Ducted - RecirculationDucted Venting Installation

Requires purchase of Activated

Charcoal Accessory #Filter1

Caution: If an elbow is required,

do it as far away from the hood's

exhaust opening as possible.

12

1

Remove grease lters and set aside.

INSTALL THE RANGE HOOD

2

Remove the bottom of the Range Hood by pulling as shown.

13

3

The Hood can be installed directly on the underside of the cabinet (minimum 24" for electric ranges

and 30" for gas ranges).

Create an opening in the bottom of the Cabinet, as shown.

10 1/2”

1/2”

26” 5/8

10 1/2”

1/2”

26” 5/8

1/2”

10 1/4”

26” 5/8

1/2”

Attention: The cabinet must be accessible so that you can access the hood cable and

plug in the future, after installing the product

14

10 1/2”

1/2”

26” 5/8

Min.9/16"

Max 1" 3/16

Vf

Insert the hood until the side supports snap into place.

Lock in position by tightening the screws Vf from underneath the hood.

4

Fasten using the 10 screws 12a provided.

5

15

Replace the bottom of the Range Hood by 4 screws 12b as shown.

Place the grease lters in the hood

6

7

12b

16

Ducted Venting Installation

8

Non Ducted -

Recirculation Option

Install the 2 Flap 10 included with the

Range Hood as shown.

Break the 4 pre-cutting pieces and install

the Ring 11 included with the Range

Hood before connecting to the ductwork.

Install Roof or Wall Cap purchased

separately. Connect the 6" metal duct-

work to the Roof or Wall Cap and then

attach ductwork.





´

For Non-Ducted Recirculation venting route

the ductwork to a location above the hood

where the discharge is vented back into the

room.

Use the included Recirculation Vent Grill to

cover the opening. Secure the grill with the

2 screws provided in the Install Kit.

Required Activated Charcoal

Filter Accessory - sku #FILTER1

or #FILTER1LL

CHOOSE YOUR DUCTING METHOD

12e

8

Torx Screwdriver

10

11

17

Direct Connect Wiring Box

Accessory sku # WIREBOX

(purchased separately)

Created by

-

Denomination

-

Lang EN

Sheet

1

/1

Modif.by

Approved by

Approval date

Doc. status

Drawing N.

NEW_DRAWING_BOX

Rev

01

ELECTRICAL INSTALLATION WITH

OPTIONAL WIRING BOX

For Permanent wiring Installation-Use only

with Listed Range Hood Wiring Box kit

sku # WIREBOX, manufactured by Faber.

Max. 33 7/16”

9

ELECTRICAL INSTALLATION WITH CONNECTION CABLE

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding

reduces the risk of electric shock by providing an escape wire for the electric current.

This appliance is equipped with a cord having a grounding wire with a grounding

plug. The plug must be plugged into an outlet that is properly installed and grounded.

WARNING - Improper grounding can result in a risk of electric shock.

Consult a qualied electrician if the grounding instructions are not completely under-

stood, or if doubt exists as to whether the appliance is properly grounded.

Do not use an extension cord. If the power supply cord is too short, have a qualied

electrician install an outlet near the appliance.

18

1

2

10

For Non-Ducted Recirculation Option

Attach each charcoal lter to the black

grid on each side of the blower. Press the

charcoal lter tightly to the black grid on the

blower side and rotate the lter clockwise

(towards the front of the insert hood) until

it locks into place. Turn counterclockwise

(towards the back of the insert hood) to

remove.

Required Activated Charcoal Filter

Accessory - sku sku #FILTER1 or

#FILTER1LL

19

USE AND CARE INFORMATION

For Best Results

Start the Range Hood several minutes before cooking to develop proper airow. Allow the

Range Hood to operate for several minutes after cooking is complete to clear all smoke and

odors from the kitchen.

Button Function

LED indicator light (L) - indicates current speed with color

Green - speed 1

Orange - speed 2

Red - speed 3

Flashing Red - intensive speed

Light On/Off Button

On/Off switch for the lights.

Press the button to turn the light ON and press again to turn it OFF.

Blower On/Off Button

On/Off button for the blower.

Press the button to turn the blower ON to speed one (indicated by green LED)

and press again to turn the hood off.

Blower Speed 2

Press this button to turn the hood onto speed #2. (indicated by orange LED).

Blower Speed 3 / Intensive

Press this button to turn the hood onto speed #3. (indicated by solid red LED)

Hold down the speed 3 button for 2 seconds to activate the intensive speed.

The intensive speed setting is indicated by a blinking red light.

This operates the hood for 10 minutes on the highest speed and then returns to

the previous speed.

20

Cleaningmetalgreaselters

The metal grease lters can be cleaned in hot detergent

solution or washed in the dishwasher. They should be

cleaned every 2 months use, or more frequently if use

is particularly heavy.

• Remove the lter, pushing the lever towards the back

of the unit and at the same time pulling downward.

• Wash the lter without bending it, leave it to dry

thoroughly before replacing (if the surface of the lter

changes color over time, this will have absolutely no

effect on its efciency).

• Replace, taking care to ensure that the handle faces

forward.

• Cleaning in dishwasher may dull the nish of the

metal grease lter.

• No water can be present in lters before installing

back in hood.

Cleaning Exterior surfaces

Cleaning Exterior surfaces:

Please note, abrasives and scouring agents can scratch

range hood nishes and should not be used to clean

nished surfaces.

Stainless Steel nish cleaning instructions:

Clean exterior surfaces with a commercially available

stainless steel cleaner.

Painted Gray nish cleaning instructions:

Clean exterior surfaces with hot soapy water.

Replacing Activated Charcoal Filter

The Activated Charcoal Filters are not washable

and cannot be regenerated, and must be replaced

approximately every 4 months of operation, or more

frequently with heavy usage.

• Remove the Filter, pushing it towards the back of the

unit and at the same time pulling downward.

• Remove the saturated Activated Charcoal Filters,

as indicated (A).

• Fit the new Filters, as indicated (B).

• Replace, taking care to ensure that the handle faces

forwards.

Caution: When used in recirculation mode, to

Reduce the Risk of Fire and Shock use only con-

version kit Model FILTER1 or FILTER1LL.





La page charge ...

Faber Inca Smart 28 Stainless Steel 240 Le manuel du propriétaire

Ce manuel convient également à

Faber Inca Smart 28 Stainless Steel 240 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents