Generac 14 kW 0056120 Manuel utilisateur

Owner’s Manual

8, 10, 12, 14, 16, 17 & 20kW Air-cooled,

Automatic Standby Generators

DANGER

DEADLY EXHAUST FUMES. OUTDOOR INSTALLATION ONLY!

Not intended for use as Primary Power in place of utility

or in life-support applications.

 

L

I

S

T

E

D

C

U

S

DO NOT LIFT UNIT BY ROOF!

INTRODUCTION

Thank you for purchasing this compact, high performance, air-

cooled, engine-driven generator. It is designed to automatically

supply electrical power to operate critical loads during a utility

power failure.

This unit is factory installed in an all-weather, metal enclosure and

is intended exclusively for outdoor installation. This generator

will operate using either vapor withdrawn liquid propane (LP) or

natural gas (NG).

NOTE:

This generator is suitable for supplying typical residential loads

such as Induction Motors (sump pumps, refrigerators, air con-

ditioners, furnaces, etc.), Electronic Components (computer,

monitor, TV, etc.), Lighting Loads and Microwaves.

READ THIS MANUAL THOROUGHLY 

If any portion of this manual is not understood, contact the nearest

Dealer for starting, operating and servicing procedures.

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

operation that may be hazardous if performed incorrectly or care-

lessly. Observe them carefully. Their definitions are as follows:

DANGER

After this heading, read instructions that, if not

strictly complied with, will result in serious per-

sonal injury, including death.

After this heading, read instructions that, if not

strictly complied with, could result in serious per-

sonal injury, including death.

After this heading, read instructions that, if not

strictly complied with, might result in minor or mod-

erate injury.

NOTE:

After this heading, read instructions that, if not strictly complied

with, may result in damage to equipment and/or property.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the service are essential to pre-

venting accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates follows:



This symbol points out important safety

information that, if not followed, could endanger

personal safety and/or property of others.



This symbol points out potential explosion

hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical shock

hazard.

The operator is responsible for proper and safe use of the equip-

ment. The manufacturer strongly recommends that the operator

read this Owner's Manual and thoroughly understand all instruc-

tions before using this equipment. The manufacturer also strongly

recommends instructing other users to properly start and operate

the unit. This prepares them if they need to operate the equipment

in an emergency.

CONTENTS 

This manual contains pertinent owner’s information for these

models:

7 kW NG, 8 kW LP, single-cylinder GH-410 Engine•

9 kW NG, 10 kW LP, V-twin GT-530 Engine•

12 kW NG, 12 kW LP, V-twin GT-990 Engine•

13 kW NG, 14 kW LP, V-twin GT-990 Engine•

16 kW NG, 16 kW LP, V-twin GT-990 Engine•

16 kW NG, 17 kW LP, V-twin GT-990 Engine•

18 kW NG, 20 kW LP, V-twin GT-999 Engine•

OPERATION AND MAINTENANCE 

It is the operator's responsibility to perform all safety checks, to

make sure that all maintenance for safe operation is performed

promptly, and to have the equipment checked periodically by a

Dealer. Normal maintenance service and replacement of parts

are the responsibility of the owner/operator and, as such, are not

considered defects in materials or workmanship within the terms

of the warranty. Individual operating habits and usage contribute to

the need for maintenance service.

Proper maintenance and care of the generator ensures a minimum

number of problems and keep operating expenses at a minimum.

See a Dealer for service aids and accessories.

HOW TO OBTAIN SERVICE 

When the generator requires servicing or repairs, contact a Dealer

for assistance. Service technicians are factory-trained and are

capable of handling all service needs.

When contacting a Dealer about parts and service, always supply

the complete model number and serial number of the unit as given

on its data decal, which is located on the generator. See section "The

Generator" for decal location.

Model No. _________________ Serial No. ______________

Table of Contents

Air-cooled Generators

1

Introduction .................... Inside Front Cover

Read This Manual Thoroughly .............................................IFC

Contents ............................................................................IFC

Operation and Maintenance.................................................IFC

How to Obtain Service ........................................................IFC

Table of Contents ........................................ 1

Safety Rules .................................................2

Standards Index .....................................................................3

Section 1 – General Information ................. 4

1.1 Unpacking/Inspection .....................................................4

1.2 Protection Systems ........................................................4

1.3 NEC Requirement for Arc Fault Circuit

Interruption Breaker for Bedrooms ..................................4

1.4 Emission Information......................................................5

1.5 The Generator ................................................................6

1.6 Specifications ................................................................7

1.7 System Set LED .............................................................8

1.8 Fuel Requirements and Recommendations ......................8

1.9 Fuel Consumption ..........................................................8

1.10 Reconfiguring the Fuel System ........................................9

1.11 Location .......................................................................10

1.12 Battery Requirements ...................................................11

1.13 Battery Installation ........................................................13

1.14 The Battery ..................................................................13

1.15 Battery Charger ............................................................14

Section 2 – Post Installation Start-up

and Adjustments ....................14

2.1 Before Initial Startup .....................................................14

2.2 Check Transfer Switch Operation ..................................14

2.3 Electrical Checks ..........................................................14

2.4 Generator Tests Under Load ..........................................15

2.5 Checking Automatic Operation ......................................15

2.6 Engine Governor Adjustment ........................................16

2.7 Voltage Regulator Adjustment .......................................16

Section 3 – Operation ................................ 17

3.1 Control Panel Interface .................................................17

3.2 Automatic Transfer Operation ........................................18

3.3 Sequence of Automatic Operation .................................19

3.4 Manual Transfer Operation ............................................20

3.5 Side Compartment (V-twin Only) ..................................20

3.6 Protection Systems ......................................................21

Section 4 – Maintenance ...........................22

4.1 Fuse .............................................................................22

4.2 Checking the Engine Oil Level .......................................22

4.3 Changing the Engine Oil ................................................23

4.4 Changing the Engine Air Cleaner ...................................24

4.5 Spark Plug(s) ...............................................................25

4.6 Battery Maintenance .....................................................25

4.7 Adjusting GH-410/GT-530/990/999 Valve Clearance ......26

4.8 Cooling System ............................................................27

4.9 Attention After Submersion ...........................................27

4.10 Corrosion Protection.....................................................27

4.11 Out of Service Procedure ..............................................27

4.12 Service Schedule .........................................................29

Section 5 – Troubleshooting ..................... 30

5.1 Troubleshooting Guide ..................................................30

Section 6 – Appendix ................................ 31

6.1 Menu System Navigation ..............................................31

Section 7 – Installation Diagrams ............. 33

Section 8 – Warranty ................................. 36

2

Study these SAFETY RULES carefully before installing, operating

or servicing this equipment. Become familiar with this Owner’s

Manual and with the unit. The generator can operate safely, effi-

ciently and reliably only if it is properly installed, operated and

maintained. Many accidents are caused by failing to follow simple

and fundamental rules or precautions.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all-inclusive. If

using a procedure, work method or operating technique the manu-

facturer does not specifically recommend, ensure that it is safe for

others. Also make sure the procedure, work method or operating

technique utilized does not render the generator unsafe.

DANGER



Despite the safe design of this generator,

operating this equipment imprudently, neglecting

its maintenance or being careless can cause

possible injury or death. Permit only responsible

and capable persons to install, operate and main-

tain this equipment.



Potentially lethal voltages are generated by

these machines. Ensure all steps are taken to

render the machine safe before attempting to

work on the generator.



Parts of the generator are rotating and/or hot

during operation. Exercise care near running

generators.



Installation must always comply with applicable

codes, standards, laws and regulations.



A running generator gives off carbon monoxide,

and odorless, colorless poison gas. Breathing in

carbon monoxide can cause headaches, fatigue,

diziness, nausea, vomitting, confusion, fainting,

siezures or death.



GENERAL HAZARDS



For safety reasons, the manufacturer recommends that this equip-•

ment be installed, serviced and repaired by a Service Dealer or

other competent, qualified electrician or installation technician who

is familiar with applicable codes, standards and regulations. The

operator also must comply with all such codes, standards and

regulations.

The engine exhaust fumes contain carbon monoxide, which •

can be DEADLY. This dangerous gas, if breathed in sufficient

concentrations, can cause unconsciousness or even death.

Do NOT alter or add to the exhaust system or do anything that

might render the system unsafe or in noncompliance with appli-

cable codes and standards.

Install a battery operated carbon monoxide alarm indoors, •

according to manufacturer's instructions/recommendations.

Adequate, unobstructed flow of cooling and ventilating air is •

critical to correct generator operation. Do not alter the instal-

lation or permit even partial blockage of ventilation provisions,

as this can seriously affect safe operation of the generator. The

generator MUST be installed and operated outdoors only.

Keep hands, feet, clothing, etc., away from drive belts, fans, •

and other moving or hot parts. Never remove any drive belt or

fan guard while the unit is operating.

When working on this equipment, remain alert at all times. •

Never work on the equipment when physically or mentally

fatigued.

Inspect the generator regularly, and contact the nearest Dealer •

for parts needing repair or replacement.

Before performing any maintenance on the generator, discon-•

nect its battery cables to prevent accidental start up. Disconnect

the cable from the battery post indicated by a NEGATIVE, NEG

or (–) first, then remove the POSITIVE, POS or (+) cable. When

reconnecting the cables, connect the POSITIVE cable first, the

NEGATIVE cable last.

Never use the generator or any of its parts as a step. Stepping •

on the unit can stress and break parts, and may result in dan-

gerous operating conditions from leaking exhaust gases, fuel

leakage, oil leakage, etc.



ENGINE EXHAUST HAZARDS



Generator engine exhaust contains DEADLY carbon monox-•

ide, an odorless, colorless poisonous gas. Breathing carbon

monoxide can cause: dizziness, throbbing temples, nausea,

muscular twitching, headache, vomiting, weakness and sleepi-

ness, inability to think clearly, fainting, unconsciousness or

even death. If you experience any carbon monoxide poisoning

symptoms, move into fresh air and immediately seek medical

attention.

Never operate the generator set with the vehicle inside any •

garage or other enclosed area.

IMPORTANT SAFETY INSTRUCTIONS

Air-cooled Generators



SAVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe operation be copied and posted near

the unit’s installation site. Safety should be stressed to all operators and potential operators of this equipment.



The engine exhaust from this product

contains chemicals known to the state

of California to cause cancer, birth

defects or other reproductive harm.

WARNING:



This product contains or emits chemicals

known to the state of California to cause

cancer, birth defects or other reproductive harm.

WARNING:



3



ELECTRICAL HAZARDS



All generators covered by this manual produce dangerous •

electrical voltages and can cause fatal electrical shock. Utility

power delivers extremely high and dangerous voltages to the

transfer switch as does the standby generator when it is in

operation. Avoid contact with bare wires, terminals, connec-

tions, etc., while the unit is running. Ensure all appropriate

covers, guards and barriers are in place, secured and/or locked

before operating the generator. If work must be done around

an operating unit, stand on an insulated, dry surface to reduce

shock hazard.

Do not handle any kind of electrical device while stand-•

ing in water, while barefoot, or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

The National Electrical Code (NEC) requires the frame and external •

electrically conductive parts of the generator to be connected to

an approved earth ground. Local electrical codes also may require

proper grounding of the generator electrical system.

After installing this home standby electrical system, the genera-•

tor may crank and start at any time without warning. When this

occurs, load circuits are transferred to the STANDBY (genera-

tor) power source. To prevent possible injury if such a start and

transfer occur, always set the generator’s AUTO/OFF/MANUAL

switch to its OFF position before working on equipment and

remove the 15A fuse from the generator control panel.

In case of accident caused by electric shock, immediately shut •

down the source of electrical power. If this is not possible,

attempt to free the victim from the live conductor. AVOID DIRECT

CONTACT WITH THE VICTIM. Use a nonconducting implement,

such as a dry rope or board, to free the victim from the live

conductor. If the victim is unconscious, apply first aid and get

immediate medical help.

Never wear jewelry when working on this equipment. Jewelry •

can conduct electricity resulting in electric shock, or may get

caught in moving components causing injury.



FIRE HAZARDS



For fire safety, the generator must be installed and maintained •

properly. Installation must always comply with applicable

codes, standards, laws and regulations. Adhere strictly

to local, state and national electrical and building codes.

Comply with regulations the Occupational Safety and Health

Administration (OSHA) has established. Also, ensure that the

generator is installed in accordance with the manufacturer’s

instructions and recommendations. Following proper installa-

tion, do nothing that might alter a safe installation and render

the unit in noncompliance with the aforementioned codes,

standards, laws and regulations.

Keep a fire extinguisher near the generator at all times. •

Extinguishers rated “ABC” by the National Fire Protection

Association are appropriate for use on the standby electric

system. Keep the extinguisher properly charged and be familiar

with its use. Consult the local fire department with any ques-

tions pertaining to fire extinguishers.



EXPLOSION HAZARDS



Do not smoke around the generator. Wipe up any fuel or oil •

spills immediately. Ensure that no combustible materials are left

in the generator compartment, or on or near the generator, as

FIRE or EXPLOSION may result. Keep the area surrounding the

generator clean and free from debris.

Gaseous fluids such as natural gas and liquid propane (LP) •

gas are extremely EXPLOSIVE. Install the fuel supply system

according to applicable fuel-gas codes. Before placing the

home standby electric system into service, fuel system lines

must be properly purged and leak tested according to applica-

ble code. After installation, inspect the fuel system periodically

for leaks. No leakage is permitted.

STANDARDS INDEX 

In the absence of pertinent standards, codes, regulations and

laws, the published information listed below may be used for

installation guidance for this equipment.

1. NFPA No. 37, STATIONARY COMBUSTION ENGINES AND

GAS TURBINES, available from the National Fire Protection

Association, 470 Atlantic Avenue, Boston, MA 02210.

2. NFPA No. 76A, ESSENTIAL ELECTRICAL SYSTEMS FOR

HEALTH CARE FACILITIES, available same as Item 1.

3. NFPA No. 54, NATIONAL FUEL GAS CODE, available same as

Item 1.

4. NFPA No. 58, AMERICAN NATIONAL STANDARD FOR

STORAGE AND HANDLING OF LIQUEFIED PETROLEUM GAS,

available same as Item 1.

5. NFPA No. 70, NFPA HANDBOOK OF NATIONAL ELECTRIC

CODE, available same as Item 1.

6. Article X, NATIONAL BUILDING CODE, available from the

American Insurance Association, 85 John Street, New York,

N.Y. 10038.

7. AGRICULTURAL WIRING HANDBOOK, available from the Food

and Energy Council, 909 University Avenue, Columbia, MO

65201.

8. ASAE EP-3634, INSTALLATION AND MAINTENANCE OF

FARM STANDBY ELECTRICAL SYSTEMS, available from the

American Society of Agricultural Engineers, 2950 Niles Road,

St. Joseph, MI 49085.

9. NFPA No. 30, FLAMMABLE AND COMBUSTIBLE LIQUIDS

CODE, available same as Item 1.

IMPORTANT SAFETY INSTRUCTIONS

Air-cooled Generators

DANGER



Only qualified electricians or contractors should

attempt such installations, which must comply

strictly with applicable codes, standards and regu-

lations.

1.1 UNPACKING/INSPECTION

After unpacking, carefully inspect the contents for damage.

This standby generator set is ready for installation with a factory •

supplied and pre-mounted base pad and has a weather protec-

tive enclosure that is intended for outdoor installation only.

This UL listed standby generator set may be packaged with an •

automatic transfer switch with built in load center. The combi-

nation transfer switch and load center is pre-wired with a two

foot and 30 foot conduit. Circuit breakers for emergency circuit

connections are included (if equipped).

This UL listed, 2-pole switch is rated at 100 • or 200 AC amperes

at 250 volts maximum. The 100 Amp transfer switch is for

indoor use only. The 200 Amp transfer switch is for indoor/

outdoor use (if equipped).



If this generator is used to power electrical load

circuits normally powered by a utility power

source, it is required by code to install a transfer

switch. The transfer switch must effectively isolate

the electrical system from the utility distribution

system when the generator is operating (NEC 700,

701 & 702). Failure to isolate an electrical system

by such means will result in damage to the gen-

erator and also may result in injury or death to

utility power workers due to backfeed of electrical

energy.

If any loss or damage is noted at time of delivery, have the

person(s) making the delivery note all damage on the freight bill

or affix their signature under the consignor's memo of loss or

damage.

If a loss or damage is noted after delivery, separate the damaged

materials and contact the carrier for claim procedures.

“Concealed damage” is understood to mean damage to the con-

tents of a package that is not in evidence at the time of delivery,

but is discovered later.

To properly open the roof, press down on the center top lip and

release the latch. If pressure is not applied from the top, the roof

may appear stuck. Always verify that the side lock is unlocked

before attempting to lift the roof.

1.2 PROTECTION SYSTEMS

Unlike an automobile engine, the generator may have to run for

long periods of time with no operator present to monitor engine

conditions. For that reason, the engine is equipped with the fol-

lowing systems that protect it against potentially damaging condi-

tions:

1. Low Oil Pressure Sensor

2. High Temperature Sensor

3. Overcrank

4. Overspeed

5. RPM Sensor

6. Low Battery

There are readouts on the control panel to notify personnel that

one of these failures has occurred. There is also a System Set LED

(single cylinder) or a Status message on the display (V-twins) that

displays when all of the conditions described in the "System Set

LED" section are true.

1.3 NEC REQUIREMENT FOR ARC FAULT

CIRCUIT INTERRUPTION BREAKER FOR

BEDROOMS

In 2001, the National Electric Code (NEC) introduced a requirement

for new construction. This new requirement indicates the need for

Arc Fault Circuit Interrupters to be used to protect the complete

branch circuit that feeds a dwelling bedroom. The actual NEC

requirement is indicated below.

1.3.1 SECTION 210.12 ARC FAULT CIRCUIT INTER- 

RUPTER PROTECTION

1. Definition: An arc fault circuit interrupter is a device intended

to provide protection from the effects of arc faults by recog-

nizing characteristics unique to arcing and by functioning to

de-energize the circuit when an arc fault is detected.

2. Dwelling Unit Bedrooms: All branch circuits that supply 125

volt, single-phase, 15 and 20 ampere outlets installed in

dwelling unit bedrooms shall be protected by an arc fault cir-

cuit interrupter listed to provide protection of the entire branch

circuit.

Section 210.12 requires that AFCI protection be provided on branch

circuits that supply outlets (receptacle, lighting, etc.) in dwell-

ing bedrooms. The requirement is limited to 15 and 20 ampere,

125 volt circuits. There is no prohibition against providing AFCI

protection on other circuits or in locations other than bedrooms.

Because circuits are often shared between a bedroom and other

areas such as closets and hallways, providing AFCI protection on

the complete circuit would comply with 210.12.

Section 1 — General Information

Air-cooled Generators

4

Section 1 — General Information

Air-cooled Generators

5

If during the installation of the home standby system the decision

is made to provide back up power to a bedroom branch circuit,

then the circuit breaker in the transfer switch should be replaced

with an Arc Fault Circuit Interrupter.

It is most important that breakers only be switched like for like.

For instance, if replacing a 15A breaker, it MUST be replaced with

a 15A AFCI breaker. Likewise, a 20A breaker MUST be replaced

with a 20A AFCI.

These AFCI breakers are available at the nearest hardware store.

Siemens Item # Description

Q115AF 15A Single Pole AFCI

Q120AF 20A Single Pole AFCI

1.4 EMISSION INFORMATION

The Environmental Protection Agency requires that this generator

complies with exhaust emission standards. This generator is certi-

fied to meet the applicable EPA emission levels. Additional infor-

mation regarding the requirements set by the EPA is as follows:

The generator is certified for use as a stationary engine for standby

power generation. Any other use may be a violation of federal

and/or local laws. It is important that to follow the maintenance

specifications in the "Maintenance" section to ensure that the

engine complies with the applicable emission standards for the

duration of the engine’s life. This engine is certified to operate on

Liquid Propane fuel and pipeline Natural Gas. The emission control

system on the generator consists of the following:

Fuel Metering System•

Carburetor/mixer assembly•

Fuel regulator•

Air Induction System•

Intake pipe/manifold•

Air cleaner•

Ignition System•

Spark plug•

Ignition module•

The Emissions Compliance Period referred to on the Emissions

Compliance Label indicates the number of operating hours for

which the engine has been shown to meet Federal emission

requirements. See the table below to determine the compliance

period for the generator. The displacement of the generator is listed

on the Emissions Compliance Label.

Displacement Category Compliance Period

< 66 cc

A 300 Hours

B 125 Hours

C 50 Hours

 66 cc -

< 225 cc

A 500 Hours

B 250 Hours

C 125 Hours

 225 cc

A 1000 Hours

B 500 Hours

C 250 Hours

6

Section 1 — General Information

Air-cooled Generators

1.5 THE GENERATOR

Data Label

(see sample)

Oil

Dipstick

Exhaust

Enclosure

Composite Base Oil Filter Battery Compartment

Fuel

Regulator

Fuel Inlet

(back)

Air Filter

Circuit

Breaker

Control

Panel

Data Label

(see sample)

Oil

Dipstick

Exhaust

Enclosure

Composite Base Oil Filter Battery Compartment

Fuel

Regulator

Fuel Inlet

(back)

Air Filter

Circuit

Breakers

Control

Panel

Figure 1.3 – 12, 14, 16, 17 and 20kW, V-twin,

GT-990/GT-999 Engine (door removed)

Figure 1.1 – 8kW, Single Cylinder, GH-410 Engine

(door removed)

Data Label

(see sample)

Oil

Dipstick

Exhaust

Enclosure

Composite Base Oil Filter Battery Compartment

Fuel

Regulator

Fuel Inlet

(back)

Air

Filter

Circuit

Breaker

Control

Panel

Figure 1.2 – 10kW, V-twin, GT-530 Engine

(door removed)

Data Label Sample

7

Section 1 — General Information

Air-cooled Generators

1.6 SPECIFICATIONS

1.6.1 GENERATOR 

Model 8kW 10kW 12kW 14kW 16kW 17kW 20kW

Rated Maximum

Power Capacity (Watts*)

7,000 NG

8,000 LP

9,000 NG

10,000 LP

12,000 NG

12,000 LP

13,000 NG

14,000 LP

16,000 NG

16,000 LP

16,000 NG

17,000 LP

18,000 NG

20,000 LP

Rated Voltage 120/240

Rated Maximum Load Current (Amps)

120 Volts** (NG/LP) 58.3/66.6 75.0/83.3 100.0/100.0 108.3/116.6 133.3/133.3 133.3/141.6 150.0/166.6

240 Volts (NG/LP) 29.2/33.3 37.5/41.6 50.0/50.0 54.2/58.3 66.6/66.6 66.6/70.8 75.0/83.3

Main Circuit Breaker 35 Amp 45 Amp 50 Amp 60 Amp 65 Amp 65 Amp 100 Amp

Circuits*** 50A, 240V - - - 1 1 1 -

40A, 240V - - 1 1 1 1 -

30A, 240V 1 1 1 - - - -

20A, 240V - 1 - 1 1 1 -

20A, 120V 1 3 3 4 5 5 -

15A, 120V 5 3 5 4 5 5 -

Phase 1

Number of Rotor Poles 2

Rated AC Frequency 60 Hz

Battery Requirement

Group 26R, 12

Volts and 350 CCA

Minimum

Group 26R, 12 Volts and 525 CCA Minimum

Weight (unit only in lbs.) 340 387 439 439 439 455/421 450

Enclosure Steel Steel Steel Steel Steel Steel/Aluminum Aluminum

Normal Operating Range -20° F (-28.8° C) to 77° F (25° C)

* Maximum wattage and current are subject to and limited by such factors as fuel Btu content, ambient temperature, altitude, engine power and condition, etc. Maximum power decreases about

3.5 percent for each 1,000 feet above sea level; and also will decrease about 1 percent for each 6 C (10 F) above 16 C (60 F) ambient temperature.

** Load current values shown for 120 volts are maximum TOTAL values for two separate circuits. The maximum current in each circuit must not exceed the value stated for the 240 volts.

*** Circuits to be moved must be protected by same size breaker. For example, a 15 amp circuit in the main panel must be a 15 amp circuit in the transfer switch.

1.6.2 ENGINE 

Model 8 kW 10 kW 12/14/16/17 kW 20 kW

Type of Engine GH-410 GT-530 GT-990 GT-999

Number of Cylinders 1 2 2 2

Rated Horsepower @ 3,600 rpm 14.8 18 32 36

Displacement 410cc 530cc 992cc 999cc

Cylinder Block Aluminum w/Cast Iron Sleeve

Valve Arrangement Overhead Valves

Ignition System Solid-state w/Magneto

Recommended Spark Plug RC14YC BPR6HS RC14YC RC12YC

Spark Plug Gap 0.76 mm (0.030 inch) 0.76 mm (0.030 inch) 1.02 mm (0.040 inch) 0.76 mm (0.030 inch)

Compression Ratio 8.6:1 9.5:1 9.5:1 9.5:1

Starter 12 VDC

Oil Capacity Including Filter Approx. 1.5 Qts Approx. 1.7 Qts Approx. 1.7 Qts Approx. 1.7 Qts

Recommended Oil Filter Part # 070185F

Recommended Air Filter Part # 0G3332 Part # 0E9581 Part # 0C8127 Part # 0G5894

Operating RPM 3,600

1.7 SYSTEM SET LED

The “System Set” LED (single cylinder) or "Ready to Run" on the

display (v-twin) is ready when all of the following conditions are

true:

1. The AUTO/OFF/MANUAL switch is set to the AUTO position.

2. The utility voltage being supplied to the unit is being sensed

by the PCB. If the utility sense voltage is not connected to the

unit or if it is below approximately 150-160 volts AC, then the

system set light will flash rapidly (8kW). This indicates that if

the AUTO/OFF/MANUAL switch is placed in the Auto position,

the generator will start.

3. No alarms are present, for example, low oil pressure, high

temperature, etc.

1.8 FUEL REQUIREMENTS

AND RECOMMENDATIONS

With LP gas, use only the vapor withdrawal system. This type of

system uses the vapors formed above the liquid fuel in the storage

tank.

The engine has been fitted with a fuel carburetion system that

meets the specifications of the 1997 California Air Resources

Board for tamper-proof dual fuel systems. The unit will run on

natural gas or LP gas, but it has been factory set to run on natural

gas. Should the primary fuel need to be changed to LP gas, the

fuel system needs to be reconfigured. See the reconfiguring the

Fuel System section for instructions on reconfiguration of the fuel

system.

Recommended fuels should have a Btu content of at least 1,000

Btus per cubic foot for natural gas; or at least 2,520 Btus per

cubic foot for LP gas. Ask the fuel supplier for the Btu content of

the fuel.

Required fuel pressure for natural gas is five (5) inches to seven

(7) inches water column (0.18 to 0.25 psi); and for liquid pro-

pane, 10 inches to 12 inches of water column (0.36 to 0.43 psi).

The primary regulator for the propane supply is NOT INCLUDED

with the generator.

NOTE:

All pipe sizing, construction and layout must comply with NFPA

54 for natural gas applications and NFPA 58 for liquid propane

applications. Once the generator is installed, verify that the fuel

pressure NEVER drops below four (4) inches water column for

natural gas or 10 inches water column for liquid propane.

Prior to installation of the generator, the installer should consult

local fuel suppliers or the fire marshal to check codes and regula-

tions for proper installation. Local codes will mandate correct rout-

ing of gaseous fuel line piping around gardens, shrubs and other

landscaping to prevent any damage.

Special considerations should be given when installing the unit

where local conditions include flooding, tornados, hurricanes,

earthquakes and unstable ground for the flexibility and strength of

piping and their connections.

Use an approved pipe sealant or joint compound on all threaded

fitting.

All installed gaseous fuel piping must be purged and leak tested

prior to initial start-up in accordance with local codes, standards

and regulations.

1.9 FUEL CONSUMPTION

Unit

Nat. Gas LP Vapor

1/2 Load Full Load 1/2 Load Full Load

7/8 kW 77 140 0.94/34 1.68/62

9/10 kW 102 156 1.25/46 1.93/70

12/12 kW 152 215 1.53/56 2.08/76

13/14 kW 156 220 1.56/58 2.30/84

16/16 kW 183 261 1.59/58 2.51/91

16/17 kW 183 261 1.61/59 2.57/94

18/20 kW 206 294 1.89/69 2.90/106

* Natural gas is in cubic feet per hour.

** LP is in gallons per hour/cubic feet per hour.

*** Values given are approximate.

Verify that gas meter is capable of providing enough fuel flow to

include household appliances.

1.9.1 BTU FLOW REQUIREMENTS - 

NATURAL GAS

BTU flow required for each unit based on 1000 BTU per cubic

foot.

7kW — 140,000 BTU/Hour•

9kW — 156,000 BTU/Hour•

12kW — 215,000 BTU/Hour•

13kW — 220,000 BTU/Hour•

16kW — 261,000 BTU/Hour•

18kW — 294,000 BTU/Hour•

DANGER



Gaseous fuels such as natural gas and liquid

propane (LP) gas are highly explosive. Even the

slightest spark can ignite such fuels and cause

an explosion. No leakage of fuel is permitted.

Natural gas, which is lighter than air, tends to

collect in high areas. LP gas is heavier than air

and tends to settle in low areas.

NOTE:

A minimum of one approved manual shut-off valve must be

installed in the gaseous fuel supply line. The valve must be eas-

ily accessible. Local codes determine the proper location.

Section 1 — General Information

Air-cooled Generators

8

9

1.10 RECONFIGURING THE

FUEL SYSTEM

1.10.1 8 KW, 410CC ENGINE 

To reconfigure the fuel system from NG to LP, follow these steps

(Figure 1.4):

NOTE:

The primary regulator for the propane supply is NOT INCLUDED

with the generator. A fuel pressure of 10 to 12 inches of water

column (0.36 to 0.43 psi) to the fuel inlet of the generator MUST

BE SUPPLIED.

1. Turn off the main gas supply (if connected).

2. Open the roof and remove the door.

3. Remove the battery (if installed).

4. Take the plastic T-handle fuel selector in the poly bag supplied

with the generator.

5. Locate the selector knob on the air box cover, behind the

yellow air filter door and power bulge. The unit comes from

the factory in the NG (Natural Gas) position. Grasping the

T-handle, insert the pin end into the hole in the selector knob

and pull out to overcome spring pressure and then twist

clockwise 90 degrees and allow the selector to return in once

aligned with the LP (Liquid Propane) position.

6. Save this tool with the Owner's Manual.

7. Install the battery, door and close the roof.

8. Reverse the procedure to convert back to natural gas.

Figure 1.4 – Fuel Selector

NOTE:

Use an approved pipe sealant or joint compound on all threaded

fittings to reduce the possibility of leakage.

1.10.2 10, 12, 14, 16, 17 AND 20KW, V-TWIN 

ENGINES

To reconfigure the fuel system from NG to LP, follow these steps:

NOTE:

The primary regulator for the propane supply is NOT INCLUDED

with the generator. A fuel pressure of 10 to 12 inches of water

column (0.36 to 0.43 psi) to the fuel inlet of the generator MUST

BE SUPPLIED.

1. Open the roof.

2. For 10kW units: Loosen clamp and slide back the air inlet

hose.

Slide fuel selector on carburetor out towards the back of the •

enclosure (Figures 1.5 and 1.6).

Return the inlet hose and tighten clamp securely.•

For 12, 14, 16, 17 and 20kW units: remove the air cleaner

cover.

Slide the selector lever out towards the back of the enclosure •

(Figures 1.7 and 1.8).

Return the air cleaner cover and tighten the two thumb •

screws.

Figure 1.5 - 10kW, GT-530 (Inlet Hose Slid Back)

Fuel Selection

Lever - "In"

Position for

Natural Gas

Fuel

Figure 1.6 - 10kW, GT-530 (Inlet Hose Slid Back)

Fuel Selection

Lever - "Out"

Position for

Liquid Propane

(Vapor) Fuel

Section 1 — General Information

Air-cooled Generators

10

3. Close the roof.

4. Reverse the procedure to convert back to natural gas.

Figure 1.7 - 12, 14, 16, 17, & 20kW,

GT-990/GT-999 (Airbox Cover Removed)

Fuel Selection Lever - "In" Position for Natural Gas Fuel

Figure 1.8 - 12, 14, 16, 17, & 20kW,

GT-990/GT-999 (Airbox Cover Removed)

Fuel Selection Lever - "Out" Position for Liquid Propane

(Vapor) Fuel

1.11 LOCATION

DANGER



The engine exhaust fumes contain carbon mon-

oxide, which can be DEADLY. This dangerous

gas, if breathed in sufficient concentrations,

can cause unconsciousness or even death. This

generator must be installed properly, in strict

compliance with applicable codes and stan-

dards. Following installation, do nothing that

might render the system unsafe or in noncom-

pliance with such codes and standards.

• Operate the generator outdoors ONLY.

• Keep exhaust gases from entering a confined

area through windows, doors, ventilation, crawl

spaces or other openings (Figure 1.9).

• Generac Power Systems as a responsible manu-

facturer highly recommends that carbon monox-

ide detector(s) be installed indoors according to

the manufacturer's instructions/recommendations.

• The generator must me mounted safely per appli-

cable codes and the manufacturer's specifica-

tions. Do NOT alter or add to the exhaust system,

or do anything that might render the exhaust sys-

tem unsafe or in noncompliance with applicable

codes and standards.

1.11.1 GENERATOR 

Install the generator set, in its protective enclosure, outdoors,

where adequate cooling and ventilating air is always available

(Figure 1.9). Consider these factors:

The installation of the generator • must comply strictly with

NFPA 37, NFPA 54, NFPA 58, and NFPA 70 standards.

Install the unit where air inlet and outlet openings will not •

become obstructed by leaves, grass, snow, etc.. If prevailing

winds will cause blowing or drifting, consider using a wind-

break to protect the unit.

Install the generator on high ground where water levels will not •

rise and endanger it.

Allow sufficient room on all sides of the generator for mainte-•

nance and servicing. This unit must be installed in accordance

with current applicable NFPA 37 and NFPA 70 standards; as

well as any other federal, state and local codes for minimum

distances from other structures. DO NOT install under wooden

decks or structures unless there is at least four (4) feet of clear-

ance above the generator, three (3) feet of clearance on sides

and front, and 18 inches of clearance at back of unit.

Install the unit where rain gutter down spouts, roof run-off, •

landscape irrigation, water sprinklers or sump pump discharge

does not flood the unit or spray the enclosure, including any air

inlet or outlet openings.

Install the unit where services will not be affected or obstructed, •

including concealed, underground or covered services such as

electrical, fuel, phone, air conditioning or irrigation.

Where strong prevailing winds blow from one direction, face the •

generator air inlet openings to the prevailing winds.

Install the generator as close as possible to the fuel supply, to •

reduce the length of piping.

Install the generator as close as possible to the transfer switch. •

REMEMBER THAT LAWS OR CODES MAY REGULATE THE

DISTANCE AND LOCATION.

The genset must be installed on a level surface. The base frame •

must be level within two (2) inches all around.

The generator is typically placed on pea gravel or crushed •

stone. Check local codes if a concrete slab is required. If a

concrete base slab is required, all federal, state and local codes

should be followed. Special attention should be given to the

concrete base slab which should exceed the length and width

of the generator by a minimum of six (6) inches (0.152 meters)

on all sides.

Section 1 — General Information

Air-cooled Generators

11

Figure 1.9 – Generator Clearances

1.11.2 NEW INSTALLATION GUIDELINES FOR 

STATIONARY AIR-COOLED 8, 10, 12, 14, 16,

17 AND 20 KW GENERATORS.

The National Fire Protection Association has a standard for the

installation and use of stationary combustion engines. That

standard is NFPA 37 and its requirements limit the spacing of an

enclosed generator set from a structure or wall (Figure 1.10).

NFPA 37, Section 4.1.4, Engines Located Outdoors. Engines, and

their weatherproof housings if provided, that are installed outdoors

shall be located at least 5 ft. from openings in walls and at least 5

ft. from structures having combustible walls. A minimum separa-

tion shall not be required where the following conditions exist:

1. The adjacent wall of the structure has a fire resistance rating

of at least 1 hour.

2. The weatherproof enclosure is constructed of noncombus-

tible materials and it has been demonstrated that a fire within

the enclosure will not ignite combustible materials outside the

enclosure.

Annex A — Explanatory Material

A4.1.4 (2) Means of demonstrating compliance are by means

of full scale fire test or by calculation procedures.

Because of the limited spaces that are frequently available for

installation, it has become apparent that exception (2) would be

beneficial for many residential and commercial installations. With

that in mind, the manufacturer contracted with an independent

testing laboratory to run full scale fire tests to assure that the

Carrier enclosure would not ignite combustible materials outside

the enclosure.

The criteria was to determine the worst case fire scenario within

the generator and to determine the ignitability of items outside

the engine enclosure at various distances. The Carrier enclosure

is constructed of non-combustible materials and the results and

conclusions from the independent testing lab indicated that any

fire within the generator enclosure would not pose any ignition risk

to nearby combustibles or structures, with or without fire service

personnel response.

Based on this testing and the requirements of NFPA 37, Sec 4.1.4,

the guidelines for installation of the generators listed above are

changed to 18 inches (457mm) from the back side of the genera-

tor to a stationary wall or building. For adequate maintenance and

airflow clearance, the area above the generator should be at least

4 feet with a minimum of 3 feet at the front and ends of the enclo-

sure. This would include trees, shrubs and vegetation that could

obstruct airflow. See the diagram on the reverse of this page and

the installation drawing within the owner’s manual for details.

Generator exhaust contains DEADLY carbon monoxide gas. This

dangerous gas can cause unconsciousness or death. Do not place

the unit near windows, doors, fresh air intakes (furnaces, etc.) or

any openings in the building or structure, including windows and

doors of an attached garage.

1.11.3 TRANSFER SWITCH (  if included)

1.11.3.1 8, 10, 12, 14, 16, 17 and 20kW Units 

(if equipped)

The transfer switch that may have shipped inside the carton with

the 8, 10, 12, 14, 16 or 17kW generator is enclosed in a NEMA

1 (indoor rated only) enclosure. The transfer switch that may

have shipped with the 20kW generator is enclosed in a NEMA 3R

(indoor/outdoor rated) enclosure.

Install the transfer switch indoors on a firm, sturdy supporting •

structure.

To prevent switch distortion, level the switch if necessary. This •

can be done by placing washers between the switch enclosure

and mounting surface.

Never install the switch where water or any corrosive substance •

might drip onto the enclosure.

Protect the switch at all times against excessive moisture, dust, •

dirt, lint, construction grit and corrosive vapors.



If the AUTO/OFF/MANUAL switch is not set to its

OFF position, the generator can crank and start

as soon as the battery cables are connected. If

the utility power supply is not turned off, spark-

ing can occur at the battery posts and cause an

explosion.

1.12 BATTERY REQUIREMENTS

See the Specifications section for correct battery size and rating.

Section 1 — General Information

Air-cooled Generators

12

Section 1 — General Information

Air-cooled Generators

Figure 1.10 – Installation Guidelines

18 inches

Minimum Distance

36 inches

60 inches 60 inches

Existing Wall

No windows or openings in the wall permitted

within 5 feet from any point of the generator.

Top of Generator

48” Minimum

60” Recommended

Minimum From Ends

18 inches

Minimum

Generator

Clearance from windows,

doors, any openings in the

wall, shrubs or vegetation

over 12” in height

Clearance from the ends and front of the

generator should be 36 inches. This

would include shrubs, trees and any

kind of vegetation. Clearance at the top

should be a minimum of 48 inches from

any structure, overhang or projections

from the wall. The generator should not

be placed under a deck or other

structure that is closed in and would limit

or contain air flow.

These guidelines are based upon fire

testing of the generator enclosure and

the manufacturer’s requirement for air

flow for proper operation. Local codes

may be different and more restrictive

than what is described here.

This drawing supersedes installation instructions in all Carrier air-cooled installation and owner’s manuals dated

previous to May 26, 2007.

13

1.13 BATTERY INSTALLATION

Fill the battery with the proper electrolyte fluid if necessary and

have the battery fully charged before installing it.

Before installing and connecting the battery, complete the follow-

ing steps:

1. Set the generator's AUTO/OFF/MANUAL switch to OFF.

2. Turn off utility power supply to the transfer switch.

3. Remove the 7.5A fuse from the generator control panel.

Battery cables were factory connected at the generator (Figure

1.10). Connect cables to battery posts as follows:

4. Connect the red battery cable (from starter contactor) to the

battery post indicated by a positive, POS or (+).

5. Connect the black battery cable (from frame ground) to the

battery post indicated by a negative, NEG or (—).

Figure 1.10 – Battery Cable Connections

NOTE:

Dielectric grease should be used on battery posts to aid in the

prevention of corrosion.

NOTE:

Damage will result if battery connections are made in reverse.

NOTE:

In areas where temperatures regularly fall below 10° F (-12° C)

it is recommended that a pad type battery heater be installed to

aid in cold climate starting.

1.14 THE BATTERY

DANGER



Do not dispose of the battery in a fire. The

battery is capable of exploding.



A battery presents a risk of electrical shock

and high short circuit current. The following pre-

cautions are to be observed when working on

batteries:

• Remove the 7.5A fuse from the generator control

panel.

• Remove watches, rings or other metal objects;

• Use tools with insulated handles;

• Wear rubber gloves and boots;

• Do not lay tools or metal parts on top of the

battery; and

• Disconnect charging source prior to connecting or

disconnecting battery terminals.



Do not open or mutilate the battery. Released

electrolyte has been known to be harmful to the

skin and eyes, and to be toxic.



The electrolyte is a dilute sulfuric acid that is

harmful to the skin and eyes. It is electrically

conductive and corrosive.

The following procedures are to be observed:

• Wear full eye protection and protective clothing;

• Where electrolyte contacts the skin, wash it off

immediately with water;

• Where electrolyte contacts the eyes, flush thor-

oughly and immediately with water and seek medi-

cal attention; and

• Spilled electrolyte is to be washed down with an

acid neutralizing agent. A common practice is to

use a solution of 1 pound (500 grams) bicarbonate

of soda to 1 gallon (4 liters) of water. The bicar-

bonate of soda solution is to be added until the

evidence of reaction (foaming) has ceased. The

resulting liquid is to be flushed with water and the

area dried.



Lead-acid batteries present a risk of fire

because they generate hydrogen gas. The fol-

lowing

procedures are to be followed:

• DO NOT SMOKE when near the battery;

• DO NOT cause flame or spark in battery area; and

• Discharge static electricity from body before

touching the battery by first touching a grounded

metal surface.



Be sure the AUTO/OFF/MANUAL switch is set to

the OFF position before connecting the battery

cables. If the switch is set to AUTO or MANUAL,

the generator can crank and start as soon as

the battery cables are connected.

Section 1 — General Information

Air-cooled Generators

14



Be sure the utility power supply is turned off

and the 7.5A fuse is removed from the generator

control panel, or sparking may occur at the bat-

tery posts as the cables are attached and cause

an explosion.

Servicing of the battery is to be performed or supervised by per-

sonnel knowledgeable of batteries and the required precautions.

Keep unauthorized personnel away from batteries.

See the Specifications section for the correct size and rating when

replacing the battery. Have these procedures performed at the

intervals specified in the “Service Schedule.” A negative ground

system is used. Battery connections are shown on the wiring dia-

grams. Make sure the battery is correctly connected and terminals

are tight. Observe battery polarity when connecting the battery to

the generator set.

1.15 BATTERY CHARGER

NOTE:

These generators DO NOT contain an internal battery charger.

NOTE:

The manufacturer provides a battery trickle charger that is

active when the unit is set up for automatic operation. With

the battery installed and utility power source voltage available

to the transfer switch, the battery receives a trickle charge to

prevent self-discharge. The trickle charger is designed to help

extend the life of the battery by maintaining the battery. The

trickle charge feature cannot be used to recharge a discharged

battery.

For units shipped with a transfer switch/load center, the battery

charger is pre-installed in the transfer switch enclosure.

For units shipped without a transfer switch/load center, a separate

battery charger module is included with the generator.

(For battery charger installation, see the Generator Install Guidelines

and Battery Charger Instructions included with the unit.)

2.1 BEFORE INITIAL START-UP

NOTE:

These units have been run and tested at the factory prior to

being shipped and do not require any type of break-in.

NOTE:

This unit comes filled with oil from the factory. Check the oil

level and add the appropriate amount if necessary.

Before starting, complete the following:

1. Set the generator’s main circuit breaker to its OFF (or OPEN)

position.

2. Set the generator's AUTO/OFF/MANUAL switch to the OFF

position.

3. Turn OFF all breakers on the load center of the transfer box (T1

and T2).

4. Turn OFF all loads connected to the transfer switch terminals

T1 and T2.

5. Check the engine crankcase oil level and, if necessary, fill to

the dipstick FULL mark with the recommended oil. Do not fill

above the FULL mark.

6. Check the fuel supply. Gaseous fuel lines must have been

properly purged and leak tested in accordance with applicable

fuel-gas codes. All fuel shutoff valves in the fuel supply lines

must be open.

During initial start up only, the generator may exceed the normal

number of start attempts and experience an “over crank” fault (See

the "Overcrank" section). This is due to accumulated air in the fuel

system during installation. Reset the control board and restart up

to two more times, if necessary. If unit fails to start, contact the

local dealer for assistance.



Never operate the engine with the oil level

below the “Add” mark on the dipstick. Doing this

could damage the engine.

2.2 CHECK TRANSFER SWITCH

OPERATION

Refer to the "Manual Transfer Operation" section, of the owner’s

manual for procedures.

DANGER



Do not attempt manual transfer switch operation

until all power voltage supplies to the transfer

switch have been positively turned off. Failure to

turn off all power voltage supplies will result in

extremely hazardous and possibly fatal electri-

cal shock.

2.3 ELECTRICAL CHECKS

Complete electrical checks as follows:

1. Set the generator's main circuit breaker to its OFF (or OPEN)

position.

2. Set the generator's AUTO/OFF/MANUAL switch to the OFF

position.

3. Turn OFF all breakers on the load center of the transfer box (T1

and T2).

4. Turn on the utility power supply to the transfer switch using

the means provided (such as a utility main line circuit break-

er).

DANGER



The transfer switch is now electrically “hot.”

Contact with “hot” parts will result in extremely

hazardous and possibly fatal electrical shock.

Proceed with caution.

5. Use an accurate AC voltmeter to check utility power source

voltage across transfer switch terminals N1 and N2. Nominal

line-to-line voltage should be 240 volts AC.

Section 2 — Post Installation Start-up and Adjustments

Air-cooled Generators

15

6. Check utility power source voltage across terminals N1 and

the transfer switch neutral lug; then across terminal N2 and

neutral. Nominal line-to-neutral voltage should be 120 volts

AC.

7. When certain that utility supply voltage is compatible with

transfer switch and load circuit ratings, turn OFF the utility

power supply to the transfer switch.

8. On the generator panel, set the Auto/Off/ Manual switch to

MANUAL. The engine should crank and start.

9. Let the engine warm up for about five minutes to allow inter-

nal temperatures to stabilize. Then, set the generator’s main

circuit breaker to its ON (or closed) position.

DANGER



Proceed with caution! Generator power voltage

is now supplied to the transfer switch. Contact

with live transfer switch parts will result in dan-

gerous and possibly fatal electrical shock.

10. Connect an accurate AC voltmeter and a frequency meter

across transfer switch terminal lugs E1 and E2. 8kW voltage

should be 230-240 volts at a frequency of 61-63 Hertz. 12,

14, 16, 17 and 20kW voltage should be 247-249 at a fre-

quency of 59.5-60.5 Hertz. 10kW voltage should be 220-230

volts at a frequency of 59.5-60.5 Hertz.

11. Connect the AC voltmeter test leads across terminal lugs E1

and neutral; then across E2 and neutral. In both cases, volt-

age reading should be 121-126 volts AC (8kW), and 125-126

volts AC (10, 12, 14, 16, 17 and 20kW).

12. Set the generator’s main circuit breaker to its OFF (or OPEN)

position. Let the engine run at no-load for a few minutes to

stabilize internal engine generator temperatures.

13. Set the generator's AUTO/OFF/MANUAL switch to OFF. The

engine should shut down.

NOTE:

It is important not to proceed until certain that generator AC

voltage and frequency are correct and within the stated limits.

Generally, if both AC frequency and voltage are high or low,

the engine governor requires adjustment* (*GH410 only). If

frequency is correct, but voltage is high or low, the generator’s

voltage regulator requires adjustment.

2.4 GENERATOR TESTS UNDER LOAD

To test the generator set with electrical loads applied, proceed as

follows:

1. Set generator’s main circuit breaker to its OFF (or OPEN) posi-

tion.

2. Turn OFF all breakers on the load center of the transfer box (T1

and T2).

3. Set the generator's AUTO/OFF/MANUAL switch to OFF.

4. Turn OFF the utility power supply to the transfer switch,

using the means provided (such as a utility main line circuit

breaker).



Do not attempt manual transfer switch operation

until all power voltage supplies to the transfer

switch have been positively turned off. Failure to

turn off all power voltage supplies will result in

extremely hazardous and possibly fatal electri-

cal shock.

5. Manually set the transfer switch to the STANDBY position, i.e.,

load terminals connected to the generator's E1/E2 terminals.

The transfer switch operating lever should be down.

6. Set the generator's AUTO/OFF/MANUAL switch to MANUAL.

The engine should crank and start immediately.

7. Let the engine stabilize and warm up for a few minutes.

8. Set the generator’s main circuit breaker to its ON (or CLOSED)

position. Loads are now powered by the standby generator.

9. Turn ON the load center of the transfer switch (T1 and T2).

10. Connect an accurate AC voltmeter and a frequency meter

across terminal lugs E1 and E2.

8kW voltage should be greater than 230 volts and frequency •

should be greater than 58 Hz.

10, • 12, 14, 16, 17 and 20kW voltage should be greater than

240 volts and frequency should be 60 Hz.

11. Let the generator run at full rated load for 20-30 minutes.

Listen for unusual noises, vibration or other indications of

abnormal operation. Check for oil leaks, evidence of overheat-

ing, etc.

12. When testing under load is complete, turn OFF electrical

loads.

13. Set the generator's main circuit breaker to its OFF (or OPEN)

position.

14. Let the engine run at no-load for a few minutes.

15. Set the AUTO/OFF/MANUAL switch to OFF. The engine should

shut down.

2.5 CHECKING AUTOMATIC

OPERATION

To check the system for proper automatic operation, proceed as

follows:

1. Set generator’s main circuit breaker to its OFF (or OPEN) posi-

tion.

2. Check that the AUTO/OFF/MANUAL switch is set to OFF.

3. Turn OFF the utility power supply to the transfer switch, using

means provided (such as a utility main line circuit breaker).

4. Manually set the transfer switch to the UTILITY position, i.e.,

load terminals connected to the utility power source side.

5. Turn ON the utility power supply to the transfer switch,

using the means provided (such as a utility main line circuit

breaker).

6. Set the generator's main circuit breaker to its ON (or CLOSED)

position.

7. Set the AUTO/OFF/MANUAL switch to AUTO. The system is

now ready for automatic operation.

Section 2 — Post Installation Start-up and Adjustments

Air-cooled Generators

16

8. Turn OFF the utility power supply to the transfer switch.

With the AUTO/OFF/MANUAL switch at AUTO, the engine should

crank and start when the utility source power is turned OFF after

a 10 second delay. After starting, the transfer switch should

connect load circuits to the standby side after a five (5) second

delay. Let the system go through its entire automatic sequence of

operation.

With the generator running and loads powered by generator AC

output, turn ON the utility power supply to the transfer switch. The

following should occur:

After about 15 seconds, the switch should transfer loads back •

to the utility power source.

About one minute after re-transfer, the engine should shut •

down.

2.6 ENGINE GOVERNOR ADJUSTMENT

If both AC frequency and voltage are correspondingly high or low,

adjust the engine governor as follows:

2.6.1 8 KW UNITS 



The engine must be OFF to perform steps 1 and

2.

1. Loosen the governor clamp bolt (Figure 2.1).

2. Hold the governor lever at its wide open throttle position

(clockwise), and rotate the governor shaft clockwise as far

as it will go. Then, tighten the governor lever clamp bolt to 70

inch-pounds (8 N-m).

3. Start the generator; let it stabilize and warm up at no-load.

4. Connect a frequency meter across the generators AC output

leads.

Figure 2.1 — Engine Governor Adjustment

Single Cylinder Engines

GOVERNOR

SHAFT

PRIMARY

ADJUST

SCREW

GOVERNOR

CLAMP

BOLT

SECONDARY

ADJUST SCREW

5. Turn the primary adjust screw to obtain a frequency reading

of 61.5 Hertz. Turn the secondary adjust screw to obtain a

frequency of 62.5 Hz.

2.6.2 12, 14, 16, 17 & 20KW UNITS 

NOTE:

All V-twin units DO NOT require an engine governor adjustment

due to their design.

2.6.3 ADDITIONAL CORROSION 

PROTECTION

Periodically spray all engine linkage parts and brackets with corro-

sion inhibiting spray such as WD-40 or a comparable product.

2.7 VOLTAGE REGULATOR

ADJUSTMENT

2.7.1 8 & 10KW UNITS 

Due to the brushless design of these two alternators, no voltage

regulator is used and therefore no voltage adjustment is required.

2.7.2 12,  14, 16, 17 & 20KW UNITS

With the frequency between 59.5 -60.5 Hertz at no-load, slowly

turn the slotted potentiometer (Figure 2.2) until line voltage reads

247-249 volts.

Figure 2.2 – Voltage Adjustment Potentiometer

Turn to

adjust voltage.

NOTE:

The access panel on top of the control panel must be removed

to adjust the voltage regulator.

NOTE:

The voltage regulator is housed behind the generator's control

panel. The regulator maintains a voltage in direct proportion to

frequency at a 2-to-1 ratio. For example, at 60 Hertz, line-to-

neutral voltage will be 124 volts.

Section 2 — Post Installation Start-up and Adjustments

Air-cooled Generators

17

Section 3 — Operation

Air-cooled Generators

3.1 CONTROL PANEL INTERFACE

3.1.1 USING THE AUTO/OFF/MANUAL SWITCH 

(FIGURES 3.1 & 3.2)



With the switch set to AUTO, the engine may

crank and start at any time without warning.

Such automatic starting occurs when utility

power source voltage droops below a preset

level or during the normal exercise cycle. To

prevent possible injury that might be caused

by such sudden starts, always set the switch to

OFF and remove the fuses before working on or

around the generator or transfer switch. Then,

place a “DO NOT OPERATE” tag on the genera-

tor panel and on the transfer switch.

1. “AUTO” Position – Selecting this switch activates fully auto-

matic system operation. It also allows the unit to automati-

cally start and exercise the engine every seven days with the

setting of the exercise timer (see the Setting the Exercise

Timer section).

2. “OFF” Position – This switch position shuts down the engine.

This position also prevents automatic operation.

3. “MANUAL” Position – Set the switch to MANUAL to crank

and start the engine. Transfer to standby power will not occur

unless there is a utility failure.

Figure 3.1 – 8kW Generator Control Panel

SET

EXERCISE

SYSTEM READY

LOW BATTERY

LOW OIL PRESSURE

HIGH OIL TEMPERATURE

OVERSPEED

RPM SENSOR LOSS

OVERCRANK

Figure 3.2 – 10/12/14/16/17 & 20kW Generator

Control Panel

ENTER

ECS

3.1.2 SETTING THE EXERCISE TIMER 

This generator is equipped with an exercise timer. Once it is set,

the generator will start and exercise every seven days, on the day

of the week and at the time of day specified. During this exercise

period, the unit runs for approximately 12 minutes and then shuts

down. Transfer of loads to the generator output does not occur

during the exercise cycle unless utility power is lost.

8kW 

A switch on the control panel (see Figure 3.1) permits selection of

the day and time for the system to exercise. At the chosen time,

perform the following sequence to select the desired day and time

of day the system will exercise. Remember seasonal time changes

affect the exercise settings.

1. Verify that the AUTO/OFF/MANUAL switch is set to AUTO.

2. Press and hold the “Set Exercise” switch for several seconds.

All the red LED’s will stop flashing immediately and the gen-

erator will start.

3. The generator will start and run for approximately 12 minutes

and then shut down. The exerciser is now set to run at this

time of day each week.

Example: If the “Set Exercise” pressed on Saturday afternoon at

2:00 p.m., the generator will start and exercise for approximately

12 minutes every Saturday at 2:00 p.m.

NOTE:

The exerciser will only work in the AUTO mode and will not work

unless this procedure is performed. The exerciser will need to

be reset every time the 12 volt battery is disconnected and then

reconnected, and when the fuse is removed and/or replaced.

18

10 to 20 KW - INSTALLATION ASSISTANT 

Interconnect System Self Test Feature (follow the on-screen

prompts)

Upon power up, this controller will go through a system self test

which will check for the presence of utility voltage on the DC

circuits. This is done to prevent damage if the installer mistakenly

connects AC utility power sense wires into the DC terminal block.

If utility voltage is detected, the controller will display a warning

message and lock out the generator, preventing damage to the

controller. Power to the controller must be removed to clear this

warning.

Utility voltage must be turned on and present at the N1 and N2

terminals inside the generator control panel for this test to be

performed and pass.

NOTE:

DAMAGE CAUSED BY MISWIRING OF THE INTERCONNECT

WIRES IS NOT WARRANTABLE!

This test will be performed each time the controller is powered

up.

Upon first power up of the generator, the display interface will

begin an installation assistant. The assistant will prompt the user

to set the minimum settings to operate. These settings are sim-

ply: Current Date/Time and Exercise Day/Time. The maintenance

intervals will be initialized when the exercise time is entered (Figure

3.2).

The exercise settings can be changed at any time via the "EDIT"

menu (see Appendix, "Menu System").

If the 12 volt battery is disconnected or the fuse removed, the

Installation Assistant will operate upon power restoration. The

only difference is the display will only prompt the customer for the

current Time and Date.

IF THE INSTALLER TESTS THE GENERATOR PRIOR TO

INSTALLATION, PRESS THE “ENTER” KEY TO AVOID SETTING

UP THE EXERCISE TIME. THIS WILL ENSURE THAT WHEN

THE CUSTOMER POWERS UP THE UNIT, HE WILL STILL BE

PROMPTED TO ENTER AN EXERCISE TIME.

NOTE:

The exerciser will only work in the AUTO mode and will not work

unless this procedure is performed. The current date/time will

need to be reset every time the 12 volt battery is disconnected

and then reconnected, and/or when the fuse is removed.

3.1.3 DISPLAY INTERFACE 

8 kW LED Display 

Seven (7) LED’s are provided for user status indications. The LED

functions are:

1. System Ready (green)

2. Low Battery (red)

3. Low Oil Pressure (red)

4. High Oil Temperature (red)

5. Over Speed (red)

6. RPM Sensor Loss (red)

7. Over Crank (red)

See the Protection Systems section for details.

10 to 20KW DISPLAY INTERFACE MENUS 

The LCD display is organized as detailed below:

The “Home” page, this page is the default page which will be •

displayed if no keys are pressed for 30 seconds. This page

normally shows the current Status message and the current

date and time. The highest priority active Alarm and/or Warning

will be automatically posted on this page as well as flashing

the backlight when such an event is detected. In the case of

multiple Alarms or Warnings, only the first message will be

displayed. To clear an Alarm or Warning, see the Protection

Systems section - Clear Alarm.

The display backlight is normally off. If the user presses any •

key, the backlight will come on automatically and remain on for

30 seconds after the last key was pressed.

The “Main Menu” page will allow the user to navigate to all other •

pages or sub-menus by using the Left/Right and Enter keys.

This page can be accessed at any time with several presses of

the dedicated Escape key. Each press of the Escape key takes

you back to the previous menu until the main menu is reached.

This page displays the following options: HISTORY; STATUS;

EDIT; AND DEBUG. (See the Appendix - "Menu System".)

3.2 AUTOMATIC TRANSFER OPERATION

To select automatic operation, do the following:

1. Make sure the transfer switch main contacts are set to their

UTILITY position, i.e., loads connected to the utility power

source (Figure 3.2).

2. Be sure that normal UTILITY power source voltage is avail-

able to transfer switch terminal lugs N1 and N2 (Refer to the

Electrical Data section).

3. Set the generator’s AUTO/OFF/MANUAL switch to AUTO.

4. Set the generator’s main circuit breaker to its ON (or CLOSED)

position.

With the preceding steps complete, the generator will start auto-

matically when utility source voltage drops below a preset level.

After the unit starts, loads are transferred to the standby power

source. Refer to the Sequence of Automatic Operation section.

Section 3 — Operation

Air-cooled Generators

La page est en cours de chargement...

Generac 14 kW 0056120 Manuel utilisateur

Generac 14 kW 0056120 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents